TEC Electronic Cash Register

MA-600 SERIES
Programming Manual
Document No. EO3-11106

Original Dec., 2005

(Revised )

PRINTED IN JAPAN

Downloaded from www.Manualslib.com manuals search engine

 EO3-11106

TABLE OF CONTENTS

Page
1. INTRODUCTION .........................................................................................................1- 1
1.1 Main Features ...............................................................................................................1- 1
1.2 Description of Model Number ........................................................................................1- 1

2. SPECIFICATIONS ......................................................................................................2- 1
3. CAPACITIES...............................................................................................................3- 1
3.1 Indexing Capacities .......................................................................................................3- 1
3.2 Basic Memory Capacities ..............................................................................................3- 2
3.3 Financial Memory ..........................................................................................................3- 3
3.4 Cashier Memory ............................................................................................................3- 6
3.5 Others ...........................................................................................................................3- 8
3.6 Memory Balance............................................................................................................3- 9

4. SYSTEM START-UP PROCEDURE...........................................................................4- 1

5. RAM CLEAR, DATA CLEAR, STATUS CLEAR ........................................................5- 1
5.1 RAM Clear.....................................................................................................................5- 1
5.2 DATA Clear ...................................................................................................................5- 2
5.3 STATUS Clear...............................................................................................................5- 3

6. TERMINAL FILE PROGRAMMING ............................................................................6- 1

6.1 Instructions for Programming.........................................................................................6- 2
6.2 Character Entries...........................................................................................................6- 7
6.3 Condition Required for Programming Operations .........................................................6-13
6.4 SFKC (Selective Function Key Code) Programming .....................................................6-14
6.5 System Option Programming........................................................................................6-18
6.6 Commercial Message Programming.............................................................................6-49
6.7 Footer Message Programming .....................................................................................6-52
6.8 Store Name Message Programming.............................................................................6-55
6.9 Department Name Programming ..................................................................................6-59
6.10 Department Group Name Programming .......................................................................6-61
6.11 Cashier Name and Status Programming.......................................................................6-63
6.12 PLU Name Programming..............................................................................................6-66
6.13 Salesperson Name Programming .................................................................................6-68
6.14 Financial Report Item Name Programming ...................................................................6-71
6.15 Print Line Item Name Programming..............................................................................6-77
6.16 Display Item Name Programming .................................................................................6-83
6.17 Error Item Name Programming.....................................................................................6-87
6.18 Read/Reset Report Name Programming ......................................................................6-93
6.19 Department Table Programming...................................................................................6-98
6.20 Department Preset Price Setting or Changing ............................................................6-104

Downloaded from www.Manualslib.com manuals search engine

 EO3-11106

Page
6.21 Department Listing Capacity (LC) Programming.........................................................6-106
6.22 Key Sticker Printing ....................................................................................................6-109
6.23 PLU Table Programming ............................................................................................6-113
6.24 PLU Preset Price Setting or Changing........................................................................6-120
6.25 PLU Preset-Code Key Setting ....................................................................................6-123
6.26 %+ and %- Preset Rate Setting ..................................................................................6-128
6.27 VAT or Add-on Tax Rate Setting ................................................................................6-130
6.28 Foreign Currency Exchange Rate Setting...................................................................6-132
6.29 Negative Amount Key Limit Amount Setting ...............................................................6-135
6.30 Time Setting or Adjustment ........................................................................................6-137
6.31 Date Setting or Adjustment.........................................................................................6-138
6.32 Store/Register No. Setting ..........................................................................................6-140
6.33 Hourly Range Table Setting........................................................................................6-142
6.34 Tone Volume Setting ..................................................................................................6-146
6.35 Report Item Print/Non-Print Setting.............................................................................6-148
6.36 Key Status Programming............................................................................................6-153
6.37 Cash Tender Key Preset Amount Setting ...................................................................6-157
6.38 Drawer Warning Time Setting.....................................................................................6-159
6.39 Special Rounding Process Setting, 1-digit type...........................................................6-161
6.40 Special Rounding Process Setting, 2-digit type...........................................................6-163
6.41 Number of Receipt Print Buffer Line Setting ...............................................................6-166
6.42 Serial No. Setting........................................................................................................6-168

7. VERIFICATION OF PROGRAMMED DATA...............................................................7- 1

CAUTION!
1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC.
2. The contents of this manual may be changed without notification.
3. Please refer to your local Authorised Service representative with regard to any queries you may have in
this manual.

Copyright © 2005
by TOSHIBA TEC CORPORATION
All Rights Reserved
570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN

Downloaded from www.Manualslib.com manuals search engine

 1. INTRODUCTION EO3-11106

1.1 Main Features

1. INTRODUCTION
This programming manual is provided for salespersons, field engineers, and other personal as supplementary
manual for TOSHIBA TEC Electronic Cash Register MA-600 series.
Reading through the MA-600 Owner’s Manual is recommended in order to thoroughly understand the
descriptions in this manual.

1.1 Main Features

• This ECR adopts an LCD display (192 x 64 dots), which displays a maximum of 24 one-byte characters by 4
lines.
• A PC is connectable to the ECR with USB connection.
• Files for up to 40 departments, 1000 PLUs, and 8 cashiers can be controlled.
• Consignment print feature is supported. (Immediately after performing the Department/PLU entry or finalizing
a sale, the [CONSIGNMENT] key depression leads to an issuance of a receipt only for the entry or sale
finalization just performed.)
• Key-in tone at the registering operation and error tone are selectable from High (standard setting), Low, and
OFF.
• Key sticker printing feature is adopted.

1.2 Description of Model Number

1.2.1 Terminal Model Number

MA-600- - - - R

RoHS Compliance
Blank: Non-RoHS compliant model
R: RoHS compliant model

Destination Code
(QP, GB, etc.)

Drawer Type
G: ESP drawer

Keyboard Type
Blank: Normal type keyboard
F: Flat type keyboard

Series
2: QP type

1- 1

Downloaded from www.Manualslib.com manuals search engine

 2. SPECIFICATIONS EO3-11106

2. SPECIFICATIONS

2. SPECIFICATIONS
SIZE: 410 mm (width) x 442 mm (depth) x 291 mm (height)
(height including rubber feet)
Height when the customer display is fully raised: 351 mm

WEIGHT: Approximately 13.6Kg

POWER REQUIREMENT: AC 220 V to AC 230 V ±10 %; 50/60 Hz ±10 % (QP model)

AC 230 V ±10 %; 50/60 Hz ±10 % (GB model)
AC 240 V ±10 %; 50/60 Hz ±10 % (AU model)
(varies depending on the destination)

POWER CONSUMPTION: Standby: 8.2 W (0.08 A), Operating: 35 W (0.23 A)

BATTERY:
Type ----------------------------------------------------- Lithium-vanadium battery
Life ------------------------------------------------------- 5 years
Back-up duration ------------------------------------- 1 month (in case of full charge)
Charge method --------------------------------------- Inserting the power plug into an outlet
Full charge time--------------------------------------- 48 hours or more

AMBIENT TEMPERATURE: 0°C to 40°C

RELATIVE HUMIDITY: 10 % to 90 % (No condensation)

PRINTER:
Model ---------------------------------------------------- FTP-628MCL113 (FUJITSU)
Number of stations ----------------------------------- 2 stations (Receipt and Journal)
Print method ------------------------------------------- Thermal direct printing
Effective print width ---------------------------------- 48 mm
Total Number of dots -------------------------------- 384 dots/line
Dot pitch ------------------------------------------------ 0.125 mm (8 dots/mm)
Dot size ------------------------------------------------- 0.125 mm x 0.12 mm
Print speed --------------------------------------------- Max. 60 mm/sec.
Printable digits ---------------------------------------- 32 one-byte characters per line
Character components------------------------------ 12 (width) x 24 (height) dots
Character spacing------------------------------------ 0 mm (No space)
Line spacing ------------------------------------------- 3.6 mm/line
Character size (one-byte character) ------------- 1.5 mm (W) x 3.0 mm (H)
Receipt cutting method ----------------------------- Manual cutting
Size of store name logo----------------------------- 48 mm (W) x 15 mm (H)
384 dots (W) x 120 dots (H)
Paper loading method------------------------------- Drop-in method

2- 1

Downloaded from www.Manualslib.com manuals search engine

 2. SPECIFICATIONS EO3-11106

2. SPECIFICATIONS

PAPER ROLL (RECEIPT and JOURNAL)

Media ---------------------------------------------------- Thermal roll paper
Width ---------------------------------------------------- 58 +0/-1 mm
Thickness----------------------------------------------- 0.060 mm to 0.075 mm
Outside dimension ----------------------------------- 80 mm or less
Recommended thermal paper -------------------- Only paper rolled onto a core is acceptable, however, the
paper end should not be pasted to the core.
Standard paper:
TF60KS-E (Nippon Paper Industries)
PD150R (Oji Paper Co., Ltd)
High-sensitive paper:
TF50KS-E4 (Nippon Paper Industries)
Medium-term preserving paper:
TP60KS-F1 (Nippon Paper Industries)
P220VBB-1 (MITSUBISHI PAPER MILLS LIMITED)
PD170R (Oji Paper Co., Ltd)
Long-term preserving paper:
TP50KJ-R (Nippon Paper Industries)
PD152R (Oji Paper Co., Ltd)
PD160R-N (Oji Paper Co., Ltd)
AFP-235 (MITSUBISHI PAPER MILLS LIMITED)
HA220AA (MITSUBISHI PAPER MILLS LIMITED)

DISPLAY:
Operator Display
Upper row ---------------------------------------------- LCD display (192 x 64 dots)
SET, X, Z BLIND mode: 24 one-byte characters x 4 lines
REG, MGR, - mode: 16 one-byte characters x 2 lines
Lower row ---------------------------------------------- 10-digit 7-segment fluorescent display
Display colour: Amount portion (Green)
DPT and X portions (Yellow)
Conditions (Red and Green)
Amount-------------------------------------------------- 8 digits (7 digits for registering)
Department code: 2 digits
Repeat count: 1 digit

Customer Display
Lower row ---------------------------------------------- 7-digit 7-segment fluorescent display
Display colour: Amount portion (Green)
Conditions (Red and Green)
Amount-------------------------------------------------- 7 digits

KEYBOARD:
Number of keys --------------------------------------- Ordinary type keyboard: max. 66 keys
Flat type keyboard: max.106 keys
Mode Lock --------------------------------------------- 8 positions

DRAWER:
The size of the drawer and the specifications of the money case vary depending on the individual product
standard.
Drawer-open detector ------------------------------- Provided

2- 2

Downloaded from www.Manualslib.com manuals search engine

 3. CAPACITIES EO3-11106

3.1 Indexing Capacities

3. CAPACITIES
3.1 Indexing Capacities
Input Item Digits Remarks
Amount 7
Quantity in Multiplication 6 3 integer digits + 3 decimal digits (0.001 to 999.999)
Unit Price in Multiplication 6
Tender Media Keys 8
Non-add Number 18
Percent Rate 5 2 integer digits + 3 decimal digits (0.001 to 99.999%)
VAT Rate 4 2 integer digits + 2 decimal digits (0.01 to 99.99%)
PLU Code 4
2-digit cashier’s own secret code (01 to 99) + 2-digit manager-
Cashier Code 4
assign code (01 to 08)
Salesperson Code 2 1 to 30
Department Code 2 1 to 40
Group Code 2 1 to 15

3- 1

Downloaded from www.Manualslib.com manuals search engine

 3. CAPACITIES EO3-11106

3.2 Basic Memory Capacities

3.2 Basic Memory Capacities

(NOTE: For Item Count below, “6 + 2 digits” means that it has 6 integer digits and 2 decimal digits.)

Group Memory (Group Name: 12 characters; max. 15 groups)

Memory Type Counter or Total Digits
Item Count 6+2
Amount 10
Daily Memory
Item Count 6+2
Group Total
Amount 10
Item Count 6+2
Amount 10
GT Memory
Item Count 6+2
Group Total
Amount 10

Department Memory (Department Name: 16 characters; max. 40 departments)

Memory Type Counter or Total Digits
Customer Count 6
Daily Memory Item Count 6+2
Amount 10
Customer Count 6
GT Memory Item Count 6+2
Amount 10

PLU Memory (PLU Name: 16 characters; max. 1000 PLUs)

Memory Type Counter or Total Digits
Item Count 6+2
Daily Memory
Amount 10

Hourly Range Memory (max. 24 hour ranges)

Memory Type Counter or Total Digits
Customer Count 6
Daily Memory Item Count 6+2
Amount 10

Salesperson Memory (Salesperson Name: 12 characters; max. 30 salespersons)

Memory Type Counter or Total Digits
Item Count 6+2
Gross Sale
Amount 10
Item Count 6+2
Daily Memory Net Sale with Tax
Amount 10
Item Count 6+2
Return
Amount 10

3- 2

Downloaded from www.Manualslib.com manuals search engine

 3. CAPACITIES EO3-11106

3.3 Financial Memory

3.3 Financial Memory

Counter Daily GT
Name of Total/Counter Counter Total Counter Total Remarks
Type Digits Digits Digits Digits
GT (Grand Total) 16 (16) Non-resettable
NET GT (All-media Sales GT) 16 (16) Non-resettable
NEG GT 16 (16) Non-resettable
GS (Gross Sale) ITEM 6+2 10 6+2 10
Tax 1 to Tax 8 8 x 10 8 x 10
Tax Total 10 10
Net Sale with Tax ITEM 6+2 10 6+2 10
%+ (% I) ENTRY 6 10 6 10
%- (% II) ENTRY 6 10 6 10
Vender Coupon ENTRY 6 10 6 10
Amount Discount ENTRY 6 10 6 10
Negative Departments Total ITEM 6+2 10 6+2 10
Special Rounding 10 10
All-media Sales CUS 6 10 6 10
Cash Sales CUS 6 10 6 10
Cheque Sales CUS 6 10 6 10
Credit Sales CUS 6 10 6 10
Misc. Media Sales CUS 6 10 6 10
Media-Coupon Sales CUS 6 10 6 10
Credit 1 Sales CUS 6 10 6 10
Credit 2 Sales CUS 6 10 6 10
Credit 3 Sales CUS 6 10 6 10
Credit 4 Sales CUS 6 10 6 10
Credit 5 Sales CUS 6 10 6 10
Received-on Account ENTRY 6 10 6 10
Paid-Out ENTRY 6 10 6 10
Cash-in-drawer 10
Cash-in-drawer
(Foreign Currency 1) 10
Cash-in-drawer
(Foreign Currency 2) 10
Cash-in-drawer
(Foreign Currency 3) 10
Cash-in-drawer
(Foreign Currency 4) 10
Cash-in-drawer
(Foreign Currency 5) 10

-- continued on the next page --

3- 3

Downloaded from www.Manualslib.com manuals search engine

 3. CAPACITIES EO3-11106

3.3 Financial Memory

Financial Memory: (continued)

Counter Daily GT
Name of Total/Counter Counter Total Counter Total Remarks
Type Digits Digits Digits Digits

Cheque-in-drawer ENTRY 6 10
Cheque-in-drawer
(Foreign Currency 1) ENTRY 6 10
Cheque -in-drawer
(Foreign Currency 2) ENTRY 6 10
Cheque -in-drawer
(Foreign Currency 3) ENTRY 6 10
Cheque -in-drawer
(Foreign Currency 4) ENTRY 6 10
Cheque -in-drawer
(Foreign Currency 5) ENTRY 6 10

Credit-in-drawer ENTRY 6 10
Credit-in-drawer
(Foreign Currency 1) ENTRY 6 10
Credit-in-drawer
(Foreign Currency 2) ENTRY 6 10
Credit-in-drawer
(Foreign Currency 3) ENTRY 6 10
Credit-in-drawer
(Foreign Currency 4) ENTRY 6 10
Credit-in-drawer
(Foreign Currency 5) ENTRY 6 10

Misc. Media-in-drawer ENTRY 6 10

Misc. Media-in-drawer
(Foreign Currency 1) ENTRY 6 10
Misc. Media -in-drawer
(Foreign Currency 2) ENTRY 6 10
Misc. Media -in-drawer
(Foreign Currency 3) ENTRY 6 10
Misc. Media -in-drawer
(Foreign Currency 4) ENTRY 6 10
Misc. Media -in-drawer
(Foreign Currency 5) ENTRY 6 10

Media-Coupon-in-drawer ENTRY 6 10
Media-Coupon-in-drawer
(Foreign Currency 1) ENTRY 6 10
Media-Coupon-in-drawer
(Foreign Currency 2) ENTRY 6 10
Media-Coupon-in-drawer
(Foreign Currency 3) ENTRY 6 10
Media-Coupon-in-drawer
(Foreign Currency 4) ENTRY 6 10
Media-Coupon-in-drawer
(Foreign Currency 5) ENTRY 6 10

Credit 1-in-drawer ENTRY 6 10

Credit 2-in-drawer ENTRY 6 10
Credit 3-in-drawer ENTRY 6 10
Credit 4-in-drawer ENTRY 6 10
Credit 5-in-drawer ENTRY 6 10
Cash-in-drawer Difference 10 at Money Declaration
Cheque-in-drawer Difference 10 at Money Declaration
-- continued on the next page --

3- 4

Downloaded from www.Manualslib.com manuals search engine

 3. CAPACITIES EO3-11106

3.3 Financial Memory

Financial Memory: (continued)

Counter Daily GT
Name of Total/Counter Counter Total Counter Total Remarks
Type Digits Digits Digits Digits

Credit-in-drawer Difference 10 at Money Declaration

Misc. Media-in-drawer Difference 10 at Money Declaration
Media-Coupon-in-drawer Difference 10 at Money Declaration
Credit 1-in-drawer Difference 10 at Money Declaration
Credit 2-in-drawer Difference 10 at Money Declaration
Credit 3-in-drawer Difference 10 at Money Declaration
Credit 4-in-drawer Difference 10 at Money Declaration
Credit 5-in-drawer Difference 10 at Money Declaration
Item Correct ENTRY 6 10 6 10 Item Correct on DP+/PLU+

Void ENTRY 6 10 6 10 Void on DP+/PLU+

Misc. Void ENTRY 6 10 6 10 Item Correct on others
All Void ENTRY 6 10 6 10
Store Coupon ITEM 6 10 6 10
Returned Merchandise ITEM 6+2 10 6+2 10
Negative Mode ( - ) Total ENTRY 6 10 6 10
%- on Line Items ENTRY 6 10 6 10
Amount Discount on Line Items ENTRY 6 10 6 10
Transfer Balance GT 10 (10) Non-resettable
Transfer + GT 10 (10) Non-resettable
Transfer - GT 10 (10) Non-resettable
Transfer + Daily 10 10
Transfer - Daily 10 10
Previous Balance CUS 6 10 6 10
Previous Balance R/A 10 10 Payments made for PB
Previous Balance PO 10 10 PB refunded to customers
Taxable Total 1 to 8 8 x 10 8 x 10
VAT 1 to 8 8 x 10 8 x 10
VAT Total 10 10
Net Sale without Tax 10 10
Tax-exempted Customer CUS 6 6
VAT 1 to 8 Exempt 8 x 10 8 x 10
Net Sale Item Count per
ITEM 6+2 6+2
Customer
All-media Sales per Cus. 10 10
No-sale Counter ENTRY 6
Clear Key Counter ENTRY 6
Consignment Key Counter ENTRY 6
Validation Counter ENTRY 6

3- 5

Downloaded from www.Manualslib.com manuals search engine

 3. CAPACITIES EO3-11106

3.4 Cashier Memory

3.4 Cashier Memory

Counter Daily GT
Name of Total/Counter Counter Total Counter Total Remarks
Type Digits Digits Digits Digits

GS (Gross Sale) ITEM 6+2 10 6+2 10

Net Sale with Tax ITEM 6+2 10 6+2 10
%+ (% I) ENTRY 6 10 6 10
%- (% II) ENTRY 6 10 6 10
Vender Coupon ENTRY 6 10 6 10
Amount Discount ENTRY 6 10 6 10
Negative Departments Total ITEM 6+2 10 6+2 10
All-media Sales CUS 6 10 6 10
Cash Sales CUS 6 10 6 10
Cheque Sales CUS 6 10 6 10
Credit Sales CUS 6 10 6 10
Misc. Media Sales CUS 6 10 6 10
Media-Coupon Sales CUS 6 10 6 10
Credit 1 Sales CUS 6 10 6 10
Credit 2 Sales CUS 6 10 6 10
Credit 3 Sales CUS 6 10 6 10
Credit 4 Sales CUS 6 10 6 10
Credit 5 Sales CUS 6 10 6 10
Received-on Account ENTRY 6 10 6 10
Paid-Out ENTRY 6 10 6 10
Cash-in-drawer 10
Cash-in-drawer
(Foreign Currency 1) 10
Cash-in-drawer
(Foreign Currency 2) 10
Cash-in-drawer
(Foreign Currency 3) 10
Cash-in-drawer
(Foreign Currency 4) 10
Cash-in-drawer
(Foreign Currency 5) 10

Cheque-in-drawer ENTRY 6 10
Cheque-in-drawer
(Foreign Currency 1) ENTRY 6 10
Cheque -in-drawer
(Foreign Currency 2) ENTRY 6 10
Cheque -in-drawer
(Foreign Currency 3) ENTRY 6 10
Cheque -in-drawer
(Foreign Currency 4) ENTRY 6 10
Cheque -in-drawer
(Foreign Currency 5) ENTRY 6 10

-- continued on the next page --

3- 6

Downloaded from www.Manualslib.com manuals search engine

 3. CAPACITIES EO3-11106

3.4 Cashier Memory

Cashier Memory: (continued)

Counter Daily GT
Name of Total/Counter Counter Total Counter Total Remarks
Type Digits Digits Digits Digits

Credit-in-drawer ENTRY 6 10
Credit-in-drawer
(Foreign Currency 1) ENTRY 6 10
Credit-in-drawer
(Foreign Currency 2) ENTRY 6 10
Credit-in-drawer
(Foreign Currency 3) ENTRY 6 10
Credit-in-drawer
(Foreign Currency 4) ENTRY 6 10
Credit-in-drawer
(Foreign Currency 5) ENTRY 6 10

Misc. Media-in-drawer ENTRY 6 10

Misc. Media-in-drawer
(Foreign Currency 1) ENTRY 6 10
Misc. Media -in-drawer
(Foreign Currency 2) ENTRY 6 10
Misc. Media -in-drawer
(Foreign Currency 3) ENTRY 6 10
Misc. Media -in-drawer
(Foreign Currency 4) ENTRY 6 10
Misc. Media -in-drawer
(Foreign Currency 5) ENTRY 6 10

Media-Coupon-in-drawer ENTRY 6 10
Media-Coupon-in-drawer
(Foreign Currency 1) ENTRY 6 10
Media-Coupon-in-drawer
(Foreign Currency 2) ENTRY 6 10
Media-Coupon-in-drawer
(Foreign Currency 3) ENTRY 6 10
Media-Coupon-in-drawer
(Foreign Currency 4) ENTRY 6 10
Media-Coupon-in-drawer
(Foreign Currency 5) ENTRY 6 10

Credit 1-in-drawer ENTRY 6 10

Credit 2-in-drawer ENTRY 6 10
Credit 3-in-drawer ENTRY 6 10
Credit 4-in-drawer ENTRY 6 10
Credit 5-in-drawer ENTRY 6 10
Cash-in-drawer Difference 10 at Money Declaration
Cheque-in-drawer Difference 10 at Money Declaration
Credit-in-drawer Difference 10 at Money Declaration
Misc. Media-in-drawer Difference 10 at Money Declaration
Media-Coupon-in-drawer Difference 10 at Money Declaration
Credit 1-in-drawer Difference 10 at Money Declaration
Credit 2-in-drawer Difference 10 at Money Declaration
Credit 3-in-drawer Difference 10 at Money Declaration
Credit 4-in-drawer Difference 10 at Money Declaration
Credit 5-in-drawer Difference 10 at Money Declaration
-- continued on the next page --

3- 7

Downloaded from www.Manualslib.com manuals search engine

 3. CAPACITIES EO3-11106

3.5 Others

Cashier Memory: (continued)

Counter Daily GT
Name of Total/Counter Counter Total Counter Total Remarks
Type Digits Digits Digits Digits

Item Correct ENTRY 6 10 6 10 Item Correct on DP+/PLU+

Void ENTRY 6 10 6 10 Void on DP+/PLU+

Misc. Void ENTRY 6 10 6 10 Item Correct on others
All Void ENTRY 6 10 6 10
Returned Merchandise ITEM 6+2 10 6+2 10
Negative Mode ( - ) Total ENTRY 6 10 6 10
No-sale Counter ENTRY 6
Clear Key Counter ENTRY 6
Consignment Key Counter ENTRY 6
Validation Counter ENTRY 6
Money Declaration Counter ENTRY 6
Read Report Counter ENTRY 4
Reset Report Counter ENTRY 4

3.5 Others
Counter Daily GT
Name of Total/Counter Counter Total Counter Total Remarks
Type Digits Digits Digits Digits
Hourly Range Reset Counter ENTRY 4
PLU Reset Counter ENTRY 4 4
Department Reset Counter ENTRY 4 4
Financial Read Counter ENTRY 4 4
Financial Reset Counter ENTRY 4 4
Salesperson Reset Counter ENTRY 4

3- 8

Downloaded from www.Manualslib.com manuals search engine

 3. CAPACITIES EO3-11106

3.6 Memory Balance

3.6 Memory Balance

1. GT (Grand Total) = Sum of Daily GS (Gross Sale)

2. NET GT = Sum of Daily Net Sales

3. NEG GT = GT – NET GT

4. GS (Gross Sale) = (Sum of Positive Depts) + (Sum of Add-on Taxes) NOTE 1

5. Net Sale = GS – (Sum of Negative Depts) + (%+) – (%-) – (Vender Coupon)

– (Amount Discount) + (Special Rounding Fraction) NOTE 2
= (Cash Sales) + (Sum of all other media sales) + (Previous Balance Sales)
= (Sum of Hourly Sales)… If Financial Reset Report and Hourly Range Reset Report are taken at the

same time.

6. Negative Mode Total = (Net Sale + Received-on-Account + Paid-Out ) in Negative Mode

7. Net Sale without Tax (N.NS) = (Net Sale) – (Sum of VATs)…applicable only when the VAT feature is selected

8. Net Sale Item Count per Customer = (Item Count of Net Sale) ÷ (Customer Count of All-media Sales)
All-media Sales per Customer = (Amount of All-media Sales) ÷ (Customer Count of All-media Sales)

NOTES: 1. Applicable only when the Add-on Tax feature is selected.

2. Special Rounding Fraction amounts for Received-on-Account and Paid Out transactions are not
correctly processed into the memory.

3- 9

Downloaded from www.Manualslib.com manuals search engine

 4. SYSTEM START-UP PROCEDURE EO3-11106

4. SYSTEM START-UP PROCEDURE

4. SYSTEM START-UP PROCEDURE

Case 1: To start-up using the MA-600 terminal only

RAM Clear (Chapter 5)

All the programming operations required

for the terminal (Chapter 6)

Case 2: To start-up by installing programming data from the PC

CAUTION!
< Precautions for connection to PC >
1. The USB cable should be connected to the ECR each time a PC sends/receives data to/from the ECR.
If the USB cable is kept connected to the ECR for a long period of time, data transfer may not be
performed properly.
2. When the ECR is connected to a PC with the USB cable, be sure to turn on the ECR in any mode other
than BLIND mode. Otherwise, the ECR may not start.

RAM Clear (Chapter 5)

PC Transmission Information Setting Perform this setting only for selecting

any other than the default value.
(See the next page.)

Turn off the ECR.

Connect a PC to the ECR via the USB

cable.

Turn on the ECR in any mode other than

BLIND mode.

DLL (Down Line Loading) the data For details, refer to the MA-600 Series
PC Programming Tool Manual.
programmed on the PC to the terminal.

4- 1

Downloaded from www.Manualslib.com manuals search engine

 4. SYSTEM START-UP PROCEDURE EO3-11106

4. SYSTEM START-UP PROCEDURE

PC Transmission Information Setting

Data transmission information setting with a PC connection is performed here.

CONDITION Any time outside a sale

OPERATION Mode Lock: BLIND

68 [X] 1 [ST] | POL Watch Timer | [#]

Max. 2 digits: 0 to 99
(Standard: 20 sec.)

2 [ST] | Response Watch Timer | [#]

Max. 2 digits: 0 to 99
(Standard: 20 sec.)

3 [ST] | Transmission Delay Timer | [#]

Max. 2 digits: 0 to 99
(1 = 20 ms)
(Standard: 3 = 60 ms)

4 [ST] | Transmission Delay Timer 2 | [#]

2 digits: 15 to 99
(1 = 20 ms)
(Standard: 25 = 500 ms)

[AT/TL]

NOTE: When performing the key operation of 68 [X] [AT/TL], a receipt containing the currently programmed
values is issued.

Example) To set the following values;

• POL Watch Timer: 30 (sec) TEC STORE
• Response Watch Timer: 20 (sec) 1343 PEACH DRIVE
PHONE: 87-6437
• Transmission Delay Timer: 4 (80 ms)
• Transmission Delay Timer 2: 25 (500 ms) Open 8:00am to 7:00pm
Closed: every Wednesday

Key Operation: Mode Lock: BLIND, enter 68, depress [X].

31-10-2005 MON #3001
1 [ST] 30 [#] POL Watch Timer
2 [ST] 20 [#] Response Watch Timer PC COM.
#1 30
3 [ST] 4 [#] Transmission Delay Timer #2 20
4 [ST] 25 [#] Transmission Delay Timer 2 #3 4
#4 25
[AT/TL] To complete this setting
0077 16:50TM

4- 2

Downloaded from www.Manualslib.com manuals search engine

 5. RAM CLEAR, DATA CLEAR, STATUS CLEAR EO3-11106

5.1 RAM Clear

5. RAM CLEAR, DATA CLEAR, STATUS CLEAR

5.1 RAM Clear
CAUTION!
This clear operation deletes all programmed data and sales data stored in the memory of the
ECR. (i.e., the ECR goes back to initial status.)
If the ECR becomes completely inoperative due to battery discharge or malfunction of the program memory, the
RAM Clear operation must be carried out. When the RAM Clear is operated, all memory stored in the RAM will
be cleared. (i.e., the programmed data and the sales data) In the clearing process, the designated zero-amount
format is reset. Also “Initial Data” and “Initial Status” for respective programming items are automatically reset. A
RAM clear is also necessary to determine the type of the ECR keyboard.

