CMD v4 Basic Error Codes
CMD v4 Basic Error Codes
CMD Messages
The two-digit codes on CMD controllers indicate the following error messages:
Error
Meaning Explanation
code
Off No power supply Switch on the device.
- Start-up (after RESET or electronics self-
Wait until start-up is complete.
- test)
b
Burn; program controller Contact service.
u
C
Compare; check controller Contact service.
O
Controller OK -
O
0
No error -
0
0
Software faulty Switch the device off and on.
1
Perform a reset using the function button.
0 Communication problem with Chip
If error message ‘05’ does not disappear,
5 card controller
contact customer service.
Communication problem with Chip Perform a reset using the function button.
0
card / or wrong Chip card inserted If error message ‘06’ does not disappear,
6
(Chip card number not ‘226-0PR’) contact service.
0
Stacker EEPROM missing/defective Contact service.
8
Push the CMD-V4as far as possible into the
device using the green locking handle
0 Locking handle open, CMD is not in
(CMD-V4 must audibly click into place). If
9 dispensing position
error message ‘09’ does not disappear,
contact customer service.
1
Controller faulty Contact service.
0
Perform a reset using the function button.
1
No software(download) If error message ‘11’ does not disappear,
1
contact service.
1
Safely switch open Insert the CMD-V4.
2
Remove banknote bundles from the CMD-
V4.
1 Reset the device lock using the product
Device disable present
3 specific software (see chapter “Basic
Operation”, section “Calling the product
specific software”).
Insert and log in cassette (one
1 CMD-V4 minimum configuration is
reject/retract cassette and one cash out
4 missing
cassette required).
1 Cassette board with invalid coding, not
Contact service.
5 inserted, or defective
INNOVATIVE PVT LTD. ERROR CODES & OTHERS
1
Output transport coding invalid Contact service
6
1
Belt drive of clamp defective Contact service
7
Check the cash paths in the stacker, in the
area of the stacker wheels and in the
dispenser modules (see section “Checking
1 the cash paths”).
Banknotes jammed during dispensing
8 Move the CMD-V4 in the safe to the cash-
out position and wait for the system to
boot. If error message ‘18’ does not
disappear, contact service.
Check the cash paths in the output
transport (see section “Checking the cash
1 paths”). Move the CMD-V4 in the safe to
Clamp transport defective / blocked
9 the cash-out position and wait for the
system to boot. If error message ‘19’ does
not disappear, contact service
Check the cash paths in the output
transport (see section “Checking the cash
2 Single reject switch (MA2/1, MA2/2,
paths”). Move the CMD-V4 in the safe to
0 SM1) faulty blocked
the cash-out position and wait for the
system to boot.
2
Faulty measuring station(DDU) Contact service.
1
Clear the cash paths (see section
“Checking the cash paths”).
Move the CMD-V4 in the safe to the cash-
2 Photo sensor amplifier faulty or photo out position and wait for the system to
2 sensor initialization unsuccessful. boot. If error message ‘22’ does not
disappear, perform a reset using the
function button. If you do this three times
without success, contact service
If you cannot pull out CMD-V4, perform a
reset using the function button. If error
message ‘23’ does not disappear, contact
customer service. If you can pull out the
CMD-V4, check the cash paths in the
2 Routing disk (SM2/SM3) stacker and output transport (see section
3 defective/blocking “Checking the cash paths”).
Move the CMD-V4 in the safe to the cash-
out position and wait for the system to
reboot. In other cases, please contact
service.
Displays at startup
NO. Meaning Reaction
OFF No power supply Switch on the device
.8 Controller faulty Replace the controller
.8
- - Controller test after power on None
0 to 9 (displays are flashing and keep
changing)
b Warning: Battery too weak Replace battery (controller)
E
1 Controller faulty Replace the controller
0
- Startup of firmware (reset) None
- Validation of firmware Error 11
Check of CMOS parameter Initialization of photo
Test of mechanical components senses
Clearing run CMOS
Error Ps xx, 22
Error 23 …28
Error 18,19,71..9A
P X Error during photo senses Check and clear photo sensor
5 X initializing after change of xx, try RESET capital again.
configuration or replacement of Replace module or controller if
controller (the display necessary
alternates between ‘PS’ and the
photo sensor ‘XX’)
0 Power up completed without
0 errors
INNOVATIVE PVT LTD. ERROR CODES & OTHERS
12 Error Code:
CDM ERROR: 0000001D 20001812 00000000
Reason: Safety switch Lock is open. (CMD has not been inserted completely)
Measure: Dispenser inserted properly and Position is Dispenser back and left side switch.
