db: DB is moved to USER Menu

A1HY: A1HY is moved to USER

Quick Operation Manual 2.2.3 Alarm Menu 2.2.4 Event Input Menu 2.2.5 User Select 3. PARAMETERS DESCRIPTION: Menu
For PID + Fuzzy Logic Process Controller (ALRM): Use or (EI): Use or key to Menu (SEL): Use or Modbus
Parameter Parameter
Select BPLS (Bumpless NoNE: No alarm function A1SP: A1SP is moved to USER
Register Range Output 2 failure transfer),or 0.0 ~ 100.0 % to dtMR: Dwell timer action Menu
Model: C22/C62/C82/C83/C72/C42/R22 key to get ALRM in get EI in the lower key to get SEL in Address
Notation Description 30 O2FT
transfer mode continue output 2 control function [Link]: Deviation high alarm
Select 1st~8th
A1dV: A1DV is moved to USER
95~102 SEL1~8 parameter for user
Ver. UMQOC621B the lower display, display, then use key the lower display, then 0 SP1 Set Point 1 Low: SP1L High: SP1H if the sensor fails [Link]: Deviation low alarm Menu
1. DISPLAY AND KEYS menu
then use key to to enter event input use key to enter user 1 SP2 Set Point 2 Low: SP1L High: SP1H 31 CYC2 Output 2 cycle time Low: 0.1 High: 90.0 sec. [Link]: Deviation band out of A2HY: A2HY is moved to USER
2 SP3 Set Point 3 Low: SP1L High: SP1H Cooling proportional Alarm 4 function for band alarm Menu
enter alarm menu menu parameters. select menu parame- 3 SP4 Set Point 4 Low: SP1L High: SP1H
32 CPB
band value
Low: 50 High: 300 % 55 A4FN
alarm output [Link]: Deviation band in band A2SP: A2SP is moved to USER
parameters. ters. Up to 8 parame- 4 SP5 Set Point 5 Low: SP1L High: SP1H Heating-cooling alarm Menu
or or ters by selecting 5 SP6 Set Point 6 Low: SP1L High: SP1H
33 DB
dead band
Low: - 36.0 High: 36.0 %
[Link]: Process value high alarm A2dV: A2DV is moved to USER
SET ALRM SET EI 6 SP7 Set Point 7 Low: SP1L High: SP1H [Link]: Process value low alarm
SEL1~SEL8 can be put (negative value= Menu
Dwell timer overlap) [Link]: Heater break alarm A3HY: A3HY is moved to USER
in the User Menu. output time NoNE: No alarm function [Link]: Heater short alarm Menu
7 DTMR Low: 0.0 High: 4553.5
A1FN (Minute: dtMR: Dwell timer action NoRM: Normal alarm action A3SP: A3SP is moved to USER
E1FN
A1MD or Seconds) [Link]: Deviation high alarm LtCH: Latching alarm action Menu
A1HY SP2
SET SEL Alarm 4 operation
J_tC: J type Thermocouple [Link]: Deviation low alarm 56 A4MD HoLd: Hold alarm action A3dV: A3DV is moved to USER
A1FT E2FN mode
A1SP K_tC: K type Thermocouple [Link]: Deviation band out of [Link]: Latching & Hold action Menu
SP3
A1DV T_tC: T type Thermocouple Alarm 1 function for band alarm [Link]: Set point holding alarm A4HY: A4HY is moved to USER
E3FN
A1DL E_tC: E type Thermocouple 34 A1FN
SP4 alarm 1 output [Link]: Deviation band in band Hysteresis control Low: 0.1°C Menu
A2OT
B_tC: B type Thermocouple 57 A4HY
A2FN E4FN SEL1 alarm of alarm 4 High: 50.0°C(90.0°F) A4SP: A4SP is moved to USER
SP5 SEL2 R_tC: R type Thermocouple OFF: Alarm output OFF if sensor Menu
A2MD [Link]: Process value high alarm
A2HY E5FN SEL3 S_tC: S type Thermocouple A4dV: A4DV is moved to USER
[Link]: Process value low alarm Alarm 4 failure fails
A2FT SP6 N_tC: N type Thermocouple 58 A4FT
A2SP
SEL4 [Link]: Heater break alarm transfer mode ON: Alarm output ON if sensor Menu
E6FN L_tC: L type Thermocouple
A2DV SEL5 [Link]: Heater short alarm fails PL1L: PL1L is moved to USER
A2DL
SP7 Input sensor U_tC: U type Thermocouple
SEL6 8 INPT NoRM: Normal alarm action 59 A4SP Alarm 4 set point Low: -19999 High: 45536 Menu
A3OT selection P_tC: P type Thermocouple
During power-up, the upper display will show PROG and the lower display will A3FN
SEL7
C_tC: C type Thermocouple Alarm 1 operation
LtCH: Latching alarm action
60 A4DV
Alarm 4 deviation
Low: -19999 High: 45536
C82/C83/C72/C42:
SEL8 value NoNE: Not selected
show the Firmware version for 6 seconds. A3MD
D_tC: D type Thermocouple
35 A1MD
mode
HoLd: Hold alarm action
R485: RS-485 and Remote SP
A3HY [Link]: Latching & Hold action Bumpless transfer
SCROLL/ENTER KEY: to select a parameter to be viewed or adjusted. A3FT
[Link]: PT100 Ω DIN curve
[Link]: Set point holding alarm
61 BPL1
value of MV1
Low: 0.00 High: 100.00
C62:
[Link]: PT100 Ω JIS curve
Press for next parameter. Press and key for return to previous parameter. A3SP
A3DV 4-20: 4-20mA linear current input Hysteresiscontrol of Low: 0.1°C Bumpless transfer NoNE: Not selected
36 A1HY 62 BPL2 Low: 0.00 High: 100.00
UP KEY: This key is used to increase the value of the selected parameter. A3DL
A4OT 2.2.7 Current or 0-20: 0-20mA linear current input alarm 1 High: 50.0°C(90.0°F) value of MV2 R485: RS-485