1. Unplug the ECR to turn OFF.

2. Use the S key to turn the Mode Lock to “BLIND” position.

3. Plug in the ECR to turn ON, causing the following message is displayed.
Please push [AT/TL]
or please perform a
RAM-C / DATA-C

4. Depress the following Numeric keys according to the zero-suppress form and the type of keyboard installed.
Keyboard Type Zero-suppress
Numeric Keys
(Destination Code) Form
[1] & [8] Flat Type (IT) .--0
[1] & [9] Ordinary Type (IT) .--0
[3] & [8] Flat Type (QP) 0.00
[3] & [9] Ordinary Type (QP) 0.00

5. Depress the [AT/TL] key.

6. A RAM Clear receipt is issued.

31-10-2005 MON #0

RAM-C

0001 13:43TM

NOTES: 1. When the RAM clear operation is performed, the condition “after all sales data reset” is obtained,
just as “Status Clear” and “Data Clear”. Therefore, no Reset Report should be taken for starting
any programming operation.
2. On completion of Step 6, all the memory will be cleared, and at the same time the keyboard will
automatically be programmed as specified in the “Standard Keyboard” (refer to the “SFKC”
programming operation later described).
3. After a RAM Clear, the Standard Program Data for FINANCIAL REPORT ITEM NAME and PRINT
LINE ITEM NAME, etc. will also be set automatically.

5- 1

Downloaded from www.Manualslib.com manuals search engine

 5. RAM CLEAR, DATA CLEAR, STATUS CLEAR EO3-11106

5.2 DATA Clear

5.2 DATA Clear

CAUTION!
This clear operation deletes all sales data of any operation sequence stored in the memory of the
ECR.
Performing the DATA Clear operation will clear only the sales data accumulated in the memory of the ECR
(report memory), however, the programmed data will not be cleared. By this operation, all sales data including
non-resettable totals and counters, Reset Report Counts, and Receipt Consecutive No. are cleared.

1. Unplug the ECR to turn OFF.

2. Use the S key to turn the Mode Lock to “BLIND” position.

3. Plug in the ECR to turn ON, causing the following message is displayed.
Please push [AT/TL]
or please perform a
RAM-C / DATA-C

4. Depress the following Numeric key.

Zero-suppress
Numeric Key Destination Code
Form
[1] IT .--0
[3] QP 0.00

5. Depress the [AT/TL] key.

6. A DATA Clear receipt is issued.

31-10-2005 MON #0

DATA-C

0001 13:44TM

NOTES: 1. When the DATA clear operation is performed, the condition “after all sales data reset” is obtained,
just as “Status Clear”. Therefore, no Reset Report should be taken for starting any programming
operation.
2. None of PLU table, stock status, and stock memory are cleared.

5- 2

Downloaded from www.Manualslib.com manuals search engine

 5. RAM CLEAR, DATA CLEAR, STATUS CLEAR EO3-11106

5.3 STATUS Clear

5.3 STATUS Clear

Performing the STATUS Clear operation will clear an error and the key locked condition, however, the sales data
and the programmed data will not be cleared by this operation. When the STATUS Clear is operated to clear a
key locked condition during sale, the sale item data that has already been entered for the current sale will be
cleared.

The STATUS Clear operation obtains the condition “after all sales data reset” which is required for some
programming operations, but this operation will not affect any sales data. This condition is obtained by taking
reset reports. In case you do not want to reset the sales data such as in business hours, this function is effective.
Depending on the programming item, sales data should be reset instead of STATUS Clear to keep consistency
between programmed data and sales data.

The STATUS Clear can be performed in 2 methods shown below.

< Method 1 >

1. Unplug the ECR to turn OFF.

2. Use the S key to turn the Mode Lock to “BLIND” position.

3. Plug in the ECR to turn ON, causing the following message is displayed.
Please push [AT/TL]
or please perform a
RAM-C / DATA-C

4. Depress the [AT/TL] key.

5. A STATUS Clear receipt is issued.

< Method 2 >

1. Turn the Mode Lock to “SET” position.

2. Depress the [9] key (Numeric key) then the [ST] key.

3. A STATUS Clear receipt is issued.

31-10-2005 MON #0

STATUS-C

0002 13:45TM

5- 3

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6. TERMINAL FILE PROGRAMMING

6. TERMINAL FILE PROGRAMMING

Table of Terminal File Programming Operations
Condition Mode Lock
Operation Page
(NOTE) Position
Instructions for Programming --- --- 6-2
Character Entries --- --- 6-7
Condition Required for Programming Operations --- --- 6-13
SFKC (Selective Function Key Code) Programming All Resets BLIND 6-14
BLIND
System Option Programming FZ 6-18
SET
Commercial Message Programming Anytime SET 6-49
Footer Message Programming Anytime SET 6-52
Store Name Message Programming Anytime SET 6-55
Department Name Programming Anytime SET 6-59
Department Group Name Programming Anytime SET 6-61
Cashier Name and Status Programming Anytime/CZ SET 6-63
PLU Name Programming Anytime SET 6-66
Salesperson Name Programming Anytime SET 6-68
Financial Report Item Name Programming Anytime SET 6-71
Print Line Item Name Programming Anytime SET 6-77
Display Item Name Programming Anytime SET 6-83
Error Item Name Programming Anytime SET 6-87
Read/Reset Report Name Programming Anytime SET 6-93
Anytime/DZ, DGZ, PZ,
Department Table Programming SET 6-98
PGZ
Department Preset Price Setting or Changing Anytime SET 6-104
Department Listing Capacity (LC) Programming Anytime SET 6-106
Key Sticker Printing Anytime SET 6-109
PLU Table Programming Anytime/PZ SET 6-113
PLU Preset Price Setting or Changing Anytime SET 6-120
PLU Preset-Code Key Setting Anytime SET 6-123
%+ and %- Preset Rate Setting Anytime SET 6-128
VAT or Add-on Tax Rate Setting FZ SET 6-130
Foreign Currency Exchange Rate Setting Anytime SET 6-132
Negative Amount Key Limit Amount Setting Anytime SET 6-135
Time Setting or Adjustment Anytime SET 6-137
Date Setting or Adjustment Anytime SET 6-138
Store/Register No. Setting Anytime SET 6-140
Hourly Range Table Setting HZ SET 6-142
Tone Volume Setting Anytime SET 6-146
Report Item Print/Non-Print Setting Anytime SET 6-148
Key Status Programming Anytime SET 6-153
Cash Tender Key Preset Amount Setting Anytime SET 6-157
Drawer Warning Time Setting Anytime SET 6-159
Special Rounding Process Setting, 1-digit type Anytime SET 6-161
Special Rounding Process Setting, 2-digit type Anytime SET 6-163
Number of Receipt Print Buffer Line Setting Anytime SET 6-166
Serial No. Setting Anytime SET 6-168

NOTE: All Resets = All Daily and GT Resets DGZ = After Department GT Reset PGZ = After PLU GT Reset
Anytime = Any time outside a sale DZ = After Department Daily Reset PZ = After PLU Reset
(No condition required) FZ = After Financial Daily Reset
CZ = After Cashier Reset HZ = After Hourly Range Reset

6- 1

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.1 Instructions for Programming

6.1 Instructions for Programming

On the MA-600 series adopting the LCD display, each programming operation is performed by selecting the
corresponding menu item on the LCD display.
The keyboard layout is automatically switched among three according to operation to be performed (ordinary
registration, read/reset, programming) when the Mode Lock is turned to the corresponding position.
Accordingly, in addition to the character code entry method, the character entries in programming operations are
also performed directly through the ordinary type keyboard.

6.1.1 SET Mode Menu

When performing a programming operation, a desired programming item is selected from the menu which is
shown on the LCD display. Programming menu tree is as shown below.

1 MESSAGES 4 RATE, LIMIT AMOUNT

1 COMMERCIAL MESSAGE 1 %- RATE (%-/%+)
2 FOOTER MESSAGE 2 VAT/TAX RATE
3 STORE MESSAGE 3 CUR EXCHANGE RATE
4 DISC AMT LIMIT
2 NAMES
1 DP KEY NAME
2 DP GROUP NAME 5 BASIC
3 CASHIER NAME 1 TIME
4 PLU (ITM NO.) NAME 2 DATE
5 SALESPERSON NAME 3 REGISTER NO.
6 FINANCIAL ITM NAME 4 HOURLY RANGE
7 PRINT ITEM NAME 5 KEY-IN TONE
8 DISPLAY ITEM NAME
9 ERROR ITEM NAME 6 OTHER
0 X/Z REPORT NAME 1 REPORT PRINT ITEM
2 SYSTEM OPTION
3 DP/PLU 3 KEY FUNCTION
1 DP 4 CASH KEY AMOUNT
1 DP SETTING 5 DRW WARNING TIME
2 UNIT PRICE 6 ROUND TBL 1 DIGIT
3 DIGIT LIMIT (PRICE) 7 ROUND TBL 2 DIGIT
4 KEY STICKER PRINT 8 RTC PRINT BUFFER
9 SERIAL NO.
2 PLU
1 PLU SETTING
2 UNIT PRICE
3 ASSIGN TO KEYBOARD
4 DELETE (INDIV)
5 DELETE (ALL)

6- 2

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.1 Instructions for Programming

6.1.2 Keyboard Layout Variations

The keyboard layout is automatically switched among three according to operation to be performed (ordinary
registration, read/reset, programming) when the Mode Lock is turned to the corresponding position.
In this chapter, various programming operations are performed with the keyboard layout for programming.

(1) Keyboard layout for ordinary registration (It is programmed as default setting.)

Mode Lock Position: REG MGR

• Ordinary Type Keyboard

LOG/ VALI RECIPT SALES
RECEIPT DATE ISSUE RF JF CUR PERSON
1 6 11
RTN ALL
MDSE VOID
C # R/A PO
2 7 12
ITEM
NS CORR
7 8 9 %-
3 8 13
PR
OPEN
X 4 5 6 VAT MISC
4 9 14
LC
OPEN
AMT 1 2 3 CRT CPN
5 10 15
CHK
PLU 0 00 . ST AT/TL
TEND

• Flat Type Keyboard

LOG/ RECEIPT
RECEIPT ISSUE RF JF R/A PO
1 8
ITEM RTN ALL
CORR
VOID MDSE VOID %-
2 9

# C NS VAT CUR
3 10

AMT 5 8 9 CRT
4 11
CHECK
X 4 5 6
5 12 TEND

1 2 3 ST
6 13
PLU
0 00 . AT/TL
7 14

PLU Preset-code keys Department

keys

6- 3

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.1 Instructions for Programming

(2) Keyboard layout for programming

Mode Lock Position: SET BLIND

• Ordinary Type Keyboard

↑ Del History RF JF A F K P U

ALL
↓ C # B G L Q V
VOID

← Rtn 7 8 9 C H M R W

→ Dbl 4 5 6 D I N S X

Enter A/a 1 2 3 E J O T Y

PLU 0 00 . ? End Z

• Flat Type Keyboard

1 2 3 4 5 6 7 8 9 0 LOG RF JF ↑ ↓

ALL
! @ # $ % & * ( ) : A/a Dbl Del VOID ← →

β Σ ú á é ê â è ç Œ # C History Rtn Enter

Ä Ö Ü Å Æ Ñ £ Ø + - ? 7 8 9

Q W E R T Y U I O P X 4 5 6

? A S D F G H J K L 1 2 3 ST
PLU
SP Z X C V B N M , 0 00 . End

6- 4

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.1 Instructions for Programming

(3) Keyboard layout for Read/Reset

Mode Lock Position: X Z

• Ordinary Type Keyboard

↑ RF JF

↓ C #

← Rtn 7 8 9

→ X 4 5 6

Enter 1 2 3

PLU 0 00 . ST AT/TL

• Flat Type Keyboard

RF JF ↑ ↓

← →

# C Rtn Enter

7 8 9

X 4 5 6

1 2 3 ST
PLU
0 00 . AT/TL

6- 5

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.1 Instructions for Programming

6.1.2 Basic Key Functions

1. The following are main keys and their functions to be used in programming operations.
(1) Keys for selecting items on the menu screen
Key Function
[↑] This key is used for moving the cursor upward.
[↓] This key is used for moving the cursor downward.
[←] This key is used for moving the cursor leftward.
[→] This key is used for moving the cursor rightward.
[Enter] This key is used for selecting a desired item after moving the cursor.
[Rtn] This key is used for returning the display to the previous screen.
[?] While ? is shown on the upper-right corner of the LCD display screen, the [?] key
depression results in that a guidance message corresponding to the current operation
appears on the LCD display. When depressing the [?] key again, the display will
return to the previous screen.

(2) Keys for character entries

Key Function
[→] This key is used for entering a one-byte space.
[C] This key is used for deleting all the entered characters together.
[Dbl] This key is used for switching character mode between “one-byte character” and “two-
byte character” alternately.
[A/a] This key is used for switching between “capital letter” and “small letter” alternately.
The key is effective when entering characters A to Z through the programming
keyboard or PK-2 keyboard (hardware option).
[Del] This key is used for deleting a character.
[#] In the character code entry method, entering a character code then depressing this
key results in that the corresponding character is entered.
[History] This key is used for performing character entries with the name previously entered.

(3) Keys for programming

Key Function
[←] This key is used for selecting a desired item.
[→] This key is used for selecting a desired item.
[C] This key is used for cancelling an operation just performed.
[Enter] This key is used for entering a desired item.
[Rtn] This key is used for returning the display to the previous screen.
[?] While ? is shown on the upper-right corner of the LCD display screen, the [?] key
depression results in that a guidance message corresponding to the current operation
appears on the LCD display. When depressing the [?] key again, the display will
return to the previous screen.
[End] This key is used for ending the current programming operation.
[PLU] This key is used for the PLU programming.

2. Functions of the [C] key

• When an entered program data is already printed, the [C] key cannot clear if any longer. To correct the
data, re-enter it.
• Before the entered data is printed, the data may be cleared by the [C] key (except in the SFKC
Programming Operation).

6- 6

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.2 Character Entries

3. To clarify the operation flow, definitions of keys of the ECR keyboard are as shown below.
| | --------- Selective numeric value which is entered through the Numeric keys.
[ ]---------- Depression of the function key.
xxxx------------- Fixed numeric value which is entered through the Numeric keys.
Fixed

4. Table of key names in SET and REG modes

The keyboard layout for programming is adopted in SET mode.
The following table shows key names in SET mode and corresponding ones in REG mode.
Key name in REG mode Key name in REG mode
Key name in SET mode
(Normal type keyboard) (Flat type keyboard)
[↑] [LOG/RECIEPT] [R/A]
[↓] [RTN MDSE] [PO]
[←] [NS] [%-]
[→] [PR OPEN] [ - ]
[Enter] [LC OPEN] [CUR]
[Rtn] [ITEM CORR] [VAT]
[?] [ST] [AMT]
[C] [C] [C]
[Dbl] [X] [VOID]
[A/a] [AMT] [ITEM CORR]
[Del] [VALI DATE] [RTN MDSE]
[#] [#] [#]
[History] [RECEIPT ISSUE] [NS]
[End] [AT/TL] [AT/TL]
[PLU] [PLU] [PLU]

6.2 Character Entries

There are two methods of character settings for various names and messages:
CHARACTER CODE ENTRY Method and DIRECT CHARACTER ENTRY Method.

CHARACTER CODE ENTRY Method

This method is to set a character by entering a Character Code and depressing the [#] key. The method is
operated only on the ECR keyboard (Ordinary Type or Flat Type).

DIRECT CHARACTER ENTRY Method

This method is to set a character by directly depressing the Character Keys on any of the following keyboard:
• ECR keyboard with the keyboard layout for programming
• PK-2 keyboard (PLU keyboard; hardware option)

By using those character keys, the characters are directly entered. In this manual, sample operations are
attached to most of the programming operations. And at name or message programming portions, characters
except for numeric and special symbols are entered by the DIRECT CHARACTER ENTRY method.

On the following pages, Character Code Tables under the CHARACTER CODE ENTRY Method and two
different keyboards under the DIRECT CHARACTER ENTRY Method are shown. These pages are to be
referred to, every time the “Character Entries” sequence is contained in various programming operations in
this manual.

Read through these pages at least once first, so that you may know the appropriate method of character
entries using the ECR keyboard and/or option keyboard.

6- 7

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.2 Character Entries

6.2.1 Character Code Entry Method

Character Code Table 1: Standard Characters

Column Code

2 3 4 5 6 7 8 9 10 11 12 13 14 15

00 SP 0 @ P ` p € „ á Å \ →

Row 01 ! 1 A Q a q é å ←
Code
02 " 2 B R b r ⎡ í Ø ↓

03 # 3 C S c s ⎦ ó ø ↑

04 $ 4 D T d t , ú Æ ½

05 % 5 E U e u • â æ ¼

06 & 6 F V f v Ä ê Œ Ì

07 ' 7 G W g w Ë î œ ‘

08 ( 8 H X h x Ö ô β Kg

09 ) 9 I Y i y Ü û ¢ lb

10 * : J Z j z É à £ No

11 + ; K [ k { ä è Φ X

12 , < L ¥ l | ë ì ∑ V

13 - = M ] m } ï ç ÷ U

14 . > N ^ n ¯ ö Ñ ─

15 / ? O _ o ü ñ

NOTE: Characters of those character codes 1007, 1206, 1207, 1211, 1500 through 1503, and 1506 through
1514 cannot be printed on the slip printer.

6- 8

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.2 Character Entries

Character Setting Operations

• To set a one-byte character, enter the COL (column) code and then the ROW code, followed by the [#] key.
ex.) To set “%”, enter 205 and depress the [#] key.
To set “kg”, enter1508 and depress the [#] key.

• To set a space instead of a character, simply depress the [#] key without a prior entry, or enter 200 and
depress the [#] key.

• To set two-byte characters, depress the [Dbl] key to declare the two-byte character entry, then enter a
character code, followed by the [#] key. The [Dbl] key declaration is effective until this key is depressed again.
ex.) To set “GROUP” all in two-byte characters:
[Dbl] 407 [#] 502 [#] 415 [#] 505 [#] 500 [#]
G R O U P

Two-byte character declaration

ex.) To set “GROUP”, “G” in two bytes, and “ROUP” in one byte:
[Dbl] 407 [#] [Dbl] 502 [#] 415 [#] 505 [#] 500 [#]
G R O U P

Two-byte character Cancelling

Declaration the declaration

6- 9

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.2 Character Entries

6.2.2 Direct Character Entry Method

Using Keyboard (installed as the ECR Main Keyboard):

-- Keyboard layout for programming --

• Ordinary Type Keyboard

↑ Del History RF JF A F K P U

ALL
↓ C # B G L Q V
VOID

← Rtn 7 8 9 C H M R W

→ Dbl 4 5 6 D I N S X

Enter A/a 1 2 3 E J O T Y

PLU 0 00 . ? End Z

• Flat Type Keyboard

1 2 3 4 5 6 7 8 9 0 LOG RF JF ↑ ↓
! @ # $ % & * ( ) : A/a Dbl Del ? ← →
β Σ ú á é ê â è ç Œ # C History Rtn Enter

Ä Ö Ü Å Æ Ñ £ Ø + - 7 8 9
Q W E R T Y U I O P X 4 5 6
? A S D F G H J K L 1 2 3 ST
PLU
SP Z X C V B N M , 0 00 . End

Character keys in programming Function keys in programming

Character Keys: Simply depress the key to enter the character. (The [#] key should not follow.)
Keys 1 to 0 are used for entering numeric characters 1 to 0.

Function Keys: These are function keys to be used in programming operations.

The numeric keys here are used for entering PLU Codes, etc. and numeric values as program
data.

6- 10

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.2 Character Entries

Using PK-2 (PLU Keyboard; hardware option)

The PK-2 keyboard is used for entering a required PLU code by simply depressing the code-preset key on this
keyboard in REG or MGR mode. In addition, the PK-2 can be used for directly entering characters during the
programming operations that require character settings such as STORE NAME/MESSAGE AND COMMERCIAL
MESSAGE PROGRAMMING and DEPARTMENT NAME PROGRAMMING.

The following shows the key indications of the PK-2 for the character setting purpose.
Insert the template for this purpose between the film layers that cover the PK-2.

Instead of entering a 3- or 4-digit character code and depressing the [#] key on the ECR keyboard, a simple
depression of the appropriate key on the PK-2 will be the character entry.

All the function keys such as [↑], [↓], [→], [←], [Enter] must be operated on the ECR side. Any characters not
listed on the template may be entered by the CHARACTER CODE ENTRY method on the ECR keyboard. (The
characters even listed on the template may be entered as well by that method.)

The two-byte character declaration is the same as in the CHARACTER CODE ENTRY method.

7 8 9

4 5 6

1 2 3

! @ # $ % ¢ & * ( ) 0

q w e r t y u i o p ~ ^

a s d f g h j k l " _ +

z x c v b n m ' - =

Q W E R T Y U I O P [ ]

A S D F G H J K L ; : ,

Z X C V B N M Space . / ?

6- 11

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.2 Character Entries

6.2.3 How to use the [History] key

The [History] key is used for performing character entries with the name previously entered.

Operation:
[History] ([↓]) [Enter]

1) The [History] key depression will let the most recently programmed name displayed on the LCD display.
2) The [↓] key depression will let the second most recently programmed name displayed. (Up to 10
programmed names will be displayed in reverse chronological order.)
3) The [Enter] key depression will allow the name on the LCD display to be entered.

Example of operation:
When “A LUNCH” for PLU1 and “B LUNCH” for PLU2 are programmed in the PLU name programming.
Key operation Description LCD display
1 [PLU] PLU No.1 setting is declared. PLU0001
[C] The default setting displayed on the LCD display is deleted.
401 [#] The character A is entered. A
[#] A space is entered. A
412 [#] The character L is entered. A L
505 [#] The character U is entered. A LU
414 [#] The character N is entered. A LUN
403 [#] The character C is entered. A LUNC
408 [#] The character H is entered. A LUNCH
[ST] The name of PLU No.1 is entered.
2 [PLU] PLU No.2 setting is declared. PLU0002
[C] The default setting displayed on the LCD display is deleted.
[History] The name of PLU No. 1 just entered is called. A LUNCH
[Enter] The name of PLU No. 1 is entered. A LUNCH
[Del] The character A of “A LUNCH” is deleted. LUNCH
402 [#] The character B is entered instead of the deleted A. B LUNCH
[ST] The name of PLU No.2 is entered.

6- 12

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.3 Condition Required for Programming Operations

6.3 Condition Required for Programming Operations

“CONDITION” is given at the top of each programming operation. The ECR must satisfy this condition to perform
programming operations.

There are two types of conditions:

“Any time outside a sale”

It means that the programming operation is allowed when a sale is finalized before going into any other sale entry.

“After------ reset”
It means that the designated reset report must be taken before entering the programming operation.
And an error will result if the operation is attempted without taking the report. However, the words “After ...
Reset” do not necessarily mean “immediately after ...”.

When the designated reset report has already been taken and then some operations are performed in the SET, X,
or Z mode, the condition “After ... Reset” is still satisfied and the programming operation is still allowed.

On the contrary, when the designated reset report has been taken but then some sales data relating to that
report’s output data are entered in the REG, MGR, or - mode, the programming operation will no longer be
allowed and the same reset report must be taken.

Thus the condition “After ... Reset” indicates that all the sales data relating to the report data must be zero
(except non-resettable memory data). Because of this “CONDITION” requirement, the report data will be
protected from any inconsistencies of sales data entered in the period from a resetting of the report to another
resetting of the same report next time.

6- 13

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.4 SFKC (Selective Function Key Code) Programming

6.4 SFKC (Selective Function Key Code) Programming

SFKC Programming is to determine the keyboard layout with the required keys. This operation must be
performed first before any other programming operation. If the RAM Clear is performed prior to the SFKC
programming, program only the keys that require changes from the SFKC in the Standard Keyboard which has
been set by the RAM Clear operation automatically. (For the Standard Keyboard, see Page 6-17.)

The following keys that are minimum requirements for programming and registering operations must be assigned
to the keyboard no matter what any other keys may or may not be assigned:
[C], [X], [ST], [AT/TL], [#], and Department Keys or [DP#]

CONDITION After all Z and GTZ reports, or after RAM Clear, DATA Clear, or STATUS Clear

OPERATION Mode Lock: BLIND

76 [AT/TL] | SFKC | [KEY] [AT/TL]

to read preset SFKC

The key that requires the
function of the SFKC

Repeat

1. Enter 76, and depress the key to be [AT/TL] (Cash Media key). This declares the SFKC Programming Start
and at the same time sets the SFKC 76 on the key.
From this step on, the depressed key will be [AT/TL].

2. Enter the SFKC (see the SFKC table on the following pages), and depress the key that requires the key name
of the SFKC. Repeat this step until all the necessary keys are set with their own SFKC’s. Each key on the
keyboard must correspond to one SFKC, except for SFKC 96 (PLU Preset-code Keys). If in this step, a key is
simply depressed without a prior SFKC entry, the SFKC that has been pre-programmed on that key is
displayed at that Amount portion.

3. Depress the [AT/TL] key (the key set as [AT/TL] in Step 1) to end the SFKC programming operation. The
display now shows “0” at the Amount portion. A receipt is issued.

NOTES:
1. The entered SFKC is displayed at the Amount portion of the display.
2. If a wrong code has been entered and the key has also been depressed (i.e. a wrong SFKC has been set on
a key), enter the correct SFKC and depress the key.
3. If “0” is entered as SFKC, the key will be dead and its memory will also be closed.
76 [AT/TL] 0 [KEY] [AT/TL]
4. Each of the keys programmed in this step will have its memory (if any) opened automatically.
5. The [C] key, if once set with SFKC 95, may be used to clear an error, but not to clear and SFKC entry. If
any SFKC is entered and the [C] key is depressed, that SFKC will be set on the key that was once the [C]
key.
6. To designate the SFKC 100, operate the keys [1] → [0] → [0]. In this case, the [00] key is unavailable.
7. When a key is opened here, the print status should be set to its memory in Report Item Print/Non-Print
Setting.
8. The [RF], [JF], [00], and [ . ] keys can also be programmed by the SFKC programming operation.
9. If [RF] and [JF] are programmed on several keys, that with largest key location code is effective. The
remaining [RF] and [JF] keys are ignored. (Only one them are operable each.)
10. The location of the [AT/TL] key is fixed.

6-14

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106
(Revision Date: Mar. 14, 2006)
6.4 SFKC (Selective Function Key Code) Programming

SFKC Table

SFKC Key Name Memory to be opened (REMARKS)

0 Dead-key code (used to close the key and memory)
1 to 40 Department Preset-code Keys 1 to 40 Respective Department memory
41 to 60 -- vacant --
61 RF (Receipt Feed) No memory
62 JF (Journal Feed) No memory
63 00 (Double-zero) No memory
64 000 (Triple-zero) No memory
65 • (Decimal Point) No Memory
66 VND CPN (Vender Coupon) Vender Coupon
67 STR CPN (Store Coupon) Store Coupon
68 -- vacant --
69 - (Amount Discount) Amount Discount
70 %+ (% I) %I
71 %- (% II) % II
72 RTN MDSE (Returned Merchandise) Returned Merchandise
73 ITEM CORR (Item Correct) Item Correct, Misc. Void
74 VOID (Void) Void, Misc. Void
75 ALL VOID (All Void) All Void
AT/TL (Cash Amount Tender/Total) Cash Sales, Cash-in-drawer,
76
-- Cash Media Cash-in-drawer Difference
Check Sales, Check-in-drawer,
77 CHK TND (Check Tender)
Check-in-drawer Difference
Credit Sales, Credit-in-drawer,
78 CRT (Credit Total)
Credit-in-drawer Difference
Misc. Sales, Misc.-in-drawer,
79 MISC TEND (Miscellaneous Tender)
Misc.-in-drawer Difference
Media-Coupon Sales, Media-Coupon-in-drawer
80 CPN (Media Coupon)
Media-Coupon-in-drawer Difference
Credit 1 Sales, Credit 1-in-drawer
81 CREDIT 1 (Credit 1)
Credit 1-in-drawer Difference
82 ST (Subtotal) No memory
83 R/A (Received-on-Account) Received-on-Account
84 PO (Paid-Out) Paid Out
85 NS (No-sale) No-sale Counter
86 PR OPEN (Preset Open) No memory
87 LC OPEN (Listing Capacity Open) No memory
88 OPEN (PR/LC Open) No memory
89 VALIDATE (Validation) Validation counter
90 # (Non-add Number) No memory
91 CONSIGNMENT Consignment counter
(To open memory, each PLU program is further
92 PLU (Price-Look-Up) necessary; however, if this key is closed, the
memory for all PLUs are closed.)
93 X No memory
94 RECEIPT ISSUE (Receipt Post-Issue) No memory
95 C (Clear) Clear Key Counter
96 PLU Preset-code keys No memory
97 TX1/M (Tax 1 Modifier) No memory
98 TX2/M (Tax 2 Modifier) No memory
99 -- vacant --
100 -- vacant --
101 EX (Tax Exempt) Exempt Customer, Exempt 1, 2, 3, 4
PB+ (Previous Balance +; for Manual Transfer, Previous Balance Sales, Previous
102
PB Entry Type) Balance R/A, Previous Balance PO
-- Continued on the next page –

6-15

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106
(Revision Date: Mar. 14, 2006)
6.4 SFKC (Selective Function Key Code) Programming

SFKC Table (continued)

SFKC Key Name Memory to be opened (REMARKS)

PB- (Previous Balance -; for Manual
103 No memory
PB Entry Type)
104 TRF (Transfer) No memory
105 to 107 -- vacant --
108 AMT (Amount) No memory
109 RPT (Repeat) No memory
110 to 115 -- vacant --
116 TX3/M (Tax 3 Modifier) No memory
117 to 120 -- vacant --
121 CUR 1 (Foreign Currency 1) Foreign Currency 1-in-drawer
122 CUR 2 (Foreign Currency 2) Foreign Currency 2-in-drawer
123 CUR 3 (Foreign Currency 3) Foreign Currency 3-in-drawer
124 CUR 4 (Foreign Currency 4) Foreign Currency 4-in-drawer
125 CUR 5 (Foreign Currency 5) Foreign Currency 5-in-drawer
Credit 2 Sales, Credit 2-in-drawer
126 CREDIT 2 (Credit 2)
Credit 2-in-drawer Difference
Credit 3 Sales, Credit 3-in-drawer
127 CREDIT 3 (Credit 3)
Credit 3-in-drawer Difference
Credit 4 Sales, Credit 4-in-drawer
128 CREDIT 4 (Credit 4)
Credit 4-in-drawer Difference
Credit 5 Sales, Credit 5-in-drawer
129 CREDIT 5 (Credit 5)
Credit 5-in-drawer Difference
130 LOG/RECEIPT (Log/Receipt) No memory
131 LOG (Log) No memory
132 SALES PERSON (Salesperson) No memory
133 -- vacant --
134 TX4/M (Tax 4 Modifier) No memory
135 DP# (Department No.) No memory
136 to 138 -- vacant --
139 RECEIPT (Receipt) No memory
140 to 142 -- vacant --
143 to 150 CLK1 (Cashier 1) to CLK8 (Cashier 8) No memory
151 to 162 -- vacant --
163 VAT (VAT Print) No memory
164 -- vacant --
165 -- vacant --
166 JP (Journal Print) No memory
167 -- vacant --
168 1st PRICE No memory
169 2nd PRICE No memory
170 3rd PRICE No memory
171 to 200 -- vacant --
201 VAT DISPLAY No memory
202 TX5/M (Tax 5 Modifier) No memory
203 TX6/M (Tax 6 Modifier) No memory
204 TX7/M (Tax 7 Modifier) No memory
205 TX8/M (Tax 8 Modifier) No memory
206 CASH1 No memory
207 CASH2 No memory
208 CASH3 No memory

6-16

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.4 SFKC (Selective Function Key Code) Programming

SFKC Receipt Sample

31-10-2005 MON #0

SFKC
#054 076 → 076
#043 102 → 102
#044 103 → 103
#045 104 → 104
#047 066 → 066
#046 067 → 067

0003 13:05TM

Standard Keyboard (auto-set by RAM Clear)

• Ordinary Type Keyboard

LOG/ VALI RECEIPT
SALES
RECEIPT DATE ISSUE RF JF CUR
↑ Del History 1 6 11 PERSON
RTN
ALL
MDSE
VOID C # R/A PO
↓ 2 7 12

NS ITEM 3
CORR 7 8 9 %- -
← Rtn 8 13
PR
OPEN X 4 5 6 VAT MISC
→ Dbl 4 9 14
LC
OPEN AMT 1 2 3 CRT CPN
Enter A/a 5 10 15

PLU 0 00 . ST AT/TL CHK

? End TEND

• Flat Type Keyboard

LOG/ RECIPT
RECEIPT ISSUE RF JF R/A PO
1 8
ITEM RTN ALL
VOID %-
CORR MDSE VOID
2 9

# C NS VAT CUR
3 10

AMT 7 8 9 CRT
4 11
CHECK
X 4 5 6
TEND
5 12

1 2 3 ST
6 13
PLU
0 00 . AT/TL
7 14

PLU Preset-code keys Department keys

6-17

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

6.5 System Option Programming

This operation is used to set the ECR’s basic features and selective functions to meet the requirement of the
market and your user.
This programming operation is performed in SET mode or BLIND mode.
In SET mode, you can select a desired menu item on the LCD display. Address No. 1 to Address No. 29 are
programmable. In BLIND mode, you can directly enter a desired Address No. on the keyboard. All system
options from Address No. 1 to Address No. 49 are programmable.

