USER'S MANUAL FOR OXYGEN CONCENTRATOR

Contents

1 Foreword…………………………………..........……………2
2 Symbols…..........……………………………….……………2
3 Safety notice……...............…………………..……………3
4 Product introduction…....................................…..……4
5 Operation condition………….....……………………..……5
6 Scope of application…………..........………………………5
7 Technical parameter………........………..…………………5
8 Structures and Functions……………….....………….……6
9 Operation instructions…………................................…8
10 Alarms and safety devices.........………....………….…11
11 Maintenance…...........……………………..…………..…12
12 Troubleshooting……................................……………14
13 EMC Declaration..…....................................……..…16
14 Accessories……………………………………...…………19
15 Condition for transportation and storage....................20
16 Quality warranty......................................................20

JAGZ03-02 ver1.0 04/20/2015 JAGZ03-02 ver1.0 04/20/2015

1
 USER'S MANUAL FOR OXYGEN CONCENTRATOR USER'S MANUAL FOR OXYGEN CONCENTRATOR

1 Foreword 3 Safety notice

Thank you for purchasing our products, hoping you will be satisfied with our products.
This operation manual contains function, operation steps, basic trouble solution and so :This unit is not a life-support device , and in certain circumstances oxygen therapy
on. can be hazardous, it is suggested that if any patient who needs oxygen treatment,
To ensure your efficient use of the oxygen concentrator, please have a close read of this
please follow doctor’s advice to choose the right flow and period for oxygen before
operation manual before operating it.
using the oxygen concentrator.
2 Symbols :In the event of an alarm, you observe your oxygen concentrator not working properly,
The following table is a list of symbols and definitions that used with the Oxygen or if you feel discomfort, consult your Equipment Provider and /or your physician
Concentrator.
immediately.
Symbol Description Symbol Description :Use only voltage specified on rating label.
Indicating its conformity with the
Warning – Describes a hazard or :This device manufactures high concentration oxygen, which promotes rapid burning.
Medical Devices Directive
unsafe practice that can result in
93/42/EEC.The 0197 is the Keep oxygen concentrator far away from open flames and no smoking around the
severe bodily injury or death
number of the Notified Body. patient.
Caution – Describes a hazard or
:Do not leave a nasal oxygen cannula under bed coverings or chair cushions. If the
unsafe practice that can result in “ON” (power)
property damage unit is turned on without use, the oxygen will help the flammable material get fire .
:Use no lubricants, grease, or petroleum-based products on or near your oxygen
Follow User’s Manual “OFF” (power)
concentrator.
CLASS II equipment Serial number :Electrical shock hazard. Do not remove covers while the unit is plugged in. Only your
Equipment Provider or a qualified service technician should remove the covers or
Authorised Representative in the Separate collection for electrical
European Community and electronic equipment service the unit.
Type B Applied Part, :Care should be taken to prevent the unit from getting wet or allowing water to enter
The applied part complying with Variability, rotational adjustment.
the unit.
the specified requirements of To identify the control by means of
standard IEC/EN 60601-1 to which a quantity is controlled. The :The oxygen concentrator should be set to use in an environment without dust,
provide protection against controlled quantity corruption or toxicological harm gas.
electric shock, particularly increases/decreases by rotation
regarding allowable patient with the figure width. :Do not place the oxygen concentrator in surroundings where its airflow is obstructed.
leakage current :Do not place items on top of the concentrator.

Date of manufacture Alternating current :Always place the concentrator on a hard surface. Never place the concentrator on a
surface such as bed or couch, where the concentrator may tip or fall.
T6.3AL/
Manufacturer Type and rating of fuse :NEVER leave the concentrator unattended when plugged in.
250V
:Ensure the bottom smooth exhaustion during operating, otherwise the oxygen
Fragile, handle with care Keep dry
concentrator will be over-heated.

This way up Stacking limit by number :5 minutes are needed from oxygen concentrator from warming up to reach regular
function and normal performance.

