Scribd
Upload
285 views2 pages

Boundry Wall Design (A)

This document provides design details for the boundary wall and strip foundation of a structure. It includes calculations for base pressure, overturning, sliding, bending moment, shear stress, and steel reinforcement of the foundation. The calculations show that the base pressure, overturning, and sliding checks meet the required factors of safety. The provided depth, steel reinforcement area and spacing are sufficient to resist the maximum bending moment and shear stresses on the foundation.

Uploaded by

Hikmat B. Ayer - हिक्मत ब. ऐर
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
285 views2 pages

Boundry Wall Design (A)

This document provides design details for the boundary wall and strip foundation of a structure. It includes calculations for base pressure, overturning, sliding, bending moment, shear stress, and steel reinforcement of the foundation. The calculations show that the base pressure, overturning, and sliding checks meet the required factors of safety. The provided depth, steel reinforcement area and spacing are sufficient to resist the maximum bending moment and shear stresses on the foundation.

Uploaded by

Hikmat B. Ayer - हिक्मत ब. ऐर
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Design of Boundary wall with Strip foundation‐ wall location

Sno Description = Value Units


1 Net SBC of soil at fdn depth = 30.5 Kn/sqm
1 Height of the boudnary wall = 2.5 m
2 Grade of concrete = 20 N/Sqmm
3 Grade of steel = 500 N/Sqmm
4 Grade of cement mortar for brickwork =
5 Wind speed = 47 m/s
6 Value of K1 = 0.71
7 Value of K2 = 0.8 Terrain cat 4
8 Value of K3 = 1
9 Value of K4 = 1
10 Vz = Vb x k1 x k2 xk3 xk4 = 26.696
11 Pz= 0.6 x Vz x vz = 428 N/m2
12 Pz in KN/sqm = 0.428 KN/m2
13 Density of soil = 18 kn/cum
13 Density of brickwork = 20 kn/cum
14 Density of RCC = 25 kn/cum
15 width of brickwork = 0.23 m 0.23
16 Depth of the foundation = 1.5 m
17 Width of foundation = 1.3 m
18 Thickness of foundation = 0.3 m
19 Width of plinth beam = 0.3 m
20 Thickness of beam = 0.3 m 2.5
Loads and moments calculation
A) BASE PRESSURE CHECK
Moment due to wind load is considered pillar design due to H/L ratio
=1, where H=2.5m and Length between the piers =2.5m
weight of Brickwork/m = 15.64 KN/m NGL
Weight of plinth beam/m = 2.25 KN/m
weight of soil above footing/m = 23.112 KN/m 0.3
1.2
weight of foundation/m = 7.5 KN/m
0.3
Total dead weight of BW/m = 48.502 KN/m
Moment due to wind load is not considered
due to H/L ratio =1 = 0 KN‐m/m 0.3
P/A = 37.31 KN/sqm
M/z = 0 KN/sqm 0.5 0.3 0.5
P/A+M/Z ( Max pressure) = 37.3092308 KN/sqm 1.3

P/A‐M/Z ( Min pressure) shall not be < 0 = 37.3092308 KN/sqm


Gross SBC = 57.5 KN/sqm
Check for base pressure is OK
B) Overturning check
Total overturniing moment due to wind @
Base = 0

The total resiting moment (P X fdn width/2) = 31.5263


Factor of safety RM/OTM = NA
Check for Over turning is OK
C) Check for Sliding

Total horizontal wind force at the base of fdn = 1.07 Kn/m


Total resisiting force from the wt of fdn = 14.5506 Kn/m
Factor of safety = 13.60
Check for Sliding is OK

Page 1 of 2
Design of Boundary wall with Strip foundation‐ wall location
Sno Description = Value Units
D) Design of foundation
Max pressure of the foundation = 37.31 Kn/m
Factored pressure from the foundation = 55.96 Kn/m

Max bending moment at the face of beam = 27.98 Kn‐m/m


Depth required as per BM = 88 mm
Depth provided in mm is = 300 ok
Effective depth = 250 mm
2
MU / ( b X d2 ) = 0.45 N / MM
Shear at above point = 28 KN/m
2
PU / ( b X d ) = 0.11 N / MM
2
Allowable shear stress = 0.28 N / MM
Shear stress of the footing is OK
% of Steel as per Table ‐ 3 of SP : 16 = 0.104
% of Steel as per Table ‐ 19 of IS: 456 = 0.120
Required Area of Steel for Maximum of
3.00 Sq.CM
above =
Min. Requirement as 0.12% of Gross Area 3.60 Sq.CM
=
Max. of above = 3.60 Sq.CM
Reinforcement Dia Proposed = 10 MM
Spacing Proposed as per above & to Table‐
100 MM
96 =
Provided Area of Steel as per Table‐96 = 7.86 Sq.CM
Provide 10 Dia @ 100 C/C in both ways

Page 2 of 2

You might also like