CONDITION After Financial Daily Reset

OPERATION For Dealer System Options: Mode Lock: SET

(Address No. 1 to No. 29)

For Dealer System Options: Mode Lock: BLIND

(Address No. 1 to No. 49)

Programming in SET mode

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] five times then [Enter].

or “6 OTHER” is selected.
Depress [6].

Depress [↓] then [Enter].

or “2 SYSTEM OPTION” is selected.
Depress [2].

Select a desired Address No.

(Selectable from Address No. 1 to Address No.29.)
with the [↑] or [↓] key.

The Bit Numbers currently programmed are displayed on the 7-

[Enter] segment Numeric display.

Move the cursor on to a desired bit No.

with the [↓] key.

Choose bit status with the [←] or [→] Every time the [←] or [→] key is depressed, N and Y are displayed
alternately. N and Y indicate RESET and SET statuses,
key. respectively.

The selected Address No. setting is entered.

[Enter] The Bit Numbers with SET status are displayed on the 7-segment
Numeric display.

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

6-18

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

Setting Example)
To set Address No. 1 with the following requirements:
(Refer to the Address No. 1 table on the subsequent page.)
Bit No. 1: Time NON-PRINT (SET status)
Bit No. 3: Subtotal NON-PRINT (SET status)
Other bits will be selected to “RESET” status.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “6 OTHER”.
and in SET mode, depress the [↓] key
five times.

Depress the [6] or [Enter] key.

Depress the [↓] key. The cursor is moved on to “2 SYSTEM

OPTION”.

Depress the [2] or [Enter] key.

Address No. list is displayed. Select a While ? is shown on the upper-right corner
of the LCD display screen, the [?] key
desired Address No. with the [↑] or [↓] depression results in that the following
key. guidance message appears on the LCD
display.
In this example, Address No. 1
(01NON-PRINT) is selected.

For the selected Address No., the Bit

Numbers currently programmed are
displayed on the 7-segment Numeric display.

With the [Enter] key depression, The [?] key depression results in that the
following guidance message appears on the
Address No. 1 setting is displayed. LCD display.

(continued on the next page)

6-19

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

(continued from the previous page)

Operation LCD Display Remarks

Depress the [→] key to select the The status of Bit No.1 is turned from N to Y.
N: RESET status
status of Bit No. 1. Y: SET status

The numeric value 1 indicating the Bit No.

with SET status is displayed on the 7-
segment Numeric display.

Depress the [↓] key twice to move the

cursor on to Bit No. 3 (B3ST).

Depress the [→] key to select the The status of Bit No.3 is turned from N to Y.
N: RESET status
status of Bit No. 3. Y: SET status

The numeric value 13 indicating the Bit Nos.

with SET status is displayed on the 7-
segment Numeric display.

The [Enter] key depression results in

that the Address No. 1 setting is
entered.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

Programming in BLIND mode

Repeat for another Address No.

18 [X] | Address No. | [ST] | Bit Nos for “SET” | [#] [AT/TL]

Enter a maximum of eight-digit number composed of Bit Nos

whose status must be selected to SET status in the Address.

ex.) To set Bit No. 2 only ...................... Enter 2.

To set Bits No. 2 and No. 3 ........... Enter 23.
To set all the Bit Nos ..................... Enter 12345678.
To reset all the Bit Nos .................. Enter 0.

NOTES:
1. Any Bit No. with the “-- vacant --” item will be ignored even if it is set.
(However, even if set, it will not result in an error.)
2. When a RAM Clear is completed, the status of each Bit No. is automatically set to the side marked with an
asterisk in the STANDARD STATUS column of each SYSTEM OPTION TABLE shown on the following
pages. Therefore, only the Bit status changes of the required Addresses may be entered according to your
customer’s requirements.

6-20

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

Setting Example)
To set Address No. 1 with the following requirements:
(Refer to the Address No. 1 table on the next page.)
Bit No. 1: Time NON-PRINT (SET status)
Bit No. 3: Subtotal NON-PRINT (SET status)
Other bits will be selected to “RESET” status.

Key Operation: Mode Lock: BLIND, enter 18, depress [X].

1 [ST] Address No. 31-10-2005 MON #0

13 [#] Bit Nos. for SET SYSTEM OP

[AT/TL] To complete this setting. #01---------------------------13

0003

6-21

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
1 NON-PRINT OPTION I

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

Time (on Sale Receipt, RESET PRINT *

1 Report, Program
Receipt) SET NON-PRINT

Sale Item Count on

RESET PRINT *
2 each Sale Receipt
SET NON-PRINT

Subtotal Amount print RESET PRINT *

3 by [ST] key on Receipt NOTE 1 below
and Journal SET NON-PRINT

RESET *
4 -- vacant --
SET

Customer Count for RESET PRINT *

5 each Department on
Department Reports SET NON-PRINT Both Bit 5 & 6 RESET:
Prints sales % of each
Sale % of each
Department and Group,
RESET PRINT * Department and Group
6
on Department and
SET NON-PRINT
Group Reports (NOTE 2)
“Department Gross
Gross Profit of each RESET PRINT * Profit Read Reports”
7 Department, on
Department Reports can be issued
SET NON-PRINT
regardless of this status
Sales Person on Sale RESET PRINT *
8 Receipt and Remote NOTE 3 below
Slip SET NON-PRINT

NOTE 1: This bit status selection is also applied to the following cases in which the subtotal amount is automatically printed.
• Sale Finalization, % Operation, Amount Discount, and Special Rounding Spec.

NOTE 2: • The sale % of a department = (That Department) / (Sum of Positive Department)

(When the “Sum of Positive Department” is zero or negative, the sale % of 0% will be printed.)
• The sale % of a negative Status Department is not printed.

NOTE 3: If SET, no printing is performed on the receipt printer and the Remote Slip Printer during the salesperson entry, however, it is
performed on the journal regardless of the setting.

6-22

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
2 NON-PRINT OPTION II

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

RESET *
1 -- vacant --
SET

RESET *
2 -- vacant --
SET

RESET *
3 -- vacant --
SET

RESET *
4 -- vacant --
SET

RESET *
5 -- vacant --
SET

INPS 1 for the Charge RESET PRINT ALL ITEMS * NOE 1 below
6 Posting on Remote Slip (INPS = Item Not Print
Printer SET INPS 1 on Slip)

INPS 2 for the Charge RESET PRINT ALL ITEMS *

7 Posting on Remote Slip NOTE 2 below
Printer SET INPS 2

RESET * This bit must always be

8 -- vacant --
RESET.
SET

NOTE 1: If SET, print items except the following will not be printed on the Remote Slip Printer in the charge posting operation.
PB+, PB-, Check Track No., CRT, PB R/A, PB PO and TRF

NOTE 2: If SET, print items except NEW BAL will not be printed on the Remote Slip Printer in the charge posting operation. Trailer Line
and NEW BAL will be printed on one line.

6-23

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
6
3 OPTIONAL FUNCTION I

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

Fraction Rounding
RESET Follow Bit 2 status * If both RESET, it will be
1 ROUND UP ROUND OFF.
SET ROUND UP
(If both SET, it will be
ROUND DOWN.)
Fraction Rounding
RESET ROUND OFF *
2 ROUND DOWN NOTE 1 below
SET ROUND DOWN

[ST] key before

RESET NOT COMPULSORY *
3 finalizing a sale
SET COMPULSORY

Credit Balance in REG

RESET PROHIBITED *
4 mode
NOTE 2 below
SET ALLOWED

Drawer Opening on
RESET OPEN *
5 taking Financial Reports
SET NOT OPEN

RESET UNIT PRICE x QUANTITY

Quantity Extension
6 (Multiplication) order
NOTE 3 below
SET QUANTITY x UNIT PRICE *
Manager Intervention
for entering Negative
RESET NOT REQUIRED *
7 NOTE 4 below
Departments/PLUs in
SET REQUIRED
REG mode
Manager Intervention
for finalizing Negative-
RESET NOT REQUIRED *
8 NOTE 5 below
balance Sales in REG
SET REQUIRED
mode

NOTE 1: The selective status of the fraction rounding here applies to quantity extension, %+, and %- calculations. The fraction resulted
from any tax % calculations (VAT or Add-on Type) will be ROUNDED OFF (no alternative rounding method is provided).

NOTE 2: The "Credit Balance" means that amount entries through [-] (Amount Discount), [VOID], [STR CPN], [VND CPN], will result in
over-subtraction of the subtotal amount at the time of the entry through any of those keys. If the SET status (ALLOWED) is
selected, over-subtraction using these keys will be allowed in the REG mode. The [RTN MDSE] key and negative
departments/PLUs are not subject to this "Credit Balance" status selection. The Credit Balance is always allowed in the MGR or
- mode.

NOTE 3: If RESET, Triple Multiplication operation is not possible. (Doing so may cause an error.)

NOTE 4: This optional function is effective in the negative department/PLU entry operation. This operation is possible in the MGR or
- mode regardless of the setting.

NOTE 5: This optional function is effective for finalizing a negative balance sale by the media keys (excepting the [AT/TL] key).
This operation is possible in the MGR or - mode regardless of the setting.

6-24

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
23
4 OPTIONAL FUNCTION II

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.
Zero-skip in All
Department and
RESET PRINT all Departments data * Departments/Groups
1 with no sale will be
Department Group skipped in the report.
SET ZERO-SKIP
Reports
RESET PRINT all PLUs data
Zero-skip in PLU
2 Reports
SET ZERO-SKIP *
RESET PRINT all items data
Zero-skip on Financial
3 and Cashier Reports
SET ZERO-SKIP *
RESET ACTIVE *
4 Cashier feature NOTE 1 below
SET NON-ACTIVE

Cashier No. Display on

RESET NOT DISPLAYED *
5 Operator Display
SET DISPLAYED (NOTE 2) When both SET or both
RESET, Department
PLU Price Level Display
RESET NOT DISPLAYED * No. will be displayed.
6 on Operator Display
SET DISPLAYED (NOTE 3)

RESET *
7 -- vacant --
SET

RESET *
8 -- vacant --
SET

NOTE 1: If SET, the cashier feature is not active as the registering operation is possible without cashier sign-ON.
• Cashier read and reset operations are not possible. Doing so may cause an error.
• Cashier signing operation (inputting 4-digit numeric values then [LOG]) in REG mode may cause an error.
• Cashier name is not printed on the validation slip.
• The cashier name portion on the receipt and the journal will be blank. Prior to changing this bit status from RESET to SET,
the cashier daily/GT reset should be performed to clear the cashier memory. If the bit status is changed without performing
the reset operation, the cashier memory data will not be guaranteed.

NOTE 2: If SET, the Cashier No. of the signed-ON cashier is always displayed on the Department Code position (2 digits). Even when a
department entry is performed, the Cashier No. is displayed instead of the department code.

NOTE 3: If SET, the PLU Price Level is always displayed on the second leftmost digit of the 7-segment Numeric display.

-- Address No. 5 is vacant. --

6-25

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
6 REMOTE SLIP PRINTER CONTROL

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

Remote Slip Print RESET NOT COMPULSORY *

1 Compulsory for any PB NOTE below
entry SET COMPULSORY

RESET *
2 -- vacant --
SET

RESET *
3 -- vacant --
SET

RESET *
4 -- vacant --
SET

RESET *
5 -- vacant --
SET

RESET *
6 -- vacant --
SET

RESET *
7 -- vacant --
SET

RESET *
8 -- vacant --
SET

NOTE: If SET, printing operation on the Remote Slip Printer is compulsory. In this case, a slip paper should be set prior to performing
any Previous Balance entry.

6-26

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
7 OPTIONAL FUNCTION III

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

RESET *
1 -- vacant --
SET

RESET *
2 -- vacant --
SET

RESET *
3 -- vacant --
SET

RESET *
4 -- vacant --
SET

RESET *
5 -- vacant --
SET

Cashier Sign ON/OFF

RESET PRINT and ISSUE *
6 Receipts
NOTE below
SET NOT ISSUE

Drawer Open by
RESET NOT OPEN *
7 Cashier Sign ON/OFF
SET OPEN

RESET *
8 -- vacant --
SET

NOTE: If SET, the cashier sign-ON/OFF receipt will not be issued. However, the printing operation is performed on the journal
regardless of the setting. When the automatic cashier sign-OFF function is active (i.e. the SET status is selected in Address No.
32, Bit No. 3), the cashier sign-OFF print is performed neither on the receipt nor on the journal regardless of the status of Address
No. 7, Bit No. 6.

-- Address Nos. 8 to 10 are vacant. --

6-27

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
568
11 NON-PRINT OPTION III

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

RESET *
1 -- vacant --
SET

RESET *
2 -- vacant --
SET

RESET *
3 -- vacant --
SET

RESET *
4 -- vacant --
SET

RESET COUNT
[C] (Clear) Key Counter
5 on Reports
SET NON-COUNT *
Financial and Cashier RESET PRINT
6 Daily Read Counter on NOTE 1 below
Reports SET NON-PRINT *
RESET *
7 -- vacant --
SET

RESET PRINT (NOTE 2 below)

[C] (Clear) Key on
8 Journal
SET NON-PRINT *
NOTE 1: If RESET, when performing a financial read/reset or cashier read/reset operation, their respective read counter (X counter) is
printed on the report. (For details, please refer to the Table below.) The read counter (X counter) increases by one regardless of
this bit status.
Table: X counter and Z counter print
Daily GT
X Counter Z Counter X Counter Z Counter
Daily Read Printed --- --- ---
Daily Reset Printed Printed --- ---
GT Read --- --- Printed ---
GT Reset --- --- Printed Printed

NOTE 2: The descriptor “CLEAR” (programmable) is printed on Journal every time the [C] key is operated in the REG mode to clear a
numeric value or declaration key error. However, it will not be printed when the [C] key is depressed to clear an error condition.
Additionally, this printing will not be recorded in the MGR or - mode. It will be performed neither on the Receipt nor Remote Slip
Printer in any mode.

- - Address Nos. 12 to 16 are vacant. - -

6-28

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
4
17 OPTIONAL FUNCTION IV

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

RESET *
1 -- vacant --
SET

RESET *
2 -- vacant --
SET

RESET *
3 -- vacant --
SET

RESET HOLD
4 Price Shift Function NOTE below
SET ONE-TIME *
RESET *
5 -- vacant --
SET

RESET *
6 -- vacant --
SET

RESET *
7 -- vacant --
SET

RESET *
8 -- vacant --
SET

SET: When the [2nd PRICE] or [3rd PRICE] key is pressed, second or third price level is active for the next PLU entry only.
Then first price level is automatically regained.
NOTE: RESET: When the [2nd PRICE] or [3rd PRICE] key is depressed, the second or third price level is held during a sale
transaction. After finalizing a sale, the first price level is automatically regained.
SET: When the [2nd PRICE] or [3rd PRICE] key is depressed, the second or third price level is active for the next PLU
entry only. Then the first price level is automatically regained.

- - Address No. 18 is vacant. - -

6-29

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
19 CONSIGNMENT OPTION

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

Single-Consignment or RESET SINGLE-CONSIGNMENT *

1 NOTE 1 below
Multi-Consignment
SET MULTI-CONSIGNMENT

RESET PRINT *
2 Date Print
SET NON-PRINT

Consecutive No. (of RESET PRINT *

3
Receipt) Print
SET NON-PRINT

RESET *
4 -- vacant --
SET

RESET PRINT *
5 Cashier Code Print
SET NON-PRINT

Logo, Store Message, RESET PRINT *

6 Commercial Message,
Footer Message Print SET NON-PRINT

Receipt feed after the RESET NO FEED *

7 trailer line print If both RESET, no receipt
(5-line feed) SET FIVE-LINE FEED feed is performed. (A long
receipt is issued.)
If both SET, a 10-line feed is
Receipt feed after the RESET NO FEED * performed.
8 trailer line print (NOTE 2 below)
(10-line feed) SET TEN-LINE FEED

NOTE 1: “SINGLE-CONSIGNMENT” means that consignment of the same item can be printed only once. (A second attempt to print the
same item will result in an error.)
“MULTI-CONSIGNMENT” means that consignment of the same item may be printed any number of times.

NOTE 2: The number of line feeds after printing a trailer line (cashier name, consecutive No., current time) is selected.
If only Bit No. 7 is SET, a five-line feed will be performed.
If both Bit No. 7 and No. 8 are SET, a ten-line feed will be performed.
If both are RESET, no line feed is performed.

6-30

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
20 TAX CONTROL I

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

Add-on Tax 1
RESET CLOSE *
1 Open/Close
SET OPEN

Add-on Tax 2
RESET CLOSE *
2 Open/Close
SET OPEN

Add-on Tax 3
RESET CLOSE *
3 Open/Close
SET OPEN

Add-on Tax 4
RESET CLOSE *
4 Open/Close
SET OPEN

Add-on Tax 5
RESET CLOSE *
5 Open/Close
SET OPEN

Add-on Tax 6
RESET CLOSE *
6 Open/Close
SET OPEN

Add-on Tax 7
RESET CLOSE *
7 Open/Close
SET OPEN

Add-on Tax 8
RESET CLOSE *
8 Open/Close
SET OPEN

NOTE: This optional function is effective when Address No. 21, Bit No. 5 has been SET (Add-on Tax feature).
When SET status is selected on the ECR adopting the Add-on Tax feature, Tax 1 through Tax 8 are open.
When Taxable status (SET status) is set to the [-], [%+], [%-], and [VND CPN] keys in the Key Status Programming, Tax 1
through Tax 8 are processed according to this bit status (Open/Close). VAT feature is not subject to this bit status.

6-31

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
21 TAX CONTROL II

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

Multiple Taxes Separate

RESET NON-PRINT *
1 Print on Receipt
SET SEPARATE PRINT
When Add-on Tax
Tax Total Amount on
RESET NON-PRINT * feature is selected at
2 Receipt Bit No. 5, taxes are
SET PRINT
always printed.

Taxable Total Print on

RESET NON-PRINT *
3 Receipt
NOTE 1 below
SET PRINT
This bit status selection
VAT Calculation Method
RESET (Price x Rate) ÷ (1 + Rate) * is effective only when
4 (VAT = ) VAT feature has been
SET (Price x Rate)
selected.

Tax Type:
RESET VAT *
5 VAT or Add-on Tax
NOTE 2 below
SET ADD-ON TAX
This bit status selection
NET VAT Total RESET NON-PRINT * is effective only when
6 Separate Print on
Receipt (NOTE 3) VAT feature has been
SET PRINT
selected.
RESET *
7 -- vacant --
SET
This bit status selection
NET Total Print on
RESET NON-PRINT * is effective only when
8 Receipt (NOTE 4) VAT feature has been
SET PRINT
selected.

NOTE 1: Whether the taxable total is printed on the receipt is selected.

SET: It is printed individually.
RESET: It is not printed.

NOTE 2: When the Add-on Tax feature is selected:

1) The [TX1/M] to [TX8/M] keys can reverse the respective Tax status of Departments and PLUs. Reversing the Tax status of
[% +], [% -], and [-] is also possible. (Neither the [TX1/M] to [TX7/M], nor [TX8/M] keys can be used when the VAT feature is
selected.)
2) When a taxable item (subject to any of Tax 1 to Tax 8) is entered in a sale, the symbol “T” is printed to the right of the item
amount.

NOTE 3: Whether the NET VAT total of each VAT is printed on the receipt is selected.
SET: It is printed.
RESET: It is not printed.

NOTE 4: Whether the NET total (amount total not including VAT total) is printed on the receipt is selected.
SET: It is printed.
RESET: It is not printed.

6-32

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
22 TAX CONTROL III

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

RESET NON-PRINT *
1 VAT Symbol Print NOTE 1 below
SET PRINT

Print order of VAT TL

RESET NET TL → VAT TL *
2 and NET TL
NOTE 2 below
SET VAT TL → NET TL

Single line spacing

RESET NONE *
3 under each VAT
NOTE 3 below
SET SINGLE LINE SPACING

RESET *
4 -- vacant --
SET

RESET *
5 -- vacant --
SET

RESET *
6 -- vacant --
SET

RESET *
7 -- vacant --
SET

RESET *
8 -- vacant --
SET

NOTE 1: If SET, the VAT symbols (A to H) are printed. They will be programmable in the Print Line Item Name Programming.

NOTE 2: This bit status selection is effective when the following options have been SET.
Address No. 21, Bit No. 2: Tax total amount print
Address No. 21, Bit No. 8: NET total print

NOTE 3: This bit status selection is effective when one of the following options has been SET.
Address No. 21, Bit No. 1: Tax separate print
Address No. 21, Bit No. 3: Taxable total print
Address No. 21, Bit No. 6: NET VAT total separate print

- - Address Nos. 23 to 26 are vacant. - -

6-33

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
1
27 DRAWER OPTION

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

RESET NOT COMPULSORY

Drawer Close
1 Compulsory
NOTE 1 below
SET COMPULSORY *
RESET NON-ACTIVE *
2 Drawer Warning Alarm NOTE 2 below
SET ACTIVE

Single-drawer or Multi-
RESET SINGLE DRAWER *
3 drawer
NOTE 3 below
SET MULTI DRAWER

RESET BY CASHIER *
4 Multi-drawer Control
SET BY CURRENCY

Selection of Change at RESET IN DOMESTIC CURRENCY *

5 Tendering in Foreign NOTE 4 below
Currencies SET IN FOREIGN CURRENCY

Number of Drawers
RESET 1 DRAWER *
6 (if Multi-drawer spec.)
SET 2 DRAWERS

RESET *
7 -- vacant --
SET

RESET *
8 -- vacant --
SET

NOTE 1: If SET, the Drawer-close Compulsory option is active. In this case, when the drawer remains open, any operations except [RF], [JF], [C], numeric
input for Sign-ON are prohibited. This rule is applied in REG, MGR, - , and LOCK modes; in the other modes, the drawer may remain open.

NOTE 2: This bit status selection is effective only when Bit No. 1 is SET. If SET (ACTIVE), the setting in the DRAWER WARNING TIME operation will be
effective. In this operation, a time value in seconds can be set for the time length with the drawer open until the warning alarm generated (the initial
value is 15 seconds).

NOTE 3: If SET, the Multi-drawer specification is selected.

In the case of Cashier Code Entry Method (using [LOG] or [LOG/RECEIPT] key), a drawer is to be designated in sale entries, and the number of
drawers will be further selected at Bit No. 6.
In the case of Cashier Key Method, the drawer to be used will be fixed as in the following:
Drawer 1 for Cashier 1, Drawer 2 for Cashier 2 & all others.

NOTE 4: This bit status selection is available regardless of the status selection for the bit No. 3 and the bit No. 4 in this address.
If RESET, change is returned to a customer by the domestic currency in the foreign currency tendering operation.
If SET, change is returned to a customer by the foreign currency, the symbol “ ” is displayed in the leftmost 2 digits on the 7-segment Numeric
display.
• When change is returned to a customer by the foreign currency, the symbol “ ” will always be displayed even if the option of the cashier No.
display or the PLU price level display (Bits No. 5 and No. 6 of Address No. 4) has been selected.
• When change is returned to a customer by the foreign currency, the Drawer 2 will open if both the bit No. 3 and the bit No. 4 in this address have
been “SET”.

6-34

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
28 OPTIONAL FUNCTION VI

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

No-sale Entry After

RESET ALLOWED *
1 Non-add # Entry
SET PROHIBITED

Number of Times for RESET ANY NUMBER OF TIMES *

2 Non-add # Entries
Within a Receipt SET ONLY ONCE ALLOWED

[RF] Operation During a

RESET ALLOWED *
3 Sale
[JF] is allowed anytime.
SET PROHIBITED

Consecutive No. on
RESET PRINT * Even when NON-PRINT,
4 Receipt and Journal
the Consecutive No. is
SET NON-PRINT counted in memory.

Consecutive No.
RESET NON-RESETTABLE *
5 Resetting
NOTE below
SET RESET ON Financial Daily Z

Negative Mode ( - )
RESET ALLOWED *
6
Operation
SET PROHIBITED

Drawer Open when

RESET OPEN *
7 operating the [TRF] key
SET NOT OPEN

RESET *
8 -- vacant --
SET

NOTE: If SET status is selected, the Consecutive No. will start from “0001” on the first receipt issued after every Financial Daily Reset
Report.

6-35

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
6
29 OPTIONAL FUNCTION VII

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

RESET *
1 -- vacant --
SET

RESET *
2 -- vacant --
SET

RESET *
3 -- vacant --
SET

RESET *
4 -- vacant --
SET

RESET *
5 -- vacant --
SET

RESET PRINT
6 Footer Message Print NOTE below
SET NON-PRINT *
RESET *
7 -- vacant --
SET

RESET *
8 -- vacant --
SET

NOTE: Footer message print is selected.

SET: NON-PRINT
RESET: It is printed under the trailer line (cashier name, consecutive No., current time).

6-36

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
30 OPTIONAL FUNCTION VIII

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

IPD or INPD on Journal RESET IPD *

1 in REG and MGR NOTE 1 below
modes SET INPD

RESET *
2 -- vacant --
SET

RESET *
3 -- vacant --
SET

RESET *
4 -- vacant --
SET

RESET *
5 -- vacant --
SET

RESET PROHIBITED *
6 Cashier Interrupt NOTE 2 below
SET ALLOWED

RESET *
7 -- vacant --
SET

RESET *
8 -- vacant --
SET

NOTE 1: RESET: IPD (Items Printed Detail) ······················Details of the sale entry are printed on journal, just as on receipts.
SET: INPD (Items Not Printed Detail) ·············Details of the Department/PLU entry in REG or MGR mode (excepting
Returned Merchandise, Item Correct, Negative Dept./PLU, Void, All Void) are
omitted on the journal only.

NOTE 2: RESET: Cashier Interrupt function is prohibited.

SET: Cashier Interrupt function is allowed.

6-37

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
31 OPTIONAL FUNCTION IX

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

RESET *
1 -- vacant --
SET

RESET *
2 -- vacant --
SET

Date, day of week, and RESET NON-PRINT *

3 Register No. print on NOTE 1 below
Journal SET PRINT

RESET *
4 -- vacant --
SET

Selection of the Store RESET STORE NAME LOGO *

5 Name Message or Store NOTE 2 below
Name Logo on Receipt SET STORE NAME MESSAGE

RESET * This bit must always be

6 -- vacant --
RESET.
SET

Group Print in All RESET NON-PRINT *

7 Department Read NOTE 3 below
Report SET PRINT

RESET *
8 -- vacant --
SET

NOTE 1: If SET, date, day of week, and register No. are printed on the journal.
In X and Z modes, they are printed on the journal regardless of this bit status selection.

NOTE 2: Either Store Name Message or Store Name Logo is selected. If SET, the Store Name Message specification is active. When
none of store name message has been programmed, its corresponding portion on the receipt will be blank.

NOTE 3: Whether the group is printed on the all department read report is selected. If SET, it will be printed. Additionally, the group is
printed on the reset report regardless of this bit status selection.

6-38

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
32 OPTIONAL FUNCTION X

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

[%+] and [%-] after a

RESET ANY NUMBER OF TIMES *
1 Subtotal within a Sale
SET ONLY ONCE ALLOWED

RESET *
2 -- vacant --
SET

Automatic Cashier Sign

RESET NON-ACTIVE *
3 OFF on finalizing a sale
NOTE 1 below
SET ACTIVE

[% I] key Use (= SFKC

RESET USED AS [%+] KEY *
4 70)
SET USED AS [%-] KEY
NOTE 2 below
[% II] key Use (= SFKC
RESET USED AS [%-] KEY *
5 71)
SET USED AS [%+] KEY
Amount Print on [CRT]
Depression to Finalize a
RESET Sale Total Including PB * Displays Sale Total
6 amount including PB in
Sale including Previous either status
SET Sale Total Excluding PB
Balance

Salesperson Sign-ON
RESET NOT COMPULSORY *
7 Before Sale Item Entries
NOTE 3 below
SET COMPULSORY

Salesperson Sign-ON
RESET ALLOWED *
8 Anytime During a Sale
SET PROHIBITED

NOTE 1: If SET (ACTIVE), the signed-ON cashier will automatically be signed OFF on finalizing each sale. At the automatic cashier sign
OFF, the description “SIGN OFF” is printed neither on the receipt nor on the journal.

