1:1:1:1.

LENGTH:
PHYSICS Length is the distance between any two points.
Physics is a branch of science that deals with the study of It can also be defined as the distance covered by matter. It is
matter, energy and their interactions. a measurement of the extent of something from end to end.

Branches of Physics The S.I unit of length is a metre (m).

1. Mechanics: Motion and properties of matter. Other units of length include; Miles, kilometer, Hectometre,
2. Heat: A form of energy that causes rise in Decametre, Decimetre, Centimetre, etc.
temperature.
3. Optics: Light and waves. CONVERSIONS
4. Electricity and Magnetism. Example: 1
5. Modern Physics: Atomic and Nuclear Physics. Convert the following as instructed:
(i) 16.4mm to metres
Why we study Physics (ii) 20m to centimetres
 To help students develop an experimental attitude by (iii) 0.092km to metres
performing experiments and acquire skills such as (iv) 250cm to metres
observation, measuring, drawing logical conclusions.
 To understand scientific theories, principles and Solution
concepts (i) 16.4mm to metres
 To prepare students for further studies in Physics. km Hm Dm M dm cm mm
 To understand the applicability of Physics in other 1 0 0 0
disciplines like security, medicine, engineering, e.t.c 1m = 1000mm
and improve the world’s technology.
x = 16.4mm
1000𝑥 = 16.4 × 1𝑚
1 MECHANICS AND PROPERTIES 1000𝑥 = 16.4
OF MATTER 1000𝑥 16.4
=
1000 1000
𝑥 = 0.0164𝑚
1:1. MEASUREMENTS: Thus 16.4mm = 0.0164 m

Physics is concerned with measurement of physical (ii) 20m to centimetres

quantities and classifying them into groups according to Solution
their nature. 20m to centimetres
To measure is to find the value of a physical quantity using Km Hm Dm M dm Cm Mm
a scientific instrument with a standard scale. 1 0 0
1m = 100cm
Physical Quantities 20m = X
A physical quantity is a physical property that can
accurately be measured. 1 × 𝑥 = 20 × 100𝑐𝑚
𝑥 = 2000 𝑐𝑚
Types of Physical Quantities Thus 20m = 2000 cm
There are two types of Physical Quantities namely;
(i) Fundamental Quantities or Basic Quantities (iii) 0.092km to metres
(ii) Derived Quantities Solution
0.092km to metres
1:1:1. FUNDAMENTAL QUANTITIES OR BASIC Km Hm Dm M dm cm Mm
QUANTITIES 1 0 0 0
These are quantities from which all other quantities are 1km = 1000m
obtained. They are seven in total and these are: 0.092km = X

Fundamental Quantities S.I unit Symbol 𝑥 = 0.092 × 1000𝑚

1. 𝐋𝐞𝐧𝐠𝐭𝐡 Metre M 𝑥 = 92 𝑚
𝑥 = 92 𝑚
2. 𝐌𝐚𝐬𝐬 Kilogrm Kg
Thus 0.092km = 92 m
3. 𝐓𝐢𝐦𝐞 Second S
4. Thermodynamic TemperatureKelvin K
(iv) 250cm to metres
5. Electric current Ampere A
Solution
6. Amount of a substance Mole Mol. 250cm to metres
7. Luminous Intensity Candela Cd Km Hm Dm m Dm cm mm
1 0 0
Note: In mechanics, we use only three fundamental 1m = 100cm
quantities; i.e length, mass and time.
x = 250cm

©[email protected] 1
100 × 𝑥 = 250 × 1𝑚 Reading of vernier calipers,
100𝑥 250 1. Record the reading on the main scale to two places in cm.
= 2. Look along the Vernier scale carefully until you see
100 100
𝑥 = 2.5𝑐𝑚 division on it which coincides with the main scale, this gives
Thus 250cm = 2.5m the second decimal place.

Examples:
Instruments Used in measuring length
(i) Tape-measure: (Accurately measures length greater
than 1metre:𝑙 > 1𝑚). E g length of a foot ball field,
length of a plot of land etc.

(ii) Metre-rule :( Accurately measures length greater than

12 centimetres but less than 1metre:12𝑐𝑚 < 𝑙 < 1𝑚).
Eg length of a desk, breadth of a window, etc.
A metre rule gives readings in cm to 1dp. Main scale = 2.40cm
Vernier scale = 0.04cm
(iii) Vernier calipers or Slide calipers : Final reading = 2.44cm
Accurately measures length greater than 1cm but less than
12 cm:2.5cm < 𝑙 < 12 cm. E.g Internal and External What readings are represented in the diagram?
diameters of test tubes and beakers, breadth of a metre rule.
etc.
A vernier caliper gives readings in cm to 2dp.

Main scale

(iv) Micrometer screw gauge: (Accurately measures

length less than 1centimetre: 1𝑚𝑚 < 𝑙 < 25𝑚𝑚). Eg
Diameter of wires, Diameter of ball beairings and
pendulum bob, etc.
Vernier scale A micrometer screw gauge gives readings in cm to 2dp.

Engineer calipers

For each turn the spindle moves through 0.5mm.The

fraction of each turn is indicated on the thimble. This has a
1
scale of 50 divisions on the thimble and represents of half
50
1
a millimeter i.e. × 0.5 mm = 0.01mm.
The distance between the jaws is after wards measured on 10
The sleeve-reading gives units to the 1st two decimal places
an ordinary scale like a metre-rule. and the thimble gives 2nd decimal place.

Example I:
How to read a vernier Caliper

Sleeve scale reading = 14.50mm

Thimble scale reading = 0.44mm
= 14.94mm
 The main scale is in centimeters, 1cm has 10 divisions
1 Example II:
each division is cm = 0.1cm.
10
1
 Vernier scale, each division is cm = 0.01cm.
100

©[email protected] 2
 2kg = X
1 × 𝑥 = 2 × 10000𝑑𝑔
𝑥 = 20,000𝑑𝑔
Thus 2 kilograms = 20000dg

(iii) 40mg to kg
Solution
40mg to kg
Sleeve scale reading = 9.5 00mm
Thimble scale reading = 0.29mm Kg Hg Dg G dg Cg mg
= 9.79mm 1 0 0 0 0 0 0
1kg = 1000000mg
Precautions taken when using a micrometer screw gauge x = 40mg
 The faces of the anvil and the spindle must be cleaned
to remove dust so as to get accurate readings. 1000000 × 𝑥 = 40 × 1𝑘𝑔
1000000𝑥 40
 The reading must be checked. =
1000000 1000000
𝑥 = 0.00004𝑘𝑔
1:1:1:2: MASS: Thus 40miligrams = 0.0000kg
Mass is the quantity of matter in a substance.
The S.I unit of mass is a kilogram (kg). (iv) 20.55g to cg
Other units of mass include: Tonnes (1tonne = 1000kg), Solution
Hectogram (Hg), Decagram (Dg), Gram (g), Decigram (dg), 20.55g to cg
Centigram (cg), Milligram (mg), etc. Kg Hg Dg g dg Cg mg
1 0 0
Instruments Used in measuring Mass 1g = 100cg
(i) weighing beam balance (iv) Lever arm beam balance 20.55g = X
(ii) Digital beam balance (v) Tripple beam balance
(iii) Top arm beam balance 1 × 𝑥 = 20.55 × 100𝑐𝑔
𝑥 = 2055𝑐𝑔
Thus 20.55grams = 2055cg

1:1:1:3: TIME:
Time is the interval between two events.
The S.I unit of time is a second (s).
Other units of time include Minute (1min = 60s), Hour
(1hr=60min), Day (1day=24hrs), Week (7 days), fortnight
(2weeks), Month (1month=30days), Year (1yr=12months),
Conversions
decade, century, and a millennium.
Example 1:
Convert the following as instructed:
Instruments Used in measuring Time
(i) 100grams to kilograms
(ii) 2kg to dg  Stop clock
(iii) 40mg to kg  stop watch
(iv) 20.55g to cg  Half life of a radioactive substance eg Carbon – 14
 Shadows
Solution
(i) 100grams to kilograms 1:1:2. DERIVED QUANTITIES
Kg Hg Dg G Dg Cg Mg These are quantities which can be expressed in terms of the
1 0 0 0 fundamental quantities. Besides the seven fundamental
1kg = 1000g quantities, the rest of the Physical quantities’ are derived
quantities. Their S.I units are also called Derived units.
x = 100g
1000 × 𝑥 = 100 × 1𝑘𝑔 Examples of Derived Physical quantities include:
1000𝑥 100 Derived Quantities S.I unit Symbol
= 1. Area squaremetre m2
1000 1000
𝑥 = 0.1𝑘𝑔 2. Volume cubicmetres m3
Thus 100grams = 0.1kg 3. Density kilogram per kgm−3
cubicmetre
(ii) 2kg to dg 4. Speed and Velocity metres per second ms −1
Solution 5. Pressure newton per square Nm−2
2kg to dg metre (or pascal) (or Pa)
Kg Hg Dg G dg Cg mg 6. Force and weight Newton N
1 0 0 0 0 E. t. c
1kg = 10,000dg

©[email protected] 3
1:1:2:1. AREA: Types of areas
Area is ameasure of the size of a surface. (i) Cross-sectional area
The S.I unit is a squaremetre (m2). (ii) Surface area
Other units of area include:
𝑐𝑚2 , 𝑚𝑚2 , 𝑘𝑚2 𝑒. 𝑡. 𝑐 Figure Name Formula for
Area
Example 1: 1. Rectangle 𝐴 = 𝑙𝑤
Convert the following as instructed w
(i) 15 mm2 to cm2
l
(ii) 20 m2 to mm2
(iii) 16.4 mm2 to m2 2. Square 𝐴 = 𝑆2
Solution s (All sides
(i) 15 𝑚𝑚2 𝑡𝑜 𝑐𝑚2 are equal)
Km Hm Dm M dm Cm Mm 3. Triangle 1
𝐴= 𝑏ℎ
1 0 2
1cm = 10mm h
(1cm)2 = (10mm)2 b
2 2
1cm = 100mm 4. Circle 𝐴 = 𝜋𝑟 2
2
x = 15 mm r
2
100 × 𝑥 = 15 × 1𝑐𝑚
𝑥 = 0.15𝑐𝑚2
Thus 15 𝑚𝑚2 =0.15𝑐𝑚2 1
5. Trapezium
b (2 parallel 𝐴 = ℎ(𝑎 + 𝑏)
2
(ii) 20 𝑚2 𝑡𝑜 𝑚𝑚2 un equal
km Hm Dm M dm Cm Mm h sides)
1 0 0 0
1m = 1000mm a
(1m)2 = (1000mm)2 6. Sphere 𝑆. 𝐴 = 4𝜋𝑟 2
1m2 = 1000000mm2
20 m2 = X
7. Cuboid 𝑆. 𝐴
1 × x = 20 × 1000000mm2 h = 2(𝑙𝑤)
x = 20,000,000mm2 + 2(𝑤ℎ)
Thus 20 m2 =20,000,000mm2 or 𝟐. 𝟎 × 𝟏𝟎𝟕 𝐦𝐦𝟐 w + 2(𝑙ℎ)
l
Solution 8. Cube 𝑆. 𝐴 = 6𝑆 2
(All faces
(iii) 16.4 𝑚𝑚2 𝑡𝑜 𝑚2
are equal)
Km Hm Dm M dm Cm Mm
1 0 0 0
1m = 1000mm 1:1:2:2. VOLUME:
(1m)2 = (1000mm)2 Volume is the space occupied by matter.
The S.I unit of volume is cubic metre (m3).
1m2 = 1000000mm2 Other units of volume include:
x = 16.4 mm 2 𝑐𝑚3 , 𝑚𝑚3 , 𝑘𝑚3 , 𝑚𝑖𝑙𝑙𝑖𝑙𝑖𝑡𝑟𝑒(𝑚𝑙), 𝑙𝑖𝑡𝑟𝑒(𝑙). 𝑒. 𝑡. 𝑐
1000000 × x = 16.4 × 1m2 Instruments for measuring Volume include:
1000000x 16.4
=  Measuring cylinder
1000000 1000000  Volumetric flask
x = 0.0000164m2
 Burette
Thus 20 m = 0.0000164m2 or 𝟏. 𝟔𝟒 × 𝟏𝟎−𝟓 𝐦𝟐
2
 Pipette

©[email protected] 4
Volume of regular objects
Figure Name Formula for
Volume
1. Cylinder 𝑉 = 𝜋𝑟 2 ℎ

Circular 1
cone 𝑉 = (𝜋𝑟 2 )ℎ
3

2. Question:
A measuring cylinder containing some water stands on a
3. Sphere 4
𝑉 = 𝜋𝑟 3 scale pan. A solid ball is lowered into the water. The water
3 level rises from the 30cm3 mark to 40cm3 mark. The scale
reading increases from 100g to 180g.
4. Cuboid 𝑉 = 𝑙𝑤ℎ

5. Cube 𝑉 = 𝑆3
(All faces
are equal)

Experiment to determine the volume of an irregular

object
The volume of an irregular object can be obtained by the What is the density of the material of the ball?
Displacement method. A. 2.0 gcm−3 . B. 4.5 gcm−3 .
 Pour water into a measuring cylinder up to a certain B. 8.0 gcm . −3
D. 18 gcm−3 .
level. Record the volume of water (V1).
 Tie a thread on the irregular object and gently lower it Example 1:
into the water in the measuring cylinder. Note the new Convert the following as instructed
volume of water in the cylinder (V2). (i) 250 𝑐𝑚3 𝑡𝑜 𝑚3 (𝑖𝑖𝑖)0.032𝑘𝑚3 𝑡𝑜 𝑚3
3 (𝑖𝑣)10,000 𝑙𝑖𝑡𝑟𝑒𝑠 𝑡𝑜 𝑚3
 The Volume of the irregular object is then equal to the (ii) 500𝑚𝑙 𝑡𝑜 𝑚
volume of displaced water; Thus V = (V2 – V1).
Solution
(i) 250 𝑐𝑚3 𝑡𝑜 𝑚3
Km Hm Dm m dm Cm mm
1 0 0
1m = 100cm
(1m)3 = (100cm)3
1m3 = 1000000cm3
x = 250cm3
1000000 × 𝑥 = 250 × 1𝑚3
1000000𝑥 250
=
1000000 1000000
OR 𝑥 = 0.00025 𝑚3
 Pour water in an over flow can up to the level of the Thus 250 𝑐𝑚3 = 0.00025𝑚3 𝑜𝑟 𝟐. 𝟓 × 𝟏𝟎−𝟒 𝒎𝟑
spout. Place a measuring cylinder just below the spout.
 Tie a thread around the irregular object and gently Example 2:
lower it into the overflow can. Use the match box below to answer questions that follow.
 Note the volume of water, V that collects in the
measuring cylinder. It is equal to the volume of the 5cm
irregular object.

10cm

8cm

©[email protected] 5
Find the volume Tapped zeros; zeros between significant figures i.e. zeros
(i) in cm3 [400cm3 ] between non zero digits are significant figures e.g. 6.0037
(ii) in m3 [0.0004m3] (5s.f), 0.0100034 (6 s.f).

Exercise: Trailing zeros (zeros at the right end of a number);

1. A cuboid has dimensions 2cm by 10cm. Find its width in (i) Trailing after a decimal point: These are significant
metre if it occupies a volume of 80cm3. [ 0.04m] figures. E.g 2.00 (3s.f), 0.0020 (2s.f), 0.0120700 (6s.f)
Normally these values are obtained by using an instrument.
2. (a) Find the volume of water in a cylinder of water radius
7cm if its height is 10cm.[ 1540cm3] (ii) Trailing before a decimal point: These are NOT
(b) The volume of the cylinder was 120m3.When a stone significant figures. E.g 20 (1s.f), 2400 (2s.f), 580100 (4s.f)
was lowered in the cylinder filled with water the volume Normally these values are obtained as a result of rounding
increased to 15cm3. Find the height of the cylinder of radius off certain numbers to the nearest tens, fifties, hundreds,
7cm. [0.078 cm] thousands, ten thousands e.t.c.
For example, if a number 348 is rounded off to 1 s.f, we get
3. A Perspex box has 10cm square base and contains water 300 and if it`s rounded off to 2 s.f we get 350. The trailing
to a height of 10cm. A piece of rock of mass 600g is zeros in these approximations (i.e. 300 and 350) are due to
lowered gently into the water and the level rises to 12cm. rounding off and therefore are not significant.
Find the;
(i) Volume of water displaced by the rock. Questions
(ii) volume of the rock in 𝒄𝒎𝟑 and 𝒎𝟑 Write the following to the stated significant figures
(iii) density of the rock in 𝒈𝒄𝒎−𝟑 and 𝒌𝒈𝒎−𝟑 a) 28.8 to 3 s.f b)
2
to 2 s.f c) 4.027 x10-2 to 3 s.f
7
1:1:3. SCIENTIFIC NOTATION AND SIGNIFICANT Prefix and Surfix Symbol Exponent
FIGURES. Tera T 1012
Scientific notation or Standard form Giga G 109
Mega M 106
 A number is in scientific form, when it is written as a
vnumber between 1 and 9 which is multiplied by a Kilo K 103
power of 10. i.e when it is written in the form 𝐀 × 𝟏𝟎𝐧 . Hecto H 102
Where1 ≤ A < 10; i.e A lies between 1 and 10 with 1 Deca D 101
inclusive but 10 exclusive. n is an integer (….-2,-1,0,1,2…). Metre 𝟏𝟎𝟎
Deci d 10−1
 Scientific notation is used for writing down very large Centi c 10−2
and very small measurements. Mili m 10−3
Micro µ 10−6
Example: Nano n 10−9
(i) 598,000,000m = 5.98 x 108 m Pico p 10−12
(ii) 0.00000087m = 8.7 x 10-7 m Fermto F 10−15
(iii) 60220m = 6.022 x 104 m Atto A 10−18
Questions: Example:
Convert the following to scientific form. Value Scientific form Prefix used
(a) 0.048 = 4.8 x 10-2
3
3000W 3 × 103 W 3kW
-1
(b) = 0.75 = 7.5 x 10 4900 000J 4.9 × 106 J 4.9MJ
4
(c) 1000 = 1.0 x 103 0.00526m 5.26 × 10−3 m 5.26mm
(d) 8.72 = 8.72 x 100 0.00000125g 1.25 × 10−6 g 1.25µg
1
(e) = 0.125 = 1.25 x 10-1
8

Significant figures
 Decimal Places
The number of decimal places (dp) is the number of digits to
the right end of a decimal point. E.g. the number 3.6420 is
given to 4dp.Thus 3.6420 ≈ 3.642(3dp), 3.6420 ≈ 3.64(2dp),
3.6420 ≈ 3.6(1dp), 3 .6420 ≈ 4 (0dp).

 Significant Figures
a) None zero digits (1, 2, 3, 4, 5, 6, 7, 8 and 9) are
significant figures.
b) Zeros
Leading zeros (i.e. zeros at the left end of a number) i.e
zeros before the first significant figure; are not significant
figures e.g. 0.000456 (3s.f), 0.017 (2s.f).