SET Ct OFF: Alarm output OFF ifsensor Sense voltage C22/R22:
DOWN KEY: This key is used to decrease the value of the selected parameter. A4FN
Transformer Input
0-5V: 0-5VDC linear voltage input
Alarm 1 failure fails 63 CJCL during cold junction Low: 0 High: 7552 NoNE: Not selected
1-5V: 1-5VDC linear voltage input
RESET KEY: This key is used to: A4MD
A4HY Menu (Ct): Use 0-10: 0-10VDC linear voltage input
37 A1FT
transfer mode ON: Alarm output ON if sensor calibration low R485: RS-485
[Link] the display to the home screen. A4FT
or key to get Ct HBEN oC: °C unit fails 64 PV64 Process value Low: -19999 High:45536
Option function 1
EI1: Event 1 input
A4SP Input unit 103 OFS1 CT1: CT 1 input
[Link] a latching alarm once the alarm condition is removed. A4DV
in the lower display,
HBHY 9 UNIT
selection
oF: °F unit 38 A1SP Alarm 1 set point Low: -19999 High: 45536
65 SV65
Current set point
Low: SP1L High:SP1H selection
HB1T Pu: Process unit Alarm 1 deviation value 4-20: 4-20mA retransmission
[Link] manual control mode, auto-tuning mode or calibration mode. A4DL
then use key to HB2T
[Link]: No decimal point
39 A1DV
value
Low: -19999 High: 45536
MV1 Output 1 output
[Link] an auto-tuning or communication error message. enter current
HSEN
HSHY Decimal point 1-dP: 1 decimal digit ALM: Alarm 2 output 1
66
66 %Value(Heating)
Low: 0.00 High: 100.00 % 0-20: 0-20mA retransmission
10 DP 40 A2OT Alarm 2 Output
[Link] the dwell timer when the dwell timer has timed out. 2.2.6 Communication transformer input HS1T selection 2-dP: 2 decimal digit RALM: Reverse Alarm 2 Output
67
MV2 Output 2
Low: 0.00 High: 100.00 %
output
HS2T 3-dP: 3 decimal digit 0-5V: 0-5VDC retransmission
[Link] the manual control menu if failure mode occurs. Menu (CoMM): Use menu parameters. Input low
NoNE: No alarm function 67 %Value(Cooling)
output
dtMR: Dwell timer action Remaining time of
2. MENU FLOWCHART: or key to get CoMM
11 INLO
scale value
Low: -19999 High:45536
[Link]: Deviation high alarm
68 TIMER
dwell timer
Low: 0.0 High: 4553.6 1-5V: 1-5VDC retransmission
Input high [Link]: Deviation low alarm output
in the lower display, 2.2.8 Profile Menu (PRoF): Use or key to 12 INHI
scale value
Low:INLO+50 High:45536 69 EROR Error code Low: 0 High: 65535
0-10: 0-10VDC retransmission
[Link]: Deviation band out of Operation mode &
then use key to get PRoF in the lower display, then use key Low limit of band alarm
70 MODE
alarm status
Low: 0 High: 65535 output
enter communication to enter profile menu parameters. 13 SP1L set point Low: -19999 High :45536 [Link]: Deviation band in band C22:[Link] C62:[Link] C82/C83/C72/C42:
5 Sec 6.2 Sec 7.4Sec 8.6Sec 9.8 Sec value NoNE: Not selected
menu parameters. High limit of 41 A2FN
Alarm 2 function for alarm
71 PROG71 Program code
C82:[Link] C83:[Link]
CT1: CT1 input and Remote SP
alarm 2 output [Link]: Process value high alarm C72:[Link] C42:[Link]
or
14 SP1H set point Low: SP1L High:45536 [Link]: Process value low alarm CT1.2: CT1,CT2 inputs and
SET PRoF R22:[Link]
or value [Link]: Heater break alarm Remote SP
5 Sec 5 Sec 5 Sec 72 CMND Command code Low: 0 High: 65535
0: 0 second time constant C62:
SET CoMM [Link]: Heater short alarm 73 JOB1 Job code Low: 0 High: 65535
0.2: 0.2 second time constant E1.C.o: Event Input 1 Control NoNE: Not selected
User Menu Setup Menu Manual Menu Auto-Tuning Menu Calibration Menu 74 JOB2 Job code Low: 0 High: 65535
0.5: 0.5 second time constant
SCROLL/ENTER KEY: PROF
RMPU
TSP7
RPT7 Filter 1: 1 second time constant
Alarm Output 75 JOB3 Job code Low: 0 High: 65535
EI1.2: Event input 1 and Event
E2.C.o: Event Input 2 Control input 2
1. Press and hold for 5 seconds, display will show . Press to enter STAR SKT7 damping time 2: 2 second time constant
Alarm Output 76 CJCT
Cold Junction
Low: -4000 High: 9000 [Link]: Event input 1 and CT2
15 FILT Temperature
the Setup Menu. ADDR END
PFR
TSP8
RPT8
constant of 5: 5 second time constant
NoRM: Normal alarm action mV calibration low
input
BAUD PV 10: 10 second time constant
2. Press and hold for 6.2 seconds, display will show . Press and hold HBLO SKT8
20: 20 second time constant Alarm 2 operation
LtCH: Latching alarm action 77 ADLO
coefficient
Low: -1999 High: 1999 CT1.2: CT1 and CT2 inputs
DATA C22:
for 5 seconds to enter Manual Mode. HBHI TSP9
30: 30 second time constant
42 A2MD
mode
HoLd: Hold alarm action
78 ADHI
mV calibration high
Low: -1999 High: 1999 NoNE: No selected
PARI HBT RPT9 [Link]: Latching & Hold action