2 JAGZ03-02 ver1.0 04/20/2015 JAGZ03-02 ver1.0 04/20/2015

3
 USER'S MANUAL FOR OXYGEN CONCENTRATOR USER'S MANUAL FOR OXYGEN CONCENTRATOR

NOTE: If oxygen does not seem to flow, first verify that the flowmeter ball is registering a 5 Operation conditions and Environment
flow. Then, place the tip of the cannula into a glass of water; if bubbles come out of the
Ambient temperature: 10℃-40℃
cannula, oxygen is flowing. If bubbles do not appear, turn off the oxygen concentrator
Relative humidity: 30%-85%
immediately and refer to Troubleshooting.
Air pressure: 700 hPa-1060 hPa
NOTE: There is never a danger of depleting the oxygen in a room when you use your Altitude: Up to 2286m without degradation; Consult your equipment provider for further
oxygen concentrator. information regarding to 2286m to 4000m
No corrosive gas and strong magnetic field around.
Radio Frequency Interference
Most electronic equipment is influenced by Radio Frequency Interference (RFI). When
6 Scope of application:
there is strong electromagnetic interference, maybe the LCD will be slightly affected, but
the oxygen concentrator is still running. ALWAYS exercise CAUTION with regard to the For Medical Use:
use of portable communications equipment in the area around such equipment. Medical oxygen supplied by the concentrator is beneficial to cure the disease or heart and
blood vessel system, chronic pulmonary system, the brain and blood vessel system,
chronic pulmonary tuberculosis, and other oxygen lacking symptoms, etc.
Requirement of environment protection For Health care:
Medical oxygen can be used for athletics and intellectuals and brainworkers, etc. to
The materials used in the system won’t create environment hazard. The packing materials
eliminate fatigue and also suit for the departments of health care, sanatorium, healthy,
of the system are recyclable, and they must be collected and disposed according to the
plateau military camps and hotels and other places where need oxygen.
related regulation in the country or region where the package of the system or its
accessories is opened. The nasal oxygen tube is made of medical PVC, and if it is thrown
7 Technical Parameters
away, it could not be bio-degradable, so it will cause the pollution. Any material of the
system, that may cause pollution in the environment, must be collected disposed strictly
Serial 3L 4L 5L 6L 8L 10L
complied with the local rules and requirements.
Rated power (VA) 300 300 400 300 400 550
Operation voltage
4 Product introduction AC230/50
(V/Hz)
Oxygen flow (L/mln) 0.5-3 0.5-4 0.5-5 0.5-6 0.5-8 0.5-10
The oxygen concentrator is a device that extracts oxygen from atmospheric air. It will
Oxygen
typically be an electrically-powered molecular sieve (artificial zeolite) used to separate 93%±3%
concentration (%)
nitrogen from ambient air. It could be applied widely in the hospitals at all different level, Outlet pressure
0.04—0.07
clinics, health centers and family nursing, health care for the old person, mental workers (Mpa)

and students, etc.. The oxygen concentrator can supply 1-2 patients simultaneously, with Power failure; low&high pressure ;
Alarm Optional：temperature; low purity; maintenance reminding after
steady oxygen flowing out, safe and reliable, low cost, adjustable flow. The key parts of
3000 hours use
the concentrator adopt anti-tiring and anti-aging design, and the planned life of the whole
Sound level (dB(A)) ≤43 ≤45 ≤50 ≤45 ≤50 ≤55
concentrator reaches up to 20,000 hours or 5 years, whichever comes first.
LCD display accumulating timing; present timing; timing;