©[email protected] 6
  An empty measuring cylinder is weighed on a beam
1:2. DENSITY AND RELATIVE DENSITY balance and its mass, Mo is noted.
 A liquid is added to it and it is weighed again using the
1:2:1. DENSITY beam balance;
Density is the mass per unit volume: 𝑚𝑎𝑠𝑠 𝑜𝑓 𝑚𝑎𝑠𝑠 𝑜𝑓
mass 𝑀𝑎𝑠𝑠
Density = ( )=( 𝑒𝑚𝑝𝑡𝑦 ) – ( 𝑐𝑦𝑙𝑖𝑛𝑑𝑒𝑟 )
volume 𝑜𝑓 𝑙𝑖𝑞𝑢𝑖𝑑
𝑐𝑦𝑙𝑖𝑛𝑑𝑒𝑟 𝑤𝑖𝑡ℎ 𝑙𝑖𝑞𝑢𝑖𝑑.
The SI unit is kg/m3 or kgm-3 other units are g/l or gcm -3
mass of liquid
Note: the density of pure water is 1000kgm-3 or 1gcm-3 Density of liquid =
volume of liquid
Changing gcm-3 to kgm-3
1gcm-3 = 1000kgm-3 (d) Air
So when changing gcm-3 to kgm-3 simply multiplies by 1000

Example:
Express 0.8 gcm -3 in kgm-3

1gcm-3= 1000kgm-3
0.8 = x
𝑥 = 0.8 × 1000𝑘𝑔𝑚−3
𝑥 = 800𝑘𝑚−3
Thus 0.8𝑔𝑐𝑚−3 = 800𝑘𝑔𝑚−3

1:1:2:3:1. Simple density Measurements

When the mass “M” and volume “V” of a substance are (i) Measuring of mass
known; then the density is obtained from: A round-bottomed flask is weighed using a beam balance
𝒎 when full of air and after removing the air using a vacuum
𝐷𝑒𝑛𝑠𝑖𝑡𝑦, 𝛒 = pump. Then
𝑽
(ii) Measuring of volume
(a) For a Regularly shaped solid The volume of air is found by filling the flask with water
 The mass of the solid is measured on a beam balance and pouring it into a measuring cylinder. Then volume of air
 The volume of the solid is obtained by measuring the = volume of water transferred into the measuring cylinder.
sides of the solid using a ruler, veneer calipers or mass of air
Density of air =
micrometer screw gauge. volume of air
 The density is then got from the formula. Precautions taken
mass of solid -The flask should be dried
Density of solid = -The atmospheric pressure and temperature should be noted.
volume of solid
-The air should be dry
(b) For an irregularly – shaped solid
 The solid is weighed using a beam balance to obtain its Factors that affect Density
mass. (i) Temperature
 The volume of the solid is obtained by displacement When the temperature of a substance is increased, it expands
methods; using a displacement can. The volume of hence increasing its volume. The density then decreases.
displaced water is equal to the volume of the solid. When the temperature of a substance is reduced, it contracts
 The density is then got from the formula. hence reducing its volume. The density then increases.
mass of solid
Density of solid = (ii) Pressure
volume of solid
Pressure only affects the density of gases.
NOTE: When the pressure of a given mass of a gas is increased, the
1. For a floating object. Tie a sinker on the floating object gas molecules become squeezed and occupy a smaller
and gently dip it water. Get the volume of the water volume. This increases the density of the gas.
displaced, V1. When the pressure of a given mass of a gas is reduced, the
Then dip the sinker alone in the water and again get the gas molecules become occupy a larger volume. This
volume of water displaced, V2. decreases the density of the gas.
The volume of the floating object, V = V1 – V2
Uses of density
2. For a pin or a ball bearing. It is used to: -Identify materials for construction
-Test the purity of a substance
(c) For liquids -Choose the light gases to fill balloons
 The volume of the liquid is measured using a measuring Example 1:
cylinder and the volume, V is noted. A Perspex box has a10cm square base containing water to a
height of10 cm. A piece of rock of mass 600g is lowered
into the water and the level rises to 12 cm.
©[email protected] 7
(a) What is the volume of water displaced by the rock? 2
(iii) Find the density of the stone. [ g/cm3]
5
V = Lxwxh
= 10 x10 x (12-10)
5. A steel C.P.U below, has a mass of 560g
= 200 cm3

(b) What is the volume of the rock? 40cm

Volume of rock = volume of water displaced
= 200cm3
20cm
100cm
Alternatively,
Find its density (i) in g/cm3 (ii) in kg/m3
Volume of water before adding the rock
V1 = LxWxH
6. 200g of liquid Y of density 4gcm-3. Calculate the density
= (10cm x 10cm x 10cm)
of the mixture.
= 1000cm3
7. Liquids X and Yare mixed to form a solution. If the
density of X is 0.8gcm-3 and volume is 100cm3, density of Y
Volume of water after adding the rock
1.5cm-3 and its volume is 300m3.Find the;
V2 = LxWxH
(i) mass of liquid X [80g]
= (10 x 10 x 12) cm3
(ii) mass of liquid Y [450g]
= 1200cm3
(iii) Density of a mixture [1.325gcm-3]
Volume of water displaced
7. In an experiment to determine the density of a pin,
V= V2 – V
100pins are gently lowered into a measuring cylinder
= (1200 – 1000) cm3
containing 12cm3 of water. The water in the cylinder rose to
= 200cm3
98cm3. Find the;
(i) volume of a pin.
(c) Calculate the density of the rock
mass 600 g (ii) density of the pin in kgm-3
−3
Density = = 3 = 3gcm
volume 200cm
1:2:2. DENSITY OF MIXTURES
Example 2: Suppose two substances are mixed as follows:
(ii) The mass of 24.4cm3 of mercury is 332g. Find the Substance Mass Volume Density
density of mercury.(=13.6 gcm-3) X MX VX MX
(iii) An 800g solid measures 10cm by 5cm by 4cm. DX =
VX
Determine its density.(= 4 gcm-3) Y MY VY MY
DY =
(iv) A glass stopper of volume 16cm3 weighs 40g. Calculate VY
its density in : (i) gcm-3 .(=2.5 gcm-3)
(ii) kgm-3. (=2500kgm-3) 𝐦𝐚𝐬𝐬 𝐨𝐟 𝐦𝐢𝐱𝐭𝐮𝐫𝐞
(v) The density of copper is 8.9gcm-3. What is the mass of 𝐃𝐞𝐧𝐬𝐢𝐭𝐲 𝐨𝐟 𝐦𝐢𝐱𝐭𝐮𝐫𝐞 =
𝐕𝐨𝐥𝐮𝐦𝐞 𝐨𝐟 𝐦𝐢𝐱𝐭𝐮𝐫𝐞
100cm3 of copper? .(=890 g)
(vi) When a piece of irregular stone of mass200g is lowered MX + MY
Density of mixture =
in a measuring cylinder, the initial and final volumes VX + VY
were 500cm3 and 600cm3 respectively. Calculate the
density of the stone.(=2gcm-3) Example: 1
(vii) An empty beaker weighs 120g in air and 180g when 100cm3 of fresh water of mass100g is mixed with 100 cm3
filled with 75cm3 of methylated spirit. Find the density of sea water of mass103g. Calculate the density of the
of methylated spirit. (=0.8gcm-3) mixture.
(viii) What is the mass of 1.5litres of water? (= 1.5kg) Solution
mass of mixture
2. The oil level in a burette is 25cm3.50 drops of oil fall Density of mixture =
Volume of mixture
from a burette. If the volume of one drop is 0.1cm3.What is
the final oil level in the burette. [30cm3] Density of mixture
mass of fresh water + mass of sea water
3. A measuring cylinder has water level of 13cm.What will =
Vol. of fresh water + Volume of sea water
be the new water level if 1.6g of a metallic block of density
0.8g/cm3 is added.
100 + 103
4. A perspex box having 6cm square base contains water to Density of mixture =
100 + 100
a height of 10cm.
(a) Find the volume of water in the box [360cm3] 203
=
200
(b) A stone of mass 120g is lowered into the box and the 𝐃𝐞𝐧𝐬𝐢𝐭𝐲 𝐨𝐟 𝐦𝐢𝐱𝐭𝐮𝐫𝐞 = 𝟏. 𝟎𝟏𝟓 gcm-3
level of water rises to 13cm.
(i) Find the new volume of water? [468cm3] Example 2:
(ii) Find the volume of the stone? [108 cm3]

©[email protected] 8
Liquid Y of volume 0.40m3 and density 90.0kgm-3 is mixed
with liquid X of volume0.35m3 and density 800kgm-3.
Calculate the density of the mixture.

Solution
mass of Y = Volume of Y × Density of Y
mass of Y = 0.40 × 90.0
mass of Y = 360kg

mass of X = Volume of X × Density of X

mass of Y = 0.35 × 800 The bottle contains exactly the same volume when the liquid
mass of Y = 280kg level is at the hole.
.Then:  mass of empty bottle M0
mass of mixture A dry density bottle with a stopper is weighed when empty
Density of mixture = using a balance.
Volume of mixture
 Mass of bottle filled with the liquid M2
Density of mixture A dry density bottle with a stopper is weighed when filled
mass of liquid Y + mass of liquid X with the liquid using a balance.
=  Mass of bottle filled with water M1
Volume ofliquid Y + Volume of liquid X
360 + 280 After removing the liquid and rinsing out the density bottle
Density of mixture = with water, the density bottle is filled with water and
0.40 + 0.35 weighed again.
640kg  The measurements are recorded as below:
= Mass of empty: = m0
0.75m3 Mass of bottle full of water: = m1
𝐃𝐞𝐧𝐬𝐢𝐭𝐲 𝐨𝐟 𝐦𝐢𝐱𝐭𝐮𝐫𝐞 = 𝟖𝟓𝟑. 𝟑𝟑𝐤𝐠m-3
Mass of bottle full of liquid: = m2
Exercise: Mass of liquid: = m2 −m0
1. An alloy is formed by adding 500g of element P of Mass of water: = m1 −m0
density 5gcm-3 to 400cm3 of element Q of density 4gcm-3. 𝐦𝟐 −𝐦𝟎
Calculate the density of the alloy.[ 4.2gcm-3]  Relative Density of a liquid =
𝐦𝟏 −𝐦𝟎

2. 500cm3 of liquid X of density 2gcm-3 is combined with Note: The advantage of using a density bottle in measuring
200 g of liquid Y of density 4gcm-3. Calculate the density of the relative density of a solid is that it is accurate compared
the mixture. to other methods.

3. Liquid M of density 0.5gcm-3 is mixed with liquid N in Measurement of relative density of a solid
equal volumes. If the mixture has a density of 0.8gcm-3 ,  This can be found by weighing the solid in air and when
Find the density of liquid N. fully immersed in water.
 The solid immersed in water displaces an amount of
4. 3cm-3of water was mixed with 5cm-3 of milk of density water equal to its volume. The relative density is then
1500kgm-3. Find the density of the mixture. [1312.5kgm-3] calculated using;
 Relative density = Weight in air = Wa
5. Liquid A of volume 400cm3 and density 800kgm-3 is Weight in water Wa −Ww
mixed with liquid B of volume 600cm3 and density
1120kgm-3. Calculate the density of the mixture. Example 1
A density bottle was used to measure the density of
1:2:3. RELATIVE DENSITY (R.D) mercury. The following measurements were taken:
Relative density is defined as the ratio of the density of a  Mass of empty bottle = 20g
substance to the density of an equal volume of water.  Mass of bottle full of mercury = 360g
Density of substance  Mass of bottle full of water = 45g
Relative Density = Calculate the;
Density of equal volume of water
a. Relative density of mercury
Note: Density of pure water =1gcm-3 = 1000kgm-3 since b. Density of mercury
density = mass ⁄ Volume, Then:
mass of substance Solution
Relative Density = (i) (ii)
mass of equal volume of water m2 − m0 Density mercury
R. D = R. D =
weight of substance m1 − m0 Density of water
Relative Density = ρ
weight of equal volume of water 360 − 20 13.6 =
R. D = 1000
45 − 20 𝜌 = 13.6 × 1000
Note: Relative density has no units.
𝜌 = 13600𝑘𝑔𝑚−3
340
Experiment: To determine the Relative density of a liquid R. D =
25
using a density bottle. R. D = 13.6

©[email protected] 9
Example: 2 A: 160 cm3 B: 600 cm3
3
A density bottle has mass 75g when empty, 95g when full of C: 760 cm D: 1000 cm3
water and 99g when full of a liquid. Calculate the: 12. What mass of lead has the same volume as 1600 kg of
(i) Relative density of the liquid. petrol? {Density of lead = 11400 kg m-3, Density of petrol
(ii) density of the liquid = 800 kg m-3}
Solution A. 22 800 kg C. 1600 kg
mE = 75g; mL = 99g; mW = 95g B. C. 11400 kg D. 800 kg
(i) (ii)
mL − mE Density of liquid 13. A metal cuboid of dimensions 3 cm by 2 cm by 1 cm
R. D = R. D =
mW − mE Density of water and 8.9 g cm-3 is completely immersed in a liquid of density
ρ 0.8 g cm-3. The mass of the liquid displaced is
99 − 75 1.2 = A. 53.4 g. B. 29.1 g.
R. D = 1000
95 − 75 𝜌 = 1.2 × 1000 B. C. 7.5 g. D. 4.8 g.
𝜌 = 1200𝑘𝑔𝑚−3
24 14. A tank 2m tall and base area of 2.5m2 is filled to the
R. D = brim with a liquid, which weighs 40000N. Calculate, the
20
R. D = 1.2 density of the liquid in kg/m3.
4000 4000
A. C.
2×2.5×10 2×2.5×10
Exercise:
1. A bottle full of water has a mass of 45g, when full of 40000 40000
ethanol, its massis36g. If the empty bottle weighs 20g, B. D.
2×2.5×10 2×25
calculate the density of ethanol.

2. Density bottle has a mass of 70g when empty, 90g when 1:3. SCALARS AND VECTORS
full of water and 94g when full of liquid.
Find the relative density of the liquid and its density. Physical quantities can be divided into two types namely:
i) Scalar quantity ii) Vector quantity
3. An empty 60-litre petrol tank weighs10kg. What will be
its mass when full of petrol of relative density 0.72? A scalar quantity is physical quantity which has magnitude
only.
4. A density bottle was used to measure the relative density Examples: Mass, volume, time, temperature distance,
of a liquid and the following results were obtained. pressure etc.
Mass of empty bottle : =30g
Mass of bottle full of water : =130g A vector quantity is a physical quantity which has both
Mass of bottle full of liquid : =110g magnitude and direction.
Calculate the density of the liquid. (=0.8gcm-3) Examples: Velocity, acceleration, force, momentum
displacement, Electric and magnetic field intensities.
5. An empty density bottle is 46.00g. When fully filled with
water, it weighs 96.00g. It weighs 86.00g when full of an Resultant Vector
unknown liquid. Find the density of the liquid. (=0.8gcm-3) A resultant vector is a single vector which produces the
6. A piece of aluminum weighs 80N in air and 50.37N when same effect on an object as two or more vectors acting on
completely immersed in water. Calculate the relative density the same body.
of aluminum. (=2.7) Moving from O to B along OB is the same as moving
through OA followed by AB. This shows that a single vector
7. Two solid cubes have the same mass but their surface OB produces the same effect as adding; ⃗⃗⃗⃗⃗
OB = ⃗⃗⃗⃗⃗
OA + ⃗⃗⃗⃗⃗
AB
areas are in the ratio of 1 : 16. What is the ratio of their
densities? In general the resultant force is calculated by adding all the
A. 1 : 2 B. 4 : 1 force. But when the forces are in opposite direction the
C. 64 : 1 D. 1 : 64 resultant force is calculated by subtracting.

9. A metal cuboid of dimensions 3 cm by 2 cm by 1 cm and Addition and subtraction of vectors

8.9 g cm-3 is completely immersed in a liquid of density 0.8 The addition of vector takes place so long as the directions
g cm-3. The mass of the liquid displaced is. are the same though the magnitude may differ.
A. 53.4 g. C. 29.1 g. The subtraction occurs when the directions are opposite.
B. 7.5 g. D. 4.8 g.
Example 1:
10. 0.002m3 of a liquid of density 800kgm-3 is mixed with A goat moves 13m west and continue moving west ward
0.003m3 of another liquid of density 1200kgm-3. What is the 5m. Find the resultant displacement of the got .
density of the mixture?
A. 1,000 kgm-3 B. 4,000 kgm-3 13m 5m
-3
C. 2,500 kgm D. 1,040 kgm-3 SH =13+5
=18m in the western direction
11. A bottle weighs 160 g when empty, 760 g when filled
with water, and 1 kg when filled with a certain liquid.
Calculate the volume of the liquid in bottle.

©[email protected] 10
Example 2: R = ±5N
Move 13m west and the move 5m east ∴The magnitude of the resultant
force is 5N
13m
5m Example 6
The figure below shows five forces acting on a 2.5kg mass.
SH =13-5
=8m in the western direction 9N

Example 3:
Three force of 3, 5N and 7N act on an object A as shown. 12N
Find single vector which can produce the same effect. 7N

3N 13N 8N
5N
7N Calculate the;
FH = (3+7) - 5 (i) resultant force on the mass
=5N towards the East (ii) direction of the resultant force
(iii) acceleration of the mass
Example 4
Three force of 3, 5N and 7N act on an object A as shown. Solution
Find single vector which can produce the same effect. (i) FH = (12 − 7)N = 5N →
FV = {(13 + 8)N − 9N} = 12N ↓
 Resultant Vector diagram
6N 3N
5N

θ
12N
15 R
N
FV =15- (6+3)
= 6N towards the South

Example 5  The magnitude of the resultant force

Two force of 3 and 4N act on an object as shown. Find Using the Pythogras theorem;
single force which can produce the same effect as the two (𝐇𝐲𝐩𝐨𝐭𝐞𝐧𝐮𝐬𝐞)𝟐 = (𝐁𝐚𝐬𝐞)𝟐 + (𝐇𝐞𝐢𝐠𝐡𝐭)𝟐
forces above. (R)2 = (b)2 + (h)2
2 2
R = 5 + 122
2
R = 169
3N R = ±√169
R = ±13N
∴The magnitude of the resultant force is 13N
4N (ii)
Solution:  Direction of the resultant force
FH = 4N Direction of the From the Vector diagram;
resultant force Height
tan θ =
FV = 3N From the Vector Base
diagram; 12
tan θ =
Resultant Vector diagram Height 5
tan θ = 12
Base θ = tan−1 ( )
3 5
3N tan θ = θ =67.40
R 4
3 ∴The direction of the resultant force is 67.40 below the
θ = tan−1 ( ) horizontal (or below the 4N force)
4
θ θ =36.90
4N (iii)
∴The direction of the  Acceleration of the mass
Magnitude of the resultant force
resultant force is From F = ma
Using the Pythogras theorem;
36.90 above the 13 = 2.5a
(𝐇𝐲𝐩𝐨𝐭𝐞𝐧𝐮𝐬𝐞)𝟐 = (𝐁𝐚𝐬𝐞)𝟐 13 2.5
+ (𝐇𝐞𝐢𝐠𝐡𝐭)𝟐 horizontal (or above the = a
2.5 2.5
2
(R) = (b) 2
+ (h)2 4N force) = a
2
R = 4 + 3 2 2 ∴ a = 0.48 ms −2
R2 = 25
R = ±√25 Example 7

©[email protected] 11
Two forces 6N and 8N act on 2kg body as shown. Calculate R = ±√169
(i) the resultant force (ii) the acceleration R = ±13N
∴The magnitude of the resultant force is 13N
6N
Example 8
300
A mass of 15kg is suspended using a string. The string is
8N
then pulled by a horizontal force F such that the string
Methode I: Using Graphical Method. makes an angle of 300 with the down ward vertical.
Procdures Calculate the;
 Choose a scale for the axes (i) Tension in the string.
 Draw the vectors at the given angle (ii) Horizontal force F.
 Complete the Parallelogram of vectors.
 Measure the length R of the diagonal Solution:
 Multiply R by the scale to get the resultant Vector.

Method II: Using the Cosine Rule.

