1. We have two different type of charts are available.

One is rolling chart (laminated from both sides)

& another is wall mounted poster. In wall mounted poster , One Side is Plastic Laminated & Back Side
Pasted On Hardboard with Wooden Frame.

2. Price of each rolling chart is Rs. 350/-per chart of any dept & Price of wall mounted poster is Rs.780/-.

3. The Size of both type of chart is 600mm x 900mm or 2ft x 3ft.

4. Transport charges extra.

5. Delivery period within 3-4 weeks after receiving confirmed purchase order along with
advance Payment .
6. Payment in advance along with confirmed purchase order.

7. Once order received will not be cancelled or no changes can be made.

8.We have also attached a scan copy of chart at the end of the following list.

List Of Mechanical Chart.

Sr. Name of Chart Code Sr. Name of Chart Code
No. No. No. No.
01 Cochran Boiler 001 41 Fuel & Ash Handling System 041
02 Babcock Wilcox Boiler 002 42 H.P, Boiler 042
03 Lancashire Boiler 003 43 Pulversied Fuel System 043
04 Loco Type Boiler 004 44 Pressure Regulating Valve 044
05 Nuclear Power Plant 005 45 Vertical Tubular Boiler 045
06 General Steam Plant 006 46 Cornish Boiler 046
07 Coil Type once Through Boiler 007 47 Newclear Power 047
08 Loeffler Boiler 008 Station(French Station)
09 Benson Boiler 009 48 Fluidized Bed Boiler 048
10 La-Mont Boiler 010 49 Thermodynamic Steam Trap 049
11 Velox Boiler 011 50 Spring Loaded Safety Valve 050
12 Pressure Gauge 012 (Y-Type)
13 Water Level Indicator 013 51 Spring Loaded Safety Valve) 051
(Pop Type)
14 Steam Stop Valve 014
52 Vertical Inverted Steam Trap 052
15 Feed Check Valve 015 (Bucket Type)
16 Blow Off Cock 016 53 Separating Calorimeter 053
17 Dead Weight Safety Valve 017 54 Reaction Turbine 054
18 Ram's Bottom Safety Valve 018 55 Single Stage Impulse Turbine 055
19 Lever Safety Valve 019 56 Throttling Calorimeter 056
20 High Steam Low Water Safety 020 57 Reheating in Steam Turbine 057
Valve
58 Jet Condenser 058
21 Fusible Plug 021
59 Pressurised Water Reactor 059
22 Coil Type Economiser 022
60 Electro Static Precipitor 060
23 Green's Economiser 023
61 Boiling Water Reactor 061
24 Super Heater 024
62 Steam Turbine Governing 062
25 Air Preheater 025
63 Thermal Power Plant 063
26 Surface Condenser 026
64 Candu Reactor 064
27 Steam Trap 027
65 Air Extraction 065
28 Water Feed Pump 028
66 Gas Power Plant 066
29 Woolf Compound Steam Engine 029
67 Two Stage Reciprocating 067
30 Compound Separating & Throttling 030 Compressor
Calorimeter
68 Phase Transformation of Steam 068
31 Type of Compound Steam Engine 030 (Constant Pressure)
32 Impulse Reaction Steam Turbine 032 69 Temperature Enthalpy Chart of 069
33 Re-Entry Type Impulse Steam 033 Steam
34 Pressure Compounded Impulse 034 70 Phase Transformation (P.V.T. 070
Steam Turbine Data) - l
35 Velocity Compounded Impulse 035 71 Phase Transformation (P.V.T. 071
Steam Turbine Date) - ll
36 Velocity & Pressure Compounded 036 72 Pressure, Temperature Curve 072
Impulse Steam Turbine for Steam
37 Double Acting Steam Engine 73 Types of Condenser 073
38 Lubricators (steam Engine) 74 Types Of Steam Nozzles 074
39 Types of Steam Condenser 75 Water Tube Boiler 075
40 Steam Flow Meters 76 Fire Tube Boiler 076
77 Boiler Mountings 077
 78 Forced Draught 078
79 Induced Draught 079
80 Balanced Draught 080

Production Technology Section (PS-101)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Tool Geometry - I 101 33 Drilling Machine 133
02 Types of Milling Cutters 102 (Type/Construction)
03 Milling Operation-I 103 34 Jig Boring Machine 134
04 Milling Operation-II 104 35 Jig Boring Machine 135
05 Elements of Jig & Fixture-I 105 36 Gear Hobbing Machine 136
06 Elements of Jig & Fixture-II 106 37 Variable Speed Drive 137
07 Types of Clamp & Locator 107 38 Single Spindle Automat 138 138
(Mechanism)
08 Principle & Types of Centreless 108
Grinding 39 Self Opening Diehead 139
09 Hand Tools used for Carpentry 109 40 Types of Collect Chuck 140
10 Press Tools 110 41 Types of Cutter Holder & Work 141
Holder in Milling Machine
11 Types of Broaches 111
42 Slotting Machine 142
12 Centre Lathe 112
43 Abrasive Jet machining 143
13 Dividing Head 113
44 Electro Chemical Machining 144
14 Tool Force Dynamometer 114 (ECM)
15 Types of Chip & Chip Breaker 115 45 Electron Beam Machining 145
16 Details of Centre Lathe 116 (EBM)
17 Turret Lathe 117 46 Electrical Discharge Machining 146
18 Automat 118 (EDM)
19 Turret Indexing Mechanism 119 47 Laser Beam Machining (LBM) 147
20 Tool Geometry-II 120 48 Plasma Arc Machining (PAM) 148
21 Constructional details of Capstan 121 49 Methods of Metal Cutting 149
& Turret Lathe (Orthogonal / Oblique)
22 Tool Layout of Turret Lathe 122 50 Different Shapes of Grinding 150
Wheels
23 Shaping Machine (Construction) 123
51 Quick Return Mechanism of a 151
24 Hydraulic Shaper Mechanism 124 Shaper Machine
25 Turret Tool Holders 125 52 Elements of Plain Milling Cutter 152
26 Planing Machine (Construction) 126 53 Broaching Operations 153
27 Milling Machine 127 54 Lathe Tail Stock 154
(Type/Construction) 55 Drill Sleeve & Socket 155
28 Milling Machine 128 56 Quick Change Chuck 156
(Type/Construction)
57 Drill Size for Cleaning Holes of 157
29 Gear Cutting Processes 129 Withworth
30 Broaching Machine 130 58 Regrinding Milling Cutter 158
(Type/Construction)
59 Screw Thread Chart UNC & 159
31 Sawing Machine 131 UNF Charts
(Type/Construction)
60 Plain Bearing 160
32 Grinding Machine 132
(Type/Construction) 61 Air Bearing 161
62 Rolling Bearing 162
63 Hydraulic Circuits of Machine 163
Tools
64 Power Transmission 164
Top