NOTE 2: Bit No.4 and No.5 are provided in case your user wants two [%-] keys or two [%+] keys rather one for each.
One [%+] and one [%-] (Standard Bit Status): Bit No. 4…..RESET (%I = %+), Bit No. 5…..RESET (%II = %-)
Two [%-] keys: Bit No. 4…..SET (%I = %-), Bit No. 5…..RESET(%II = %-)
In this case, do not forget to change the Financial Total Name of the %I key.
Two [%+] keys: Bit No. 4…..RESET (%I = %+), Bit No. 5…..SET (%II = %+)
In this case, do not forget to change the Financial Total Name of the %II key.

NOTE 3: NOT COMPULSORY: A Salesperson Sign-ON may or may not be operated for sale entries.
COMPULSORY: A Salesperson must sign ON first of all the sale items of Department, PLU, Amount Discount, Vendor
Coupon, or PB+, PB-, entries.

6-39

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
2
33 OPTIONAL FUNCTION XI

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

Date Set and Print

RESET Follow Bit 2 status * If both RESET, it will be
1 Order YEAR-MONTH-DAY
SET MONTH-DAY-YEAR
order.
(If both SET, it will
RESET Follow Bit 1 status result in MONTH-DAY-
Date Set and Print
2 Order YEAR.)
SET DAY-MONTH-YEAR *
The digit selection (Bit
Special Rounding on
RESET NON-ACTIVE * No. 4) and SPECIAL
3 Sale Total
ROUNDING PROCESS
SET ACTIVE are further necessary.

Number of Digits RESET 1 DIGIT *

4 Subject to Special
Rounding SET 2 DIGITS

Denmark Special RESET NORMAL SP. ROUND *

5 Rounding/Australia NOTE below
DENMARK SP. ROUND/
Special Rounding SET AUSTRALIA SP. ROUND

RESET *
6 -- vacant --
SET

RESET *
7 -- vacant --
SET

RESET *
8 -- vacant --
SET

NOTE: To realize the Denmark Special Rounding feature or the Australia Special Rounding feature, set Bit No.3 through No.5 in this
address as follows.

for Denmark Special Rounding feature

System Option SET RESET Remarks
Special rounding on sale total (Bit No.3) O
Number of digits subject to special rounding (Bit No.4) O 2-digit type
Denmark special rounding (Bit No.5) O
• Set the rounding table of the Denmark Special Rounding in accordance with SPECIAL ROUNDING PROCESS SETTING, 2-
digit type.

for Australia Special Rounding feature

System Option SET RESET Remarks
Special rounding on sale total (Bit No.3) O
Number of digits subject to special rounding (Bit No.4) O 1-digit type
Australia special rounding (Bit No.5) O
• Set the rounding table of the Australia Special Rounding in accordance with SPECIAL ROUNDING PROCESS SETTING, 1-
digit type.

6-40

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
12
34 OPTIONAL FUNCTION XII

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

1
Decimal Point in Item
RESET . (POINT) -- ex) 1.5%
Count and % Rate
SET , (COMMA) * -- ex) 1,5%

2
Amount Division Symbol
between Main and
RESET . (POINT) -- ex) €2.50
Subsidiary digits for
0.00 type
SET , (COMMA) * -- ex) €2,50

3
Amount Division Symbol
between 3rd and 4th
RESET . (POINT) * -- ex) ¥1.000

digits for . - - 0 SET , (COMMA) -- ex) ¥1,000

RESET *
4 -- vacant --
SET

RESET *
5 -- vacant --
SET

RESET *
6 -- vacant --
SET

RESET *
7 -- vacant --
SET

RESET *
8 -- vacant --
SET

- - Address Nos. 35 is vacant. - -

6-41

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
36 FOREIGN CURRENCY OPTION

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

[CUR 1] (Foreign RESET 0.00 ($, €, £, etc.) *

1 Currency 1) Zero-
suppress Display SET . - - 0 (such as Japan yen)

[CUR 2] (Foreign RESET 0.00 ($, €, £, etc.) *

2 Currency 2) Zero-
suppress Display SET . - - 0 (such as Japan yen)

[CUR 3] (Foreign RESET 0.00 ($, €, £, etc.) * These bits selections

3 Currency 3) Zero- are also applied to the
suppress Display SET . - - 0 (such as Japan yen) print.

[CUR 4] (Foreign RESET 0.00 ($, €, £, etc.) *

4 Currency 4) Zero-
suppress Display SET . - - 0 (such as Japan yen)

[CUR 5] (Foreign RESET 0.00 ($, €, £, etc.) *

5 Currency 5) Zero-
suppress Display SET . - - 0 (such as Japan yen)

Foreign Currency RESET NON-PRINT *

6 Tender Amount Print in
payment of a sale SET PRINT
Foreign Currency
Exchange Rate Print in
RESET NON-PRINT *
7
payment or No-sale
SET PRINT
Exchange
Exchange from a
No-sale Exchange from RESET PROHIBITED * Foreign Currency to the
8 Domestic to Foreign
Currencies Domestic currency is
SET ALLOWED
always allowed.

6-42

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
37 OPTIONAL FUNCTION XIII

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

RESET *
1 -- vacant --
SET

Department Memory RESET GROSS PROCESS *

2 Process for %- on
Department Item SET NET PROCESS
NOTE 1 below
PLU Memory Process
RESET GROSS PROCESS *
3 for %- on PLU Item
SET NET PROCESS

Post-issue Receipt Print

RESET ITEMIZED RECEIPT *
4 Form
NOTE 2 below
SET TOTAL-ONLY RECEIPT

RESET *
5 -- vacant --
SET

RESET *
6 -- vacant --
SET
% Calculation on
additional item entries
RESET Calculates on the entire sale *
7 NOTE 3 below
after Subtotal and % Calculates on the additional
SET
entries items
RESET *
8 -- vacant --
SET

NOTE 1: If RESET status (GROSS PROCESS) is selected, %- calculation is performed on the subtotal amount but not processed into
each item memory.
If SET status (NET PROCESS) is selected, %- calculation is performed on each entry item and processed into each item memory.

NOTE 2: If RESET status is selected, a sale of maximum of 30 lines will be issued as an itemized receipt. Exceeding 30 lines, a total-only
receipt will be issued.
If SET status is selected, a total-only receipt will always be issued for the post-issue receipt operation.
• After the [TRF] key operation, the amounts of credit sale total and new balance are printed. The amount of credit sale total is
printed according to the Address No. 32, Bit No. 6 setting (Amount print on [CRT] depression to finalize a sale including
previous balance).
• After the [R/A] key operation, the amounts of received-on-account and the new balance are printed.

NOTE 3: If SET status is selected, % calculation is performed on the additional items entered after the first Subtotal and % entries and
before the second Subtotal and % entries (i.e., on the group subtotal)
ex) Department Entries [ST] [%+] Department Entries [ST] [%-] ..........
(A) (B) Calculates % on the amount of Group (B) not
including Group (A).

6-43

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
38 OPTIONAL FUNCTION XIV

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

RESET *
1 -- vacant --
SET

RESET *
2 -- vacant --
SET

Cashier Identifying RESET CODE ENTRY METHOD *

3 Method: NOTE below
Push SFKC Keys SET PUSH SFKC KEYS

RESET *
4 -- vacant --
SET

RESET *
5 -- vacant --
SET

RESET *
6 -- vacant --
SET

RESET *
7 -- vacant --
SET

RESET *
8 -- vacant --
SET

NOTE: If SET, PUSH SFKC KEYS specification is effective.

CODE ENTRY METHOD: A cashier signs ON by entering a 4-digit code and the [LOG/RECEIPT] key.

PUSH SFKC KEYS: Cashier keys can be programmed on the keyboard by the SFKC programming. A cashier signs ON
by depressing a cashier key assigned on the keyboard. This cashier is valid until another cashier
key is depressed.

6-44

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
39 OPTIONAL FUNCTION XV

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

Money Declaration
RESET PROHIBITED *
1 Operation
NOTE 1 below
SET COMPULSORY

Money Declaration is
RESET EACH CASHIER *
2 performed by:
NOTE 2 below
SET PERMITTED CASHIER

RESET *
3 -- vacant --
SET

RESET *
4 -- vacant --
SET

RESET *
5 -- vacant --
SET

RESET *
6 -- vacant --
SET

RESET *
7 -- vacant --
SET

RESET *
8 -- vacant --
SET

NOTE 1: The Money Declaration Operation Compulsory (SET) status may be selected only when the ECR adopts the PUSH SFKC Keys
Method (not CODE ENTRY method).
• Whether Money Declaration is to be operated by individual cashiers or totally by the permitted cashier is determined by the
Bit No. 2 status selection.
• With this option selected, the following reports cannot be taken: Media Sales and In-drawer Total Read, All Media
Sales Total and Cash-in-Drawer Read, Daily All Cashier Read/Reset, Daily Individual Cashier Read/Reset. (However, when
Bit 2 is SET, the Daily All Cashier Read/Reset Report and the Daily Individual Cashier Read/Reset Report can be printed.)
• When Bit No. 2 is RESET, the Daily Financial Read/Reset Report can be issued only after a Money Declaration operation for
all the cashiers. When Bit No. 2 is set, these reports can be printed by the permitted cashier after performing a Money
Declaration operation.

NOTE 2: If SET status (PERMITTED CASHIER) is selected, the in-drawer amount entries are totally performed by the permitted cashier.
In this case, the media difference memory will not be processed in the Cashier Reports but the Financial Reports.

- - Address Nos. 40 and 41 are vacant. - -

6-45

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106
(Revision Date: Feb. 23, 2007)
6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
42 OPTIONAL FUNCTION XVI

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

RESET *
1 -- vacant --
SET

RESET *
2 -- vacant --
SET

RESET *
3 -- vacant --
SET

RESET *
4 -- vacant --
SET

RESET *
5 -- vacant --
SET

RESET *
6 -- vacant --
SET

Z Counter Print on
RESET PRINT *
7 Reset Reports
NOTE 1 below
SET NON-PRINT
Consecutive No. Print
immediately after the
RESET NON-PRINT *
8 NOTE 2 below
previous daily financial
SET PRINT
reset

NOTE 1: RESET: The Z counter is printed on the reset reports.

SET: The Z counter is not printed on the reset reports, however, only “ z” is printed.
This counter increases by one regardless of this bit status.

NOTE 2: If SET status is selected, the consecutive No. immediately after the previous daily financial reset is printed on the daily financial
reset report. (Columbia specification)
After a RAM Clear or Data Clear, the consecutive No. will be cleared.

- - Address Nos. 43 to 46 are vacant. - -

6-46

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
47 PC OPTION

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

RESET *
1 -- vacant --
SET

RESET *
2 -- vacant --
SET

RESET *
3 -- vacant --
SET

RESET *
4 -- vacant --
SET

RESET *
5 -- vacant --
SET

Zero-skip of PLU Data

RESET PRINT ALL PLU DATA *
6 when transmitting to PC
SET ZERO-SKIP

RESET *
7 -- vacant --
SET

RESET *
8 -- vacant --
SET

- - Address No. 48 is vacant. - -

6-47

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.5 System Option Programming

System Option Table

Standard Bit Set (auto-set by RAM Clear)

ADDRESS NO. CONTENTS
0
49 OPTIONAL FUNCTION XVII

BIT STANDARD
ITEM SELECTIVE STATUS STATUS REMARKS
NO.

Narrow Printing on
RESET STANDARD PRINTING *
1 Journal
NOTE 1 below
SET NARROW PRINTING

RESET *
2 -- vacant --
SET

Disconnection of the
RESET CONNECTED *
3 Journal Printer
NOTE 2 below
SET DISCONNECTED

RESET *
4 -- vacant --
SET

RESET *
5 -- vacant --
SET

RESET *
6 -- vacant --
SET

RESET *
7 -- vacant --
SET

RESET *
8 -- vacant --
SET

NOTE 1: Narrow printing on journal

SET: Journal print is performed with narrow printings.
RESET: Journal print is performed with standard printings.

NOTE 2: If SET status is selected, the Journal Printer is disconnected. Only the receipt print will be performed.
When this status is changed from SET (the Journal Printer is disconnected) to RESET (the Journal Printer is connected), power
off then on the ECR.

6-48

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.6 Commercial Message Programming

6.6 Commercial Message Programming

A maximum of 96 characters of Commercial Message (32 characters x 3 lines) to be printed on the receipt is
programmed here.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu

Depress [1] or [Enter]. “1 MESSAGES” for various message programming is selected.

“1 COMMERCIAL MESSAGE” is selected.

Depress [1] or [Enter]. The message already programmed is displayed.
*
[Enter] The ECR enters the 1st line message input mode.

Input a message in the 1st line. A maximum of 32 one-byte or 16 two-byte characters are input.

[Enter] The 1st line message is entered and the programmed data is printed.

[Enter] The ECR enters the 2nd line message input mode.

Input a message in the 2nd line. A maximum of 32 one-byte or 16 two-byte characters are input.

[Enter] The 2nd line message is entered and the programmed data is printed.

[Enter] The ECR enters the 3rd line message input mode

Input a message in the 3rd line. A maximum of 32 one-byte or 16 two-byte characters are input.

[Enter] The 3rd line message is entered and the programmed data is printed.

This programming is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

*: To program a message in a desired line, move the cursor there with

the [↓] key then depress the [Enter] key.

NOTES:
1. For each line, a maximum of 32 one-byte characters or 16 two-byte characters can be entered.
A combination of both types is also available.
2. If three blank lines are programmed for a commercial message, their portions on the receipt will be closed.
If at least one line message is programmed, the other two lines will be blank.

6-49

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.6 Commercial Message Programming

3) Example:
To program the following Commercial Message.

O p e n 8 : 0 0 a m t o 7 : 0 0 p m
Line No. 1
C l o s e d : e v e r y W e d n e s d a y
Line No. 2
Line No. 3

Operation LCD Display Remarks

When the ECR is being outside a sale

and in SET mode, depress the [1] or
[Enter] key.

Depress the [1] or [Enter] key.

The message already programmed is While ? is shown on the upper-right corner

of the LCD display screen, the [?] key
displayed. depression results in that the following
guidance message appears on the LCD
(To program a message in a desired display.
line, move the cursor there with the [↓]
key then depress the [Enter] key.)

The [Enter] key depression allows the Numbers of programmed characters and of
programmable characters are displayed on
ECR to enter the 1st line message
the 7-segment numeric display.
input mode. (The [C] key depression
clears the message already Example of key operation)
programmed.) The 1st line message is [→] [→] [→] [→] [→] [O] [A/a] [p] [e] [n]
input. [→] [→] [3] [0] [8] [#] [3] [1] [0] [#] [3] [0]
[0] [#] [3] [0] [0] [#] [a] [m] [→] [t] [o] [→]
Number of programmed characters [3] [0] [7] [#] [3] [1] [0] [#] [3] [0] [0] [#] [3]
Number of programmable characters [0] [0] [#] [p] [m] [Enter]

The [Enter] key depression results in When the [Enter] key is depressed, the
message programmed in the 1st line is
that the input message is entered and
printed.
displayed.

The [Enter] key depression allows the Numbers of programmed characters and of
programmable characters are displayed on
ECR to enter the 2nd line message
the 7-segment numeric display.
input mode. (The [C] key depression
clears the message already Example of key operation)
programmed.) The 2nd line message [→] [→] [→] [→] [C] [A/a] [l] [o] [s] [e] [d]
is input. [3] [1] [0] [#] [→] [e] [v] [e] [r] [y] [→][A/a]
[W] [A/a] [e] [d] [n] [e] [s] [d] [a] [y] [Enter]

(continued on the next page)

6-50

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.6 Commercial Message Programming

(continued from the previous page)

Operation LCD Display Remarks

The [Enter] key depression results in When the [Enter] key is depressed, the
message programmed in the 2nd line is
that the input message is entered and printed.
displayed.

The [Enter] key depression allows the Numbers of programmed characters and of
programmable characters are displayed on
ECR to enter the 3rd line message the 7-segment numeric display.
input mode. (The [C] key depression
clears the message already Example of key operation)
programmed.) The 3rd line message [Enter] (No message was input in the 3rd
is input. line.)

The [Enter] key depression results in When the [Enter] key is depressed, the
message programmed in the 3rd line is
that the input message is entered and printed.
displayed.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

NOTE: In the above example, characters except for alphabets are

entered using the character code entry method.

31-10-2005 MON #0

CM NAME
1
Open 8:00am to 7:00pm
2
Closed: every Wednesday
3

0004 13:10TM

6-51

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.7 Footer Message Programming

6.7 Footer Message Programming

A maximum of 64 characters of Footer Message (32 characters x 2 lines) to be printed on the receipt is
programmed here.
Prior to the Footer Message Programming, be sure to select RESET status for Address No. 29, Bit No. 6
of the system option.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu

Depress [1] or [Enter]. “1 MESSAGES” for various message programming is selected.

Depress [↓] then [Enter].

“2 FOOTER MESSAGE” is selected.
or The message already programmed is displayed.
Depress [2].
*
[Enter] The ECR enters the 1st line message input mode.

Input a message in the 1st line. A maximum of 32 one-byte or 16 two-byte characters are input.

[Enter] The 1st line message is entered and the programmed data is printed.

[Enter] The ECR enters the 2nd line message input mode.

Input a message in the 2nd line. A maximum of 32 one-byte or 16 two-byte characters are input.

[Enter] The 2nd line message is entered and the programmed data is printed.

This programming is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

*: To program a message in a desired line, move the cursor there with

the [↓] key then depress the [Enter] key.

NOTES:
1. For each line, a maximum of 32 one-byte characters or 16 two-byte characters can be entered.
A combination of both types is also available.
2. Print format is as shown below.

(Space)
Cashier Name, Consecutive No., Time

Footer Logo Message

6-52

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.7 Footer Message Programming

3) Example:
To program the following Footer Message.

T h a n k y o u Line No. 1
C a l l a g a i n Line No. 2

Operation LCD Display Remarks

When the ECR is being outside a sale

and in SET mode, depress the [1] or
[Enter] key.

Depress the [↓] key. The cursor is moved on to “2 FOOTER

MESSAGE”.

Depress the [2] or [Enter] key.

The message already programmed is While ? is shown on the upper-right corner

of the LCD display screen, the [?] key
displayed. depression results in that the following
guidance message appears on the LCD
display.

The [Enter] key depression allows the Numbers of programmed characters and of
programmable characters are displayed on
ECR to enter the 1st line message
the 7-segment numeric display.
input mode. (The [C] key depression
clears the message already Example of key operation)
programmed.) The 1st line message is [→] [→] [→] [→] [→] [→] [T] [A/a] [h] [a] [n]
input. [k] [→] [A/a] [Y] [A/a] [o] [u] [Enter]

(To program a message in a desired Number of programmed characters

line, move the cursor there with the [↓] Number of programmable characters
key then depress the [Enter] key.)

The [Enter] key depression results in When the [Enter] key is depressed, the
message programmed in the 1st line is
that the input message is entered and
printed.
displayed.

(continued on the next page)

6-53

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.7 Footer Message Programming

(continued from the previous page)

Operation LCD Display Remarks

The [Enter] key depression allows the Numbers of programmed characters and of
programmable characters are displayed on
ECR to enter the 2nd line message the 7-segment numeric display.
input mode. (The [C] key depression
clears the message already Example of key operation)
programmed.) The 2nd line message [→] [→] [→] [→] [→] [→] [→] [→] [→] [→]
is input. [→] [→] [→] [→] [→] [→] [C] [A/a] [a] [l] [l]
[→] [a] [g] [a] [i] [n] [Enter]

The [Enter] key depression results in When the [Enter] key is depressed, the
message programmed in the 2nd line is
that the input message is entered and
printed.
displayed.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

NOTE: In the above example, characters except for alphabets are

entered using the character code entry method.

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

FOOTER NAME
1
Thank You
2
Call again

0004 13:13TM

6-54

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.8 Store Name Message Programming

6.8 Store Name Message Programming

A maximum of 128 characters of Store Name Message (32 characters x 4 lines) to be printed on the receipt is
programmed here.
Prior to the Store Name Message Programming, be sure to select SET status for Address No. 31, Bit No. 5
of the system option.

CONDITION Any time outside a sale

OPERATION
Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu

Depress [1] or [Enter]. “1 MESSAGES” for various message programming is selected.

Depress [↓] twice then [Enter].

“3 STORE MESSAGE” is selected.
or The message already programmed is displayed.
Depress [3].
*
[Enter] The ECR enters the 1st line message input mode

Input a message in the 1st line. A maximum of 32 one-byte or 16 two-byte characters are input.

[Enter] The 1st line message is entered and the programmed data is printed.

[Enter] The ECR enters the 2nd line message input mode

Input a message in the 2nd line. A maximum of 32 one-byte or 16 two-byte characters are input.

[Enter] The 2nd line message is entered and the programmed data is printed.

[Enter] The ECR enters the 3rd line message input mode

Input a message in the 3rd line. A maximum of 32 one-byte or 16 two-byte characters are input.

[Enter] The 3rd line message is entered and the programmed data is printed.

[Enter] The ECR enters the 4th line message input mode

Input a message in the 4th line. A maximum of 32 one-byte or 16 two-byte characters are input.

[Enter] The 4th line message is entered and the programmed data is printed.

This programming is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.
*: To program a message in a desired line, move the cursor there with
the [↓] key then depress the [Enter] key.

6-55

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.8 Store Name Message Programming

NOTES: 1. For each line, a maximum of 32 one-byte characters or 16 two-byte characters can be entered.
A combination of both types is also available.
2. When blanks are entered for the whole one line, it results in one line feed.
3. When the store name message specification has been selected, the 4-line range assigned for the
store name message is either printed or fed, regardless of any system option selection.
4. Print format for each specification is as shown below.

1) Store Name Logo specification

When Commercial Message is SET When Commercial Message is RESET

Store Name Logo Store Name Logo

Date, Register No.

Commercial Message (Space)
Description
(Space)
Date, Register No.
(Space)
Description

2) Store Name Message specification

When Commercial Message is SET When Commercial Message is RESET

Store Name Message Store Name Message

(Space)
Commercial Message
Date, Register No.
(Space)
(Space)
Description
Date, Register No.
(Space)
Description

6-56

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.8 Store Name Message Programming

3) Example:
To program the following Store Message.

T E C S T O R E Line No. 1
1 3 4 3 P E A C H D R I V E Line No. 2
P H O N E : 8 7 - 6 4 3 7 Line No. 3
Line No. 4

Operation LCD Display Remarks

When the ECR is being outside a sale

and in SET mode, depress the [1] or
[Enter] key.

Depress the [↓] key twice. The cursor is moved on to “3 STORE

MESSAGE”.

Depress the [3] or [Enter] key.

The message already programmed is While ? is shown on the upper-right corner

of the LCD display screen, the [?] key
displayed. depression results in that the following
guidance message appears on the LCD
display.

The [Enter] key depression allows the To program a message in a desired line,
ECR to enter the 1st line message move the cursor there with the [↓] key then
depress the [Enter] key.
input mode. (The [C] key depression
clears the message already Numbers of programmed characters and of
programmed.) The 1st line message is programmable characters are displayed on
input. the 7-segment numeric display.
Number of programmed characters
Number of programmable characters

The [Enter] key depression results in When the [Enter] key is depressed, the
message programmed in the 1st line is
that the input message is entered and
printed.
displayed.
Example of key operation)
[→] [→] [→] [→] [→] [→][→] [Dbl] [T] [E]
[C] [→] [S] [T] [O] [R] [E] [Enter]

The [Enter] key depression allows the Numbers of programmed characters and of
programmable characters are displayed on
ECR to enter the 2nd line message
the 7-segment numeric display.
input mode. (The [C] key depression
clears the message already
programmed.) The 2nd line message
is input.
(continued on the next page)

6-57

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.8 Store Name Message Programming

(continued from the previous page)

Operation LCD Display Remarks

The [Enter] key depression results in When the [Enter] key is depressed, the
message programmed in the 2nd line is
that the input message is entered and printed.
displayed.
Example of key operation)
[→] [→] [→] [→] [→] [→] [→] [3] [0] [1] [#]
[3] [0] [3] [#] [3] [0] [4] [#] [3] [0] [3] [#] [→]
[P] [E] [A] [C] [H] [→] [D] [R] [I] [V] [E]
[Enter]

The [Enter] key depression allows the Numbers of programmed characters and of
programmable characters are displayed on
ECR to enter the 3rd line message
the 7-segment numeric display.
input mode. (The [C] key depression
clears the message already
programmed.) The 3rd line message
is input.

The [Enter] key depression results in When the [Enter] key is depressed, the
message programmed in the 3rd line is
that the input message is entered and
printed.
displayed.
Example of key operation)
[→] [→] [→] [→] [→] [→] [→][→] [P] [H] [O]
[N] [E] [3] [1] [0] [#] [→] [3] [0] [8] [#] [3] [0]
[7] [#] [2] [1] [3] [#] [3] [0] [6] [#] [3] [0] [4]
[#] [3] [0] [3] [#] [3] [0] [7] [#] [Enter]

The [Enter] key depression allows the Numbers of programmed characters and of
programmable characters are displayed on
ECR to enter the 4th line message
the 7-segment numeric display.
input mode. (The [C] key depression
clears the message already
programmed.) The 4th line message is
input.

The [Enter] key depression results in When the [Enter] key is depressed, the
message programmed in the 4th line is
that the input message is entered and
printed.
displayed.
Example of key operation)
[Enter] (No message is input.)

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

NOTE: In the above example, characters except for alphabets are

entered using the character code entry method.
Open 8:00am to 7:00pm
Closed: every Wednesday

31-10-2005 MON #0

STORE NAME
1
TEC STORE
2
1343 PEACH DRIVE
3
PHONE: 87-6437

0005 13:15TM

6-58

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.9 Department Name Programming

6.9 Department Name Programming

A maximum of 16 characters of department name is programmed here.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] then [Enter].

or “2 NAMES” for various name programming is selected.
Depress [2].

Depress [2] or [Enter] key. “1 DP KEY NAME” is selected.

Select a department of which name is

to be programmed with the [↑] or [↓] The department name already programmed is displayed.
key.

[Enter] The ECR enters character input mode.

Input a department name. A maximum of 16 one-byte or 8 two-byte characters are input.

[Enter] The department name is entered and printed.

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

NOTE: A maximum of 16 one-byte characters or 8 two-byte characters can be entered. A combination of

both types is also available.

6-59

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.9 Department Name Programming

3) Example
To program “FOOD” as the name of Department 01.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “2 NAMES”.
and in SET mode, depress the [↓] key.

Depress the [2] or [Enter] key. “2 NAME” is selected.

Depress the [1] or [Enter] key. “1 DP KEY NAME” is selected.

Depress the [Enter] key. When programming a name of another

department, move the cursor on to a desired
department with the [↓] or [↑] key, then
(Department 01 is selected.) depress the [Enter] key.

The [C] key depression clears the The department name already programmed
is displayed.
department name already
programmed.

Input a desired name. Numbers of programmed characters and of

programmable characters are displayed on
the 7-segment numeric display.

Example of key operation)

[F] [O] [O] [D] [Enter]

The [Enter] key depression results in When the [Enter] key is depressed, the
programmed data is printed.
that the input name is entered and
displayed.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

DP NAME
01 FOOD

0006 13:17TM

6-60

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.10 Department Group Name Programming

6.10 Department Group Name Programming

In this operation, the name of each Department Group is programmed. Which Departments are linked to each
Group has been set in the DEPARTMENT TABLE PROGRAMMING operation. A maximum of 15 department
groups can be set.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] then [Enter].

or “2 Names” is selected.
Depress [2].

Depress [↓] then [Enter].

or “2 DP GROUP NAME” is selected.
Depress [2].

Select a department group of which

name is to be programmed with the [↑] The department group name already programmed is displayed.
or [↓] key.

[Enter] The ECR enters character input mode.

Input a department group name. A maximum of 12 one-byte or 6 two-byte characters are input.

[Enter] The department group name is entered and printed.

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

NOTE: A maximum of 12 one-byte characters or 6 two-byte characters can be entered. A combination of both
types is also available.

3) Example
To program the following name on Department Group 1:
Group 1 F R E S H

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “2 NAMES”.
and in SET mode, depress the [↓] key.

(continued on the next page)

6-61

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.10 Department Group Name Programming

(continued from the previous page)

Operation LCD Display Remarks

Depress the [2] or [Enter] key. “2 NAMES” is selected.

Depress the [↓] key. The cursor is moved on to “2 DP GROUP

NAME”.

Depress the [2] or [Enter] key. “2 DP GROUP NAME” is selected.

Depress the [Enter] key. When programming a name of another

department group, move the cursor on to a
desired one with the [↓] or [↑] key, then
(Department Group 1 is selected.) depress the [Enter] key.

The [C] key depression clears the The department group name already
programmed is displayed.
department group name already
programmed.

Input a desired name. Numbers of programmed characters and of

programmable characters are displayed on
the 7-segment numeric display.

Example of key operation)

[Dbl] [F] [R] [E] [S] [H] [Enter]

The [Enter] key depression results in When the [Enter] key is depressed, the
programmed data is printed.
that the input name is entered and
displayed.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

GROUP
01 FRESH

0007 13:19TM

6-62

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.11 Cashier Name and Status Programming

6.11 Cashier Name and Status Programming

Cashier Name and Cashier Status for each cashier can be programmed here.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] then [Enter].

or “2 NAMES” for various name programming is selected.
Depress [2].

Depress [↓] twice then [Enter].

“3 CASHIER NAME” is selected.
or The cashier name already programmed is displayed.
Depress [3].

Select a cashier to be programmed

The [Enter] key depression allows the ECR to enter the programming
with the [↑] or [↓] key, then depress mode for a desired cashier. (Cashiers 1 to 8 are programmable.)
[Enter].

[Enter] The ECR enters character input mode.

Input a cashier name. A maximum of 12 one-byte or 6 two-byte characters are input.

[Enter] The cashier name is entered and displayed.

[Enter] The ECR enters the cashier status input mode.

Select a cashier status with the [↑] or The two statuses below are set/reset. (N: Reset, Y: Set)
[↓] key, then depress the [→] key to 01 Training
set/reset the status. 02 All MDR

[Enter] The programmed data is printed.

*
[End] This programming is ended. A long receipt is issued and the display
returns to Main Menu screen.

*: Depress the [Rtn] key to program another cashier.

6-63

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.11 Cashier Name and Status Programming

NOTES:
1. Cashiers 1 to 8 are programmed with the names “1CL” to “8CL” as default setting.
2. For the name of each cashier, a maximum of 12 one-byte or 6 two-byte characters can be entered.
A combination of both types is also available.
3. Training entry status is available for every cashier.
4. Prior to the change of cashier status (Normal cashier → Training cashier, or Training cashier → Normal
Cashier), daily reports and GT reports of this cashier should be taken.

3) Example
To program the following cashier data.
Cashier 1: JONES (cashier name), Training Cashier (status)

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “2 NAMES”.
and in SET mode, depress the [↓] key.