300 T
300 T
F
6N R 15g

15kg
300 1500 300 F
W=mg=15g=15x10=150N
8N
2 2 2
a = b + c − 2bc cos θ The three forces are in equilibrium
R2 = 82 + 62 − 2(8)(6) cos 150 Step 1: forming a closed triangle
R2 = 64 + 36 − 104 cos 150 Step 2: resolving Vertically;
R2 = 100 − 104 cos 150 150 150
cos 30 = ⟺ T cos 30 = 150 ⟺ T = = 173.21N
R2 =190.07 T cos30
R = ±13.8 N Step 3: Resolving Horizontally
F
Method III: By Resolving the Forces Horizontally and Tan 30 = ⟺ 150 tan 30 = F ⟺ F = 86.6N
150
Vertically. OR
x F
sin 30 = ⟺ T sin 30 = F ⟺ F = 173sin30 = 86.6N
T
y
6N
600 Example 9
300 A block of mass 2kg is pulled along a rough horizontal
8N ground by a force of 120N, with the help of a string, which
makes an angle of 600 with the horizontal. If the friction
From the diagram; between the block and the ground is 50N, calculate the;
x (i) Resultant force on the block.
sin 60 =
6 (ii) Acceleration of the block.
x = 6 sin 60 = 6 × 0.8666 = N 120N
y
cos 60 =
6
y = 6 cos 60 = 6 × 0.5 = 3N
Then; 2kg 600
50N
FV = y = 3N
FH = x+8 = N
Solution
x

R 3N
y
120N
𝜃
300
N
600
Using the Pythogras theorem; 50N
𝟐 20N
(𝐇𝐲𝐩𝐨𝐭𝐞𝐧𝐮𝐬𝐞)𝟐 = (Ó𝐚𝐬𝐞) + (𝐇𝐞𝐢𝐠𝐡𝐭)𝟐
(R)2 = (b)2 + (h)2 From the diagram;
2 2
R = 5 + 32 x
2 sin 30 =
R = 169 120

©[email protected] 12
 x = 120 sin 30 = 120 × 0.5 = 60N Weight of body = mass of body “m” (kg) x acceleration due
y to gravity, g. W = mg
cos 30 =
120 The S.I unit of weight is a newton “N” Weight of a body
y = 120 cos 30 = 120 × 0.8666 = 18.51N varies from place to place or from planet to planet.
Then;
FV = 18.51+ (-20) = -1.49 N Why weight of a body varies
FH = 60+ (-50) =10 N Weight of a body varies because of the following reasons:
10N
i) The shape of the earth is not a perfect sphere. so at the
θ equator the value of acceleration due to gravity is less than
that at the pole. This makes the weight of the body to be less
R
1.49N at the equator and greater at the poles.

ii) Planets have different accelerations due to gravity. A

body resting on the surface experience a reaction force R
Using the Pythogras theorem; from the surface which supports it.
(𝐇𝐲𝐩𝐨𝐭𝐞𝐧𝐮𝐬𝐞)𝟐 = (𝐁𝐚𝐬𝐞)𝟐 + (𝐇𝐞𝐢𝐠𝐡𝐭)𝟐
(R)2 = (b)2 + (h)2
R 2
= 10 + 1.492
2 Normal Reaction, R
2
R = 102.2201
R = ±√102.2201
R = 10.11N
∴The magnitude of the resultant force is 10.11N

1:3:1. FORCES
A force is that which changes a body’s state of rest or Weight, W = mg
uniform motion in a straight line.
Or Differences between Mass and weight
-It is that which makes a body to accelerate. Mass Weight
-It is a push or a pull on a body.
i) S.I unit is kg SI unit is N
Force is a vector quantity. ii) Is a scalar quantity Is a vector quantity
The S.I unit is a newton, N.
iii) Is constant at all places Varies from place to place
Types of forces iv) Is a measure of quantity of Is force of gravity acting
There various types matter in a body on a body.
Gravitational force, weight, friction, upthrust force,
electrostatic force, elastic force, magnetic force, Centripetal
force, centrifugal force, Tensional force, compression force,
shear force etc. 1:3:1:2. FRICTION
Friction is the force which opposes motion.
Gravitational force It acts in the opposite direction to that of the force causing
The earth is surrounded by gravitational field which exerts a motion.
force on anybody in the field. Reaction,R

The strength of the gravitational field is the force acting on a Direction

Frictional
unit mass in the earth’s field. Experimental measurements of motion
force
show that on a unit mass on the earth’s surface, a mass of
1kg experiences a force of 0.9 N i.e. its weight is 9.8N so
the earth’s field strength “g” =9.8N/kg =10N/kg
Weight,W
1kg =10N
g = 10N/kg = 10m/s
Types of friction
Free fall is a vertical motion whose acceleration is due to These are:
gravity “g” = 10m/s2. The gravitational force is towards the a) Static friction b) Sliding or dynamic friction
centre of the earth and its magnitude on the body of mass c) Viscosity
“m” is given by mg.
a) Static Friction:
1:3:1:1WEIGHT Is friction which opposes motion between two surfaces in
Weight of a body is the force of gravity on the body. or The contact at rest.
gravitational force acting on a body. Or  It prevents motion.

Is the force a body exerts on anything which freely supports Experiment for measurement of static friction
it in the gravitational field.

©[email protected] 13
 Reaction,R Experiment for measurement of static friction

Direction
Frictional Reaction,R
of motion
force,F Direction
Added Frictional of motion
weights force,F
Weight,W Added
Scale weights
Pan
Weight,W
i) Adding weight on pan Scale
Know weights are added to the scale pan until the block Pan
moves with a uniform velocity. i) Adding weight on pan
Known weights are added to the scale pan and a small push
ii) The above will occur when weight of scale pan + weights is given each time until the block move with a uniform
on the pan (loads) = maximum friction, F. This maximum velocity.
friction is called limiting friction.
ii) The above will occur when weight of scale pan + weights
iii) Repeating on the pan (loads) = maximum friction, F. This maximum
The procedure is repeated by increasing weight of the block friction is called limiting friction.
“W” and obtaining the corresponding “F”
iii) Repeating
iv) Plotting a graph The procedure is repeated by increasing weight of the block
A graph of F against W (= normal reaction “R”) is plotted “W” and obtaining the corresponding frictional force F’.
.and its slope = coefficient of static friction 𝛍..
iv) Plotting a graph
F (N)
A graph of “F” against R is plotted and its slope =
∆𝐹 coefficient of sliding friction 𝛍..
𝑆𝑙𝑜𝑝𝑒, = =𝛍
∆𝑅
F (N)

∆𝐹
R (N) Slope, = =𝛍
∆𝑅
Frictional coefficient Normal
( )=( )×( )
force, F of friction, μ Reaction, R
F = μR R (N)

Thus Coefficient of static friction μ is the ratio of limiting c) Viscosity:

F
frictional force F to the normal reaction R. i.e μ = Is the opposition to the relative motion between layers of a
R
Note: Coefficient of friction μ has no units. fluid.

Advantages of friction
Example
i) It enables bodies to come to rest
Calculate the static friction when a body of mass 6kg rests
ii) It enables bodies to move without sliding
on a surface; given that coefficient of friction of surface is
iii) It helps in writing
0.5.
iv) It helps in making fire
Given: m= 6kg; μ = 0.5; g = 10ms-2
From; Frictional force, F = μR
Disadvantages of friction
But R = W = mg
i) causes unnecessary heat
= 6(10)
ii) reduces the efficiency of machines
R = 60N iii) Causes things like tyres, soles of shoes to wear
out.
Then From; F = μR iv) Causes parts of machines to break.
F = 0.5(60) v) Causes un necessary noise
F=
30N Reduction of friction
i) Lubrication using oil or grease
b) Sliding or kinetic or dynamic friction: ii) Using ball bearings or rollers
Is friction which opposes relative motion between two
surfaces in contact and in motion. Laws of friction
It is the force which opposes the motion of one surface -The limiting does not depend on the surface area in contact
moving with uniform velocity over another surface. but depends on the nature of the face contact.
 It slows down motion. -Frictional force is not affected by velocity with which a
body moves for sliding friction.

©[email protected] 14
-Friction always opposes motion
-Limiting friction is proportional to normal reaction which is 1:4. PARTICULATE NATURE OF MATTER
equal and opposite to the weight of the body.
-Friction always increases from zero to maximum value MATTER:
called limiting friction. Matter is anything that occupies space and has weight.

States of matter:
Exercise There are three states of matter namely:
1. Two forces of 7N and 9N act perpendicularly on a body  Solids → e.g stone, ice, e.t.c
of mass 2kg. Find the acceleration of the body.  Liquids → e.g water, paraffin, e.t.c
 Gases → e.g oxygen, nitrogen, e.t.c
2. A man starts from point A and walks a distance of 20m
due north and then 15m due east. Find his new position Property Solids Liquids Gases
relative to A. 1. Closely Fairly closely Far apart
Arrangeme packed in packed in from each
3. A parachutist falling with a constant velocity of 16 ms-1 nt of regular pattern regular other.
is blown by wind horizontally at 12 ms-1. molecules. called lattice pattern
(i) Find the resultant velocity of the parachutist.
(ii) If the parachutist jumps from a height of 500m directly
above a ground target, find the horizontal distance by which
the parachutist will miss the target on landing. 2.Intermole Strong Weak Very
cular weak
4. forces.
UNEB 1999 Qn. 7 UNEB 1987 Qn. 23 3. Motion Vibrate within Vibrate with Move
UNEB 2003 Qn. 2 , 27, 41 UNEB 1988 Qn. 23 of the fixed position greater randomly
UNEB 2005 Qn. 12 UNEB 1991 Qn. 24 molecules. amplitude throughou
UNEB 1998 Qn. 2, Qn 18 UNEB 1992 Qn. 34 t the
and Qn. 1 Section B container,
UNEB 2007 Qn. 1, 3 and at greater
Qn11 speed
Friction: 4.Shape Have definite No definite No
UNEB 1997 Qn. 1, 27, and Qn. 1 Section B shape shape. definite
UNEB 1994 Qn. Take shape of shape.
container
5.Rate of Very low in Low High
diffusion some solids
6.Compress Incompressible Incompressibl Compressi
ibility e ble
Note:
 Solids and liquids are incompressible, meaning that
their volumes cannot be reduced by squeezing
them.
 Gases are compressible because of the large spaces
between their molecules.

Change of state
 Heating of matter
When a solid is heated, it changes to a liquid at constant
temperature called melting point. The process is called
melting or fusion.
When the liquid formed is heated further, the liquid changes
to vapour at constant temperature called boiling point. The
process is called boiling or evaporation.

 Cooling of matter
When a gas or vapour is cooled, it condenses to a liquid at
constant temperature called freezing point. The process is
called condensation or liquefying.
When the liquid formed is cooled further, it changes to a
solid at constant temperature called freezing point. The
process is called freezing or solidifying.

©[email protected] 15
  When the temperature of the smoke cell is increased,
Evaporating
Melting smoke particles are seen moving faster and when it is
Solid Liquid Gas reduced, they are seen moving slowly.
 Increase in temperature increases the kinetic energy of
Freezing Condensing the molecules, hence they move faster than before.
 Decrease in temperature decreases the kinetic energy of
Kinetic Theory of matter the molecules, hence they move slowly.
The kinetic theory of matter states that:
 Matter is made up of small particles called molecules or (ii) Size and density of the particles
atoms that are in a state of constant random motion.  When the size of the particles is increased, Brownian
 The speed of motion of the particles is directly motion is reduced and when the size of particles is
proportional to the temperature. reduced, Brownian motion increases.

The kinetic theory of matter can be proved by using: DIFFUSION

(i) Brownian motion Diffusion is the spreading (or flow) of molecules a
(ii) Diffusion substance from a region of high concentration to a region of
low concentration.
BROWNIAN MOTION
Brownian motion is the constant random (or haphazard) Diffusion in liquids:
movement of tiny particles in fluids. Experiment to show diffusion in liquids

Experiment to demonstrate Brownian motion Drinking straw or

Experiment 1: Using Pollen grains. Thistle funnel
 When pollen grains molecules are dropped in water or
suspended in water and observed through a microscope, Glass trough
 The molecules will be seen making irregular
movements in random directions.
 This shows that particles of matter are ever in a state of Water
constant random motion.
Potassium
permanganate
Experiment 2: Using Smoke particles in air. crystal
Procedures:

Microscope  Water is placed in a clean glass trough

 A crystal of potassium permanganate is then introduced
Glass slide at the bottom using a drinking straw.

Air molecules Observation:

(Invisible)  The purple crystal of potassium permanganate dissolves
and spreads throughout the water forming a purple
Glass solution.
cell
Glass rod (lens) Conclusion:
Pollen grain or smoke  This means that potassium permanganate has diffused
Source of light (lamp) particle (Visible) through the water in the glass trough.

 Smoke is placed in a glass cell and the glass cell Diffusion in gasses:
illuminated with light from one side. Experiment to show diffusion in gases
 The smoke particles are then observed from above
using a microscope. 1m long glass tube

Observation:
 White specks of smoke particles will be seen moving in
a constant random motion.
Cotton wool
 This shows that particles of matter are ever in a state of Cotton wool White fumes
constant random motion. soaked in aqueous of ammonium Soaked in
ammonia chloride gas Concentrated
Explanation: HCl acid
The constant random motion is due to un even collision (or Procedures:
bombardment) of the invisible air molecules with the visible  Cotton wool soaked in aqueous ammonia is placed at
pollen grains or smoke particles. one end and another cotton wool soaked in concentrated
hydrochloric acid is placed at the other end of a glass
Factors that affect Brownian motion tube of about 1m long.
(i) Temperature

©[email protected] 16
Observation:
 White fumes of ammonium chloride forms inside the PROPERTIES OF MATTER
tube near the end with cotton wool soaked in HCl acid. (a) MOLECULAR PROPERTIES OF MATTER
Molecular properties of matter are based on the behavior of
Conclusion: the molecules. These are observed in the following;
 This means that: (i) Diffusion
(i) The gases have diffused through the air in the tube. (ii) Molecular forces
(ii) Ammonia diffuses faster than Hydrogen chloride. (iii) Capillarity
(iv) Surface tension
Note: Alternatively; (v) Elasticity
An air molecule tube is inverted over brown nitrogen
dioxide molecules tube. Molecular forces:
Observation: the brown colour spreads into the upper tube at Intermolecular forces are forces of attraction or repulsion
the same time the air molecules spread into the lower tube. between molecules of matter. The molecules may be of the
same substance or of different substance.
Experiment II: to show diffusion in gases Types of molecular forces

 Cohesion (or Cohesive) force

Hydrogen Cohesion is the force of attraction between molecules of the
gas same kind or same substance.
E.g Forces between water molecules themselves, forces
between mercury molecules themselves e.t.c.

Porous pot Water  Adhesion (or Adhesive) force

Air Adhesion is the force of attraction between molecules of
different kinds or different substances.
E.g Forces between water molecules and glass molecules,
forces between mercury molecules and glass molecules,
Manometer forces between water molecules and mercury molecules,
e.t.c.
 Connect a water manometer to a porous pot containing
air. NOTE: The magnitude of the cohesion and adhesion forces
 Pass hydrogen into the air enclosed in the porous determines the:
material as shown in the diagram above.  Shape of liquid meniscus in contact with a solid
 The water level in the left arm of the manometer falls  Ability of the liquid to wet a substance
while that in the right arm rises.  Rise or fall in a capillary tube.
 The hydrogen molecules diffuse through the porous
material into the air. This increases the pressure in the When cohesion is greater than adhesion forces, e.g mercury
porous pot, which then acts on the water surface in the and glass, then the liquid;
left arm of the manometer, thus pushing the water level (i) Does not wet glass
down wards. (ii) Forms spherical balls when spilled on a glass
surface
Factors that determine the rate of diffusion (iii) Depresses in a capillary tube
(i) Size of diffusing molecules (iv) Meniscus curves downwards.
Smaller molecules diffuse faster than larger molecules. This Mercury droplets
is because larger molecules occupy large space than small
ones. Glass

(ii) Temperature
The rate of diffusion is directly proportional to temperature. When adhesion is greater than cohesion forces, e.g water
and glass, then the liquid;
(iii) Pressure (i) Wets glass
The rate of diffusion is directly proportional to pressure. (ii) Spreads when spilled on a glass surface
This is because at a higher pressure, gas molecules are (iii) Rises in a capillary tube
squeezed, move faster and collide frequently than at low (iv) Meniscus curves upwards
pressure.
Water drop
(iv) Molecular weight Glass
Lighter molecules diffuse faster than massive molecules.
The speed of diffusion in a gas depends on the speed of
molecules in that; lighter molecules diffuse at greater rate Water spreads on the glass surface due to greater adhesion
e.g. the rate of diffusion of hydrogen gas is faster than that forces between glass and water molecules than the cohesion
of carbon dioxide because the molecules of hydrogen move forces between water molecules themselves hence wetting
at a higher speed since they are lighter than the molecules of the glass.
carbon dioxide.
©[email protected] 17
 CAPILLARITY: Uses of capillarity
Capillarity is the elevation (or rise) or depression (or fall) of  It helps paraffin (fuel) to rise up in wicks of stoves
a liquid a narrow porous medium e.g tube. and lamps.
Capillary action depends on cohesion and adhesion forces.  It helps water to move up tree-trunks to the leaves
 It helps blotting papers to absorb liquids
(i) When adhesion is greater than cohesion forces, e.g NOTE:
water and glass, then :  All the above uses are possible because of greater
 the liquid rises in the capillary tube adhesion forces than cohesion forces between
 the meniscus curves upwards (concave); molecules of the two substances. (i.e Fuel and wick,
 The liquid wets glass water and tree-trunk, liquid and blotting paper
respectively). Thus, the wet part of the solid goes on
Capillary tube increasing upwards.
 Damp proof material e.g polythene is put in the
foundation course of a building to stop capillary action.
Meniscus
This is because bricks, plaster and mortar are porous, so
(Curves upwards)
water can rise up through the narrow pores and weaken
the wall.

Liquid SURFACE TENSION:

(E.g. water) Surface tension is the force acting normally on a one-metre
length of a line drawn on the surface of a liquid. Its S.I unit
is Nm−1 .
(ii) When cohesion is greater than adhesion forces, e.g
Surface tension enables the surface of a liquid to behave like
mercury and glass, then the :
a stretched elastic skin (or membrane).
 liquid falls (or depresses) in the capillary tube It is due to cohesion forces between the liquid molecules.
 the meniscus curves downwards (convex);
 the liquid forms spherical balls when spilled on a Surface tension is the force on the liquid surface that causes
surface it to behave as if it is covered with a thin elastic membrane.
 does not wet glass
Molecular explanation of surface tension:
Capillary tube Unbalanced
surface molecule
Meniscus Liquid
(Curves downwards) surface

Liquid
(E.g. mercury) Resultant
inward force Balanced inner molecule
According to Kinetic theory surface tension is explain as
Effect of size or diameter of the capillary tube on capillarity follow:-
Smaller Molecules on the surface experience a net down word
Capillary tubes force on them and surface of the liquid thus tends to
contract and acquire a state of tension.
Larger  A molecule inside the surface of the liquid is
Capillary tube surrounded by equal number of molecules on all sides.
The intermolecular forces between it and the
surrounding molecules is zero.
Mercury  A molecule on the surface has very few molecules on
the upper side compared to those bellow the liquid
surface.
Water  Thus if this molecule is displaced upwards, a resultant
attractive force due to the large number of molecules
bellow the liquid surface has to be overcome.
 This force is trying to pull the molecule out of the
 Water rises higher in a capillary tube of smaller surface into the bulk. It is trying to make the surface
diameter than the one of a larger diameter. smaller, hence surface tension.
 Mercury depresses deeper in a capillary tube of
smaller diameter than the one of a larger diameter.

