ABOUT THE ERRORS OF MEASUREMENTS

To measure some physical quantity - it means to compare it with the other one from same
type taken as the unit of measurement.
From whatever precision measurement has not been made, the values obtained for the most
part different from each other in repeated measurements, or rather the coincidence of these
values is not obvious. Perform accurate measurement - this means being able to choose among
distinct numbers closest to the true value of the measured value.
The value of error admitted during the experiment depends on the method used, the accuracy
of measure instruments and the skill of the work of the observer. Errors made during the
experiment, by their character are divided into systematic and random.
Assume that zero point of the thermometer mistakenly moved to + 0.50 C. When working
with a thermometer the error will be systematic. Taking into account the errors made in the
calibration of the thermometer, you can get rid of the error. To do this, before the experiment is
important to check the thermometer.
If the bias is eliminated, there is only random error. The complete elimination of the random
error is not possible, but it is possible to calculate the degree to which this error affects the
measurement result.
Random error can be calculated as follows. Suppose that in direct measurements of a
physical quantity in the same conditions, the values a1, a2, a3, ... an are received. If one of the
numbers obtained during the repeated measurement is greater than the true value of the physical
quantity, someone other may be less. It is difficult to say which of the received physical quantity
values closer to the true value of this quantity.
According to the theory of probability among the values obtained by multiple
measurements, the number of values larger than the true value, and the number of values less
than the true value have the equal probability.
Therefore, the value closest to the true value of a physical quantity is the arithmetic average
of the numbers obtained in the measurements:
a1 + a2 + a3 +. . . ,+ an
a=
n
where n - the number of measurements.
By comparing the values obtained in repeated measurements of a physical quantity, with a
mean value, we get:
a−a 1=Δa 1 ;
a−a 2= Δa2 ;
a−a 3= Δa3 ;
. .. .. . .. .. . .. .. .. .
a−a n= Δa n
where Δa 1 , Δa 2 , Δa3 .. .. , Δa n - the errors made at each measurement separately.
These errors are called absolute error of each measurement.
Expression.
|Δa1|+|Δa 2|+|Δa 3|+. ..+|Δa n|
= Δa
n
It is called the average absolute error of measurement.
The probability theory shows that in cases where the number of direct measurement is very
large, the algebraic sum of positive and negative errors of the individual measurements is zero,
n
∑ ± Δai =0
those i=1 .
 Also, when the number of measurements are very large, errors with a large absolute value
are rare .
We cannot estimate the degree of measurement accuracy using only the value of the absolute
error of a physical quantity.
To assess the accuracy of the experiment uses the concept of relative error. The relative error
of a1, a2, a3, ... an, obtained from individual measurements of the physical quantity, are:
Δa 1 Δa2 Δa3 Δa n
, , , . .. ,
a1 a2 a3 an .
and the average relative error
Δa
Ε=
a (1)
For the determination of many physical quantities it is necessary to resort to the help of the
formulas. In this case, the error of experimental result is calculated, given the errors in the
measurement of separate values in the formula.
To calculate the error of measurement of any physical value determined by an indirect route, you
must:
1) take the logarithm of this formula;
2) differentiate the resulting expression;
3) replace the sign of the differential by the sign of the increment;
4) due to the fact that the greatest error is calculated, take all the errors with the sign (+).
Let us explain this with an example.
Assume that the Young's modulus is determined by the stretching.
It is known that the following formula is used
8 FRl
Ε=
πD2 ah
Take the logarithm of this formula to calculate the relative error,
ln E=ln 8+ln F +ln R+lnl−ln π −2 ln D−ln a−ln h ,
Then differentiate the resulting expression
dE dF dR dl dD da dh
= + + −2 − −
E F R l D a h

dπ
(Value π be ignored).
Replacing the sign (-) in front of with a sign (+) obtain the relative error in the determination of
the Young's modulus expression
ΔE ΔF ΔR Δl ΔD Δa Δh
= + + +2 + +
E F R l D a h

If in the experience you get the value :

F =1 ,5 H R =160 cm
D=0 ,8 mm h =30 mm
Δa=0 ,1 mm ΔD=0 , 01 mm
a=2 ,5 cm l=150 cm
ΔR=1 mm ΔF =0 , 01 H
Δh=0 , 5 mm Δl=0 , 1 cm
the error will be expressed as follows:
ΔF 0 , 01⋅100 ΔR 1⋅100
= =0 , 67 = =0 ,06
F 1, 5 %; R 1600 %;
 Δl 0 , 1⋅100 ΔD 2⋅0 , 01⋅100
= =0 , 07 2 = =2 , 5
l 150 %; D 0,8 %;
Δa 0 , 1⋅100 Δh 0 , 5⋅100
= =0 , 4 = =1 , 7
a 25 %; h 30 %;

As can be seen from these expressions, the relative error made in measuring of the wire
diameter, 35 times larger relative error made in measuring of its length. Clearly in this case there
is no point to measure the length of wire with such precision. , You should try to determine more
precisely the diameter of the wire to reduce experimental error. And for this reason, before you
begin the experience, it is necessary to take into account what the error can be done, and
depending on it to set the precision with which will need to measure the individual values.
 LABORATORY № 1
DETERMINATION OF THE MOMENT OF INERTIA OF THE SOLIDS USING A
TORSION PENDULUM
Objective: To study the method for determining the moment of inertia of the solid bodies of
various shapes using a torsional pendulum.
Accessories: torsional pendulum, loads of varying weight and shape, a stopwatch, an etalon
cylinder, caliper.
Works theory
By studying the motion of a material point, we use the value of the momentum, force, kinetic
energy. In translational motion, all points of the body move with equal speed and with the same
trajectory. And for this reason, the expression of momentum and kinetic energy of the moving
body are identical to expressions of material points.
With the rotational motion of the various bodies, rotors, generators, wind turbines and propellers
etc. we often meet in practice. The feature of rotational motion is that the body components,
describe concentric circles at various speeds. If the body performs rotational motion, there is a
need for the expression of various dynamic quantities through angular velocity which is the same
for all points of the body. In this regard such quantities as the torque value, the angular
momentum and inertia are considered.
As a characteristic of the distribution of mass, moment of inertia also characterizes the inertia of
a rotating body.
n
J=∑ m i r 2i J=∫ ρr2 dV
i=1 или V
where mi - mass of the particles constituting the body,
ri - the distance from these particles to the axis of rotation,
ρ - Density,
V - volume of the body.
Torsion pendulum - a body hanged on a thin thread in the gravity field. When rotating such body
around a fixed thread by a small angle in thread the torque proportional to the angle of rotation is
appeared. As a result, the body begins to perform harmonic oscillations around the thread
(Figure 1).
Apply to the body which commits the torsional oscillations, the basic equation
of dynamics of rotational motion. thread

d2 ϕ
M=J
dt 2 (1)
.
Where M - is a torque relative to the rotational axis,
Fig. 1
J - moment of inertia with respect to the same axis,
d2 ϕ
dt 2 - angular acceleration.
For small values of the angle the rotation torque of the elasticity is proportional to this angle
M =Gϕ . Where G - is called the module of torsion and has constant numerical value for
this thread. Taking this into account, the equation (1) can be written as
d2 ϕ d2 ϕ G
J⋅ 2 =−Gϕ 2
+ ϕ=0
dt or dt J (2)
 which is the differential equation of harmonic oscillations. Taking into account that
G
=ω2
J for torsional oscillation period the following expression is obtained

T=
2π
ω
=2 π
J
G √ (3)

Device description
The scheme of the device is shown in Figure 2. The device consists
of a base 1, counters with an arm 2, collet chuck 3, a metallic suspension
(thread) 4, disc 5 with two clamps, the etalon and the test loads. With
this setting you can determine the moment of inertia of any object with
mass not greater 5kg located in the center.
First defined by the moment of inertia of the device itself. For this
the disc is centered by means of clamps (Figure 2) about a vertical axis.
Then by turning the disc around this axis at a small angleϕ , achieve the
torsional oscillations. Using the stopwatch determine the time t0,
п 0=20−30 number of oscillations, while Fig. 2
necessary to perform
T =t /n
calculating the period of oscillation by the formula 0 0 0 . On the other hand the connection
between the period
T 0 of the device, its moment of inertia J 0 and modulus of torsion G is given
by

T 0 =2 π
√ J0
G (4)

This formula includes unknown quantities

J 0 andG . To determine them an etalon cylinder
1
J= mr 2
with a known moment of inertia is setting to disc 2

where m - is the mass of the cylinder, r - the radius. If the axis of rotation of the cylinder is
parallel to the axis of rotation of the device and the distance between them is d, then according to
Steiner's theorem the moment of inertia of the cylinder
1
J 1 = mr 2 +md 2
2 (5)
The period of the device with the etalon cylinder is calculated as

T 1=2 π
√ J 0+ J 1
G
From the expressions (4) and (6) we obtain
(6)

T 20 J 1
J 0= 2
T 1 −T 20 (7)
4 π 2⋅J 1
G= 2
T 1−T 20 (8)
 When the etalon cylinder is replaced by another load, the period of the device with this load
will be

T =2 π
√ J 0+ J
G (9)

Where J the moment of inertia of the load. Substituting the values

J 0 and G from (7) and
(8) into (9) we obtain the expression for

T 2−T 20 1 2 2
J= m( r +d )
T 21−T 20 2
(10)

Procedure and analysis

1. Align the installation. Turn the disc at a small angle ϕ to oscillate the system about a vertical
t n
axis. Measure by a stopwatch the time 0 in which 0 (about 20 - 30) oscillations are completed.
Calculate the period of oscillation of the device. The measurements repeated at least three times.
2. Measure the weight of the etalon and its radius. Set the etalon on a disk of the devise, so that
the etalon's symmetry axis was parallel to the axis of rotation of the device. Measure the distance
d between the axles.
3. Determine, as described in paragraph 1, the period T 1 of the system with the etalon load.
4. After removing the etalon from the disc , install the study load on it and determine the period
t
T=
of oscillation using the above method n.
T ,T ,T ,m ,r ,
5. Substituting the values 0 1 and d in the formula (10) calculate J .
6. The measurements were repeated 3-5 times obtained numerical values recorded in the table
and calculate the relative measurements error.

Measurement Table

№ T 0, s T1,s T ,s m , kg r ,m d ,m J , kg⋅m2
1
2
3

Questions to the lab. Kinematics of rotational motion. The basic equation of dynamics of
rotational motion, Steiner theorem, the moment of inertia of some bodies of regular geometric
shape.
Laboratory Work # 2
Determination of moment of inertia by the method of falling

Work Objective: To study a dynamic method of determination of the moment

of inertia.
 Accessories: Installation for determining of the moment of inertia, metallic
hoop, stopwatch, vernier caliper, ruler, loads of different masses..
Short theoretical information
The method of dropping is one of the methods of determining the
moment of inertia of solids. Its essence consists of the followings.
The device that define the moment of inertia consists of D-disk
which can rotate around the OO1 axis. For rotation of D-disc the
thin rope is wrapped around B-drum on OO1 axis. This rope threw
down from P pulley and m load attached to another end of rope.
Falling because of gravity load pull the rope and rotate B-drum and
D-disc around the axis. For keeping m load in motionless case there
is E mechanism. While the load is falling, the potential energy of
the load is spending to work done agents the friction force and to
increasing of the kinetic energy of all system . That is why
Ep = Ek1 + Ek2 +W (1)
In here Ep – potential energy of load at the beginning of motion, E k1 – is kinetic
energy of load m at the end of motion, E k2 –is total kinetic energy of rotation of
axis, drum and disc with body at the same time, W - work done agents the friction
force. If the moment of inertia of the disc I 0, the moment of inertia of the body
under research is I, then
mgh =mv2/2 + (I + I0 ) ∙ ω2/2 +W (2)
Here h- height of falling of load, m- mass of load, v- speed of load at the end of
way, ω- is angular speed of rotating motion of system at the same time. If we
assume the uniform accelerated falling
v=a∙t, h=a∙t2/2, hence v=2h/t, ω=2h/(r∙t) (3)

Here r-radius of drum. Considering (3) and (2)

mgh =2mh2/t2 + 2(I+I0)∙h2/(r2∙t2) + W (4)

Writing this equation for two different loads and subtracting the second equation
from the first, we get:

g (m1-m2) = 2h (m1/t12-m2/t22) + (I0+I)∙ 2h (1/ (r2∙t12)- 1/ (r2∙t22)) (5)

We may rewrite it
]
I0+I= r2 [g (m1-m2) – 2h (m1/t12-m2/t22) / 2h (1/t12- 1/t22) (6)

Here t1 and t2 are dropping time of m1 and m2 loads from h height respectively. For
defining moment of inertia of body for the first time this body is removed from D-
disc, then for a second time the body is placed on the disk.

The work progress

1. Define the radius of drum (r) with vernier caliper.
2. Set the body for defining of moment of inertia on a disc and fixing with
clamp.
 3. Wrap the rope around B drum, one of the loads suspend to the other end of
rope, lift it up and fix at this position.
4. Release the disc from the clamp and allow the load falls. Measure the time
of dropping. Repeated the experiment with second load.
5. Calculate I0 + I by formula (6).
6. Remove the test body from the disk D, keep the clamps in the same position
and repeat the measurement, as mentioned above in items 3 and 4. Calculate
I0 by formula (6), considering that I=0.
7. Calculate value of I as difference between measurements with body and
without body.
8. Calculate the percentage uncertainty of experiment.

Data tables

For case with body on disc D

# m1, kq m2, kq h, m t1, san t2, san I+I0, kq∙m2
1.
2.
3.

For case with empty disc D

# m1, kq m2, kq h, m t1, san t2, san r, m I0, kq∙m2
1.
2.
3.

Questions for laboratory work. Kinematics and Dynamics of rotating motion.

The Kinetic energy of rotating body. Moment of inertia of some bodies which have
regular geometric shape.

LABORATORY № 3
DETERMINATION OF THE FREE FALL ACCELERATION BY TURNED
PENDULUM
Objective: To determine the free fall acceleration using the turned pendulum.
Accessories: Turned pendulum, stopwatch, ruler.
Works theory
Physical pendulum is called a rigid body capable to oscillate around a fixed point that does not
coincide with its center of mass (Fig. 1). When turning the pendulum from the equilibrium
position at an angle ϕ , a torque tending to return the pendulum to its equilibrium position
М =Jβ is appeared, where J - the moment of inertia of the pendulum about the axis passing
through the suspension point and β the angular acceleration of the pendulum obtained by force
Р1 - the component of the gravitational force. This moment is:

M=−P1 l=−Pl sin ϕ=−mgl sin ϕ

in the case of small oscillations sin ϕ=ϕ and M=−mgl ϕ . The sign "-" indicates that the force
has such a direction that tends to return the pendulum to its equilibrium position, and is similar in
this respect to the quasi-elastic force. Given that β=ϕ , we get the equation
Fig. 1
'' mgl
ϕ + ϕ=0
J (1)
When comparing of this expression with the differential equation of harmonic oscillations get
mgl
ω 2=
J
Thus, the period of physical pendulum executing small oscillations is determined by the
formula:
T =2 π
√ J
mgl (2)

where m - the mass of the pendulum, l - the distance from the center of gravity to the axis (point
O) of rotation of the pendulum. If we compare the expression (2) with the expression
Т =2 π
√l
g - a mathematical pendulum period, we see that the mathematical pendulum with the
J
ml will have the same oscillation period, as the physical pendulum. Quantity l пр
l np=
length
called the reduced length of the physical pendulum. Calculations show that the reduced length of
any physical pendulum is always greater than the distance from its center of gravity to the axis of
rotation. If O is the point of suspension (1), C - center of gravity, the distance OO 1 equal to the
reduced length OO 1 >OC . O1 point on the straight line connecting the point of suspension to
the center of mass (in this case the center of inertia and the center of gravity of the pendulum are
the same), which lies at a distance of reduced length from the rotation axis, called the swing
center of a physical pendulum. When hanging pendulum in swing center the reduced length, and
thus the oscillation period will be the same as at the beginning. Therefore, the point of
suspension and the swing center exhibit the property of reciprocity: when transferring the point
of suspension to the swing center the previous suspension point becomes the new center of the
swing.
Determination of acceleration of gravity with the help of the so-called turned pendulum is
based on the property of reciprocity. Revolving pendulum consists of a metal rod longer than one
meter with applied millimeter divisions on the surface, which has two parallel fixed near its ends
bearing prisms 1 and 2, on which it may alternatively be suspended.
Heavy loads A and B can be moved and fixed along the pendulum. By shifting loads we get
that when hanging pendulum on any of the prisms the oscillation periods T 1 and T2 are equal.