Depress the [2] or [Enter] key. “2 NAMES” is selected.

Depress the [↓] key twice. The cursor is moved on to “3 CASHIER

NAME”.

Depress the [3] or [Enter] key. “3 CASHIER NAME” is selected.

The cashier name already While ? is shown on the upper-right corner

of the LCD display screen, the [?] key
programmed is displayed. depression results in that the following
guidance message appears on the LCD
display.

The [Enter] key depression allows the While ? is shown on the upper-right corner
of the LCD display screen, the [?] key
ECR to enter Cashier 1 programming
depression results in that the following
mode menu. guidance message appears on the LCD
display.
(To program a desired cashier, select
the cashier with the [↓] key then
depress the [Enter] key.)

(continued on the next page)

6-64

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.11 Cashier Name and Status Programming

(continued from the previous page)

Operation LCD Display Remarks

The [Enter] key depression allows the Numbers of programmed characters and of
programmable characters are displayed on
ECR to enter the cashier 1 name input the 7-segment numeric display.
mode. (The [C] key depression clears
the name already programmed.) The
cashier 1 name is input.
Example of key operation)
Number of programmed characters [J] [O] [N] [E] [S] [Enter]
Number of programmable characters

The [Enter] key depression results in The [?] key depression results in that the
following guidance message appears on the
that the input name is entered and
LCD display.
displayed.

The next [Enter] key depression The [?] key depression results in that the
following guidance message appears on the
allows the ECR to enter the cashier 1
LCD display.
status input mode.

Select the status of 01 TRAINING with

the [→] key.

The [Enter] key depression results in When the [Enter] key is depressed, the
programmed data is printed.
that the Cashier 1 programming data is
entered.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

CASHIER
01
#01 JONES
#02 1

0008 13:21TM

6-65

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.12 PLU Name Programming

6.12 PLU Name Programming

A maximum of 16 characters of PLU name is programmed here.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] then [Enter].

or “2 NAMES” for various name programming is selected.
Depress [2].

Depress the [↓] key three times then

[Enter]. “4 PLU (ITEM NO.) NAME” is selected.
or
Depress [4].

Select a PLU of which name is to be

The PLU name already programmed is displayed.
programmed with the [↑] or [↓] key.

[Enter] The ECR enters character input mode.

Input a PLU name. A maximum of 16 one-byte or 8 two-byte characters are input.

[Enter] The PLU name is entered and printed.

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

NOTE: A maximum of 16 one-byte characters or 8 two-byte characters can be entered. A combination of

both types is also available.

3) Example
To program “Tomato” as the name of PLU Code No. 0001.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “2 NAMES”.
and in SET mode, depress the [↓] key.

(continued on the next page)

6-66

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.12 PLU Name Programming

(continued from the previous page)

Operation LCD Display Remarks

Depress the [2] or [Enter] key.

Depress the [↓] key three times. The cursor is moved on to “4 PLU (ITM NO.)
NAME”.

Depress the [4] or [Enter] key. “4 PLU (ITM NO.) NAME” is selected.

Depress the [Enter] key. When programming a name of another PLU,

move the cursor on to a desired PLU with the
[↓] or [↑] key, then depress the [Enter] key.
(PLU Code No. 0001 is selected.)

The [C] key depression clears the PLU The PLU name already programmed is
displayed.
name already programmed.

Input a desired name. Numbers of programmed characters and of

programmable characters are displayed on
the 7-segment numeric display.

Example of key operation)

[T] [A/a] [o] [m] [a] [t] [o] [Enter]

The [Enter] key depression results in When the [Enter] key is depressed, the
programmed data is printed.
that the input name is entered and
displayed.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

PLU NAME
0001 Tomato

0009 13:23TM

6-67

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.13 Salesperson Name Programming

6.13 Salesperson Name Programming

By programming Salesperson here, the name of each salesperson can be programmed in a maximum of 12
characters.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] then [Enter].

or “2 NAMES” is selected.
Depress [2].

Depress the [↓] key four times then

[Enter] key. “5 SALESPERSON NAME” is selected.
or
Depress [5].

Select a salesperson of which name is

to be programmed with the [↑] or [↓] The salesperson name already programmed is displayed.
key.

[Enter] The ECR enters character input mode.

Input a salesperson name. A maximum of 12 one-byte or 6 two-byte characters are input.

[Enter] The salesperson name is entered and printed.

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

NOTES:
1. A maximum of 30 salesperson names can be set. The salesperson codes 1 to 30 are fixed.
2. A maximum of 12 one-byte characters or 6 two-byte characters can be entered. A combination of both types
is also available.

6-68

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.13 Salesperson Name Programming

3) Example
To program “White” on Salesperson Code 01:

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “2 NAMES”.
and in SET mode, depress the [↓] key.

Depress the [2] or [Enter] key. “2 NAMES” is selected.

Depress the [↓] key four times. The cursor is moved on to

”5 SALESPERSON NAME”.

Depress the [5] or [Enter] key. ”5 SALESPERSON NAME” is selected.

Depress the [Enter] key. While ? is shown on the upper-right corner

of the LCD display screen, the [?] key
depression results in that the following
(Salesperson 01 is selected.) guidance message appears on the LCD
display.

The [C] key depression clears the The salesperson name already programmed
is displayed.
salesperson name already
programmed.

Input a desired name. Numbers of programmed characters and of

programmable characters are displayed on
the 7-segment numeric display.

Example of key operation)

[W] [A/a] [h] [I] [t] [e] [Enter]

The [Enter] key depression results in When the [Enter] key is depressed, the
programmed data is printed.
that the input name is entered and
displayed.

(continued on the next page)

6-69

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.13 Salesperson Name Programming

(continued from the previous page)

Operation LCD Display Remarks

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

SALES PERSON
01 White

0010 13:25TM

6-70

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.14 Financial Report Item Name Programming

6.14 Financial Report Item Name Programming

Item Names printed on Financial Report are programmed here. Many of them are also printed on sales receipts.
Other Line Item Names will be programmed in 6.15 Print Line Item Name Programming.

CONDITION After Financial Reset

OPERATION
Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] then [Enter].

or “2 NAMES” is selected.
Depress [2].

Depress the [↓] key five times then

[Enter] key. “6 FINANCIAL ITM NAME” is selected.
or
Depress [6].

Select a Financial item name of which

name is to be programmed with the [↑] The financial item name already programmed is displayed.
or [↓] key.

[Enter] The ECR enters character input mode.

Input a Financial item name. A maximum of 12 one-byte or 6 two-byte characters are input.

[Enter] The financial item name is entered and printed.

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

NOTES:
1. As for most items, a maximum of 12 regular-sized or 6 double-sized characters may be programmed for one
item name.
2. As shown in the table on the following pages, the standard program data are pre-programmed (which is
auto-set after a RAM Clear). Therefore, program only the items that need to be changed.

6-71

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.14 Financial Report Item Name Programming

3) Example
To program “NET GT” instead of “NET GT” for Item Code 2 (NET GT) all in double-sized characters.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “2 NAMES”.
and in SET mode, depress the [↓] key.

Depress the [2] or [Enter] key. “2 NAMES” is selected.

Depress the [↓] key five times. The cursor is moved on to

”6 FINANCIAL ITM NAME”.

Depress the [6] or [Enter] key. ”6 FINANCIAL ITM NAME” is selected.

Depress the [↓] key, then depress the While ? is shown on the upper-right corner
of the LCD display screen, the [?] key
[Enter] key. depression results in that the following
guidance message appears on the LCD
(Item code 2 (“NET GT”) is selected.) display.

The [C] key depression clears the The financial item name already
programmed is displayed.
financial item name already
programmed.

Input a desired name. Numbers of programmed characters and of

programmable characters are displayed on
the 7-segment numeric display.

Example of key operation)

[Dbl] [N] [E] [T] [→] [G] [T] [Enter]

The [Enter] key depression results in When the [Enter] key is depressed, the
programmed data is printed.
that the input name is entered and
displayed.

(continued on the next page)

6-72

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.14 Financial Report Item Name Programming

(continued from the previous page)

Operation LCD Display Remarks

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

FINANCIAL
#002 NET GT

0011 13:27TM

Financial Report Item Name Table

Item
Item Name Standard Program
Code
1 Ground Total G T
2 NET GT N E T G T
3 NEG GT N E G G T
4 Gross Sale G S
5 Tax 1 (Add-on Tax 1) T A X 1
6 Tax 2 (Add-on Tax 2) T A X 2
7 Tax 3 (Add-on Tax 3) T A X 3
8 Tax 4 (Add-on Tax 4) T A X 4
9 Tax 5 (Add-on Tax 5) T A X 5
10 Tax 6 (Add-on Tax 6) T A X 6
11 Tax 7 (Add-on Tax 7) T A X 7
12 Tax 8 (Add-on Tax 8) T A X 8
13 Tax Total T A X T L
14 Net Sale with Tax N S
15 % I (usually %+) % +
16 % II (usually %-) % -
17 Vendor Coupon V . C P N
18 Amount Discount D I S C
19 Negative Depts. Total - D P T L
20 Special Round Fractions S P . R N D
21 Net Sale (All-Media Sales) N S
22 Cash Sales (AT/TL) C A S H
23 Media 1 Sales (CHK) C H E C K
24 Media 2 Sales (CRT) C R T
25 Media 3 Sales (MISC) M I S C

6-73

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.14 Financial Report Item Name Programming

Financial Report Item Name Table (continued)

Item
Item Name Standard Program
Code
26 Media 4 Sales (CPN) C P N
27 Media 5 Sales (Credit 1) C R T T L 1
28 Media 6 Sales (Credit 2) C R T T L 2
28 Media 7 Sales (Credit 3) C R T T L 3
30 Media 8 Sales (Credit 4) C R T T L 4
31 Media 9 Sales (Credit 5) C R T T L 5
32 Received-on-Account R / A
33 Paid-Out P O
34 Cash-in-drawer C A S H I D
35 Cash-in-drawer (Foreign Currency 1) C A S H C U R 1 I D
36 Cash-in-drawer (Foreign Currency 2) C A S H C U R 2 I D
37 Cash-in-drawer (Foreign Currency 3) C A S H C U R 3 I D
38 Cash-in-drawer (Foreign Currency 4) C A S H C U R 4 I D
39 Cash-in-drawer (Foreign Currency 5) C A S H C U R 5 I D
40 Media 1-in-drawer (CHK) C H E C K I D
41 Cheque-in-drawer (Foreign Currency 1) C K C U R 1 I D
42 Cheque-in-drawer (Foreign Currency 2) C K C U R 2 I D
43 Cheque-in-drawer (Foreign Currency 3) C K C U R 3 I D
44 Cheque-in-drawer (Foreign Currency 4) C K C U R 4 I D
45 Cheque-in-drawer (Foreign Currency 5) C K C U R 5 I D
46 Media 2-in-drawer (CRT) C R T I D
47 Credit-in-drawer (Foreign Currency 1) C R T C U R 1 I D
48 Credit-in-drawer (Foreign Currency 2) C R T C U R 2 I D
49 Credit-in-drawer (Foreign Currency 3) C R T C U R 3 I D
50 Credit-in-drawer (Foreign Currency 4) C R T C U R 4 I D
51 Credit-in-drawer (Foreign Currency 5) C R T C U R 5 I D
52 Media 3-in-drawer (MISC) M I S C I D
53 MISC-in-drawer (Foreign Currency 1) M I S C C U R 1 I D
54 MISC-in-drawer (Foreign Currency 2) M I S C C U R 2 I D
55 MISC-in-drawer (Foreign Currency 3) M I S C C U R 3 I D
56 MISC-in-drawer (Foreign Currency 4) M I S C C U R 4 I D
57 MISC-in-drawer (Foreign Currency 5) M I S C C U R 5 I D
58 Media 4-in-drawer (CPN) C P N I D
59 Coupon-in-drawer (Foreign Currency 1) C P N C U R 1 I D
60 Coupon-in-drawer (Foreign Currency 2) C P N C U R 2 I D
61 Coupon-in-drawer (Foreign Currency 3) C P N C U R 3 I D
62 Coupon-in-drawer (Foreign Currency 4) C P N C U R 4 I D
63 Coupon-in-drawer (Foreign Currency 5) C P N C U R 5 I D
64 Media 5-in-drawer (Credit 1) C R T I D 1
65 Media 6-in-drawer (Credit 2) C R T I D 2
66 Media 7-in-drawer (Credit 3) C R T I D 3
67 Media 8-in-drawer (Credit 4) C R T I D 4
68 Media 9-in-drawer (Credit 5) C R T I D 5
69 Cash-in-drawer Difference C A S H D I F
70 Media 1-in-drawer Difference C K D I F

6-74

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.14 Financial Report Item Name Programming

Financial Report Item Name Table (continued)

Item
Item Name Standard Program
Code
71 Media 2-in-drawer Difference C R T D I F
72 Media 3-in-drawer Difference M I S C D I F
73 Media 4-in-drawer Difference C P N D I F
74 Media 5-in-drawer Difference C R T 1 D I F
75 Media 6-in-drawer Difference C R T 2 D I F
76 Media 7-in-drawer Difference C R T 3 D I F
77 Media 8-in-drawer Difference C R T 4 D I F
78 Media 9-in-drawer Difference C R T 5 D I F
79 Item Correct C O R R
80 Void V O I D
81 Misc. Void M I S C V D
82 All Void A L L V D
83 Store Coupon S . C P N
84 Returned Merchandise R T N
85 Negative Mode Total R E G -
86 %- on Line Items % -
87 Amount Discount on Line Items D I S C
88 Transfer Balance GT T R F T L
89 Transfer + GT T R F + G T
90 Transfer – GT T R F - G T
91 Transfer + Daily T R F +
92 Transfer – Daily T R F -
93 PB (Previous Balance) Sales P B T L
94 PB R/A (PB Paid) P B R / A
95 PB PO (PB Refunded) P B P O
96 Taxable Total 1 T X B L 1
97 VAT 1 or Tax 1 V A T 1
98 Taxable Total 2 T X B L 2
99 VAT 2 or Tax 2 V A T 2
100 Taxable Total 3 T X B L 3
101 VAT 3 or Tax 3 V A T 3
102 Taxable Total 4 T X B L 4
103 VAT 4 or Tax 4 V A T 4
104 Taxable Total 5 T X B L 5
105 VAT 5 or Tax 5 V A T 5
106 Taxable Total 6 T X B L 6
107 VAT 6 or Tax 6 V A T 6
108 Taxable Total 7 T X B L 7
109 VAT 7 or Tax 7 V A T 7
110 Taxable Total 8 T X B L 8
111 VAT 8 or Tax 8 V A T 8
112 VAT Total V A T T L
113 Net Sale Without Tax N . N S
114 Tax-exempt Customer V A T E X
115 VAT 1 or Tax 1 Exempt V A T 1 E X

6-75

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.14 Financial Report Item Name Programming

Financial Report Item Name Table (continued)

Item
Item Name Standard Program
Code
116 VAT 2 or Tax 2 Exempt V A T 2 E X
117 VAT 3 or Tax 3 Exempt V A T 3 E X
118 VAT 4 or Tax 4 Exempt V A T 4 E X
119 VAT 5 or Tax 5 Exempt V A T 5 E X
120 VAT 6 or Tax 6 Exempt V A T 6 E X
121 VAT 7 or Tax 7 Exempt V A T 7 E X
122 VAT 8 or Tax 8 Exempt V A T 8 E X
123 Sales Item Count per Customer I T E M / C U S
124 Sales Amount per Customer T L / C U S
125 No-Sale Counter N O S A L E
126 [C] key Counter C L E A R
127 Consignment Counter C O N S I G N C T R
128 Validation Counter V A L I C T R
129 Money Declaration Counter M . D C R
130 -- vacant --

6-76

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.15 Print Line Item Name Programming

6.15 Print Line Item Name Programming

Print Line Item Names not listed in Section 6.14 Financial Report Item Name Programming can be
programmed here.

CONDITION Anytime outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] then [Enter].

or “2 NAMES” is selected.
Depress [2].

Depress the [↓] key six times then

[Enter] key. “7 PRINT ITEM NAME” is selected.
or
Depress [7].

Select a print item name of which name

is to be programmed with the [↑] or [↓] The print line item name already programmed is displayed.
key.

[Enter] The ECR enters character input mode.

Input a print line item name. NOTE 1 below

[Enter] The print line item name is entered and printed.

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

NOTES:
1. The maximum number of characters programmable for each item are shown in the table on the following
pages. Please note that some items require their name entries as one set. The maximum number of
characters in the table shows the capacity in one-byte characters. A two-byte character occupies two one-
byte characters’ space. (Also refer to CHARACTER ENTRIES at the beginning of this chapter.)
2. As shown in the table on the following pages, the standard program data are preprogrammed which is auto-
set after a RAM Clear). Therefore, program only the items that need to be changed.

6-77

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.15 Print Line Item Name Programming

3) Example
To program the amount mark “€” in Item Code 7: (The amount mark has not been preset as the standard
program data).
Meanwhile, the names of the other items in the Item Code 7 should remain unchanged as the standard
program data (i.e. “@” for Unit Price Symbol and “ITEM” for Sale Item Count Symbol).

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “2 NAMES”.
and in SET mode, depress the [↓] key.

Depress the [2] or [Enter] key. “2 NAMES” is selected.

Depress the [↓] key six times. The cursor is moved on to

”7 PRINT ITEM NAME”.

Depress the [7] or [Enter] key. ”7 PRINT ITEM NAME” is selected.

Depress the [↓] key six times, then While ? is shown on the upper-right corner
of the LCD display screen, the [?] key
depress the [Enter] key. depression results in that the following
guidance message appears on the LCD
(Item code 7 (“@ ITEM ”) is selected.) display.

The [C] key depression clears the print The print line item name already
programmed is displayed.
line item name already programmed.

Input a desired name. Numbers of programmed characters and of

programmable characters are displayed on
the 7-segment numeric display.

Example of key operation)

400[#] 900[#] [I] [T] [E] [M] [→] [Enter]

The [Enter] key depression results in When the [Enter] key is depressed, the
programmed data is printed.
that the input name is entered and
displayed.

(continued on the next page)

6-78

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.15 Print Line Item Name Programming

(continued from the previous page)

Operation LCD Display Remarks

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

PRINT NAME
#007 @€ITEM

0012 13:29TM

Print Line Item Name Table

Max. Number of Characters
Item
Item Name or Application Standard Program
Code
1 Subtotal in transactions S U B T L 8
2 Cash Tendered in transactions C A T E N D 8
3 Sale Total of each transaction T O T A L 8
4 Change due in transactions C H A N G E 8
5 Cash Refunded C A S H 8
6 Negative Department Total - T O T A L 8
The following items must be set together. (NOTE 1) @ I T E M 7
Unit Price Symbol 1
7 Amount Mark (€, $,etc.) 1
Sale Item Count Symbol on Receipt 4
Unit Price Symbol on Quantity Extension 1
The following items must be set together. (NOTE 2) # C L T M 6
Register No. Symbol 2
8
Cashier/Clerk Symbol 2
Time Symbol 2
9 Customer Count (on reports) C U 2
10 -- vacant -- ---
11 Previous Balance (Credit) (NOTE 5) P B + 8
12 Previous Balance (Debit) (NOTE 5) P B - 8
13 Transferred Amount in Charge Posting N E W B A L 8
14 Item Correct C O R R ↑ 8
The following items must be set together. O N O F F 8
15 ON portion of Training ON/OFF 4
OFF portion of Training ON/OFF 4

6-79

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.15 Print Line Item Name Programming

Print Line Item Name Table (continued)

Max. Number of Characters
Item
Item Name or Application Standard Program
Code
VAT symbol (VAT 1 to VAT8) A B C D E F G H 8
VAT 1 symbol 1
VAT 2 symbol 1
VAT 3 symbol 1
16 VAT 4 symbol 1
VAT 5 symbol 1
VAT 6 symbol 1
VAT 7 symbol 1
VAT 8 symbol 1
17 -- vacant -- ---
18 -- vacant -- ---
19 Post-issue Receipt Header C O P Y 10
20 PLU Symbol (when no name is programmed for the PLU) P L U 3
21 Taxable Total T X B L T L 8
22 -- vacant -- ---
23 -- vacant -- ---
24 -- vacant -- ---
25 -- vacant -- ---
26 -- vacant -- ---
27 -- vacant -- ---
Sunday, Monday (as part of the date print line) S U N M O N 8
28 Sunday 4
Monday 4
Tuesday, Wednesday (as part of the date print line) T U E W E D 8
29 Tuesday 4
Wednesday 4
Thursday, Friday (as part of the date print line) T H U F R I 8
30 Thursday 4
Friday 4
31 Saturday (as part of the date print line) S A T 4
32 Training ON/OFF operation, Cashier Report T R A I N I N G 10
33 Cashier Sign ON S I G N O N 10
34 Cashier Sign OFF S I G N O F F 10
35 -- vacant -- ---
36 -- vacant -- ---
37 -- vacant -- ---
38 % calculation on Additional Item Entries after Subtotal and % entries G R P . S T 8
39 -- vacant -- ---
40 Receipt Buffer R E C E I P T B U F 12
41 -- vacant --
42 -- vacant -- ---
43 -- vacant -- ---
44 -- vacant -- ---
45 -- vacant -- ---
46 -- vacant -- ---
47 -- vacant -- ---
48 -- vacant -- ---
49 -- vacant -- ---
Foreign Currency 1 (for Sales Entry, Programming,
50 Program Data Read) C U R 1 12

6-80

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.15 Print Line Item Name Programming

Print Line Item Name Table (continued)

Max. Number of Characters
Item
Item Name or Application Standard Program
Code
Foreign Currency 2 (for Sales Entry, Programming,
51 Program Data Read) C U R 2 12
Foreign Currency 3 (for Sales Entry, Programming,
52 Program Data Read) C U R 3 12
Foreign Currency 4 (for Sales Entry, Programming,
53 Program Data Read) C U R 4 12
Foreign Currency 5 (for Sales Entry, Programming,
54 Program Data Read) C U R 5 12
55 -- vacant -- ---
60 -- vacant -- ---
61 -- vacant -- ---
62 -- vacant -- ---
63 -- vacant -- ---
64 -- vacant -- ---
65 NET Total N E T T L 12
66 VAT/TAX V A T 8
67 Consignment C O N S I G N M E N T 12
68 NET TL1 N E T T L 1 12
69 NET TL2 N E T T L 2 12
70 NET TL3 N E T T L 3 12
71 NET TL4 N E T T L 4 12
72 NET TL5 N E T T L 5 12
73 NET TL6 N E T T L 6 12
74 NET TL7 N E T T L 7 12
75 NET TL8 N E T T L 8 12
76 -- vacant -- ---
77 -- vacant -- ---
78 -- vacant -- ---
79 -- vacant -- ---
80 -- vacant -- ---
81 -- vacant -- ---
82 -- vacant -- ---
83 -- vacant -- ---
84 -- vacant -- ---
85 -- vacant -- ---
86 -- vacant -- ---
87 -- vacant -- ---
88 -- vacant -- ---
89 -- vacant -- ---
90 -- vacant -- ---
91 -- vacant -- ---
92 -- vacant -- ---
93 -- vacant -- ---
94 -- vacant -- ---
95 -- vacant -- ---
96 -- vacant -- ---
97 -- vacant -- ---
98 -- vacant -- ---
99 -- vacant -- ---
100 -- vacant -- ---

6-81

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.15 Print Line Item Name Programming

NOTES:
1. The standard program data for the Amount Mark in Item Code 7 is set with a blank after a RAM Clear.
When the specific Amount Mark for the domestic currency is required on sales receipts (such as £, ¥, $), you
must program the entire contents of Item Code 7.
2. The Cashier Symbol to be set in Item Code 8 (“CL” in Standard Program) will be used to print the 2-digit
Cashier ID code on a validation slip. On receipts, the name of each cashier programmed in the CASHIER
NAME AND STATUS PROGRAMMING operation will be printed.
3. If no programming is performed for an item, the name in the Standard Program column will automatically be
active. Therefore, program only the items that require changes from the standard program data.
4. The following are other auto-preset data table and other fixed data table for printing various symbols, items,
or descriptors.

Other Auto-Preset Data (programmable)

The following data are automatically preset in the program memory. However, when the corresponding
items’ names are programmed in the corresponding setting, the programmed name will be active instead of
the preset data.
Item Preset Data Remarks
Department Group GP GP01 to GP15
Department DP DP01 to DP99
Cashier Symbol CL 1CL to 8CL
Salesperson Symbol SP SP01 to SP99

Other Fixed Data (unchangeable)

Item Fixed Data Remarks

RAM Clear RAM-C
Data Clear DATA-C
Status Clear STATUS-C
Program Mode Symbol P
System Option Address #
Percent Rate Symbol %
Non-add Number Symbol #
Taxable Status Mark T
Negative Amount Mark -
Quantity Extension Mark X

6-82

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.16 Display item Name Programming

6.16 Display Item Name Programming

Display Item Name to be displayed on the LCD display can be programmed here. (Max. 16 characters)

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] then [Enter].

or “2 NAMES” is selected.
Depress [2].

Depress the [↓] key seven times then

[Enter] key. “8 DISPLAY ITEM NAME” is selected.
or
Depress [8].

Select a display item name of which

name is to be programmed with the [↑] The display item name already programmed is displayed.
or [↓] key.

[Enter] The ECR enters character input mode.

Input a display item name. A maximum of 16 one-byte or 8 two-byte characters are input.

[Enter] The display item name is entered and printed.

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

NOTES:
1. A maximum of 16 characters can be programmed as the name or message for each Item Code.
2 As shown in the table on the following page, the standard program data is pre-programmed for each Item
Code. (which is auto-set after a RAM Clear). Therefore, program only the name or message that needs to
be changed.

6-83

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.16 Display item Name Programming

Display Item Name Table

Item
Application Standard Program
Code
1 -- vacant --
Signed-OFF condition
2 L O G
(in REG, MGR, or - mode)
3 Balance due after a short tendered T O T A L
4 to 9 -- vacant --
10 Price Shift 1 Operation P R I C E S H I F T 1
11 Price Shift 2 Operation P R I C E S H I F T 2
12 Price Shift 3 Operation P R I C E S H I F T 3
13 to 43 -- vacant --
44 Slip Printer Connection Check S L I P D I S C O N N E C T ?
45 -- vacant --
46 VAT Total V A T . T O T A L
47 Preset Price Open P R O P E N
48 Listing Capacity Open L C O P E N
49 [OPEN] Key Depression O P E N
50 Multiplication X
51 to 53 -- vacant --
54 [TX1/M] Key Depression T X 1 / M
55 [TX2/M] Key Depression T X 2 / M
56 [TX3/M] Key Depression T X 3 / M
57 [TX4/M] Key Depression T X 4 / M
58 [TX5/M] Key Depression T X 5 / M
59 [TX6/M] Key Depression T X 6 / M
60 [TX7/M] Key Depression T X 7 / M
61 [TX8/M] Key Depression T X 8 / M
62 -- vacant --
63 -- vacant --
64 SET, BLIND mode S E T
65 X mode X
66 Z mode Z
67 REG mode R E G
68 MGR mode M G R
69 - mode R E G -
70 Time Setting (hour) h
71 Time Setting (minute) m
72 Item Symbol i t e m
73 -- vacant --
74 -- vacant --
75 Diag. D I A G
76 Key Status Setting (PB-) P B -
77 Key Status Setting (EX) E X
78 Key Status Setting (TRF) T R F
79 YN Symbol Y N
80 Key Status Setting (1’st PRICE) 1 ’ s t P R I C E
81 Key Status Setting (2’nd PRICE) 2 ’ n d P R I C E
82 Key Status Setting (3’rd PRICE) 3 ’ r d P R I C E
83 to 100 -- vacant --

6-84

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.16 Display item Name Programming

3) Example
To program “BALANCE DUE” instead of standard program data “TOTAL” for Item Code 3.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “2 NAMES”.
and in SET mode, depress the [↓] key.

Depress the [2] or [Enter] key. “2 NAMES” is selected.

Depress the [↓] key seven times. The cursor is moved on to

”8 DISPLAY ITEM NAME”.

Depress the [8] or [Enter] key. ”8 DISPLAY ITEM NAME” is selected.

Depress the [↓] key twice, then While ? is shown on the upper-right corner
of the LCD display screen, the [?] key
depress the [Enter] key. depression results in that the following
guidance message appears on the LCD
(Item code 3 (“TOTAL”) is selected.) display.

The [C] key depression clears the The display item name already programmed
is displayed.
display item name already
programmed.

Input a desired name. Numbers of programmed characters and of

programmable characters are displayed on
the 7-segment numeric display.

Example of key operation)

[B] [A] [L] [A] [N] [C] [E] [→] [D] [U] [E]
[Enter]

The [Enter] key depression results in When the [Enter] key is depressed, the
programmed data is printed.
that the input name is entered and
displayed.

(continued on the next page)

6-85

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.16 Display item Name Programming

(continued from the previous page)

Operation LCD Display Remarks

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

DISPLAY NAME
#003 BALANCE DUE

0013 13:31TM

6-86

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.17 Error Item Name Programming

6.17 Error Item Name Programming

Error item names to be displayed on the LCD display are programmed here. A maximum of 16 one-byte
characters by 2 lines can be programmed.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] then [Enter].

or “2 NAMES” is selected.
Depress [2].

Depress the [↓] key eight times then

[Enter] key. “9 ERROR ITEM NAME” is selected.
or
Depress [9].

Select an error code of which error item

name is to be programmed with the [↑] The error item name already programmed is displayed.
or [↓] key.

[Enter] The ECR enters character input mode.

Input an error item name. A maximum of 16 one-byte characters are input.

[Enter] The error item name is entered and printed.

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

NOTES:
1. A maximum of 16 one-byte characters can be programmed as the error item name for each error code.
Enter all the characters in regular size.
2 As shown in the table on the following pages, the standard program data are preprogrammed (which is auto-
set after a RAM Clear). Therefore, program only the error item names that need to be changed.

6-87

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.17 Error Item Name Programming

3) Example
To program “CALL MANAGER” instead of standard program data “MANAGER REQUIRED” for Error Code 3.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “2 NAMES”.
and in SET mode, depress the [↓] key.

Depress the [2] or [Enter] key. “2 NAMES” is selected.

Depress the [↓] key eight times. The cursor is moved on to

”9 ERROR ITEM NAME”.

Depress the [9] or [Enter] key. ”9 ERROR ITEM NAME” is selected.

Depress the [↓] key twice, then While ? is shown on the upper-right corner
of the LCD display screen, the [?] key
depress the [Enter] key. depression results in that the following
guidance message appears on the LCD
(Error Code 3 (“MANAGER display.
REQUIRED”) is selected.)

The [C] key depression clears the error The error item name already programmed is
displayed.
item name already programmed.