©[email protected] 18
Experiment to demonstrate existence of Surface tension  The thickness or size of the oil film is estimated from:
𝐕𝐨𝐥𝐮𝐦𝐞 𝐨𝐟 𝐨𝐢𝐥 𝐝𝐫𝐨𝐩
Thickness of oil drop; t =
𝐀𝐫𝐞𝐚 𝐨𝐟 𝐨𝐢𝐥 𝐩𝐚𝐭𝐜𝐡

𝐕𝐨𝐢𝐥 𝐝𝐫𝐨𝐩
t=
𝐀𝐩𝐚𝐭𝐜𝐡
NOTE:
It is a common procedure to;
 Dissolve a known volume of a solute (e.g cooking oil or
Procedures: oleic acid) V1 in a known volume of a solvent (e.g
 A clean beaker is filled with water. Petroleum, alcohol or ether) V2 to form a solute-solvent
 A blotting paper is placed on the surface of the water. solution.
 A pin or needle is gently placed on the blotting papper  Then a known volume, V3 of the solute-solvent solution
and observed. is dropped onto the water surface covered with
lycopodium powder.
Observation:  The solvent in the drop either dissolves in water or
 After some few minutes, the blotting paper absorbs evaporates and the solute (oil) spreads forming a
water and sinks to the bottom. cylindrical oil film with a circular patch, whose
 The needle remains floating on the water surface. diameter ‘’d’’ is measured.
 The thickness or size of the oil film is estimated from:
Conclusion:
 The needle is held by surface tension. 𝐕𝐨𝐥𝐮𝐦𝐞 𝐨𝐟 𝐨𝐢𝐥 𝐢𝐧 𝐭𝐡𝐞
Volume of cylindrical film = ( )
𝐬𝐩𝐡𝐞𝐫𝐢𝐜𝐚𝐥 𝐝𝐫𝐨𝐩
Effects of surface tension Area of Patch × Thickness (t) = Volume of oil
(i) A needle (pin) floats on water surface.
𝐕𝐨𝐥𝐮𝐦𝐞 𝐨𝐟 𝐨𝐢𝐥 𝐝𝐫𝐨𝐩
(ii) Tents keep water, umbrellas and raincoats keep water Thickness of oil drop; t =
off due to surface tension. 𝐀𝐫𝐞𝐚 𝐨𝐟 𝐨𝐢𝐥 𝐩𝐚𝐭𝐜𝐡
(iii) Insects e.g pond skater can walk across a water surface.
(iv) Water drops from a tap form spherical shapes. This is However, the volume of the oil in the solution which forms
because; a free falling drop will take the shape that has the oil film is calculated as follows:
the least (minimum) area. (V1+V2) of solution =(contains) (V1) of solute or oil

Factors affecting surface tension (V3) of solution dropped V

(i) Temperature: Increase in temperature (or heating a =(contains) (volume of oil in drop)
liquid) weakens or reduces surface tension. (V1 + V2 ) × V = V3 × V1
(ii) Impurities: Impurities such as detergents, soap solution,
alcohol e.t.c reduce surface tension. V1 V3
V=
(V1 + V2 )
Estimating the thickness (or Size) of an oil molecule: 𝐕𝟏 𝐕𝟑
Volume of oil in drop , 𝐕 =
A drop of oil is able to spread into a thin film of a large area (𝐕𝟏 +𝐕𝟐 )

when placed on a clean water surface. This is because the

end of the oil molecule has greater adhesion forces than Assumption
cohesion forces for neighboring molecules. (i) All the solvent has evaporated or dissolved in water.
The size of an oil molecule is too small to be accurately (ii) The oil patch is circular.
measured. Its approximate size can only be estimated using (ii) The oil film or molecule formed is cylindrical.
an experiment. (iii) The oil film formed is one molecule thick. (i.e the
spaces between the molecules in the oil film are assumed to
Experiment to estimate the size of an oil molecule be negligible).
. (iii) The oil drop is spherical.
(iv) Volume of cylindrical film=Volume of oil in spherical drop

NOTE:
The water surface should be sprinkled with lycopodium
powder so that:
(i) The film becomes stationary.
(ii) A clear circular patch for measuring diameter is formed.

Example 1:
A solution is made by dissolving 1cm3 of cooking oil in
 Fill a clean trough with clean water and sprinkle 1999cm3 of methanol. When 0.004 cm3 of the solution is
lycopodium powder on the surface of the water. dropped on the surface of water, an oil film of diameter
 Drop a known volume, Vo of the oil onto the water 12cm is obtained.
surface covered with lycopodium powder. (i) Calculate the volume of cooking oil in the film.
 The oil spreads forming a cylindrical oil film with a (ii) Estimate the thickness of a molecule of cooking oil.
circular patch, whose diameter ‘’d’’ is measured.
©[email protected] 19
(iii) State any two assumptions made in (i) above. An oil drop of volume 1x10-9 m3 spreads on a water surface
Solution: to form a patch of area 5x10-2 m2. If the patch is one
Volume of solute or oil, (V1) = 1cm3 molecule thick, find the approximate number of molecules
Volume of solvent (methanol), (V2) = 1999cm3 in the drop.
Volume of solution dropped, (V3) = 0.004cm3
Volume of solute or oil, in V3 = V Solution:
Volume of oil in drop , V = 1x10−9 m3
V1 V3 1×(0.004)
Volume of oil in drop , V = = Area of oil patch, A = πR2
(V1 +V2 ) (1+1999)
A = 5 × 10−2 m2
0.004
V= Then, from A × t = V
(2000) (5 × 10−2 m2 ) × t =1x10−9 m3
1x10−9 m3
Volume of oil in drop , V = 0.000002 cm3 t=
5×10−2 m2
t = 2 × 10−8 m
Alternatively:
Volumes NOTE: Remember the oil drop is spherical thus its radius, r
𝑡
Volume of Solution Volume of Oil is equal to half the thickness, of the oil film.
2
2000 cm3 1 cm3 Thus the radius of the spherical oil drop, r is given by;,
0.004 cm3 V t 2×10-8
r= = = 1×10-8 m
2 2
2000V = 1 × 0.004 If n is the number of molecules in the oil drop, then
V = 0.000002 cm3 𝑡
n (volume of sphere of radius, ) =(volume of oil drop)
2
4
Area of oil patch, = 𝜋𝑅2 𝑛 ( π𝑟 3 ) = 1x10−9
3
12 4
= 𝜋( )2 𝑛 { × 3.14 × ( 1 × 10−8 )3 } = 1x10−9
3
2
= 3.14 × 36
Area of oil patch, 𝐴 = 113.097cm2 𝑛(4.189 × 10−24 ) = 1x10−9
1 x 10−9
𝑛=
4.189×10−24

Volume of oil drop 𝑛 =2.39 x 1014 molecules.

Thickness of oil drop; t =
Area of oil patch
Exercise
0.000002 1. In an experiment to estimate the size of an oil molecule,
t=
113.097 a volume of 0.12cm3 was placed on a clean surface and
Thickness of oil drop; t = 1.76 × 10−8 cm spread into a patch of area 0.0006cm2. Calculate the
size of the oil molecule. (𝐴𝑛𝑠:t =200 cm).
Example 2:
In an oil film, experiment to estimate the size of a molecule 2. When 0.002 cm3 of oil was dropped on the surface of
0.005cm3 of oleic acid was dropped on lycopodium powder water, an oil film of diameter 6.0cm was formed.
on a water surface. The mean diameter of the acid was 5cm. Calculate the thickness of the film.
Calculate the thickness of a molecule of oleic acid. (𝐴𝑛𝑠:t =7.08 × 10−5 cm).

Solution: 3. The volume of 100 drops of certain oil is 1.0cm3. One

Volume of solute or oleic acid, (V1) = 0.005cm3 such drop was placed on a water surface and it spread
Volume of oil in drop , V = 0.005 cm3 into a circular patch of average diameter 50cm. What is
the size of the oil molecule?
Area of oil patch, = πR2 (𝐴𝑛𝑠:t =5.09 × 10−6 cm).
5
= π( )2
2 4. If 1.8x10-4cm3 oil spreads to form a patch of area 150
= 3.14 × 6.25 cm2. Determine the thickness of the patch.
Area of oil patch, A= 19.63cm2 (𝐴𝑛𝑠: t =1.2 × 10−6 cm).

Then, from A × t = V 5. A drop of oil of diameter 0.5mm becomes a circular

Volume of oil drop(V) film of oil of diameter 30cm.
Thickness of oil drop; t =
Area of oil patch(A) (i) Find the thickness of the oil film.
(𝐴𝑛𝑠:t =9.2 × 10−10 m).
0.005
t= (ii) Calculate the number of molecules in the oil
19.63
Thickness of oil drop; t = 2.55 × 10−4 cm drop. (𝐴𝑛𝑠:n =1.6 × 1017 molecules).

Example 3:

©[email protected] 20
6. 1cm3 of oleic acid was dissolved in 99 cm3 of alcohol to Stiffness (toughness): Is the ability of a material to resist
form 100 cm3 of solution. A 1-cm3 drop of the solution bending or to resist forces, which try to change its shape or
was put on a water surface sprinkled with lycopodium size so that it is not flexible. A material which is more stiff
powder. The alcohol dissolved in water leaving the acid always needs a large force in order to bend e.g. wood is
which spread to form a patch of diameter 14 cm3. more stiff than rubber.
(i) Explain why lycopodium powder was used
(ii) Calculate the volume of the acid in the 1-cm3 Ductility: Is the ability of a material to deform when a force
drop of the solution. is applied.
(iii) Estimate the size of oleic acid molecule. Is the ability of a material to be
changed/rolled/hammered/pressed/bent or stretched into
7. In an experiment to determine the thickness of an oil other shapes with out breaking.
molecules the following were done; Ductile materials can be hammered, bent or drawn into
 1cm3 of oil was dissolved in 99cm3 of ether and various shapes with out breaking.
1cm3 of the solution was diluted to 200cm3 A Ductile material is one, which stretches elastically then
 0.4 cm3 of the dilute solution was dropped onto the plastically before it breaks when tensile force acts on it
surface of water.
 The diameter of film formed was found to be 7cm. Examples;
from the above. Calculate the thickness of the oil  Wet clay, plasticine, Metals, steel, e.t.c.
molecules. (𝐴𝑛𝑠:t =5.19 × 10−7 cm).
Properties of ductile material.
8. A solution was made by dissolving 1cm3 of cooking oil i) can be molded into any shape.
in 199cm3 of methanol. When 0.004cm3 of the solution ii) can be bent without breaking. Because of the above
was dropped onto the water surface, an oil film of properties of ductile materials, they can be rolled into sheets
diameter 12cm was obtained. Find the thickness of the drawn into wires or worked into other useful shapes without
oil molecule. breaking.

9. See UNEB Brittleness: Is the ability of a material to break suddenly

1987 Qn.36 and Qn.7 1987 Qn.2 without bending.
1997 Qn.13 2001 Qn.43 A brittle material is one, which bends very little, then
1999 Qn.13 2003 Qn.3 suddenly cracks without undergoing plastic deformation.
2006 Qn.19 2005 Qn.49 When a brittle material breaks, its pieces fit together almost
1992 Qn.31 1993 Qn.7 exactly and can be glued back.
2007 Qn.25 2002 Qn.45
Properties of brittle material
i) Can bend very little and suddenly break without
(b) MECHANICAL PROPERTIES OF undergoing plactic deformation.
MATTER ii) Cannot be molded into any shape.

Mechanical properties of matter are the behavior of matter Examples;

under action of an external force.  Glass, chalk, stones, concrete, cast iron bricks, alloys
like brass, and bronze.
Materials are things used in the construction of structures
like buildings bridges, dams, etc. Before a material is put to Elasticity: Is the ability of a material to recover its original
use the following mechanical properties should be shape and size after a deformation force has been removed.
considered; strength, stiffness, ductility, brittleness and
elasticity. The material stretches due to the particle being pulled
further apart from one another.
Strength: It is the ability of a material to resist forces that A material, which does not recover its original shape and
want to deform it. size but is deformed permanently, is plastic.
Is the ability of a material to resist breaking when stretched,
compressed or sheared. Examples;
Force  Rubber, steel, e.t.c.
Braking stress =
Cross − sectional area
Hooke’s law:
The strength depends on Hook’s law states that the extension of a material is directly
i) Dimensions of the material, in that a large force is applied proportional to the applied force provided the elastic limit is
in order to bend a material of large diameter. not exceeded.
i.e. the material returns to its original length when the
ii) Nature of the substance stretching force is removed, provide the elastic limit is not
Materials of same size but of different substance require exceed
different force to be broken. E.g. a large force is applied to a
steel rod compared to a piece of wood of the same size. In short:𝐅𝐨𝐫𝐜𝐞 ∝ 𝐞𝐱𝐭𝐞𝐧𝐬𝐢𝐨𝐧
𝐅𝐨𝐫𝐜𝐞 = 𝐤(𝐞𝐱𝐭𝐞𝐧𝐬𝐢𝐨𝐧)
iii) Magnitude of force applied 𝐅 = 𝐤𝐞

©[email protected] 21
Where k is the proportionality constant or material constant
in Nm-1, Where, F is the stretching force in newtons and e is
the extension in metres. Experiment to verify Hook’s law.
Extension, e = New length − Original length
𝒆 = 𝒍𝒏 − 𝒍𝒐 .
- Metre rule
It is also important to note that; -
F1 F2 F 1 e1
= Or = -
e1 e2 F 2 e2 -
Where F1 is stretching force producing extension e1 and -
F2 is stretching force producing extension e2 on the same -
material. -
-
Example1: - Spring
A spring is stretched by 0.05m by a weight of 5N hung from -
one end. - Pointer
(i) What weight will stretch it by 0.03m? -
(ii) Determine the spring constant. 50g -

Solution:
Given;e1 =0.05m,e2 =0.03m, k=?, F1 =5N, F2 =?.

Then from; 5
F1 F2 F2 = × 0.03  Original length of the spring lo is noted.
= 0.05
e1 e2  Then various loads are suspended on the spring and the
F2 = 3N corresponding new length, ln of spring for each is noted.
5 F2  The extension, e produced is calculated from;
= Extension, 𝒆 = 𝒍𝒏 − 𝒍𝒐
0.05 0.03
 The readings are noted in a table below.
Load(N) 𝒍𝒏 (m) e(m)
- - -
Example 2:
- - -
A spring increases its length from 20 cm to 25cm when a
force is applied. If the spring is constant is 100N/m.
Calculate the force.  A graph of load against extension is drawn, and a
straight-line graph is obtained whose slope is equal to
Solution: the spring constant.
Given;lo =20cm,ln =25cm, k=100Nm-1 .

𝑒 = 𝑙𝑛 − 𝑙𝑜 . From Hooke’s law; Load (N)

e = 25 − 20 F = ke
e = 5cm F = 100(0.05) Slope, = spring
5 F = 5N
e= = 0.05m Constant, k
100

Exercise:
1. A vertical spring of length 30 cm is stretched to 36 cm
when an object of mass 100g is place in the pan O Extension (m)
attached to it. The spring is stretched to 40 cm when a
mass of 200g is placed in the pan. Find the mass of the
 Thus, the load is directly proportional to the extension
pan.
“e”. This verifies Hooke’s law.
2. A force of 500N extends a wire by 2mm. If the force is
A graph of load against extension
reduced by a half, what will be the new length of the
wire, if the original length is 10cm.

3. A spring constant of natural length 8.0 × 10−2 m

extends by 2.5 × 10−2 mm when a weight of 10N is
suspended on it.
(i) Find the spring constant.
(ii) Determine the extension when a weight of 15N
is suspended on the spring

©[email protected] 22
 stress F 𝑙𝑜
Young's modulus= =
strain 𝐴𝑒
Note: This holds only when the elastic limit of a material is
Load (N) D not exceeded.
B E
A Example 3:
A wire of cross section area 3m2 increases in length from
C 20cm to 25cm, when a force of 5N is applied. Calculate the;
(i) tensile strain.
(ii) tensile stress
(iii) Young’s modulus.
A = Proportionality
O limit
P Extension (m)
B = Elastic limit
C = Yield point (minimum stress) Solution:
D = Hecking point (maximum stress) (i) Given;lo =20cm,ln =25cm, F=5N, A = 3𝑚2
E = Breaking point 𝑒 = 𝑙𝑛 − 𝑙𝑜 ⟺ e = (25 − 20) = 5cm
OP = Permanent deformation 5
e= = 0.05m
100
Explanation (i)
Along OB, the load is proportional to extension in that the e (iii)
Tensile train=
extension increases as the load increases. 𝑙𝑜 stress
Point “B” is called elastic limit. Young's modulus=
strain
5
Tensile train= = 0.25 1.67
Beyond B (elastic limit), the graph is not a straight line 20 Young's modulus=
meaning that extension is no longer proportional to the load. (ii) 0.25
The material becomes plastic. This is indicated by a kink at F
C, which is called yield point. Tensile stress= Young's modulus=6.67Nm-2
A
5
Beyond C, the material behaves plastically. i.e. it does not Tensile stress=
3
regain its shape and size. Therefore, it undergoes plastic Tensile stress=1.67Nm-2
deformation. This goes on to the breaking point E.
Example 4:
Point D represents the maximum stress (Breaking stress) the Calculate the tensile stress when a force of 25N acts on a
material can withstand fracturing. wire of cross sectional area 5m2.

Explanation of sketch of load against extension Given; A = 5m2, F = 25N

according to kinetic theory
OB the molecules are pulled slightly farther apart but can F
move back to original position when stretching force is Tensile stress =
A
removed. The deformation is called elastic.
25
Beyond C, layers of atoms slip over each other. The Tensile stress=
5
molecule move farther apart but cannot move back to Tensile stress=5Nm−2
original position when stretching force is removed.
Question:
Tensile stress, Tensile strain and Young’s modulus. A metallic solid of mass 45kg rests on a copper rod of cross
sectional area 0.5 cm2 standing vertically as shown below,
Tensile stress:
Is the force acting per cross section area of a material. Its S.I
unit is Nm-2 or Pa.
Force F
Stress= =
Cross section area A

Tensile strain:
Is the ratio of extension to original length of a material. It
has no units.
Extension e
Strain= =
Original length 𝑙𝑜 Calculate the stress in the rod.
A. 9.0 × 102 Nm−2 B. 9.0 × 105 Nm−2
Young’s modulus: C. 9.0 × 106 Nm−2 D. 9.0 × 108 Nm−2
This is the ratio of tensile stress to tensile strain.
It is the gradient of the straight line in the elastic region. Its
S.I unit is Nm-2 or Pa.

©[email protected] 23
CRYSTALS: Some of the common metals are; copper, Zinc, Lead, Tin,
Crystals have hard, flat sides and straight edges. Crystals of Nickel, Chromium. e.t.c
the same substance have the same shape. This will be
observed when salt crystals grow as water evaporates from (b) Alloys:
the salt solution on glass slide as seen through a microscope. Alloys are made by mixing one metal with one or more
other metals and in some cases non metals.
This fact suggests that crystals are made of small particles
called atoms or molecules arranged in orderly way in plates.  Steel alloys. Steel is an alloy of Iron and carbon. Iron is
Metals consist of tiny crystals. alloyed with a variety of the other materials like:-

Tensile, shear and compression force. Examples of steel

(i) Compression force  Mild steel (Iron and carbon) used in making cars, ships
Compression is when the force acts as in the diagram below. etc.
This results in the particles to be pressed more closely  Stainless steel has high corrosion resistance due to its
together. So the length of the material decreases but the composition of chromium and nickel. It is used in
thickness of the material increase. making knives, watch casing etc.
Compressional  Lead and sulphur steel. It is used in the making of
compressional screws because it is easy to cut.
Force, F Force, F
 Duralium is an alloy of aluminium and is used in the
making of aircrafts because of its lightness and strength.
(ii) Tensile force
Tensile force is when the force acts as in the diagram below.  Nickel-Chromium alloys
This result in the particle of the material to be pulled further i) Have good resistance to corrosion
apart from one another. So tensile forces increase the length ii) The electrical conductivity is independent of
of the material but its thickness decreases. temperature
iii) Have a high melting point.
Tensional Tensional
For these properties, nickel-chromium alloys are useful for
Force, F Force, F
making elements of electrical heaters.