09 Error Code:
CDM ERROR: 0000001D 20001809 00000000
Reason: Safety switch Lock is open Dispenser is not properly inserted. (Service switch is
open)
Measure: Dispenser inserted Properly Locking handle Switch open, Check it Dispenser is in
dispensing
Position.
10 Error Code:
CDM ERROR: 0000001D 20001810 00000000
Reason: CMD electronics faulty. Battery empty or battery jumper not connected:
Measure: Only with self-test commands for battery testing Mount battery jumper or replace
battery. And Dispenser power Off for 5 to 10 mint then ON if again display 10 error then
final CMD Controller Replaced if battery avail then first battery replace.
01 Error Code:
CDM ERROR: 0000001D 20001801 00000000
Reason: Software faulty (No response from the CDM Software)
Measure: Switch the Dispenser device power off for 5 to 10mint then On. If still issue then
again upgrade the updated Firmware after upgrade Firmware again error on display then
CMD Controller replaced.
11 Error Code:
CDM ERROR: 0000001D 20001811 00000000
Reason: Firmware missing in the CMD).
Measure: Restart ATM and Download Firmware if not downloading firmware then check
Firmware File available at this path {Pro base>CSCW32>FRM>----} if not available then file
copy from Data DVD-V5 and again paste at {Pro base>CSCW32>FRM>----} and restart ATM
and see it dispenser LED and Initializing FRM loaded status on main display screen.
05 Error Code:
CDM ERROR: 0000001D 20001805 00000000
Reason: Communication problem with the chip card.
INNOVATIVE PVT LTD. ERROR CODES & OTHERS
Measure: Check CMD all Cables then Restart CMD Final Replace the chip card Controller.
06 Error Code:
CDM ERROR: 0000001D 20001806 00000000
Reason: Communication problem with the chip card.
Measure: Check CMD all Cables then Restart CMD Final Replace the chip card Controller.
08 Error Code:
CDM ERROR: 0000001D 20001808 00000000
Reason: Communication problem with the Stacker EE-PROM collector.
Measure: Check EE-PROM Cable from Jack and Reset Controller CL and final replace EE-
PROM.
13 Error Code:
CDM ERROR: 0000001D 20001813 00000000
Reason: The maximal number of retracts has been reached A Retract has been executed.
The cash was not
Removed by the customer from Clamp again or Shutter Problem then Transactions
Retracted
Measure: Remove the customer money from the retract box and transport path using
operator function. And then reset the device and Clear Retract 50 Vendor Menu >> 04 Clear
Retracts>>01 ok.
14 Error Code:
CDM ERROR: 0000001D 20001814 00000000 .
Reason: Minimum configuration missing. In order to operate, the CDM requires at least one
reject/retract cassette and one cash-out cassette. The device is not ready for operation.
Cassette Missing Error.
Measure: Insert the cassettes and log on Cassettes Command Run using operator function.
50 Vendor Menu >>03 Logon Cassette >>01 ok.
15 Error Code:
CDM ERROR: 0000001D 20001815 00000000
Reason: Cassette distributor board has invalid coding, is not inserted or defective
Measure: Check the cabling to the distribution board to CMD Controller damage or not
plugged cable. If again appear error then <CL> CMD Controller and also appear then Board
Replaced.
16 Error Code:
CDM ERROR: 0000001D 20001816 00000000
Reason: Output transport coding invalid
Measure: Check it output Transport cable jack and sensor and also Clamp Cable and If again
appear error then
<CL> CMD Controller and also appear then output tray Replaced.
17 Error Code:
CDM ERROR: 0000001D 20001817 00000000
INNOVATIVE PVT LTD. ERROR CODES & OTHERS
18 Error Code:
CDM ERROR: 0000001D 20001818 00000000
Reason: Note jam during dispensing Cash not accessible by customer
Measure: Cash Jam at may be many places therefore, Check the note path from the
cassettes to the collecting tray. Whole Dispenser Service include VSAT fully service check it
all Roller SP polar, gears. If all Hardware OK then still issue 18 errorthen also check it
Cassettes internal Gear that is free then CL Controller and again Counter Run.
