Scribd
Upload
11 views

Assembly Code

This document configures a microcontroller to measure distance using ultrasonic sensing. It initializes ports for outputting trigger pulses and reading echo signals. A timer is used to measure the echo pulse width, with the count stored after each echo and displayed on seven-segment LEDs. The value is divided and displayed digit-by-digit across three LEDs to show the distance measured.

Uploaded by

abdul nurudeen
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
11 views

Assembly Code

This document configures a microcontroller to measure distance using ultrasonic sensing. It initializes ports for outputting trigger pulses and reading echo signals. A timer is used to measure the echo pulse width, with the count stored after each echo and displayed on seven-segment LEDs. The value is divided and displayed digit-by-digit across three LEDs to show the distance measured.

Uploaded by

abdul nurudeen
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

ORG 00H // origin

MOV DPTR,#LUT // moves the address of LUT to DPTR


MOV P1,#00000000B // sets P1 as output port
MOV P0,#00000000B // sets P0 as output port
CLR P3.0 // sets P3.0 as output for sending trigger
SETB P3.1 // sets P3.1 as input for receiving echo
MOV TMOD,#00100000B // sets timer1 as mode 2 auto reload timer
MAIN: MOV TL1,#207D // loads the initial value to start counting from
MOV TH1,#207D // loads the reload value
MOV A,#00000000B // clears accumulator
SETB P3.0 // starts the trigger pulse
ACALL DELAY1 // gives 10uS width for the trigger pulse
CLR P3.0 // ends the trigger pulse
HERE: JNB P3.1,HERE // loops here until echo is received
BACK: SETB TR1 // starts the timer1
HERE1: JNB TF1,HERE1 // loops here until timer overflows (ie;48 count)
CLR TR1 // stops the timer
CLR TF1 // clears timer flag 1
INC A // increments A for every timer1 overflow
JB P3.1,BACK // jumps to BACK if echo is still available
MOV R4,A // saves the value of A to R4
ACALL DLOOP // calls the display loop
SJMP MAIN // jumps to MAIN loop

DELAY1: MOV R6,#2D // 10uS delay


LABEL1: DJNZ R6,LABEL1
RET

DLOOP: MOV R5,#100D // loads R5 with 100D


BACK1: MOV A,R4 // loads the value in R4 to A
MOV B,#100D // loads B with 100D
DIV AB // isolates the first digit
SETB P1.0 // activates LED display unit D1
ACALL DISPLAY // calls DISPLAY subroutine
MOV P0,A // moves digit drive pattern for 1st digit to P0
ACALL DELAY // 1mS delay
ACALL DELAY
MOV A,B // moves the remainder of 1st division to A
MOV B,#10D // loads B with 10D
DIV AB // isolates the second digit
CLR P1.0 // deactivates LED display unit D1
SETB P1.1 // activates LED display unit D2
ACALL DISPLAY
MOV P0,A // moves digit drive pattern for 2nd digit to P0
ACALL DELAY
ACALL DELAY
MOV A,B // moves the remainder of 2nd division to A
CLR P1.1 // deactivates LED display unit D2
SETB P1.2 // activates LED display unit D3
ACALL DISPLAY
MOV P0,A // moves the digit drive pattern for 3rd digit to P0
ACALL DELAY
ACALL DELAY
CLR P1.2 // deactivates LED display unit D3
DJNZ R5,BACK1 // repeats the display loop 100 times
RET

DELAY: MOV R7,#250D // 1mS delay


LABEL2: DJNZ R7,LABEL2
RET

DISPLAY: MOVC A,@A+DPTR // gets the digit drive pattern for the content in A
CPL A // complements the digit drive pattern (see Note 1)
RET
LUT: DB 3FH // look up table (LUT) starts here
DB 06H
DB 5BH
DB 4FH
DB 66H
DB 6DH
DB 7DH
DB 07H
DB 7FH
DB 6FH
END

You might also like