Input a desired name. Numbers of programmed characters and of

programmable characters are displayed on
the 7-segment numeric display.

Example of key operation)

[C] [A] [L] [L] [→] [M] [A] [N] [A] [G] [E] [R]
[Enter]

The [Enter] key depression results in When the [Enter] key is depressed, the
programmed data is printed.
that the input name is entered and
displayed.

(continued on the next page)

6-88

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.17 Error Item Name Programming

(continued from the previous page)

Operation LCD Display Remarks

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

ERROR MSG
003 CALL MANAGER

0014 13:33TM

Error Code and Error Item Name Table

Error
Code
Content or Cause of Error Standard Program
1 O P E R A T I O N E R R O R
Operation or Key Sequence Error
2
3 M A N A G E R R E Q U I R E D
Manager Intervention Required
4
5
-- vacant --
6
7 C L O S E D R A W E R
Drawer-Close Compulsory Error
8
9 C O M P U L S O R Y C O D E
Code Entry Compulsory Error
10
11
-- vacant --
12
13
-- vacant --
14
15
-- vacant --
16
17 M I S C E R R O R
Other Miscellaneous Errors
18
19 P C C O M M E R R O R
File Receive Error (with PC feature)
20
21 C O D E E R R O R
Undefined Code or Code Duplicated Error
22
23 P R O G R A M E R R O R
Programming Error
24
25
-- vacant --
26
27
-- vacant --
28
29
-- vacant --
30

6-89

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.17 Error Item Name Programming

Error Code and Error Item Name Table (continued)

Error
Code
Content or Cause of Error Standard Program
31 Limit Over Warning D R A W E R L I M I T
32 (in Media Pick Up)
33
-- vacant --
34
35
-- vacant --
36
37
-- vacant --
38
39
-- vacant --
40
41 C O N S I G N M E N T
Consignment Print Compulsory Error
42 C O M P U L S O R Y
43 C O M P U L S O R Y S L I P
Endorsement Print Compulsory Error
44
45
-- vacant --
46
47
-- vacant --
48
49
-- vacant --
50
51
-- vacant --
52
53
-- vacant --
54
55
-- vacant --
56
57
-- vacant --
58
59
-- vacant --
60
61
-- vacant --
62
63
-- vacant --
64
65 P A P E R E N D
Receipt Printer Paper Out
66 ← R E C E I P T
67 C O V E R O P E N
Receipt Cover Open
68 ← R E C E I P T
69 H E A D O P E N
Journal Paper Retainer Open
70 J O U R N A L →
71 H E A D T E M P E R R O R
Printer Head Temperature Error
72
73 V O L T A G E E R R O R
Printer Head Voltage Error
74
75 P A P E R E N D
Journal Printer Paper Out
76 J O U R N A L →
77
-- vacant --
78
79 S L I P O F F L I N E
Slip printer is offline status.
80

6-90

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.17 Error Item Name Programming

Error Code and Error Item Name Table (continued)

Error
Code
Content or Cause of Error Standard Program
81 Slip Printer Paper Out
S L I P P A P E R O U T
82
83
-- vacant --
84
85
-- vacant --
86
87
-- vacant --
88
89
-- vacant --
90
91
-- vacant --
92
93 S T C O M P
[ST] Key Entry Compulsory error
94
95
-- vacant --
96
97
-- vacant --
98
99
-- vacant --
100
101
-- vacant --
102
103 S A L E S P E R S O N C O M P
Salesperson Entry Compulsory Error
104
105 Salesperson Sign-ON Prohibit Error S A L E S - P P R O H I B I T
106 during a sale
107 T O T A L O N L Y
Total Only Error
108
109 T E N D E R O N L Y
Tender Only Error
110
111 S H _ T E N D P R O H I B I T
Short Tendering Prohibition Error
112
113 O V _ T E N D P R O H I B I T
Over Tendering Prohibition Error
114
115 C A S H I N G P R O H I B I T
No-Sale Exchange Prohibition Error
116
117 Finalization of the R/A entry is F I N R / A P R O H I B I T
118 prohibited.
119
-- vacant --
120
121 N E G A T I V E N U M B E R
Negative Balance Error
122
123
-- vacant --
124
125
-- vacant --
126
127 M D R C O M P
MDR Compulsory Error
128
129 C O N D I T I O N E R R O R
Condition Error
130
131
-- vacant --
132

6-91

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.17 Error Item Name Programming

Error Code and Error Item Name Table (continued)

Error
Code
Content or Cause of Error Standard Program
133
-- vacant --
134
135
-- vacant --
136
137
-- vacant --
138
139
-- vacant --
140
141 P R I C E I N P U T
Price Input Prohibition Error
142 P R O H I B I T E R R O R
143 N O P R I C E I N P U T
No price is input.
144
145 M O D E - C H P R O H I B I T
Key Mode Change Error
146
147
-- vacant --
148
149
-- vacant --
150
151 to
200 -- vacant --

6-92

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.18 Read/Reset Report Name Programming

6.18 Read/Reset Report Name Programming

Read/Reset Report Names are programmed here. A maximum of 12 one-byte characters can be programmed.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] then [Enter].

or “2 NAMES” is selected.
Depress [2].

Depress the [↓] key nine times then

[Enter] key. “0 X/Z REPORT NAME” is selected.
or
Depress [0].

Select an X/Z report No. of which report

name is to be programmed with the [↑] The X/Z report name already programmed is displayed.
or [↓] key.

[Enter] The ECR enters character input mode.

Input an X/Z report name. A maximum of 12 one-byte characters are input.

[Enter] The X/Z report name is entered and printed.

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

NOTES:
1. Enter all characters in regular size. In actually printing on reports, they will be printed in all double-sized
characters.
2. As shown in the table on the following pages, the standard program data is preprogrammed (which is auto-
set after a RAM Clear). Therefore, program only the report names that need to be changed.

6-93

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.18 Read/Reset Report Name Programming

3) Example
To program “X_DP_PROFIT” instead of standard program data “X_PROFIT” for Report No. 21.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “2 NAMES”.
and in SET mode, depress the [↓] key.

Depress the [2] or [Enter] key. “2 NAMES” is selected.

Depress the [↓] key nine times. The cursor is moved on to

”0 X/Z REPORT NAME”.

Depress the [0] or [Enter] key. ” 0 X/Z REPORT NAME” is selected.

Depress the [↓] key twenty times, then While ? is shown on the upper-right corner
of the LCD display screen, the [?] key
depress the [Enter] key. depression results in that the following
guidance message appears on the LCD
(Report No. 21 (“X_PROFIT”) is display.
selected.)

The [C] key depression clears the The report name already programmed is
displayed.
report name already programmed.

Input a desired name. Numbers of programmed characters and of

programmable characters are displayed on
the 7-segment numeric display.

Example of key operation)

[X] 515 [#] [D] [P] 515 [#] [P] [R] [O] [F] [I]
[T] [Enter]

The [Enter] key depression results in When the [Enter] key is depressed, the
programmed data is printed.
that the input name is entered and
displayed.

(continued on the next page)

6-94

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.18 Read/Reset Report Name Programming

(continued from the previous page)

Operation LCD Display Remarks

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

REPORT NAME
#21
X_DP_PROFIT

0015 13:35TM

Read/Reset Report Name Table

X: Daily Read
Z: Daily Reset
GTX: GT Read
GTZ: GT Reset

Report
Report Type Standard Program
No.
1 X X _ F I N A N C I A L
2 Z Z _ F I N A N C I A L
Financial
3 GTX G T X F I N A N C I A L
4 GTZ G T Z F I N A N C I A L
5 X X _ C L E R K
6 Z Z _ C L E R K
All Cashier
7 GTX G T X _ C L E R K
8 GTZ G T Z _ C L E R K
9 X X _ C L E R K
10 Z Z _ C L E R K
Individual Cashier
11 GTX G T X _ C L E R K
12 GTZ G T Z _ C L E R K
13 X X _ S L S P E R S O N
All Salesperson
14 Z Z _ S L S P E R S O N
15
16
17
-- vacant --
18
19
20

6-95

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.18 Read/Reset Report Name Programming

Read/Reset Report Name Table (continued)

X: Daily Read
Z: Daily Reset
GTX: GT Read
GTZ: GT Reset

Report
Report Type Standard Program
No.
21 X X _ P R O F I T
Department Gross Profit
22 GTX G T X _ P R O F I T
23
24 -- vacant --
25
26 X X _ H O U R L Y
Hourly Range
27 Z Z _ H O U R L Y
28 X X _ D P _ A L L
29 Z Z _ D P _ A L L
All Department
30 GTX G T X _ D P _ A L L
31 GTZ G T Z _ D P _ A L L
32
-- vacant --
33
34 All Media Sales and Cash-in Drawer X X _ M E D I A
35 X X _ P L U _ A L L
All PLU
36 Z Z _ P L U _ A L L
37
-- vacant --
38
39 X X _ P L U _ Z O N E
Zone PLU
40 Z Z _ P L U _ Z O N E
41
42
43
44
45
46
47
48
49
50 -- vacant --
51
52
53
54
55
56
57
58
59
60 X X _ M D R
Money Declaration
61 Z Z _ M D R
62
63
64 -- vacant --
65
66

6-96

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.18 Read/Reset Report Name Programming

Read/Reset Report Name Table (continued)

X: Daily Read
Z: Daily Reset
GTX: GT Read
GTZ: GT Reset

Report
Report Type Standard Program
No.
67 Enforced Clear of Hold Condition H O L D _ C A N C E L
68
69
70 -- vacant --
71
72
73 X X _ F I N C A L + D P
74 Z Z _ F I N C A L + D P
Financial + All Department
75 GTX G T X _ F I N C L + D P
76 GTZ G T Z _ F I N C L + D P
77
78
79
80
81
82
83
84
85
86
87
88 -- vacant --
89
90
91
92
93
94
95
96
97
98
99

6-97

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.19 Department Table Programming

6.19 Department Table Programming

For each department, memory opening, and department various statuses settings are performed here.

CONDITION To change the positive/negative status:

After Department and PLU Daily and GT Resets
To change any other programmed data or to newly program departments:
Any time outside a sale
OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode

Depress [↓] twice then [Enter].

or “3 DP/PLU” for Department/PLU table programming is selected.
Depress [3].

Depress [1] or [Enter] key. “1 DP” is selected.

Depress [1] or [Enter] key. “1 DP SETTING” is selected.

Select a department to be programmed with

A department to be programmed is selected.
the [↑] or [↓] key, then depress [Enter].

[Enter] The ECR enters detailed setting mode for department.

Input a Group No. (01 to15), then depress

Department Group No. Setting (See *1.)
[Enter].

Input a preset price, then depress [Enter]. Preset Price Setting (See *2.)

Select a department status with the [↑] or

[↓] key, then depress the [←] or [→] key to Department Status Setting (See *3.)
set/reset the status. After that, depress
[Enter].

Input a VAT/Add-on tax status code (max. 8

VAT/Add-on Tax Status Setting (See *4.)
digits), then depress [Enter].

Input a High Amount Limit (max. 7 digits),

High Amount Limit Setting (See *5.)
then depress [Enter].

Input a Low Amount Limit (max. 7 digits),

Low Amount Limit Setting (See *6.)
then depress [Enter].

Input a Gross Profit Rate (0,01 to 100,00%),

Gross Profit Rate Setting (See *7.)
then depress [Enter].

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

6-98

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.19 Department Table Programming

*1: Department Group No.

• Input a department group code (2 digits: 01 to 15), then depress the [Enter] key.
• To cancel a department group, input 0 then depress the [Enter] key.
• All departments can be programmed in a group. Negative departments are added to the group total.

*2: Preset Price

• For a preset department (preset-price department), enter a maximum of 6-digit price, and depress the
[Enter] key.
1 to 999999 (result: 0,01 to 9999,99)
• A zero-price (0,00) may be preset by entering 0 in the above operation.
• When no numeric value is entered and the [Enter] key is simply depressed, the department will be an
open department (open-price department).

*3: Department Status

• The status ON or OFF is selected with the [←] and [→] keys.
• The status change between positive and negative should be performed after performing a
department/PLU daily and GT resets.
• The following shows each department status.
Status Selective Status
Item
Code ON (Y) OFF (N)
1 Single-item or Itemized Receipt Single-item Itemized
2 -- vacant --
3 Positive or Negative Department Negative Positive
4 -- vacant --
5 -- vacant --
6 -- vacant --
7 -- vacant --
8 -- vacant --

*4: VAT or Add-on Tax Status

Tax type should be selected from either “VAT” or “ADD-ON TAX” by the system option.
• Enter one- to eight-digit status codes for applicable VAT or Add-on Tax.
[Enter]

VAT or Add-on Tax Status Type

0: Non-VAT or Non-taxable
1: VAT 1 or Tax 1
2: VAT 2 or Tax 2
(More than one code can be entered for
3: VAT 3 or Tax 3
combining Tax 1 to Tax 8 taxable statuses.
4: VAT 4 or Tax 4
For example, enter 12 to select VAT 1 and VAT
5: VAT 5 or Tax 5
2 (or Tax 1 and Tax 2) taxable statuses.)
6: VAT 6 or Tax 6
7: VAT 7 or Tax 7
8: VAT 8 or Tax 8
• A combination of VAT and Add-on tax statuses is not possible.

6-99

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.19 Department Table Programming

*5: High Amount Limit

• Enter a maximum of 7 digits to be set as the high amount to be locked out.
Example) To prohibit any amount equal to or larger than 40,00:
4000 [Enter]
(Allows any amount equal to or smaller than 39,99.)
NOTES:
1. To cancel the preset limit (i.e. to allow any amount), input 0.
2. The limit amount set here will be applied to entries in REG mode only, but not in MGR or - mode.
3. Zeros must be entered as all the digits other than the highest digit. If any other value is entered, it will be
regarded as a zero.
Example) Entering 4001 to 4999 will all result in setting 4000.

*6: Low Amount Limit

• Enter a maximum of 7 digits to be set as the low amount limit.
Example) To prohibit any amount smaller than 4,00:
400 [Enter]
(Prohibits any amount smaller than 4,00.)
NOTES:
1. To cancel the preset limit (i.e. to allow any amount), input 0.
2. The limit amount set here will be applied to entries in REG mode only, but not in MGR or - mode.
3. Zeros must be entered as all the digits other than the highest digit. If any other value is entered, it will be
regarded as a zero.
Example) Entering 401 to 499 will all result in setting 400.

*7: Gross Profit Rate

• Enter the gross profit rate of the department in a maximum of 3 integer digits and 2 decimal digits.
[Enter] or [•] [Enter]
0 to 100 (%) 0,01 to 99,99 (%)
• The calculated gross profit will be outputted to the DEPARTMENT GROSS PROFIT REPORT.
• The fraction resulted from the profit calculation will be discarded.
• To cancel the gross profit rate once set, input 0 in place of a specific rate before [Enter]. The
department whose gross profit rate has thus been cancelled will not be outputted in the GROSS PROFIT
REPORT.

3) Example
To program the following Department Data
Department Code: 01
Department Group No.: 01
Preset Price: Open
Department Status: Single-item
Tax Status: VAT 1 and VAT 2
HALO: €40,00
LALO: €4,00
Gross Profit Rate: 10,00%

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “3 DP/PLU”.
and in SET mode, depress the [↓] key
twice.

(continued on the next page)

6-100

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.19 Department Table Programming

(continued from the previous page)

Operation LCD Display Remarks

Depress the [3] or [Enter] key. “3 DP/PLU” is selected.

Depress the [1] or [Enter] key. “1 DP” is selected.

Depress the [1] or [Enter] key. “1 DP SETTINGS” is selected.

Depress the [Enter] key to select The [?] key depression results in that the
following guidance message appears on the
Department 01. LCD display.

*1: see NOTE below

Input 01 (or 1), then depress the The [?] key depression results in that the
following guidance message appears on the
[Enter] key. LCD display.

(Department Group No. 01 is set.)

Depress the [Enter] key. The [?] key depression results in that the
following guidance message appears on the
LCD display.
(The open-price is set.)

The [Enter] key depression allows the The [?] key depression results in that the
following guidance message appears on the
ECR to enter Department Status
LCD display.
setting menu.

(continued on the next page)

6-101

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.19 Department Table Programming

(continued from the previous page)

Operation LCD Display Remarks

Move the cursor on to a desired status The [?] key depression results in that the
following guidance message appears on the
setting with the [↓] or [↑] key. LCD display.

Depress the [→] key then the [Enter] The [→] key depression results in that the
status is changed from N to Y.
key.

(The status of SINGLE-ITEM DP is

selected.)

Input 12, then depress the [Enter] key. The [?] key depression results in that the
following guidance message appears on the
LCD display.
(VAT/Add-on tax statuses 1 and 2 are
set.)

Input 4000, then depress the [Enter] The [?] key depression results in that the
following guidance message appears on the
key. LCD display.

(High amount limit €40,00 is set.)

Input 400, then depress the [Enter] The [?] key depression results in that the
following guidance message appears on the
key. LCD display.

(Low amount limit €4,00 is set.)

Input 10, then depress the [Enter] key. The [?] key depression results in that the
following guidance message appears on the
LCD display.
(Gross Profit Rate 10% is set.)

(continued on the next page)

6-102

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.19 Department Table Programming

(continued from the previous page)

Operation LCD Display Remarks

Depress the [Rtn] key.

The display returns to the Department

Setting screen. Move the cursor on to
another desired department with the
[↓] or [↑] key, then depress the [Enter]
key.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

DP
01 DP01
#01 01
#02
#03 1
#04 12
#05 €40,00
#06 €4,00
#07 10%

0016 13:37TM

NOTE:
(1) Opening the department memory
• After performing a RAM Clear, the department memory on the standard keyboard will be open
automatically.
• On the screen *1, the department can be open by entering a department code and the [Enter] key.

(2) Closing the department memory

• On the screen *1, the department is closed by entering the [Del] key, department code, and the [Enter]
key.
Condition: After Department daily/GT reset, Financial Daily/GT reset, and PLU reset

6-103

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.20 Department Preset Price Setting or Changing

6.20 Department Preset Price Setting or Changing

The preset price of each department may be set in the DEPARTMENT TABLE PROGRAMMING already
described. However, in setting or changing the price only but not other programmed data, the following operation
will be more convenient.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] twice then [Enter].

or “3 DP/PLU” for Department/PLU table programming is selected.
Depress [3].

Depress [1] or [Enter] key. “1 DP” is selected.

Depress [↓] then [Enter].

or “2 UNIT PRICE” is selected.
Depress [2].

Select a department of which unit price

is to be preset with the [↑] or [↓] key.

Input a unit price value. Max. 6 digits (0 to 999999) (See NOTE below.)

[Enter] The department preset price is entered and printed.

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTE: When inputting 0 then depressing the [Enter] key, a zero price will be set to the department. If none of
unit price value is input then the [Enter] key is depressed, the department will be open (i.e. open-price
department).

3) Example
To preset the price €1,00 on Department 1 (FOOD):

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “3 DP/PLU”.
and in SET mode, depress the [↓] key
twice.

(continued on the next page)

6-104

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.20 Department Preset Price Setting or Changing

(continued from the previous page)

Operation LCD Display Remarks

Depress the [3] or [Enter] key. “3 DP/PLU” is selected.

Depress the [1] or [Enter] key. “1 DP” is selected.

Depress the [↓] key. The cursor is moved on to “2 UNIT PRICE”.

Depress the [2] or [Enter] key. “2 UNIT PRICE” is selected.

Input 100 for the preset price of While ? is shown on the upper-right corner
Department 1 (FOOD). of the LCD display screen, the [?] key
depression results in that the following
guidance message appears on the LCD
display.

Depress the [Enter] key. When the [Enter] key is depressed, the
programmed data is printed.

The [End] key depression allows the A long receipt is issued and the display
ECR to end this setting. returns to Main Menu screen.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

DP PRICE
01 FOOD
1,00@

0017 13:39TM

6-105

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.21 Department Listing Capacity (LC) Programming

6.21 Department Listing Capacity (LC) Programming

The High Amount to be Locked Out (HALO) and Low Amount to be Locked Out (LALO) relating to the
department entry are programmed here. Entry of an amount larger than HALO or smaller than LALO can be
prohibited.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] twice then [Enter].

or “3 DP/PLU” for Department/PLU table programming is selected.
Depress [3].

Depress [1] or [Enter] key. “1 DP” is selected.

Depress [↓] twice then [Enter].

or “3 DIGIT LIMIT(PRICE)” is selected.
Depress [3].

Input a HALO value. Max. 7 digits (0 to 9999999)

[Enter]

Input a LALO value. Max. 7 digits (0 to 9999999)

[Enter] HALO and LALO are entered and printed.

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

NOTES:
1. HALO and LALO relating to the department entry are programmed as shown below. (Max. 7 digits)
• Input a HALO value or LALO value relating to the department entry, then depress the [Enter] key.
XXXXXXX [Enter]
(HALO or LALO)
• Amount limit at the department entry: HALO > Department preset price ≧ LALO
• Example of HALO programming
To prohibit an entry of an amount larger than 4000, input 4000.
(i.e. The amount equal to or smaller than 3999 can be entered.)
Example of LALO programming
To allow an entry of an amount equal to or larger than 40, input 40.

6-106

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.21 Department Listing Capacity (LC) Programming

• The HALO and LALO programmed here are effective at the department entry in REG mode only. They
are not effective in MGR and - mode, as a maximum of 7-digit amount value can be entered.
• Zeros must be entered as all the digits other than the highest digit. If any other value is entered, it will be
regarded as a zero.
Example) Entering 4001 to 4999 will all result in setting 4000.
2. Regarding a department of which amount limit is individually preprogrammed, the HALO and LALO
programmed here will be ignored.
3. The HALO and LALO programmed here are cancelled at the department entry by depressing the [LC
OPEN] or [OPEN] key. (i.e. Amounts of 2-digit more than HALO and of 1-digit less than LALO can be
entered, up to a maximum of 7 digits.)
A maximum of 7-digit amount value can be entered in MGR and - mode.

3) Example
To program 100000 for HALO and 10 for LALO.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “3 DP/PLU”.
and in SET mode, depress the [↓] key
twice.

Depress the [3] or [Enter] key. “3 DP/PLU” is selected.

Depress the [1] or [Enter] key. ”1 DP” is selected.

Depress the [↓] key twice. The cursor is moved on to “3 DIGIT LIMIT
(PRICE)”.

Depress the [3] or [Enter] key. “3 DIGIT LIMIT (PRICE)” is selected.

Input 100000, then depress the [Enter] While ? is shown on the upper-right corner
key. of the LCD display screen, the [?] key
depression results in that the following
guidance message appears on the LCD
(HALO: 100000) display.

(continued on the next page)

6-107

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.21 Department Listing Capacity (LC) Programming

(continued from the previous page)

Operation LCD Display Remarks

Input 10, then depress the [Enter] key. When the [Enter] key is depressed, the
programmed data is printed.
(LALO: 10)

The [End] key depression allows the A long receipt is issued and the display
ECR to end this programming. returns to Main Menu screen.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

AMOUNT LIMIT
#01 €1000,00
#02 €0,10

0018 13:41TM

6-108

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.22 Key Sticker Printing

6.22 Key Sticker Printing

Key stickers of department names which were programmed in the DEPARTMENT NAME PROGRAMMING can
be printed on the receipt printer.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart
• For printing all department names

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] twice then [Enter].

“3 DP/PLU” for Department/PLU table programming is selected.
or Depress [3].

Depress [1] or [Enter] key. “1 DP” is selected.

Depress [↓] three times then [Enter].

“4 KEY STICKER PRINT” is selected.
or Depress [4].

Depress [1] or [Enter] key. The names of departments 1 to 15 are printed.

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

• For printing part of department names

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] twice then [Enter].

“3 DP/PLU” for Department/PLU table programming is selected.
or Depress [3].

Depress [1] or [Enter] key. “1 DP” is selected.

Depress [↓] three times then [Enter].

“4 KEY STICKER PRINT” is selected.
or Depress [4].

Depress [↓] then [Enter].

“2 INDIVIDUAL DP” is selected.
or Depress [2].

Select desired departments with [↑] or The names of departments selected are printed.
[↓] key, then depress [Enter] key.

This operation is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

6-109

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.22 Key Sticker Printing

NOTES:
1. Print format
< Single key >
• For the single key, a maximum of 12-digit department name (6 characters x 2 lines) can be printed.
• For a 7-digit-or-more department name, the first 6 digits are printed in the first line and the 7th digit and
after are printed in the second line.
• The 6-digit-or-less department name is printed in the second line.
• For a 13-digit-or-more department name, the first 12 digits are printed.
< Double-width key >
• For the double-width key, a maximum of 16-digit department name can be printed.
• The department name is printed in the second line.
2. Departments 1 through 5 are fixed to the double-width keys and Departments 6 through 15 are fixed to the
single keys. The number of the department is fixed to 15, as it remains unchanged even when the number
of the department keys are changed in the SFKC PROGRAMMING.
3. Key sticker printing should not be performed when the flat type keyboard is provided. (i.e. none of key caps
are provided.)
4. The key sticker is printed on the receipt only. Only the header is printed on the journal.
5. When a department name contains two-byte characters, it will be printed with all one-byte characters.

3) Example
(1) To print all department names.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “3 DP/PLU”.
and in SET mode, depress the [↓] key
twice.

Depress the [3] or [Enter] key. “3 DP/PLU” is selected.

Depress the [1] or [Enter] key. ”1 DP” is selected.

Depress the [↓] key three times. The cursor is moved on to “4 KEY STICKER
PRINT”.

Depress the [4] or [Enter] key. “4 KEY STICKER PRINT” is selected.

(continued on the next page)

6-110

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.22 Key Sticker Printing

(continued from the previous page)

Operation LCD Display Remarks

Depress the [1] or [Enter] key. ”1 ALL DP” is selected.

A confirmation message is displayed.

The [End] key depression allows the A long receipt is issued and the display
ECR to end this operation. returns to Main Menu screen.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

0019 13:43TM

6-111

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.22 Key Sticker Printing

(2) To print part of department names.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “3 DP/PLU”.
and in SET mode, depress the [↓] key
twice.

Depress the [3] or [Enter] key. “3 DP/PLU” is selected.

Depress the [1] or [Enter] key. ”1 DP” is selected.

Depress the [↓] key three times. The cursor is moved on to “4 KEY STICKER
PRINT”.

Depress the [4] or [Enter] key. “4 KEY STICKER PRINT” is selected.

Depress the [↓] key. The cursor is moved on to “2 INDIVIDUAL

DP”.

Depress the [2] or [Enter] key. ”2 INDIVIDUAL DP” is selected

The department name already While ? is shown on the upper-right corner

programmed is displayed. of the LCD display screen, the [?] key
depression results in that the following
guidance message appears on the LCD
Move the cursor on to a desired display.
department name of which key sticker
is to be printed with the [↓] or [↑] key,
then depress the [Enter] key.

The [End] key depression allows the A long receipt is issued and the display
ECR to end this operation. returns to Main Menu screen.

6-112

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.23 PLU Table Programming

6.23 PLU Table Programming

This programming can be operated when new PLU items are to be added, PLU program data is to be changed,
or PLUs are to be deleted.

6.23.1 Programming or Changing

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] twice then [Enter].

or “3 DP/PLU” for Department/PLU table programming is selected.
Depress [3].

Depress [↓] then [Enter].

or “2 PLU” is selected.
Depress [2].

Depress [1] or [Enter] key. “1 PLU SETTING” is selected.

Input a PLU Code. Max. 4 digits: 1 to 9999

[PLU] The ECR enters detailed setting mode for PLU.

Input a linked department code (01 to 40),

Link Department No. Setting (See *1.)
then depress [Enter].

Input a preset price (max. 6 digits: 1 to

999999), then depress [Enter]. Preset Price Setting (See *2.)
(result: 0,01 to 9999,99)

Input a 2nd preset price (max. 6 digits: 1 to

999999), then depress [Enter]. 2nd Preset Price Setting (See *3.)
(result: 0,01 to 9999,99)

Input a 3rd preset price (max. 6 digits: 1 to

999999), then depress [Enter]. 3rd Preset Price Setting (See *4.)
(result: 0,01 to 9999,99)

Input a VAT/Add-on tax status code (max. 8

VAT/Add-on Tax Status Setting (See *5.)
digits), then depress [Enter].

The next PLU code (i.e. the currently programmed PLU code plus
[PLU] 1) is displayed.

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

6-113

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.23 PLU Table Programming

NOTES:
1. A maximum of 1,000 PLUs are programmable.
2 If a PLU is linked to a negative department, the PLU is automatically set as negative PLU.
3. The [PLU] key here indicates the key labelled simply as “PLU” but not any PLU preset-code keys.

*1: Linked Department Code

• Enter a 2-digit code of the department to which the PLU is linked.
When the PLU is newly programmed, this entry is compulsory (an error will result if this entry is skipped.)
[Enter]
01 to 40

*2: Preset Price

• For a preset PLU (preset-price PLU), enter a maximum of 6-digit price, and depress the [Enter] key.
1 to 999999 (result: 0,01 to 9999,99)
• A zero-price (0,00) may be preset by entering 0 in the above operation.
• When no numeric value is entered and the [Enter] key is simply depressed, the PLU will be an open PLU
(open-price PLU).

*3: 2nd Preset Price

• For a preset PLU (preset-price PLU), enter a maximum of 6-digit price, and depress the [Enter] key.
1 to 999999 (result: 0,01 to 9999,99)
• A zero-price (0,00) may be preset by entering 0 in the above operation.
• If the 2nd preset price entry is skipped, the 1st preset price will be automatically programmed as the 2nd
preset price.

*4: 3rd Preset Price

• For a preset PLU (preset-price PLU), enter a maximum of 6-digit price, and depress the [Enter] key.
1 to 999999 (result: 0,01 to 9999,99)
• A zero-price (0,00) may be preset by entering 0 in the above operation.
• If the 3rd preset price entry is skipped, the 1st preset price will be automatically programmed as the 3rd
preset price.

*5: VAT or Add-on Tax Status

Tax type should be selected from either “VAT” or “ADD-ON TAX” by the system option.
• Enter one- to eight-digit status codes for applicable VAT or Add-on Tax.
[Enter]

VAT or Add-on Tax Status Type

0: Non-VAT or Non-taxable
1: VAT 1 or Tax 1
2: VAT 2 or Tax 2
(More than one code can be entered for
3: VAT 3 or Tax 3 combining Tax 1 to Tax 8 taxable statuses.
4: VAT 4 or Tax 4 For example, enter 12 to select VAT 1 and VAT
5: VAT 5 or Tax 5 2 (or Tax 1 and Tax 2) taxable statuses.)
6: VAT 6 or Tax 6
7: VAT 7 or Tax 7
8: VAT 8 or Tax 8

• A combination of VAT and Add-on tax statuses is not possible.