3. Press and hold for 7.4 seconds, display will show . Press and hold STOP CYCL SKT9
60: 60 second time constant
[Link]: Set point holding alarm
coefficient
4-20: 4-20mA retransmission
None: No Display RTD calibration low
for 5 seconds to enter Auto-Tuning Mode. CYCR TSPA
MV1: Display MV1 (66/130)
Hysteresis control Low: 0.1°C 79 RTDL
coefficient
Low: -1999 High: 1999 output
STEP RPTA 43 A2HY 0-20: 0-20mA retransmission
4. Press and hold for 8.6 seconds, display will show . Press and hold TIMR SKTA
MV/TIME
MV2: Display MV2(67/131)
of alarm 2 High: 50.0°C(90.0°F)
RTD calibration
16 DISP display OFF: Alarm output OFF ifsensor 80 RTDH Low: -1999 High: 1999 output
for 2~3 seconds to enter Calibration Mode. STAT TSPB
selection
tIMR: Display Time (68)
Alarm 2 failure fails
high coefficient
0-5V: 0-5V retransmission
TSP1 RPTB PRoF: Display STAT(162) if have Cold junction
44 A2FT
2.1 User Menu: The 2.2 Setup Menu: The setup 2.2.1 Basic Menu 2.3 Manual Mode RPT1 SKTB profile function transfer mode ON: Alarm output ON ifsensor
81 CJLO calibration low Low: -5.00 High: 40.00 104 OFS2
Option function 2 output
SKT1 TSPC fails selection 1-5V: 1-5V retransmission
below user menu menu has been categorized (bASE): Use or key Menu: Press and hold TSP2 RPTC 17 PB
Proportional
Low: 0.0 High: 500.0°C (900.0°F)
coefficient
output
band value 45 A2SP Alarm 2 set point Low: -19999 High: 45536
parameters are into eight categories as below. to get bASE in the lower key for 5 seconds RPT2 SKTC
Integral time Alarm 2 deviation
Cold junction
0-10: 0-10 retransmission
SKT2 TSPD 46 A2DV Low: -19999 High: 45536 82 CJHI calibration high Low: -1999 High: 1999
available depends on 1. bASE: Basic Menu display, then use key until MANU indicator TSP3 RPTD
18 TI
value
Low: 0 High: 3600 sec value coefficient
output
AL2: Alarm 2 output
user’s selection. 2. oUT: Output Menu to enter basic menu flashes to enter manual RPT3 SKTD
19 TD
Derivative
Low: 0.0 High: 360.0 sec 47 A3OT Alarm 3 output
ALM: Alarm 3 output V1 calibration low
R22:
RALM: Reverse Alarm3 Output 83 V1L Low: -1999 High: 1999
3. ALRM: Alarm Menu parameters. mode [Link]. SKT3
TSP4
TSPE
RPTE
time value
NoNE: No alarm function
coefficient
NoNE: No selected
REVR: Reverse (heating) control V1 calibration high
4. EI: Event Input Menu or
RPT4 SKTE 20 OUT1
Output 1
action dtMR: Dwell timer action 84 V1G
coefficient
Low: -1999 High: 1999 4-20: 4-20mA retransmission
PV,SV function
5. SEL: User Select Menu SET bASE
SKT4
TSP5
TSPF
RPTF
dIRt : Direct (cooling) control action [Link]: Deviation high alarm
MA1 calibration low
output
85 MA1L Low: -1999 High: 1999 0-20: 0-20mA retransmission
6. CoMM: Communication RPT5 SKTF
RELY: Relay output [Link]: Deviation low alarm
coefficient
output
SSrd: Solid state relay drive output [Link]: Deviation band out of
SP1 Menu SKT5 TSPG
4-20: 4-20mA linear current band alarm 86 MA1G
MA1 calibration
Low: -1999 High: 1999 0-5V: 0-5V retransmission
TSP6 RPTG Output 1 high coefficient
SP2 7. Ct: Current Transformer OFS1
OFS2 RPT6 SKTG 21 O1TY
signal type
0-20: 0-20mA linear current [Link]: Deviation band in band
V2 calibration low
output
1-5V: 1-5V retransmission
SP3 Input Menu OFS3 SKT6 0-5V: 0-5VDClinear voltage
48 A3FN
Alarm 3 function for alarm 87 V2L
coefficient
Low: -1999 High: 1999
output
SP4 1-5V: 1-5VDC linear voltage alarm 3 output [Link]: Process value high alarm
SP5
8. PRoF: Profile Menu INPT
UNIT 0-10: 0-10VDC linear voltage [Link]: Process value low alarm 88 V2G
V2 calibration high
Low: -1999 High: 1999 0-10: 0-10 retransmission
DP
coefficient output
SP6 Select BPLS (Bumpless transfer), or [Link]: Heater break alarm
INLO Output 1 MA2 calibration low AL2: Alarm 2 output
SP7 2.2.2 Output Menu (oUT): INHI failure
0.0 ~ 100.0 % to continue output 1 [Link]: Heater short alarm 89 MA2L
coefficient
Low: -1999 High: 1999
EI2: Event2 Input
22 O1FT control function if the sensor fails, or E1.C.o: Event Input 1 Control
SFtR Use or key to get oUT in SP1L 2.5 Calibration Mode: Press and hold key transfer
select OFF (0) or ON (1) for ON-OFF MA2 calibration CT2: CT2 Input
CT 1R SP1H mode Alarm Output 90 MA2G Low: -1999 High: 1999
the lower display, then use FILT
for 2~3 seconds, release it to enter calibration control E2.C.o: Event Input 2 Control
high coefficient C82/C83/C42:
CT 2R 91 PL1L Power limit 1 low Low: 0 High:PL1H or 50%
DT MR key to enter output menu DISP 2.4 Auto-Tuning Mode: mode. Then press Key for 5 seconds to Output 1 ON-
Low:0.1°C(0.2°F) Alarm Output NoNE: Not selected