19 Error Code:
CDM ERROR: 0000001D 20001819 00000000
CDM ERROR: 00006434 0000004D 00000000
CDM ERROR: 0000643A 00000000 0000FFF2
Reason: Gripper/Clamp transport defective/blocked
Measure: Any Breakage in cable then Banknote jam in output transport. Eliminate the
blockage and check it Clamp cable properly then reset CMD. If necessary, replace stacker or
Clamp cable and also check it reject cassette.
20 Error Code:
CDM ERROR: 0000001D 20001820 00000000
Reason: Single reject switch (MA2/1, MA2/2, SM 1) faulty/blocked
Measure: Cash available in single reject collect it and check it CASH. Cash is not proper
shuffled and unsorted. Dispensing Module more then one Note pick from cassette at one
time and Note block at single reject. And also check it Spring in single reject below position.
Select test function 2 (mechanical test) by pressing the function button, and observe
actuation of the single reject switch. If lifting magnet MA2 does not move at all or all the
way, the stacker and output transport (SAT) or the controller has to be replaced. If the
magnet moves all the way, the CMD-V4 can go back into
operation.
21 Error Code:
CDM ERROR: 0000001D 20001821 00000000
Reason: Measuring station is defective
Measure: Check whether there is a banknote jam in the area of the measuring station. Are
the cables connected and also Clean it MS Points now again appear then CL Controller also
again appear then Replace MS.
22 Error Code:
CDM ERROR: 0000001D 20001822 00000000
Reason: Photo sensor amplifier faulty or photo sensor initialization unsuccessful. (MS)
Measure: Measuring station is defective Faulty Many Transaction is not Supported Weak
MS Power Now
Replace Required MS
INNOVATIVE PVT LTD. ERROR CODES & OTHERS
23 Error Code:
CDM ERROR: 0000001D 20001823 00000000
Reason: Routing disk defective/blocked (SM 2/SM 3) Circle switch faulty/blocked
Measure: Clamp pull out From SAT (Routing Disk) check all gear, builds’, and motor free
moved and Clean it and also check it both Router Disk Position same.
if position not same adjust it disk. All checked then insert it Clamp and Set the CMD-V4 in
the safe to cash-out position (safety switch closed) and select test function 2 (mechanical
test) If this test function once again ends
with status display '23' Then CL Controller again face '23' then Replace Stacker
24 Error Code:
CDM ERROR: 0000001D 20001824 00000000
Reason: Reject/retract drive defective/blocked (MA 6)
Measure: Reinsert the Reject/retract cassette, select test function 2 by pressing the function
button, and check the movement of the Reject/retract drive (MA6). Reject/retract
Compartment Sensor Block, Dusty, or Position change Clean and adjust it {DPS4,5,6,,HS3
Sensor clean it}.
25 Error Code:
CDM ERROR: 0000001D 20001825 00000000
Reason: Dispensing drive defective (DCM 1) Cash Jam
Measure: If Dispensing Module is not rotate properly or Jam it then check it Whole
Dispensing path maybe Cash Jam with {Rubber, Pin} in dispensing module.
Clean it path whole dispenser service include whole VSAT and clean <U> Sensor position is
left side of SAT Wheel rod and also check it Cassettes internal Gear that is free. if again
appear error then <CL> CMD Controller and also appear then STACKER Replaced.
26 Error Code:
CDM ERROR: 0000001D 20001826 00000000
Reason: Stacker wheel drive defective/blocked (SM 9)
Measure: Stacker wheels and main motor check it. Check the Stacker in the area of the
collecting tray for jammed banknotes/scraps, remove it. Set the Dispenser own position and
select test function 2 (mechanical test) on the function button after starting up the
Dispenser test if this test function once again ends with status display '26', then CL
Controller if again appear then Stacker or Main Motor must be replaced.
28 Error Code:
CDM ERROR: 0000001D 20001828 00000000
CDM ERROR: 00006434 00000000 00000020
Reason: Shutter Faulty Almost < U > Sensor Problem DPS10, DPS11
Measure: Whole Shutter properly Services. Shutter Prism two glass clear surfaces opposite
the (transmitter/receiver) Shutter Sensor DPS10, DPS11, PS26, PS27 Reset and test CMD
Controller <1,2> or
<CL> CMD Controller if again issue still then Replace Shutter
INNOVATIVE PVT LTD. ERROR CODES & OTHERS
29 Error Code:
CDM ERROR: 0000001D 20001829 00000000
CDM ERROR: 0000643A 00000000 0000FFF2
CDM ERROR: 0000643A 00000000 0000FECE Also maybe cash finished
CDM ERROR: 00006434 00000000 00000020
Reason: Shutter Faulty Photo sensor Problem Dusty or Position Changed PS26, PS27.