Then the distance between the support ribs of prisms will be equal np
l =L . In this case
T =2 π
and hence
√ L
g

4π2 L
g=
T2 (3)
Because it is difficult to achieve completely equality of periods T 1 and T2 oscillations then in
practice try to achieve that the difference between them is as small as possible. In the
calculations, instead of T put arithmetic mean of T1 and T2,
 4 π2 L 16 π 2 L
g= =

( )
2
T 1 +T 2 ( T 1 +T 2 )2
2 (4)

Procedure and analysis

1. Put the pendulum on the prism 1, to measure its period T1 based on 40 - 50 vibrations.
2. Rotate and hang the pendulum on the prism 2 and again, as mentioned above, calculate its
period T2. Loads should not be moved because they were placed so that the periods T1 and T2
would differ a little from each other.
3. Measure the reduced length between the prisms 1 and 2.
4. Calculate the acceleration of free fall by the formula (4).
5. Calculate the relative error of the measurements.

Measurement table.

№ L ,m T1,s T2,s g, m/s2

1.
2.
3.

Questions to the lab. Harmonic oscillations. The energy of the harmonic oscillation.
Mathematical and physical pendulums.

LABORATORY № 4
DETERMINATION OF THE DAMPING COEFFICIENT, LOGARITHMIC
DECREMENT AND THE QUALITY FACTOR OF THE OSCILLATING
SYSTEM
Objective: To determine the basic physical quantities characterizing the damped oscillations.
Accessories: Physical pendulum, stopwatch, scale for determining the oscillation amplitude.
Works theory
In any real oscillating system, a resistance force is always available, and mechanical energy,
which we given during the initial excitation of vibrations, gradually transformed into heat
energy. The result of this is that the vibrations are damped. Under the amplitude of damped
oscillations, we understand the greatest deviation from the equilibrium position in one period.
The friction forces are in difficult way depend on the speed, but small oscillations when the
velocity is small in absolute value, the friction force is proportional to velocity.
dx
f X=−b
dt
where b - coefficient of friction. In this case, the dependence of displacement of the
oscillating body of the time expressed by the formula

.
x= A e−βt sin( ωt+ ϕ )
0 0
and for the angular frequency obtained by expression
ω=√ ω 20−β 2
b
β=
where 2 m - damping coefficient, ω 0 - specific angular frequency of the oscillating
system. The amplitude of damped oscillations decreases exponentially
A=A 0 e− βt
 The ratio of amplitudes corresponding to moments of time, differing by a period called the
damping coefficient, and its logarithm - logarithmic decrement.
A 0 e− βt
λ=ln − β (t +T )
= ln e βT = βT
A0 e
Logarithmic decrement is inverse by value to the number of
vibrations made during the time for which the amplitude
decreases by e=2 .71 times. The amplitude ratio corresponding
to moments of time that differ t =TN (during this time N
fluctuations are committed ) is equal
А0 е−βt
К= −β (t +TN )
=e β NT
to A0 e (1)
and its logarithm: ln K =β NT =λN
ln K 2 , 31 lg K
λ= =
then N N (2)
t
T= Fig. 1
By calculating the expression N ,
we can determine the value of the damping coefficient from the formula
λ
β=
Т (3)
To characterize the oscillating system one value is often used
π
D=
λ (4)
called Q-factor of the oscillating system. The quality factor is proportional to the number of
oscillations made by the system during the time for which the amplitude of the oscillations
decreases by a factor e.

Procedure and analysis

1. Dismiss the pendulum (Figure 1) from the equilibrium position at 7-8 cm., let it to oscillate.
2. Fix the value of (А1), one of the maximum deviation of the pendulum from the equilibrium
position. From this moment, count the number of oscillations N, t time, spent on it, and fix the
maximum deviation of the pendulum (А2) at the last swing.
А
К= 1
3. Calculate the ratio А2 , and then take the logarithm ln K and calculate.
4. From the known values of the variables t, N, T and lnK calculate the logarithmic decrement λ ,
damping factor β and the quality factor D.
5. Repeat the measurement 4-5 times to determine the average value, and. Calculate the relative
measurement error.
Measurement table.

№ A1 , A2 , N t, s T,s λ β D
cm cm
1.
2.
3.
Questions to the lab. Harmonic oscillations. The differential equation of harmonic oscillations.
Mathematical and physical pendulum. Gravitational interaction. Acceleration of gravity.
 LABORATORY № 5
STUDY OF THE IMPACT MECHANISM
Objective: To study the interaction of bodies, check the laws of conservation of momentum and
energy.
Accessories: Installation for the study of the impact mechanism.
Works theory
Collision - a short-term interaction of bodies, resulting from their contact. Two cases are
considering when the balls collide, one of which - an elastic collision, the other - inelastic.
Considering the elastic collision of balls, and taking the system as a closed , we can calculate
the speed of the balls after the collision by applying the
momentum and energy conservation laws. In an elastic
collision of balls the force of collision depends on the mass
and speed and on the values characterizing the elastic
properties of balls. The following installation is using to
determine the time of collision. Steel balls A and B of equal
masses are suspended on electricity conducting non-
extensible threads. When they are in contact the circuit with
the galvanometer G, resistance R and capacitor C connected
in series is closed (Figure 1).
When key К 1 is closed and the key К 2 in position 2 by
writing the equation of Ohm's law for NOKZ circuit, we
obtain an expression for the time of collision
q0
t =CR ln Fig. 1
q0 −q
Or
q
t=2 .3 CR lg 0
q0 −q
q
where C - electrical capacitance of the capacitor, 0 - the initial charge on the capacitor, which
passes through the galvanometer within one strike of balls.
Because the values on the galvanometer is proportional to the charge passing through it, we get
the expression for the collision time
n0
t=2 .3 CR lg
n0 −n (1)
It is necessary to know the speed of the ball to determine the impact force.
Suppose that a ball deflected by an angle α from its equilibrium position
A, set aside to the D position, and then is raised to a height h (Figure 2).
Returning to the equilibrium position at point A it gains the speed

υ=√ 2 gh
As can be seen from the OND triangle
l−h h
cos α= =1−
l l Fig. 2
Hence we obtain for h:
α
h=2l sin2
2
Given this, an impact rate:
α
ϑ =2 sin √ gl
2 (2)
If at the moment of collision, one of the balls was at rest, according to Newton's second law
mϑ
f=
f⋅t =mϑ and t (3)
where f - the force of impact.

Procedure and analysis

1. Close the К1 key using the key К2, placing it in position 1, connect the current source Е1 to
the capacitor C (Figure 1). The capacitor will be charged.
2. Disconnecting the key К1 place К2 key in position 2, closing the condenser with a
galvanometer ..
3. Closing the key К1, determine the value on galvanometer n0.
4. Remove key К2 to 1 to charge the capacitor. Disconnecting К1 move К2 key to position 2.
5. Move the ball A to the electromagnet D and close the К3 key.
6. Disconnecting the К3 key, allow the ball A to move. At a meeting of balls A and B
capacitor will partially discharged through the galvanometer. Note value on galvanometer n.
7. According n0 and n calculated t by the formula. (1).
8. Determine the angle α when the ball A is in front of the electromagnet D. Knowing this
angle calculate ϑ by formula (2).
9. Knowing the massm of the ball, ϑ and t , and using the formula (3) calculate the impact
force.
10. By changing the position of the electromagnet, change the angle α and repeat the
experience. Record the measurement results in the table and calculate the relative
measurements error.

Measurement table.

№ п0 п α t ϑ m/s f.N
1
2
3

Questions to the lab. Newton's Laws. The law of conservation of momentum. The mechanical
energy. Elastic and inelastic collision of balls.
Laboratory work # 6
DETERMINATION of the UNKNOWN FREQUENCY of OSCILLATION
by BEATS.
Work Objective: To study the effect of interference of the same directed oscillations
Accessories: Two acoustic generators, oscilloscope.

Theory.
Consider the adding of two harmonic oscillations of the same direction, with slightly
different frequencies. Denote the frequency of first oscillation ω1 = ω, the second ω2 = ω + ω
. The amplitudes of both oscillations will assume the same and equal to
a. Since the oscillation frequency slightly different, we can always choose the origin of time, so
that the initial phases of both oscillations be zero. Thus both the wave equation are as follows:
 and
Adding these two expressions, and using trigonometric formula for the sum of cosines, we
get:
Δω
х=х 1 + х 2 =2 а cos t cos ωt
2 (1)
Δω
(In the second factor we neglect the term 2 in comparison with ω.)
As seen from the expression (1), the multiplier

(2)
is changing periodically with time, and it is the amplitude of the resulting oscillations.
(Figure 1).

Fig. 1

Function (2) - is a periodic function with a frequency of 2 times the frequency of the
expression under module mark. Hence:
Δω ( ω2 −ω1 )
⋅T = T =π
2 2
and
2π
T=
ω2 −ω 1

At last

(3)

Thus, the frequency of amplitude pulsations - it is called beat frequency - equal to the
difference between the frequencies of oscillations. Oscillations with pulsating amplitude are
called beats (Figure 1).
Suppose that we need to determine the frequency of the source of unknown frequency .
If we use a second source of oscillations with a certain frequency, varying over a wide range, it
is possible to choose a frequency , close to so that the beat of frequency will be
observed. By increasing the frequency of the second source we can again receive the beats with
the same frequency f. But at this case , where is the frequency at second time.
From the last two equations we get

(4)
 Installation diagram consisting of the oscilloscope EO and two generators, is shown in
G
Figure 2. Generator x is used for forming oscillations of unknown frequency and the G
respectively for oscillations of known frequency.

Fig.2

Progress.

1. Connect both generators to the same input "X" of the oscilloscope. With the help of the "exit
control" handle to reduce the voltage of generator's signal to zero. Switch on the Generator
G x for forming oscillations of unknown frequency. By adjusting the "Y" axis amplification
of oscilloscope set the amplitude of the oscillations of an unknown frequency about 1.5 - 2
G
cm. Switch off Generator x then switch on the Generator G and set frequency about 10
kHz. Without changing the amplification of the oscilloscope by the "Output" handle of
generator set the oscillation amplitude equal to the amplitude of oscillations of unknown
G
frequency. Switch on the generator x .
2. Set the frequency range on the oscilloscope at the level 5000 Hz. Changing the frequency of
generator G in the range of 0,8 -12 kHz to get beats on the screen at first frequency .
3. Turn the control knob of the generator and get on the screen next beats with the same beats
frequency corresponding to the frequency . Use the formula (4) and these values to
calculate the unknown frequency.
4. Repeat the experiment several times. Calculate the relative measurement uncertainty.

Data table

№
, Hz , Hz Hz
1
2
3

Questions to the laboratory work.

Harmonic oscillations, superposition of the identical directed oscillations. Beats.

LABORATORY № 7
DETERMINATION OF UNKNOWN FREQUENCY BY ADDITION MUTUALLY
PERPENDICULAR OSCILLATIONS
Objective: To study the process of addition mutually perpendicular oscillations.
Accessories: The oscilloscope and two generators.
 Works theory
The simplest vibrations are harmonic oscillations, ie, such fluctuations, in which the fluctuating
value varies with time according to a sine or cosine law. Let us assume that a material point
performs harmonic oscillations in two mutually perpendicular directions, which are described by
the equations
x= A x cos ωt and y= A y cos(ωt +α ) (1)
By addition of these fluctuations, we obtain the equation of the trajectory of motion of a material
point. We obtain the equation of the trajectory
(2) by elimination of time t from the equations (1)
x2 y 2 2 xy
2
+ 2− cos α =sin 2 α
Ax Ay Ax Ay (2)
Equation (2) is the equation of an ellipse, and its axes are oriented with respect to the coordinate
axes x and y arbitrarily.
Ay
y= ⋅x
When α =0 (the phase difference is zero), the equation (2) takes the form Ax that is
the equation of a straight line (Figure 1)
π
α =±
In the case of 2 the equation (2) becomes
2 2
x y
2
+ 2 =1
Ax Ay (3)
ie in the equation of the ellipse, which half-axis is equal to the amplitudes of fluctuations (Figure
2). If
A x =A y =R , then (2) goes to x 2 + y 2 =R2 , that is the equation of a circle with radius R.

Fig. 1 Fig. 2
If the frequencies of perpendicular
oscillations are not the same, the trajectory of the resulting motion is
complex curves called Lissajous figures. Figure 3 shows one of them,
π
when frequency ratio 1: 2 and the phase difference 2 .
Assume that the ratio of the oscillation frequencies is a rational
п х and п у Fig. 3
number, and can be represented as a ratio of whole numbers
п х ωу νу Тх
п= = =
Then п у ωх ν х Т y (4)
Based on the equation (4) we can write:

п х Т у =п у Т х=t 1 (5)
 This means that after doing
п х vibrations along the X-axis and п у oscillations along the Y-
axis during the time t 1 the point goes back to its original position. In the next period of time
t 2=t 1 the oscillation is repeated again and we get a stable picture of the Lissajous figures that
n n
crosses arbitrary axis parallel to the x and y axes, respectively, x and y times. Using equation
(5) we can calculate the unknown frequency
ν y using a known frequency ν x .
n
ν y = x⋅ν x Г х
ny (6)
Scheme of installation is shown in Figure 4. It consists of a generator
G х of known

frequencies
ν х , oscilloscope EA and generator G х of unknown frequencies ν у .

Fig. 4
Procedure and analysis
1. Assemble the circuit according to Fig. 4. Turn on the oscilloscope, to focus and bring the light
spot in the center of the grid.
2. Turn on both the generator. Give to oscilloscope the frequency
п у from generatorG у . Turn the
handle of the generator
G х frequency, to achieve the appearance of Lissajous figures on a screen.

3. Determine the number of intersections with the axes x

п х and y п у , and calculate the
ν
unknown frequency у by the formula (6).
4. Get another Lissajous figure by changing the frequency of the sound generator . Then, from
the formula (6) re-calculate the required frequency
νу.
Draw the resulting figures.

Measurement table.

№ First Lissajous Second Lissajous Third Lissajous

figure figure figure
пх
пу
ν х , Hz
ν у , Hz

Questions to the lab. Simple harmonic oscillations, Addition of perpendicular oscillations.

Lissajous figures.

LABORATORY № 8
DETERMINATION OF YOUNG'S MODULUS BY BENDING METHOD
Objective: The study of elastic deformation. Acquaintance with one of the methods to determine
the Young's modulus.
Accessories: Device to determine the Young's modulus, caliper or micrometer, loads.
Works theory
Under the action of external forces bodies are deformed, i.e. their size and shape are changed
. If after the termination of forces action the body takes the original size and shape, the
deformation is called elastic.
Elastic deformation occurs in the event that the force which caused the deformation does not
exceed a certain, specific to each individual body limit (known as the elastic limit).
If you exceed this limit, the body gains residual or plastic strains that persist even after the
termination of the force on the body.
Within the elasticity the deformation obeys Hooke's law. If the rod with length
l 0 and cross
section S under the force F is stretched by Δl , according to the law.
F Δl
=E
S l0 (1)
F
=σ ε =Δl /l 0 - the relative strain, E - Young's modulus. Given
where S - the mechanical stress,
these designations the Hooke's law can be written as
σ =E⋅ε (2)

From (2) it follows that the Young's modulus is equal to normal stress when the relative strain is
Δl
ε= =1
equal to one l0 (
Δl=l 0 and l=2 l 0 ). Where l - the final length of the rod.
Young's modulus can be determined in several ways. One of these methods is a method of
bending.
In a device the rod is located on two vertical supports that are on a solid plate (figure 1).
Two prisms arranged so that their edges are parallel and the distance between them is equal to L.
There is a rod on prisms with the load F suspended in the center of it (figure 2).

Fig. 1 Fig. 2
In this case, the bend of rod
1 PL3
ΔS = ⋅
E 4 ab 3 (3)
Where E - Young's modulus, a a is the width, b is the thickness, of L - the
length of the rod. From this formula, we can calculate the numerical value
of E.
PL 3
E=
4 ab 3 ΔS (4)
Bend of rod x is determined by "indicator". "Indicator" is showed on figure 3. Using this device
we can determine the bend with accuracy of 10 mm. The revolution of huge arrow corresponds
to 1 mm. Therefore, each division of the scale corresponding to huge arrow is 0.01 mm. Small
arrow shows accuracy the bend up to 10 mm.
Fig. 3
Procedure and analysis
1. Measure the width and thickness of the rod, and also, placing the rod on the prisms (the ends
of the rod should equally extend beyond the prisms), measure the distance between the prisms.
2. Mark the indication of the indicator by placing various loads on the suspension in the middle
of the rod.
3. Calculate the deviation (x) for each weight from expression (4).
4. Repeat the experiments for each load several times. Calculate the relative error according to
the results obtained from the experiments.