Welding Technology Section (WT-3201)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Weld Symbols - I 3201 23 Welding Process 3223
02 Weld Symbols-II 3202 24 Principle Chart of Welding 3224
03 Fabrication, Welding Tools & 3203 Process
Equipment 25 Kinds of Weld 3225
04 Electric Resistence Welding 3204 26 Oxyacetylene Welding 3226
05 Submerged Arc Welding 3205 Equipment
06 Spot Welding 3206 27 Production of Oxygen Gas 3227
07 Seam Weldingm 3207 28 Water to Carbide Acetylene 3228
Generator
08 Flash Welding 3208
29 Carbide to Water Acetylene 3229
09 Types of Welding Torch 3209 Generator
10 Types of Flame 3210 30 Electrod 3230
11 Automatic Hydrogen Welding 3211 31 Weld Blow Pipe 3231
12 Thermit Welding 3212 32 Polarity (Prositive and Negative) 3232
13 MIG Welding 3213 33 Defects in Welding 3233
14 TIG Welding 3214 34 Types of Distortion 3234
15 Electrosag Welding 3215
16 Laser Beam Welding 3216 35 Welding Sequence 3235
17 Plasma Arc Welding 3217 3217 36 Welding Techniques 3236
18 OXY-Acetylene Torch 3218 37 Welding Test 3237
19 Arc Welding Equipments 3219 38 Pipe Welding 3238
20 Welding Tools 3220 39 Gas Welding 3239
21 Weld Gauges 3221 40 Arc Welding 3240
22 Types of Welded Joints 3222 41 Welding Machines 3241
42 Metal Cutting 3242
43 Safety - I 3243
44 Safety - II 3244

Foundary Technology Section (FT-3301)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Hand Tools used for Smithy 3301 17 Oil Furnace 3317
02 Hand Tools used for Fitting 3302 18 Moulding Boxes 3318
03 Tin Smithy Tools & Equipment 3303 19 Laddle 3319
04 Special Casting Methods 3304 20 Melting Points 3320
05 Forging Equipment & 3305 21 Speedy Moisture Tester 3321
Operations 22 Permability Meter 3322
06 Rolling Equipment & Operations 3306 23 Universal Strength 3323
07 Methods of Pipe &Tube 3307 TestingMachine
Manufacture 24 Sand Rammer 3324
08 Plastic Moulding Methods 3308 25 Separate The Remaining Clay 3325
09 Carpentry Joints 3309 From The Sand
10 Types of Gate - I 3310 26 Shattered Indes Tester 3326
11 Types of Gate - II 3311 27 Universal Strength Machine 3327
12 Types of Core 3312 28 mCore And Mould Hardness 3328
13 Types of Moulding Machine 3313 Tester
14 Moulding Hand Tools 3314 29 Permeability Test 3329
15 Cupola Furnace 3315 30 Rapid Moisture Tester 3330
16 Pit Furnace 3316 31 Blast Furnace 3331
Top
Internal Combustion Engine & Thermodynamic Section (ICETDS-401)
Sr. Name of Chart Code Sr. Name of Chart Code
No. No. No. No.
01 Two Stroke Cycle 401 44 General I.C. Plant 444
02 Four Stroke Cycle 402 45 Gas Producer Plant 445
03 Spark Ignition (2 Stroke/4 403 46 Variable Compression Engine 446
Stroke) 47 Governers of I. C. Engine 447
04 Compression Ignition (2 404 48 Lubricating Oil Filter Test Rig 048
Stroke/4 Stroke)
49 Air Filter Test Rig. 449
05 Valve Timing Diagram (Low 405
Speed/High Speed) 50 Fuel Filter Test Rig. 050
06 Type of Battery Ignition System 406 51 Elements of Condensing Unit 451
07 Type of Magnato Ignition 407 52 Parallel Flow Jet Condenser 052
System 53 Counter Flow Jet Condenser 053
08 Type of Electronic Ignition 408 54 High Level Jet Condenser 454
System 55 T-H-S Chart 055
09 Type of Fuel Pump (Bosch Fuel 409 56 Mollier Chart 456
Injection Pump Mech.)
57 Valve Arrangement 057
10 Electric Fuel Pump 410
58 Oil Filled Ignition Coil 458
11 Fuel Injection System 411
(Mechanical) 59 Electrical / Vacuum Fuel Pump 059
12 Fuel Injection System 412 60 Distributor 460
(Electronic) 61 Layout of Simple Fuel Injection 461
13 Fuel Injection System (Air 413 System
Supply) 62 Bio Gas Plant 462
14 Fuel Injection System (Fuel 414 63 Lay out of Simple Carburator 463
Supply) 64 Simple Two Stroke Petrol 464
15 Type of Injectors 415 Engine
( CAV,GARDNER, MORRIES ) 65 Simple Two Stroke Diesel 465
16 Solex Carburettors 416 Engine
17 S.U. Carburettors 417 66 Layout of I. C. Engine 466
18 S.U. Carburettors 418 67 Fuel Supply System of Petrol 467
19 Combustion Chamber for 419 Engine
S.I.Engine 68 Ignition System in S. I. Engine 468
20 Wankle Engine with Cycle 420 69 Carnot Cycle for Refrigeration 469
21 Types of Lubricator - I 421 System
22 Types of Lubricator-II 422 70 Rankine Engine (Ideal Cycle) 470
23 Bomb Calorimeter 423 71 Rankine Engine (Rankine Cycle) 471
24 Boys Gas Calorimeter 424 72 Closed Cycle Gas Turbine Plant 472
25 Lubrication System of I.C. 425 73 Types of Rotry Compressor 473
Engine-I 74 Combustion in C.I. Engine 474
26 Lubrication System of I.C. 426 75 Types of Nozzles 475
Engine-II
76 Electronic Transistorized Coil 476
27 Centrifugal Compressor 427 Ignition System
28 Axial Flow Compressor 428 77 Electronic Capacitive Discharge 477
29 Reciprocating Air Compressor 429 Ignition
30 Triple Venturi Carburettor 430 System
31 Grease Penetrometer 430 78 Combustion in S.I. Engine 478
32 Orsat Apparatus 432 79 Rotary-Distributor Injection 479
Pump
33 Red Woods Viscometer 433
80 In-Line Plunger Type Fuel 480
34 Flash & Fire Point Apparatus 434 Injection Pump
35 Conradson Carbon Residue 435 81 Condenser 481
Apparatus
82 Types of Turbo Charger 482
36 Grease Dropping Point 436
Apparatus 83 Types of Super Chargers 483
37 Cloud & Pour Point Apparatus 437 84 A.C. Fuel Pump 484
38 Aniline Point Test 438 85 Automiser 485
39 Gas Turbine Plant 439 86 Junkers Gas Calorimeter 486
40 Types of Solar Collector 440
41 Types of Wind Turbine 041
42 Gobar Gas Plant-Layout 442
43 Tidal Power Plant 043
Top