Differences between tensile and compression force.  Invar: is a nickel-iron alloy with low expansivity. It can
Tensile force Compression force be used to make accurate measuring tape and parts of
i) Particles are pulled i) Particles are pulled close watches.
further apart together  Brass: Is copper-zinc alloy? It is ductile and with high
ii) Length of the material ii) Length of material tensile strength. It is used in stamping, pressing or
increases decreases drawing. It is used in the making plumbing fittings.
iii) Thickness of the iii) Thickness of the material
material decreases increases  Bronze: Is an alloy of copper and tin is harder and
stronger than brass. It is useful in ornamental work.
(iii) Shear force
Shear force is the force needed to fracture the material in a (c) Stony materials
direction parallel to the applied force in that one section (or  Bricks: Are made by moulding a mixture of clay and
layer) of the material slides over its neighbour. water and beating the mixture strongly.
A shear is produced when two equal but opposite forces are  Concrete: A concrete is a stony material which is a
applied to a body. The effect depends on the turning effect mixture of cement, sand gravel and water. This is left to
or movement of the force. harden in desired form.

Properties of concrete which makes it a suitable building

material
F i) It is resistant to weather
F ii) It is resistant to compression
Body after iii) It is very durable
Application Body after application iv) It is resistant to fire
Of shear force Of shear force
Concrete can be primarily subjected to compression like
Important materials used for construction. column and arches because it compression strength is high.
(a) Metals: However, concrete is relatively brittle material whose tensile
Large varieties of metals are available from which different strength is small compared to its compressional strength.
alloys or combinations of these metals are made into various This makes concrete unsuitable for use in structure
shapes. Metal can be rolled, pressed, and drawn, and are membranes which are subjected to tension like tie rods,
usually strong, rigid and elastic. beam.

©[email protected] 24
In order to overcome the limitation of low tensile strength, BEAMS AND STRUCTURES
steel (with high tensile strength) is interlocked and A beam is a large and long straight piece of materials with
completely surrounded by hardened concrete mass to form uniform cross-sectional area.
integral part of the membranes called reinforced concrete.
A girder is a small piece of material used to strengthen a
Reinforced concrete is a combination of steel rods, Cement, beam.
sand, gravel and water.
A beam is the simplest but one of the most important
Concrete is reinforced by interlocking and surrounding the structures. When a beam bends, one side is compressed, the
steel rods with the hardened concrete mass. other is stretched (tensile) and the centre is unstretched
neutral plane.
Advantages of reinforced concrete. B C
i) It has high compressive strength
ii) It has high tensile strength O A
iii) It has much greater ductility D E
iv) It is tough
Above is the diagram of rubber marked with lines as shown.
v) It is weather and fire resistant
When the rubber is bent as shown below,
However, the disadvantage of concrete is its volume
instability caused by shrinkage of concrete, which results in Tensional Force.
cracks.

The cracks can be filled with mixture of special tar, sand,

cement and water. B C
O A
Cement Mortar: Cement mortar is composed of sand,
cement mixed with water and left to harden. D E
Neutral Compressional
axis. Force
Reinforcement: sisal-fibre, bamboo stripes, wood strands are
also used in reinforcing concrete and cement mortars.
The lines above OA move further apart. Showing that the
The reinforcing improves on tensive strength and weather above parts are in tension.
resistance of the materials.
The lines below OA move closer showing that the below
Glass: Glass can be melted and formed into various shapes. part are in compression.

Advantages of glass which makes it useful as construction Along OA the lines are at the same distance apart as before
material. implying neutral axis.
i) It is transparent
ii) Its surface quite harder From above it can be noted that materials from neutral plane
iii) Very few chemicals react with glass. can withstand compression and tensile force due to loading.
iv) Can be melted and formed into various desired
shapes.
Flange
Safety glass: Is used motor vehicle windscreen safely glass
is made by heating plate glass cooling the two surfaces in a
stream of air. Hollow
Section Pipe
These contract and compress the glass in the middle H or I - beam
resulting a very strong glass which when hit hard enough The top and bottom flanges have the shape shown.
breaks into small fragment that are less dangerous than large
pieces. Because they are beams that have had material removed
from the neutral plane, so can with stand compression and
Wood: Wood is a poor conductor of both heat and tensile forces due to loading.
electricity.
The hardness and strength of wood varies from one sample In general, pipes for construction of structures like bicycles,
to another. bridges are made hollow for the following advantages.
 They are beams that have had materials removed
Thin sheets of wood are glued together to form a laminate
from the neutral plane so can withstand tensile and
(plywood) which is stronger than solid wood of the same
compression forces.
thickness.
 Notches cannot spread easily hence less risk of
breaking.
 Less material is used for construction
 The finished structure is lighter
©[email protected] 25
  Provide room for expansion and contraction. STRUCTURES:
A structure is rigid meaning that it can support weight.
The Notch effect:
Cracks and fractures: Triangular structures are more rigid than others. So a
A notch is a cut or weak point in the surface of a material. rectangular structure can be made rigid by adding a diagonal
piece so that the rectangular change into two a triangular
When a notch is made in the reinforcing material, the fibres, structure, which are more rigid. This is why doors, water
stripes and strands in the length of concrete or mortar are tanks and roofing tuffs are made with triangular shapes.
broken down.
This result in such materials to fail to withstand compression Triangular
or tensile force. shapes
Neutral
axis.

Roofing tuff
Tensional Notch Tensional Water tank
Force. spreads Force.
Struts and Ties
B C In any structure, there are parts, which are under action of
O A tensional forces and others under action of compressional
forces.
D E
Notch Neutral Ties are girders, which are under tension.
closes axis. This occurs when a girder results in the points it joins to
Glass tubes are easily broken after notch is made on the moves further apart on the removal of such girder in a tie.
side.
Properties of ties:
A notch, crack or scratch on the surface of brittle material  It is under tension
like concrete and glass, spreads more readily under tensile  When removed, the point it joins move further
force than under compression. apart.
 It can be replaced by a rope or strong string.
Reducing notch effect:
(a) For concrete and cement mortar; Struts are girders, which are under compression.
Notch effect can be reduced by; pre-stressed concrete This occurs when a girder result in the point to move closer
containing steel rods that are in tension because they were together on removal girder in struts.
stretched while the concrete was poured on them.
Properties of struts:
This is advantageous in that as well as resisting tension  It is under compression
forces they keep the concrete in concrete in compression  When removed, the point it joins move closer to
even if the whole structure is not. each other.
 It cannot be replaced by a rope or strong string.
(b) For glass: B C
Notches can be removed from glass
i) By making the surface of glass as smooth as possible. So
glass usually making smooth to reduce the breaking due
to notches. A D
E
ii) For safety glass used in motor vehicle screen is made by
heating plate glass and cooling the two surfaces in a
stream of air where they contract and compress the glass
in the middle. This is called thermal toughening.
iii) By reinforcing glass with transparent polythene. In order to determine each of the girders whether its a tie or
a strut, each of the girders is removed and the effect is
(c) For wood; noted.
Thin sheet of wood are glued together to form a laminated  If the points move further apart then the girder is tie and
structure which is able to resist notches more than solids if the points move closer together then the girder is
because for solid structures, the crack or a notch goes right strut.
through while in a laminated structure it may be stopped by  When BC is removed, point B moves close to point C
one of the layers. showing that girder BC is strut.
 When AB is removed, point A moves close to B. so
girder AB is strut.
 When AE is removed, point A moves further apart from
E meaning that girder AE is tie. Similarly, girder ED is
tie.

©[email protected] 26
For structures A: reinforced B: in tension
When BE is removes point B move further apart from E C: pre stressed D: in compression
meaning the girder BE tie.
4. see UNEB
F B C
1993 Qn.10 and Qn. 26 2007 Qn. 40
CD is a tie 1997 Qn.19 1987 Qn. 9
BF is a tie 1989 Qn. 10 1990 Qn. 5
1994 Qn. 4 1994 Qn. 5
G A BC is a tie 1996 Qn. 21 2002 Qn.47
D
E CE is a strut 2006 Qn. 8
AD is a strut
DE is a strut
Load AE is a strut

When BF is removed, the structure turns about point G. B

will move further away from F hence BF is a tie.
When BC is removed, the structure will bend at E. Thus, C
will move in the direction of the load, far away from B. This
means BC is under tension and hence it is a tie.

When CD is removed, point D moves down wards with the

load. Point D moves away from C, so CD is a tie.

When DE is removed, CD will be vertical due to the load.

Thus, point D moves nearer to E meaning that girder DE is a
strut. Similarly, girder EG is a strut.

When CE is removed, the load moves down wards and part

BCD will be straight due to the load. Thus, point C moves
nearer to E meaning that girder CE is a strut. Similarly,
girders BE and AB are struts.

Exercise:
1. Roofing structures and many bridges are made designed
triangular sections to;
(i) Minimize the material used
(ii) Withstand compression forces
(iii) Minimize tensile force under compression.
A. (ii) only B.(ii) and (iii) only.
C. (i) and (iii) only. D. (i) , (ii) and (iii)

2. The beam shown below is being acted upon by forces

F1 and F2 as shown.

The regions P, Q and R are respectively,

A. tension, compression, neutral axis
B. neutral axis, compression, tension
C. tension, neutral axis, compression
D. compression, neutral axis, tension

3. A notch on a material spreads more rapidly when the

material is;

©[email protected] 27
 From above, it can be noted that:
1:5. TURNING EFFECT OF FORCE  The greater turning effect of a force occurs when the
(MOMENTS) force acts on an object at a right angle.
Moment of a force is also called the measure of the turning  It is easier to close the door by pushing it at a point as
effect of a force. far away from the hinges as possible. Because the force
applied can easily balance with the reaction at the
Moment of a force is a product of a force and the hinges.
perpendicular distance of the line of action of the force from
the fulcrum (pivot). Factors affecting moments
The moment of the force depends on the:-
𝐌𝐨𝐦𝐞𝐧𝐭 𝐨𝐟 i) magnitude of a force
( ) = Force ×
𝐚 𝐟𝐨𝐫𝐜𝐞 ii) Perpendicular distance from the turning point
𝐏𝐞𝐫𝐩𝐞𝐧𝐝𝐢𝐜𝐮𝐥𝐚𝐫 𝐝𝐢𝐬𝐭𝐚𝐧𝐜𝐞 𝐨𝐟 (fulcrum).
( 𝐭𝐡𝐞 𝐥𝐢𝐧𝐞 𝐨𝐟 𝐚𝐜𝐭𝐢𝐨𝐧 𝐨𝐟 𝐭𝐡𝐞 )
𝐟𝐨𝐫𝐜𝐞 𝐟𝐫𝐨𝐦 𝐭𝐡𝐞 𝐩𝐢𝐯𝐨𝐭 Law or principle of moments
This states that when body is in a state of equilibrium the
sum of clockwise moments about any point is equal to the
SI unit of moment is a newton meter (Nm). Moment of a sum anticlockwise moments about the same point.
force is a vector quantity. 𝐒𝐮𝐦 𝐨𝐟 𝐜𝐥𝐨𝐜𝐤𝐰𝐢𝐬𝐞 𝐒𝐮𝐦 𝐨𝐟 𝐚𝐧𝐭𝐢𝐜𝐥𝐨𝐜𝐤𝐰𝐢𝐬𝐞
( ) = ( )
Examples of the turning effects of a force; 𝐦𝐨𝐦𝐞𝐧𝐭𝐬 𝐦𝐨𝐦𝐞𝐧𝐭𝐬
 Opening or closing a door
 Children playing on a see-saw Experiment to verify the principle of moments.
 Bending of the fore arm of a hand Fulcrum d2
d1
Example;1
A force of 12N is applied to open a door handle, which is m1 m2
0.8m from the hinges of the door. Calculate the moment of
the force produced. W1= W2

The metre rule is balanced horizontally on a knife-edge and

Frame Frame its centre of gravity, G noted.

0.8m Un equal masses m1 and m2 are hung from cotton loops on

either sides of the rule.
Hinge F
The distances of the masses are then adjusted until the rule
Solution balances horizontally once again. The distances d1 and d2 are
Taking moments about the Hinge; measured and recorded.
𝑀𝑜𝑚𝑒𝑛𝑡 𝑜𝑓 𝐹𝑜𝑟𝑐𝑒 = 𝐹𝑜𝑟𝑐𝑒, 𝐹 × 𝑃𝑒𝑟𝑝. 𝑑𝑖𝑠𝑡𝑎𝑛𝑐𝑒
𝐶𝑙𝑜𝑐𝑘𝑤𝑖𝑠𝑒 𝑚𝑜𝑚𝑒𝑛𝑡 = 12 × 0.8 The experiment is repeated several times and the results
𝐶𝑙𝑜𝑐𝑘𝑤𝑖𝑠𝑒 𝑚𝑜𝑚𝑒𝑛𝑡 = 9.6𝑁𝑚 tabulated including values of w1d1 and w2d2.

Example;2 It is found that; w2d2 = w1d1. Where w2d2 is the clockwise

The moment of a force is 4Nm in the clockwise direction moment and w1d1 is the anticlockwise moment. This verifies
when the lid of a tin is opened. Calculate the vertical force the principle of moments.
applied, if the perpendicular distance from the hinges is
40cm. The points from which moments are being taken acts as the
pivot and the moments of force at that point is zero (0).
Solution Clockwise clockwise Perpendicular
( ) = ( ) ×( )
moments force distance from pivot
F
40c Anti − Anti −
m Perpendicular
(clockwise ) = (clockwise) × ( )
Hinge distance from pivot
moments force

Taking moments about the pivot;

Taking moments about the Hinge;

Moment of Force = Force, F × Perp. distance
4 = F × 0.4
4
F = N
0.4
F = 10N
Thus the vertical force applied is 10N

©[email protected] 28
 respectively from the zero mark. If the metre rule balances
horizontally, find the value of F.
d2
Solution
d1 Fulcrum m2 0 cm 50 cm 100 cm
G
W2

6N 2N F
m1 20cm
60cm
W1= 80cm
Taking moments about the pivot;
Sum of Anticlockwise moments =6×30 = 180Ncm
Clockwise moments =W1 xd1= W1d1 Sum of Clockwise moments =2×10+F×30
Anticlockwise moments =W2 x d2= W2d2 =(20+30F) Ncm
And by the law of moment; Applying the principle of moments;
Sum of clockwise moments = sum of anti-clock moment Sum of clockwise moments = Sum of anticlockwise moments
about any point. Thus, W1d1= W2d2 (20+30F) Ncm =180Ncm
30F =160
Note: When calculating moments about a point (pivot) all F =5.3 N
distances should be measured from that point.
Example 4:
Finding the mass and weight of uniform body A non-uniform tree trunk of weight 1000N is placed on a
 When body is uniform, the mass or weight must act at pivot, 4m from the thick end. A weight of 800N is placed on
the centre. the other side of the pivot, at a distance equal to that from
 A metre rule is marked from 0-100cm mark. If it is the thick end to the centre of gravity, just tips off the tree
uniform, then its mass/weight must act in the middle, trunk. How far is the weight from the thick end?
which is 50cm mark.
 The mass or weight is calculated by applying the
Solution:
principle of moment.

Example 2:
A metre-rule suspended from the centre of gravity is in
equilibrium, i.e balanced at G, when forces ofW 1, W2 and
W3, act at distances of a, b and c respectively from the pivot. Trunk
C.O.G
(i) Draw a labeled diagram to show all the forces acting on 800N
the metre-rule.
Pivot
.
x x
d1 d3
1000N
d2 50 cm
0 cm
4m
G

W3 Let the distance from the thick end to the Centre of gravity
W1 W2
(C.O.G) be x.

(ii) Write an expression for the sum of the moments. Taking moments about the pivot;
Taking moments about the pivot;
Sum of Anticlockwise moments = W1 × d1+W2 × d2 Applying the principle of moments;
Sum of Clockwise moments = W3 ×c Sum of clockwise moments = Sum of anticlockwise moments
(800 × 𝑥 ) Nm =1000× (4 - 𝑥) Nm
Applying the principle of moments; 800𝑥 = 4000 -1000𝑥
Sum of clockwise moments = Sum of anticlockwise moments 1800𝑥 = 4000
W3 × c = W1 × a + W2 × b 1800𝑥 4000
=
1800 1800
Example3: 𝑥 = 2.2m
A uniform metre rule is pivoted at its centre and three forces Thus the heavy weight, is (4+2.2) m = 6.2m from the thick
of 6N, 2N and F act at distances of 20cm, 60cm, and 80cm end.

©[email protected] 29
Example: 1  Then the required value is calculated from the principle
A uniform metre rule is suspended from 40cm marking as of moment.
shown in the diagram below. Find the mass of the metre rule
if it’s in equilibrium. Example:5 A uniform metre rule is pivoted at 30cm mark.
It balances horizontally when a body of mass 20g is
suspended at 25cm mark.
0 cm 40 cm mark 100 cm
G a) Draw a force diagram for the arrangement.
b) Calculate the mass of the metre rule
(Ans: m=5g)
2kg m
d
x Example: 6 A uniform half-metre rule is pivoted at 15cm
10cm
mark and balances horizontally when a body of 40g is
Taking moments about the pivot; hanging from 2cm mark.
𝒙 = (40 − 10) = 30𝑐𝑚 i) Draw a diagram of the arrangement.
𝒅 = (50 − 40) = 10𝑐𝑚 ii) Calculate the mass of the metre rule.
(Ans: m=52g)
Applying the principle of moments;
Sum of clockwise moments = Sum of anticlockwise moments Example: 7 A uniform rod AB of length 5cm is suspended
(2 × 𝑥 ) = m× d at 2m from end A. if the mass of the rod is 10kg. Calculate
2(30) = 10m the mass of the body, which must be suspended at 1m from
60 = 10m end A so as for the rod to balance horizontally.
10m 60 (Ans: m=5kg)
=
10 10
m = 6kg Example: 8 A hand cart of length 1.5 m, has the centre of
Thus, the mass of the metre rule is 60kg gravity at length 0.5 m from the wheel when loaded with
50kg as shown below.
Example 2: A uniform metre rule pivoted at 10cm mark
balance when a mass of 400g is suspended at 0cm mark.
Calculate the mass of the metre rule. (Ans: m=100g)

Example 3: The diagram below is a metre rule pivoted at

80cm mark. Calculate the mass of the metre. (Ans: m=67g)

0 50 cm 80cm 90cm
cm cm
G If the mass of the hand cart is 10 kg, find the effort needed
to lift the hand cart.
m 200kg
y Condition for Body to be in Equilibrium Under action of
x
parallel forces.
Example 4: A uniform beam 2m long is suspended as
shown below. Calculate the mass of the metre. (Ans: When a number of parallel forces act on a body such that the
m=16kg) body attains equilibrium, then the following conditions must
be met or fulfilled:
(i) The sum of the forces is one direction is equal to
0.5m 1.5 m the sum of forces in the opposite direction.
(ii) The sum of the clockwise moment about any point
G
is equal to sum of the anti-clockwise moments
about the same point.
20k m
g x y The above conditions are useful in calculations involving
10c two unknown forces. The following steps should be taken.
m (i) An equation for sum of force in one direction equaling
Interpreting the question in diagram form.
 the diagram for any body should be drawn in the form. to sum of forces in the opposite direction is written.
 if the body is uniform, its mass or weight will act from (ii) Moments should be taken about one of the unknown
the centre of gravity which is obtained by, force. Where by the sum of anticlockwise moment is
L equal to sum of the clockwise moments.
C. o. g =
2
i.e. For a uniform metre rule, which is marked from 0- Example:
100cm, the centre of gravity from which the mass or weight A uniform wooden beam of length 2m and weight 34N rests
acts is, on two supports A and B placed at 40cm from either end of
L 100cm the beam. Two weights of 40N and 50N are suspended at
C. o. g = = = 50.0cm the end of the beam.
2 2
©[email protected] 30
(i) Draw a diagram to show the forces acting on the beam.
(ii) Calculate the reactions at the supports.
T1 T2
Solution:
(a) C.O.G
R1 R2

40cm
C.O.G 50cm 50cm 100cm
40cm

A 500N 50N B

40N 34N 50N

(b) Find the tension on A and B
A B
Example 1: A truck of weight 20KN is driving across a Solution
uniform 50m long bridge of weight 500KN as shown below. Sum of upward forces=sum of downward forces
T1 + T2 = 500N + 50N
R1 R2 T1 + R 2 = 550N………………………(i)
C.O.G
Since T1 and T2 are, unknown forces so moments can be
taken about either T1 or T2 .
5m 25m
Taking moments aboutR1 :
A 20KN 500KN B Sum of clockwise moments = Sum of anticlockwise moments
Calculate the reactions at “A” and “B” if the bridge is in (500 × 50)+(50×100) = T2 × 200
equilibrium sum of forces in one direction = sum of forces 25000+5000 = 200T2
in opposite direction. 30000 = 200T2
200T2 30000
=
Solution 200 200
Sum of upward forces=sum of downward forces T2 = 150N
R1 + R 2 = 20KN + 500KN Substituting for T2 = 150N into equation (i), gives;
R1 + R 2 = 520KN………………………(i) T1 + 150 = 550
T1 = 400N
Since R1 and R 2 are, unknown forces so moments can be Thus, the Tensions T1 and T2 respectively are 400N and
taken about either R1 or R 2 . 150N.