Measure: Whole Shutter properly Services. Shutter Prism two glass clear surfaces opposite
the (transmitter/receiver) Shutter Sensor PS26, PS27 Reset and test CMD Controller <1,2> or
<CL> CMD Controller if again issue still then Replace Shutter.
31 Error Code:
CDM ERROR: 0000001D 20001831 00000000
Reason: Too many problems during dispensing from cassette # 1 x (x = 1)
Measure: 1. Remove the cassette from dispensing unit x=1 and check internal Gear that is
free and check the inserted banknotes that is ok placed in cassette and sorted it
2. VSAT 1st part straight 1st cassette check it all gears SP Polar Sensors and also Clutch
Motor.
32 Error Code:
CDM ERROR: 0000001D 20001832 00000000
Reason: Too many problems during dispensing from cassette # 2 x (x = 2)
Measure: 1. Remove the cassette from dispensing unit x=2 and check internal Gear that is
free and check the inserted banknotes that is ok placed in cassette and sorted it
2. VSAT 2nd part straight 2nd cassette check it all gears SP Polar Sensors and also Clutch
Motor.
Same Procedure 33, 34 Error Code Like Cassette 3,4
41 Error Code:
CDM ERROR: 0000001D 20001841 00000000
Reason: Cash could not be dispensed or possibly faulty amount of pressure against the
banknotes when a new cassette is inserted # 1 (x = 1)
Measure: 1. Remove the cassette 'x=1' and check the inserted banknotes: the notes must be
standing upright in the cassette. Are the first notes very crumpled? Curved notes should
bend away from the pressure carriage! Are the first notes stuck to each other or jammed
together?
2. When the cassette is removed, check the dispensing area in the dispensing unit for
jammed banknotes/scraps.
1. Remove the cassette from dispensing unit x=1 and check internal Gear that is free and
check the inserted
Banknotes that is ok placed in cassette and sorted it
2. VSAT 1st part straight 1st cassette checks it all gears SP Polar Sensors and also Clutch
Motor.
42 Error Code:
CDM ERROR: 0000001D 20001842 00000000
Reason: Cash could not be dispensed or possibly faulty amount of pressure against the
banknotes when a new cassette is inserted # 2 (x = 2)
INNOVATIVE PVT LTD. ERROR CODES & OTHERS
Measure: 1. Remove the cassette 'x=2' and check the inserted banknotes: the notes must be
standing upright in the cassette. Are the first notes very crumpled? Curved notes should
bend away from the pressure carriage! Are the first notes stuck to each other or jammed
together?
2. When the cassette is removed, check the dispensing area in the dispensing unit for
jammed banknotes/scraps.
1. Remove the cassette from dispensing unit x=2 and check internal Gear that is free and
check the inserted
Banknotes that is ok placed in cassette and sorted it
2. VSAT 2nd part straight 2nd cassette check it all gears SP Polar Sensors and also Clutch
Motor.
Same Procedure 43,44 Error Code Like Cassette 3,4.
51 Error Code:
CDM ERROR: 0000001D 20001851 00000000
Reason: Too many bad banknotes from cassette # 1 (x =1)
Measure: Too many double or excessively wide/narrow notes were detected during
dispensing from cassette x. Remove cassette x=1, and check whether the right type of
banknote was inserted. Check notes for sticky points. Reinsert the cassette and restart the
application. If many 'good' notes are subject to a single reject during dispensing or if error
‘51’ shows after a short time, the reference values should be recalculated for this
Note type. If the error cannot be removed, Then the dispensing unit Part check/Replace or
Cassette Replace.
1. Remove the cassette from dispensing unit x=1 and check internal Gair that is free and
check the inserted banknotes that is ok placed in cassette and sorted it
2. VSAT 1st part straight 1st cassette checks it all gears SP Polar Sensors and also Clutch
Motor.
52 Error Code:
CDM ERROR: 0000001D 20001852 00000000
Reason: Too many bad banknotes from cassette # 2 (x = 2)
Measure: Too many double or excessively wide/narrow notes were detected during
dispensing from cassette x.
Remove cassette x=2, and check whether the right type of banknote was inserted. Check
notes for sticky points. Reinsert the cassette and restart the application. If many 'good'
notes are subject to a single reject during dispensing or if error '52' show after a short time,
the reference values should be recalculated for this note type. If the error cannot be
removed, Then the dispensing unit Part check/Replace or Cassette Replace.
