Scribd
Upload
10 views

PREP CH2 - Motion Lesson Slides

This document discusses key concepts related to motion including: 1. Scalar and vector quantities - Scalar quantities only have magnitude while vectors have both magnitude and direction. 2. Position, distance, and displacement - Position is a vector, distance is a scalar length of path, and displacement is the difference between initial and final position vectors. 3. Speed and velocity - Speed is a scalar and velocity is a vector that includes both magnitude and direction of motion. Velocity is calculated as displacement over time.

Uploaded by

nisaselincam
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
10 views

PREP CH2 - Motion Lesson Slides

This document discusses key concepts related to motion including: 1. Scalar and vector quantities - Scalar quantities only have magnitude while vectors have both magnitude and direction. 2. Position, distance, and displacement - Position is a vector, distance is a scalar length of path, and displacement is the difference between initial and final position vectors. 3. Speed and velocity - Speed is a scalar and velocity is a vector that includes both magnitude and direction of motion. Velocity is calculated as displacement over time.

Uploaded by

nisaselincam
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 13

CH.

2
DESCRIBING MOTION
Ceren Çetinkaya
DESCRİBİNG MOTİON
Scalar quantities
Remember scalar quantities only have a magnitude(size)

such as mass, volume, and time that can be completely specified by their magnitude
and have no direction.

Vector quantities
Remember vector quantities have both magnitude and direction
DESCRİBİNG MOTİON
While you are sitting on the chair, are you moving according to the
Earth and the Sun?

When we discuss the motion of something, we describe the motion


relative to something else.

Position
A position is a vector which represents the position of an object in
space in relation to an arbitrary reference point.
DISTANCE AND DISPLACEMENT
▪ Distance is the length of path taken by the object during a motion.
Initial and final positions of the object are not sufficient to determine
distance.

▪ Displacement is a vector quantity which refers the difference between


the final position vector and initial position vector. The magnitude of
the displacement gives the minimum distance between two points.
SPEED & VELOCITY
Speed
• The speed of an object is the distance it travels per unit time
• Speed is a scalar quantity
• This is because it only contains a magnitude (without a direction)

Where:
• Speed is measured in metres per second (m/s)
• Distance travelled is measured in metres (m)
• Time taken is measured in seconds (s)

Average Speed
is the ratio of total distance covered and corresponding time interval

Instantaneous speed is the speed at any instant of time and can be defined as the
average speed over an infinitesimally short time interval.

If you’re cited for speeding, which does the police officer write
on your ticket: your instantaneous speed or your average
speed?
HOW TO USE FORMULA TRIANGLES
QUESTION P.21
DESCRİBİNG MOTİON
Velocity
• The velocity of a moving object is similar to its speed, except it also describes the object’s direction
• The velocity of an object contains both magnitude and direction, e.g. ‘15 m/s south’ or ‘250 mph
on a bearing of 030°’
• Velocity is therefore a vector quantity because it describes both magnitude and direction

Where:
• v = velocity in metres per second (m/s)
• s = displacement, measured in metres (m)
• t = time, measured in seconds (s)
Velocity is a vector quantity, so it uses displacement, s, rather than distance which is scalar.
QUESTION P.23
ACCELERATION
•Acceleration is defined as the rate of change of velocity
• In other words, it describes how much an object’s
velocity changes every second

•Where:
• a = acceleration in metres per second squared (m/s2)
• Δv = change in velocity in metres per second (m/s)
• Δt = time taken in seconds (s)

•The change in velocity is found by the difference between the


initial and final velocity, as written below:
change in velocity = final velocity − initial velocity
Δv = v − u
•Where:
• v = final velocity in metres per second (m/s)
• u = initial velocity in metres per second (m/s)
SPEEDING UP & SLOWING DOWN
•An object that speeds up is accelerating
•An object that slows down is decelerating

•The acceleration of an object can be positive or negative,


depending on whether the object is speeding up or slowing
down
• If an object is speeding up, its acceleration is positive
• If an object is slowing down, its acceleration
is negative (sometimes called deceleration)
1. DISTANCE-TIME GRAPHS
•A distance-time graph shows how the distance of an object moving in
a straight line (from a starting position) varies over time:

Constant Speed on a Distance-Time Graph

•Distance-time graphs also show the following


information:
• If the object is moving at a constant speed
• How large or small the speed is
CONTINUED..

•A straight line represents constant speed


•The slope of the straight line represents
the magnitude of the speed:

• A very steep slope means the object is moving at


a large speed

• A shallow slope means the object is moving at


a small speed

• A flat, horizontal line means the object


is stationary (not moving)

You might also like