Taking moments aboutR1 : (c) Find the fraction of the total weight that is supported by
B.
Sum of clockwise moments = Sum of anticlockwise moments
(20 × 5)+(500×25) = R 2 × 50
Weight supportd by B
100+12500 = 50R 2 Fraction =
12600 = 50R2 Total weight
50R 2 12600
= 150
50 50 Fraction =
R 2 = 252KN 550
Substituting for 𝑅2 = 252KN into equation (i), gives;
R1 + 252 = 520 3
Fraction =
R1 = 268KN 11
Thus, the Reactions R1 and R2 respectively are 268KN and
252KN. Centre of gravity
Centre of gravity is the point of application of the resultant
Example 2: Two labourers “A” and “B” carry between force due to the earth’s attraction on it. All bodies are made
them a load of 500N on a uniform pole of weight 50N. if the of a large number of tiny equal particles each of mass “m”
pole is 2m long, and the load is 50cm from A towards B. and pulled towards the earth with a force “mg”. If the total
mass of the entire particle in a body is “m” then the resultant
(a) Draw a diagram to show the force acting on the poles. force of gravity on the body is mg and it acts vertically
downwards at the point G.

The centre of gravity or centre of the mass is a fixed point in

the object where the resultant weight, (force of gravity)
seems to act. If the centre of gravity is taken to, any other
point of support is not zero.

©[email protected] 31
Centre of gravity or regularly shaped object.
The mass or weight is evenly distributed and its centre or (a) Stable equilibrium:
gravity is in the middle, which is at the geometric centre of Is the type of equilibrium where, if the body is slightly tilted
the shape. and then released:
(i) the centre of gravity of the body is raised.
(ii) the body returns to its original position.
G G G

Square Rectangle Rhombus F h

mg
mg

(b) Unstable equilibrium:

e.g. uniform metre rule. Is the type of equilibrium where, if the body is slightly tilted
and then released:
50 cm mark (i) the centre of gravity of the body is lowered.
0cm (c.o.g) 100 cm (ii) the body moves farther away from its original position.
F
h
mg
Finding the centre of gravity of an irregularly shaped
object (lamina).
mg
A
(c) Neutral equilibrium:
Lamina Is the type of equilibrium where, if the body is slightly tilted
C.O.G and then released:
(i) the centre of gravity of the body is neither raised nor
B lowered.
C
(ii) the body stays in its new position or it just rolls on
before stopping.
Retort Example:
stand Plumb line A ball on a flat surface.

Plumb
h

Marking holes: Three holes “A”, “B” and “C” are made in mg mg
the object at the edges far away from each other.

Marking the cross lines: The object is suspended on a retort How to increase the stability of a body.
stand from each of the holes and plumb (or pendulum bob) The stability of a body can be increases by:
is used to trace the centre of gravity by marking a line on the (i) Lowering the centre of gravity by putting more weight
object tracing the plumb line thread when swinging stops. at the base.
(ii) Increasing the area of the base.
Repeating: The experiment is repeated with the object hung (iii) If the body is slightly displaced and then released.
at B and C and cross lines marked. The point C.O.G at
which all the lines cross is the centre of gravity of the body. Exercise: See UNEB
2003 Qn. 5 1993 Qn.14
1:5:2 STABILITY: 1987 Qn.10 2000 Qn.11 and Qn.2
Stability is the difficulty with which a body topples. 1988 Qn.2 and Qn.7 2002 Qn.11
When a body is at rest, it is said to be in a state of 1989 Qn.15 and Qn.38 2003 Qn.5
equilibrium or stability. 1991 Qn.30 2007 Qn.17 and Qn.5

Types or states of stability or Equilibrium

Some bodies are in a more stable state than others.
There are three types or states of equilibrium or stability:
a) stable equilibrium
b) unstable equilibrium
c) neutral equilibrium

©[email protected] 32
 SIMPLE MACHINES:
1: 6. MACHINES A simple machine is a device that work with one movement
and change the size and direction of force.
A machine is a device on which a force applied at one point,
is used to overcome a force at another point. Examples of simple machines:
A machine is a device, which simplifies works by 1.Lever system 5.Screws
magnifying the effort. 2.Wheel and Axle machine 6.Inclined Planes
. 3. Gear system 7. Wedges
Principle of machines: 4. Pulley systems
It states that a small force (effort) moves over a large
distance to produce a bigger force that moves the load over a
small distance. (𝐚) 𝐋𝐄𝐕𝐄𝐑 𝐒𝐘𝐒𝐓𝐄𝐌:
Effort: Is the force applied at one point of a machine to A lever is a rigid bar, which is free to move about a fixed
overcome the load. point called fulcrum or pivot.
Load: Is the force, which is overcome by the machine using It works on the principle of moments.
the effort.
Classes of levers:
Mechanical Advantage (M.A): Class of lever Position of F,E,L Examples
This is the ratio of load to effort. 1st F is between E and L Pair of scissors
Load 2nd L is between E and F Wheel barrow
i.e; M.A=
Effort 3rd E is between F and L Human arm
Note:-Mechanical advantage has no units.
-M.A is the number of times the load is greater than Class of lever Examples
the effort. Alternatively, it (i) First class lever:  See-saw
gives the number of times the machine magnifies the effort. Is a lever system where the  Pair of scissors
Velocity ratio (V.R):
fulcrum (or pivot) is between  Pair of pliers
This is the ratio of the distance moved by the effort to the
the load and the effort.  Weighing scale
distance moved by the load.  Claw Hummer
Distance moved by effort
i.e; V.R= (ii) Second class lever:  Wheel barrow
Distance moved by load
Note: It is the ratio of the velocity of the effort to the Is a lever system where the load  Nutcracker
velocity of the load in the same time. is between the fulcrum (or  Bottle opener
It is independent of friction. pivot) and the effort.

Efficiency (𝜼): (iii) Third class lever:  Fishing rod

This is the ratio of work output to the work input expressed Is a lever system where the  Pair of tongs
as a percentage. Effort is between the fulcrum  Human arm
Work output (or pivot) and the load.  Spade
i.e; Efficiency (η) = × 100%  Forceps
Work input
Work out put = Load × load distance
Work input = Effort × Effort distance NOTE: -Load arm is the distance of the load from pivot.
-Effort arm is the distance of effort from pivot.
𝐋𝐨𝐚𝐝 𝐄𝐟𝐟𝐨𝐫𝐭 𝐚𝐫𝐦
Load × load distance -𝐌. 𝐀 ≈ 𝐕. 𝐑 ⟹ ≈
Efficiency = × 100% 𝐄𝐟𝐟𝐨𝐫𝐭 𝐋𝐨𝐚𝐝 𝐚𝐫𝐦
Effort × Effort distance Hence, a lever system is more efficient compared to other
Load Load distance machines.
= × × 100%
Effort Effort distance
1
= M.A × × 100% Fulcrum (or Pivot)
V. R
𝐌. 𝐀
Efficiency (η) = × 𝟏𝟎𝟎% Load arm Effort arm
𝐕. 𝐑
Load Effort
NOTE:
The efficiency of a machine system is always less than (𝐛) 𝐖𝐇𝐄𝐄𝐋 𝐀𝐍𝐃 𝐀𝐗𝐋𝐄 𝐌𝐀𝐂𝐇𝐈𝐍𝐄 ∶
100% because of;
 Friction in the moving parts of the machine.
This consists of two wheels of different radii on the same
 Work wasted in lifting useless weights like
axis. The axle has the same attachment on the wheel.
movable parts of the machine.
The effort is applied to the wheel and a string attached to the
axle raises the load.
The efficiency can be improved by;
 Oiling or greasing the movable parts.
 Using lightweight materials for movable parts.

©[email protected] 33
 Example2:
A wheel and axle machine is constructed from a wheel of
diameter 20cm and mounted on an axle of diameter 4cm.
(a) Calculate the;
(i) Velocity ratio of the machine
(ii) Greatest possible value of mechanical
advantage.
(b) Explain why the mechanical advantage is likely to be
less than this value.

Solution:
For a complete turn or rotation; D =20cm⟹ R = 10cm, d = 4cm ⟹ r = 2cm
 The effort moves through a distance equal to the (a)(i)
circumference of the wheel.𝐂 = 𝟐𝛑𝐑, R= radius of Distance moved by effort 2πR
V.R= =
wheel. Distance moved by load 2πr
 The load moves through a distance equal to the
circumference of the axle. 𝐂 = 𝟐𝛑𝐫, r= radius of axle. R
=
r
Distance moved by effort
 Thus, from; V.R =
Distance moved by load 10
=
2πR 2
= V. R = 5.
2πr Thus, the velocity ratio is 5.
R
V.R = (a)(ii)
r For the greatest (or maximum) mechanical advantage, the
Example1: system is 100% efficient.
The figure below shows a wheel land axle system, which
Hence M.A=V.R= 5
uses an effort of 300N to raise a load of 900N using an axle
of radius 10cm.
(b) The M.A is likely to be less than 5 because work needs
to be done against friction
R=40cm
Example3:
r=10cm A common windlass is used to raise a load of 480N by
application of an effort 200N at right angles to the handle. If
the crank is33cm from the axis and the radius of the axle is
11cm, calculate the;
(i) Velocity ratio. (Ans: V.R=3)
900N (ii) Efficiency of the windlass. (Ans: η =80%)
300N
Calculate the; (i) velocity ratio (𝐜) 𝐆𝐄𝐀𝐑 𝐒𝐘𝐒𝐓𝐄𝐌:
(ii) Efficiency of the system A gear is device consisting of toothed wheels.
Solution: These are rigidly fixed to the axis and turn with their axis.
R= 40cm, r =10cm; L= 900N, E=300N; Driven gear
Driving gear
Distance moved by effort 2πR
Thus, from; V.R = =
Distance moved by load 2πr N
(i) (ii). n
R 40 M.A =
Load
=
900
=3
V.R = = =4 Effort 300
r 10 M.A = 3
Thus, the velocity ratio is 4.
Effort

Load
They change direction and speed of rotation when the effort
applied is not changed.
M. A The direction of the driven gear is opposite to that of the
Efficiency (η) = × 100% driving gear.
V. R
3 The number of rotations of the gear wheels depends on the
η = × 100% ratio of number of teeth and the radii of the wheels.
4
η = 75% .
Thus, efficiency is 75% .

©[email protected] 34
The effort and the load are applied on the shafts connected Example: 3
to the gear wheels. A large V.R is obtained only when the Two gear wheels P and Q with 25 and 50teeth respectively
effort is applied on a small gear so that it drives the large lock into each other. They are fastened on axles of equal
gear. diameters such that a weight of 400N attached to the string
wound around one axle raises a load of 600N attached to a
Number of teeth on driven gear 𝐍 string wound around the other axle. Calculate the:
V. R = = (i) Velocity ratio and efficiency when Q drives P.
Number of teeth on driving gear 𝐧
[Ans: V.R = 0.5, Efficiency = 300%]
Example 1:
Two gearwheels A and B with 20 and 40 teeth respectively (ii) Velocity ratio and efficiency when P drives Q.
lock into each other. They are fastened on axles of equal [Ans: V.R = 2, Efficiency = 75%]
diameters such that a weight of 400N attached to a string
wound around one-axle, raises a load of 600N attached to a
string wound around the other axle. Calculate the: (𝐝) 𝐒𝐂𝐑𝐄𝐖 𝐌𝐀𝐂𝐇𝐈𝐍𝐄 ∶
(a) Velocity ratio of the system when; (i) A drives B
(ii) B drives A A screw is a nail or bolt with threadlike windings.
(b) Efficiency when; (i) A drives B It is like a spiral stair case.
(ii) B drives A It is an essential feature of machines like the vice and the
Solution: screw jack.
(a) N=40cm, n=20cm
L=600N, E=400N
Number of teeth on driven gear N
(i)Thus, from;V. R = =
Number of teeth on driving gear n

NB Load 600
V.R = (iii) M.A = = = 1.5
Effort 400
nA V. R = 2.
40 M. A
=  The distance between any two successive threads of a
20 Efficiency (η) = × 100%
V. R screw is called a Pitch.
V. R = 2.  An effort is applied on a handle like in a vice or in a car
The velocity ratio is 2. 1.5 jack.
η= × 100%
2  For a complete turn (or rotation) of the effort, the load
(ii) moves through a distance equal to 1pitch while the
NA
V.R = η = 75% . effort moves a distance equal to the circumference of
nB the handle
(ii) M.A=1.5 .
20 V.R =2 Distance moved by effort circumference of handle
= V.R= =
40 Distance moved by load 1Pitch
V. R = 0.5. M. A 𝟐𝛑𝒍
The velocity ratio is 0.5. Efficiency (η) = × 100% V.R =
V. R 1Pitch
1.5 Example 1:
η= × 100%
0.5 In a screw jack, the length of the handle is 56cm and a pitch
of 2.5mm. It is used to raise a load of 2000N. Calculate the;
η = 300% (i) Effort required to raise the load. (Ans: E = 1.42N).
(ii) V.R (Ans: V.R = 1408).
Example 2: (iii) Efficiency of the screw, hence explain the significance
P of your value of efficiency. (Ans: η =100%)

Example 2:
450N
A load of 800N is raised using a screw jack whose lever arm
N
Q is 49cm has a pitch of 2.5cm.If it is 40% efficient, Find the
(i) V.R
(ii) M.A

I50N Example 3:
A certain screw machine has a pitch of 3.5mm. The effort is
Two gear wheels P and Q with 80 and 20 teeth respectively,
applied using a handle, which is 44cm long. Calculate its
lock each other. They are fastened on axles of equal
velocity ratio. (Ans: V.R = 3.95)
diameters such that a weight of 150 N attached to a string
wound around one-axle raises a load of 450N attached to a
string wound around the other axle. Calculate the; Example 4:
A screw jack with a lever arm of 56 cm, has threads which
(i) Velocity ratio of the gear system. (Ans: V.R=4)
are 2.5mm apart is used to raise a load of 800N. If its 25%
(ii) Efficiency of the system. (Ans: η =75%)
efficient, find the;

©[email protected] 35
(i) Velocity ratio (Ans: V.R = 1408) V. R = 3.
(ii) Mechanical advantage (Ans: M.A = 352) Thus, the velocity ratio is 3 .

Solution: (iii) M.A(=5N) (iv) Efficiency

2.5 M. A
(a) Radius (lever arm),l =56cm, Pitch of a screw = = L=400N, E=150N
10
Load 400 (η) = × 100%
0.25cm V. R
M.A = =
L= 800N. Effort 150
2.67
2π𝑙 η= × 100%
V.R of a screw = = 2.67 3
1Pitch η = 88.9%
2 × 3.14 × 56 (v) Work input
V.R of a screw = Work input = Effort × Effort distance
0.25
= 1406.72 Work input = 150 × 15
= 2250J
(vi) Work out put
(𝐞) 𝐈𝐍𝐂𝐋𝐈𝐍𝐄𝐃 𝐏𝐋𝐀𝐍𝐄 Work out put = Load × load distance
An inclined plane is a slope, which allows a load to be Work out put = 400 × 5
raised more gradually by using a smaller effort than when = 2000J
lifting vertically upwards.
Practice Question:
1. A wooden plank, 3m long is used to raise a load of
1200N through a vertical height of 60cm. If the friction
l between the load and the plane is40N, calculate the:
(i) effort required [Ans: E = 280N]
(ii) Mechanical advantage [Ans: M.A = 4.29]
F
h
2. In the gear system in figure 3 below N1 and N2 are the
number of teeth on the wheels. The efficiency of the
𝜃 gear system is 60%.
𝑁2 = 100
𝑁1 = 20
Distance moved by effort length of the plane gear
V.R= =
Distance moved by load height of the plane
N
𝐥
= n
𝐡
𝟏
OR: V.R =
𝐬𝐢𝐧 𝛉

Example: Effort
A load of 400N is pulled along an inclined plane as shown
Load
below.
Find the;
(i) Velocity Ratio.
15cm (ii) Load that can be raised by an effort of 200N.
(iii) Explain why its preferred to use a longer ladder to
a shorter ladder when climbing a tree.
150N
5cm
400N
𝜃
Calculate the;
Solution:
(i) V.R (=3)
l=15cm, h=5cm
(i)Thus, from;
length of the plane 𝒍
V.R = =
height of the plane 𝒉
𝒍
V. R =
𝒉
𝟏𝟓
V. R =
𝟓

©[email protected] 36
 (𝐟) 𝐏𝐔𝐋𝐋𝐄𝐘 𝐒𝐘𝐒𝐓𝐄𝐌: Load 2E
M.A = = = 2. (since L = 2E)
Effort E
A pulley is a wheel with a grooved rim over which a string
passes. M.A and V.R of a single movable pulley is two
However, in practice, the M.A. of a single movable pulley is
Types of pulleys. less than two. Because of the following reasons;
(i) Single fixed pulley (i) Some energy is wasted in overcoming friction.
(ii) Single movable pulley (ii) Some energy is wasted in lifting useless loads like
(iii) Block and tackle pulley system threads.

A single movable pulley is more advantageous than a single

(i) Single fixed pulley fixed pulley. In that, for a single movable pulley the effort
This is the type of pulley fixed on a rigid support. required to raise a load is less that the load.

(ii) Block and tackle pulley system

This is consists of two blocks each having one or more
pulleys, combined together to form a machine. This is done
in order to have high velocity ratio and a higher mechanical
Effort, E advantage.
It is applied in:
 Cranes
 Brake downs For raising heavy loads
 lifts
Load, L
Note: (i) The number of portions of the string supporting the
It is applied in:
lower block is equal to the velocity ratio of the system.
 Raising a flag
(ii) The effort applied is equal to the tension in each
 Lifting building materials during construction
string supporting the movable block.
Here, -load distance = effort distance
E.g. If the effort is 6N, the tension in each string is also 6N.
-tension is the same throughout the string.
(iii) For an odd number of pulleys in a system, the
-If no friction is considered, Load = Effort. Hence
Load E upper block contains one more pulley than the lower block.
M.A = = = 1. (since L = E) In addition, the string starts from the lower block.
Effort E

However, in practice the mechanical advantage and V.R of a

single fixed pulley is less than one. Because of the
V.R= 4 V.R= 5
following;
(i) Some energy is wasted in overcoming friction.
(ii) Some energy is wasted in lifting useless loads like
threads.
Effort, E
(ii) Single movable pulley
Effort, E
Effort, E

Load, L Load, L
Load,

Here, the effort distance is twice the load distance.

