PLC Connection Guide

CROUZET M3 (FBD)

HMI Setting:
Parameters Recommended Options Notes
PLC type CROUZET M3 (FBD)
PLC I/F RS232
Baud rate 115200
Data bits 7
Parity Even
Stop bits 1
PLC sta. no. 1
*Support communications between HMI and PLC in pass-through mode
*Set LW-9903 to 2 to enhance the speed of download/upload PLC program in
pass-through mode

Device Address:
Bit/Word Device type Format Range Memo
B I DD 1 ~ 99 Input
B SLI_Bit DDh 10 ~ 24f Serial link input
B SLO_Bit DDh 250 ~ 48f Serial link output (read only)
B State D 1 State in PLC (read only)
W AI DD 1 ~ 99 Analogy input (default: 1 ~ 4)
W SL_IN DD 1 ~ 24 Serial link input
W SL_OUT DD 25 ~ 48 Serial link output (read only)
W Time D 1~6 Time & Day*
W Order D 1 Command** (write only)
W ID_Table DD 1 ~ 22
* address 1: second, address 2 : minute, address 3 : hour , address 4 : day, address 5 :
month, address 6 : year. The value range for “Year” is 0~99, entering “0” represents year
2000, entering “99” represents year 2099.
** run mode write 2, stop mode write 1.
 PLC Connection Guide

Wiring Diagram:
CROUZET M3: RS-232 9P D-Sub (Diagram 1 ~ Diagram 4)
Diagram 1
cMT Series cMT3071 / cMT3072 / cMT3090 / cMT3103 / cMT3151

eMT Series eMT3070 / eMT3105 / eMT3120 / eMT3150

MT-iE MT8070iE / MT6070iE / MT8100iE / MT8121iE / MT8150iE /

MT8071iE / MT6071iE / MT8072iE / MT6072iE / MT8073iE /
MT8101iE / MT8102iE / MT8103iE

MT-XE MT8121XE / MT8150XE / MT8090XE / MT8092XE

MT-iP MT6103iP / MT8102iP

HMI PLC
COM1 RS232
RS232 9P D-Sub
9P Female (Extension cable)

Rx 2 2 TX
Tx 3 3 RX
GND 5 5 GND
RTS 7 4 DTR
 PLC Connection Guide

Diagram 2
cMT Series cMT-SVR / cMT-G01 / cMT-G02 / cMT-HDM / cMT-FHD

mTV mTV

HMI PLC
COM1 RS232
RS232 9P D-Sub
9P Female (Extension cable)

Rx 2 2 TX
Tx 3 3 RX
GND 5 5 GND
0V External Power Supply
+5V External Power supply 4 DTR

Diagram 3
MT-iE MT8050iE / MT8053iE

MT-iP MT6051iP / MT8051iP

HMI PLC
COM1 RS232
RS232 9P D-Sub
9P Female (Extension cable)

Rx 9 2 TX
Tx 6 3 RX
GND 5 5 GND
TX+ 4 4 DTR
 PLC Connection Guide

Diagram 4
MT-iP MT6071iP / MT8071iP

HMI PLC
COM1 RS232
RS232 9P D-Sub
9P Female (Extension cable)

Rx 9 2 TX
Tx 6 3 RX
GND 5 5 GND
RTS 7 4 DTR

(3m serial link cable)

Note: Please use 3m serial link cable
(Accessories from Millenium 3) and extension
cable (as shown) to communicate with HMI
series.