Scribd
Upload
4K views

BM Improper Detection of DTC B108E 04 (Center Display Internal Malfunction)

This service information from Mazda concerns a diagnostic trouble code (DTC) B108E:04 that may be improperly detected in some Mazda3 vehicles with a center display. The DTC indicates an internal malfunction of the center display, but may occur without any actual malfunction. If the DTC is present without issues, no further diagnosis is needed and the vehicle can be returned to the customer. A software update was implemented to optimize detection of this DTC. Technicians can check the software version using the diagnostic assist function to determine if a vehicle has the update.

Uploaded by

Jack Darmawan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
4K views

BM Improper Detection of DTC B108E 04 (Center Display Internal Malfunction)

This service information from Mazda concerns a diagnostic trouble code (DTC) B108E:04 that may be improperly detected in some Mazda3 vehicles with a center display. The DTC indicates an internal malfunction of the center display, but may occur without any actual malfunction. If the DTC is present without issues, no further diagnosis is needed and the vehicle can be returned to the customer. A software update was implemented to optimize detection of this DTC. Technicians can check the software version using the diagnostic assist function to determine if a vehicle has the update.

Uploaded by

Jack Darmawan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Service Information 3-1, Shinchi, Fuchu-cho, Aki-gun

Hiroshima 730-8670, Japan


TEL : 81(82)287-5323
FAX : 81(82)287-5220

Category Ref. No. Page


T Technical E006/14 1 of 2
Coverage Date Issued
Distributor only Please inform your dealers March 5, 2014
Please convey this information to your Director General Manager Date Revised
Warranty Dept. Parts Dept. Training Dept. Field Rep.
Applicable Model Applicable Countries or Specifications

Mazda3 (BM) with Center Display Worldwide

Subject: Improper Detection of DTC B108E:04 (Center Display Internal


Malfunction) without any malfunction
DESCRIPTION
This Service Information is to advise dealers about the following service note for the DTC B108E:04
which may be stored in the memory and found during normal service operation.
B108E:04 Center display internal malfunction
If this DTC is stored without any malfunction of the center display or connectivity master unit (CMU),
it is not necessary to attempt any further diagnosis/repair and the vehicle can be returned to the
customer as it is. (You can clear the DTC but it may be stored again.)
Even if this DTC is stored, the customer will not notice it as no related warning light or message is
displayed.

CAUSE
Too sensitive detection condition of DTC 108E:04.

MASS PRODUCTION CHANGE


Software of the center display has been changed to optimize the detection condition.

BEGINNING VIN & DATE OF MODIFICATION

US Spec.
From JM1BM**** ** 161015 December 14, 2013
EC Spec.
From JMZBM**** ** 132260 December 14, 2013
Israel Spec.
From JMZBM**** ** 104607 December 14, 2013
ADR Spec.
From JM0BM**** ** 104607 December 14, 2013
General Spec.
From JM6BM**** ** 104607 December 14, 2013
From JM7BM**** ** 104607 December 14, 2013

REFERENCE

The software version can be determined by using the diagnostic assist function [CONNECTIVITY
MASTER UNIT] as follows. By doing so it can be confirmed if the software level is before or after the
change.
E006/14
Page 2 of 2
Confirmation procedure of software version

1. Activate the diagnostic assist function of CONNECTIVITY MASTER UNIT according to the
activation procedure. (See Activation Procedure in the workshop manual “DIAGNOSTIC
ASSIST FUNCTION [CONNECTIVITY MASTER UNIT].)

2. Input Diagnostic Assist Code “68” according to the procedure. (See “Diagnostic Assist Code
Input Procedure” in the workshop manual “DIAGNOSTIC ASSIST FUNCTION
[CONNECTIVITY MASTER UNIT].)

3. Confirm the software version displayed on the TFT LCD screen.


The software version is BHP1_A_0006 or older. : Before modification
The software version is BHP1_A_0007 or later. : After modification
4. Cancel the diagnostic assist function according to the ending procedure. (See “Ending
Procedure” in the workshop manual “DIAGNOSTIC ASSIST FUNCTION [CONNECTIVITY
MASTER UNIT].)

Ryu Shimizugawa
Manager, Technical Information Gr.
Technical Service Dept.
Mazda Motor Corporation
2DA1705942 (MC Internal Use)

You might also like