Refrigeration & Air Conditioning Section (RACS-301)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Vapour Compression 301 23 Hermetic Sealed Compressor 323
Refrigeration 24 Constant Pressure Expansion 324
02 Vapour Absorption Refrigeration 302 Valve
03 Window Air Conditioner 303 25 Thermostatic Expansion Valve 325
04 Electrolux Refrigerator 304 26 Refrigeration Chart 326
05 Layout of Ice Plant 305 27 Electric Controls In 327
06 Steam Jet Refrigeration 306 Refrigeration-I
07 Vortex Tube Refrigeration 307 28 Electric Controls In 328
08 Air Refrigeration Cylce 308 Refrigeraton-II
09 Thermoelectric Refrigeration 309 29 Air & Water Heat Pump 329
10 Adiabatic Demagnetisation 310 30 High & Low Side Refregeration 330
11 Refrigeration Controls 311 System
12 Air Conditioning Controls 312 31 Water Cooled Condenser 331
13 Psychrometric Charts 313 32 Tube in Tube or Double Tube 332
Type Water Cooled Condenser
14 Freon- P-H- Charts 314
33 Central Air Conditioning System 333
15 Cryogenics - Linde Cycle 315
34 Simple Aircraft Air Conditioning 334
16 Cryogenics-Cloude Cycle 316 System
17 Cold Storage 317 35 Charging Of Refrigeration 335
18 Desart Cooler 318 System
19 Water Cooler 319 36 Boot-Strap Evaporative Aircraft 336
20 Domestic Refrigerator (Working 320 Air
Principle) Conditioning Cycle
21 Indirect Refrigeration System 321 37 Boot-Strap Evaporative Aircraft 337
Air
22 Evaporating Cooling 322 Cooling System
38 Regenerative Aircraft Air 338
Cooling System
39 Reduced Ambient Aircraft Air 339
Cooling System
40 Simple Evaporative Cooling 340
System
41 Lithium Bromide ( Li-Br ) 341
Vapour
Absorption Cycle
42 Reversed Brayton Cycle 342

Heat Transfer Section (HT-1851)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Thermal Conductivity of 1851 19 Counter Flow Heat Exchanger 1869
Insulating Powder 20 Single & Multi Pass Heat 1870
02 Two Slab Guarded Hot Plate 1852 Exchanger
Apparatus 21 Cross-Flow Heat Exchanger 1871
03 Heat Transfer in Natural 1853 22 Fixed Tube Sheet Heat 1872
Convection
04 Heat Transfer in Forced 1854 Exchanger
convection 23 External Floating Head Heat 1873
05 Extended Surfaces 1855 Exchanger
06 Stefan Boltzman Apparatus 1856 24 Internal Floating Head Heat 1874
07 Types of Heat Exchanger 1857 Exchanger
08 Shell & Tube Heat Exchanger 1858 25 Double Pipe Heat Exchanger 1875
09 Pool Boiling Phenomenon 1859 26 U-Tube Heat Exchanger 1876
10 Heat Pipe 1860 27 Reboiler Heat Exchanger 1877
11 Thermal Conductivity of Metal 1861 28 Plate Type Heat Exchanger 1878
Bar 29 Rediation Heat Transfer 1879
12 Heat Transfer in Condensation 1861 30 Reboiler Heat Exchanger 1880
13 Properties of Air 1863 31 Critical Heat Flux 1881
14 Properties of Saturated Water 1864 32 Emissivity Measurement 1882
15 Heat Exchange Equipment 1865 33 Heat Transfer in Pin Fin 1883
16 Types of Formed Head 1866 34 Thermal Conductivity Of 1884
17 Nozzel Reinforcement to Shell 1867 Composite Wall
Wall 35 Filmwise & Dropwise 1885
18 Parallel Flow Heat Exchanger 1868 Condensation
36 Bearnouli's Theorm 1886
37 Reynolds Experiment 1887
Top