PB 23 O1HY OFF control 92 PL1H Power limit 1 high Low: PL1L High: 100 % 4-20: 4-20mA retransmission
PASS parameters. TI Press and hold key perform calibration. CALI hysteresis
High: 50.0°C(90.0°F) NoRM: Normal alarm action
93 PL2L Power limit 2 low Low: 0 High: PL2H or 50% output & Remote SP
LtCH: Latching alarm action
RUN or
TD
for 5 seconds until 2 sec minimum,3 sec maximum 24 CYC1
Output 1
Low: 0.1 High: 90.0 sec. 49 A3MD
Alarm 3 operation
HoLd: Hold alarm action
94 PL2H Power limit 2 high Low: PL2L High: 100 % 0-20: 0-20mA retransmission
CYCR RAMP mode
SET OUT
RR TUNE indicator flashes cycle time
[Link]: Latching & Hold action
NoNE: No Parameter output & Remote SP
ST EP Offset value selected 0-5V: 0-5VDC retransmission
T IMR
RET Y
to activate auto-tuning ADLO 25 OFST
for P control
Low: 0 High: 100.0 % [Link]: Set point holding alarm
dtMR: DTMR is moved to USER output & Remote SP
RELO ADHI Hysteresis control Low: 0.1°C
SEL1 OUT1 REHI mode. RTDL Ramp NoNE: No Ramp Function 50 A3HY
of alarm 3 High: 50.0°C(90.0°F)
Menu 1-5V: 1-5VDC retransmission
RMSP RTDH 26 RAMP function MINR: Use unit/minute as Ramp Rate dISP: DISP is moved to USER
SEL2 O1TY
CJLO OFF: Alarm output OFF if sensor
output & Remote SP
O1FT RINL selection HRR: Use unit/hour as Ramp Rate Menu
SEL3 CJHI 0-10: 0-10VDC retransmission
RINH Alarm 3 failure fails
O1HY V1L 27 RR Ramp rate Low: 0.0 High: 500.0°C(900.0°F) 51 A3FT Pb: PB is moved to USER Menu
SEL4 output & Remote SP
CYC1 CODE V1G transfer mode ON: Alarm output ON if sensor
SEL5 OFT L NoNE:Output2 turned off tI: TI is moved to USER Menu A.4.20: Alarm 4, 4-20mA
OFST MA1L fails
OFT H Output 2 COOL: Cooling PID Function td: TD is moved to USER Menu retransmission output & Remote
SEL6 OUT2 MA1G
28 OUT2 52 A3SP Alarm 3 set point Low: -19999 High: 45536
O2TY CALO V2L function AL1: Alarm 1 Function o1HY: O1HY is moved to USER SP
SEL7 V2G Alarm 3 deviation
O2FT CAHI rAL1:Reverse Alarm 1 Function 53 A3DV Low: -19999 High: 45536 Select 1st~8th Menu A.0.20: Alarm 4, 0-20mA
SEL8 CYC2 SFT MA2L value
MA2G RELY: Relay output 95~102 SEL1~8 parameter for user RR: RR is moved to USER retransmission output & Remote
CPB SFL1 ALM: Alarm 4 output
SSrd: Solid state relay drive output 54 A4OT Alarm 4 output menu Menu SP
DB SFL2 RALM: Reverse Alarm 4 Output
PL1L SFtH 4-20: 4-20mA linear current CPb: CPB is moved to USER A.0.5V: Alarm 4, 0-5V
Output 2
PL1H 29 O2TY 0-20: 0-20mA linear current Menu Option function 3 retransmission output & Remote
PL2L Note: Using Manual, Auto-Tuning, Calibration modes will break the control signal type
0-5V: 0-5VDClinear voltage db: DB is moved to USER Menu
105 OFS3
selection SP
PL2H loop and change some of the previous setting data. Make sure that the 1-5V: 1-5VDC linear voltage A1HY: A1HY is moved to USER A.1.5V: Alarm 4, 1-5V
system is allowable to apply these modes. 0-10: 0-10VDC linear voltage Menu retransmission output & Remote
A1SP: A1SP is moved to USER SP
Menu A.0.10: Alarm 4, 0-10V
 A.0.5V: Alarm 4, 0-5V
retransmission output & Remote
SP
can be configured as dwell timers by selecting dtMR for A1FN. If A1FN is set to 7. MANUAL CONTROL: To enable manual control, ensure the LOCK param-
Modbus A.1.5V: Alarm 4, 1-5V Offset value for low 4. WIRING DIAGRAM
Register
Parameter
Notation
Parameter
Description retransmission Range
output & Remote
134 OFTL
point calibration
Low: -1999 High: 1999
dtMR, Alarm 1 will act as a dwell timer. Similarly, Alarm 2, Alarm 3 and Alarm 4 eter is set to NONE. Press and hold for 6.2 seconds or until (Hand
Address
SP
135 OFTH
Offset value for high
Low: -1999 High: 1999 will act as dwell timers if A2FN, A3FN, or A4FN is set to dtMR. When the dwell Control) appears on the display. Press and hold for 5 seconds or until the
0 SP1 Set Point 1 Low: A.0.10:
SP1L Alarm
High: 4,SP1H
1 SP2 Set Point 2 Low:retransmission
SP1L High: SP1H
0-10V point calibration
timer is configured, the parameter DTMR is used for dwell time adjustment. The MANU indicator begins to flash. The lower display will show . The controller
output & Remote Input signal value
2 SP3 Set Point 3 Low:SPSP1L High: SP1H 136 CALO during low point Low: -19999 High: CAHI-1 dwell time is measured in minutes ranging from 0.0 to 4553.6 minutes. The Timer has now entered manual control mode. Indicates the output control variable
3 SP4 Set Point 4 Low:C72:
SP1L High: SP1H calibration starts to count as soon as the Process Value (PV) reaches its set point (SV), and for output 1, and indicates the control variable for output 2. The user can use
4
105
SP5
OFS3