4 JAGZ03-02 ver1.0 04/20/2015 JAGZ03-02 ver1.0 04/20/2015

5
 USER'S MANUAL FOR OXYGEN CONCENTRATOR USER'S MANUAL FOR OXYGEN CONCENTRATOR

Switch times; pressure digital(accuracy:0.001MPa); 8.1 Indicating Lamp

accumulating timing(range:0-99999hours); 8.1.1 Total 8 indicating lamps and their indication for the machine, which is shown as
present timing(accuracy:1 minute);
Large LCD display presetting timing(accuracy:1 minute) Figure 1, are as follows:
(optional) Optional : temperature digital(accuracy:0.1); a. P.O.: power switch (green lamp)
purity digital;
maintenance reminding; b. P.F.: power failure(red lamp)
SPO2 digital(accuracy:1%); c. H.P.: high pressure(red lamp)
Electrical category: Class II Type B d. L.P.: low pressure(yellow lamp)
Net Weight (Kg) 16 22 26 23 26 27 e. H.T.: over heated temperature(red lamp)
Atomization particle f. H.O2: oxygen purity is ≥85%, (blue lamp)(Accuracy:±3%)
≤5 μ reaches 90% only for atomization type
(optional) g. L.O2.: oxygen purity is < 85%,(red lamp)(Accuracy:±3%)
when oxygen purity is ≥85%, the blue lamp is on,
Low purity alarm 8.1.2 Total 6 indicating lamps and their indication for the machine, which is shown as
when oxygen purity is < 85%, red lamp is on, indicating low purity
(Optional)
Accuracy:±3% Figure 3, are as follows:
Pulse Pulse oximeter will be installed to oxygen concentrator to monitor a. P.O.: power switch (green lamp)
oximeter(optional) SPO2 on LCD display.
b. P.F.: power failure(red lamp)
T5AL/ T5AL/ T6.3AL/ T5AL/ T6.3AL/ T6.3AL/
Fuse c. L.P.: low pressure(yellow lamp)
250V 250V 250V 250V 250V 250V
d. H.P. /H.T: high pressure/ over heated temperature (red lamp)
8 Structures and Functions e. H.O2: oxygen purity is ≥85%, (blue lamp)(Accuracy:±3%)
f. L.O2.: oxygen purity is < 85%,(red lamp)(Accuracy:±3%)
8.2 Power switch
8.3 Oxygen flow meter
The location of float in the oxygen flow meter shows the outlet oxygen flow (L/min.).
8.4 Knob of oxygen flow meter switch
It adjusts and controls the outlet oxygen flow.
Do not Switch it over-forced, or else it is easy to damage the valve core. Switch it
counterclockwise to turn on, clockwise to turn off.
8.5 Outlet for Atomization (optional)
Figure 1 Figure 2
8.6 Intake air filter
Once need to replace, refer to 11.2 on page 13
8.7 Storage cabinet
It is used for storage oxygen cannula
8.8 LCD display( Liquid crystal display )
a.. It can display some status of during operation of the oxygen concentrator, refer to
7.on page 5
b. When starting the oxygen concentrator, the LCD screen is lighted, and it will return
to screen saver mode in 15 minutes. But if you press the right key during working, the
screen will be lighted again.
Figure 3 Figure 4

6 JAGZ03-02 ver1.0 04/20/2015 JAGZ03-02 ver1.0 04/20/2015

7
 USER'S MANUAL FOR OXYGEN CONCENTRATOR USER'S MANUAL FOR OXYGEN CONCENTRATOR

8.9 Timing buttons 9.2. Connect the nasal oxygen canula to the humidifier outlet nozzle or to the
The two buttons are used for timing adjustment, and each press of the left button(△) concentrator outlet if a humidifier has not been prescribed. Then set the nasal oxygen
will increase timing by 10min, the max timing is 40 hours. And each press of the right cannula over patient’s ears, insert the nasal oxygen cannula into patient’s nostrils to

button(▽) will decrease timing by 10min. When the right button(▽) is pressed to absorb oxygen; The nasal oxygen canula should be limited to 20 meters long, in order

reduce timing till “0”, the oxygen concentrator will turn off automatically. to ensure that the oxygen flow rate remains

