Scribd
Upload
45 views

Worked Example-3 On Strip Methods

This document contains tutorial material on the strip method for slab design presented by Duresa Dubale. It includes 6 examples of applying the strip method to analyze and design different slab configurations under various support conditions. For each example, the document shows the analysis using the strip method to determine design moments, and provides instructions for students to complete the design by checking the slab depth, designing reinforcement, and checking deflection. The document aims to teach structural engineering students how to use the strip method to analyze and design slabs.

Uploaded by

Tadesse Megersa
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
45 views

Worked Example-3 On Strip Methods

This document contains tutorial material on the strip method for slab design presented by Duresa Dubale. It includes 6 examples of applying the strip method to analyze and design different slab configurations under various support conditions. For each example, the document shows the analysis using the strip method to determine design moments, and provides instructions for students to complete the design by checking the slab depth, designing reinforcement, and checking deflection. The document aims to teach structural engineering students how to use the strip method to analyze and design slabs.

Uploaded by

Tadesse Megersa
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 82

December-2022

STRUCTURAL DESIGN
CEng5123
Chapter Two: Strip Method for Slabs
Tutorial One
Duresa Dubale (MSc.)
29-Dec-22 By: DURESA DUBALE 2
29-Dec-22 By: DURESA DUBALE 3
29-Dec-22 By: DURESA DUBALE 4
29-Dec-22 By: DURESA DUBALE 5
29-Dec-22 By: DURESA DUBALE 6
29-Dec-22 By: DURESA DUBALE 7
29-Dec-22 By: DURESA DUBALE 8
29-Dec-22 By: DURESA DUBALE 9
29-Dec-22 By: DURESA DUBALE 10
29-Dec-22 By: DURESA DUBALE 11
29-Dec-22 By: DURESA DUBALE 12
29-Dec-22 By: DURESA DUBALE 13
29-Dec-22 By: DURESA DUBALE 14
December-2022

STRUCTURAL DESIGN
CEng5123
Chapter Two: Strip Method for Slabs
Tutorial Two
Duresa Dubale (MSc.)
29-Dec-22 By: DURESA DUBALE 16
29-Dec-22 By: DURESA DUBALE 17
29-Dec-22 By: DURESA DUBALE 18
29-Dec-22 By: DURESA DUBALE 19
29-Dec-22 By: DURESA DUBALE 20
29-Dec-22 By: DURESA DUBALE 21
29-Dec-22 By: DURESA DUBALE 22
29-Dec-22 By: DURESA DUBALE 23
29-Dec-22 By: DURESA DUBALE 24
29-Dec-22 By: DURESA DUBALE 25
Submission Date: Next Class (Before class start)

Assignment-2:
Part-1: Finish the design of Example-2
1) Check depth for flexure
2) Design the reinforcement
3) Check depth for deflection

29-Dec-22 By: DURESA DUBALE 26


29-Dec-22 By: DURESA DUBALE 27
29-Dec-22 By: DURESA DUBALE 28
29-Dec-22 By: DURESA DUBALE 29
29-Dec-22 By: DURESA DUBALE 30
29-Dec-22 By: DURESA DUBALE 31
29-Dec-22 By: DURESA DUBALE 32
29-Dec-22 By: DURESA DUBALE 33
29-Dec-22 By: DURESA DUBALE 34
29-Dec-22 By: DURESA DUBALE 35
29-Dec-22 By: DURESA DUBALE 36
29-Dec-22 By: DURESA DUBALE 37
29-Dec-22 By: DURESA DUBALE 38
29-Dec-22 By: DURESA DUBALE 39
29-Dec-22 By: DURESA DUBALE 40
29-Dec-22 By: DURESA DUBALE 41
29-Dec-22 By: DURESA DUBALE 42
29-Dec-22 By: DURESA DUBALE 43
29-Dec-22 By: DURESA DUBALE 44
Example 4 (Rectangular slab; One short edge unsupported)
Determine the design moments for the 150mm thick slab panel shown below. The
design load is 14.0kN/m2.

29-Dec-22 By: DURESA DUBALE 45


Solution:
1. Analysis (Using Strip Method)
• The discontinuity lines are selected as shown in the figure
below.
• Edge strip width = b/4= 4/4=1m
• Use ratio of support moment to span moment = 5:1

29-Dec-22 By: DURESA DUBALE 46


29-Dec-22 By: DURESA DUBALE 47
29-Dec-22 By: DURESA DUBALE 48
29-Dec-22 By: DURESA DUBALE 49
29-Dec-22 By: DURESA DUBALE 50
29-Dec-22 By: DURESA DUBALE 51
Submission Date: Next Class (Before class start)

Assignment-2:
Part-2: Finish the design of Example-4
1) Check depth for flexure
2) Design the reinforcement
3) Check depth for deflection

29-Dec-22 By: DURESA DUBALE 52


Example 5 (Rectangular slab; One Long edge unsupported)

Loads from floor finish and partition wall were ignored!

29-Dec-22 By: DURESA DUBALE 53


29-Dec-22 By: DURESA DUBALE 54
29-Dec-22 By: DURESA DUBALE 55
29-Dec-22 By: DURESA DUBALE 56
29-Dec-22 By: DURESA DUBALE 57
29-Dec-22 By: DURESA DUBALE 58
29-Dec-22 By: DURESA DUBALE 59
29-Dec-22 By: DURESA DUBALE 60
29-Dec-22 By: DURESA DUBALE 61
29-Dec-22 By: DURESA DUBALE 62
29-Dec-22 By: DURESA DUBALE 63
29-Dec-22 By: DURESA DUBALE 64
29-Dec-22 By: DURESA DUBALE 65
29-Dec-22 By: DURESA DUBALE 66
Example 6 Rectangular slab; (Slab with hole)

29-Dec-22 By: DURESA DUBALE 67


29-Dec-22 By: DURESA DUBALE 68
29-Dec-22 By: DURESA DUBALE 69
29-Dec-22 By: DURESA DUBALE 70
29-Dec-22 By: DURESA DUBALE 71
29-Dec-22 By: DURESA DUBALE 72
29-Dec-22 By: DURESA DUBALE 73
29-Dec-22 By: DURESA DUBALE 74
29-Dec-22 By: DURESA DUBALE 75
29-Dec-22 By: DURESA DUBALE 76
29-Dec-22 By: DURESA DUBALE 77
29-Dec-22 By: DURESA DUBALE 78
29-Dec-22 By: DURESA DUBALE 79
29-Dec-22 By: DURESA DUBALE 80
Submission Date: Next Class (Before class start)

Assignment-2:
Part-3: Finish the design of Example-6
1) Check depth for flexure
2) Design the reinforcement
3) Check depth for deflection

29-Dec-22 By: DURESA DUBALE 81


THANK YOU!

29-Dec-22 By: Duresa Dubale 82

You might also like