Here, -load distance = 2 x effort distance
-tension is the same throughout the string.
-If no friction is considered, Load = Effort. Hence
Load 2E
M.A = = = 2. (since L = 2E)
Effort E
At balancing;
Sum of upward force = sum of downward forces
L =E+E
𝐋 = 𝟐𝐄

©[email protected] 37
 Drawing the graph:
From the table a graph of efficiency or mechanical
advantage against the load is plotted.

V.R= 3 V.R= 6
Efficiency Mechanical advantage

10 V.R
Effort, E Effort, E 0
10
0

0 Load (N) 0 Load (N)

Explanation of the shape of the graphs:

Load, L Load, L  As the load increases, the efficiency also increases
Passing the string  This is because the weight of the movable pulley block
 If the number of pulley wheels is odd, then the string and friction become very small compared to the load.
should be tied down to the movable block.
 For even number of pulley wheels, the string should be Note:
tied up to the fixed block. In practice, the movable block has some weight (w) and
there is friction (F). These two together with the load (L) act
Experiment to measure mechanical advantage and downwards and they become part of the total downward
efficiency of pulley system. forces.
Thus, the efficiency do not increase beyond 100% because;
i) some energy is wasted on overcoming friction
ii) Some energy is wasted on lifting useless loads
like movable pulley blocks.

Therefore at Equilibrium;
Sum of upward forces = sum of downward force
𝐒𝐮𝐦 𝐨𝐟 𝐭𝐞𝐧𝐬𝐢𝐨𝐧𝐬
[ 𝐬𝐮𝐩𝐨𝐫𝐭𝐢𝐧𝐠 𝐥𝐨𝐰𝐞𝐫 ] = Load(L)+Weight(W)+Friction(F)
𝐛𝐥𝐨𝐜𝐤, (𝐕. 𝐑) 𝐄
V.R = L+W+F
Effort
(Weights added+ Example 1:
weight of scale pan) Below is a pulley system of mass 0.4kg, and there is friction
of 5N

Load pan

Determining effort: A known load is place on the load pan Effort

and knows weights are added to effort pan until the load just E E E E
rises steadily when given a gentle push.
Repeating: The experiment is repeated with different loads
and the results are recorded in table shown bellow:
V.R=……….

Load (N) Effort Load M.A

M.A= Efficiency=
(N) Effort V.R
× 100

200N
………. …… ………… …………….
(a) Calculate the;

©[email protected] 38
(i) Velocity ratio of the system Work out put = Load × distance
Number of portions of the string = 300×5
V.R = ( )
suporting the movable block = 1500N
𝑉. R = 4
Example 2:
(ii) Effort required to raise the load. A pulley system of velocity ratio 3 is used to lift a load of
Solution 100N. The effort needed is found to be 60N.
Data (a) Draw the arrangement of the pulley system.
L=200N, m =0.4Kg, F=5N, E=?,
W=mg = 0.4 x 10 Solution
W=4N Velocity ratio is odd. then;
Velocity ratio 3
Number of pulley wheels on each block = = =
Sum of upward forces = sum of downward force 2 2
1 remainder 1.
E+E+E+E = L+W+F
The remainder wheel is added to fixed block.
4E = L + W + F
4E = 200 + 4 + 5
4E = 209
4E 209 V.R= 3
=
4 4
E = 52.25N

(iii) Mechanical advantage of the system

Load E=60N
M. A =
Effort
200
=
52.25
M. A = 3.83

(b) If the load is raised through 6m, calculate the distance

the effort moves at the same time.
Example 2:
L=100N
Data
L.D =6m, E.D =?
Effort distance (b) Calculate the efficiency of the system.
V. R = Solution
Load distance
V.R =3
E. D Load M.A
4 = M. A= Efficiency= × 100%
6 Effort V. R
E. D = 4 × 6 100 1.67
= Efficiency= × 100%
E. D = 24m 60 3
M. A= 1.67 Efficiency = 55.56%
Example 2:
A pulley system has two pulleys on the bottom block. A
load of 1000N is hung from the bottom block, it is found Coupled machines
that an effort of 300N to raise the load. If two or more machines are, coupled machines such that the
(i) How much energy is supplied, if the effort moves output of one is connected to the input of the other, the over
through 5m? all performance is summed up by:
Solution Overall -V.R = V.R1 + V.R2
Data -M.A. = M.A1 + M.A2
L=1000N, E=300N, E.D =5m -Eff = Eff1 + Eff2
Work in put = Effort × Effort distance
= 300 × 5
= 1500N

(ii) If the effort moves through 5m, find how far the laod
rises.
Solution
Data
E.D =5m, V.R=4, L.D=?
Effort distance
V. R =
Load distance
5 5
4= ⟹ 4L. D = 5 ⟹ L. D = ⇒ 𝐋. 𝐃 = 𝟏. 𝟐𝟓𝐦
L. D 4
(iii)Find how much energy is gained by the load if the effort
moves through 5m.

©[email protected] 39
 If the car bears down on the car with a force of 5000N and
that efficiency of a screw jack is 15%. Calculate the;
a) V.R.
2
Given; Radius, r = 2cm = = 0.02m
100
2
Pitch, P = 2mm = = 0.002m
1000

(b)The effort required to turn the

Then; handle
Effort Distance
V.R= Load
Load Distance M.A=
2𝜋𝑟 Effort
V.R=
𝑃𝑖𝑡𝑐ℎ
5000
2(3.14)(0.02) 9.42 =
V.R= E
0.002 9.42E =5000
V.R=62.8 9.42E 5000
=
9.42 9.42
Mechanical Advantage E=530.79N

Given;Efficiency=15%
, V.R= 62.8 (c)Work done by the operator in
Then; order to raise the side or the car by
The diagram above shows a pulley system used by a sailor M.A 25cm.
for hoisting. Calculate the: Effi = × 100%
V. R
M.A Work output
(a) Velocity ratio of the system 15%= × 100% Eff = × 100%
62.8 Work input
Solution
Velocity ratio of lower block = 4 M.A
0.15 = Work output=Load × Load distance
Velocity ratio of middle =2 62.8 25
Velocity ratio of upper block = 1 Work output=5000× ( )
Overall V.R = 4 + 2+ 1 = 7 M. A = 0.15(62.8) 100
Work output=1250J
M. A = 9.42
(b) The effort required to lift the load if the efficiency of the
system is 75%. NB: Work input is the work done by the effort. Sometimes it
Solution is considered as the work done by operator.
Then from;
M.A Load Work output
Efficiency= × 100% M. A= Efficiency = × 100%
V. R Effort Work input
M.A 1500
75%= × 100% 5.25=
7 E 1250
M.A 15% = × 100%
0.75= Win
7 5.25E= 1500
M.A =0.75×7 E = 285.7N 1250
M. A = 5.25 0.15 =
Win
Example:
The diagram below shows a screw jack being used to lift a 0.15Win = 1250
car in order that a wheel may be charged.
𝑊𝑖𝑛 = 8333.33J
20cm In general;
Work wasted = work input - work output
= 8333.33 – 1250
= 7083.33J

From above, it is noted that work input is greater than

2mm workout put due to;
i) some work wasted in lifting useless loads,
Collar ii) Some work wasted in reducing friction.

Note: For the screw the velocity ratio is very high because
the length of the handle is very big compared to the pitch of
the screw.

©[email protected] 40
However the efficiency is very low. Usually lower than
50%. This is because friction is very high so the screw 1: 7. WORK, ENERGY AND POWER
cannot run back if left.
1:7:1. WORK
Exercise : See UNEB Work is the product of the force applied and the distance
1999 Qn.2 1998 Qn.6 moved by the point of application of the force in the
1994 Qn.8 2006 Qn.4 direction of the force.
1987 Qn.36 1992 Qn.6 Note that the distance moved has to be in the direction of the
1988 Qn.34 2001 Qn.42 applied force. It is common that a force may be applied to
1991 Qn.26 2007 Qn.1 move an object to the right, but instead the object moves to
the left.
The force in this case has not done any work.

Work done = Force, F × Displacement, S

W = FS

The S.I unit of work done is a joule (J)

Definition:
A joule is the work done when the point of application of a
force of 1N, moves through a distance of 1m in the direction
of the force.

Example: 1
1. Calculate the work done when a force of 9000N acts on a
body and makes it move through a distance of 6m.

Solution
Force, F= 9000N
Distance, s = 6m

Work done = Force, F × Displacement, S

W= F×S
W= 9000×6
W= 54000J

Note:
If an object is raised vertically or falling freely, then the
force causing work to be done is weight.
Force = Weight = mass, m × acceleration due to gravity, g
Force = Weight= mg

Thus, the work done against gravity is given by;

Work done = Weight × height
Work done = mgh
Where m is mass in kg, h is distance in metres and some
times, it is height.

Example:2
A block of mass 3kg held at a height of 5m above the
ground is allowed to fall freely to the ground. Calculate the
workdone.
Solution
Given, mass, m = 3Kg, Distance, s = 5m
Force F= Weight, W =mass × g
F= mg
= 3×10
F = 30N
Work done = Force, F × Displacement, S
W= F×S
W= 30×5
W= 150J

©[email protected] 41
Example: 3
A man of mass 80kg runs up a staircase of 10stairs, each of (a) Non-renewable sources of energy
vertical height 25cm. Find the work done against gravity. These are energy sources, which cannot be replaced when
Solution: they get used up.
Given, mass m = 80Kg, Examples of non- renewable sources of energy
25 (i) Fossil fuels; these are formed from plant remains that
Distance, h = 25cm = = 0.25m
100 died million years ago. They include; coal, petroleum oil,
Total Distance, ℎ 𝑇 = 0.25m×10stairs natural gas, e.t.c.
Total Distance, ℎ 𝑇 = 2.5m (ii) Nuclear fuels; these are fuels found in radioactive
Then; elements which may be occurring naturally such as
Uranium.
Work done = Weight × height These fuels can be used in nuclear reactions to produce
Work done = mgh electricity.
= 80×10×2.5
Work done = 2000J Advantages of non-renewable source of energy.
 They have high energy density. I.e a lot of energy
can be produced from a small quantity.
Example: 4  They are readily available as demand increases.
A crane is used to to raise 20 tonnes of concrete to the top Disadvantages of non-renewable source of energy.
floor of a building 30m high. Calculate the total work done  They are highly polluting.
by the crane.
Solution: (b) Renewable sources of energy
Given, mass m = 20tonnes=20×1000=20,000Kg, These are energy sources which can be replaced when they
Distance, h = 30m get used up. They can never get exhausted.
Then; Advantage:
They are non-polluting.
Work done = Weight × height
Work done = mgh Examples of renewable sources of energy.
= 20,000×10×30 (i) Solar energy: This is the form of energy which reaches
Work done = 6,000,000J the earth in form of heat and light.
It can be harvested using solar panels and transformed
Example: 5 into electrical energy, which is used for many purposes.
The figure bellow shows a bale of hay being pulled up an It is also used in direct low temperature heating.
inclined plane with a force of 200N. The bale moves down (ii) Wind: Wind can be harvested using giant windmills,
the incline to a distance of 5m. which can turn electrical generators to produce
electrical energy, which is a more useful form.
200N (iii) Running water: Running water is used in hydro-
electricity plants to turn giant turbines, which produce
electrical energy.
5m The water will always flow hence a renewable source.
Tides can also be used to generate electricity in this
way.
(iv) Geothermal energy: Water is pumped to hot under
ground rocks where it’s heated and then forced out
(i) Calculate the work done by the force. through another shaft where it can turbines.
Solution:
Work done = Force, F × Displacement, S
= 200N×(-5m) Forms of energy
Work done = -1000J Energy can exist in the following forms;
a) Chemical energy:
(ii) Explain your answer. Chemical energy is the form of energy a body has due to the
The distance moved by the bale, was in a direction opposite nature of its atoms and molecules and the way they are
to that of the force applied hence a negative displacement. arranged.
The negative in the answer therefore means that the bale did In the combination of atoms to form compounds, there is
the work instead of the force applied. gain or loss of energy. This energy is stored in the
compound as chemical energy.
If the atoms in such compounds are rearranged to form a
1:7:2. ENERGY new compound, this energy is released. E.g If sugars in the
Energy is the ability or capacity to do work. human body are burnt, a lot of chemical energy is released.
The S.I unit of work done and energy is a joule (J).
b) Nuclear energy:
Sources of energy: This is the energy released when atomic nuclei disintegrate
The raw material for the production of energy is called the during nuclear reactions.
energy source. In nuclear reactions, the energy, which holds the nuclear
There are two types of energy sources. particles together (Binding energy), is released.
©[email protected] 42
There are two types of nuclear reactions i.e. fission (Where Conservation of Energy.
large nuclei break to form smaller ones) and fusion (Where The principle of conservation of energy:
smaller nuclei combine to form larger ones). In both cases, It states that ‘energy is neither created nor destroyed’ but
large amounts of energy are released. can be changed from one form to another.

c) Electrical energy (Electricity): In any system, the total original energy is equal to the total
This is the form of energy which is due to electric charges final energy. For example, electrical energy is changed to
moving from one point of a conductor to another. light energy in the bulb. However, the bulb also feels hot
This form of energy is most easily converted to other forms, because some of the energy is changed to heat.
making it the most useful form. Therefore, light energy plus the heat energy is equal to the
electrical energy supplied.
d) Light energy: Thus from this principle, we conclude that;
This is the form of energy which enables us to see. Light is  No new energy is created
part of a wider spectrum of energy called the  Total existing energy is not destroyed
electromagnetic spectrum. Light consists of seven visible  Energy is only changed from one form to another.
colours, of red, orange, yellow, green, blue, indigo and
violet. We are able to see because the eye is sensitive to the As energy is changed from one form or state to another, an
colours. energy converter (Device) is required to ease the conversion.
Examples of such devices are shown in the table below.
e) Heat energy: Energy Change Converter
Heat is a form of energy, which results from random Chemical to electrical Cells or Batteries
movement of the molecules in the body. Light to Electrical Solar panels
It is responsible for changes in temperature. Electrical to light Electric lamps e.g bulbs
When a body is heated or when heat energy of the body Electrical to heat Cooker or flat iron, etc.
increases;
Heat to Electrical Thermocouple
(i) The internal kinetic energy of the molecules
Electrical to sound Loud speakers
increases leading to a rise in temperature.
Sound to Electrical Microphones
(ii) The internal potential energy of molecules
increases leading to expansion and change of state Electrical to Kinetic Electric motors
of the body. Kinetic to Electrical Electric generators

f) Sound energy: Conservation of mechanical energy:

This is the energy which enables us to hear. P.ET= mgh, K.E.= 0
Like light, sound is also a form of wave motion, which
makes particles to vibrate. Our ears are able to detect sound
because it produces vibrations in the ear.
g) Mechanical energy: P.E1 + K.E1= P.ET.
This is the energy of motion. P.E1= mgh1
Mechanical energy = kinetic energy + Potential energy h K.E1= P.ET – P.E1
h1 = mgh – mgh1
There are two forms of mechanical energy.
(i) Kinetic energy:- This is the energy possessed by a
body due to its velocity or motion. 1
P.E= 0, K.E.= mv 2 = mgh
1 2
Kinetic energy = (mass)×(velocity)2
2
1
K.E = mv2
2 A body of mass m at a height h above the ground, has a
potential energy, P.E = mgh. At this point, the velocity of
(ii) Potential energy:- This is the energy possessed by a
the body is 0ms-1 hence it has no kinetic energy. (K.E. = 0J).
body due to its position or condition.
It is equal to the work done in putting the body in that
When the body is released, it begins to fall with an
position or condition.
acceleration g. The velocity of the body thus increases as the
A body above the earth’s surface has an amount of
height, h decreases. The body therefore gains kinetic energy
gravitational potential energy equal to the work done against
at the expense of potential energy.
gravity.
Weight is the force of gravity acting on a body.
When the body is just reaching the ground, the height, h is
Weight = mg.
zero (h = 0m) while its velocity is given by;
𝑣 2 = 𝑢2 + 2𝑎𝑠; 𝑤ℎ𝑒𝑟𝑒 𝑠 = ℎ, 𝑎 = 𝑔 𝑎𝑛𝑑 𝑢 = 0
Gravitational 𝐚𝐜𝐜𝐞𝐥𝐞𝐫𝐚𝐭𝐢𝐨𝐧
( ) = (mass)× ( ) 𝑣 2 = 02 + 2𝑔ℎ
Potential energy 𝐝𝐮𝐞 𝐭𝐨 𝐠𝐫𝐚𝐯𝐢𝐭𝐲
𝐇𝐞𝐢𝐠𝐡𝐭 𝐚𝐛𝐨𝐯𝐞 𝑣 2 = 2𝑔ℎ
×( ) 𝒗 = √𝟐𝒈𝒉
𝐭𝐡𝐞 𝐠𝐫𝐨𝐮𝐧𝐝
Thus, its kinetic energy as it reaches the ground is given
1 1 2
P.E = mgh by; K. E = mv 2 = m(√2gh) = mgh
2 2

©[email protected] 43
 𝟏
Hence, 𝐊. 𝐄 = 𝐦𝐯 𝟐 = 𝐦𝐠𝐡 K.E=0.2×10×20
𝟐
K.E=40J
Therefore; 𝐆𝐚𝐢𝐧 𝐢𝐧 𝐊. 𝐄 = 𝐋𝐨𝐬𝐬 𝐢𝐧 𝐏. 𝐄.
(iii)
As it hits the concrete, Total P.E is converted to K.E
The above illustration shows that energy is conserved. 1
Mechanical energy is continually transformed between K.E= m𝑣 2 = mgh
kinetic and potential energy. 2
(h=height from which the ball is dropped)
1
A swinging pendulum. m𝑣 2 = mgh
The transformation of energy between kinetic and potential 2
𝑣 2 = 2gh.
energy can also be seen in a swinging pendulum.
v = √2gh
At the end (extremes) of the swing, the energy of the v = √2(10)(20)
pendulum bob is only potential. v = √400
v = 20𝑚𝑠 −1
As it passes the central position, it has only kinetic energy.
(iv)
In other positions between the extreme ends and the central As the bounces from the concrete, the K.E used to move the
position, it has both potential and kinetic energies. it from the bottom to the height h1 is converted to P.E at
h1 and it is momentarily at rest.
1
Support K.E1 = mv21 = mgh1
2
(ℎ1 =height to which the ball bounces).
K.E1 =0.2(10)(5)
K.E1 =10J

Only P.E (v)

Only P.E As the bounces from the concrete, the K.E used to move it
from the bottom to the height h1 is converted to P.E at
P.E + K.E h1 and it is momentarily at rest.
P.E + K.E
Only K.E 1
K.E1 = mv21 = mgh1
2
Mechanical energy = P.E + K.E (ℎ1 =height to which the ball bounces).
1
(0.2)v21 =0.2(10)(5)
2
As the bob falls from the left towards the central position, it 0.1v21 = 10
2
gains K.E at the expense of P.E. v1 = 100
𝑣1 = √100
As it rises from the central position towards the left end, it 𝑣1 = 10𝑚𝑠 −1
gains P.E at the expense of K.E.
(vi) As it falls from the top, Total P.E at the top is
Example: converted to some K.E and some P.E in
A ball of mass 200g falls freely from a height of 20m above Falling to the height h1 .
the ground and hits a concrete floor and rebounds to a height 1
of 5m. Given that g = 10ms-1, find the; K.ET = mv21 + mgh1
2
(h1 =height of the ball from ground).
i) P.E of the ball before it fell. 1
ii) Its K.E. as it hits the concrete. 40= (0.2)v21 + 0.2(10)(5)
2
iii) Velocity with which it hits the concrete. 40= 0.1v21 + 10
iv) K.E as it rebounds. 30= 0.1v21
v) Velocity with which it rebounds. v21 = 300
vi) Velocity when it has fallen through a height of 15m.
𝑣1 = √300
v1 = 17.32ms −1
Solution:
(i)
Example 1:
P.E=mgh (h=height from which the ball is dropped)
Calculate the kinetic energy of a 2Kg mass trolly traveling
P.E=0.2×10×20
at 400m per second.
P.E=40J
𝐺𝑖𝑣𝑒𝑛; 𝑚 = 2𝑘𝑔, 𝑣 = 400𝑚𝑠 −1
1
(ii) K.E= m𝑣 2
As it hits the concrete, Total P.E is converted to K.E 2
1
1 K.E= (2)(400)2
K.E= m𝑣 2 = mgh 2
2 K.E=160,000J
(h=height from which the ball is dropped)