8.10 Humidifier within specification values. The best absorbing

time for health care keeps 40-50 minutes per
Humidifier which is used for humidifying oxygen and preventing throat and nasal
time, absorbing time for medical treatment shall
mucosa stimulated by dry oxygen and dry hard sputum difficult to spit out.
be followed doctor’s advice, as shown in Figure
8.11 Knob of Atomizer switch (optional)
7.
8.12 Rating label
8.13 Appliance inlet Figure 7
9.3. Insert the power plug plug into the electrical
8.14 Holder
outlet of the correct voltage and frequency as
defined in 7(Technical Parameters)on page 5 ,
9 Operation instructions
and the power connector connected with the
appliance inlet of the oxygen concentrator, then Figure 8
:Be certain to place the unit where all sides are at least 30 cm away from walls,
set the I/O power switch to the “I” position to
draperies, furniture, or other obstructions. Do not place the unit in a confined area.
turn the unit on, at the same time the P.O. lamp
:Do not turn on or off frequently. To restart the oxygen concentrator after turning off,
will light(8.1.1a or 8.1.2a).
no less than 5 minutes are necessary (namely, exhaust internal gas of the oxygen
9.4. To set the flow of supplemental oxygen, turn
concentrator completely, for if air compressor turns on with pressure, its life will be the knob of oxygen flow meter switch left or
shortened) right until the ball inside the flowmeter centers
9.1. If used with a humidifier, unscrew the flask from the humidifier in clockwise direction, on the flow line number recommended oxygen
pour in proper distilled water or cold boiled water within the scale between the max absorbing flow.(counterclockwise—on,
line and the min line, then re-connect the top cover to the humidifier bottle, as shown clockwise—off).
Figure 9
in Figure 5 or Figure 6. The humidifier must comply with the general requirement of Flow value:
the 93/42/EEC European Directive as appropriate. 3L: 10position flow value from 0.5 ~ 5L/min on flowmeter, The maximum recommended
flow : 3L/min, and the scale line is red between 3L/min and 5L/min.
4L: 10position flow value from 0.5 ~ 5L/min on flowmeter as shown in figure 9. The
maximum recommended flow: 4L/min.
5L: 10position flow value from 0.5 ~ 5L/min on flowmeter as shown in figure 9. The
maximum recommended flow: 5L/min.
6L: 16position flow value from 0.5 ~ 8L/min on flowmeter. The maximum recommended
flow: 6L/min.
8L: 16position flow value from 0.5 ~ 8L/min on flowmeter. The maximum recommended
Figure 5 Figure 6
flow: 8L/min.

8 JAGZ03-02 ver1.0 04/20/2015 JAGZ03-02 ver1.0 04/20/2015

9
 USER'S MANUAL FOR OXYGEN CONCENTRATOR USER'S MANUAL FOR OXYGEN CONCENTRATOR

10L: 10position flow value from 0.5 ~ 10L/min on flowmeter. The maximum recommended atomization treatment.
flow: 10L/min. d. Do clean the atomization devices followed by the instructions of the atomization
In compliance with the ISO8359 standard, the flow supplied is equal to the flow set on the devices.
flowmeter, accurate to within 10% or 200ml/min, whichever is the larger of the two USE OF PULSE OXIMETER (for optional)
The variation of the maximum recommended flow does not exceed 10% of the indicated 1. Insert the pulse oximeter probe joint to the pulse oximeter connector on the oxygen
value when a back pressure of 7kPa is applied to the output of the device. The maximum concentrator.(see Figure 11), and the LCD will show the Figure 12.
outlet pressure is 70kPa 2. Put the finger completely into the pulse oximeter
Unplug the power plug
Oxygen Concentration: 3. The SPO2(measuring range: 35%~100%; accuracy: 70% to 100% ±2 digits) and Pulse
-at 2L/min: >90% Rate(measuring range: 30bpm~240bpm; accuracy:±2bpm or±2%) reading will display
-at 3L/min: 93%(±3%) on the screen in few seconds.(see Figure 13)
-at 4L/min: 93%(±3%)
-at 5L/min: 93%(±3%)
-at 6L/min: 93%(±3%)
-at 8L/min: 93%(±3%)
-at 10L/min: 93%(±3%) Figure 10
:It is very important to select only the prescribed level of oxygen. Change the flow
selection only under the guidance of your physician.
Pulse oximeter probe
9.5 . When finished the absorbing, set the I/O power switch to the “O” position to turn off
the unit, if there is discontinuous use, please unplug the power plug, as shown in
Figure 11
Figure 10
9.6. If the patient needs timing oxygen absorbing, please refer to 8.9 on page 8

Atomization operation methods (for optional)