1. Remove the cassette from dispensing unit x=2 and check internal Gear that is free and
check the inserted banknotes that is ok placed in cassette and sorted it
2. VSAT 2nd part straight 2nd cassette check it all gears SP Polar Sensors and also Clutch
Motor.
Same Procedure 53,54 Error Code Like Cassette 3,4
61 Error Code:
CDM ERROR: 0000001D 20001861 00000000
Reason: Cassette defective # 1(x = 1) Cassette not properly initialized cassette faulty.
INNOVATIVE PVT LTD. ERROR CODES & OTHERS
Measure: The banknote data stored in cassette 'x=1' cannot be read or rewritten (Write
error cassette EEPROM). Check internal cable of cassette and also check and clean Pressure
sensor Verify that the connectors on CMD controller and the cassette connector are plugged
in properly. If the fault also occurs with a different cassette in this dispensing unit, then
Cassette must be replaced.
.
62 Error Code:
CDM ERROR: 0000001D 20001862 00000000
Reason: Cassette defective # 2 (x = 2) Cassette not properly initialized cassette faulty.
Measure: The banknote data stored in cassette 'x=2' cannot be read or rewritten (Write
error cassette
EEP ROM). Check internal cable of cassette and also check and clean Pressure sensor
Verify that the connectors on CMD controller and the cassette connector are plugged in
properly. If the fault also occurs with a different cassette in this dispensing unit, the Cassette
must be replaced.
Same Procedure 63,64 Error Code Like Cassette 3,4.
70 Error Code:
CDM ERROR: 0000001D 20001870 00000000
Reason: Banknote thickness measuring station (DDU/MS) not ready
Measure: Check whether there is a banknote jam in the area of the measuring station and
also check it CASH
Status in cassettes maybe cash thicked (jam) in cassette
71 Error Code:
CDM ERROR: 0000001D 20001871 00000000
Reason: Dispensing sensor (Pressure sensor (PSD x=1) ) is dirty or faulty Cassette # 1 (x = 1)
Measure: If a cassette can be inserted without error (single acoustic signal) ok status, If a
cassette can be
Inserted with error (many acoustic signal and error show 72) then Dispenser sensor
(Pressure sensor PSD x=1) photo sensor in dispenser module 'x=1' which must be cleaned.
Then execute a Reset "01" through push button of Controller if again error show then CL
clear CMOS CMD Controller if again still issue then Distribution Board Replaced
If Cassettes inserted status fine/ok and TEST CASH Run and Show error 71 then check it first
Cassette internal Gear (free move it) if gear ok moveable then Distribution Board Replaced.
72 Error Code:
CDM ERROR: 0000001D 20001872 00000000
Reason: Dispensing sensor (Pressure sensor (PSD x=2) ) is dirty or faulty Cassette # 2 (x = 2)
Measure: If a cassette can be inserted without error (single acoustic signal) ok status, If a
cassette can be inserted with error (many acoustic signal and error show 72) then Dispenser
sensor (pressure sensor PSD x=2) photo sensor in dispenser module 'x=2' which must be
cleaned. Then execute a Reset "01" through push button of Controller if again error show
then CL clear CMOS CMD Controller if again still issue then Distribution Board Replaced. If
Cassettes inserted status fine/ok and TEST CASH Run and Show error 72 then check it first
Cassette internal Gear (free move it) if gair ok moveable then Distribution Board Replaced.
Same Procedure 73,74 Error Code Like Cassette 3,4
INNOVATIVE PVT LTD. ERROR CODES & OTHERS
81 Error Code:
CDM ERROR: 0000001D 20001881 00000000
Reason: Cassette empty sensors (4 photo and 2 pressure) is dirty (x = 1)
Measure: Clean photo sensor 'PSE x' in the relevant dispensing unit and the associated
prism in the pressure carriage of the cassette # 1. Then execute a Reset or CL CMD. Closed
sensor that is Cash empty sensor if again appear error then Distribution Board Replaced
Required
82 Error Code:
CDM ERROR: 0000001D 20001882 00000000
Reason: Cassette empty sensors (4 photo and 2 pressure) is dirty (x = 2)
Measure: Clean photo sensor 'PSE x' in the relevant dispensing unit and the associated
prism in the pressure carriage of the cassette # 2. Then execute a Reset or CL CMD. Closed
sensor that is Cash empty sensor if again appear error then Distribution Board Replaced
Required
Same Procedure 83,84 Error Code Like Cassette 3,4.
