Scribd
Upload
8 views

Resistor Circuits

1. This experiment investigates the relationships between current, voltage and resistance in series and parallel circuits. Key relationships for series and parallel circuits will be experimentally determined and compared to theoretical predictions. 2. The behavior of circuit elements like resistors and light bulbs will be examined to see if they follow Ohm's law. Measurements of voltage and current across individual components and entire circuits will be made using voltmeters and ammeters. 3. Data will be collected and plotted to analyze the resistance of individual components, and the effective resistance of series, parallel and compound circuits. The results will be used to study how circuit elements behave and whether they follow theoretical predictions.

Uploaded by

hsejmal12345
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
8 views

Resistor Circuits

1. This experiment investigates the relationships between current, voltage and resistance in series and parallel circuits. Key relationships for series and parallel circuits will be experimentally determined and compared to theoretical predictions. 2. The behavior of circuit elements like resistors and light bulbs will be examined to see if they follow Ohm's law. Measurements of voltage and current across individual components and entire circuits will be made using voltmeters and ammeters. 3. Data will be collected and plotted to analyze the resistance of individual components, and the effective resistance of series, parallel and compound circuits. The results will be used to study how circuit elements behave and whether they follow theoretical predictions.

Uploaded by

hsejmal12345
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

PHYSICS 111 LABORATORY

Experiment #3
Current, Voltage and Resistance in Series and Parallel Circuits

This experiment is designed to investigate the relationship between current and potential in
simple series and parallel resistor circuits using ideas of conservation of energy and conservation of
charge. In addition the effective resistance of the series and parallel circuits will be determined and
compared to theoretical predictions. Ohm’s Law, the proportionality between voltage and current, is
true for many things that conduct current but not for everything. Conductors, which do have
V
resistance, always yield the same ratio no matter what voltage you apply to it. Then it is possible
I
V
to say that = R is the resistance, because the ratio is always the same. In this experiment we will
I
also investigate the applicability of Ohm’s law to circuit elements.
€
To measure the electrical potential difference across an element in a circuit, a voltmeter is put
€
across its terminals. In other words, the voltmeter is connected in parallel with the circuit element.
The internal resistance of the voltmeter is huge compared to the resistance of the circuit element
being measured and since elements in parallel have the same potential differences a small amount of
current goes to the meter, enough for the meter to make a measurement. The remaining (larger
amount) of current passes through the circuit element.

To measure the current flowing through a circuit element an ammeter must be inserted in series
with the element where the current must flow through the ammeter in order to be measured. The
ammeter has a negligible resistance and thus does not affect the total circuit resistance. However,
one should be careful to never insert the ammeter in parallel around the circuit element. In parallel
the ammeter will have essentially the entire current pass through it blowing the fuse in the meter.
Again, since elements in parallel have the same potential differences, the lower resistance element
will get the greater share of the current. In this case it will be the ammeter. On a similar note, one
should take care not to wire the voltmeter in series with the circuit element, not because you will hurt
the meter, but because the resistance of the meter is so large in voltmeter setting that a negligible
current will be drawn from the power supply.

The voltage source in this experiment is an electronic “power supply” whose output voltage can
be varied from zero to about 10 volts. You will measure current and voltages with a digital
“multimeter” or DMM, so called because this versatile measurement device can measure several
electrical properties, including voltage, current and resistance.
1. Determining the resistance of a resistor
• Choose 3 resistors and record their actual resistances using the DMM provided. The
resistors will simply plug into the DMM in the COM/Ω terminals and if you set the
DMM to measure resistance, the resistance will be displayed.
• For each resistor you have, wire it in a circuit as shown in Figure 1.
• Select 10 potential differences and measure the corresponding potential differences
across the resistor and the current through the resistor as measured on each of the
DMM’s.