©[email protected] 44
Example 2:
A 5Kg mass falls from a height of 20m. calculate the
potential energy lost.
R
𝐺𝑖𝑣𝑒𝑛; 𝑚 = 5𝑘𝑔, ℎ = 20𝑚
P.E=𝑚𝑔ℎ
P.E=5(10)(20) P.E = mgh
P.E=1000J

Example 3: mg
A 200g ball falls from a height of 0.5m. Calculate its kinetic h
energy just before hiting the ground.
200
𝐺𝑖𝑣𝑒𝑛; 𝑚 = 200𝑔 = = 0.2𝑘𝑔, ℎ = 0.2𝑚 K.E = (mg-R)h
1000
K.E gained = P.E lost K.E gained=(mg-R)h
K.E=mgh
K.E=0.2(10)(0.5) K.E gained=(20×10 - 0.9)×1.8
K.E=1J =(200 - 0.9)×1.8
=(199.1)×1.8
Exercise: K.E gained =358.38J
1. A block of mass 2 kg falls freely from rest through a
distance of 3m. (ii) Calculate energy lost due to air resistance
i) Find the K.E of the block. (Ans: =60J) Total energy at h,=mgh
K.E gained = P.E lost =20×10×1.8
ii) Potential energy (Ans: =60J) Total energy at h,=360J
iii) The velocity with which the body hits the ground. (K.E
gained = P.E lost). Energy lost due to air resistance=360J-358.38J
Energy lost due to air resistance=1.62J
2. A body falls freely through 3m. Calculate the velocity
with which it hits the ground. (Ans: = 7.75ms-1) Note:
Energy lost due to air resistance can also be calculated from;
3. 100g steel ball falls from a height of 1.9m on a plate and Energy lost due to air resistance=Work done against R
rebounds to a height of 1.25m. Find the; Energy lost due to air resistance=Force × Height
Energy lost due to air R=Air resistance × Height
(i) P.E of the ball before the fall. (Ans: =1.8J) =0.9×1.8
(ii) Its K.E. as it hits the plate. (Ans: =1.8J) Energy lost due to air R=1.62J
(iii) Its velocity on the plate. (Ans: =6ms-1)
(iv) Its K.E as it leaves the plate on rebound. (Ans: =1.25J)
(v) Its velocity of rebound. (Ans: =5ms-1) Calculating the kinetic energy at any point for a body
falling freely.
For a body not falling freely but as it falls it experiences air
resistance then the kinetic energy gained by the body just A P.E= mgh
before it hits the ground is calculated from: K.E= 0
𝐊. 𝐄 𝐠𝐚𝐢𝐧𝐞𝐝 = (𝐦𝐠 − 𝐑)𝐡

Where mg is the weight of the body, R is the air resistance B P.E T .= P.E 1 + K.E 1
and h is the height above the ground. P.E 1 = mgh 1
h mgh = mgh 1 + K.E 1
Example 4:
A 20kg body falls from 1.8m above the ground. If the air h1
resistance is 0.9N.
(i) Calculate the kinetic energy just before hitting the 𝟏
P.E= 0, K.E.= 𝒎𝒗𝟐 = 𝒎𝒈𝒉
ground. 𝟐

At A the body has all potential energy. So the energy at A is

Solution
mgh = Total energy.
𝐺𝑖𝑣𝑒𝑛; 𝑚 = 20𝑘𝑔, 𝑅 = 0.9𝑁, ℎ = 1.8𝑚, 𝐾. 𝐸. =?
At B the body has a mixture of kinetic energy and potential
energy.
P.ET =K.E1 + P.E1
mgh=K.E1 + mgh1
1
mgh= mv21 + mgh1
2
Where “h1” is the height above the ground.

©[email protected] 45
Example 5: 1:7:3. POWER
A stone of 150g is dropped from a height of 80m. Power is the rate of doing work. Or
Calculate the; Power is the rate of transfer of energy.
(i) Kinetic energy when it is 50m above the ground. Note: Work done is the same as energy transferred.

Solution: 𝐖𝐨𝐫𝐤 𝐝𝐨𝐧𝐞 Energy transfered

150 𝐏𝐨𝐰𝐞𝐫 = =
m=150g= =0.15kg, h1 =50m, h=80m. 𝐓𝐢𝐦𝐞 𝐭𝐚𝐤𝐞𝐧 Time taken
1000

A Where work done=Force × Distance

F×d d
30cm Power = = F × = FV
t t
𝐏𝐨𝐰𝐞𝐫 = 𝐅. 𝐕
Where V is the velocity of the body.
80cm 𝐦𝐠𝐡
𝐏𝐨𝐰𝐞𝐫 =
50cm 𝐭

Where mg is the weight of the body and h the height.

The S.I unit of power is watt (W).

1watt=1Js-1
(i) Method 2 :
mgh = K.E1 + mgh1 Given; a=10ms-2 , u=0ms-1 ,h=30m, v=?
Definition:
0.15(10)(80)=K.E1 + 0.15(10)(50) Where h is the height
A watt is the rate of transfer of energy of one joule per
120=K.E1 + 75 fallen through.
second.
K.E1 =120 - 75 Or It is the rate of doing work of 1joule in one second.
K.E1 =45J Then using the third
equation of motion, we
Example 1:
(ii) Its velocity when its 50m have;
An engine raises 20kg of water through a height of 50m in
above the ground. ဎ2 = 𝑢2 + 2𝑎ℎ 10 seconds. Calculate the power of the engine.
𝑣 2 = 02 + 2(10)(30) Solution:
Method 1 : 𝑣 2 = 600
1 𝑣 = √600 𝑚𝑠 −1 mgh
K.E1 = mv21 Power =
2 𝑣 = 24.49 𝑚𝑠 −1 t
1
45= ×0.15×v21 20(10)(50)
2 Power =
90=0.15v21 10
Power
600 =v21 = 1000W
√600 = 𝑣1
𝑣1 = 24.49𝑚𝑠 −1 Example 2:
An electric bulb is rated 100W. How much electrical energy
(iii) Its kinetic energy when it has fallen through 50m. does the bulb consume in 2hours.
Given; g=10ms-2 , h=80, h1 =(80-50)=30m, K.E=? Solution:
Where h is the height above the ground.
Then from; Energy used
mgh = K.E1 + mgh1 Power =
time taken
0.15(10)(80)=K.E1 + 0.15(10)(30)
120=K.E1 + 45 Energy used
K.E1 =120 - 745 100 =
2 × 60 × 60
K.E1 =75J
Enery used = 100(2 × 60 × 60)
Enery used = 720,000J

Example 3:
A man uses an electric motor whose power output is 3000W
for 1hour. If the motor consumes 1.44×107 J of electricity in
that time, find the efficiency of the motor.
Solution:
Given;Pout =3000W, t=1hr=1×60×60=3600s.
Energyinput =1.44×107 J

Energy input
power input =
time taken

©[email protected] 46
 iii) Some of the energy is also wasted in lifting useless loads
Ein like pistons.
Pin =
t
Qn1:
1.44×107 A pulley system of V.R six is used to lift a load of 250N
Pin = through a distance of 3m. If the effort applied is 50N,
36000
calculate how much energy is wasted.
Pin = 4000W
Qn2: A girl of mass 40kg runs up a stair case in 16 seconds.
Power output If each stair case is 20 cm high and she uses 100 Js −1 . Find
Efficiency = × 100% the number of stairs. [Ans: 20]
Power input

3000 See UNEB

Efficiency = × 100% 1994 Qn. 17 2006 Qn.7
4000
1989 Qn. 29 1997 Qn.5
Efficiency = 75% 2007 Qn.33 1995 Qn.9
1987 Qn.3 and Qn.24 1991 Qn.11
For machines 1993 Qn.4 and 18 1992 Qn.11
1997 Qn.10 2003 Qn.15
Power input is the power created by effort. 1999 Qn.2 and Qn.8 2007 Qn.6
Work input Effort × Effort Distance 2000 Qn.23 1993 Qn.4
Power input= = 2001 Qn.26 2005 Qn.45
Time taken Time taken

Power output is the power created by the load.

Work output Load × Load Distance
Power output= =
Time taken Time taken

Example 4:
An effort of 250N raises a load of 1000N through 5m in 10
seconds. If the velocity ratio is five, Calculate the:
i) Power input
ii) Efficiency
Solution:
Power Work output
( )=
(i) Given; input Time taken
Effort=250N, Load=1000N,
V.R=5, L.D=5m, t=10s Load×Load Distance
=
Time taken
E.D E.D
V.R= ⟺ 5= 1000×5
L.D 5 =
E.D=25m 10
Power output = 500 W
Power Work input
( )=
input Time taken (ii)
Power
( )
Effort×Effort Distance output
= Eff = × 100%
Time taken Power
( )
input
250×25 500
= Efficiency = × 100%
10 625
Power input=625 W Efficiency = 80%

INTERNAL COMBUSTION ENGINE

A heat engine is a machine, which changes heat energy
obtained by burning fuel to kinetic energy (mechanical
energy)

Engines are always less than 100% efficient because:-

i) Some of the energy is lost in over coming friction between
walls of the cylinder and pistons.
ii) Some heat energy is lost to surrounding due to
conduction.

©[email protected] 47
 A box of dimensions 20cm by 1m by10cm weighs 30kg.
Determine the maximum and minimum pressures exerted by
the box on the ground.

1: 8 PRESSURE Given: -Dimensions; cm x 10cm x 20cm

-Mass, m = 30kg
Pressure is the force acting normally per unit area of the -Acceleration due to gravity, g = 10ms-2
surface.
𝐅𝐨𝐫𝐜𝐞(𝐍)
𝑖. 𝑒 𝐏𝐫𝐞𝐬𝐬𝐮𝐫𝐞 =
𝐀𝐫𝐞𝐚(𝐦𝟐 ) 10cm

The S.I unit of pressure is

a newton per square metre, (N⁄m2 or 𝐍𝐦−𝟐 ) or 20cm
a pascal(𝐏𝐚). 1m

Given:
A pascal is the pressure exerted when a force of 1N acts
-Dimensions; 1m x 2m x 3m
normally on an area of 𝟏 𝐦𝟐 .
-Mass, m = 30kg
-Acceleration due to gravity, g = 10ms-2
1:8:1. PRESSURE IN SOLIDS:
Force, F = Weight
Pressure in solids depends on;
= mg
 Magnitude of force applied
F = 30 × 10
 Cross sectional area in contact
F = 300N
Smallest Smallest Next smaller
Maximum and Minimum Pressure ( )=( )×( )
Area length length
Pressure increases when the area decreases and decreases 10 20
when the area increases. Amin = ( × ) = 0.02m2
Force or weight 𝐅 100 100
Thus:Maximum Pressue = ∶ i. e. 𝐏𝐦𝐚𝐱 =
Minimum Area 𝐀𝐦𝐢𝐧
F 300
Force or weight 𝐅
Then: Pmax = = = 15000 Nm−2 or 15000 Pa
Minimum Pressue = ∶ i. e. 𝐏𝐦𝐢𝐧 = Amin 0.02
Maximum Area 𝐀𝐦𝐚𝐱

Longest Next longer

Example 1: Largest Area = ( )×( )
length length
The box below weighs 60N. Determine the maximum and 20
minimum pressures it exerts on the ground. Amax = (1 × ) = 0.2m2
100

F 300
1m Pmin = = = 1500 Nm−2 or 1500 Pa
Amax 0.2

Example 3:
2m The dimension of a cuboid are 5cm x 10cm x 20cm and the
3m
mass of the cuboid is 6kg. Calculate the maximum and
Solution minimum pressures the cuboid exerts on the ground.
Given: Solution
-Dimensions; 1m x 2m x 3m Given: - Dimensions; 5cm x 10cm x 20cm
-Force, F=W = 60N -Mass, m = 6kg
-Acceleration due to gravity, g = 10ms-2 -Acceleration due to gravity, g = 10ms-2
Force, F = Weight
F = 60N
Smallest Smallest Next smaller 5cm
( )=( )×( )
Area length length
Amin = (1 × 2) = 2m2
F 60
Then: Pmax = = = 30 Nm−2 or 30 Pa 10cm
Amin 2 20cm

Longest Next longer

Largest Area = ( )×( ) F
length length) Then: Pmax =
2 Amin
Amax = (3 × 2) = 6m
F 60
Pmin = = = 10 Nm−2 or 10 Pa Force, F = Weight
Amax 6
F = mg
F = 6(10)
F = 60N
Example 2: Smallest Smallest Next smaller
( )=( )×( )
Area length length

©[email protected] 48
 30 20
Vw = × × 0.5
5 10 1 100 1000
Amin = ( × )= m2 = 0.005 m2 Vw = 0.003m−3
100 100 200

F 60 F = 2.5 × 10 + (0.003) × (1000) × 10

Pmax = = = 12000 Nm−2 or 12000 Pa F = 25 + 30
Amin 0.005 F = 50N
Longest Next longer
Largest Area = ( )×( )
length length 50 50
Pmax = = = 8333.33Nm−2 or 8333.33 Pa
20 10 1 2 0.006 0.006
Amax = ( × )= m = 0.02 m2
100 100 50 50
F 60 Pmin = = 333.33 Nm−2 or 333.33Pa
Pmin = = = 3000Nm−2 or 3000 Pa 0.15
Amax 0.02
(iii) When half filled with water.
Force, F = (Weight ofempty tank) + (weight of water)
F = mt g + mw g
Example 4: F = mt g + Vw ρw g
The tank below has a mass of 2.5kg. Determine the Where Volume of water, Vw = l × w × h
minimum and maximum pressure exerted by the tank on the 30 20
ground; When it is; Vw = × × 0.25
100 1000
−3
(i) empty Vw = 0.0015m
(ii) filled with water up to the brim.
(iii) half filled with water. (Density of water =1000kgm-3) Then, F = 2.5 × 10 + (0.0015) × (1000) × 10
F = 25 + 15
F = 40N
0.5m
40
Pmax = = 666.67Nm−2 or 666.67Pa
0.006
20mm
30cm 40
Pmin = = 266.67Nm−2 or 266.67Pa
0.15
Solution
(i) When empty Note: when calculating pressure, the unit of area of base
Given: - Dimensions; 5cm x 10cm x 20cm should always be in m2. From the above calculations it is
-Mass, m = 2.5kg noted that: the greater the area over which the force acts
-Acceleration due to gravity, g = 10ms-2 normally the less is the pressure.
Force, F = Weight
F = mg  A tractor with wide wheels can pass over soft ground
F = 2.5 × 10 because the greater area of wide wheel exerts less
F = 25N pressure.
 A hippopotamus of wide feet is able to walk on soft
Smallest Smallest Next smaller grounds without sinking because the greater area of
( )=( )×( )
Area length length wide hooves exerts less pressure.

20 30  When the same force is applied on a needle and nails

Amin = ( × ) = 0.006m2
1000 100 both placed on the hand, one tends to feel more pain
from the needle because the small area of needle exerts
F 25 greater pressure.
Pmax = = = 4166.67Nm−2 or 4166.67 Pa
Amin 0.006
 A sharp knife cuts well than a blunt one.
Longest Next longer
Largest Area = ( )×( )
length length Exercise:
1. Explain the following observations;
30 (i) A large reservoir is much wider at the base than at the top
Amax = (0.5 × ) = 0.15m2 (ii) In supply of water, smaller pipes are preferred to larger
100
ones.
F 25 2. A rectangular block of metal weighs 5 N and measures
Pmin = = = 166.67Nm−2 or 166.67 Pa 2 cm × 3 cm × 4 cm. What is the least pressure which it
Amax 0.15
can exert on a horizontal surface?
(ii) When filled with water to the brim A. 2.10 × 10-7 Pa B. 4.17 × 10-5 Pa
-5
Force, F = (Weight ofempty tank) + (weight of water) C. 6.25 × 10 Pa D. 8.30 × 10-5 Pa
F = mt g + mw g
F = mt g + Vw ρw g 3. See UNEB
Where Volume of water, Vw = l × w × h 1994. Qn.25 1991. Qn.5
2003. Qn.10 1995. Qn.15
©[email protected] 49
 1999. Qn.33 1996. Qn.39
Straw
1988. Qn.13 2002. Qn9

Bottle
1: 8 :2. PRESSURE IN FLUIDS: Atmospheric Pressure

ATMOSPHERIC PRESSURE
The layer of air surrounding the earth is called the
atmosphere.
Atmospheric pressure is the pressure exerted by the weight
of air on all objects on the earth’s surface. b) Rubber sucker
When the sucker is moistened and pressed on a smooth flat
Atmospheric Pressure depends on altitude. surface, the air is pushed out. Atmospheric pressure then
The density of air above the earth decreases as the altitude holds it firmly against the surface.
increases leading to the decrease of atmospheric pressure at Suckers are used for attaching car licenses to windscreen
high altitude and the vice versa. At sea level, the and in industry for lifting metal sheets.
atmospheric pressure is 1.0 × 105 Pa.
Defining pressure in fluids
Though the value of atmospheric pressure is large we do Fluids refer to gas or liquids. These take up the shape of the
not normally feel it because: container, so the volume of the liquid filling a cylindrical
-Blood pressure is slightly greater than atmospheric pressure container is equal to the volume of that cylindrical
-Atmospheric pressure acts equally in all direction. container.
Area of base = πr 2
Experiments to Demonstrate Existence of Atmospheric Volume of liquid = πr 2 h
Pressure. Mass of liquid = πr 2 hρ
a) Collapsing Can or Crushing Can Experiment.
Weight of liquid = πr 2 hρg
If air is removed from the can by a vacuum pump, the can h
collapses because the air pressure inside becomes less than
the atmospheric pressure.

Area of base = πr 2
Cold Water

Steam Atmospheric
pressure pressure Cork
Then from the definition of pressure:

Force(N) (πr 2 )hρg

Pressure = = = hρg
Area(m2 ) (πr 2 )
Atmospheric
pressure
𝐏𝐫𝐞𝐬𝐬𝐮𝐫𝐞 = 𝐡𝛒𝐠
Heat
Properties of fluids related to pressure

 A small quantity of water is boiled in a can until steam (i) A liquid finds its own level:
forms. Pressure in liquids does not depend on cross sectional area
 The steam drives out all the air inside the can, hence and shape of vessel containing the liquid.
reducing the pressure inside the can. This can be illustrated by an experiment using a
 The stopper is then tightly fitted onto the can and the communicating tube as shown below.
heat source removed.
 Cold water is then poured over the can. This causes the Tubes of different
steam inside to condense producing water and water Cross sectional area Liquids surfaces in all the tubes
vapour at very low pressure. and shape at the same level
 The excess atmospheric pressure outside the can causes
it to collapse inwards.

Importance of atmospheric pressure

a) Drinking straw
When sucking, lungs expand and air is driven out from the h
inside of the straw to the lungs.
This reduces the pressure inside the straw.
Then atmospheric pressure acting on surface of the liquid in A liquid is poured into the communicating tubes of different
the bottle is greater than air pressure in straw and so it forces cross-sectional areas.
the liquid up to the mouth.

©[email protected] 50