Measurement table

№ L, m a, m b, m F, N x,m E, Pa

1.

2.

3.

Questions to the lab. Deformation of rigid bodies. Hooke's Law. Stress diagram.
Laboratory Work # 9
Determination of Cp/Cv ratio by speed of sound in gas

Work Objective: To study methods to measure specific heats of gases.

Accessories: Oscilloscope, a sound generator, a microphone and a tube
connected to the phone.
Short theoretical information

From acoustic known that the sound speed v in the elastic medium with a
density ρ defined by the relation

υ=
√ 1
αρ (1)
 where α - the coefficient of elasticity of the medium. Considering the
1
α=
relationship between α and the gas pressure P in the form of γP the formula
for velocity may be written as

(2)
where γ = Cp/Cv - is polytrophic (adiabatic) index and equal to the ratio of
molar specific heats of the gas at constant pressure and volume. From the ideal gas
law for density we can get

(3)
Substituting (3) into (2) for the speed of sound in the gas we get

υ=
M√
γ RT

Mυ2
(4)

γ=
and RT (5)
where R- universal gas constant, M is the molar mass, T the absolute
temperature.
Hence for determining the ratio of specific heats it is necessary to know the
temperature and the speed of sound in the gas. The oscillations of sound source
excited in an elastic medium, due to the interaction between neighboring particles
are transferred to other particles and thus the propagation of oscillation at a certain
speed occurs in environment. This process is called the wave process or simply
wave.
The particles of the medium in which the wave propagates, are not transferred
by the wave, they only oscillate about their equilibrium positions. Depending on
the direction of oscillations of the particles with respect to the direction of wave
propagates, there are two kinds of wave: longitudinal and transverse waves. In a
longitudinal wave, particles of the medium oscillate along the direction of wave
propagation. In the transverse wave medium particles oscillate in the perpendicular
direction to the wave propagation. Sound waves in liquids and gases are
longitudinal, and in solids medium - both longitudinal and transverse.
When the sound passing through air the alternating compression and rarefaction
regions of particles are created and moving in the direction of propagation of the
oscillations with speed v. The distance between the two nearest points, oscillating
in the same phase, called the wavelength λ. In the longitudinal wave it equal to the
distance between the centers of two neighboring compressions or rarefactions of
particles (Figure 1a), and in a transverse wave between adjacent crests or troughs
(Figure 1b)
 Figure 1.

If sound wave faces with some barrier on its path the wave is reflected in the
opposite direction. The incident wave and the reflected wave superimposed on
each other and form a standing wave. The points where the amplitude of oscillation
of standing wave becomes zero are called nodes. Points where the amplitude of
oscillation reaches a maximum value are called antinodes of a standing wave. All
points between two adjacent nodes, oscillate in phase (i.e., in the same phase).
Points which lie on opposite sides of the node oscillate in antiphase.

Figure 2
As seen from Figure 2, the distance between neighboring nodes, as well as the
distance between neighboring antinodes is equal to λ/2, where λ - the sound
wavelength. That is, the length of the standing wave will be equal

(6)
As it is known, the speed v of the wave of frequency f determined by the
formula
v= λ∙f (7)

Taking into account expression (6) in (7) we have:

(8)

Hence, to determine the velocity of sound in the medium is necessary to know

the length of the standing wave and the frequency of sound.
If the sound waves propagate in a medium in the direction of the x-axis, arising
here standing wave described by the equation
2 πx
ξ=2 a cos cos ωt
λ
where
2 πx
A=|2 acos |
λ
the amplitude of the standing wave.
2 πx
=±πn
λ
 At points where (n=0,1,2,3...) the oscillation amplitude reaches a maximum

value 2a.

These points are called antinodes of a standing wave. From the condition of
maximum coordinates of antinodes can be obtained

(9)
Thus, determining the position of the antinodes of the standing wave, it is
possible to calculate the length, and then the speed of the sound wave.

Installation Description

Installation diagram is shown in Figure 3. Sound head T connected to the sound

generator produces sound waves of known frequency. These sound waves
propagating in the sliding metal tube, caught by microphone M.

Figure 3

Arising in the microphone M audio signal is observed on an oscilloscope

connected to microphone. Telephone and a microphone connected to the metal
sliding tube by a thin rubber tubing. Sound vibrations created by phone, traveling
in the tube and are reflected from the opposite end. If the tube fits a whole number
of half-waves, they are superimposed and form a standing wave. There are two
ways to get a standing wave in the tube:
1) by changing the frequency of the generator of acoustic vibrations
2) by changing the length of the tube
In this work we use the second method.
Using the condition (9) the value of x max and the corresponding value of λ are
determined. On the basis of (7) and (5) the speed v and the ratio of specific heats γ
are calculated.

The work progress

9. Assemble the installation according to the diagram on Figure 3, connect
oscilloscope and sound generator to the AC power supply. Give them 5-6 minutes
to warm up.
10.Connect sound head T to the output terminals of the sound generator and the
microphone to the vertical input of an oscilloscope, and to ensure that the picture
on the screen looked like stable sine wave. Adjust frequency of the sound
generator, so that on the oscilloscope observed oscillations of sufficient amplitude.
By varying the length of the sliding tube to achieve obtaining several consecutive
stable sinusoidal patterns with maximum amplitude.
11.At the moment of obtaining the maximum amplitudes stop to sliding of the tube
and measure their positions X according to the divisions marked on them.
12.According to the value of X calculate the λ value by the formula (9).
13.Knowing the λ, calculate the speed of sound by formula (7) and according to
formula (5) to calculate the γ.
According to the formula i+ 2
γ=
i
calculate the number of degrees of freedom i.
14.Repeating the experience for different sound frequencies to calculate the absolute
and relative measurement error.

Data Table

№ f, Hz. X1, m X2, m λstand, m λ, m γ i

1.
2.
3.
Questions for laboratory work.
The wave process. Wave equation. Standing waves. The specific heat of an ideal
gas at constant pressure and volume, their relationship with the number of degrees
of freedom.

LABORATORY № 10
DETERMINATION OF THE RATIO OF HEAT CAPACITIES OF GASES BY
CLEMENT – DESORMES METHOD
Objective: Learning the method of Clement - Desormes - determination of the ratio of heat
capacities of gases and the determination of this ratio for air.
Accessories: Glass bottle with capacity of 5 - 6 cubic meters, manometer, air pump.
Works theory
A physical quantity which is numerically equal to the amount of heat which must be transmitted
to 1 kg of body weight in order to change its temperature by 1 ° C, is called the specific heat of a
substance (c). Physical quantity that is numerically equal to the amount of heat that is necessary
to transmit to one mole of a substance to change its temperature by 1 ° C, is called the molar heat
capacity of the substance (C). If the molar mass of a substance is equal to M, the relationship
between the molar and specific heat capacity is described by
 С=Мс (1)
The relationship between the specific heat at constant pressure (cp) and volume (cv) with the
molar heat capacity at constant pressure (Cp) and volume (CV) is similar to the expression (1),
ie,
Cv = M cр and CV = M cV (2)

If the gas is heated at constant volume, all the amount of heat goes to increase its internal
energy. When heated, the gas at a constant pressure one part of the supplied heat goes to increase
its internal energy, a part - to perform work on the gas expansion. Therefore, Cp> Cv. These heat
capacities are related to the number of degrees of freedom (i) of molecules with the following
relationships:
i i R i+2 i+ 2 R
Cv= R cv = C p= R c p=
2 (3) 2M 2 2 M

From these relations can be seen that Cp = Cv + R, where R - universal gas constant.
The number of degrees of freedom of a mechanical system is the number of independent
variables, with the help of which can be set the position of the system. Taking into account the
expression (3) we obtain for the ratio of heat capacities:
Cp cp i +2 (4)
γ= = =
Cv cv i
Measurement of specific heat capacities of gas, and in particular at a constant volume seems
difficult. To do this, we need to fill the certain volume container with a gas. Because this mass of
gas is much less than the mass of the container, the amount of heat required for heating the gas is
many times smaller than the quantity of heat required for heating the cylinder. Therefore, the
amount of heat received by gas is less than the error of experience. In the measurement of the
specific heat at constant pressure Ср, the heated gas passing through a coil placed in the
calorimeter at constant pressure, gives a certain amount of heat to calorimeter. Undoubtedly, in
this case the mass of gas passed through the coil must be greater than the mass of the coil, and
the measurement of Ср will be more accurate. In order to solve a number of physical problems it
is necessary to know the value of the ratio of specific heats γ . On the other hand, if it is known
γ, we can calculate Ср from experience, and then СV calculate. One of the methods of
determination the ratio
C p /C v is the method by Clement - Desormes.

Description of installation .
Installation diagram is shown in Figure 1.
A gas can be pumped into the glass balloon with a capacity of 15 - 20 liters by the pump, in
particular an air under pressure Р1. The difference between Р1 and Р0 (atmospheric pressure) is
fixed by manometer M coupled with the balloon.
 PUMP

Fig. 1
If h1 - the difference in liquid level in manometer, expressed in units of
pressure, then
P1=P0+h1 (5)
Compressed in a cylinder to a pressure Р1 gas is heated, but after some time, due to the
thermal conductivity of the material of the vessel, it becomes equal to the ambient temperature.
At this point, valve К1 is quickly opened and closed, which leads to the adiabatic expansion of
gas.
The volume of gas is equal to the volume of the vessel V at pressure Р1. After opening the
tap К1, the gas partly exits to the tube of manometer, and partly remains in the balloon.
Obviously, the gas pressure on both parts are equal atmospheric. The volume of the gas V 1
becomes equal to the sum of the volumes V, of gas remaining in the balloon, and the volume of
gas that is outflowed from the balloonV 2
V 1 =V +V 2
As noted above, when opening the tap К 1, the adiabatic expansion of the gas takes place,
whereby the gas in the cylinder is cooled below room temperature. Thus the gas moves from the
state (Р1,V ) to the state of (Р0, V2). If we close the valve К 2, after some time the gas in balloon
has reached room temperature, whereby the pressure Р 2 becomes higher than the atmospheric
pressure. The difference between Р 0 and Р2 is equal to the difference in height h2 of fluid in
manometer M.
P2 =P0 + h2 (6)
Ultimately, the gas pressure becomes Р2 and the volume V1. Because the temperature and the
mass of gas remained the same at the beginning and the end of the experiment , the process can
be considered isothermal and can be described with the Boyle - Mariotte equation :
P1V= P2V1 (7)
The adiabatic expansion from the state (Р 1, V) to the state (Р0, V1) is described by the
Poisson equation
P1 V γ = P0 V 1γ (8)
Raising the degree of the equation (7) by γ and dividing it by the equation (8), we obtain:
P γ1 P γ2
=
P1 P0
Taking the logarithm of this expression:

γ ln P1−ln P 1=γ ln P2 −ln P0

And for γ :
 ln P 1−ln P0
γ=
ln P 1−ln P2 (9)

Because the difference (Р1 –Р0) and (Р1, Р2) has very small values, then with a small error the
quation (9) can be rewritten as
P1 −P0
γ=
P1 −P2 (10)
If we substitute the values of Р1 and Р2 from the formulas (5) and (6) to the formula (10), we
obtain
P0 + h1−P 0 h1
γ= =
P0 + h1 −( P0 + h2 ) h 1−h2 (11)
Procedure and analysis
1. The air is blown in to the balloon with the pump through the tap К2 until the fluid level
difference becomes equal to 10-15 cm. Then close the tap К2 and note in a few minutes the
established difference in liquid levels in the manometer h1.
2. Open the tap К1 and close quickly when there is the equality of fluid levels in the manometer.
Wait 2-3 minutes and after the gas temperature reaches room temperature, write h2 from
manometer.
3. Substituting numerical values h1 and h2 in the formula (11), calculate the value γ .
4. Repeat the experience 8-10 times, calculate the mean value of γ , absolute and relative
experimental error.

Measurement table.
№ h1, sm h2, sm γ i
1.
2.
3.
..
10

Questions to the lab. Adiabatic process and isoprocesses. Poisson equation and the
consequences from it. The internal energy and heat capacity of an ideal gas.
Laboratory Work # 11
Determination of viscosity of liquids by Stokes's method
Work Objective: Study of basic laws of motion of viscous fluids and empirically determination
of the coefficient of internal friction.
Accessories: Investigated liquids, beaker, an aqueous solution of copper sulfate, stopwatch,
accurate scales and weights.

Short theoretical information

When fluid flow friction occurs between its adjacent layers as they slide past one another.
This force is called the internal friction or viscosity of the fluid. The higher internal friction
forces, the higher viscosity of the fluid and the greater the fluid behavior deviates from the ideal.
Newton found that the friction force between the fluid layers is described by the following
equation:
v
F f =η( )Δ A (1)
Δx
 v
where A- the contact area between the layers, - the velocity gradient is equal to the
Δx
change in the velocity with position as measured perpendicular to the direction of velocity, -
the internal friction coefficient which characterizes fluid viscosity, and depends basically on the
kind of liquid and temperature. Coefficient of internal friction (viscosity) is equal to the frictional
force acting on a unit area parallel to the layers if velocity gradient equal to one unit.
The SI unit of  is: [] = Pa∙s.
Viscosity of fluids can be calculated in various ways, one of which is the method of Stokes.
This method is based on the occurrence of friction forces when solid body moving within the
liquid. Stokes found that the force depends on the size and shape of the body, the speed of the
body in fluid, and on the viscosity of the fluid. In particular, the friction force at low velocities of
motion of the ball of r radius inside the liquid is given by:
F St =6 πηrυ (2)
When the ball moves in a liquid gravity force W, the force of
internal friction (drag force) and the Archimedes's buoyant force
are acting on it. (Fig.1). In this case, the equation of a ball
motion is described as:

ma = W - FSt - F buoyant (3)

Figure 1

Ball drop in the fluid is accelerated only at the very beginning of the motion, then became to
be uniform because friction force increases with increasing of velocity and together with the
Archimedes buoyancy force balances the force of gravity W. From that moment the ball will
move uniformly with terminal speed and equation (3) can be written as:
W - FSt - Fbuoyant = 0 (4)
Archimedes force is equal to the weight of the liquid in the volume of the ball (F buoyant = W1).
Considering this we can write:
W - W1 = FSt (5)
4 3 4 3
where W =mg= π r dg and W 1=m1 g= π r d 1 g
3 3
are the weight of ball and discharged liquid respectively. d - density of the ball, d 1 - density of
the liquid. Equation may be rewritten in form:
4 3
π r g ( d−d 1 )=6 πηrυ (6)
3
or
2
2(d−d 1 )g r
η= (7)
9
By using equation (7) may be calculated the viscosity of the sample liquid.
As the ball drops may be used an aqueous solution of copper sulfate, which takes shape with
lower surface if it drops in another liquid, i.e. spherical shape. The radius of the drop is
determined indirectly by weighing. To do this, measure the mass M of the "n" drops, then the
mass of a single drop is
M dV 4 3
m= = = πr d
n n 3
and
r=
√ √
3 3m

4 πd
=
3 3M

4 nπd
Thus, by substituting radius of the ball from expression (8) in (7), we can calculate the
(8)

coefficient of viscosity of the liquid.

 Description of Installation
Experimental setup is shown in Figure 2. As a sample
liquid can be taken vegetable oil. Oil is poured into the
cylindrical vessel C with deposited on it and ring marks a
and b. A solution of copper sulfate is poured into a
dropping glass C1 located above the container C. From the
pipette D solution drop falls in a container C, and by
stopwatch we measures time of falling of the drop between
the marks a and b. Knowing the time, are calculated the
terminal speed of the falling drop.
Figure 2
The progress of work

1. Immersing a drop of copper sulfate solution in a vessel using a D pipette, followed it

movement. At the moment of achieving of drop the mark (a) start the stopwatch and stop it at
the moment of drop reaching the mark (b). Knowing the time of fall t between the marks (a)
and (b) and the distance l between them, calculate the speed of drop fall.
2. Calculate the radius of the drop. For this measure mass m2 of carefully dried cup on a balance.
Placing cup under the dropper, drip into it 50-60 drops of the solution and measure the mass
of the glass with solution m3. Thus mass of solution will be equal to the M = m3 - m2.
Knowing the number of solution n and their M mass, calculate the drop radius r by the
formula (8).
3. Based on the data v and r according to formula (7) calculate the value  (values of d and d1
are available in the laboratory).
4. Repeat experience 3 times, calculate absolute and relative experimental error.