The atomization function of the concentrator is applicable to help to cure the sufferers of
chronic pulmonary tuberculosis and respiratory system, etc.
:Atomization treatment must be under advice and suggestion of your physician.
Figure 12 Figure 13
:Using distilled water to do the atomization for several seconds after each operation
may lighten the crystallization caused by medical solution. 10 Alarms-Safety devices
:If atomizing cannot work then open the cover of the bottle and add clean water in
small amount. Rotate the white ball which lies in the bottle with the gas resource 10.1 Alarms

connected and select the proper angle to gain a better atomization. a. Power failure alarm: In case of a loss of mains power or when the power cord is not

a. Open the cover of medical cup, and add atomization remedy that needed, then close plugged into the wall outlet, an audible alarm is activated with red indicator on(8.1.1b

the cover. or 8.1.2b on page 7). The troubleshooting is referred to 12 on page 14.

b. Connect the joint of atomization nozzle (or mask) with the cover of medical cup, and b. low&high pressure alarm: There is a pressure sensor on the main board to check

then connect the other end of atomizer connection tube with the atomization outlet and the system pressure, when the pressure is lower than 0.1Mpa,there is an audible

turn on atomizer. alarm with yellow indicator on(8.1.1d or 8.1.2c on page 7) and the oxygen

c. Turn on the power of oxygen concentrator, and shut up flow meter, then it is ready for concentrator is still working; When the pressure is higher than 0.23Mpa,there is an

10 JAGZ03-02 ver1.0 04/20/2015 JAGZ03-02 ver1.0 04/20/2015

11
 USER'S MANUAL FOR OXYGEN CONCENTRATOR USER'S MANUAL FOR OXYGEN CONCENTRATOR

audible alarm with red indicator on(8.1.1c or 8.1.2d on page 7) and the oxygen 11.2. Clean air filter: It is a critical step for daily maintenance to clean intake air filter, at
concentrator is stopped. The troubleshooting is referred to 12 on page 14. least twice a month.
c. Low oxygen concentration alarm(OCSI): The oxygen concentration will rise to the Detail steps: remove the two intake air filters on both sides of the body, clean them
normal level in five minutes of operation. When oxygen purity is≥85%, the green with mild household cleaner and clean it with clean water completely, get ride of
lamp(8.1.1f or 8.1.2e on page 7) is on, when oxygen purity is <85%, red lamp is on extra water and dry up naturally, finally set back after dry up, as shown in Figure 15.
for audible alarm, indicating low purity(8.1.1g or 8.1.2f on page 7). Refer to the
troubleshooting on page 14. Or call your supplier to service the device
d. Temperature alarm: There is a temperature sensor on the main board to check the
internal temperature, when the temperature is higher than 50°C in the oxygen
concentrator, there is an audible alarm with red indicator on(see H.T. on the lamp)
and the oxygen concentrator will be stopped. The troubleshooting is referred to 12 on
page 14. Air filter
10.2 Safety devices
a. Compressor motor:
Thermal safety is ensured by a thermal switch situated in the motor winding(145±5℃).
b. Safety valve:
This is fitted on the compressor outlet and is calibrated to 2.5 bar(250kPa).

11 Maintenance Figure 15
11.3. Clean secondary filter
:Disconnect the power cord from the electrical outlet before you clean the cabinet. Method I: Clean secondary filter an interval about 800 hours, open the top cover and
:Do not operate the concentrator without the filters installed, or while filters are wet. take out storage case,Rotate the air filter with counterclockwise direction as Figure
These actions could permanently damage the concentrator. 16,take down the filter cloth, then clean it with detergent, and then clean it out with
NOTE: If legally binding regulations govern the installation, service and/or the operation of clean water completely, get rid of the extra water, and dry it naturally, finally set back
the product, it is the responsibility for the operator to observe and follow these regulations. after dry up.
NOTE: Modifying the product is not permitted.
11.1. Clean the whole body: In the condition of power off, make a clean for the outside
body by soft towel with little mild household cleaner , and then wipe it up with dry
towel, once or twice per month.