Set Point 5
Option function 3
Low:NoNE:
SP1L Not High: SP1H
selected Input signal value
triggers an alarm output once the time has elapsed. the up-down keys to adjust the percentage values for the heating or cooling
5 SP6 Set Point 6 Low:4-20:
SP1L4-20mA
High:retransmission
SP1H 137 CAHI during high point Low: CALO+1 High: 45536
6 SP7
selection
Set Point 7 Low:output
SP1L & High: SP1H 5.9 User Calibration: User calibration allows the user to offset the permanent output. This % value is based on the CYC1 and CYC2 settings, where the associ-
Remote SP calibration
Dwell timer 0-20: 0-20mA retransmission 138~139 … Reserved … factory calibration. There are two parameters: Offset Low (OFTL) and Offset ated output will stay on for the % of time the CYC1 & CYC2 values are set for. The
7 DTMR
output time output & Remote
Low: 0.0 High: 4553.5 SP 140 PROG Program code Same as PROG71 High (OFTH) for adjustment to correct an error in the process value. controller performs open loop control as long as it stays in manual control mode.
(Minute:
Seconds)
0-5V: 0-5VDC retransmission NoNE: none C22 Terminal Connection C62 Terminal Connection C82 /C42 Terminal Connection
There are two parameters for the sensor input. These two signal values are The manual mode menu can be reached by pressing keys also.
output & Remote SP SP2: SP2 activated to replace
J type1-5VDC
J_tC:1-5V: Thermocouple
retransmission SP1 CALO and CAHI. The input signal low and high values are to be entered in the Exit Manual Control: Press the key will revert the controller to its normal
K type& Thermocouple
K_tC:output Remote SP rS.A1: Reset alarm 1 output CALO and CAHI parameters respectively. display mode.
T_tC: T type Thermocouple
0-10V: 0-10VDC retransmission
E_tC: E type Thermocouple
rS.A2: Reset alarm 2 output
Press and hold the key until the setup Menu page is obtained. Then, press 8. DATA COMMUNICATION: The controllers support RS-485 Modbus RTU
output & Remote SP
B_tC: B type Thermocouple
rS.A3: Reset alarm 3 output
and release the key to navigate to the calibration low parameter OFTL. Send protocol for data communication.
AL4: Alarm 4 Output rS.A4: Reset alarm 4 output
R_tC: R type Thermocouple
C62: [Link]: Reset all alarm outputs your low signal to the sensor input of the controller, then press and release the RS-485 Setup: Enters the setup menu. Set individual addresses for units
S_tC: S type Thermocouple
NoNE: Not selected
N_tC: N type Thermocouple
Event input 1 [Link]: Cancel alarm latch key. If the process value (the upper display) is different from the input signal, connected to the same port. Set the Baud Rate (BAUD), Data Bit (DATA), Parity
141 E1FN
4-20: 4-20mA retransmission output
L_tC: L type Thermocouple
function d.o1: Disable output 1
the user can use and keys to change the OFTL value (the lower display) Bit (PARI) and Stop Bit (STOP) such that these values are accordant with PC
0-20: 0-20mA retransmission output d.o2: Disable output 2
8 INPT
Input sensor U_tC: U type Thermocouple
0-5V: 0-5VDC retransmission output d.o12: Disable output 1 and 2 until the process value is equal to the value the user needs. Press and hold the setup conditions.
selection P_tC: P type Thermocouple
1-5V: 1-5VDC retransmission output
C_tC: C type Thermocouple LoCK: Lock all parameters and key for 5 seconds to complete the low point calibration. A similar procedure 9. RETRANSMISSION: The controller can output (retransmit) PV or SP via its
0-10: 0-10VDC retransmission output
D_tC: D type
AL3: AlarmThermocouple
3 output
Read only communication C83 Terminal Connection C72 Terminal Connection R22 Terminal Connection is applied for high scale calibration. retransmission terminals RE+ and RE- provided that the retransmission option is
[Link]: PT100 Ω DIN curve [Link]: Switch Auto and Manual
As shown below, the two points OFTL and OFTH construct a straight line. For ordered. A correct signal type should be selected for option board to meet the
[Link]: Retransmit
[Link]: PT100 Ω JIS curve process control mode
Retransmission 4-20:value the purpose of accuracy, it is best to calibrate with the two points as far apart as retransmission option installed. RELO and REHI are adjusted to specify the low
106 RETY 4-20mA linear current input [Link]: Failure Transfer
5. PROGRAMMING
type 0-20mARetransmit
0-20:[Link]: set point
linear current input [Link]: EI Control Alarm Output possible. After the user calibration is complete, the input type will be stored in the scale and high scale values of retransmission.