• Plot the potential difference versus the current for each resistor you have on the same
graph.
• If the data are linear, fit the data with a straight line and determine the experimental
values of the resistance for each resistor.
• How do these values compare to the values you measured?
• Does each of your resistors follow Ohm’s law?

Figure 1: Wiring diagram for a single resistor


connected to a battery VB. The voltmeter is placed in
parallel around the resistor R to measure the potential
difference across the resistor VR while the ammeter A
is placed in series to measure the current I that flows
through the resistor.
2. Series Circuit
• Choose two resistors and wire the series circuit as shown in Figure 2. You will need
3DMM’s for this part of the experiment.
• Set a potential difference VB = 2V and determine the current through each resistor at a
point before R1 , between R1 and R2 , and after R2 by using the DMM in ammeter mode.
What can you conclude about the current flow through each resistor in a series circuit?
• Next for VB = 2V, 4V, 6V, and 10V , measure the corresponding current through the
€
circuit for each of these potential differences. In addition measure the potential
€ € € €
difference across each of these resistors.
• Make a plot of VB , VR1 , and VR 2 versus I on the same graph.
€
• For a given value of the current, what can you conclude about the potential differences
across each resistor compared to the potential difference of the battery?
• From your plot, experimentally what can you conclude about the effective circuit
€
resistance?
• Does your result agree with theory?

Figure 2: Wiring diagram for two resistors wired in


series and connected to a battery VB. Each voltmeter is
placed in parallel around the resistor R to measure the
potential difference across the resistor VR while the
ammeter A is placed in series to measure the current I
that flows through the resistor combination.
3. Parallel Circuit
• Choose two resistors and wire the series circuit as shown in Figure 3. You will need
3DMM’s for this part of the experiment.
• Set a potential difference VB = 2V and determine the current through each resistor at the
points A, B, and C using the DMM in ammeter mode. What can you conclude about the
across each resistor in a parallel circuit?
• Next for VB = 2V, 4V, 6V, and 10V , measure the corresponding current at points A and
€
B for each of these potential differences. In addition measure the potential difference
across each of these resistors.
• Make a plot of VB , VR1 , and VR 2 versus I on the same graph.
€
• For a given value of the potential difference, what can you conclude about the current that
flows through each resistor?
• From your plot, experimentally what can you conclude about the effective circuit
€
resistance?
• Does your result agree with theory?

Figure 3: Wiring diagram for two resistors wired in parallel


and connected to a battery VB. The voltmeter is placed in
parallel around each resistor R to measure the potential
difference across the resistor VR while the ammeter A is
placed in series after each resistor to measure the current I
that flows through a given resistor and also to measure the
total circuit current.
4. Compound Series and Parallel Circuit
• Using all three of your resistors, wire the compound series and parallel circuit as shown
in Figure 4. You will need 3DMM’s for this part of the experiment.
• Set a potential difference VB = 2V and determine the current through each resistor at the
points A, B, and C using the DMM in ammeter mode. What can you conclude about the
across each resistor in a parallel circuit?
• Next for VB = 2V, 4V, 6V, and 10V , measure the corresponding current at points A and
€
B for each of these potential differences. In addition measure the potential difference
across each of these resistors.
• Make a plot of VB , VR1 , and VR 2 versus I on the same graph.
€
• For a given value of the potential difference, what can you conclude about the current
that flows through each resistor?
• From your plot, experimentally what can you conclude about the effective circuit
€
resistance?
• Does your result agree with theory?

Figure 4: Wiring diagram for a compound circuit.

5. Deviations from Ohm’s Law


• For the other circuit element given, a light bulb, wire the circuit again shown by Figure 2.
• Select 10 potential differences and measure the corresponding potential differences
across the light bulb and the current through the light bulb as measured on each of the
DMM’s.
V
• Plot the potential difference versus the current for light bulb as well as versus I for the
I
light bulb.
• From your plots, experimentally what can you conclude about the behavior of the device?
Is there a unique resistance that you can assign to the device? €
€

You might also like