Figure 16

Method II: First, remove the silicone tube connected with oxygen output, take down
the humidification bottle, Rotate the air filter with counterclockwise direction as
Figure 17,take down the filter cloth, clean with detergent, wash by clean water, wipe
Figure 14 off the water. and make it to be dry in air naturally ,then install back to the Air filter.

12 JAGZ03-02 ver1.0 04/20/2015 JAGZ03-02 ver1.0 04/20/2015

13
 USER'S MANUAL FOR OXYGEN CONCENTRATOR USER'S MANUAL FOR OXYGEN CONCENTRATOR

No. Trouble Causes Solution

1. No connection
between circuit of
No operation after oxygen concentrator 1. Check out whether switch, plug,
power connected and and power power line in good connection.
1
the P.F. lamp is light 2. Circuit of fuse 2. Replace the fuse protector and
with audible alarm. protector broken. find the cause
3. There is no power
supply.
Figure 17 1. Connect the oxygen tube again
1. Folded inside
2. Clean the filter
11.4. Clean the humidifier (if the humidifier is prescribed by a physician) oxygen tube, no
3. Take off the cover, screw well
smooth outtake
Daily: the cover, block the outtake by
No oxygen out or tiny 2. Filter clogged, no
2 thumb after turning on, and
- Empty the water from the humidifier. outtake flow smooth intake
there will some sound from the
- Rinse the humidifier flask under running water. 3. The cover of
humidifier after 5 second around
dampen bottle
- Fill humidifier up to the mask with distilled water. (the safety valve of humidifier
leaking
turns on)
Regularly:
1. Air controller cannot
- Disinfect the humidifier parts by immersing them in a disinfectant solution(in 1. Have air control valve replaced
work
3 No exhaust sound 2. Have electric control board
general, we recommend using water containing a small amount of chlorine bleach). 2. Electrical control
replaced
board cannot work
- Rinse and dry.
1. The joint of
- Check that the humidifier lid seal is in good condition. exhaustion muffler
1. Connect the joint well
4 Too noisy exhaustion fallen off
2. Have the muffler replaced
2. Exhaustion muffler
11.5. Clean Oxygen tubing and nasal cannula
broken
Follow the manufacturer’s instructions The oxygen
Check every gas circuit connectors
11.6. Replacement of fuse tube concentrator is working The system pressure
5 with soapy water whether there are
but the L.P. lamp is light is too low.
Remove the cover of fuse, which is in the air leakage.
with audible alarm.
appliance inlet, dismantle the fuse tube off by
1.Check the fan’s connector on the
small screwdriver. Close the cover of fuse after The oxygen main board whether it is bad
The temperature in the
fuse tube is replaced. concentrator is stopped contact.
6 oxygen concentrator is
Figure 18 and the H.T. lamp is 2.turn off the oxygen concentrator
The other fuse tube is located at the intake of too high.
light with audible alarm. and consult your Equipment
internal power line; the method of replacement Provider.
is the same with that above. The oxygen
Turn off the oxygen concentrator
concentrator is stopped The system pressure
7 and consult your Equipment
12 Troubleshooting and the H.P. lamp is is too high.
Provider.
light with audible alarm.
If your concentrator fails to operate properly, please refer to the troubleshooting chart on 1. Check every gas circuit
the following pages for probable causes and solutions. If problems with the equipment The oxygen connectors with soapy water
concentrator is working Oxygen concentration whether there are air leakage.
continue, please contact your Equipment Provider. 8
but the L.O2 lamp is is too low. 2. Turn off the oxygen concentrator
NOTE: If the unit has not been used for an extended time period, it needs to operate for light. and consult your Equipment
several minutes before power failure alarm can become activated. Provider.