Automobile Engineering Section (AES - 801)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Lucas Petrol Injection System 801 37 Power Transmission Line Layout 837
02 Multi Cylinder Petrol Engine 802 38 Cross Section View of Battery 838
03 Multi Cylinder Diesel Engine 803 39 Automobile General Layout 839
04 Engine Cooling-Thermosiphon 804 40 Air Filteration System for Four 840
& Air Cooling Pump Circulation Cylinder Engine
05 Types of Air Filter 805 41 Spark Plug 841
06 Fluid Friction Clutch 806 42 Transfer Case 842
07 The Ferlec Electro-Magnetic 807 43 Tyre Wear Chart 843
Clutch 44 Electric Horn & Flasher Circuits 844
08 Principle of Centrifugal Clutch 808 45 Starter Assembly 845
09 Multiple Plate Clutch 809 46 Valve Gear Mechanism 846
10 Diaphragm Spring Clutch 810 47 Types of Fuel Filter 847
11 Single Plate Clutch 811 48 Sectioned Six Cylinder Car 848
12 Internal Expanding Brake 812 Engine
System 49 Interlocking System 849
13 Disc Brake 813 50 Truck / Bus (Diesel Type) Cut 850
14 Master Cylinder 814 Sectional View
15 Power Operated Brakes 815 51 Scooter Cut Sectional View 451
16 Duel Power Operated Brake 816 52 Radiators, Fans 852
System 53 Shock Absorber 853
17 Compressed Air System 817 54 Types of Lubricating Pump 854
18 Hydraulic Wheel Cylinder 818 55 Fork Lift Truck 855
Assembly 56 Wiper Motor 856
19 Differential 819 57 Air Filter & Silencer 857
20 Sliding Mesh Gear Box 820 58 Alternator 858
21 Constant Mesh Gear Box 821 59 Oil Pressure Switch 859
22 Synchromesh Device 822 60 Petrol Gauge Dash & Tank Unit 860
23 Epicyclic Gear Box 823 61 Thermostat 861
24 Torque Converter 824 62 Radiator Pressure Cap 862
25 Automatic Gear Box 825 63 Speedometer 863
26 Universal Joint 826 64 Oil Filter (Full Flow & By-Pass 864
27 Universal Joint Propeller Shaft 827 Flow)
28 Constant Velocity Universal 828 65 Oil Bath & Air Cleaner 865
Joint 66 Centrifugal Oil Filter 866
29 Perpendicular Type Suspension 829 67 Temperature Guage & Sender 867
Single Arm & Double Arm Unit
30 Parallel Type Suspension Single 830 68 Layout of S.I. Engine 868
Arm & Double Arm
69 Cooling System in S.I. & C. I. 869
31 Strut Type and Sliding Type 830 Engine
Suspension
70 Hydraulic System of Tractor 870
32 Swinging Arm Type Suspension 832
71 Cone Clutch 871
33 Rack & Pinion Steering 833
Mechanism 72 Hydraulic Brake System 872
34 Cam Steering Mechanism 834 73 Electrolyte Preparation & 873
(Screw & Lever Mechanism) Specific Gravity Test Procedure
Of Hydrometer
35 Ackerman System of Steering 835
74 Battery Maintenance Safety 874
36 Details of Generator Cum 836
Alternator
 Metallurgy Section (MS - 1201)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Optical Pyrometer 1201 25 Cooling Curve for Pure Iron 1225
02 Thermocouple Applications 1202 26 Iron-Iron Carbide Equillibrium 1226
03 Optical Microscope 1203 Diagram
04 Comparison of Optical & 1204 27 Cooling Curves and the I-T 1227
Electron Microscope Diagram
05 Common Crystal Structure 1205 28 Correlative of Continuous 1228
Cooling
06 Iron Carbon Digram 1206
29 Schematic Transformation 1229
07 Steel Structure 1207 Diagram
08 Cupola Furnace 1208 30 Induction Hardening Coils 1230
09 Grain Size 1209 31 Specific Effects of Alloying-I 1231
10 T-T-T- Diagram 1210 32 Specific Effects of Alloying-II 1232
11 Cu-Zn Diagram 1211 33 Comparative Properties of Some 1233
12 Cu-Sn Diagram 1212 Tool Steels
13 Precipitation Hardening 1213 34 Metastable Iron-Iron Carbide 1234
14 Non Destructive Tests 1214 Phase Diagram
15 Graphite Flask Type and Size 1215 35 Cu-Zn Phase Diagram (Cu-rich) 1235
Chart 36 Cu-Tin Phase Diagram (Cu-rich) 1236
16 Hardness Conversion Table 1216 37 Cu-Aluminum Phase Diagram 1237
17 Mechanism of Electrochemical 1217 (Cu-Rich)
Corrosion 38 Cu-Silicon Phase Diagram (Cu- 1238
18 Reverberatory Furnace 1218 rich)
19 Material Weight & Volume 1219 39 Cu-Beryllium Phase Diagram 1239
Chart (Cu-rich)
20 Non-Metallic Inclusion Chart in 1220 40 Al-Alloys Phase Diagram (Al- 1240
Steel rich)-I
21 Jominy End Quench Test 1221 41 Al-Alloys Phase Diagram (Al- 1241
Rich)-II
22 Spark Test 1222
42 Magnesium Alloys Phase 1242
24 Recrystallization chart & 1224 Diagram (Mg-rich)
Representation
43 Nickel Iron Alloys Phase 1243
Diagram
44 Titanium Alloys Phase Diagram 1244
 45 Titanium Manganese Alloys 1245
Phase Diagram
46 Zinc Alloys Phase Diagram 1246
47 Silver-Copper Alloys Phase 1247
Diagram
Top

ENGINEERING DRAWING (ENGDR - 901)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Methods of Projection 901 23 Types of Bolt, Nut, Washer, 953
02 Conventional Representation of 902 Screw-I
Lines & Materials 24 Types of Bolt, Nut, Washer, 924
03 Projection of Lines - I 903 Screw-II
04 Projection of Lines - II 904 25 Standard Tapers,(Metric and 925
Morse)
05 Orthographic Projction - I 905
26 Joints (Knuckle, Strap, Cotter) 926
06 Orthographic Projection - II 906
27 Cams and Cam Profiles 927
07 Isometric Projection 907
28 Sections of Solids 928
08 Oblique Projection 908
29 Interpenetration of Surfaces of 929
09 Perspective Projection 909 Solids
10 Conventional Representation of 910 30 Development of Surfaces of 930
Common Engineering Solids
Components & Features
31 Rolled Sections and 931
11 Section & Cutting Planes 911 Terminology
12 Dimensioning & Tolerance in 912 32 Construction of Conic Section 932
13 Indication of surface roughness, 913 33 Construction of Cycloid Curve 933
direction of lays on working
drawings 34 Construction of Involute 934
14 Rivets & Joints 914 35 Projection of Planes 935
15 Wel ds & Joints 915 36 Conventional Representation of 936
Common Features-I
16 Types of Thread and Profiles 916
37 Conventional Representation of 937
17 Types of Fits 917 Common Features-II
18 Types of Gear and Profiles 918 38 Conventional Representation of 938
19 Types of Coupling 919 Spring
20 Types of Coupling 920 39 Representation of Gear 939
21 Types of Bearing 921 Assemblies
40 Types of Section-I 940
22 Types of Pulleys 922 41 Types of Section-II 941
42 Types of Section III 942
43 Types of Pipe Joints 943
44 Screw Jack 944
Top

