ME-204: FLUID MECHANICS

S. No. Contents Contact

Hours

1 Introduction: Fluid and flow definition and types, continuum, fluid 4

properties.
Fluid Statics: Pressure variation in a static fluid; hydrostatic
manometry; forces on planes and curved surfaces, stability of
submerged and floating bodies.
2 Fluid kinematics: General description of fluid motion, steady flow,
uniform flow; stream, streak and path lines; Lagrangian and Eulerian
approach; Continuity equation, particle acceleration; rotational and
irrotational flow; stream function;velocity potential function, flow nets;
circulation; simple flows; source, sink, vortex, doublet, free and forced
vortex.

3 Fluid Dynamics: Concept of system and control volume; Reynold's 7

transport theorem, Euler's equation, Bernoullis equation, Navier
Stokes equation; Flow measurement- Venturimeter, Orfice meter,
Pitot- tube, flow meters,notches.
Dimensional analysis: Buckingham's - Theorem. Non-dimensional
parameters, similarity and its application to fluid problems.
4 Viscous flow: Laminar flow between parallel surfaces and through 7
the circular pipes, Momentum and Kinetic energy correction factors;
power absorbed in viscous resistance, film lubrication.

ME-54

5 Turbulent flow: Transition from laminar to turbulent flow, turbulence 8

and turbulence intensity, turbulence modeling, Prandtl mixing length
hypothesis; flow losses in pipes- major and minor losses, pipes in
series and parallel, hydraulically smooth and smooth and rough pipes,
friction factor charts.
6 Laminar and Turbulent Boundary Layer flows: Boundary layer 7
concept, boundary layer thickness, displacement, momentum and
energy thickness. Momentum integral equation; drag on flat plate.
Boundary separation. Flow around immersed bodies- drag and lift.
Total 42
 ME-202:THERMAL ENGINEERING-I|
S. No. Contents Contact
Hours
1 Reciprocating Air Compressor: 7
Steady flow analysis, isothermal, adiabatic and polytropic compression;
single- and multi-stage compression, ideal intermediate pressure;
compressor clearance, volumetric and isothermal efficiency; minimum
work requirement of a compressor.
2 Centrifugal compressor: 5
Velocity diagrams, efficiency of compressor stage, choice of reaction
stage pressure rise, surging, multi-stage compressor, compressor
performance, vaccum pump.
Gas Power Cycles 8
Air standard cycle, Otto, diesel and dual cycles, P-V and T-s diagrams
of these cycles, efficiency, mean effective pressure. comparison of Otto,
diesel, dual cycles for same compression ratio and heat input, stirling
cycles, ericsson cycle, atkinson cycle, basic gas turbine (Brayton)
cycle (for open and closed systems), efficiency of gas turbine cycle
4 Gas Turbines: 10
Simple open and close cycle gas turbine, efficiency and specific
output of simple cycle, effects of regeneration, re-heating and inter
cooling on efficiency and work output, effect of operating variables on
thermal efficiency, air rate, work ratio; water injection,Advantages and
disadvantages of gas turbine; gas turbine components, performance
and application of gas turbine

ME-52

5 Gas Dynamics: 6
Fundamentals of gas dynamics, energy equation, stagnation
properties, isentropic flow through nozzle and diffusers, Introduction
to shock waves.
6 Jet Propulsion: 6
Introduction to jet propulsion, advantages and disadvantages of jet
propulsion, turbojet engine with and without after burner, turboprop, ram
jet, pulse jet, rocket engines - operation, solid and liquid propellants.
Total 42
 ME-206: KINEMATICS OF MACHINES
S. No. Contents Contact
Hours
1 Review of mechanics: Kinematics of a particle, time derivative of a 7
rotating vector, vector derivatives in a rotating system, kinematics of a
rigid body, Chasle's theorem, Coriolis acceleration, Euler's equation.
Introduction to mechanisms: Mechanisms and machines, Plane and
space mechanisms, different types of kinematic pairs, kinematic chain,
kinematic diagram, degrees of freedom, Grubler's equation, Grashofs
criterion, kinematic inversions of 4R, 3R-P, 2R-2P chains, velocity and
acceleration diagrams, instantaneous center method, Kennedy-Arnold
theorem.
2 Cams: Classification, Follower diagrams, construction of Cam profile. 7
High speed Cams. Cams with specified contours. Analysis of a rigid
Eccentric Cam.
3 Toothed Gearing: Law of gearing, spur gears, geometry of tooth 7