0-5V:value
0-5VDC linear voltage input SP3: SP3 activated to replace 5.1 User Security: There are two 5.2 Control Output: There are 4 10. HEATER CURRENT MONITORING: A current transformer (CT98-1) is
Event input 2
kinds of control modes can be memory. If the input type is changed, a calibration error will occur and an error
Retransmission low1-5V: 1-5VDC linear voltage input 142 E2FN SP1 parameters PASS (password) and CODE required to measure the heater current. The CT input signal conditioner
107 RELO
scale value
Low: -19999 High: 45536
0-10: 0-10VDC linear voltage input
function
Others: Same as E1FN configured. code is displayed.
Retransmission oC: °C unit NoNE: none
(security code) to control the data security measures the heater current when the heater is powered (output 1 is on), and the
108 REHI Input unit Low: -19999 High: 45536 CODE Value PASS Value Access Rights Control Mode OUT 1 OUT 2 O1HY O2HY CPB DB
9 UNIT high scale value oF: °F unit
selection
SP4: SP4 activated to replace current value will remain unchanged the heater is unpowered (output 1 is off).
0 Any Value All parameters are changeable Heat Only REVR X ∆ X X X
Address Pu: Process unit SP1
=1000 All parameters are changeable
There are 1 or 2 CT inputs that can be connected to the controllers depending on
assignment of [Link]: No decimal point rS.A1: Reset alarm 1 output Cool Only DIRT X ∆ X X X
109 ADDR Low: 1 High: 255
Decimal point 1-dP: 1 decimal digit
digital rS.A2: Reset alarm 2 output
1000
≠1000 Only user menu parameters changeable the model. The CT1R & CT2R will indicate the heater current.
10 DP Heat PID
selection
communication 2-dP: 2 decimal digit rS.A3: Reset alarm 3 output =9999 All parameters are changeable REVR [Link] X O X X Heater break detection is enabled by enabling heater break detection setting
9999 Only SP1 to SP7 are changeable Cool ON- OFF
3 decimal
3-dP:2K4: digit baud rate
2.4 Kbits/s rS.A4: Reset alarm 4 output ≠9999
Heat PID
HBEN. A Heater break alarm ([Link]) alerts the user when the current measured
4K8: 4.8 Kbits/s baud rate [Link]: Reset all alarm outputs =CODE All parameters are changeable
Others
No parameters can be changed Cool PID
REVR COOL X X O O by CT1 in CT1R is lower than HB1T or CT2 in CT2R is lower than HB2T. When
9K6: 9.6 Kbits/s baud rate [Link]: Cancel alarm latch ≠CODE
14K4: 14.4 Kbits/s baud rate d.o1: Disable output 1 X: Not applicable
5.10 Digital Filter: In certain applications the process value is too unstable to the current measured by CT1 in CT1R is higher than HB1T+HBHY and CT2 in
Baud rate of digital
110 BAUD 19K2: 19.2 Kbits/s baud rate d.o2: Disable output 2 5.3 Signal Input: O: Adjust to meet process Requirements be read. To improve this, a programmable low pass filter incorporated in the CT2R is higher than HB2T+HBHY, the heater break alarm will be off. The Heater
communication
28K8: 28.8 Kbits/s baud rate
143 E3FN
Event input 3 d.o12: Disable output 1 and 2
INPT: Select the sensor type or signal type ∆: Required if ON-OFF Control is configured controller can be used. This is a first order filter with a time constant specified break alarm will be off when both CT values are in normal range. The Heater
38K4: 38.4 Kbits/s baud rate function LoCK: Lock all parameters and
57K6: 57.6 Kbits/s baud rate Read only communication for signal input. by the FILT parameter. A value of 0.5 seconds is used as a factory default. break alarm function will be enabled when OUT1 is in ON condition. Heater short
115K: 115.2 Kbits/s baud rate [Link]: Switch Auto and Manual Range: (Thermocouple) J_TC, K_TC, T_TC, E_TC, B_TC, R_TC, S_TC, Adjust FILT to change the time constant from 0 to 60 seconds. 0 seconds detection is enabled by enabling heater short detection setting HSEN. A Heater
Data bit count of
7bIt: 7 data bits
control mode
N_TC, L_TC, (RTD) [Link], [Link] or (Linear) 4-20, 0-20, 0-60, 0-1V, 0-5V, represents no filter applied to the input signal. short alarm ([Link]) alerts the user when the current measured by CT1 in CT1R is
111 DATA digital
8bIt:8 data bits
[Link]: Failure Transfer
1-5V, 0-10 5.11 Failure Transfer: The controller will enter failure mode if one of the follow- higher than HS1T or CT2 in CT2R is higher than HS2T. When the current
communication StAR: Run profile as RUN=STAR
EVEN: Even parity CoNt: Run Profile as UNIT: Select the process unit. Range: °C, °F, PU (Process unit). If the unit is ing conditions occurs. measured by CT1 in CT1R is lower than HS1T-HSHY and CT2 in CT2R is lower
112 PARI
Parity bit of digital
Odd: Odd parity RUN=CONT neither °C nor °F, then select PU. 1. SBER error occurs due to an input sensor break, input current below 1mA for than HS2T-HSHY, the heater short alarm will be off. The Heater short alarm will
communication
NoNE: No parity bit PV: Run Profile as RUN=PV
DP: Select the resolution of process value. 4-20mA or input voltage below 0.25V for 1-5V. be off when both CT values are in normal range. The Heater short alarm function
Stop bit count of HoLd: Run Profile as
1bIt: One stop bit
RUN=HOLD Range: For Thermocouple and RTD Signal [Link], 1-DP and for Linear Sign al 2. ADER error occurs due to the A-D converter of the controller fails. Output 1 will be enabled when OUT1 is in OFF condition.