INDUSTRIAL ENGINEERING (IE - 2001)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Factors Affecting Productivity 2001 32 Allowances 2032
02 Factors Raising Productivity 2002 33 Standard Time 2033
03 Approach of Work Study 2003 34 Maslow's Hierarchy of Need 2034
04 Method Study Procedure 2004 35 Properties of Various Industrial 2035
05 Principles of Motion Economy 2005 Floor Surfaces
06 Fundamental Hand Motion 2006 36 Light Intensity Chart 2036
07 Recording Techniques Part-I 2007 37 Ergonomic Display Design 2037
08 Recording Techniques Part-II 2008 38 Ergonomic Design of Controls 2038
09 Recording Techniques Part-III 2009 39 Operator & Work Place 2039
Dimensions
10 Flow Process Chart Symbol 2010
40 Human Standing of the Standing 2040
11 Multiple Activity Charts Symbol 2011 Adult Male
12 Travel Chart 2012 41 Human Standing of the Standing 2041
13 String Diagram 2012 Adult Female
14 Cyclegraph & Chrono 2014 42 Types of Wage Plan-I 2042
Cyclegraph 43 Types of Wage Plan-II 2043
15 Pre-Determined Motion Time 2015 44 Type of Incentive Plans - I 2044
Measurement
45 Type of Incentive Plans - II 2045
16 Motion Time Measurement 1 & 2046
2 46 Different Merit Rating Method 2046
17 Motion Time Measurement 3 & 2017 47 Fundamental Organisation of 2047
5 Production Planning and Control
18 Work Factor System 2018 48 Production Planning and Control 2048
Procedure
19 Plant Layout Principles & 2019
Objectives 49 Work Sampling Method 2049
Procedure
20 Product Plant Layout 2020
50 Work Sampling Method Merit & 2050
21 Process Plant Layout 2021 Demerit
22 Combination Plant Layout 2022 51 Methods of Job Evaluation 2051
23 Different Types of Flow Pattern 2023 52 Schematic Details for Belt 2052
24 Plant & Factory Layout 2024 Conveyer
Analogues 53 Belt Centralizing Arrangement 2053
25 Principle of MTL Handling 2025 54 Bucket Elevator Assembly 2054
26 Types of MTL Handling 2026 55 Type of Bucket 2055
Equipment 56 Loading & Unloading of Bucket 2056
27 Scope of Motion & Time Study 2027 57 Screw Conveyer Assembly 2057
28 Combination of Motion & Time 2028 58 Type of Screw Flights 2058
Study
59 Pneumatic Conveying System 2059
29 Normal & Maximum Working 2029
areas & Different Class of 60 Fedders for Pneumatic System 2060
Motion 61 Vertical Screw Conveyer 2061
30 Work Measuring Equipment 2030
31 Work Measuring Elements 2031
Top

THEORY OF MACHINE SECTION (TMS - 1601)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Types of Gears 1601 18 Inversion of Four Bar Chain 1618
02 Types of Kinematic Pairs 1602 19 Oscillating Cylinder 1619
03 Types of Kinematic Chain 1603 20 Quick Return Mechanism 1620
04 Types of Cam & Follower 1604 (Withworth)
05 Pentograph, Straight-Line 1605 21 Types of Brake 1621
Mechanism 22 Types of Clutch 1622
06 Geneva Mechanism 1606 23 Kinematic of Gears 1623
07 Terminology for cam followers 1607 24 Generation of Involute & 1624
Mechanism Cycloid germ tooth Profile
08 Classification of Belt, Rope, 1608 25 Interference and Under Cutting 1625
Chain Drivers 26 Bevel Gear Assembly 1626
09 Gear Nomenclature 1609 27 Worm & Worm Wheel Gear Box 1627
10 Slider Crank Mechanism 1610 28 Spur - Bevel Gear Box 1628
11 Compound Pendulum 1611 29 Cycloid Gears 1629
12 Trifler Suspension 1612 30 Epicyclic Gear 1630
13 Gyroscope 1613 31 Damped Free Longitudinal 1631
14 Types of Governor 1614 Vibration
15 Balancing (Static & Dynamic) 1615 32 Roller Support Revolving 1632
16 Damped Free Torsional 1616 Assembly for Belt Centering
Vibration 33 Arrangement for Belt 1633
17 Damped Free Transverse 1617 Centralizing
Vibration

METROLOGY QUALITY CONTROL (MQC - 2101)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Methods of Measurement 2101 35 N.P.L. Interferometer 2135
02 Non Precision Measuring Tools 2102 36 Pitter-N.P.L. Interferometer 2136
03 Surface Plates 2103 37 Laser Interferometer 2137
04 Beam Comparator 2104 38 Vernier & Optical Bevel 2138
05 Spirit Levels 2105 Protector
06 Combination Set 2106 39 Mechanical Bevel Protractor 2139
07 Universal Surface Gauge 2107 40 Optical Bevel Protractor 2140
08 Engineer's Square 2108 41 Uses of Sine Bar 2141
09 Vernier Caliper 2109 42 Principle of Auto Collimator 2142
10 Types of Vernier Caliper 2110 43 Photo Electric Auto Collimator 2143
11 Micrometer 2111 44 Microptic Auto Collimator 2144
12 Inside Micrometer 2112 45 Angle Dekkor 2145
13 Types of Micrometer-I 2113 46 Pneumatic Sizing Device 2146
14 Types of Micrometer-II 2114 47 Tomlinson Surface Meter 2147
15 Slip Gauges 2115 48 Taylor-Hobson Talysurf 2148
16 Standards of Measurements 2116 49 Manufacturing Process & 2149
Expected Values of Roughness
17 Types of Fit-I 2117
50 Different Types of Lay 2150
18 Types of Fit-II 2118
51 Tracer Type of Profilogram 2151
19 Grade and Tolerance 2119
52 Dial Gauge Indicator 2152
20 Plain Plug Gauges-I 2120
53 Dial Guage Applications 2153
21 Plain Plug Gauges-II 2121
54 Pass Meter & Internal Dial 2154
22 Plain Ring Gauges 2122 Gauge
23 Snap Gauges 2123 55 Measurement of Threads 2155
24 Limit Gauges 2124 56 Thread Gauges 2156
25 Geometric Characteristics & 2125 57 Gear Tooth Measurement 2157
Symbol-I
58 Spur Gear Tester 2158
26 Geometric Characteristics & 2126
 Symbols-II 59 Measurement of Gears using 2159
27 Mechanical Comparator-I 2127 Gratings
28 Mechanical Comparator-II 2128 60 Bausch of Lomb Projector 2160
29 Mechanical Optical Comparator 2129 61 Verticle Optimeter 2161
30 Electro-Mechanical Comparator 2130 62 Horizontal Optimeter 2162
31 Pneumatic Comparators 2131 63 Small Tool Maker's Microscope 2163
32 Solex Pneumatic Gauges 2132 64 Laser Telemetric System 2164
33 Differential Comparator 2133 65 Automatic Gear's Measuring 2165
Machine
34 Michelson Interferometer 2134
66 Quality Control Chart 2166
67 Vernier Height Gauge/Depth 2167
Gauge
Top