Data Table
№ l, m v,m/s t, s m3, kg m2, kg m1, kg m, kg , Pa∙s
1
2
3

Questions for laboratory work.

Mechanics of fluids, equation of continuity and Bernoulli's equation. Ideal and viscous
liquids. Laminar and turbulent fluid flow. The Reynolds number. Stokes formula.

LABORATORY № 12
DETERMINATION OF THE COEFFICIENT OF INTERNAL FRICTION OF A
LIQUID ACCORDING TO THE POISEUILLE LAW
Objective: Acquaintance with the main regularities of the motion of viscous liquids and the
determination of the coefficient of internal friction by an experimental method.
Accessories: Viscometer, stopwatch, pycnometer, distilled water, test liquid, scales and weights.
Works theory
One of the methods for determining the coefficient of internal friction of a liquid is based
on the Poiseuille law. According to this law, the volume of liquid laminarly flowing through the
capillary tube is determined by the formula:
πr 4 Pt
V= (1)
8 ηl
Here r is the radius of the tube, l its length, P is the pressure exerted on the moving fluid, and V
is the volume of liquid flowing out of the tube during time t. From here
8 lV
t=η 4
πr P
If we take the same volumes of two different liquids, then depending on the coefficient of
internal friction, the time of the outflow of these liquids through the same tube will be different,
namely:

8 lV 8 lV
t 1=η1 t 2=η2
πr 4 P1 and πr 4 P2
From the last two relations we have:
t 1 η 1 P2
= (2)
t 2 η 2 P1
If the heights of the columns of liquids are the same and equal to h, then the pressures and are
respectively equal to:

P1 =ρ1 gh and P2 =ρ2 gh

Where ρ1 and ρ2 density of liquids. Substituting P1 and P2 values of into the equation (2), we
obtain t 1 η 1 ρ2
=
t 2 η 2 ρ1
From here
ρ1 t 1 (3)
η1 =η2
ρ2 t 2
Обычно в качества эталонной жидкости берут
дистиллированную воду. Поэтому в
уравнении (3) ρ2 - плотность воды, t 2 - время её истечения, η2 -
коэффициент внутреннего трения воды.
To determine the coefficient of internal friction, the Ostwald
viscometer is used. This viscometer is a U - shaped tube DABC (Fig.
1). The tube has spherical extensions A and B, connected to each
other by a capillary L. The expansion volume A is usually 3-5 cm3.
The spherical expansion B is provided with two marks a and b, which allow one
to Fig. 1 determine the times of the expiration of equal volumes of liquids. To
maintain a constant temperature during the experiment, the viscometer is
placed in a thermostat.

Procedure and analysis

1. Thoroughly wash the viscometer with the liquid to be tested, then fill the extensions
A and B with this liquid so that its level is slightly higher than the mark a.
2. By opening the hole D, allow the liquid to flow out of the expansion B. At the
moment of passing the liquid through the mark a turn on the stopwatch, and at the
moment of passing the mark b, stop the stopwatch. Note down the stopwatch data.
Experience repeating 3-5 times.
3. Repeat the same experiment with water. Determine the time of the outflow of water.
 4. Determine the density of water and liquid. Knowing the coefficient of internal
friction of water, according to formula (3), calculate the coefficient of internal
friction of the liquid being studied.
5. Repeat the experiment 3-4 times and calculate the absolute and relative errors of the
experiment according to the results obtained.

Measurement table.
№ t1, s t2,s η2 , Pa⋅s ρ1 , kg / m 3 ρ2 ,kg / m 3 η1 , Pa⋅s

1.
2.
3.

Questions to the lab. Mechanics of liquids. Ideal and viscous liquids. Laminar and turbulent
flow of liquids. Reynolds number. The Poiseuille formula.

LABORATORY № 13
DETERMINATION OF THE SURFACE TENSION OF A LIQUID BY DROP METHOD
Objective: Studying the phenomenon of surface tension in liquids and the experimental
determination of the surface tension.
Accessories: Drip, analytical balances and weights, a glass, a micrometer or caliper.
Works theory
The force of the interaction between the molecules of the fluid decreases very rapidly with
increasing distance between them. Therefore, each molecule interacts with the molecules which
are located at some distances from it. The sphere within which the molecule can interact if it is
situated in the center of it is called the sphere of molecular action.
Consider a molecule A, located inside the liquid so that the sphere of its molecular action is
entirely inside the liquid (Figure 1). The forces acting on this
molecule from other molecules, in average balance each other.
Therefore, the role of forces of the molecular action under these
conditions is to regulate the distance between the molecules.
The conditions of molecules located in the surface layer of the
liquid are completely different . Part of the sphere of molecular
action is out of the liquid. Since the liquid density much greater
Fig. 1 density of
the liquid vapor, the concentration of molecules in the part of
the
sphere, located above the liquid surface, much less than the
concentration of molecules in the rest of the sphere. As a result, from the liquid on the molecule
B, and also on all the molecules which are located inside the liquid at a distance equal to the
radius of the molecular action from the liquid surface the forces directed inside the liquid are
acting which are many times greater than the forces exerted by the molecules of vaporized
liquid . Thus, the molecules on a surface layer exert on the whole liquid the pressure, called
molecular pressure. Each molecule in the transition from the lower layers to the surface layer
must perform the work against the pressure of molecular forces. This leads to an increase in its
potential energy. Therefore, the potential energy of the molecules of the surface layer is greater
than the energy of the molecules of the underlying layers.
 The free energy of the molecules of the surface layer is also greater than the energy of other
molecules, but the average kinetic energy of all the molecules of the liquid are the same (free
energy is equal to the difference between potential and kinetic energy).
It is known that the equilibrium position corresponds to the minimum of the potential
energy. The liquid left to itself, will take the form of a minimal surface, that is, surface cutting
will take the form of a ball. This phenomenon is called surface tension. The surface tension of
liquids characterized by the coefficient of surface tension. Surface tension factor is the free
energy per unit surface of the liquid or surface tension force per unit length of any line drawn on
the surface of the liquid, i.e.
ΔΕ F
σ= =
ΔS l

There are several methods for measuring the surface tension. One
method is the drop one.
The liquid flows from the narrow tube drop by drop, which before the
separation of the capillary have the form shown in Figure 2.
Assume that the outer radius of the tube is equal to R. The drop can
break away from the tube only under certain conditions. There are two
oppositely directed forces acting at a drop. The force of gravity and the
force that holds drop - the force of surface tension. Drop off from the tubes
when gravitational force becomes equal to the force of surface tension, ie,
p=2 πxσ here p-drop weight (p = mg) σ - coefficient, r - neck radius AB. Fig. 2
Experience shows that the glass tubes with a wall thickness of 1 mm neck radius r and the outer
radius of the tube R are related by: r=0 , 62 R
Thus, we obtain:
mg=2 πrσ =0 , 62⋅2 πRσ
Hence, obtain the expression
mg
σ=
0 ,62⋅2 πR (1)
where m - the mass of a single drop. Thus, for calculation it is the need to know the
magnitude of the inner or outer radius of the tube and one drop weight.

Procedure and analysis

1. Determine the mass m1 of thoroughly cleaned and dried cup using an analytical balance.
2. Set the tap K (Figure 2) in a position to be able to count the number of falling liquid droplets
from a tube . Putting a glass under the pipe, drip into it n=90−100 liquid droplets.
3. Measure the mass m 2 of the cup with liquid.
4. Determine by the formula m 2 −m 1 the mass of the liquid in the cup.
m −m1
m= 2
5. Determine the mass of a single drop by formula n
6. Measure the outer radius of the tube using a micrometer or caliper.
7. According to data obtained by the formula (1) calculate the value σ .
8. Changing the number of drops each time, repeat the experiment 3-5 times. Find the average
value σ . Calculate the absolute and relative error experience.

Measurement table.
№ m1, kг m2 , kг m3, kг m, kг R, m σ ,Н/m
1.
2.
3.
 Questions to the lab. Surface tension. Wetting phenomenon. Capillarity.

LABORATORY № 14
DETERMINATION OF THE AVERAGE FREE PATH LENGTH AND THE
EFFECTIVE DIAMETER OF AIR MOLECULES
Objective: The experimentally study of methods for determining the average free path length and
the effective diameter of air molecules.
Accessories: capillar and a glass jar with a tap, a stopwatch, beaker, ruler.
Works theory
Gas molecules, being in thermal motion continuously collide with each other. During the time
between two successive collisions gas molecule passes some way, which is called the mean free
path. The mean free path is the value determined by the expression:
(1)
1
λ̄=
√2 πσ 2 n
where σ - the effective diameter of the molecule, n - the concentration. The value σ can be
found using Poiseuille's law, according to which the volume of liquid, laminar flowed over time
t through a capillary tube radius and length l , defined by the formula
πr 4 Pt
V= (2)
8 ηl
where P - the pressure exerted on a moving fluid, η - viscosity of liquid. On the other hand
according to the molecular-kinetic theory the internal friction coefficient is
1
η= ρ ῡ λ̄ (3)
3
where ϑ̄ - the average speed of the thermal motion of the molecules, and ρ - the gas density
is determined by the formula
pM
ρ= (4)
RT
Substituting in the formula (3), we have:
1 PM
η= ῡ λ̄ (5)
3 RT
where R - the universal gas constant, T - the absolute temperature, M - the molar mass of
the gas.
Taking into account η in the formula (2) we get:
1 PM (6)
η= ῡ λ̄
3 RT
where ῡ=
√ 8 RT
πM
(7)

Substituting this expression in (6) and determine the average free path length
 √
4
3 πr tΔP π RT
λ̄=
16 PVl 2M (8)

Thus, by calculating λ̄ with the equation (8), from the formula (1) the numerical value for
the effective diameter of the molecule can be found
1
σ= (9)
√ √2 πn λ̄
The concentration of gas molecules n can be determined as follows. According to the basic
equation MKT for normal conditions,
P0 =n 0 kT 0 and for an arbitrary state P=nkT . From
these two relations

PT 0
n=n0
P0 T (10)
25
T =273 K and P0 =1 , 013⋅105 Па
where n 0=2 , 3⋅10 м - the number of Loschmidt, 0
−3

. Substituting (10) into (9), the effective diameter

σ=
√ P0 T (11)
√ √2 πn 0 PT 0 λ̄
Installation, procedure and analysis.
To perform the work the installation shown in Figure 1 is used

Fig. 1
1. Fill the container В with water and measure the height h1 of the
liquid column.
2. Open the tap K and simultaneously start the stopwatch. Measure the flow time t when
filling the cup with 200 - 250 см3 of water,
3. Measure the volume of leaked water (it is equal to the volume of air passing through
the capillary A.)
4. Measure the height of the water column h2 after the water outflow, and using the
following formula calculate the pressure difference h +h
ΔP= 1 2 ρg
2
 5. Knowing the value of atmospheric pressure P and temperature T calculate by the
formulas (8) and (11) numerical values λ̄ , and σ respectively.
6. According to the results calculate absolute and relative experimental error.

Measurement table.

№ P, T, K t, s h1, h2, m V, m3 ΔP ,Pa λ̄ , σ ,m

Pa m m
1.
2.
3.
Questions to the lab. The main equation of MKT. The average free path of the molecules.
Poiseuille’s formula.
Laboratory Work # 15
Determination of the Boltzmann constant
Work Objective: Studying the ideal gas law, the experimental determination of
the Boltzmann constant.
Accessories: Glass container of 5-10 liters, a medical syringe, manometer,
indoor thermometer, ether.
Short theoretical information
The state of gas is characterized by state parameters: pressure P, volume V, and
temperature T. The equation relating the parameters of state of an ideal gas is
called the equation of state or Chaperon - Mendeleev equation:
m
PV = RT
M (1)
where m - the mass of the gas, M - molar mass of the gas, and R - universal gas
constant. Universal gas constant shows how much work will be done for isobaric
expansion of 1 mole of gas when heating it to 1 K.
The ideal the gas, which neglected the forces of intermolecular interaction and
its own volume of molecules. Ideal gas molecules behave as a completely elastic
balls is therefore considered that the molecules possess only ideal gas kinetic
energy value for each molecule of which is:
The gas of neglected forces of intermolecular interaction and own volume of
molecules is called the ideal gas. Ideal gas molecules behave as a completely
elastic balls. Therefore considered that the molecules of ideal gas possess only
kinetic energy which value for each molecule is:

(2)
where i - number of degrees of freedom of the molecule (the number of
independent coordinates defining the position of molecules in space), k -
Boltzmann constant, associated with the universal gas constant by the following
relation:
R
k=
NA (3)
NA - Avogadro number, indicates how many molecules contained in one mole of
any gas. The physical meaning of the Boltzmann constant is that constant k shows
how much work is done by each molecule in the process of isobaric expansion gas
for increasing its temperature by 1K.
Substitute the Boltzmann constant in the equation (1) and obtain
m
PV = N A kT
M
mN A
n=
Or if we note that MV - is a concentration of atoms we get:
p=nkT (4)
From equation (4) it follows that the ideal gas pressure at a given temperature is
determined by the number of molecules per unit volume (concentration of
molecules), and does not depend on the type of gas. If there is a mixture of gases
such as air in this job (a mixture of mainly oxygen and nitrogen) the pressure is
equal to:
(5)
n n ,
wherein 1 , 2 etc. represent the concentration of molecules of the first, second, etc.
gas kinds of.
Expression (5) can be represented as:
P=n1 kT +n2 kT +. .. (6)
wheren1 kT - is the pressure in the vessel if there were only first kind molecules,
n2 kT - is the pressure that would be in the presence only the second kind of
molecules in the vessel, etc.
The pressure due to molecules of any one kind, provided that they only one are
present in the vessel in quantities in which they are contained in the mixture is
called the partial pressure of the corresponding component of the gas mixture.
By introducing partial pressure p1 , p2 . .. on the base (6) equation can be written
p= p 1 + p2 +. .. . (7)
Equation (7) expresses Dalton's law, which states that the pressure of an ideal
gas mixture is the sum of the partial pressures of gases that make up the mixture.

Description of Installation

Installation for determining the Boltzmann constant

(Figure 1) consists of a vessel with a capacity of 5-10
liters and connected to it water manometer. Into the
vessel closing cork a tube with tap is inserted for
communication with the atmosphere and the needle for
introduction into a vessel of a volatile liquid. If enter into
the vessel some amount of easily evaporating liquid mass
of m, it will evaporate quickly and creates additional
pressure P in the vessel, and the vapor pressure will be balanced out by the
pressure of liquid column in manometer.
Apply to the vapors of volatile liquid Chaperon - Mendeleev equation (1).

(8)
where P- the partial vapor pressure created in the vessel by vapor of entered
liquid, V - the volume of the vessel, - mass and M - molar mass of a
volatile liquid, entered into the vessel. dliq- density of volatile liquid, d- density of
liquid used in manometer. From (8) for the Boltzmann constant obtain:

(9)
The experimental parts of work are: to determine the volume of volatile liquid
taken for the experiment, to determine of difference of water level in manometer
and to measure temperature in the room T (in absolute temperature scale).
The progress of work
1. Open the tap K of the communication of the vessel with atmosphere for setting
liquid in the manometer at same level.
2. Measure the temperature T at the room.
3. Close the tap K.
4. Fill the syringe and enter into the vessel of volatile liquid. Syringe leave
inserted into the needle in vessel cork, otherwise vessel will be communicated
with atmosphere.
5. After 5-10 minutes, write down the difference between the water level in the
manometer.
6. According to the formula (9), calculate the Boltzmann constant.
7. According to the results calculate absolute and relative experimental error.

№ dliq, Vliq, M, d, V, h, m T, k,
kg/m3 m3 kg/mol kg/m3 m3 K J/K

1.

2.
3.

Questions for laboratory work.

The basic equation of kinetic theory of gas. The ideal gas laws. The equation of
state for an ideal gas (Mendeleyev - Clapeyron equation). Universal gas constant.
Boltzmann's constant.
Laboratory Work # 16
Determination of resistivity according to Ohm's law.
Work Objective: Determination of specific resistance of conductor of knowing its geometric
dimensions.
Accessories: Ammeter, voltmeter, rheostat, studied conductors of different diameters,
micrometer, connecting wires, DC supply.