113 STOP digital
communication
2bIt: Two stop bits
StoP: Run Profile as RUN=STOP [Link], 1- DP, 2-DP, 3-DP. and Output 2 will perform the failure transfer ([Link] & [Link]) function as the 11. EVENT INPUT: There are 6, 2 or 1 Event Inputs that are available in this
114 CT1R Reading of CT 1 Low: 0.0 High: 150.0
Event input 4
SP5: SP5 activated to replace
INLO: Select the low scale value for the linear type input. controller enters failure mode. series of controllers depending on the size of the controller. Refer wiring section
115 CT2R Reading of CT 2 Low: 0.0 High: 150.0 144 E4FN
function
SP1
INHI: Select the high scale value for the linear type input. 3. Alarm Failure Transfer: An alarm failure transfer is activated as the controller for wiring an event input. The Event input accepts a digital (on/off) type signal.
Enable Heater Others: Same as E3FN
116 HBEN
break detection
oFF: Off 1 oN: On
NoNE: none 5.4 Alarm: The controller has up to four alarm outputs depending on the control- enters failure mode. After that, the alarm output will transfer to the ON or OFF One of the available functions can be chosen by using EIFN1 through EIFN6
Heater break SP4: SP4 activated to replace
ler model. There are 11 types of alarm functions and one dwell timer that can be state which is determined by the set value of A1FT, A2FT, A3FT, and A4FT. contained in the setup menu. The same function cannot be set to more than one
117 HBHY Low: 0.1 High: 50.0
hysteresis SP1
selected. There are 4 kinds of alarm modes (A1MD, A2MD, A3MD, and A4MD) 5.12 Soft-Start: The controller has soft start function to limit the control output event input.
rS.A1: Reset alarm 1 output
118 HB1T
Triple point current
Low: 0.0 High: 120.0 rS.A2: Reset alarm 2 output available for each alarm function (A1FN, A2FN, A3FN, and A4FN). In addition to on out1 and out2 for a programmable time SFT or up to a programmed thresh- 12. REMOTE SET POINT: The set point will change proportionally with
for heater break 1
Triple point current rS.A3: Reset alarm 3 output the alarm output, output 2 can also be configured as an alarm. But output 2 has old value SFTH. The first of two will terminate soft start function and the normal respect to the input given in the Remote Set point input terminals. The Remote
119 HB2T
for heater break 2
Low: 0.0 High: 120.0 rS.A4: Reset alarm 4 output
only provides 8 different alarm functions or dwell timer available. PID control begins. This function is useful for effects such as suppressing the Set point function needs RMSP, RINL, RINH parameters to be set properly.
120 HSEN
Enable Heater short
oFF: Off 1 oN: On Event input 5
[Link]: Reset all alarm outputs
5.5 Alarm Modes: There are four types of alarm modes available for each alarm heater output during equipment startup, or lightening the load. 13. RAMP AND SOAK PROGRAM: The profiler option can be used in the
145 E5FN [Link]: Cancel alarm latch
detection function
d.o1: Disable output 1 function. Note: In Profile Version controllers If PFR is set to other than SP1 then the application where the set point should be changed automatically with the time. It
Heater short
121 HSHY
hysteresis
Low: 0.1 High: 50.0 d.o2: Disable output 2
Normal Alarm (ALMD = NORM): When a normal alarm is selected, the alarm profile function will continue with the set parameter during power recovery. If provides 1 program with 16 segment or 2 programs with each 8 segments or 4
Triple point current d.o12: Disable output 1 and 2
output is de-energized in the non-alarm condition and energized in an alarm PFR is set to SP1 then the profile will continue to run with soft start parameters programs with each 4 segments. Each segment has both ramp and soak
122 HS1T Low: 0.0 High: 120.0 LoCK: Lock all parameters and
for heater short 1
Read only communication condition. during power recovery. function. PROF, RUN, RMPU, STAR, END, PFR, HBLO, HBHI, HBT, CYC
Triple point current
123 HS2T
for heater short 2
Low: 0.0 High: 120.0 [Link]: Switch Auto and Manual Latching Alarm (ALMD = LTCH): If a latching alarm is selected, once the alarm There are 5 parameters available for soft start function. They are as below. parameters are used to configure the controller for ramp and soak programs. For
None: No Remote SP
control mode
output is energized, it will remain unchanged even if the alarm condition is 1. SFt: Soft start time. If SFt ≠0, then the Soft start function will be enabled. The more information of Profiler, please refer to full version user manual.
4-20: 4-20mA retransmission
[Link]: Failure Transfer
cleared. The latching alarm can be reset by pressing the RESET key once the SFt can be set in the form of Hour: Minute. The range can be set is 00.00 to 14. ERROR CODE:
SP7: SP7 activated to replace
output Event input 6
alarm condition is removed. 99:59. Error Display
Description & Reason
0-20: 0-20mA retransmission 146 E6FN
function
SP1
Code Symbol Corrective Action
output Others: Same as E5FN
Holding Alarm (ALMD = HOLD): A holding alarm prevents an alarm condition 2. SFL1: Soft Start output limit for output 1. It can be set from PL1L to PL1H.