CHEMICAL ENGINEERING (CHS-2201)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Ball Mill (Conical) 2201 19 Rotary Drum Filter (Alongwith 2219
02 Jaw Crusher 2202 Flow Sheet)
03 Gyratory Crusher 2203 20 Top-Suspended Basket 2220
Centrifuge
04 Smooth Roll Crusher / Single 2204
Roll Toothed Crusher 21 Tubuler Bowl Centrifuge 2221
05 Attrition Mill 2205 22 Disc Bowl Centrifuge 2222
06 Fluid Energy Mill 2206 23 Gravity Thickner 2223
07 Close Circuit Grinding 2207 24 Types of Thickner & Clarifier 2224
08 Selection of Comminution 2008 25 Cross Flow Wet Setting 2225
Equipment Classifier
09 Two Arm Kneader 2209 26 Cyclone & Hydro-cyclone 2226
10 Banbury Internal mixer 2210 27 Impingement Separator 2227
11 Muller Mixer 2211 28 Magnetic Separator / Electostatic 2228
Seperator
12 Ribbon Mixer 2212
29 Hydraulic Jig 2229
13 Tumbler Mixer 2213
30 Froth Flotation Cell 2230
14 Motion of Screens 2214
31 Electro-static Precipitator 2231
15 Gyrating Screens 2215
32 Petroleum Refinery (Fractional 2232
16 Comparison of Ideal v/s Actual 2216 Distillation)
Screening
33 Ion Exchange Process Plant 2233
17 Trommels 2217 34 Mechanism of Electrolysis 2234
18 Plate & Frame Filter Press 2218 35 P.H.Scale 2235
36 Flow Sheet of Extraction of Ore 2236
37 Electrochemical Cell 2237

ENERGY ENGINEERING ( EES-2301)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Solar Power Generation 2301 36 Schematic of a Down Draft 2336
(Photovoltaic) Gasifier
02 Different Parts of Wind Power 2302 37 Schematic of a Cross-Draft 2337
Plant Gasifier
03 Geothermal Type of Generation 2303 38 Schematic of a Complete Bio- 2338
04 Flat Plate Collector Type of 2304 Mass
Generator 39 Schematic Diagram of Gasifiers 2339
05 Wind Power Generation 2305 40 Schematic Diagram of a Small 2340
06 Biomass Type of Generator 2306 Scale Gasifier Power Plant
07 Pyranometer (For measuring 2307 41 Schematic of a Vapour 2341
global Radiation) Dominated Power Plant
(Geothermal Principle)
08 Shading Ring (Arrangement for 2308
Measurement of Diffuse 42 Schematic of Liquid Dominated 2342
Radiation) Single Flash Steam System
(Geothermal Principle)
09 Pyrheliometer (For measuring 2309
beam radiation) 43 Schematic of a Binary Fluid 2343
Geothermal Power System
10 Sunshine Recorder 2310
44 Schematic of Liquid Dominated 2344
11 Set up for testing liquid flat plate 2311 Total Flow Concept
collector
45 Schematic of Geothermal 2345
12 Types of Concentrating 2312 Preheat Hybrid System
collectors
46 Schematic of Fossil Super Heat 2346
13 Solar Water heating systems 2313 Hybrid System
14 Solar Space heating systems 2314 47 Schematic of Regenerative Fuel 2347
15 Solar Pond Electric Power Plant 2315 Cell
16 Solar Cookers 2316 48 Steam Gasification Process And 2348
17 Types of Bio-Gas Plant 2317 its Application
18 Geothermal Energy 2318 49 Principles of MHD Power 2349
Generation
19 Wave Energy 2319
20 Solar Spectrum out side the 2320 50 Simple MHD Generator Cycle 2350
Atmosphere & at Ground Level (Closed Cycle)
21 A Schematic of a turbine Driven 2321 51 Schematic of MHD Power Cycle 2351
Pump using solar energy (Closed Cycle)
22 Schematic of OTEC Open Cycle 2322 52 Schematic of An Open Cycle 2352
23 Schematic of OTEC Close Cycle 2323 MHD Generator
24 Schematic of OTEC Close 2324 53 Schematic of a Close Cycle 2353
Ammonia Cycle MHD Generator
25 Schematic of OTEC Hybrid 2325 54 Cabinet Dryer 2354
Cycle 55 Types of Solar Collectors 2355
26 Schematic of Tidal Power House 2326 56 Industrial Solar Water Heating 2356
27 Tidal Power Plant (Single Basin 2327 System (Close And Open Loop
Operation) Configureation)
28 Tidal Power Plant (Double Basin 2328 57 Schematic Diagram a Space 2357
Operation) Heating System using Liquid
Flat Plate
29 Schematic of Single Process 2329
Conversional Digester (Biogas) 58 Schematic Diagram of a Space 2358
Heating System Using Solar Air
30 Schematic of Two Stage 2330 Heater
Digestion Process
59 Low Temperature Power 2359
31 Bio-Gas Plant Floting Gas 2331 Generation Cycle Using Flat
Holder Plate Collector
32 Common Circular Fixed Dome 2332 60 Medium Temperature Power 2360
Digestor Generation Cycle Using
33 Domestic Bio-Gas Plant 2333 Parabolic Concentrating
34 Possible Energy Conversion 2334 Collectors
Routes And Products from Bio- 61 Central Receiver Power Plant 2361
Mass (Solar)
35 Schematic of an Updraft Gasifier 2335 62 Schematic of Solar Absorption 2362
Refrigeration System
63 Box System Cooker with One 2363
Reflector
65 Solar Power Plant 2365
64 Solar Water Still 2364
Top