Short theoretical information

The theory.
Electric current - is orderly movement of electric charges. In metals, electrical current is
created by the directional movement of free electrons and current described by the expression I
= env̄A.
−19
Here e=1 , 6⋅10 C the electric charge of the electron, the n - concentration, v̄- the average
velocity of ordered motion of electrons, the A- cross-sectional area of the conductor.
According to the theory of Lorentz - Drude free electrons in metals behave as a monatomic
gas molecule.
Calculations show that the density of electric current, which occurs under the influence of an
external electric field E is determined by the expression.
ne 2 λ̄
j= E=σE
2 m ῡ
where λ̄ - average free path of electrons, n - concentration of free electrons, m - its mass, σ -
electrical conductivity of the conductor. The inverse of conductivity is called resistivity
1
ρ=
σ
1
j=σE= E
Equation is an expression of Ohm's law in differential form. ρ

I U I U U
j= E= = ❑I=
Taking into account A and l this equation are equal: A ρl ⇒ R
This expression is - integral form of Ohm's Law for subcircuit. Here l- the length of the
conductor, U- the voltage at the ends of the conductor, R - conductor resistance, which is equal
to
l
R=ρ
S (1)

Installation Description

There are several methods to measure the specific resistivity. In this

work, the resistance is determined on the basis of Ohm's law for
subcircuit. Installation diagram is shown in Figure 1, where the
resistance voltmeter should be much greater than the resistance of the
tested conductor.
For current I, passing through the ammeter:
U U
I =I x + I V = +
Rx RV
where
R x - the tested resistance, RV - voltmeter's resistance. If we consider that the RV >> R x
 U U
I= and R x= (2)
Rx I

Knowing the length l and cross-sectional area A of the conductor, we obtain the resistivity:
R x ∙ A π d2 ∙U
ρ= = (3)
l 4 Il

where A = d2/4 and d is the cross-sectional diameter of the conductor.

Progress.

1. Measure the length of the conductor and its diameter at three points.
2. Assemble the circuit as shown in Figure 1.
3. By changing the position of the rheostat's slider record readings of voltmeter and ammeter.
4. Use equations (2) and (3) to calculate the resistance and the resistivity of conductor.
5. According to the results of measurements calculate the absolute and relative uncertainties.

Data Table

№ 1- conductor
U, V I, A R, d, m A, m2 ρ,
ohm ohm∙m
1
2
3
2- conductor
1
2
3

Questions for laboratory work. Electric current. Current. The current density. The electrical
resistance, resistivity, conductivity. Explanation of the electrical conductivity of metals on the
basis of classical electron theory.

Laboratory Work # 17
Determination of the thermal coefficient of metals resistance
Work Objective: Study of depending of metals resistance on the temperature. Experimental
determination of the thermal coefficient of metals resistance.
Accessories: Thermostat, metal sample, ohmmeter, thermometer.
Short theoretical information

Electric current in metals is a directed motion of electrons. Under the influence of an external
electric field, they move against the electric field lines. At the same time participating in a
chaotic and directed of motion, the electrons collide with the lattice ions. Between two
consecutive collisions (the mean free path equal ❑) electrons moving accelerated under an
electric field and at the time of the collision have a kinetic energy
2
mu
W=
2
 If we apply the laws of conservation of energy and momentum to the movement of electrons,
we can see that during the collision energy given to ion, is a small fraction of the total energy of
the electron.
In an inelastic collision, this ratio:
Wi m
= ,
W M +m
and in elastic collision:
W i 4 Mm
= ,
W ¿¿
where m and M the mass of electron and ion respectively.
In both cases, this ratio is about 10 -4 and the energy loss goes to the heating of the metal and
as a result increasing its resistance.
Let us calculate the energy released in as heat, based on classical electron theory. Maximum
speed acquired at the end of the electron free path:
F eE ❑
umax =a= = (1)
m mv
where v - mean square thermal velocity,  - time between two collisions.
If the electron density n is the number of collisions per unit time Z , the energy released per
unit time in a unit volume of the conductor will be equal to:
2
max

( )
me u m e eE { λ̄ 2

ῡ W =n z̄ E k =n z̄ =n z̄ ¿
Taking into account that z̄= 2 2 m e ῡ
λ̄
we have ne 2 λ̄ 2
(2) W= E
2 m ῡ

The electrical conductivity of metals is

ne 2 λ̄
σ= (3)
2 m ῡ
Thus by combining (2) and (3) we get: 1 (4)
W =σE2 = E2
ρ
This is the Joule -Lents law in differential form
The high concentration (n ~ 1028 m-3) and high mobility of free electrons in metals is the cause
of their good electrical and thermal conductivity. The thermal conductivity of metals associated
with the presence of free electrons, which behave as monatomic molecules. In this case, for the
thermal conductivity can be borrowed the expression of the kinetic theory of gases
1
χ = ρ ῡ λ̄ c v
The specific heat capacity of a monatomic 3 gas is
CV 3 R 3 k
cV = = =
M 2M 2m
Substituting this expression in the previous we have
1
χ = nk v ❑ (5)
2
here k - Boltzmann constant. Combining (3) and (5) we get the Wiedemann - Franz law.

(6)
As can be seen from this formula, the ratio of the thermal conductivity to the electrical
conductivity is constant for all metals and depends only on the temperature of metals. From (6)
can be obtained that
 ρ=ρo ( 1+ αt )∨ρ=ρo αT (7)
These relationships also hold true for the resistance of metals:
R=R o ( 1+ αt )∨R=Ro αT (8)
o
where ρo and Ro are resistivity and resistance at temperature 0 C respectively; α- thermal
coefficient of resistance and it is equal to the relative change in the resistance of a conductor
when temperature changes by 1oC; t-temperature in degree of Celsius and T - temperature in
Kelvin.

Installation Description
Installation diagram is shown in Figure 1. The tested conductor is
a wire wound around a bobbin and placed in a vessel filled with
industrial oil. This prevents the sample from corrosion and
mechanical damage, while providing effective heat exchange. It
should be borne in mind that the sample takes the temperature of the
medium due to the heat transfer with finite speed, not instantaneous
with some delay. Therefore, the measurement should be carried out
at appropriate intervals.

Work progress

1. Using the thermostat and the measuring device B7-16 make

measurements of sample resistance at every 5 0C starting from the room
temperature. According to obtained data plot the graph.
2. According to the angle of graphics inclination calculate the
thermal resistance coefficient α by the formula:
tgφ
α φ=
Ro

3. Calculate α also by formula (8). Compare the obtained results.

4. Calculate the measurement uncertainty

Data Table

№ tº C Rt Ом tgϕ αК
−1
α ϕ К −1
1.
2.
3.
4.
5.
6.
Questions for laboratory work. The temperature dependence of the resistance of metals.
Superconductivity.

LABORATORY № 18
DETERMINATION OF ELECTRIC CAPACITY OF THE CAPACITOR BY AC
BRIDGE
Objective: Introduction to the working principle of alternating current bridge , the determination
of the capacity of the capacitor by AC bridge.
Accessories: Capacitors with known and unknown capacities, slidewire, telephone, an
oscilloscope, an alternator, a sound generator.
Works theory
Electrical capacitance C of a secluded conductor (conductor which is remote from the other
q
C=
conductors) is defined as the ratio of its charge to its potential ϕ
Electrical capacitance of the conductor increases with coming nearer of surrounding bodies
to it. This is because under the influence of an electric field of a charged conductor in
surrounding bodies electrical charges are induced (free in conductors and connected in
insulators). This in turn leads to some reduction potential difference. In this case we can speak of
mutual capacitance. Devices having mutual capacitance and capable of accumulating an electric
charge are called capacitors. The electrical capacitance is determined by the formula
q
C=
ϕ 1−ϕ 2
where q - the electrical charge of one of capacitor plates ( ϕ 1 −ϕ 2 ) - a potential difference
between them. There are different types of capacitors: a cylindrical, spherical, flat. Capacitance
depends on the geometrical shape and sizes, the dielectric constant of the material between the
capacitor plates. For example the capacity of the most common parallel-plate capacitor is given
by
q εε S
C= = 0
ϕ 1−ϕ 2 d

where ε - the dielectric constant of the medium,

ε 0 - electric constant, S - area of one
electrode, d - the distance between the plates.
Besides electrical capacitance, each capacitor is characterized by a maximum voltage m ,
U
which can be between the plates - the breakdown voltage. At voltages higher breakdown the
dielectric between the electrodes breaks and the capacitor fails.
AC bridge can be used to measure the capacitance (Figure 1).
The principle of this method lies in the fact that the unknown capacitance is included in one
of the arms of the bridge, then by selection of known capacitances
and resistances balance of the bridge is achieved.
Conditions for balance of four arms bridge is:

Ζ1 Ζ 4 −Ζ 2 Ζ 3 =0 (1)
where Ζ1 - resistance of bridge arms. Usually for four arms ac bridge
two Fig. 1 arms have an active resistance. In this case Ζ1 =R1 , and Ζ 2=R 2 .
To create a balance (equilibrium) to one of the arms of the bridge the reactive
(capacitive) resistance
Z 3=R c should be connected.
1
Rc =
Given that 2 πν c

where ν - AC frequency and using the condition (1):

R1 Rc x =R2 Rc
we can write l l
1 1
ρ 1⋅ =ρ 2⋅
S 2 π vC X S 2 π vC

Hence we obtain for the unknown capacitance

C x l1 l
= C x =C 1
C l 2 или l2 (2)
Procedure and analysis
1. Assemble the circuit as shown in Figure 1
2. Changing the position of the slider find the point M on the slidewire, in which the sound of the
phone would be minimal. Write the numerical values for this case MA=l 1 and MB=l 2 .
3. Calculate the unknown capacitance by the formula (2) (select capacitors with known
capacitances ). Perform measurements for serial and parallel connections.
4. Carry out the measurements at least 3 times for different known capacitances.
5. Calculate the measurement errors.

Measurement table.

1st sample 2nd sample

l1 , m l2 , m C , F С х , F l1 , m l2 , m C , F С х , F
1
2
3

Questions to the lab. The electrical capacitance of a solitary conductor. Various types of
capacitors, its electric capacity. Series and parallel connection of capacitors.

LABORATORY № 19
DETERMINATION OF ELECTRIC CAPACITANCE OF A CAPACITOR BY THE
DISCHARGE METHOD
Objective: Study of the capacitor discharge process, the determination of capacitance of a
condenser by the discharge method.
Accessories: Capacitor with an unknown capacitance, resistors with known and unknown
resistances, switch, multimeter, power supply, a stopwatch.
Works theory
When the discharge of the capacitor through a permanent resistor during the time dt the
capacitor charge is changed by a value

dq=−Idt (1)
On the other hand
U
I=
R (2)

q
U=
C (3)
Using (2) and (3) in (1) we have:
q
dq=− dt
CR (4)
where I - current, U - voltage on the capacitor R - resistance of resistor, С - capacitance of
capacitor. A solution of equation (4) is an expression
t
−
RC
q=q 0 е (5)

Deviding (5) by С :
t
−
RC
U =U 0 e (6)
Devide (6) by we obtain:
t
−
RC
I =I 0 e (7)

Time τ =RC is called relaxation time.

In practice, the graph of the logarithm of voltage versus time is more
comfortable for the determination of the capacitance . Taking a
logarithm of the expression (6), we obtain: Fig. 1
1
ln U =ln U 0 − ⋅t
RC (8)

This relationship is shown on Figure 1

Now we find the tangent of the slope of a straight line:

ln U 1 −ln U 2
tg α =
t 2−t 1 (9)

On the other side the modulus of the tangent of the slope from the formula (8) is:
1
tg α =
RC (10)

1
C=
And Rtg α (11)

Installation diagram is shown on Figure 2. To limit the value of the current the capacitor
charging process is carried out via a resistor. A digital multimeter is using to measure the current
and voltage (Figure 3). You can also measure the resistance with it. The following are the
meanings of symbols on the multimeter. DC - direct current, AC - alternating current,
A - current, V – voltage, Ω - resistance, m - milli, µ - micro. The numbers
show the limit measurements in this mode.
 Fig. 2

Fig. 3

Procedure and analysis

R
1. Charge the capacitor from the source ε through the resistance x in 10-15 seconds.
2. Use switch Ç to discharge the capacitor through the resistance R , and every 5s measure its
voltage.
3. Plot the graph of logarithmic dependence of voltage versus time.
4. Calculate the capacitance of the capacitor using this graph.
5. Calculate the measurement uncertainty (measured voltage is in the mode of 2000 mV, the
error is 4 mV, relative error when measuring the resistance is equal to 3%).

Measurement table.

t, s

U, mV

ln U

Questions to the lab. Electrical capacitance. Various types of capacitors. Series and parallel
connection of capacitors. Changing the charge and voltage on the capacitor during its charging
and discharging.

LABORATORY № 21
STUDYING OF SEMICONDUCTOR RESISTANCE DEPENDING ON THE
TEMPERATURE AND DETERMINATION OF THE ACTIVATION ENERGY
Objective: Study of the mechanism of electrical conductivity and resistance depending on
temperature semiconductors. Determination of the activation energy.
Accessories: The semiconductor sample, thermostat, thermometer, universal voltmeter V 7−16
Works theory
Substances by their electrical conductivity are divided into three groups:
−7 -5
• Metals with a resistivity 10 -10 ohm-meters
12 17
• Dielectrics, the resistivity of which is 10 -10 ohm-meters
• Semiconductors, electrical conductivity of which greater than insulators and less than that
-5 10
of metals. Their resistivity is in the range of 10 -10 ohm-meters
Such classification of substances is not associated with these formal features, but explained
by the emergence of new energy levels - areas due to the socialization of valence electrons of
interacting atoms and molecules contained in them (Figure 1).
It is known that an electric current occurs at an orderly motion of free electrons. To do this,
the valence electrons from the "valence band" jumping into "conduction band" are turning to free
electrons. The valence band and the conduction band are separated from each other by
"forbidden zone" .
1. In metals, the valence band is partially or completely filled with electrons overlaps the
conduction band (Figure 2)
2. In dielectrics, the band gap is so large (on the order of a few electron volts), that neither
heat nor the energy acquired by electrons in an electric field, is not sufficient to transmit them
into a free zone (conduction band Figure 3)

forbidden

energy levels
zone

atom
energy zones

of
Fig. 1

dielectric semiconductor

Fig. 3
conduction
zone conduction
zone
forbidden
zone
valence
zone
valence
zone
Fig. 2

3. In semiconductors band gap smaller than that of dielectrics. In this case, the electrons under
the external influence (electrical, thermal, optical, etc.) pass from the valence zone to the
conduction zone. This can happen if there is vacancy in the conduction band. The energy
required to transfer an electron from the valence zone to the conduction zone is called the
activation energy Еа .
The conductivity of the semiconductor is strongly dependent on temperature. With increasing the
temperature, the valence electrons acquiring energy equal to the activation energy, are leaving
the atom and become free. Due to the fact that the activation energy does not have such a greater
numerical value, even at room temperature, a sufficient number of electrons can be in the
conduction zone. In this case the vacancies formed in the valence band, behave as positive
charges and are called the holes.
The holes, moving opposite with respect to the electrons involved in the creation of the current in
a semiconductor. Thus the own conductivity of semiconductors consists of electron and hole
conduction.

σ =en μn +ep μ p
(1)
 Here, n and p, respectively, the concentration of electrons and holes,
μn and μ p their
mobilities.
Mobility is numerically equal to the velocity acquired by the charge carriers in the electric
field of unit strength.
ϑ
μ=
Е
In semiconductors, the conduction band electron concentration obeys the exponential law
Ea
2 kT
−
n=n 0 e (2)
n Е
where 0 - coefficient of proportionality, weakly temperature-dependent, а - activation
energy – the energy equal to the band gap. The energy required to create a free charge carrier is
Еа
2 (two carriers - electron - hole pair, are formed at an energy expenditure of Еа). Therefore,
the temperature dependence of the own conduction is:

Еа
−
2KT
σ =σ 0 е
(3)

The temperature dependence of the resistance of conductors can be written as:

E
a
2 KT
R=R 0 e (4)

Taking the logarithm of expression (4), we obtain:

Ea
ln R=ln R0 +
2 KT (5)

In practice it is convenient to calculate the activation energy from the relation:

ln R=f ( )
10 3
T (6)
Figure 4. shows graph of this relationship.

For the tangent of the slope angle direct obtain:

R
ln 2
ln R2 −ln R1 R1
tg α = =
103 10 3 103 103
− −
T2 T1 T2 T1 (7)
Using the expression (5), to obtain a tangent: Fig. 4
Ea
tg α = ⋅10−3
2K (8)
 Given this expression, we can calculate the numerical value of the activation energy
E a=2 K⋅10 3 tg α or E a=0 ,17 tg α (eV)
Thus, determination of the activation energy is reduced to the determination of the angle
coefficient from the plot of resistance versus temperature. The device scheme for determining
the activation energy is shown in Figure 5.
Thermometer Thermostat

Sample Ohmmeter
Fig. 5

Procedure and analysis

1. Measure the resistance of a semiconductor placed in an thermostat using an ohmmeter at
room temperature. By turning on a thermostat measure the sample resistance every 100C,
recording them in the table.
2. Performing 8-10 measurements, and draw the graph on the received data ,and calculate
the tanget of slope angle using the formula 7.
3. Use the result obtained to calculate the activation energy according to the formula 9 .
4. Calculate the absolute and relative measurement error.