6-114

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.23 PLU Table Programming

3) Example
To program the following PLU data:
PLU Code: 0010
Linked Department: Department 1
Preset Price: €1,00
2nd Preset Price: €1,20
3rd Preset Price: €1,50
Tax Status: 12 (VAT 1 and VAT 2)

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “3 DP/PLU”.
and in SET mode, depress the [↓] key
twice.

Depress the [3] or [Enter] key. “3 DP/PLU” is selected.

Depress the [↓] key. The cursor is moved on to “2 PLU”.

Depress the [2] or [Enter] key. “2 PLU” is selected.

Depress the [1] or [Enter] key. “1 PLU SETTING” is selected.

Input 0010 (or 10), then depress the PLU Code: Max. 4 digits (1 to 9999)
[PLU] key.

(PLU Code 0010 is set.)

Input 01 (or 1), then depress the The [?] key depression results in that the
following guidance message appears on the
[Enter] key. LCD display.

(Linked Department 1 is set.)

(continued on the next page)

6-115

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.23 PLU Table Programming

(continued from the previous page)

Operation LCD Display Remarks

Input 100, then depress the [Enter] The [?] key depression results in that the
following guidance message appears on the
key. LCD display.

(Preset Price €1,00 is set.)

Input 120, then depress the [Enter] The [?] key depression results in that the
following guidance message appears on the
key. LCD display.

(2nd Preset Price €1,20 is set.)

Input 150, then depress the [Enter] The [?] key depression results in that the
following guidance message appears on the
key. LCD display.

(3rd Preset Price €1,50 is set.)

Input 12, then depress the [Enter] key. The [?] key depression results in that the
following guidance message appears on the
LCD display.
(VAT statuses 1 and 2 are set.)

The [PLU] key depression completes When the [PLU] key is depressed, the next
the programming for PLU code 0010. PLU code (i.e. the currently programmed
PLU code plus 1) is displayed here.
(Addition of new PLUs and changes of
current PLUs can be performed.)

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

31-10-2005 MON #0

PLU
0010 PLU0010
#01 01
#02 1,00@
#03 1,20@
#04 1,50@
#05 12

0001

0020 13:45TM
6-116

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.23 PLU Table Programming

6.23.2 Deletion
CONDITION To delete a PLU with sales data of zero: Any time outside a sale
To delete a PLU with sales data of not zero: After PLU Reset

OPERATION Mode Lock: SET

Individual PLU Deletion: The programmed PLU data is deleted individually.

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] twice then [Enter].

or “3 DP/PLU” for Department/PLU table programming is selected.
Depress [3].

Depress [↓] then [Enter].

or “2 PLU” is selected.
Depress [2].

Depress [↓] three times then [Enter].

or “4 DELETE (INDIV)” is selected.
Depress [4].

Input a PLU code to be deleted. Max. 4 digits: 1 to 9999

[PLU] The specified PLU is deleted.

This operation is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

3) Example
To delete PLU Code 0501 (Tuna Can) that was once programmed.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “3 DP/PLU”.
and in SET mode, depress the [↓] key
twice.

Depress the [3] or [Enter] key.

(continued on the next page)

6-117

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.23 PLU Table Programming

(continued from the previous page)

Operation LCD Display Remarks

Depress the [↓] key.

Depress the [1] or [Enter] key. “2 PLU” is selected.

Depress the [↓] key three times. The cursor is moved on to “4 DELETE
(INDIV)”.

Depress the [4] or [Enter] key. “4 DELETE (INDIV)” is selected.

Input 0501 (or 501), then depress the PLU Code: Max. 4 digits (1 to 9999)
[PLU] key.

(PLU Code 0501 is specified.)

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this operation.

6-118

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.23 PLU Table Programming

All PLU Deletion: The programmed PLU data is deleted entirely.

1) Menu Tree

2) Operation
Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “3 DP/PLU”.
and in SET mode, depress the [↓] key
twice.

Depress the [3] or [Enter] key.

Depress the [↓] key.

Depress the [2] or [Enter] key. “2 PLU” is selected.

Depress the [↓] key four times. The cursor is moved on to “5 DELETE
(ALL)”.

Depress the [5] or [Enter] key. “5 DELETE (ALL)” is selected.

Depress the [ALL VOID] key. The entire programmed PLU data is deleted,
then the following message is displayed.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this operation.

6-119

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.24 PLU Preset Price Setting or Changing

6.24 PLU Preset Price Setting or Changing

The preset price of each PLU may be set in the PLU TABLE PROGRAMMING already described. However, in
setting or changing the price only (not other programmed data), the following operation will be more convenient.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] twice then [Enter].

or “3 DP/PLU” for Department/PLU table programming is selected.
Depress [3].

Depress [↓] then [Enter].

or “2 PLU” is selected.
Depress [2].

Depress [↓] then [Enter].

or “2 UNIT PRICE” is selected.
Depress [2].

Input a PLU code of which PLU preset

PLU code: Max. 4 digits (1 to 9999)
price is to be set or changed.

[PLU]

Input 1st preset price, then [Enter]. Max. 6 digits (0 to 999999) (NOTE1)

Input 2nd preset price, then [Enter]. Max. 6 digits (0 to 999999) (NOTE1)

Input 3rd preset price, then [Enter]. Max. 6 digits (0 to 999999) (NOTE1)

[PLU] The preset prices are entered and printed. (NOTE3)

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

6-120

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.24 PLU Preset Price Setting or Changing

NOTES:
1. When no price is input then the [Enter] key is depressed, the PLU will be open (i.e. open-price PLU).
2. If inputting a nonexistent PLU code that was not programmed in the PLU Table Programming, this may
cause an error.
3. The [PLU] key depression here results in that the next PLU code (i.e. the currently programmed PLU code
plus 1) is displayed. If it does not exist, the guidance message requiring a PLU code input is displayed.

3) Example
To change the preset prices of PLU Code 0001 as shown below:
PLU Code: 0001
1st Preset Price: It is changed from €1,05 to €3,15.
2nd Preset Price: It is changed from €2,10 to €5,40.
3rd Preset Price: It remains €3,20.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “3 DP/PLU”.
and in SET mode, depress the [↓] key
twice.

Depress the [3] or [Enter] key.

Depress the [↓] key. The cursor is moved on to “2 PLU”.

Depress the [2] or [Enter] key.

Depress the [↓] key. The cursor is moved on to “2 UNIT PRICE”.

Depress the [2] or [Enter] key.

Input 1, then depress the [PLU] key. PLU Code 0001 is specified.

(continued on the next page)

6-121

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.24 PLU Preset Price Setting or Changing

(continued from the previous page)

Operation LCD Display Remarks

Make sure the cursor is shown on The 1st preset price is changed from €1,05
to €3,15.
01PRICE. Then, input 315 and
depress the [Enter] key. While ? is shown on the upper-right corner
of the LCD display screen, the [?] key
depression results in that the following
guidance message appears on the LCD
display.

Make sure the cursor is shown on The 2nd preset price is changed from €2,10
to €5,40.
022ND PRICE. Then, input 540 and
depress the [Enter] key.

As the 3rd preset price remains PLU0001 preset price setting is ended.
unchanged, depress the [PLU] key.
When the [Enter] key is depressed, the
programmed data is printed.

After the [PLU] key depression The next PLU code (i.e. the currently
programmed PLU code plus 1) is displayed.

If the next PLU code (i.e. the currently

programmed PLU code plus 1) does not
exist, this guidance message requiring a PLU
code input is displayed.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this programming.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

PLU PRICE
0001 PLU0001
#01 3,15@
#02 5,40@
#03 3,20@

0021 13:47TM

6-122

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.25 PLU Preset-Code Key Setting

6.25 PLU Preset-Code Key Setting

When there are any keys programmed as PLU Preset-code Keys (SFKC 96) on the ECR Keyboard (ordinary or
Flat type), and /or when the PK-2 PLU Keyboard (hardware option) is connected to the ECR, a PLU code may be
preset to each of those keys in this operation.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart
• For PLU Preset-Code Key (SFKC 96)

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] twice then [Enter].

or “3 DP/PLU” is selected.
Depress [3].

Depress [↓] then [Enter].

or “2 PLU” is selected.
Depress [2]

Depress [↓] twice then [Enter].

or “3 ASSIGN TO KEYBOARD” is selected.
Depress [3].

Depress [↓] then [Enter].

or “2 PLU CODE KEY” is selected.
Depress [2]

Input a PLU Code. A 4-digit PLU code to be assigned to a key is specified.

[Enter]

Input a desired key location code. See Key Location Code on the next page.

[Enter]

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

6-123

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.25 PLU Preset-Code Key Setting

• For PK-2 Keyboard

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] twice then [Enter].

or “3 DP/PLU” is selected.
Depress [3].

Depress [↓] then [Enter].

or “2 PLU” is selected.
Depress [2]

Depress [↓] twice then [Enter].

or “3 ASSIGN TO KEYBOARD” is selected.
Depress [3].

Depress [Enter].
or “1 PK-2” is selected.
Depress [1]

Input a PLU Code. A 4-digit PLU code to be assigned to a key is specified.

[Enter]

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTE: PLU Codes 1 through 130 are automatically assigned to the PK-2 after performing a RAM Clear.

Key Location Code

• Ordinary type keyboard

1 7 13 19 25 31 37 43 49 55 61

2 8 14 20 26 32 38 44 50 56 62

3 9 15 21 27 33 39 45 51 57 63

4 10 16 22 28 34 40 46 52 58 64

5 11 17 23 29 35 41 47 53 59 65

6 12 18 24 30 36 42 48 54 60 66

* For the double-width key, the key location code on the right is effective.

6-124

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.25 PLU Preset-Code Key Setting

• Flat type keyboard

1 8 15 22 29 36 43 50 57 64 71 77 83 90 97 100

2 9 16 23 30 37 44 51 58 65 72 78 84 91 98 101

3 10 17 24 31 38 45 52 59 66 73 85 92 99 102

4 11 18 25 32 39 46 53 60 67 74 79 86 93 103

5 12 19 26 33 40 47 54 61 68 75 80 87 94 104

6 13 20 27 34 41 48 55 62 69 81 88 95 105
76
7 14 21 28 35 42 49 56 63 70 82 89 96 106

3) Example
(1) To assign PLU Code 1111 to Key Location Code 55 on the ordinary type keyboard.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “3 DP/PLU”.
and in SET mode, depress the [↓] key
twice.

Depress the [3] or [Enter] key. “3 DP/PLU” is selected.

Depress the [↓] key. The cursor is moved on to “2 PLU”.

Depress the [2] or [Enter] key. “2 PLU” is selected.

Depress the [↓] key twice. The cursor is moved on to “3 ASSIGN TO

KEYBOARD”.

Depress the [3] or [Enter] key. “3 ASSIGN TO KEYBOARD” is selected.

(continued on the next page)

6-125

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.25 PLU Preset-Code Key Setting

(continued from the previous page)

Operation LCD Display Remarks

Depress the [↓] key. The cursor is moved on to “2 PLU CODE

KEY”.

Depress the [2] or [Enter] key. “2 PLU CODE KEY” is selected.

Input 55, then depress the [Enter] key. On this screen, when inputting a PLU code
then depressing a PLU preset-code key, the
[PLU] key setting is possible. In this case,
(Key Location Code 55 is set.) the PLU preset-code keys on the standard
flat type keyboard can be set. The other
keys should be set with the key location
code.

Input 1111, then depress the [Enter]

key.

(PLU Code 1111 is set.)

The display returns to the key location

code input screen.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this setting.

(2) To assign PLU Code 1111 on the PK-2 keyboard.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “3 DP/PLU”.
and in SET mode, depress the [↓] key
twice.

Depress the [3] or [Enter] key. “3 DP/PLU” is selected.

(continued on the next page)

6-126

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.25 PLU Preset-Code Key Setting

(continued from the previous page)

Operation LCD Display Remarks

Depress the [↓] key. The cursor is moved on to “2 PLU”.

Depress the [2] or [Enter] key. “2 PLU” is selected.

Depress the [↓] key twice. The cursor is moved on to “3 ASSIGN TO

KEYBOARD”.

Depress the [3] or [Enter] key. “3 ASSIGN TO KEYBOARD” is selected.

Depress the [1] or [Enter] key. “1 PK-2” is selected.

Input 1111, then depress the [Enter]

key.

(PLU Code 1111 is set.)

Directly depress a key on the PK-2

keyboard where PLU Code 1111 is to
be assigned.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this setting.

6-127

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.26 %+ and %- Preset Rate Setting

6.26 %+ and %- Preset Rate Setting

A preset rate may be set on each of the [%+] and [%-] keys, one independent rate for each key. Once a rate is
preset, the % key will simply be depressed without a prior rate entry to activate the preset rate. If a rate is
entered prior to the depression of the key, the entered rate (manual rate) will be activated instead.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] three times then [Enter].

or “4 RATE, LIMIT AMOUNT” is selected.
Depress [4].

Depress the [1] or [Enter] key. “1 %- RATE (%-/%+)” is selected.

Select a [%] key to be programmed To select [%-] key, depress [1] or [Enter].
with the [↓] key. To select [%+] key, depress [2] or depress [↓] then [Enter].

[Enter]

0,001 to 99,999 (%): Use the [.] key if decimal portion is contained.
Input a Preset Rate. (See NOTE below.)

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTE: When inputting 0, the % preset rate will be cancelled. If doing so, the % preset rate should be set in the
registration operation.

6-128

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.26 %+ and %- Preset Rate Setting

3) Example
To program the following rate on the [%-] key:
[%-] key ………. Rate 5,00%

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “4 RATE, LIMIT
AMOUNT”.
and in SET mode, depress the [↓] key
three times.

Depress the [4] or [Enter] key. “4 RATE, LIMIT AMOUNT” is selected.

Depress the [1] or [Enter] key. “1 %- RATE (%-/%+)” is selected.

Depress the [1] or [Enter] key. “1 %-” is selected.

Input 5. Preset Rate 5,00% is entered.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this setting.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

% RATE
%- 5%

0022 13:49TM

6-129

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.27 VAT or Add-on Tax Rate Setting

6.27 VAT or Add-on Tax Rate Setting

The rates of VATs or Add-on Taxes are set in this operation,. (Which VAT or Add-on Tax is applicable to each
Department or PLU has already been set in the DEPARTMENT TABLE PROGRAMMING and PLU TABLE
PROGRAMMING.)

CONDITION After Financial Daily Reset

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] three times then [Enter].

or “4 RATE, LIMIT AMOUNT” is selected.
Depress [4].

Depress the [↓] then [Enter]

or “2 VAT/TAX RATE” is selected.
Depress [2].

Input a rate of VAT1 or TAX1, then 0,01 to 99,99 (%): Use the [.] key if decimal portion is contained.
depress the [Enter] key.

Input a rate of VAT2 or TAX2, then

0,01 to 99,99 (%): Use the [.] key if decimal portion is contained.
depress the [Enter] key.

Input a rate of VAT3 or TAX3, then

0,01 to 99,99 (%): Use the [.] key if decimal portion is contained.
depress the [Enter] key.

Input a rate of VAT4 or TAX4, then 0,01 to 99,99 (%): Use the [.] key if decimal portion is contained.
depress the [Enter] key.

Input a rate of VAT5 or TAX5, then

0,01 to 99,99 (%): Use the [.] key if decimal portion is contained.
depress the [Enter] key.

Input a rate of VAT6 or TAX6, then

0,01 to 99,99 (%): Use the [.] key if decimal portion is contained.
depress the [Enter] key.

Input a rate of VAT7 or TAX7, then 0,01 to 99,99 (%): Use the [.] key if decimal portion is contained.
depress the [Enter] key.

Input a rate of VAT8 or TAX8, then

0,01 to 99,99 (%): Use the [.] key if decimal portion is contained.
depress the [Enter] key.

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTE: Either VAT or Add-on Tax can be used. Tax feature is according to the status selected in Address No.
21, Bit No. 5 of the system option.

6-130

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.27 VAT or Add-on Tax Rate Setting

3) Example
To set the following VAT rate:
VAT1………10%

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “4 RATE, LIMIT
AMOUNT”.
and in SET mode, depress the [↓] key
three times.

Depress the [4] or [Enter] key. “4 RATE, LIMIT AMOUNT” is selected.

Depress the [↓] key The cursor is moved on to “2 VAT/TAX

RATE”.

Depress the [2] or [Enter] key. “2 VAT/TAX RATE” is selected.

Input 10, then depress the [Enter] key. While ? is shown on the upper-right corner
of the LCD display screen, the [?] key
depression results in that the following
guidance message appears on the LCD
display.

Depress the [↓] six times.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this setting.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

VAT/TAX RATE
VAT1 10%

6-131 0023 13:51TM

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.28 Foreign Currency Exchange Rate Setting

6.28 Foreign Currency Exchange Rate Setting

The rate of each foreign currency (corresponding to the [CUR1] to [CUR5] keys) are set in this operation.
By setting a rate on each Foreign Currency Key, reading the sale total and tendering in the foreign currency value
will be possible for sale finalization.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode

Depress [↓] three times then [Enter].

or “4 RATE, LIMIT AMOUNT” is selected.
Depress [4].

Depress [↓] twice then [Enter].

or “3 CUR EXCHANGE RATE” is selected.
Depress [3].

Input the rate of [CUR1] key, then 0,000001 to 9999,999999 (%): Use the [.] key if decimal portion is
depress [Enter]. contained. (See NOTE below.)

Input the rate of [CUR2] key, then 0,000001 to 9999,999999 (%): Use the [.] key if decimal portion is
depress [Enter]. contained. (See NOTE below.)

Input the rate of [CUR3] key, then 0,000001 to 9999,999999 (%): Use the [.] key if decimal portion is
depress [Enter]. contained. (See NOTE below.)

Input the rate of [CUR4] key, then 0,000001 to 9999,999999 (%): Use the [.] key if decimal portion is
depress [Enter]. contained. (See NOTE below.)

Input the rate of [CUR5] key, then 0,000001 to 9999,999999 (%): Use the [.] key if decimal portion is
depress [Enter]. contained. (See NOTE below.)

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTE: When inputting 0, the rate of the foreign currency will be cancelled. If doing so, the rate of the foreign
currency should be set in the registration operation.

6-132

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.28 Foreign Currency Exchange Rate Setting

Foreign Currency Exchange Rate Calculation

1. The rate must be calculated in the subsidiary currency unit values for both the domestic and the foreign
currencies. (In case of calculating the rate from the domestic to a foreign currency with the same zero-
suppress form, such as from Euro to U.S. $, it will be no problem even if it is calculated in the main currency
of Euro and $. However, in case of exchanging from a domestic currency such as Euro or $ to Japanese
yen, or vice versa, this rule must be obeyed; otherwise a wrong rate will result.)
2. Calculate the required foreign currency value equivalent to the domestic currency value “1”. Then the
obtained value is the Exchange Rate value to be entered in the setting operation stated on the previous
page.

3) Example
To set two foreign currency rates:
(The rates here are merely examples, and may be different from the actual rates currently in effect.)

Conditions given for Domestic Currency and Foreign Currencies

(DOMESTIC) (CUR1) (CUR2)

EURO U.S. Dollar Japanese Yen

€1,00 $1,20 ¥137,74

1 EURO Cent 1.20 Cent 1,3774 yen

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “4 RATE, LIMIT
AMOUNT”.
and in SET mode, depress the [↓] key
three times.

Depress the [4] or [Enter] key. “4 RATE, LIMIT AMOUNT” is selected.

Depress the [↓] key twice. The cursor is moved on to “3 CUR

EXCHANGE RATE”.

Depress the [3] or [Enter] key. “3 CUR EXCHANGE RATE” is selected.

(continued on the next page)

6-133

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.28 Foreign Currency Exchange Rate Setting

(continued from the previous page)

Operation LCD Display Remarks

Make sure the cursor is shown on The exchange rate from € to $ is set on the
[CUR1] key.
01CUR1. Then, input 1.20 and
depress the [Enter] key. While ? is shown on the upper-right corner
of the LCD display screen, the [?] key
depression results in that the following
guidance message appears on the LCD
display.

Make sure the cursor is shown on The exchange rate from € to Japan Yen is
set on the [CUR2] key.
02CUR2. Then, input 1.3774 and
depress the [Enter] key.

Depress the [↓] key twice. The cursor is moved on to “05CUR5”.

Make sure the cursor is shown on

05CUR5.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this setting.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

CUR RATE
CUR1 1.2∗
CUR2 1,3774∗

0024 13:53TM

Resetting a Foreign Currency Rate Once Set

Input 0 in place of the Exchange Rate for the Foreign Currency in the setting operation. Then the rate for that
foreign currency will be reset. The rate of the Foreign Currency Key thus reset cannot be used in sales entries.

6-134

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.29 Negative Amount Key Limit Amount Setting

6.29 Negative Amount Key Limit Amount Setting

The limit amount to be entered through each of the negative-amount keys [VND CPN], [STR CPN], and [-] Are
set here.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] three times then [Enter].

or “4 RATE, LIMIT AMOUNT” is selected.
Depress [4].

Depress [↓] three times then [Enter].

or “4 DISC AMT LIMIT” is selected.
Depress [4].

Input the limit amount of the Vender

Coupon Key ([VND CPN]), then 0 to 999999 (€0,00 to €9999,99)
depress [Enter].

Input the limit amount of the Store

Coupon Key ([STR CPN]), then 0 to 999999 (€0,00 to €9999,99)
depress [Enter].

Input the limit amount of the Amount

Discount Key ([-]), then depress 0 to 999999 (€0,00 to €9999,99)
[Enter].

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTES: 1. The [VND CPN] key will not be restricted by the limit amount set here but the amount up to 7
digits will be entered in MGR or - mode.
2. The limit amount set here cannot be released by the [LC OPEN] (or [OPEN]) key in transaction
entries.

6-135

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.29 Negative Amount Key Limit Amount Setting

3) Example
To set the following preset amount on the keys below:
Key Limit Amount
[VND CPN] 10.00
[STR CPN] 20.00

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “4 RATE, LIMIT
and in SET mode, depress the [↓] key AMOUNT”.
three times.

Depress the [4] or [Enter] key. “4 RATE, LIMIT AMOUNT” is selected.

Depress the [↓] key three times. The cursor is moved on to “4 DISC AMT
LIMIT”.

Depress the [4] or [Enter] key. “4 DISC AMT LIMIT” is selected.

Input 1000, then depress the [Enter] While ? is shown on the upper-right corner
key. of the LCD display screen, the [?] key
depression results in that the following
guidance message appears on the LCD
(The limit amount of the [VND CPN] display.
key is set.)

Input 2000, then depress the [Enter]

key.

(The limit amount of the [STR CPN]

key is set.)

The [End] key depression allows the A long receipt is issued and the display
ECR to end this setting. returns to Main Menu screen.

31-10-2005 MON #0

LIMIT TABLE
V.CPN €10,00
S.CPN €20,00

0025 13:55TM

6-136

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.30 Time Setting or Adjustment

6.30 Time Setting or Adjustment

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] four times then [Enter].

or “5 BASIC” is selected.
Depress [5].

Depress [1] or [Enter]. “1 TIME” is selected.

Input a 4-digit time value. 4-digiti-time value (HHMM) (See NOTE below.)

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTE: If an hour value of more than 23 or a minute value of more than 59 is entered, the current data remains
unchanged by setting or adjusting the time.

3) Example
To set time “1:15 p.m. (13:15)”

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “5 BASIC”.
and in SET mode, depress the [↓] key
four times.

Depress the [5] or [Enter] key. “5 BASIC” is selected.

Depress the [1] or [Enter] key. “1 TIME” is selected.

(continued on the next page)

6-137

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.31 Date Setting or Adjustment

(continued from the previous page)

Operation LCD Display Remarks

Input 1315. The time “13:15” is set.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this setting.

31-10-2005 MON #0

TIME
13:15TM

0026 13:15TM

6.31 Date Setting or Adjustment

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] four times then [Enter].

or “5 BASIC” is selected.
Depress [5].

Depress [↓] then [Enter].

or “2 DATE” is selected.
Depress [2].

Input a 9-digit value. 9-digit value (Day-of-Week Code & DDMMYYYY)

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTE: The date entry order may be Month-Day-Year or Year-Month-Day instead of Day-Month-Year if so
selected in the system option. The “Day-Month-Year” is set as default.

6-138

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.31 Date Setting or Adjustment

3) Example
To set Date “Monday 31 October, 2005”

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “5 BASIC”.
and in SET mode, depress the [↓] key
four times.

Depress the [5] or [Enter] key. “5 BASIC” is selected.

Depress the [↓] key. The cursor is moved on to “2 DATE”.

Depress the [2] or [Enter] key. “2 DATE” is selected.

Depress the [↓] key.

Input 131102005. 1 31 10 2005

31 October, 2005

Day-of Week Code: 1=Monday

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this setting.

31-10-2005 MON #0

DATE
1 31-10-2005

0027 13:15TM

6-139

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.32 Store/Register No. Setting

6.32 Store/Register No. Setting

A maximum of 6 digits may be set as ID No. for the store and/or register. And once set, it will be printed on every
receipt.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] four times then [Enter].

or “5 BASIC” is selected.
Depress [5].

Depress [↓] twice then [Enter].

or “3 REGISTER NO.” is selected.
Depress [3].

Input a 6-digit value. 6-digit value (0 to 999999)

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTE: The preceding zeros, if entered, will not be printed. For example, if “001234” is entered in the above
operation, “#1234” will always be printed as the Register No.

3) Example
To set the Register No. of this ECR 3001

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “5 BASIC”.
and in SET mode, depress the [↓] key
four times.

Depress the [5] or [Enter] key. “5 BASIC” is selected.

(continued on the next page)

6-140

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.32 Store/Register No. Setting

(continued from the previous page)

Operation LCD Display Remarks

Depress the [↓] key twice. The cursor is moved on to “3 REGISTER

NO.”.

Depress the [3] or [Enter] key. “3 REGISTER NO.” is selected.

Input 3001.

(Store/Register No. 3001 is set.)

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this setting.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #0

REG No.
#3001

0028 13:17TM

6-141

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.33 Hourly Range Table Setting

6.33 Hourly Range Table Setting

By setting a maximum of 24 terms per day, sales data control for each term can be performed.

CONDITION After Hourly Range Reset

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] four times then [Enter].

or “5 BASIC” is selected.
Depress [5].

Depress [↓] three times then [Enter].

or “4 HOURLY RANGE” is selected.
Depress [4].

Depress [1] or [Enter]. “1 SETTING” is selected.

Input a numeric value for TIME01, then A 4-digit numeric value is input with the 24 hour time system
depress [Enter]. (HHMM)

Input a numeric value for TIME24, then A 4-digit numeric value is input with the 24 hour time system
depress [Enter]. (HHMM)

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTES:
1. A maximum of 24 terms can be set per day.
2. To partially or entirely change the hourly range table once set, do the entire setting operation over again.
3. Do not set a term across 24:00, such as “23:00 to 1:00”.
4. After performing a RAM Clear, the hourly range table is set with hourly terms in the range of 7:00 to 23:00.

6-142

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.33 Hourly Range Table Setting

3) Example
To set the following hourly range table:
TIME01 until 8:00*
TIME02 8:00 to 12:00
TIME03 12:00 to 15:00
TIME04 15:00 to 19:00
*(The first term is automatically continued from 19:00 of the preceding day.)

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “5 BASIC”.
and in SET mode, depress the [↓] key
four times.

Depress the [5] or [Enter] key. “5 BASIC” is selected.

Depress the [↓] key three times. The cursor is moved on to “4 HOURLY
RANGE”.

Depress the [4] or [Enter] key. “4 HOURLY RANGE” is selected.

Depress the [1] or [Enter] key. “1 SETTING” is selected.

Input 0800, then depress the [Enter] While ? is shown on the upper-right corner
of the LCD display screen, the [?] key
key. depression results in that the following
guidance message appears on the LCD
(TIME01 is set with 8:00.) display.

Input 1200, then depress the [Enter]

key.

(TIME02 is set with 12:00.)

(continued on the next page)

6-143

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.33 Hourly Range Table Setting

(continued from the previous page)

Operation LCD Display Remarks

Input 1500, then depress the [Enter]

key.

(TIME03 is set with 15:00.)

Input 1900, then depress the [Enter]

key.

(TIME04 is set with 19:00.)

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this setting.

• Hourly Range Table Resetting Procedure

If the hourly range table is reset, follow the procedure below.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “5 BASIC”.
and in SET mode, depress the [↓] key
four times.

Depress the [5] or [Enter] key. “5 BASIC” is selected.

Depress the [↓] key three times. The cursor is moved on to “4 HOURLY
RANGE”.

Depress the [4] or [Enter] key. “4 HOURLY RANGE” is selected.

Depress the [↓] key. The cursor is moved on to “2 RESET”.

(continued on the next page)

6-144

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.33 Hourly Range Table Setting

(continued from the previous page)

Operation LCD Display Remarks

Depress the [2] or [Enter] key. “2 RESET” is selected.

A guidance message is displayed.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this setting.

-- Receipt Sample of Hourly Range Table Setting -- -- Receipt Sample for Hourly Range Table Resetting --

TEC STORE TEC STORE

1343 PEACH DRIVE 1343 PEACH DRIVE
PHONE: 87-6437 PHONE: 87-6437

Open 8:00am to 7:00pm Open 8:00am to 7:00pm

Closed: every Wednesday Closed: every Wednesday

31-10-2005 MON #3001 31-10-2005 MON #3001

HOURLY HOURLY
08:00TM
12:00TM 0030 13:21TM
15:00TM
19:00TM

0029 13:19TM

6-145

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.34 Tone Volume Setting

6.34 Tone Volume Setting

Key-in tone for the ECR keyboard and error tone are selectable from High, Low, and OFF.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] four times then [Enter].

or “5 BASIC” is selected.
Depress [5].

Depress [↓] four times then [Enter].

or “5 KEY-IN TONE” is selected.
Depress [5].

Select a key tone with the [↑] or [↓] It is selectable from HIGH, LOW, and OFF.
key.

The [Enter] key depression results in that the selected key tone
[Enter] sounds for 2 seconds. (See NOTE 1 below.)

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTES:
1. The [Enter] key depression results in that the selected key tone sounds for 2 seconds. When the key tone
“OFF” is selected, no sound occurs.
2. After performing a RAM Clear, the key tone “HIGH” is set as standard.

6-146

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.34 Tone Volume Setting

3) Example
To change the key tone from “HIGH” (default setting) to “LOW”.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “5 BASIC”.
and in SET mode, depress the [↓] key
four times.

Depress the [5] or [Enter] key. “5 BASIC” is selected.

Depress the [↓] key four times. The cursor is moved on to “5 KEY-IN TONE”.

Depress the [5] or [Enter] key. “5 KEY-IN TONE” is selected.

Depress the [↑] key. The cursor is moved on to “1 TONE

VOLUME (LOW)”.