HYDRAULICS & PNEUMATICS ( HYDRAULICS ) (HP-2401 )

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Flow Control In Hydraulic 2401 10 Direction Control in Hydraulic 2410
Circuits-I Circuits-II
02 Flow Control In Hydraulic 2402 11 Direction Control in Hydraulic 2411
Circuits-II Circuits-III
03 Flow Control In Hydraulic 2403 2403 12 Direction Control in Hydraulic 2412
Circuits-III 2412 Circuits-IV
04 Flow Control In Hydraulic 2404 13 Direction Control in Hydraulic 2413
Circuits-IV Circuits-V
05 Pressure Control in Hydraulic 2405 14 Direction Control in Hydraulic 2414
Circuits-I Circuits-VI
06 Pressure Control in Hydraulic 2406 15 Direction Control in Hydraulic 2415
Circuits-II Circuits-VII
07 Pressure Control in Hydraulic 2407 16 Various Types of Pump (Gear 2416
Circuits-III Pump)
08 Pressure Control in Hydraulic 2408 17 Air Generation & Distribution 2417
Circuits-IV System
09 Direction Control in Hydraulic 2409
2409 Circuits-I

HYDRAULICS & PNEUMATICS ( PNEUMATICS ) (HP-2451)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Filter, Regulator, Lubricator 2451 11 Types of Seat Valve 2461
02 Single Acting Cylinder 2452 12 Types of Spool Valve 2462
03 Double Acting Cylinder 2453 13 Manual And Mechanical 2463
04 Double Acting Cylinder (With 2454 Actuation Valves
Tie Rod) 14 Pilot Operated D.C. Valve 2464
05 Types of Double Acting 2455 15 Impulse Generator 2465
Cylinder 16 Types of Flow Control Valve 2466
06 Cushion Assembly 2456 17 Quick Exhaust Valve 2467
07 Air Motor 2457 18 Time Delay Valve & Shuttle 2468
08 Pneumatic Tools 2458 Valve
09 Directional Control Valve 2459 19 Twin Pressure Valve 2469
10 Comparision of Seat Valves & 2460 20 Solenoid Operated Valve 2470
Spool Valves
 Instrumentation (INS - 2501)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Modern Radiation Detectors 2501 07 Installation and Testing of 2507
02 matography 2502 Process Loops
03 Instrumentation Flow Sheet 2503 06 Instrumentation Diagram of 2506
Symbols (I) Various Loops
04 Instrumentation Flow Sheet 2504 08 Ups-block Diagram 2508
Symbols (II) 09 Ups Circuit Diagram 2509
05 Instrumentation Flow Sheet 2505
Symbols (III)
COMPUTER AIDED DESIGN & COMPUTER AIDED MANUFACTURING
(CAD / CAM-1101)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.

01 Product Cycle Comparison 1151 11 Opitz System 1161

02 CAD Process 1152 12 Retrival CAPP System 1162

03 Relationship of CAD / CAM 1153 13 Types of CIMS 1163

04 Types of C.N.C. 1154 14 Activities in CIPMS 1164

05 N.C. & N. C. Part Programming 1155 15 Structure of MRPS 1165

06 A. P. T. 1156 16 Shop Floor Control System 1166

07 Types of D.N.C. 1157 17 Level Scanning in CPM 1167

08 Robot Physical Configuration 1158 18 Computer Process Interface 1168

09 Basic Robot Motions 1159 19 Hierarchy in CIMP 1169

10 W/P Layout of Robot 1160 20 D.D.C. & Relation with A.C. 1170

Top
 PERSONAL COMPUTER
(PCS -2701)

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.

01 Personal Computer 2701 25 Comparison of CD Rom & DVD Rom 2725

02 Central Processing Unit 2702 26 Comparitive Characteristics of 2726

Memories
03 Cut Sectional View of C.P.U. 2703
27 Magnetic Tape Recording 2727
04 Key Board 2704
28 CD Rom & DVD Rom 2728
05 Instruction for failure of P.C. 2705
29 A Floppy Disk 2729
06 Some Functions of Keys 2706
30 A Magnetic Disk Memory 2730
07 Some Important D.O.S. 2707
31 Defining Access Time & Write Time 2731
08 D.O.S. Commands-II 2708 in a Memory

09 Summary of D.O.S. Commands-I 2709 32 Illustrating Memory Interleaving 2732

10 Summary of D.O.S. Commands-II 2710 33 Details of Processor to I/O 2733

Communication
11 Wordstar Commands-I 2711
34 Illustrating Interconnection of 2734
12 Wordstar Commands-II 2712 Computer Units V/A Two Systems
Buses
13 Summary of Wordstar Commands 2713
35 PCB Peripheral Control Bus 2735
14 Cursor movements & Editing Keys 2714
36 A Unibus Connection of Units 2736
15 Lotus Basic 2715
37 Illustrating use of a Cache Memory 2737
16 Lotus Commands-I 2716
38 ABCII Code for Characters 2738
17 Lot us Commands-II 2717
 39 Binary Hexadecimal & Decimal 2739
Equivalents
18 Foxpro / Data Base Commands 2718
40 A Binary Addition Table 2740
19 Computer Generation (A 2719
Comparison) 41 Two's Complement Representation 2741
of Numbers
20 Basic Organisations of a Computer 2720
System 42 A Machine Language Program for 2742
HYP Com.
21 Comparison of Printers 2721
43 Layers of Unix Operating Systems 2743
22 An Assembly Program & Machine 2722
Language Equivalent 44 Diagrammatic Representation of 2744
Sound Card
23 A Memory Cell using Controlled 2723
Switches 45 Unix Commands 2745