Measurement table.

rn , M
R , Om
103 / T
LnR

Questions to the lab. Zone theory of solids. Semiconductors. Semiconductors of n and p types.
Own and impurity conductivity.

LABORATORY № 22
DETERMINATION OF THE HORIZONTAL COMPONENT OF THE EARTH'S
MAGNETIC INTENSITY
Objective: Acquaintance with elements of terrestrial magnetism, determination of the horizontal
component of the earth's magnetic field strength.
Accessories: Tangent - galvanometer, constant current source, ammeter, rheostat.
Works theory
The earth is a huge ball magnet whose poles lie near geographic poles: near the northern
geographic pole is located the southern magnetic S, and near the southern geographic pole - the
northern magnetic pole N (Fig. 1). At any point on the surface of the earth and in the surrounding
space, the effect of the magnetic field is detected. The direction of the Earth's magnetic field
lines can be set with a magnetic needle. At the equator, the magnetic field is directed
horizontally, and at the magnetic poles it is vertical, at other points it is directed at some angle to
the earth's surface. This angle is called the declination angle and is denoted by a letter ϕ .
 The projection of magnetic field induction onto the horizontal plane is called the horizontal
component of the Earth's magnetic field (B). The direction of this component is taken as the
direction of the magnetic meridian. The vertical plane passing through such a meridian is called
the plane of the magnetic meridian. The angle between the geographic and magnetic meridians is
called magnetic declination (ϕ ).
Lines of the Earth's magnetic field, generally speaking, are not parallel to the Earth's surface
(Fig. 1). This means that the magnetic induction of the Earth's field does not lie in the plane of
the horizon of the given place, but forms an angle with this plane. This angle is called the
magnetic inclination and is denoted by a letter β . Earth magnetism is characterized mainly by
three quantities: the horizontal component B11 , the angle of declination ϕ and the angle of
inclination β .
Knowing the angle of declination and the magnitude of the horizontal component of the
magnetic field strength of the Earth in some place, it is possible to determine the magnitude and
direction of the vector of magnetic induction corresponding to that place.
In this paper, the horizontal component of the Earth's magnetic field intensity H 11 is
calculated. For this, a connection is used between the vector of magnetic induction and the
intensity of the earth's magnetic field.
→ →
B =μμ 0 H
−7
where μ0 =4 π⋅10 Hn/m the magnetic constant, μ is the magnetic permeability of the
medium.
To determine the horizontal component of the induction of the Earth's magnetic field, the
tangent-galvanometer (TG) is used (Fig. 2). The TG is a coil of radius R with a certain number
of turns of wire n located in the vertical plane. A compass is placed in the horizontal plane at the
center of the coil, the arrow of which can rotate about the vertical axis under the influence of the
horizontal component of the induction of the Earth's magnetic field. In the absence of current in
the coil, the magnetic needle is directed along the magnetic meridian of the Earth MM (Fig. 3).
Aligning the plane of the coil with the plane of the magnetic meridian can be achieved by turning
the plane of the turns around the vertical axis. If after that to pass current through the turns, then
the magnetic needle will turn to some angle ϕ (Fig. 3). This is explained by the fact that along
B
with the magnetic field of the Earth B11 , a magnetic field is created by a field 0 created by a
circular current in the center of the turns. According to the Bio-Sawar-Laplace law, the magnetic
induction at the center of the circular current is calculated by the formula:
μ0 μJ⋅n
B0 =
2R (1)
On the other hand, as seen from (Fig. 3).
B0 B0
tg ϕ= ⇒ B 11=
B11 tg ϕ (2)

Fig.1 Fig.2 Fig.3

 Substituting (1) into (2) we obtain
μ0 μJ⋅п
B11 =
2 Rtg ϕ (3)
If we take into account that μ=1 , then for the horizontal component of the magnetic field
intensity of the Earth we have:
J⋅n
H 11=
2 Rtg ϕ (4)
The scheme of the experimental setup is shown in Fig.4. Here E is
the power source, R is the rheostat, A is the ammeter, K is the key, and
G is the tangent is the galvanometer.

Fig. 4
Procedure and analysis
1. Arrange the plane of the turns in the plane of the magnetic meridian. In this case the magnetic
needle is located in the plane of the turns.
2. By closing the key, increase the current through the turns until the magnetic needle turns by 30
to 600 (better results are obtained at angles close to 450)
3. Knowing the radius R and the number of turns n, (usually these values are indicated by the
TG), calculate the numerical value by the formula 4.
4. Repeat the experiment at different values of the current. Calculate the absolute and relative
errors of the experiment.

Measurement table.

№ J ϕ п R H 11
1
2
3
4

Questions to the lab. Magnetic field of a conductor with a current. Intensity and induction of the
magnetic field. The Bio-Savar-Laplace law. The intensity of the magnetic field in the center and
on the axis of the circular current.

Laboratory Work # 23
Determination of the specific charge of an electron by magnetron

Work Objective: Introduction to one of the methods of studying of charged particles motion
in electric and magnetic fields, and determination of specific charge of an electron.
Accessories: Electronic lamp 204 S, three DC sources: 100-150 V for anode circuit, 20-30 V
for solenoid and 1-2 V for cathode circuit, microammeter of DC current and connecting wires.
Short theoretical information

The main characteristics of the charged particle are its charge and mass. The trajectory of a
charged particle in electric and magnetic fields determined by the characteristics of these fields
and the specific charge of the particle. The specific charge of the particles is the ratio of the
charge q of the particle to its mass m (q / m). The specific charge of the SI is measured in C / kg.
Having empirically determined specific charge of the particles, and knowing the amount of its
charge, the mass of the particle can be calculated with high accuracy. It should be noted that the
determination of the specific charge of the unknown particles at one time led to the discovery of
the electron.
One method of determining the specific charge of an electron is the method of magnetron.
The essence of this method is as follows: is known that moving in a magnetic field charged
particle experiences Lorentz force, which is determined by the formula

⃗
F =q ∙ ⃗v × ⃗
B

where - q charge of the particle, v - its velocity, B - magnetic induction. The direction of the
Lorentz force is determined according to the "right hand" rule (Figure 1)
The force acting on a negative charge, is in the opposite
direction. In case where v and B are parallel, the Lorentz force
is zero. And if they are mutually perpendicular, in a uniform
magnetic field, an electron will move in a circular path.
According to the Newton's second law F = ma. Considering
that the a =v2/R we get
2
mv e v
evB= and = (1)
R m BR
Figure 1
where - electric charge and m - mass of the electron.
On practice this condition can be realized in a vacuum tube with a cathode
filament and being coaxial with it metal cylinder, which is the anode. The lamp
is placed inside the solenoid, which magnetic field is directed along the axis of
the anode (Figure 2). Here, A - anode, K - cathode. The nature of the electron
motion inside the lamp depends on the magnetic field induction of solenoid.
Figure 3 shows the possible options trajectories. In the absence of a magnetic
field (B = 0) the electrons emitted from the heated cathode moving in the radial
direction under the influence of an electric field, reach the anode, thereby
creating a current in the anode circuit. In the event of existing of magnetic field
as well as electric field, Lorentz force acts on the electrons, and they are Figure 2
moving along a trajectory close to circular. With increasing magnetic induction
circular orbit radius decreases.
At a certain value of the magnetic field of the solenoid (this value is called the critical B = B
crit) the circular trajectory of the electrons only touches the anode and the current stops. If comes
the moment when B> B crit, the electrons can't reach anode. In the lamp with a very thin
cathode, the radius of the electron trajectory is equal to the half of anode radius when the
conditions of B = Bcrit is satisfied. Electron moving between the cathode and anode being
accelerated by electric field acquires kinetic energy.
2
mv
e U A= (2)
2
where UA - is a anode voltage. Considering that R= rA/2
from (1) and (2) for specific charge we have:
e 8UA
= (3)
m ¿¿

Critical magnetic induction of solenoid is determined by

the expression
Bcrit = μ∙μo∙n∙Jcrit
where μo = 4∙10-7 Hn/m - magnetic constant, μ - Figure 3
magnetic permeability of air, Jcrit - the current in the
solenoid, n = N/l - number of coils of solenoid per unit
length. Taking this into account, for the specific electron
charge we get:
e 8UA
= (4)
m ¿¿

Description of Installation

The experimental setup is shown in Figure 4.

If all the electrons move at the same speed,
the dependence of the anode current on the
magnetic induction would be expressed by
the dashed line (Figure 5a). The real
relationship JA = f(B) is shown in the same
figure, as a solid line. Thus the numerical
value of anode current Jcrit is defined as the
middle point of the segment cd of the
depending of anode current JA on the current
in the solenoid Js (in Figure 5b). Figure 4

Figure 5

The work progress

1. Set a certain value of the anode voltage UA.

2. Turn on solenoid circuit and set current in the circuit to a minimum value.
3. Increase the amperage in the solenoid, measure the corresponding values of anode
current and record they in the table. This requires to make 10-12 measurements at
different solenoid currents.
4. On the basis of obtained data plot a graph of the anode current vs. of the current in the
solenoid JA = f (Js).
5. Continue straight cd section of graph to its intersection with the abscissa axis (Figure 5).
Drop a perpendicular from the midpoint of cd section to abscissa axis. The point of
intersection of the perpendicular corresponds to the value of Jcrit.
e
6. Calculate the values of by formula (4) for three different anode voltages.
m
e
7. Define average value of
m
 Table 1

UA1 = V UA2 = V UA3 = V

J s, A JA, mA J s, A JA, mA J s, A JA, mA

1.

2.

3.

4.

5.

6.

Table 2

UA, V Jcrit, A e e
, C/kg Average , C/kg
m m
1
2
3

Questions for laboratory work.

Ampere force and Lorentz force. The magnetic field of the solenoid. The motion of a charged
particle in a magnetic field.

LABORATORY № 24
DETERMINATION OF THE COEFFICIENT OF SELF – INDUCTION BY JOUBERT
METHOD
Objective: Introduction to one of the methods for determining the inductance and study the
influence of ferromagnetic core to inductance of coil .
Accessories: The study coil, iron core, voltmeter and ampermeter AC, power supply.
Works theory
Occurrence of electromotive force (emf) in a conductor, due to the change of current
flowing through it is called self-induction . It was established experimentally that the emf
occurring in a circuit is directly proportional to the rate of change of current
ΔJ
ε i =− L
Δt
On the other hand, according to Faraday's law of electro-magnetic induction, arose emf
which determined by the rate of change of the magnetic flux Ф:
ε i =−
ΔФ
Δt
According to the Biot-Savart-Laplace law the value of magnetic induction is proportional to
the current, that generates a magnetic field.
The magnetic flux and the current flowing through the loop, related by:
 Ф= LJ (1)
where the coefficient of proportionality L is called inductance. This relationship between
the magnetic flux and the electric current is true if the magnetic permeability of the medium ( μ )
does not depend on the magnetic field intensity (H). It should be noted that the magnetic flux Ф
is also changed according to the shape and geometrical dimensions of the loop. This change is
due to dependence of inductance on the geometric dimensions of loop and of the magnetic
permeability of the medium. When current flows through the long enough solenoid the arising
magnetic field can be considered uniform and the magnetic induction coil in this case is
expressed as:
Β= μ0 μ nJ
Then the magnetic flux through the coil is equal to
Ф=nФ0 =nlBS= μ0 μ⋅n 2 lSJ (2)
−17
where l - the length of the solenoid, S - cross-sectional area, μ0 =4 π⋅10 H / m -
magnetic constant, n - the number of turns per unit length of the solenoid.
Comparing the expressions (1) and (2) for inductance of a solenoid we obtain
L=μ 0 μn 2 lS=μ0 μn2 V (3)
If there is not core inside solenoid , the
L= μ 0 n2 lS= μ 0 n2 V (4)
where V =lS - the volume of the solenoid. From (3) and (4)
L=μL0 μ= L/ L 0
and (5)
The inductance can be determined more than by one way. One of these methods is the
method of Joubert. The essence of this method is as follows: R coil resistance in the DC circuit,
regardless of its shape, depends on the length, cross-sectional area and the conductor material.
This is called the ohmic resistance of the conductor or active resistance. If the conductor is fed
by AC voltage
U =U m cos2 πν t (6)
the alternating current flows in it
U Um
i= = cos 2 πν t =J m cos 2 πν t
R R (7)
U
where m - the voltage amplitude, ν - the frequency of its changes. If in circuit in addition to the
active resistance there is also an inductance L , the current in the circuit depending on the time
varies as:
i= J m cos( 2πν t− ϕ)
(8)
where
J m - the peak value of the current is determined from the expression:
Um
J m=
√ R 2 + 4 π 2 ν 2 L2 (9)
ϕ - the phase difference between voltage and current strength.
2 πν t RL
tg ϕ= cos ϕ=
R or Z (10)
From a comparison of (6) and (8) we see that the current lags
√ 2
the voltage by phase. Expression Z= R +4 π ν L from
2 2 2
the formula (9) is called impedance and R L=2 πν L is called inductive resistance. In formula (6)
and (7) we have the amplitude values of current
J m and voltageU m . But measuring devices
measure the current values (effective) of these
quantities
J g and U g . The connection between them is determined
A c by the ratio:

J m=J g √2 and
U =U √2
m g
Considering this in equation (9) we obtain:
Ug Ug
J g= J g=
Z or √ R2+4 π 2 ν 2 L2 (11)
Let us find out the inductance (9)
1
L=
2 πν
√ Z 2− R 2
(12)
U
Z= g
where Jg (13)
the impedance of solenoid. According to formula (12) by known Z , R and ν the inductance can
R A
be calculated. To do this, use the scheme shown in Figure 1. here e - a rheostat, c - key, L -
the coil with resistance R , A- ammeter, V - voltmeter.

Procedure and analysis

1. Remove the core from the coil and use the key to complete the circuit.
2. By changing the position of the slider rheostat, measure 5 different values of current
Jg
U
and voltage g .
3. Repeat these measurements after entering core into the coil .
4. Using the formulas (13) and (12) calculate the impedance and inductance of the solenoid
for the two cases.
5. Using the values of inductance of the solenoid with core (4) and without ( 0 ) it, using the
L

formula (5) calculate the permeability ( μ) .

6. Calculate the relative measurement error.

Measurement table.

Without Jg, A U g,V Z , Ohm L0 Hn

core
1
2
3

With core Jg, A U g,V Z , Ohm L0 Hn

1
2
3
Questions to the lab. The phenomenon of electro-magnetic induction. Self-inductance. Extra
current after closing and opening the circuit. The magnetic field strength inside and outside the
solenoid. The inductance of the coil. Alternating current.

LABORATORY № 25
STUDY OF THE HALL EFFECT
Objective: To study the Hall effect and the determination of the concentration of charge carriers
in semiconductors.
Accessories: The sample of crystalline silicon, permanent magnet, DC source, a microammeter,
milliammeter.
Works theory
American scientist Hall in 1880, based on conducted experiments discovered the following
phenomenon: if the metal plate along which flows a constant electric current, placed
perpendicular to the magnetic field, between faces parallel to the current and the field a potential
difference is produced. Its value is given by
JB
Δϕ= ϕ A − ϕc =R
b (1)
where J - current, B - magnetic field, b - width of the plate in the direction of the magnetic
field, R - different for different metals, the coefficient of proportionality, known as the Hall
constant. The phenomenon is called the Hall effect.
Hall phenomenon is observed not only in metals but also in semiconductors, and from the
sign of the effect can be determined belonging of semiconductor to the n - and p -type.