Depress the [1] or [Enter] key. “1 TONE VOLUME (LOW)” is selected.

The selected key tone sounds for 2

seconds.

The [End] key depression allows the A long receipt is issued and the display
returns to Main Menu screen.
ECR to end this setting.

31-10-2005 MON #3001

KEY TONE
TONE VOLUME (LOW)

0031 13:23TM

6-147

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.35 Report Item Print/Non-Print Setting

6.35 Report Item Print/Non-Print Setting

Items to be printed on Financial, Cashier, and Salesperson Reports are set here.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] five times then [Enter].

or “6 OTHER” is selected.
Depress [6].

Depress [1] or [Enter] key. “1 REPORT PRINT ITEM” is selected.

Move the cursor on to a report item

name to be set with the [↑] or [↓] key.

Select either Print or Non-print status

for the report item name with the [←] or
[→] key.

[Enter]

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTES:
1. Items which are set with Print status will be printed on the reports. They are not affected by the open/close
status of the key.
2. Financial report item names are programmed in Section 6.14 Financial Report Item Name Programming.
3. All item names are set with Print status after performing a RAM Clear.
4. When the open/close status of the key is changed in the SFKC Programming, perform this setting again to
set the print/non-print status of the corresponding key.

6-148

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.35 Report Item Print/Non-Print Setting

3) Example
To set Item Code 3 “NEG GT” with Non-print status.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “6 OTHER”.
and in SET mode, depress the [↓] key
five times.

Depress the [6] or [Enter] key. “6 OTHER” is selected.

Depress the [1] or [Enter] key. “1 REPORT PRINT ITEM” is selected.

Depress the [↓] key twice. While ? is shown on the upper-right corner
of the LCD display screen, the [?] key
depression results in that the following
(Item Code 3 (“NEG GT”) is selected.) guidance message appears on the LCD
display.

Select either Print or Non-print status The status reverses between Y and N with
with the [←] or [→] key. the [←] or [→] key.

The [Enter] key depression results in

that the setting data is entered.

The [End] key depression allows the A long receipt is issued and the display
ECR to end this setting. returns to Main Menu screen.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #3001

REPORT PRINT
#003 NEG GT 0
#003 NEG GT 1

0032 13:25TM
6-149

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.35 Report Item Print/Non-Print Setting

Report Item Name Table

Item
Item Name Standard Program
Code
1 Ground Total G T
2 NET GT N E T G T
3 NEG GT N E G G T
4 Gross Sale G S
5 Tax 1 (Add-on Tax 1) T A X 1
6 Tax 2 (Add-on Tax 2) T A X 2
7 Tax 3 (Add-on Tax 3) T A X 3
8 Tax 4 (Add-on Tax 4) T A X 4
9 Tax 5 (Add-on Tax 5) T A X 5
10 Tax 6 (Add-on Tax 6) T A X 6
11 Tax 7 (Add-on Tax 7) T A X 7
12 Tax 8 (Add-on Tax 8) T A X 8
13 Tax Total T A X T L
14 Net Sale with Tax N S
15 % I (usually %+) % +
16 % II (usually %-) % -
17 Vendor Coupon V . C P N
18 Amount Discount D I S C
19 Negative Depts. Total - D P T L
20 Special Round Fractions S P . R N D
21 Net Sale (All-Media Sales) N S
22 Cash Sales (AT/TL) C A S H
23 Media 1 Sales (CHK) C H E C K
24 Media 2 Sales (CRT) C R T
25 Media 3 Sales (MISC) M I S C
26 Media 4 Sales (CPN) C P N
27 Media 5 Sales (Credit 1) C R T T L 1
28 Media 6 Sales (Credit 2) C R T T L 2
28 Media 7 Sales (Credit 3) C R T T L 3
30 Media 8 Sales (Credit 4) C R T T L 4
31 Media 9 Sales (Credit 5) C R T T L 5
32 Received-on-Account R / A
33 Paid-Out P O
34 Cash-in-drawer C A S H I D
35 Cash-in-drawer (Foreign Currency 1) C A S H C U R 1 I D
36 Cash-in-drawer (Foreign Currency 2) C A S H C U R 2 I D
37 Cash-in-drawer (Foreign Currency 3) C A S H C U R 3 I D
38 Cash-in-drawer (Foreign Currency 4) C A S H C U R 4 I D
39 Cash-in-drawer (Foreign Currency 5) C A S H C U R 5 I D
40 Media 1-in-drawer (CHK) C H E C K I D
41 Cheque-in-drawer (Foreign Currency 1) C K C U R 1 I D
42 Cheque-in-drawer (Foreign Currency 2) C K C U R 2 I D
43 Cheque-in-drawer (Foreign Currency 3) C K C U R 3 I D
44 Cheque-in-drawer (Foreign Currency 4) C K C U R 4 I D
45 Cheque-in-drawer (Foreign Currency 5) C K C U R 5 I D

6-150

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.35 Report Item Print/Non-Print Setting

Report Item Name Table (Continued)

Item
Item Name Standard Program
Code
46 Media 2-in-drawer (CRT) C R T I D
47 Credit-in-drawer (Foreign Currency 1) C R T C U R 1 I D
48 Credit-in-drawer (Foreign Currency 2) C R T C U R 2 I D
49 Credit-in-drawer (Foreign Currency 3) C R T C U R 3 I D
50 Credit-in-drawer (Foreign Currency 4) C R T C U R 4 I D
51 Credit-in-drawer (Foreign Currency 5) C R T C U R 5 I D
52 Media 3-in-drawer (MISC) M I S C I D
53 MISC-in-drawer (Foreign Currency 1) M I S C C U R 1 I D
54 MISC-in-drawer (Foreign Currency 2) M I S C C U R 2 I D
55 MISC-in-drawer (Foreign Currency 3) M I S C C U R 3 I D
56 MISC-in-drawer (Foreign Currency 4) M I S C C U R 4 I D
57 MISC-in-drawer (Foreign Currency 5) M I S C C U R 5 I D
58 Media 4-in-drawer (CPN) C P N I D
59 Coupon-in-drawer (Foreign Currency 1) C P N C U R 1 I D
60 Coupon-in-drawer (Foreign Currency 2) C P N C U R 2 I D
61 Coupon-in-drawer (Foreign Currency 3) C P N C U R 3 I D
62 Coupon-in-drawer (Foreign Currency 4) C P N C U R 4 I D
63 Coupon-in-drawer (Foreign Currency 5) C P N C U R 5 I D
64 Media 5-in-drawer (Credit 1) C R T I D 1
65 Media 6-in-drawer (Credit 2) C R T I D 2
66 Media 7-in-drawer (Credit 3) C R T I D 3
67 Media 8-in-drawer (Credit 4) C R T I D 4
68 Media 9-in-drawer (Credit 5) C R T I D 5
69 Cash-in-drawer Difference C A S H D I F
70 Media 1-in-drawer Difference C K D I F
71 Media 2-in-drawer Difference C R T D I F
72 Media 3-in-drawer Difference M I S C D I F
73 Media 4-in-drawer Difference C P N D I F
74 Media 5-in-drawer Difference C R T 1 D I F
75 Media 6-in-drawer Difference C R T 2 D I F
76 Media 7-in-drawer Difference C R T 3 D I F
77 Media 8-in-drawer Difference C R T 4 D I F
78 Media 9-in-drawer Difference C R T 5 D I F
79 Item Correct C O R R
80 Void V O I D
81 Misc. Void M I S C V D
82 All Void A L L V D
83 Store Coupon S . C P N
84 Returned Merchandise R T N
85 Negative Mode Total R E G -
86 %- on Line Items % -
87 Amount Discount on Line Items D I S C
88 Transfer Balance GT T R F T L
89 Transfer + GT T R F + G T
90 Transfer – GT T R F - G T

6-151

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.35 Report Item Print/Non-Print Setting

Report Item Name Table (Continued)

Item
Item Name Standard Program
Code
91 Transfer + Daily T R F +
92 Transfer – Daily T R F -
93 PB (Previous Balance) Sales P B T L
94 PB R/A (PB Paid) P B R / A
95 PB PO (PB Refunded) P B P O
96 Taxable Total 1 T X B L 1
97 VAT 1 or Tax 1 V A T 1
98 Taxable Total 2 T X B L 2
99 VAT 2 or Tax 2 V A T 2
100 Taxable Total 3 T X B L 3
101 VAT 3 or Tax 3 V A T 3
102 Taxable Total 4 T X B L 4
103 VAT 4 or Tax 4 V A T 4
104 Taxable Total 5 T X B L 5
105 VAT 5 or Tax 5 V A T 5
106 Taxable Total 6 T X B L 6
107 VAT 6 or Tax 6 V A T 6
108 Taxable Total 7 T X B L 7
109 VAT 7 or Tax 7 V A T 7
110 Taxable Total 8 T X B L 8
111 VAT 8 or Tax 8 V A T 8
112 VAT Total V A T T L
113 Net Sale Without Tax N . N S
114 Tax-exempt Customer V A T E X
115 VAT 1 or Tax 1 Exempt V A T 1 E X
116 VAT 2 or Tax 2 Exempt V A T 2 E X
117 VAT 3 or Tax 3 Exempt V A T 3 E X
118 VAT 4 or Tax 4 Exempt V A T 4 E X
119 VAT 5 or Tax 5 Exempt V A T 5 E X
120 VAT 6 or Tax 6 Exempt V A T 6 E X
121 VAT 7 or Tax 7 Exempt V A T 7 E X
122 VAT 8 or Tax 8 Exempt V A T 8 E X
123 Sales Item Count per Customer I T E M / C U S
124 Sales Amount per Customer T L / C U S
125 No-Sale Counter N O S A L E
126 [C] key Counter C L E A R
127 Consignment Counter C O N S I G N C T R
128 Validation Counter V A L I C T R
129 Money Declaration Counter M . D C R
130 -- vacant --

6-152

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.36 Key Status Programming

6.36 Key Status Programming

Various selective statuses of media keys and other function keys are programmed here.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart
Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] five times then [Enter].

or “6 OTHER” is selected.
Depress [6].

Depress [↓] twice then [Enter].

or “3 KEY FUNCTION” is selected.
Depress [3].

Move the cursor on to a key name to be

programmed with the [↑] or [↓] key,
then depress [Enter].

Move the cursor on to a bit No. to be

programmed with the [↑] or [↓] key,
then select the status with the [←] or
[→] key.

[Enter]

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

3) Example)
To change Bit No. 2 status of Key Code 3 ([CHK TEND]) from SET to RESET.
Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “6 OTHER”.
and in SET mode, depress the [↓] key
five times.

Depress the [6] or [Enter] key. “6 OTHER” is selected.

(continued on the next page)

6-153

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.36 Key Status Programming

(continued from the previous page)

Operation LCD Display Remarks

Depress the [↓] key twice. The cursor is moved on to “3 KEY

FUNCTION”.

Depress the [3] or [Enter] key. “3 KEY FUNCTION” is selected.

Depress the [↓] key twice. The cursor is moved on to “03 CHECK”.

Depress the [Enter] key. “03 CHECK” is selected.

(Key Code 3 “CHECK” is selected.)

Depress the [↓] key, then depress the While ? is shown on the upper-right corner
[→] key. of the LCD display screen, the [?] key
depression results in that the following
guidance message appears on the LCD
display.

The Bit Nos. currently programmed are

displayed on the 7-segment numeric display.
By the [→] key depression, Bit No. 2 status
is changed from “Y” to “N”.

Depress the [Enter] key.

The [End] key depression allows the A long receipt is issued and the display
ECR to end this programming. returns to Main Menu screen.

31-10-2005 MON #3001

KEY STATUS
#03----------------------------7

0033 13:27TM

6-154

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.36 Key Status Programming

Key Status Table (Key Code 1 to 20)

Bit No. Function SET RESET

1 TOTAL-only TOTAL-only key If both SET or RESET:
2 TENDER-only TENDER-only key TOTAL and TENDER
3 -- vacant bit --
4 SHORT TENDERING Prohibited Allowed
5 OVER TENDERING Prohibited Allowed
6 -- vacant bit --
7 NO-PURCHASE CASHING Allowed Prohibited
8 FINALIZING R/A ITEMS Prohibited Allowed
1 CONSIGNMENT Compulsory Free
2 -- vacant bit --
DRAWER OPEN AFTER THE KEY
3 Not Open Open
OPERATION (see NOTE below)

Key
Key Name 1 2 3 4 5 6 7 8 1 2 3
Code
1 R R R
[AT/TL]
2 R
3 R S R R S R
[CHK TEND]
4 R R R
5 S R R R R S
[CRT]
6 R R R
7 R S R R R R
[MISK TEND]
8 R R R
9 R S R S R R
[CPN]
10 R R R
11 S R R R R S
[CREDIT 1]
12 R R R
13 S R R R R S
[CREDIT 2]
14 R R R
15 S R R R R S
[CREDIT 3]
16 R R R
17 S R R R R S
[CREDIT 4]
18 R R R
19 S R R R R S
[CREDIT 5]
20 R R R

NOTE: Regardless of this bit status selection, the drawer opens on over-tendering operation, but does not open
on short-tendering operation.

Description of symbol in the above table:

R = RESET Status
Standard Bit status selection auto-preset after a RAM Clear.
S = SET Status

Those bits marked with either “R” or “S” may be RESET or SET according to your requirements.
= Bit not applicable to the key (Those bits can be SET or RESET.)

6-155

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.36 Key Status Programming

Key Status Table (Key Code 21 to 42)

Bit No. Function SET RESET

1 -- vacant bit --
2 MGR INTERVENTION (in REG mode) Compulsory Free
3 ADD-ON TAX/VAT STATUS All Taxes Taxable Non-taxable
4 -- vacant bit --
5 -- vacant bit --
6 -- vacant bit --
7 -- vacant bit --
8 -- vacant bit --

Key
Key Name 1 2 3 4 5 6 7 8
Code
[ - ] (Disc) 21 R S
[VND CPN] 22 R S
[STR CPN] 23 R S
-- vacant -- 24
[% I] 25 R S
[% II] 26 R S
[RTN MDSE] 27 R
-- vacant -- 28
[VOID] 29 R
-- vacant -- 30
[PO] 31 R
[NS] 32 R
[PB-] 33 R
[EX] 34 R
-- vacant -- 35
[ALL VOID] 36 R
-- vacant -- 37
-- vacant -- 38
-- vacant -- 39
[1st PRICE] 40 R
[2nd PRICE] 41 R
[3rd PRICE] 42 R

Key Codes 43 to 45 are vacant.

NOTE: If RESET status is selected for the [STR CPN] key, the key will always be non-taxable regardless of the
department tax status.

Description of symbol in the above table:

R = RESET Status
Standard Bit status selection auto-preset after a RAM Clear.
S = SET Status

Those bits marked with either “R” or “S” may be RESET or SET according to your requirements.
= Bit not applicable to the key (Those bits can be SET or RESET.)

6-156

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.37 Cash Tender key Preset Amount Setting

6.37 Cash Tender Key Preset Amount Setting

A maximum of 6-digit amount is preset to the Cash Key ([CASH 1] to [CASH 3]).
When depressing the cash key with preset amount in a registration operation, it will be processed as a tendering
operation of the preset amount.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] five times then [Enter].

or “6 OTHER” is selected.
Depress [6].

Depress [↓] three times then [Enter].

or “4 CASH KEY AMOUNT” is selected.
Depress [4].

Input a preset amount of the [CASH 1]. Preset amount: Max. 6 digits (0 to 999999) (See NOTE below.)

[Enter]

Input a preset amount of the [CASH 2]. Preset amount: Max. 6 digits (0 to 999999) (See NOTE below.)

[Enter]

Input a preset amount of the [CASH 3]. Preset amount: Max. 6 digits (0 to 999999) (See NOTE below.)

[Enter]

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTE: When inputting “0”, the preset amount will be reset. An operation of the cash key of which preset
amount is reset may cause an error in a registration transaction.

6-157

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.37 Cash Tender key Preset Amount Setting

3) Example
To preset €10000,00 to the [CASH 1] key and €10,00 to the [CASH 2] key.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “6 OTHER”.
and in SET mode, depress the [↓] key
five times.

Depress the [6] or [Enter] key. “6 OTHER” is selected.

Depress the [↓] key three times. The cursor is moved on to “4 CASH KEY
AMOUNT”.

Depress the [4] or [Enter] key. “4 CASH KEY AMOUNT” is selected.

Input 100000, then depress the [Enter] While ? is shown on the upper-right corner
key. of the LCD display screen, the [?] key
depression results in that the following
guidance message appears on the LCD
(The amount 1000,00 is preset to the display.
[CASH 1] key.)

Input 1000, then depress the [Enter]

key.

(The amount 10,00 is preset to the

[CASH 2] key.)

The [End] key depression allows the A long receipt is issued and the display
ECR to end this setting. returns to Main Menu screen.

31-10-2005 MON #3001

CASH PRICE
01 CASH 1000,00
02 CASH 10,00

0034 13:29TM

6-158

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.38 Drawer Warming Time Setting

6.38 Drawer Warning Time Setting

This operation sets the number of seconds as the period of time for the cash drawer remaining open until the
alarm buzzer is generated to warn operator to close the drawer.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] five times then [Enter].

or “6 OTHER” is selected.
Depress [6].

Depress [↓] four times then [Enter].

or “5 DRW WARNING TIME” is selected.
Depress [5].

Input a numeriv value of time to start

Max. 2 digits: 1 to 99 (seconds)
the drawer warning buzzer.

This programming is ended. A long receipt is issued and the

[End] display returns to Main Menu screen.

NOTES:
1. The value of 0 second cannot be set. (To cancel the drawer warning function, reset the warning option
itself.)
2. After a RAM Clear, the value of 15 seconds is set as the default setting.
3. The setting here is effective only when the following are both selected in the system option programming:
Address No. 27 - Bit No. 1 SET: Drawer-close compulsory
Address No. 27 - Bit No. 2 SET: Drawer warning alarm ACTIVE
4. The drawer warning error is cleared only by closing the drawer. This error cannot be cleared by turning the
Mode Lock to any position.
5. The drawer warning time is processed only in REG, MGR, and – modes.

6-159

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.38 Drawer Warming Time Setting

3) Example
To set 30 seconds for the drawer warning time.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “6 OTHER”.
and in SET mode, depress the [↓] key
five times.

Depress the [6] or [Enter] key. “6 OTHER” is selected.

Depress the [↓] key four times. The cursor is moved on to “5 DRW
WARNING TIME”.

Depress the [5] or [Enter] key. “5 DRW WARNING TIME” is selected.

Input 30.

(The drawer warning time is set to 30

seconds.)

The [End] key depression allows the A long receipt is issued and the display
ECR to end this setting. returns to Main Menu screen.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #3001

DRAWER WNG
30

0035 13:31TM

6-160

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.39 Special Rounding Process Setting, 1-digit type

6.39 Special Rounding Process Setting, 1-digit type

For Special Rounding and Denmark/Australia rounding, the pre-rounded value of the least effective digit and the
post-rounded value are set here. This operation is effective when the option “Special Rounding ACTIVE” and “1
digit subject to Special Rounding” are selected (System Option Address No. 33, Bit No. 3 SET & Bit No. 4
RESET).

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart
Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] five times then [Enter].

or “6 OTHER” is selected.
Depress [6].

Depress [↓] five times then [Enter].

or “6 ROUND TBL 1 DIGIT” is selected.
Depress [6].

Maximum value of the range of the digit

* subject to round (1 digit) Maximum value of the range of the digit subject to round: 0 to 9
+ Post-rounded value: 00 to 09
Post-rounded value (2 digits)

[Enter]

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

*: Repeat for the next break entries (max. 10 breaks).

NOTES:
1. The values shown in the example below are default setting values after a RAM Clear.
2. When the “Post-rounded Value” is to be 10 (i.e. the final break point), the break entry is automatically set
(refer to the example below.). Therefore, it does not need to be entered. Entering a value larger 9 for the
Post-rounded Value will not cause an error. However, the rounding process will occur only on the least
effective digit in sales entries.
3. A maximum of 10 breaks can be programmed.

3) Example
To set the following rounding table:
Pre-rounded value of the
Post-rounded value
least effective digit
0 to 2 0 (=00)
3 to 7 5 (=05)
8 to 9 10 Ignore in setting

6-161

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.39 Special Rounding Process Setting, 1-digit type

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “6 OTHER”.
and in SET mode, depress the [↓] key
five times.

Depress the [6] or [Enter] key. “6 OTHER” is selected.

Depress the [↓] key five times. The cursor is moved on to “6 ROUND TBL 1
DIGIT”.

Depress the [6] or [Enter] key. “6 ROUND TBL 1 DIGIT” is selected.

Input 200, then depress the [Enter] While ? is shown on the upper-right corner
key. of the LCD display screen, the [?] key
depression results in that the following
guidance message appears on the LCD
display.

Input 705, then depress the [Enter]

key.

The [End] key depression allows the A long receipt is issued and the display
ECR to end this setting. returns to Main Menu screen.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #3001

ROUNDING1
200
705

0036 13:33TM

6-162

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.40 Special Rounding Process Setting, 2-digit type

6.40 Special Rounding Process Setting, 2-digit type

For Special Rounding and Denmark rounding, the pre-rounded value of the two least effective digit and the post-
rounded value are set here. This operation is effective when the option “Special Rounding ACTIVE” and “2 digits
subject to Special Rounding” are selected (System Option Address No. 33, Bit No. 3 SET & Bit No. 4 SET).

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] five times then [Enter].

or “6 OTHER” is selected.
Depress [6].

Depress [↓] six times then [Enter].

or “7 ROUND TBL 2 DIGITS” is selected.
Depress [7].

Maximum value of the range of the digit

* subject to round (2 digits) Maximum value of the range of the digit subject to round: 00 to 99
+ Post-rounded value: 00 to 99
Post-rounded value (2 digits)

[Enter]

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

*: Repeat for the next break entries (max. 10 breaks).

NOTES:
1. When the “Post-rounded Value” is to be 100 (i.e. the final break point), the break entry is automatically set
(refer to the example below). Therefore, it does not need to be entered. Entering a value larger 99 for the
Post-rounded value will not cause an error. However, the rounding process will occur only on the two least
effective digits in sales entries.
2. A maximum of 10 breaks can be programmed.
3. Values for Sweden rounding are set after performing a RAM Clear.
4. Example of Sweden rounding
For the Sweden rounding, the amount total is rounded as shown below.
Pre-rounded value of the
Post-rounded value
two least effective digits
0 to 24 00
25 to 74 50
75 to 99 100

6-163

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.40 Special Rounding Process Setting, 2-digit type

Example of Denmark rounding

For the Denmark rounding, the amount total is rounded as shown below.
Pre-rounded value of the
Post-rounded value
two least effective digits
0 to 12 00
13 to 37 25
37 to 62 50
63 to 87 75
88 to 112 100

3) Example
To set the Denmark rounding.
Pre-rounded value of the
Post-rounded value
two least effective digits
0 to 12 00
13 to 37 25
37 to 62 50
63 to 87 75
88 to 112 100 Ignore in setting

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “6 OTHER”.
and in SET mode, depress the [↓] key
five times.

Depress the [6] or [Enter] key. “6 OTHER” is selected.

Depress the [↓] key six times. The cursor is moved on to “7 ROUND TBL 2
DIGITS”.

Depress the [7] or [Enter] key. “7 ROUND TBL 2 DIGITS” is selected.

Input 1200, then depress the [Enter] While ? is shown on the upper-right corner
key. of the LCD display screen, the [?] key
depression results in that the following
guidance message appears on the LCD
display.

(continued on the next page)

6-164

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.40 Special Rounding Process Setting, 2-digit type

(continued from the previous page)

Operation LCD Display Remarks

Input 3725, then depress the [Enter]

key.

Input 6250, then depress the [Enter]

key.

Input 8775, then depress the [Enter]

key.

The [End] key depression allows the A long receipt is issued and the display
ECR to end this setting. returns to Main Menu screen.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #3001

ROUNDING2
1200
3725
6250
8775

0037 13:35TM

6-165

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.41 Number of Receipt Print Buffer Line Setting

6.41 Number of Receipt Print Buffer Line Setting

The number of receipt print buffer line is set here. When it reaches the set value, only a receipt print operation
starts. This setting is effective only in REG, MGR, and - modes or programming operation.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] five times then [Enter].

or “6 OTHER” is selected.
Depress [6].

Depress [↓] seven times then [Enter].

or “8 RCT PRINT BUFFER” is selected.
Depress [8].

Input the Number of receipt print buffer line

Max. 2 digits: 1 to 50
to be set.

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTE: The Number of receipt print buffer line is set to 50 as default setting after performing a RAM Clear.

3) Example
To set the Number of receipt print buffer line is 30 lines.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “6 OTHER”.
and in SET mode, depress the [↓] key
five times.

Depress the [6] or [Enter] key. “6 OTHER” is selected.

(continued on the next page)

6-166

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.41 Number of Receipt Print Buffer Line Setting

(continued from the previous page)

Operation LCD Display Remarks

Depress the [↓] key seven times. The cursor is moved on to “8 RCT PRINT
BUFFER”.

Depress the [8] or [Enter] key. “8 RCT PRINT BUFFER” is selected.

Input 30. Number of receipt print buffer line: max. 2

digits (1 to 50)

The [End] key depression allows the A long receipt is issued and the display
ECR to end this setting. returns to Main Menu screen.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #3001

R PR BUFFER
RECEIPT BUF 30

0038 13:37TM

6-167

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.42 Serial No. Setting

6.42 Serial No. Setting

A maximum of 8-digit serial No. is set here. The serial No. will be printed on the Daily and GT Financial
Read/Reset Reports.

CONDITION Any time outside a sale

OPERATION Mode Lock: SET

1) Menu Tree

2) Operation Flowchart

Main Menu ECR is being outside a sale and in SET mode.

Depress [↓] five times then [Enter].

or “6 OTHER” is selected.
Depress [6].

Depress [↓] eight times then [Enter].

or “9 SERIAL NO.” is selected.
Depress [9].

Input a Serial Number. Max. 8 digits

This setting is ended. A long receipt is issued and the display

[End] returns to Main Menu screen.

NOTES:
1. When inputting 0, the serial No. will be reset. (None of serial No. is printed on the reports.)
2. The serial No. is always printed on the reports with an 8-digit value. If the serial No. 1 is set, ”00000001” is
printed on the reports.

6-168

Downloaded from www.Manualslib.com manuals search engine

 6. TERMINAL FILE PROGRAMMING EO3-11106

6.42 Serial No. Setting

3) Example
To set the serial No. 12345678.

Operation LCD Display Remarks

When the ECR is being outside a sale The cursor is moved on to “6 OTHER”.
and in SET mode, depress the [↓] key
five times.

Depress the [6] or [Enter] key. “6 OTHER” is selected.

Depress the [↓] key eight times. The cursor is moved on to “9 SERIAL NO.”.

Depress the [9] or [Enter] key. “9 SERIAL NO.” is selected.

Input 12345678.

The [End] key depression allows the A long receipt is issued and the display
ECR to end this setting. returns to Main Menu screen.

TEC STORE
1343 PEACH DRIVE
PHONE: 87-6437

Open 8:00am to 7:00pm

Closed: every Wednesday

31-10-2005 MON #3001

SERIAL NO.
#12345678

0039 13:39TM

6-169

Downloaded from www.Manualslib.com manuals search engine

 7. VERIFICATION OF PROGRAMMED DATA EO3-11106

7. VERIFICATION OF PROGRAMMED DATA

7. VERIFICATION OF PROGRAMMED DATA

The programmed data entered in the preceding chapter can be read for verification purposes.
The print format of each program reading is almost the same as on the program receipt, except that “X” is printed
instead of printing Program Name.

CONDITION Any time outside a sale

OPERATION Mode Lock: X or SET

1. Turn the Mode Lock to the X or SET position with the MGR key.
2. In X mode, move the cursor on to “3 PROGRAM DATA READ” which is displayed on the LCD display with
the [↓] key, then depress the [Enter] key.
In SET mode, move the cursor on to “7 PROGRAM DATA READ”, then depress the [Enter] key.
3. PROGRAM DATA READ menu is shown on the next page. Move the cursor on to a desired item to be
verified with the [↓] key, then depress the [Enter] key.
4. The currently programmed data is printed both on the receipt and on the journal.

NOTE: On depressing the [Enter] key, the programmed data will be printed. To abort printing once started,
depress the [ITEM CORR] or [VOID] key. The reading operation is immediately stopped halfway.

Example)
To verify the preset rates of the [%-] and [%+] keys in X mode.

1. When the ECR is being outside a sale and in X mode, depress

the [↓] key twice to move the cursor on “3 PROGRAM DATA
READ”.

2. Depress the [3] or [Enter] key.

3. Depress the [↓] key three times to move the cursor on to “4

RATE, LIMIT AMOUNT”.

4. Depress the [4] or [Enter] key.

5. The [1] or [Enter] key depression results in printing.

31-10-2005 MON #3001

X RATE
%- 5%

0040 13:41TM
7- 1

Downloaded from www.Manualslib.com manuals search engine

 7. VERIFICATION OF PROGRAMMED DATA EO3-11106

7. VERIFICATION OF PROGRAMMED DATA

PROGRAM DATA READ menu

X mode
1 DAILY X
2 GT
3 PROGRAM DATA READ
4 OTHER ITEMS
0
SET mode 1 MESSAGES
4 RATE, LIMIT AMOUNT SET 1 COMMERCIAL MESSAGE
5 BASIC 2 FOOTER MESSAGE
6 OTHER 3 STORE MESSAGE
7 PROGRAM DATA READ
0
2 MAMES
1 DP GROUP NAME
2 CASHIER NAME
3 SALESPERSON NAME
4 FINANCIAL ITM NAME
5 PRINT ITEM NAME
6 DISPLAY ITEM NAME
7 ERROR ITEM NAME
8 X/Z REPORT NAME
9 DISP MENU
0 MESSAGES

3 DP/PLU
1 DP SETTING
1 DP SETTING
2 DIGIT LIMIT(PRICE)
2 PLU SETTING
1 ALL PLU
2 ZONE PLU
3 PLU PRICE SETTING
1 ALL PLU
2 ZONE PLU
4 ASSIGN TO KEYBOARD

4 RATE, LIMIT AMOUNT

1 %- RATE(%-/%+)
2 VAT/TAX RATE
3 CUR EXCHANGE RATE
4 DISC AMT LIMIT

5 BASIC
1 HOURLY RANGE
2 KEY-IN TONE

6 OTHER
1 REPORT PRINT ITEM
2 SYSTEM OPTION
3 KEY FUNCTION
4 CASH KEY AMOUNT
5 DRW WARNING TIME
6 ROUND TBL 1 DIGIT
7 ROUND TBL 2 DIGITS
8 RTC PRINT BUFFER

7- 2

Downloaded from www.Manualslib.com manuals search engine