20-11-2023

Building Components
and Structures
Foundations

Introduction
Every structure consists of two parts.
(1) Foundation and (2) Super structure.
• The lowest artificially prepared parts of the structure which are in direct contact with
the ground and which transmit the loads of the structure to the ground are known as
Foundation or Substructure.
• The solid ground on which the foundation rest is called the “foundation bed” or
foundation soil and it ultimately bears the load and interacts with the foundations of
buildings.

1
 20-11-2023

Objects of foundations:
Foundations are provided for the following purposes
1) To distribute the total load coming on the structure
on large area.
2) To support the structure
3) To give enough stability to the structures against
various distributing forces such as wind, rain etc.
4) To prepare a level surface for concreting and masonry
work.

Site investigation:
The general inspection of site of work serves as a good for determine the type of
foundation, to be adopted for the proposed work and in addition, it helps in getting the
data w.r.to the following items.
i) Behavior of ground due to variations in depth of water table
ii) Disposal of storm water at site
iii) Nature of soil by visual examination
iv) Movement of ground due to any reason etc.

2
 20-11-2023

Capacity of soil to support the

load applied to the ground

Light weight Drop testing Equipment for

Plate load test Bearing Capacity
(Source:
https://www.sciencedirect.com/topics/en
gineering/plate-load-test)

3
 20-11-2023

Types of foundations:
Depending upon their nature and depth, foundations have
been categorized as follows
(i) Open foundations or shallow foundations
(ii) Deep foundations

Open foundations or shallow foundations:

• This is most common type of foundation and can be laid using open excavation by
allowing natural slopes on all sides. This type of foundation is practicable for a
depth of about 5m and is normally convenient above the water table.
• The base of the structure is enlarged or spread to provide individual support. Since
the spread foundations are constructed in open excavations, therefore they are
termed as open foundations. This type of foundation is provided for structure of
moderate height built on sufficiently firm dry ground.

4
 20-11-2023

The various types of spread footings are:

1. Wall footing
2. Isolated footing
3. Combined footing
4. Inverted arch footing
5. Continuous footing
6. Cantilever footing
7. Grillage footing

Wall Footing: These footings can be either simple or stepped. The base course of these footings
can be concrete or entirely of one material simple footing are used for light structures. They
have only one projection beyond the width of the wall.

5
 20-11-2023

Isolated Footings: These are used to support undivided columns. They can be of stepped
type or have projections in the concrete base. In case of heavy loaded columns steel
reinforcement is provided in both directions in concrete with 15cm offsets

Types of Isolated Footings

6
 20-11-2023

Combined Footing: A combined footing supports two or more

columns in a row A Combined footing may be rectangular or
trapezoidal constructed with reinforced concrete. The location of
center of gravity of column loads and centroid of the footing
should coincide.

Types Combined Footing

7
 20-11-2023

Inverted Arch Footing: This type of construction is used on soft

soils to reduce the depth of foundation loads above an opening
are transmitted from supporting walls through inverted arches to
the soil. In this type the end columns must be stable enough to
resist the outward pressure caused by arch actions.

Continuous Footing: In this type of footing a single continuous

R.C slab is produced as foundation of two or three or more
columns in a row. This type of footing is suitable at locations
liable to earthquake activities. This also prevents differential
settlement in the structure. In order to have better stability a
deeper beam is constructed in between the columns

8
 20-11-2023

Combined Footing

Strap or cantilever footing: Strap footing consists of two or

more individual footings connected by a beam called strap or
cantilever footing or pump handle foundation. This type of
foundation may be used where the distance between the columns
is so great that combined trapezoidal footing becomes quite
narrow with high bending moments strap or cantilever footing

9
 20-11-2023

Grillage footing : This type of footing is used to transmit heavy

loads from steel columns to foundation soils having low bearing
power. This type of foundation avoids deep excavation and
provides necessary area at the base to reduce the intensity of
pressure of the foundation soil is not stiff and there is a
plenty of water with spring, the sides are protected by sharing.

10
 20-11-2023

Raft Foundation: A raft or mat is a combined footing that covers the entire area beneath
a structure and supports all the columns. When the allowable soil pressure is low or the
structure loads are heavy the use of spread footings would cover more than one half of
the area and it may be prove more economical to use raft foundation. There are also
used where the soil mass contains compressible lenses so that the differential
settlement would be difficult to control usually when the hard soil is not available within
1.5 to 2.5m, a raft foundation is adopted. The raft is composed of reinforced. Concrete
beam with relatively thin slab underneath

Raft /Mat Foundation

Deep foundations:

These foundations carry loads from a structure through weak

compressible soil or fills onto the stronger and less compressible
soils or rocks at depth. These foundations are in general used as
basements, buoyancy rafts, coissions, cylinders, shaft and piles.

11
 20-11-2023

Deep foundations:

Deep foundations:

12
 20-11-2023

Friction file & Bearing Pile

Under-reamed Piles

Requirements of a good foundation:

13
 20-11-2023

Causes of failure of good foundation:

14
20-11-2023

15