profiles, cycloidal and involute profile, minimum number of teeth on

pinion, interference, arc of contact, terminology of helical gears.
Gear trains: Simple, compound and epicyclic gear trains.
4 Mechanisms with lower pairs: Straight line mechanisms like 7
Peaucellier's mechanism and Hart mechanism, Engine indicator
mechanism, Steering mechanism of vehicles, Hooke's joint etc.
5 Friction: Pivot and Collar friction, clutches, belt and rope drives, 7
boundary friction, film lubrication, rolling friction.
6 Introduction to synthesis of linkages, use of software for motion and 7
interference analysis.
Total 42
 HU202: ENGINEERING ECONOMICS
S.No. Contents Contact
Hours
1. Introduction: Nature and significance of economics, Goods and 10
Utility, Basic Concept of Demand and Supply, Elasticity of Demand
Price elasticity of Demand, Cross elasticity of Demand, Production -
Production Function, Production Process and Factors of Production,
Market- Introduction to Monopoly, Perfect Competition, Oligopoly and
Monopolistic Competition, Cost Concepts- Opportunity Cost, Total Cost,
Average Cost; Marginal Cost; Life Cycle cost, Sunk Cost; Preparation
of Cost Sheet Profit Maximisation- numerical problem.

ME-59

2 Money- its evaluation and function, Bank- Commercial Bank and 10

Central Bank and brief idea about function of banking system:.
Tax and Subsidy, Type of Tax- Direct and Indirect, Monetary and fiscal
policy, Inflation and Business cycle, International trade, terms of Trade,
Gain from International Trade, Free Trade vs. Protection, Dumping.
Balance of Payment.
3 Role of Science, Engineering and Technology in Economic 12
Development: Seven salient Features of the Indian Economy; Inclusive
Growth; relevance for the Indian Economy; Globalisation & opening
up of the Indian Economy; GDP- definition and lts measurement; How
knowledge of engineering and technology may be used to improve
life at slums; Green Revolution and White revolution. Reasons for
their success and can we replicate them. Appropriate Technology &
Sustainable Development. Entrepreneurship: Macro environment for
promotion of entrepreneurship: How environment has changed after
advent of IT and Globalisation.
4. Elementary Economic Analysis: nterest formulas and their 10
Applications; Calculations of economic equivalence, Bases for
Comparison of Alternatives: Present Worth Method, Future worth
method, Annual equivalent, Internal Rate of Return; Business Risk;
Factors which should be taken care while deciding price of the product
in the market.

TOTAL 42
PE252: MANUFACTURING MACHINES
S. No. Contents Contact
Hours
1 Introduction to Machine Tools: Classification, similarities; various 7
cutting tools and cutting fluids: speed of cutting, feed rate, machining
rate and machining time.

ME-50

2 Lathe: Construction, important mechanisms viz. apron, tail stock, 7

head- stock, feed box, specification, operations e.g., taper turning,
eccentric turning, screw cutting.
3 Drilling machine: Construction, feed mechanism: Specification, 7
geometry and nomenclature of twist drill, operations e.g. reaming,
boring, tapping.
4 Milling machine: Construction, types specifications; cutters, dividing 7
head, simple compound and differential indexing; various operations:
Slab milling, angle cutting, slot miling, fly milling, slit gear milling, spur
and bevel, T- slot milling, nature of operations, up and down milling.
5 Shaper, Slotter, Planer: Construction, automatic feed mechanism, 7
quick return mechanisms: operations e.g., horizontal, vertical and
inclined machining, spline cutting, keyway cutting, contour machining.
6 Grinding Machines: M, N types and construction features, Operations 7
e.g. Plane, cylindrical, internal and centreless grinding, tool and cutter
grinding, grinding wheels- specifications, shapes, setting, dressing,
truing.
Total 42
ME-208: MANUFACTURING TECHNOLOGY-I
S. No. Contents Contact
Hours
1 Casting: Properties of mouldingg sand, Sand testing, Gating and risering 7
system, Principle, process and applications of Die casting, Centrifugal
casting, Investment casting, and Continuous casting, Melting of metal
for casting, Castingdefects their causes and remedies, Cleaning and
Inspection of castings, Foundry mechanization and layout.
2 Welding: Principle, equipment, and applications of Submerged Arc 7
Welding (SAW), Gas Tungsten Arc Welding (GTAW), Gas Metal Arc
Welding (GMAW), Plasma Arc Welding,
3 Ultrasonic Welding, Electron Beam Welding (EBW) and Laser Beam 7
Welding (LBW).Gas cutting and arc cutting of metals, Welding defects
their causes and remedies.
4 Metal Forming: Mechanical behaviour of metals in elastic and plastic 7
deformation, stresS-strain relationships, Yield criteria, Concept of flow
stress by true stress-strain curves
5 Hot Forming and Cold Forming, Analysis of important metal forming 7
processes like Forging, Rolling, Extrusion, Wire Drawing by slab
method, Sheet metal forming processes. Introduction to High Energy
rate forming processes.
6 Powder Metallurgy: Powder metallurgy process and operations, 7
Advantages, Applications and Limitations of powder metallurgy.
Total 42