The Hall effect is very simple explained by the electronic theory. Let us assume that the
concentration of conduction electrons in a conductor is equal to n, and the average velocity of
ordered motion -ϑ . Then, the current in the conductor is equal to:
J= jS=en ϑ aв (2)

When the magnetic field perpendicular to the current, the Lorentz force acting on the moving
electrons, changing the trajectory, forward them to the upper face of the plate 1 (Figure 1). As a
→ →
result, between the surfaces 1 and 2 there is a transverse electric field. The force F =e E acting
on the electron in this field is directed against the Lorentz force. In the case of dynamic
equilibrium:

[ϑ ×Β ]=0
→ → →
e E +e
 Fig. 1

And from here

→
[ → →
]
E =− ϑ ×Β . As can be seen from the figure, the potential difference between
points A and C is equal to
Δϕ=ϕ A −ϕc =E⋅a=ϑ Ba
(3)
Taking into account (2) (3), we can write that
JB
Δϕ=ϕ A −ϕ c=
enb (4)
From a comparison of the formulas (4) and (1) must be:
1
R=
en (5)
Thus, by calculating the Hall coefficient, it is possible to determine the nature and concentration
of charge carriers. If we take into account the thermal electron velocity distribution, for the Hall
constant a more accurate expression is obtained:
R=3 π / 8 en (6)
from which for electron concentration:
3π
n=
8 eR (7)

To study the Hall effect using an experimental equipment, shown in Figure 2. Where 1 -
power supply 2- millivoltmeter, 3 - test sample, 4 - permanent magnet, 5 - milliamp.

+ DC
- source

Fig. 2

Procedure and analysis

1. Giving high voltage in the range of 1 - 3 V from the DC source to the sample , note the
corresponding values of current and potential difference.
2. Use the known geometric dimensions of the sample and the magnetic field to calculate the
concentration of electrons by the formula (7) .
3. Calculate the relative and absolute measurement error.

Measurement table.
 № J , mA Δϕ , mV n , m−3
1
2
3

Questions to the lab. Explanation of the Hall effect according to electronic theory. Features of
the Hall effect in metals and semiconductors. The mobility of the charge carriers.

LABORATORY № 26
THE STUDY OF THE MAGNETIC PROPERTIES OF FERROMAGNETICS
Objective: Experimental study of the magnetic properties of ferromagnet materials in an
alternating magnetic field and learning the skills of the research process of magnetization of
ferromagnetic materials with an oscilloscope.
Accessories: Sound Generator, two channel of oscilloscope, the sample (toroid), capacitors and
resistors.
Works theory
Ferromagnetics are the substances with high magnetic permeability. These include
Fe , Ni ,Co , Cd and their alloys with other metals. Ferromagnetic materials have a number of
features that distinguish them from other magnets. They tend to the phenomenon of hysteresis.
It consists in that the magnetic induction B in the ferromagnetic depends not only on the
value of the magnetizing field strength H at the moment, but also on how it was changing in the
previous time points. Therefore, the induction B is not a single-valued function
The concept of differential permeability μ is introduced for ferromagnets.
1 dB
μ=
μ0 dH (1)
If a ferromagnet placed in a magnetic field, which intensity gradually increases the
magnetization can be brought to saturation, and the dependence of B on H (magnetization curve)
will be expressed by portion OA (Figure 1). By reducing to zero of magnetizing field the
magnetization curve does not follow the original curve AO, but follows the AC curve. As a
result,
when removing the external magnetic field, ferromagnetic material is
B
magnetized with a residual induction г . It is necessary to make the
magnetic field with the reverse direction and the value H с for a complete
demagnetization of the sample. Hс is called the coercive force. Thus,
with an increase of H, the ferromagnetic material is completely
demagnetized at the point "C". With a further increase of the magnetic
field the ferromagnet is magnetized again, reaching a saturation point D.
As can be seen from figure 1, at a variable change in the direction of the
magnetizing field the dependence of the B from H is represented by a
Fig. 1 closed curve, which has the name of the hysteresis loop.
Nature of ferromagnetism was revealed by quantum mechanics. Under certain
conditions, in some crystals can occur so-called exchange forces that cause the magnetic
moments of the electrons to line up parallel to each other. As the result there are regions of
spontaneous (spontaneous) magnetization, which are also called domains (fig.2a.). domains have
dimensions of the order of 10-4-10-3 sm. Within each domain ferromagnet spontaneously
magnetized to saturation and has a certain magnetic moment. The directions of these moments
are different for different domains (Fig.2b), so that in the absence of an external field the total
moment of the whole body is zero. Effects of magnetic field on the ferromagnetic leads to a
rotation of the magnetic moments of the domains in the field direction (fig.2c).
The dependence of the directions of the magnetic moments of domains from the external
magnetic field direction leads to the formation of the hysteresis loop. When performing one
cycle of reversal magnetization of ferromagnet the work is numerically equal to the area of the
hysteresis loop. This work goes into heating the ferromagnet.
W =∫ BdH (2)

Fig.2а Fig.2b Fig.2c

Hysteresis loop can be observed on an oscilloscope screen (Figure 3).

Sound
Generator

oscilloscope
Fig. 3

The test sample is made in a toroidal shape, on the surface of which two coils are uniformly
wound with the numbers of turns per unit of length n1 and n2 . The first coil through the resistor
with resistance R1 is connected to the output of the sound generator with an output voltage of
sinusoidal waveform.
The magnetic fields in the toroid is defined by the formula:
H=n1 J 1
(3)
where J 1 - the current in the primary coil. The voltage drop in the resistor R1 .
U 1 =J 1 R 1
(4)
From (3) and (4) we get:
H =kU 1
(5)
n1
k=
Where
R1 .
 Since an alternating voltage is applied in the coil , according to the formula (3), the magnetic
field will change with the frequency of alternating current in a range from - H to + H . In the
secondary coil emf induction
dФ dB
ε 1 =−N 2 =−N 2 S
dl dt (6)
Here, N 2 - the number of turns in the secondary coil, Ф=ВS - the flux of the magnetic field
through the cross section of the toroid. According to Ohm's law, for the secondary coil:
ε =J 2 R2 + U c
U
where J 2 - the current in the secondary coil, c - the voltage across the capacitor. If R2 and
C - capacitance so large that J 2 R2 >> U c

εi N 2 SdB
J 2= =
R2 R2 dt ( 7)
In this case, the capacitor voltage
q ∫ J 2 dt N 2 S dB 2 N 2 SB 2
Uc= =
C C
=
R2 C
∫ dt
dt =
R2 C (8)

R2C
=K 2
Introducing the notation
N2 S

obtain
B2 =K 2 U C (9)
As seen from expressions (5) and (9), a voltage U 1 is proportional to the magnetizing field
U
strength, and c - magnetic induction in the sample. If the voltage U 1 is applied to the horizontal
deflection plates of the oscilloscope, the electron beam in the X-axis will deviate proportional to
H, and in the Y-axis direction proportional to the induction B. For a full cycle of changes of the
external field H, an electron beam of oscilloscope follows a closed hysteresis loop. By varying
the voltage across the primary winding obtain different sizes of loops. The top of each loop is a
point which corresponds to the saturation maximum of the basic magnetization curve. Voltages
U 1 and U C can be determined by knowing the voltages U x and U y causing the deviation of
electron beam by one division in the X and Y axes:
U 1 =n x U x and U C =n y U y
n n
where x and y - the coordinates of the vertices of the hysteresis loop.
Substituting the last expression in the formula (5) and (9) we get:

H=kU 1 =Knx U x =к x n x
B=K 2 U y n y=K y n y (10)
where
n 1U x R C
K x = KU x= K y= K 2 U y = 2 U y
R1 и N2S (11)
 Procedure and analysis
1. Connect the generator and oscilloscope to the power supply.
2. Project an electron beam to the center of the grid on the oscilloscope screen.
3. At a maximum output voltage of the generator, using handles "reinforce in vertical" and
"reinforce in horizontal" of an oscilloscope get the maximal possible hysteresis loop on the
oscilloscope screen.
4. By reducing the output voltage of the generator, get some of the hysteresis loops. Note for
each of them the coordinates of the vertices
n x and n y .

5. According to the formula (11) calculate

K x and K y .

6. Calculate the value

H=K x n x and B=K y n y for the vertex coordinates of all received loops.
7. According to the obtained data draw the graph of dependence B=f ( H ) .
8. Using the graph B=f ( H ) , draw the graph of dependence μ=f ( H ) .

Measurement table

№ nx ny Kx Ky H B ED=dsinϕ=IK λ

1
2
3

Questions to the lab. The magnetic field in the medium. Magnetics. Ferromagnetism. Hysteresis.
The phenomenon of electromagnetic induction. Lenz's rule.

Laboratory Work # 27
Determination of the refractive index of liquids by refractometer
Work Objective: The study of the work principle of the refractometer and determination of a
refractive index of various liquids.
Accessories: refractometer IRF-22, investigated liquids, dropper, cotton.

Short theoretical information

In this work we define the index of refraction of transparent liquids. The refractive index of
the substances can be determined in various ways. The method we use is based on the law of
total internal reflection.
As it is known, when a ray of light transits from an optically denser medium to a less dense
medium, refracted and deviates from the normal (Figure 1 a). It is obvious that with increasing
the incident angle, the intensity of the refracted beam decreases and the reflection intensity
increases. At a certain value of the incident angle io, the refracted ray glides over the interface of
two media (Fig.1b). In this case, the refractive angle is 90 o and the angle io of incidence is called
the limit angle. If the angle of incidence is greater this angle, the light ray not passing into the
second medium, undergoes total internal reflection (Fig. 1c).

Figure 1.
 According to the law of refraction
sini o n2 n2
o
= and sin i o=
sin 90 n1 n1
For precise and rapid determination of the refractive index of the medium are used a special
optical device - refractometer. There are different types of refractometers. In this study used the
refractometer IRF-22 (Abbe type refractometer.)
Installation Description

The refractometer IRF-22 determines the refractive index of liquids within range from 1.33
to 1.72. It consists of two rectangular prisms and telescope (Figure 2).

Figure 2.
The telescope consists of lenses. In the common focal plane of the lens is located cross,
formed by thin filaments. Telescope is strongly fixed, but holder with prisms can rotate. With
holder bonded pointer, which can move over the limb. Limb calibrated directly in the values of
the refractive index.
The prisms are made of high quality glass whose refractive index is 1.72. Rays' passing in
these prisms is shown in Figure 2. The beam reflected from the mirror surface is directed to the
BC side surface of ABC prism and after refraction it falls on the matted surface AC. Scattered at
different angles (from 0o to 90o) from the surface AC light beams then pass through the liquid
layer, located between the faces of the prism.
When the angle i of the incidence ray is i<io, the refracted light can passing
through the liquid, falls on the ACD prism and illuminates it. The rays with
angles of incidence i>io can't penetrate and illuminate ACD prism as a result of
total internal reflection. Therefore, the AD side face of the ACD prism is divided
into two parts - the illuminated and dark. Between them there is a sharp
boundary, determined by the fall angle i=io (Figure 3).
MN boundary position depends on the limiting angle io, which in turn Figure.3
depends on the refractive index of the liquid sample. Therefore, it is possible to
calibrate the scale of device, so that according a certain position of the border we directly
determine the refractive index of liquid.

Work progress

1. Slightly draw prisms apart, drips a few drops of sample liquid onto the bottom prism and
then push prisms together.
2. By observing through the eyepiece of the telescope and rotating special screw are seeking
the appearance of the illuminated and dark areas.
3. Turn the other screw to combine boundary between of light and shadow with the center
of the crossed filaments.
 4. According limb note the value of the refractive index liquid within 0.001. Repeat
measurements 3 times.
5. Draw prisms apart. Clean their faces with cotton. Drip a few drops of new sample liquid
onto the bottom prism and then push prisms together. Repeat experiments.
6. Calculate the absolute and relative experimental error

Data Table

№ n1 n2 n3
1
2
3

Questions for laboratory work. The laws of light reflection and refraction, relative and
absolute refractive indexes, the phenomenon of total internal reflection.

Laboratory work # 29
Determination of the laser wavelength using a diffraction grating.

Work Objective: The study of diffraction of monochromatic light using a diffraction grating.
Accessories: Laser, diffraction grating, screen, measuring ruler.

Theory.

Light rays in an optically homogeneous medium propagate rectilinearly. If light encounters an

obstacle in its path, then, deviating from the straight path, it penetrates into the region of
geometric shadow. This phenomenon is called diffraction of light. Diffraction is very strong
when the wavelength of light λ is comparable to the dimensions of the obstacle l, i.e. λ ⁓ l.
Of great practical importance is the diffraction observed when light passes through a two-
dimensional diffraction grating. A diffraction grating is the set of a large number of identical slits
spaced apart from each other at the same distance (Fig. 1).

A transmission grating can be made by cutting parallel grooves on a glass plate with a
precision ruling machine. The spaces between the grooves are transparent to the light and hence
act as separate slits. Diffraction gratings used in various areas of the spectrum differ in size,
shape, material of the surface, the profile of the grooves and their frequency (from 100 to 1200
grooves /mm).
If the width of each slit is equal a, and the width of the opaque sections between the slits is b,
then the quantity d = a + b is called slit separation (period) of the diffraction grating. Amplitudes
of oscillations of radiation of the same direction from all the slits are equal.
The result of the addition of secondary waves (wavelets) depends on the phase difference of
the rays from identical points of adjacent slits (for example, C and E). If the condition

ED = d∙sin φ = ± k∙λ, where k is the order of maximum k = 0, 1, 2, ... (1)

then, the constructive superposition of the waves (the maximum of interference) occurs and a
diffraction maximum is observed at the point C in the focal plane of the lens.
Let us consider a method for determining the wavelength of laser radiation using a diffraction
grating. The installation scheme is shown in Fig. 2

Monochromatic visible radiation from the optical quantum generator 1 (laser) falls on the
diffraction grating 2, located perpendicular to the direction of light propagation. The diffraction
pattern is observed on screen 3, located behind the diffraction grating.
Moving the screen, you can change the distance between the main maximums. Using the
condition of the maximum of the diffraction grating, it is possible to determine the wavelength of
monochromatic laser radiation.
From equation (1)
d ∙ sin φ
λ= (2)
k
 At small diffraction angles sin φ ≈ tg φ. From Fig.3 we can see that tg φ = x/L, where L is the
distance from the diffraction grating to the screen, x is the distance from the central maximum to
the k-order maximum. Taking this into account in (2), we have:

d ∙x
λ= (3)
k ∙L

Work Progress.

1. Turn on the laser

2. Set the screen at such a distance from the diffraction grating that it will produce a clear
image of several maxima.
3. Determine the distances x1, x2 and so on between the central maximum and the maxima of
the 1st, 2nd, 3nd orders.
4. Measure the distance from the screen to the diffraction grating L.
5. Calculate the wavelength according to known values x, L, d and k according to formula (3).
6. Repeat the test several times for each visible order of diffraction maximum.
7. Calculate the absolute and relative errors of the experiment.

Data table

№ k d ,m X ,m L,m λ,m
1
2
3
4

Questions to the laboratory work.

Diffraction of light. Fresnel diffraction. Diffraction from one, two and several slits. Diffraction
grating.

Laboratory Work # 31
Studying of the Malus's law and determination of the degree of polarization
of the laser radiation.

Work Objective: The study of the law of Malus and the determination of the degree of
polarization of laser radiation.
Accessories: Laser, polarizer, micro-ammeter and photocell.
Short theoretical information
 According to the wave theory, visible light is an electromagnetic wave. The electromagnetic
→ →
wave is transverse: the vectors of the electric E and magnetic H field strengths of the wave
are mutually perpendicular and lie in a plane perpendicular to the wave propagation velocity
→ →
vector , and the vectors E , H , and form the right-screw system.
→ →
In the natural light, the oscillations of the vectors E and H occur with equal probability in
all possible directions and these oscillations randomly replace one another. (Fig. 1a). Polarized is
the light in which the directions of the light vector are somehow ordered.

Figure 1

The light can be plane (or linearly) polarized, elliptically polarized, circularly polarized and
partially polarized. Light is called plane (or linearly) polarized if the oscillations of the light
vector occur only in one plane (Fig. 1b). For historical reasons, the plane of polarization was not
→
the plane in which the vector E oscillates but a plane perpendicular to it.
Linearly polarized light can be obtained from natural light by devices called polarizer (see
Figure 2). These devices freely pass vibrations parallel to the plane of the polarizer.

natural light polarizer Linearly polarized light

Figure 2

To study polarized light, another polarizer is used (it will be called an analyzer). We put two
polarizers in the path of the natural ray, the planes of which form an angle . Let the plane-
polarized light of amplitude Eo and intensity Jo ⁓ Eo2 fall on the analyzer, that is, the second
polarizer. Through the structure will pass the oscillation component with amplitude E = Eo∙cos.
Consequently, the intensity of the transmitted light is given by:
J= J 0 cos 2 ϕ
This relationship is called the law of Malus.
The light in which the oscillations of one direction prevail over the oscillations of other
directions is called partially polarized (Fig.1c).
If we pass partially polarized light through the polarizer, then as the device rotates around the
beam direction, the intensity of the transmitted light will vary from Jmax to Jmin (Fig. 1d), and the
transition from one of these values to the other will occur when rotates to the angle  = π/2.
The degree of polarization is the expression:
J max −J min
P=
J max + J min (1)
For plane-polarized light Jmin = 0 and P = 1; For natural light Jmax = Jmin and P = 0.
 →
Light is called elliptically polarized if the light vector (vector E ) changes with time so that its
end draws an ellipse (Fig. 1e). Elliptically polarized light can be obtained by superimposing two
coherent plane polarized lightwaves with a certain phase difference of oscillations whose
oscillation planes are mutually perpendicular. When the phase difference is equal to an odd
number of π/2, and the equal amplitudes of the waves, the ellipse becomes a circle (Fig. 1f).