91 Error Code:
CDM ERROR: 0000001D 20001891 00000000
CDM ERROR: 0000643A 00000000 0000FFF2
CDM ERROR: 0000643A 00000000 0000FECE Also maybe cash finished
CDM ERROR: 00006434 00000000 00000020
Reason: Photo sensor dirty Cassette monitoring: Photo sensor PS18 Sensor, Shutter Sensor
PS26, PS27.
Measure: Clean Sensor position is Below of Main STACKER Wheel.
Whole Shutter properly Services. Prism two glass clear surfaces opposite the
(transmitter/receiver) Shutter Sensor PS26, PS27 Reset and test CMD Controller <1,2> or
<CL> CMD Controller if again issue still then
Replace Shutter.
93 Error Code:
CDM ERROR: 0000001D 20001893 00000000
CDM ERROR: 0000643A 00000000 0000FFF2
CDM ERROR: 0000643A 00000000 0000FECE Also maybe cash finished
CDM ERROR: 00006434 00000000 00000020
Reason: Shutter Faulty Almost Photo sensor Problem Dusty or Position Changed {Cassette
empty' (single reject) PS2}
Measure: Whole Shutter properly Services. Shutter Prism two glass clear surfaces opposite
the (transmitter/receiver) Shutter Sensor PS26, PS27 Reset and test CMD Controller <1,2> or
<CL> CMD Controller if again issue still then Replace Shutter.
95 Error Code:
CDM ERROR: 0000001D 20001895 00000000
CDM ERROR: 0000643A 00000000 0000FFF2
CDM ERROR: 0000643A 00000000 0000FECE Also maybe cash finished
CDM ERROR: 00006434 00000000 00000020
INNOVATIVE PVT LTD. ERROR CODES & OTHERS
Reason: Shutter Faulty Photo sensor Problem Dusty or Position Changed {PS26, PS27}
Measure: Whole Shutter properly Services. Shutter Prism two glass clear surfaces opposite
the (transmitter/receiver) Shutter Sensor PS26, PS27 Reset and test CMD Controller <1,2> or
<CL> CMD Controller if again issue still then Replace Shutter
28 Error Code:
CDM ERROR: 0000001D 20001828 00000000
CDM ERROR: 00006434 00000000 00000020
Reason: Shutter Faulty Almost < U > Sensor Problem DPS10, DPS11
Measure: Whole Shutter properly Services. Shutter Prism two glass clear surfaces opposite
the (transmitter/receiver) Shutter Sensor DPS10, DPS11, PS26, PS27 Reset and test CMD
Controller <1,2> or <CL> CMD Controller if again issue still then Replace Shutter
29 Error Code:
CDM ERROR: 0000001D 20001829 00000000
CDM ERROR: 0000643A 00000000 0000FFF2
CDM ERROR: 0000643A 00000000 0000FECE Also maybe cash finished
CDM ERROR: 00006434 00000000 00000020
Reason: Shutter Faulty Photo sensor Problem Dusty or Position Changed PS26, PS27.
Measure: Whole Shutter properly Services. Shutter Prism two glass clear surfaces opposite
the (transmitter/receiver) Shutter Sensor PS26, PS27 Reset and test CMD Controller <1,2> or
<CL> CMD Controller if again issue still then Replace Shutter
CDM ERROR: 00006434 0000004D 00000000 Show error code on Dispenser is 17,19 code
Reason: Gripper/Clamp transport defective/blocked
Measure: Check it any Breakage in cable, Banknote jam in output transport path. Eliminate
the blockage and check it Clamp cable properly then reset CMD and also check it Reject
cassette status manual press reject cassette button in Stacker and also check it Whole
Shutter. If necessary, replace stacker or Clamp cable.
Measure: Whole Shutter properly Services. Shutter Prism two glass clear surfaces opposite
the (transmitter/receiver) Shutter Sensor PS26, PS27 Reset and test CMD Controller <1,2> or
<CL> CMD Controller if again issue still then Replace Shutter
SMR 0 AF 21 FDD anti-skimming process cannot work properly because it is not enabled
FDD anti-skimming cannot work properly because device does not have HW
SMR 0 AF 20
capability
FDD anti-skimming process cannot work properly because device reports ESR
SMR 0 AF 10
sensor failure