Scribd
Upload
37 views

CSWP

The CSWP exam is designed to test SolidWorks skills and consists of 3 segments totaling 3 hours and 20 minutes. The exam focuses on hands-on challenges in areas like part and assembly modeling, configurations, mates, and mass properties. It is aimed at SolidWorks users like engineers and designers seeking to demonstrate their expertise. Passing scores differ by segment but require skills in areas such as creating parts from drawings, equations, configurations, assemblies, mates and more. The exam allows re-testing every 14 days for a fee.

Uploaded by

jabe
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
37 views

CSWP

The CSWP exam is designed to test SolidWorks skills and consists of 3 segments totaling 3 hours and 20 minutes. The exam focuses on hands-on challenges in areas like part and assembly modeling, configurations, mates, and mass properties. It is aimed at SolidWorks users like engineers and designers seeking to demonstrate their expertise. Passing scores differ by segment but require skills in areas such as creating parts from drawings, equations, configurations, assemblies, mates and more. The exam allows re-testing every 14 days for a fee.

Uploaded by

jabe
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

SOLIDWORKS Exam

CSWP

Who should attend: Introduction

SolidWorks Users
R&D engineer SOLIDWORKS certifications are a benchmark to measure your knowledge and competency
Application engineer with SOLIDWORKS software. A certification helps you to stand out from the crowd and
Product designer or showcases your expertise to businesses professionals alike – a valuable asset in a
engineer competitive job market.
Industrial engineer

Prerequisites: Objective
Attended SOLIDWORKS
Essentials Course
At the end of this program participants are expected to:

Attended Advance Part  Get formal recognition of achievement.


Modeling Course  Online certificate access.
 Professional credibility with proven engineering competencies.
Attended Advance  Membership to the community CSWP
Assembly Modeling
Course

Basic understanding of
Re-test Policy:
part design and drafting
There is a minimum 14 day waiting period between every attempt of the same CSWP
Duration:
Segment exam. Also, an exam credit for that CSWP Segment must be purchased for each
3 hours 20 minutes
exam attempt.
Segment 1: 70 min
Segment 2: 50 min
Segment 3: 80 min

Methodology:

Practical hands-on with


using computers and
case studies

IME CADCAM TRAINING CENTRE SDN BHD


PJ: 22A, Jln. PJS 1/46, Tmn. Petaling Utama, 46000 PJ, Selangor, Malaysia.
Tel: +603-7783 6866 | Fax:+603-7783 4384
PG: 68, Jln. Perai Jaya 4, Bandar Perai Jaya, 13700 Pulau Pinang, Malaysia.
Tel: +604-399 5571 | Fax: +604-399 5572
JB: No. 25-01, Jalan Bestari 8/2, Taman Nusa Bestari, 79150, Iskandar Puteri, Johor.
Tel: +607-238 7978 | Fax: +607-238 2162

[email protected] | www.cadcam.com.my
SOLIDWORKS Exam
CSWP

SOLIDWORKS
CSWP
Key Topics Day 1

Exam features hands-on challenges in these areas:

Total Exam Length: 3 hours 20 minutes (All segments)

Segment 1: (70 Minutes) - 75 points to pass/105 points maximum

 Creating a part from a drawing


 Using linked dimensions and equations to aid in modeling
 Using equations to relate dimensions
 Updating parameters and dimension sizes
 Mass property analysis
 Modifying geometry on initial part to create a more complex part
 Modifying parameters on the part at different stages while maintaining all other
dimensions and design intent

Segment 2: (50 Minutes) - 77 points to pass/104 points maximum

 Creating configurations from other configurations


 Changing configurations
 Creation of configurations using a Design Table
 Mass properties
 Changing and/or rearranging features of an existing SOLIDWORKS part

Segment 3: (80 Minutes) - 77 points to pass/109 points maximum

 Creating an assembly
 Adding parts to an assembly
 Doing collision detection when moving a part in an assembly
 Interference detection
 Basic and advanced mates
 Rigid and Flexible subassemblies
 Replacing a part with another part in an assembly
 Creating a coordinate system
 Using a coordinate system to perform mass properties analysis

IME CADCAM TRAINING CENTRE SDN BHD


PJ: 22A, Jln. PJS 1/46, Tmn. Petaling Utama, 46000 PJ, Selangor, Malaysia.
Tel: +603-7783 6866 | Fax:+603-7783 4384
PG: 68, Jln. Perai Jaya 4, Bandar Perai Jaya, 13700 Pulau Pinang, Malaysia.
Tel: +604-399 5571 | Fax: +604-399 5572
JB: No. 25-01, Jalan Bestari 8/2, Taman Nusa Bestari, 79150, Iskandar Puteri, Johor.
Tel: +607-238 7978 | Fax: +607-238 2162

[email protected] | www.cadcam.com.my

You might also like