Installation Description

The scheme of the experimental setup is shown in Figure 3. A polarized light beam from the
laser 1 is incident on the polarizer mounted on the rim 2. The polarizer can rotate together with
the angle indicator 3 relative to the fixed disk 4. The disk has a scale, allowing to determine the
angle of rotation. Passing through the polarizer, the light hits the surface of the photodiode 5.
Under the action of light, a photo-emf is produced in the photodiode. The voltage on the
photodiode is proportional to the light intensity. Considering that the photocurrent is proportional
to the intensity of the incident light, we can write: i ⁓ J.

Figure 3

The work progress

1. With the laser turned off, determine the zero point of the microammeter when the
photocell is open (background photocurrent).
2. Turn on the laser, determine the current io corresponding to the maximum intensity of
light passing through the polarizer.
3. Rotate the polarizer to the different angles  and note the corresponding values of the
current in the table.
2
4. Plot the graph of i=f ( cos ϕ ) dependency according to the table.
5. Determine the degree of polarization according to formula (1).
6. Repeat experiment 6 times.

Data Table

i cos ϕ cos 2 ϕ
, degree
0
10
20
30
....
90
100
 i max i min ϕ max ϕ min Δϕ
d(l/2) d⋅X
№ λ= =
LK L⋅K

1
2
3

Questions for laboratory work. Polarization of light. The laws of Malus and Brewster.

Laboratory Work # 32
Determination of the Stefan-Boltzmann constant.
Work Objective: Studying of Stefan - Boltzmann's law and get acquainted with one of the
methods of determining of Stefan - Boltzmann constant by optical pyrometer.
Accessories: Installation for determining the Stefan - Boltzmann constant, power meter,
optical pyrometer.
Short theoretical information

All bodies at any temperature radiate electromagnetic waves. These waves are caused by
chaotic thermal motion of atoms and molecules that make up the body, and such radiation is
called thermal radiation. The energy of the radiation corresponding to different regions of the
spectrum, is not the same and depends on body temperature. For example, at a temperature of
900 - 1000 K, the maximum radiated energy is in the infrared region of the spectrum. With
increasing temperature the fraction of radiation energy in the visible part of the spectrum
increases.
Quantitative characteristic of thermal radiation is the spectral density of body emittance
(radiant emittance)- the radiated energy from unit surface area per unit frequency range:

(1)
where dWf,T - the energy of the electromagnetic radiation emitted per unit time from an area dA of
the body surface at temperature T in the frequency range of f to (f + df).
The ability of body to absorb the radiation incident upon them is characterized by spectral
absorptivity:

(2),
showing absorbed part of the electromagnetic wave energy incident per unit body surface area at
frequency region of f up to (f + df) by the body. Here dW - incident energy of f up to (f + df)
region and dWabsor - absorbed energy at the same region of frequencies.
The body with ability to absorb entirely all incident radiation at all temperatures and any
frequency, called a perfect blackbody. Consequently, the absorptivity of a perfect blackbody for
all frequencies and temperatures are identically equal to unit .
Based on the thermodynamics and analyzing equilibrium radiation conditions in an isolated
system of bodies Kirchhoff found that the ratio of the emittance and absorptivity do not depend
on the nature of the body, it is the same universal function of frequency and temperature for all
bodies and is equal to the emittance of the perfect blackbody Ef,T,

(3)
The energy flow emitted by the unit surface of the blackbody in all directions (within a solid
angle 2), called irradiance (integral emissivity) of the body RT.
 (4)
Based on thermodynamic considerations, Stefan and Boltzmann in 1884 concluded that
blackbody irradiance is proportional to the fourth power of the temperature, i.e.,
R T =σT 4 (5)
where σ = 5,67∙10-8 Wt/(m2∙K4) is Stefan-Boltzmann constant.
For all not perfect black bodies irradiance is proportional to the fourth power of the
absolute temperature too:
(6)
where ε - emissivity, which is a value between 0 and 1 (ε= 1 for perfect blackbody). ε is a
ratio of the radiant emittance of the body at a certain temperature to the radiant emittance of a
black body at the same temperature.
Installation Description
According to the Stefan-Boltzmann law, the body of temperature T, surrounded by the
environment at a temperature To radiates energy from the unit surface area per second:
(7)
If it is known numerical value of ε, it is necessary to determine the magnitude of R', T and To.
For example, if the emitting of glow body has the form a spiral, the radiant energy can be
determined from the calculation power required for heating spiral. We assume that the entire
amount of heat released in the spiral goes on the radiation, then:

(8)
where - J current, - V voltage drop on the spiral A - the area of the radiating surface and P -
the current capacity. From the expressions (7) and (8) σ can be obtained:

(9)
The experimental setup is shown in Fig.1. Here 1 - photoelectric pyrometer, 2 - filament lamp
3 - power meter, and 4 - the power supply.

Figure 1

Photoelectric pyrometer is a device for determining the

temperature of the glow-spiral. Diagram of the
photoelectric pyrometer is shown in Figure 2. Where 1-
the protective glass, 2 - a housing, 3 - the diaphragm, 4-
photodiode, 5 - amplifier and 6 - measuring device
Figure 2
Work progress

1. Connect the device to a voltage of 220V, for heating spiral. Rotate the auto-transformer in one
direction or another to observe changes in the glowing of spiral.
2. Determine temperature of the spiral at various currents not less than 5 times. At the same time
noting the room temperature.
 3. Calculate the value of the Stefan - Boltzmann constant on the basis of formula (9).
4. Calculate the average value of the Stefan - Boltzmann constant, and measurement uncertainty.

Data Table

№ Power Temperature σ <σ >

P, Wt Room Spiral Wt/(m ∙K4)
2

t 0 ,0 C t,0 C T ,K
1
2
3

Questions for laboratory work. Thermal radiation. Radiation of perfect blackbody. Kirchhoff's
law, Stefan - Boltzmann and Wien laws. Pyrometry.

Laboratory work № 33
Definition of the integrated sensitivity of a photocell.
Work Objective: Study of the photoelectric phenomenon, determination of the integrated
sensitivity of a photocell.
Accessories: Photocell, micro-ammeter, optical bench, light source (standard filament lamp),
power source.
A brief theory of work.
Part of the light incident on the surface of the substance is absorbed by the atoms of
substance. As a result, certain optical physical phenomena occur. One of these phenomena is the
photoelectric effect. The phenomenon of the emission of electrons under the action of
electromagnetic radiation is called the external photoelectric effect (photoelectric effect). In
studying the photoelectric effect, the following regularities were established:
1. The maximum initial speed of photoelectrons is determined by the frequency of light and
does not depend on its intensity.
2. For all substances there is a red border of the photoelectric effect, i.e., the smallest
frequency fo at which an external photoelectric effect is still possible.
3. The number of photoelectrons ejected from the substance per unit time (photocurrent of
saturation) is directly proportional to the intensity of light.
These regularities were explained by A. Einstein on the basis of his proposed quantum theory
of the photoelectric effect. According to this theory, each quantum of light is absorbed by only
one electron. Therefore, the number of ejected photoelectrons should be proportional to the
intensity of light. The energy of the incident photon is expended on the electron to perform the
work of the output A from the substance and on the message to the kinetic energy emitted by the
photoelectron

(1)
Equation (1) is called the Einstein equation for the external photoelectric effect.
It is possible that the quantum energy absorbed by electrons is insufficient for their emitting
from matter. In this case electrons leave atom, stay inside matter and the number of free electrons
increase, which leads to a decreasing of the electrical resistance of the substance. This
phenomenon is called the internal photoelectric effect, which is observed in some dielectrics and
semiconductors. Devices working on the basis of an internal photoelectric effect are called
photocells.
 In this work is used a selenium photocell with a
barrier layer. The selenium photocell consists of a
metal plate with a thin (0.1 mm) selenium film
applied on its surface (Fig. 1).
Selenium film is covered with a very thin (10 -6 m)
layer of gold (this layer in the figure is enlarged).
At the place of contact of the metal with the
semiconductor, a barrier layer (Q) is formed, Which
allows electrons to pass only in one direction. When
the sensitive surface of a photocell is illuminated,
free electrons form as a result of the internal
photoelectric effect.
As a result of chaotic motion, electrons diffuse through the barrier layer and an excess of
electrons is formed in the metal near this layer. The semiconductor, which has lost electrons, is
charged with a positive charge. Thus, a potential difference is created between the semiconductor
and the metal and the resulting current is detected by a micro-ammeter.
Photocells with a barrier layer are working as a current generator, converts light energy into
electrical energy. In barrier layer elements, semiconductors such as selenium, copper oxide,
potassium, germanium and antimony are used. The current produced by the action of light is
called a photocurrent, and its magnitude i is directly proportional to the luminous flux Φ falling
on the photosensitive surface of the photocell:
i= γФ (2)
Where γ, is one of the main characteristics, and called the photosensitivity of a photocell.
The integral sensitivity of a photocell is equal to the photocurrent created by a unit luminous
flux.
i
γ=
Ф,
(3)
The spectral sensitivity of a photocell is a quantity that is equal to the photocurrent created by
a unit of monochromatic luminous flux.
If E is the illuminance of the surface of the photocell, and A is the surface area, then the
luminous flux will be
Ф = E∙A ( 4)
A point source with a luminous intensity J at a distance R creates an illuminance
J
E = 2 cos α
R (5)
Then the luminous flux incident on the circular surface of the photocell with a diameter d is
determined by the expression:
πd 2 J
Ф= ⋅ 2 cos α
4 R (6)
where α - the angle between the light ray and the normal to the surface. Taking into account (6)
in (3), for the sensitivity of the photocell, expression
4 R2 i
γ=
πd 2 J cos α (7)
If the light beam falls perpendicular to the surface, then cos α = 1 and
4 R2 i
γ=
πd 2 J (8)
 Installation Description

The experimental setup is shown in Fig.2. Here S is the light source.

Photocell

88
Scale
mkA

Fig. 2
Work Process

1. After installing the photocell, note the distance to the light source.
2. After connecting the micro-ammeter to the photocell, illuminate the photocell with a
reference lamp and note the photocurrent strength that has arisen.
3. Having measured the diameter of the photosensitive surface of the photocell, calculate by
its formula 8 its sensitivity.
4. Repeat the experiment for different distances between the photocell and the light source.
5. On the basis of the data obtained, calculate the relative error of the experiment.

Data Table.

№ R, m i, mkA d, m J, cd γ, A/lm
1
2
3
4

Questions to the laboratory work. The phenomenon of the photoelectric effect, the internal
and external photoeffect.Retarding voltage. Laws of photoelectric effect. Photometry.

Laboratory work № 34
Determination of Planck's constant by using LED.
Work Objective: Studying one of the methods for the determination of the Planck constant.
Accessories: LED, rectifier, voltmeter, an optical table, diffraction grating, ruler.
 A brief theory of work.
In 1900, German physicist Max Planck made the assumption that the electromagnetic radiation has
not only the wave but also a quantum (corpuscular) properties. Having studied the spectral density of the
irradiance absolutely black body, Planck proposed the quantum hypothesis, according to which the heated
body doesn’t radiate energy continuously, but with a certain portions - quants, where the energy of quant
is determined is E=hf ,where f - frequency of the radiation, and h- Planck's constant. Planck's constant is a
fundamental physical constant. Unit for Planck's constant is [h] = J×s
Determination of Planck's constant in this work based on the study of the characteristics of Light
emitting diode (LED) - the device that converts electrical energy into light. Below is detailed information
on the semiconductor diode and LED.
Electro-conductivity of semiconductors is intermediate between dielectrics and conductors. In the n-
type semiconductors majority carriers are electrons and in the p-type semiconductors - positive "quasi-
particles" called "holes".
In contact of these two different types of semiconductors
(1a) electrons of the n- type semiconductor diffused into the
p - type semiconductor and the holes from the p - type
semiconductor into the n- type semiconductor. As a result,
unbalanced positive charge is collected in the border layer of
n-type semiconductor and negative charge is collected in the
border layer of p-type semiconductor. These contact areas
are known as p-n or n-p junctions. Inter-diffusion continues
as long as the contact potential difference reaches a certain
value Ucon (or a certain value of the electrostatic field E). If a
direct voltage is applied to the external contacts of
semiconductors (1b) the electric field arises which opposed
to the contact potential difference.
This field reduces the width and the electrical resistance of the barrier layer. As a result, the number of
particles, passing through the n-p junction increases sharply and an electric current arises.
If you apply a reverse voltage, i.e., connect the n- type semiconductor to a positive and p- type to the
negative terminal of the current source, in this case through n- p junction the electric current does not
flow. Thus, the device with n- p junction acts as a rectifier, i.e., current flows in one direction only
through the system (diode).
On the other hand, on the basis of the n- p junctions can
be created devices (by selection of appropriate materials),
which emit light due to the transition of electrons in the p -
region and recombination with holes when they connected to
power supply directly and U>Ucon. Emission may be
accompanied also by transition of the holes in the - area.
This system continuously emits light and is called a LED
(LED). (Fig.2) LED is a device for converting electric
energy directly into light.
Usually LEDs made of type AIII BV compounds with eV band of gap zone 1,5-2 eV (for example GaP -
gallium phosphide), which emit red or green light. Volume of LED is only 200 mm3. With low-cost, long
service life and negligible power consumption LEDs are widely used in electronics and daily life.
 LED Operation. With an increase in the direct voltage
applied to the LED, the current increases very slowly. After
achieving a certain voltage value it begins a sharp rise in
current, whereby the LED starts to emit light. The
dependence of the current strength of the voltage is shown in
Figure 3. At each act of recombination of an electron with a
hole emitted photon with energy E = hf. With the passage of
electrons through the n-p junction the external electric field
does work A = eUo, where f- where emission frequency, e -
electric charge of the electron, Uo - the magnitude of voltage
needed to p-n junction of LED to emit a light. In this way:
eUo
hf =e U o or h=
f
e Uo
and h= (1)
c
Here we replaced the frequency in accordance to the formula: f=c/.
This expression is the working formula for the determination of the Planck constant. Thus, to find the
h empirically, it is necessary to know the numerical values Uo and . The value of Uo is determined from
the readings of the voltmeter connected to LED.
To determine the length of the monochromatic
radiation is used a diffraction grating. Instead of the
lens and the screen, traditionally used to determine
the wavelength by means of a diffraction grating,
will use the eye: the lens plays a role of an optical
system of the eye and the screen - its retina (Figure
4). If direct look at the LED through the diffraction
grating, the observer will watch a diffraction
pattern. According to the condition of the
diffraction peaks: d∙sin= k (d - is the lattice
constant, and k- order of maximum) wavelength can
be determined.
d ∙ sin
¿ (2)
❑
On the other hand, as seen from Figure 4,

l/2 X
tg= = ∧sin ≈ tg
L L
so:
l
d ∙( )
2 d ∙X (3)
¿ =
Lk Lk

Work Process

1. Assemble the electric circuit as shown in Figure 5, and pay

attention to the correct connection polarity power supply to
LED.
2. To achieve a LED emission by varying the voltage.
3. Mark voltage at which emission process begins. Repeat
experiment at least 5 times.
4. Slowly raising the voltage across the LED, up 0.5, to
observe obtaining of consequent peaks through the
diffraction grating.
5. By selecting a certain distance between the grating and LED, noting the distances X1 and X2
between the center and the various peaks on either side of it.
6. Repeat measurements of paragraph 5, for different values of L.
7. According to the formula (3) calculate  and ❑ for each pair of X and L.
8. On the basis of formula (1) calculate the Planck's constant
e Uo❑
h=
c
Assess the difference between the calculated and the known Planck constant by comparing the
results obtained (U o ∧❑ are average values of voltage and wavelength).

Data Table 1

№
Uo,i Uo
1
2
3
4
5

Data Table 2

L k x1 x2 l=x 2 −x 1  ❑
L1 1
2
3
L2 1
2
3

Questions to the laboratory work. Planck's hypothesis. Planck's constant. Photons. The light diode and
how it works.