14 JAGZ03-02 ver1.0 04/20/2015 JAGZ03-02 ver1.0 04/20/2015

15
 USER'S MANUAL FOR OXYGEN CONCENTRATOR USER'S MANUAL FOR OXYGEN CONCENTRATOR

13 Information on Electromagnetic compatibility

Guidance and manufacturer’s declaration – electromagnetic immunity
The 5L machine is intended for use in the electromagnetic environment specified below.
The 5L machine needs special precautions regarding EMC and needs to be installed and The customer or the user of the 5L machine should assure that it is used in such an
put into service according to the EMC information provided in the accompanying
IMMUNITY IEC 60601 Electromagnetic
documents; Compliance level
test test level environment –guidance
Portable and mobile RF communications equipment can affect the 5L machine.
Floors should be wood,
All cables and maximum length of cables, Transducers and other accessories with which Electrostatic concrete or ceramic tile. If
the manufacturer of the 5L machine claims compliance with the requirements, Accessories discharge ± 6 kV contact ± 6 kV contact floors are covered with
that do not affect compliance with the requirements of these sub clauses need not be listed.
(ESD) ± 8 kV air ± 8 kV air synthetic material, the
IEC 61000-4-2 relative humidity should be
Accessories, transducers and cables may be specified either generically or specifically. at least 30 %.
NOTE：
± 2 kV for power
± 2 kV for power Mains power quality should
Transducers and cables sold by the manufacturer of the 5L machine as replacement parts Electrical fast supply lines
supply lines be that of a typical
for internal components need not be listed. transient/burst ± 1 kV for
± 1 kV for input/output commercial or hospital
IEC 61000-4-4 input/output
The use of accessories, transducers and cables other than those specified, with the lines environment.
Lines
exception of transducers and cables sold by the manufacturer of The 5L machine as
± 1 kV line(s) to Mains power quality should
replacement parts for internal components, may result in increased emissions or decreased ± 1 kV line(s) to
Surge line(s) be that of a typical
line(s)
immunity of The 5L machine. IEC 61000-4-5 ± 2 kV line(s) to commercial or hospital
± 2 kV line(s) to earth
earth environment.
Guidance and manufacturer’s declaration – electromagnetic emissions
<5 % UT <5 % UT
Voltage dips, Mains power quality should
The 5L machine is intended for use in the electromagnetic environment specified below. The (>95 % dip in UT) (>95 % dip in UT)
short be that of a typical
customer or the user of the 5L machine should assure that it is used in such an environment. for 0,5 cycle for 0,5 cycle
interruptions commercial or hospital
40 % UT 40 % UT
Emissions test Compliance Electromagnetic environment – guidance and environment. If the user of
(60 % dip in UT) (60 % dip in UT)
voltage the 5L machine requires
for 5 cycles for 5 cycles
The 5L machine uses RF energy only for its internal variations continued operation during
70 % UT 70 % UT
RF emissions function. Therefore, its RF emissions are very low on power power mains interruptions, it
Group 1 (30 % dip in UT) (30 % dip in UT)
supply is recommended that the 5L
CISPR 11 and are not likely to cause any interference in nearby for 25 cycles for 25 cycles
input lines machine be powered from
electronic equipment. <5 % UT <5 % UT
IEC 61000-4- an uninterruptible power
(>95 % dip in UT) (>95 % dip in UT)
The 5L machine is suitable for use in all 11 supply or a battery.
for 5 s for 5 s
RF emissions establishments other than domestic, and may be used
Class A Not applicable
CISPR 11 in domestic establishments and those directly
Note: The 5L machine
connected to the public low-voltage power supply does not contain
network that supplies buildings used for domestic components Power frequency magnetic
Harmonic Power
purposes, provided the following warning is heeded: susceptible to fields should be at levels
emissions Class A frequency
Warning: This 5L machine is intended for use by magnetic fields, such characteristic of a typical
IEC 61000-3-2 (50/60 Hz) 3 A/m
healthcare professionals only. This equipment/ system as Hall elements or location in a typical
magnetic field
magnetic field sensors. commercial or hospital
Voltage may cause radio interference or may disrupt the IEC 61000-4-8
Therefore, the EUT is environment.
fluctuations/ operation of nearby equipment. It may be necessary deemed to meet the
Complies to take mitigation measures, such as re-orienting or
flicker emissions requirement without
IEC 61000-3-3 relocating the 5L machine or shielding the location. actual testing.