Check and correct setup values of OUT2, PB1, PB2, TI1,
124 RMSP Remote SP type 0-5V: 0-5VDC retransmission 147 A1DL
Alarm 1 Delay OFF: OFF
during power up. This will ignore the alarm condition at first time after power on. 3. SFL2: Soft Start output limit for output 2. It can be set from PL2L to PL2H. Illegal setup values used: COOL is used
TI2 and OUT1. IF OUT2 is needed for cooling control,
(Minutes: Seconds) ON: Low: 00.01 High: 99.59 for OUT2 when DIRT (cooling action) is
output
Afterwards, the alarm performs the same function as normal alarm. 4. SFtH: Soft start threshold value. The Soft start will be aborted when the 4 ER04 used for OUT1, or when PID mode is not
the controller should use PID mode (PB≠ 0 and TI≠0)
1-5V: 1-5VDC retransmission Alarm 2 Delay OFF: OFF and OUT1 should use reverse mode (heating action),
148 A2DL
(Minutes: Seconds) ON: Low: 00.01 High: 99.59
Latching / Holding Alarm (ALMD = [Link]): A latching / holding alarm performs process value is greater than or equal to SFtH. used for OUT1 (PB =0 and/or TI=0)
otherwise, OUT2 cannot be used for cooling control.
output
Alarm 3 Delay OFF: OFF
both holding and latching functions. The latching alarm is reset when the RESET 5. SFtR: Soft start time. It will show the remaining time of soft start when it is
10 ER10 Communication error: bad function code Correct the communication software to meet
0-10: 0-10VDC retransmission 149 A3DL
output (Minutes: Seconds) ON: Low: 00.01 High: 99.59
key is pressed after the alarm condition is removed. running. the protocol requirements.
Alarm 4 Delay OFF: OFF Communication error: register address Do not issue an over range address of
125 RINL
Remote SP Input
Low: -19999 High:RINH-50 150 A4DL
(Minutes: Seconds) ON: Low: 00.01 High: 99.59 Set Point Holding Alarm (ALMD = [Link]): A set point holding alarm prevents 6. AUTO-TUNING: Auto-Tuning Operation Steps: 11 ER11 register to the slave.
low scale value out of range
Remote SP Input Soft Start Time
an alarm from power up and / or changing set point. The alarm output is de-ener- 1. The system has been installed normally. 14 ER14 Communication error: attempt to write a Do not write a read only data or a protected
151 SFT Low: 00.00(OFF) High:99.59
126 RINH
high scale value
Low: RINL+50 High:45536 (Hours: Minutes)
gized whenever the set point is changed even if it is in an alarm condition. The 2. Don’t use zero value for PB or TI, otherwise the auto-tuning program will be read only data data to the slave.
15 ER15 Communication error: write a value Do not write an over range data to the slave
Default File
dFLt: Default Menu 152 SPL1
Soft Start Power
Low: PL1L High:PL1H
alarm reverts to a normal alarm once the alarm condition is removed. disabled. The LOCK parameter should be set to NONE. which is out of range to a register register.
Limit for Output 1
127 FILE
Selection
[Link]: Load User Setting
Soft Start Power 5.6 Alarm Delay: In certain applications during startup, nuisance alarms will be 3. Set the set point to a normal operating value or a lower value if overshooting Event Input Error: Two or more event Do not set the same function in two or more Event
[Link]: Store User Setting 153 SPL2 Low: PL2L High:PL2H
beyond the normal process value will cause damage. 16 EIER inputs are set to the same function Input Function parameters (E1FN through E6FN).
Limit for Output 2
128 PV Process value Low: -19999 High: 45536 generated before the process value reaches the set point. To avoid these kinds
Current set point 154 SFTH Soft Start Threshold Low: -19999 High:45536
of nuisance alarms, a time delay for alarms is available. To enable the time delay 4. Press and hold the key until appears on the upper display, then let go.
129 SV Low: SP1L High: SP1H Soft Start Timer
value 155 SFTR Low: 00.00 High:99.59
for alarms, set the delay time using the A1DL, A2DL, A3DL, and A4DL parame- 5. Press and hold the key for at least 5 seconds. The TUNE indicator will
Output 1 (Hours: Minutes)
begin to flash, and the auto-tuning process has begun. 26 ATER Auto-Tuning Error: Failed to perform
130 MV1 percentage value Low: 0.00 High: 100.00 161~222
For Profiler parameters description, please refer to full version ters. These parameters will avoid the nuisance alarm during the process value auto-tuning function
(Heating) user manual
reaches set point. NOTE: If the ramping function is used, it will be disabled once auto-tuning is
Output 2
5.7 Ramp: The ramping function is performed during power up as well as any started. The auto-tuning mode is disabled if either a failure mode or manual
131 MV2 percentage value Low: 0.00 High: 100.00
time the set point is changed. Choose MINR or HRR for the RAMP setting, and control mode occurs.
(Cooling) 29 EEPR EEPROM can't be written correctly Return to factory for repair.
the controller will perform the ramping function. The ramp rate is programmed by Auto-Tuning Error: If auto-tuning fails, an ATER message will appear on Cold junction compensation for
132 PASS Password entry Low: 0 High: 9999
the upper display in any of the following cases. 30 CJER Thermocouple malfunction
Return to factory for repair.
Security code for Low: 0 High: 9999 adjusting the RR setting. The ramping function is disabled as soon as the Failure Input sensor break, or input current below
0 = unprotected
mode, the Manual control mode, the Auto-tuning mode or the Calibration mode ＊If PB exceeds 9000 (9000 PU, 900.0°F or 500.0°C)
133 CODE parameter
1000 = user mode unprotected 39 SBER 1mA if 4-20mA is used, or input voltage Replace input sensor.
protection 9999=SPx(1 to 7) unprotected occur. ＊If TI exceeds 1000 seconds below 0.25V if 1-5V is used
5.8 Dwell Timer: The Dwell timer can be with or without a Ramp. Alarm outputs ＊If the set point is changed during the auto-tuning process 40 AAER A to D converter or related component(s) Return to factory for repair.
malfunction