24 Recording on a Magnetic Surfaces 2724 46 Sound Card 2746

47 An Oracle Instance 2747

48 VGA Connector Pin Configuration 2748

Machinist

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Shaping Machine 18 Elements of Jig and Fixture - I
02 Hydraulic Shaper Mechanism 19 Elements fo Jig and Fixture - II
03 Shaping Operations 20 Types of Gauge
04 Slotting Machines 21 Dial Gauge Indicator
05 Planning Machines 22 Quick Return Mechanism
06 Planning Operations 23 Feed Mechanism
07 Types of Milling Machine 24 Cutting Tool ( Shaping )
08 Milling Operations - I 25 Slotting Machine Tools
09 Milling Operations - II 26 Slotting Machine Mechanism
10 Types of Milling Cutter ( Whitworth )
11 Elements of Milling Cutter 27 Planing Cutting Tools
12 Types of Clarnp 28 Dividing Head
13 Universal Dividing Head 29 Gear Tooth Vernier Caliper
14 Measuing Instruments 30 Cam and Cam Profile
15 Vernier Micromerter 31 Combination Set
16 Vernier Caliper 32 Broaching Machine
17 Vernier Hight/ Depth Gauge 33 Planer feed machanism

MACHANIST GRINDER

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Precision Instruments 11 Cylinderica1 Grinding Machine
02 Types of Drill, Tap 12 Surface Frinding Machine
03 DrillingMachine 13 Centreless Grinding Wheel
04 Centre Lathe 14 Types of Grinding Wheel
05 Lathe Tools 15 Grinding Operations
06 Measuring Instruments (Cylinderical )
07 Types of Dresser 16 Standard Marking System (I.S.I.)
08 Lathe Operations 17 Wheel Mounting Methods
09 Outside Micrometer 18 Limit Gauge Tolerance
10 Vernier Caliper 19 Types of Gauges
20 Wheel Balancing

FITTER

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Blast Furnace 23 Types of Thread
02 Cupola Furnace 24 Fasteners
03 Furnace (Beasemer / Open 25 Rivets and Joints
Hearth / Elect.) 26 Typpes of Washer, Screw, Nut
04 Layout Equipment and Bolt - I
05 Marking Tools 27 Typpes of Washer, Screw, Nut
06 Surface Gauge and Bolt - II
07 Types of Punches 28 Measuring Instruments
08 Combination Set 29 Vernier Micrometer
09 Types of Vice - I 30 Vernier Caliper
10 Types of Vice - II 31 Vernier Hight and Depth Gauge
11 Types of File 32 Dial Gauge
12 Types of Harnmer 33 Straight Edges and Trysqure
13 Types of Chiesel and Operation 34 Types of Gauge
14 Hacksaw Machine 35 Limit, Fit and Tolerance
15 Hacksaw and Operation 36 Types of Jig and Fixture - I (Box
Type)
16 Types of Drill
37 Types of Jig and Fixture - II
17 File Operation (Open Type)
18 Types of Drill Machine 38 Centrifugal Casting
19 Types of Scraper 39 Electric Arc-Furnace
20 Hand Tools 40 Type of wrench
21 Types of Reamer 41 Cutting Thread with Die stock
22 Tapping 42 Rivetting process
43 Pipe fitting

TURNER

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Centre Lathe 20 Vernier Hight Gauge
02 Capsten Lathe 21 Vernier Caliper
03 Turret Lathe 22 Marking Tools
04 Lathe Parts 23 Limit, Fit, tolerance
05 Feed Mechanism 24 Cutting Speed and Feed
06 Tool Post 25 Combination Set
07 Tail Stock 26 Types of Reamer
08 Collet Chuck 27 Indication of Surface Roughness
09 Mandrel 28 Types of Bolt, Nut, Washer,
10 Taper Turning Attachment Screw-I
11 Cutting Tool 29 Types of Bolt, Nut, Washer,
Screw-II
12 Tool Geometry - I
30 Types of Key
13 Tool Geometry - II
31 Elements of Jig and Fixture - I
14 Types of Chip and Chip Breaker
32 Elements of Jig and Fixture - II
15 Lathe Operations
33 The effect of Incorrect tools
16 Standard Tapers seting (for plain & Taper
17 Types of Thread Turning)
18 Measuring Instruments 34 Uses of Sine Bar
19 Vernier Micrometer 35 Sleep Gauges
36 Lubricating Systems
37 Types of Gauge

PATTERN MAKER

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Measuring Tools 14 Types of Pattern
02 Types of Saw 15 Types of Core Print
03 Marking & Measuring Tools 16 Types of Dowell
04 Drilling Tools 17 Circular Saw Machine
05 Types of File 18 Band Saw Machine
06 Impelling Tools 19 Plaining Machine
07 Clamping Tools 20 Sanding Machine
08 Types of Emery Stone 21 Grinding Machine
09 Fasteners 22 Disc Sander Machine
10 Types of Wood 23 Jig Saw Mahine
11 Pattern Lay Out 24 Skeleton Pattern
12 Types of Fillet 25 Master Patterrn
13 Types of Pin

CARPENTER
Sr. Name of Chart Code Sr. Name of Chart Code
No. No. No. No.
01 Meesuring Tools 14 Circular Saw Machine
02 Types of Saw 15 Band Saw Machine
03 Marking & Measuring Tools 16 Plaining Machine
04 Drilling Tools 17 Sanding Machine
05 Types of File 18 Frinding Machine
06 Impelling Tools 19 Disc Sander Machine
07 Clamping Tools 20 Jig Saw Machine
08 Types of Emery Stone 21 Master Pattern
09 Fasteners 22 Carpentry Chisel
10 Types of Wood 23 Carpentry Braces
11 Pattern Layout 24 Carpentry Planes
12 Types of Core Print 25 Skeleton Pattern
13 Types of Dowell

BLACK SMITHY

Sr. Name of Chart Code Sr. Name of Chart Code

No. No. No. No.
01 Smith's Hearth 11 Double Column Steam Hammer
02 Smith's Anvil 12 Hand Forging Operations
03 Blacksmith's Swages 13 Smithy Tools
04 Blacksmith's Chisels 14 Single Columnsteam Hammer
05 Blacksmith's Fullers 15 Spring Hammer
06 Blacksmith's Tongs 16 Pneumatic Hammer
07 Flatters and Set Hammers 17 Steam Drop Hammer
08 Blacksmith's Hammers 18 Counter Blow Steam Hammer
09 Punches and Drifting 19 Working Principles of Steam Air
10 Blacksmith's Welds Hammer
20 Types of Press