16 JAGZ03-02 ver1.0 04/20/2015 JAGZ03-02 ver1.0 04/20/2015

17
 USER'S MANUAL FOR OXYGEN CONCENTRATOR USER'S MANUAL FOR OXYGEN CONCENTRATOR

Guidance and manufacturer’s declaration – electromagnetic immunity Recommended separation distances between portable and mobile RF
The 5L machine is intended for use in the electromagnetic environment specified below. communications equipment and the 5L machine
The customer or the user of the 5L machine should assure that it is used in such an The 5L machine is intended for use in an electromagnetic environment in which radiated
electromagnetic environment. RF disturbances are controlled. The customer or the user of the 5L machine can help
IMMUNITY IEC 60601 Compliance Electromagnetic environment – prevent electromagnetic interference by maintaining a minimum distance between
test test level level guidance portable and mobile RF communications equipment (transmitters) and the 5L machine as
Portable and mobile RF recommended below, according to the maximum output power of the communications
communications equipment should be equipment.
used no closer to any part of the 5L Separation distance according to frequency of transmitter
Rated maximum
machine, including cables, than the m
output power
recommended separation distance 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2,5 GHz
calculated from the equation applicable of transmitter
to the frequency of the transmitter. W
Recommended separation distance
0.01 0.12 0.12 0.07

80 MHz to 800 MHZ 0.1 0.37 0.37 0.22

800 MHz to 2,5 GHz 1 1.17 1.17 0.70
3 Vrms 3 Vrms where P is the maximum output power
10 3.69 3.69 2.21
Conducted RF 150 kHz to 80 150 kHz to 80 rating of the transmitter in watts (W)
IEC 61000-4-6 MHZ MHZ according to the transmitter 100 11.67 11.67 7.00
Radiated RF 3 V/m 3 V/m manufacturer and d is the
For transmitters rated at a maximum output power not listed above, the recommended
IEC 61000-4-3 80 MHz to 80 MHz to 2,5 recommended separation distance in
separation distance d in metres (m) can be estimated using the equation applicable to
2,5 GHz GHz metres (m).
Field strengths from fixed RF the frequency of the transmitter, where P is the maximum output power rating of the
transmitters, as determined by an transmitter in watts (W) according to the transmitter manufacturer.
electromagnetic site survey,a should NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency
be less than the compliance level in range applies.
each frequency range.b NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is
Interference may occur in the vicinity of affected by absorption and
equipment marked with the following reflection from structures, objects and people.
symbol:
14 Accessories
Your concentrator includes the following components:
• Intake air filter (two pieces, part number:GL-01)
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is • Secondary filter (one piece, part number:GL-02)
affected by absorption and reflection from structures, objects and people. The concentrator comes with two air filters and one secondary filter already installed.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) : Please use the parts mentioned in this chapter, if the use of other parts can degrade
telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV minimum safety and performance.
broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
: Please choose the suitable humidifier and Nasal oxygen cannula, they must:
environment due to fixed RF transmitters, an electromagnetic site survey should be
considered. If the measured field strength in the location in which the 5L machine is used - be oxygen compatible,
exceeds the applicable RF compliance level above, the 5L machine should be observed - be biocompatible,
to verify normal operation. If abnormal performance is observed, additional measures
may be necessary, such as re-orienting or relocating the 5L machine.
- include a means to prevent the propagation of fire and accord with requirements of ISO
b
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m. 8359:1996/Amd.1:2012

18 JAGZ03-02 ver1.0 04/20/2015 JAGZ03-02 ver1.0 04/20/2015

19
 USER'S MANUAL FOR OXYGEN CONCENTRATOR

15 Condition for transportation and storage

Environment temperature scale: -40~55℃
Comparative humidity scale: ≤95%
Air pressure scale: 700 –1060 hpa
Fuse
Indicator Timing
~230V

16 Quality Warranty
Warranty for whole unit:15 months
LCD
Warranty for magnetic valve:24 months
Warranty for compressor:24 months

Control valve
M M

Fan Compressor

PCB

Oxy. sensor

DISTRIBUTOR:
ADDRESS:
TELEPHONE:
P.F.
FAX:

Transformer

Sensor

20 JAGZ03-02 ver1.0 04/20/2015 JAGZ03-02 ver1.0 04/20/2015