A PROJECT REPORT ON

TRANSFORMERS
FOR
AISSCE 2022 EXAMINATION
SUBMITTED BY
S.P. TARUNYAA
HALL TICKET NUMBER:______________
Under the guidance of : MR. CHETHAN,MRS. SITA
MAHALAKSHMI, MR.IMTIYAZ and MR. MARVIN

DEPARTMENT OF PHYSICS
SRI CHAITANYA TECHNO SCHOOL
Acknowledgement
 I would like to thank the institution for giving the
opportunity to encase and display our talent through this
project

I would like to thank my Physics teachers Mr. Chetan,

Mrs Sita Mahalakshmi, Mr. Imtiyaz and Mr. Marvin for
having the patience to guide me at every step in the
project

I am also grateful to the CBSE board for giving this

opportunity to do a challenging project in which we were
very engrossed

I would also like to thank my parents and friends who

helped me in getting the right information for this project
 INDEX

 INTRODUCTION ………….. 1
 TYPES ……………………… 2-5
 PRINCIPLE…………………. 6-7
 PARTS OF SINGLE FACE
TRANSFORMER………….. 8-10
 EFFICIENCY……………….. 10
 APPLICATIONS…………… 11
 CONCLUSION…………….. 11
 BIBLIOGRAPHY………….. 12
 INTRODUCTION
The transformer in the simplest way can be described as a
thing that steps up or steps down voltage.
In a step-up transformer, the output voltage is increased
and in a step-down transformer, the output voltage is
decreased.
The step-up transformer will decrease the output current
and the step-down transformer will increase the output
current for keeping the input and the output power of the
system equal.
The transformer is basically a voltage control device that is
u4sed widely in the distribution and transmission of
alternating current power.
The idea of a transformer was first discussed by Michael
Faraday in the year 1831 and was carried forward by many
other prominent scientific scholars.
However, the general purpose of using transformers was
to maintain a balance between the electricity that was
generated at very high voltages and consumption which
was done at very low voltages.

1
A transformer is a device used in the power transmission
of electric energy. The transmission current is AC. It is
commonly used to increase or decrease the supply voltage
without a change in the frequency of AC between circuits.
The transformer works on basic principles
of electromagnetic induction.

Transformers are used in various fields like power

generation grid, distribution sector, transmission and
electric energy consumption. There are various types of
transformers which are classified based on the following
factors;
 Working voltage range.
 The medium used in the core.
 Winding arrangement.
 Installation location.

2
Commonly used transformer type, depending upon
voltage they are classified as:
 Step-up Transformer: They are used between the
power generator and the power grid. The secondary
output voltage is higher than the input voltage.

 Step down Transformer: These transformers are

used to convert high voltage primary supply to low
voltage secondary output.

In a transformer, we will find different types of cores that

are used.
 Air core Transformer: The flux linkage between
primary and secondary winding is through the air.
The coil or windings wound on the non-magnetic
strip.
3
 Iron core Transformer: Windings are wound on
multiple iron plates stacked together, which provides
a perfect linkage path to generate flux.

 Autotransformer: It will have only one winding

wound over a laminated core. The primary and
secondary share the same coil. Auto also means “self”
in language Greek.

 Power Transformer: It is used at power generation

stations as they are suitable for high voltage
application
 Distribution Transformer: Mostly used at
distribution lanes for domestic purposes. They are
designed for carrying low voltages. It is very easy to
install and characterized by low magnetic losses.

4
 Measurement Transformers: These are further
classified. They are mainly used for measuring
voltage, current, power.

 Protection Transformers: They are used for

component protection purposes. In circuits, some
components must be protected from voltage
fluctuation etc. Protection transformers ensure
component protection.

5
The transformer works on the principle of Faraday’s
law of electromagnetic induction and mutual induction.
There are usually two coils primary coil and secondary coil
on the transformer core. The core laminations are joined
in the form of strips. The two coils have high mutual
inductance. When an alternating current pass through the
primary coil it creates a varying magnetic flux. As per
faraday’s law of electromagnetic induction, this change in
magnetic flux induces an emf (electromotive force) in the
secondary coil which is linked to the core having a primary
coil. This is mutual induction.

6
Overall, a transformer carries the below operations:
1. Transfer of electrical energy from circuit to
another
2. Transfer of electrical power through
electromagnetic induction
3. Electric power transfer without any change in
frequency
4. Two circuits are linked with mutual
induction

7
The major parts of a single-phase transformer consist of;
1. Core
The core acts as a support to the winding in the
transformer. It also provides a low reluctance path to the
flow of magnetic flux. The winding is wound on the core
as shown in the picture. It is made up of a laminated soft
iron core in order to reduce the losses in a transformer.
The factors such as operating voltage, current, power etc
decide core composition. The core diameter is directly
proportional to copper losses and inversely proportional
to iron losses.

8
2. Windings
Windings are the set of copper wires wound over the
transformer core. Copper wires are used due to:

The high conductivity of copper minimizes the loss in a

transformer because when the conductivity increases,
resistance to current flow decreases.
 The high ductility of copper is the property of metals
that allows it to be made into very thin wires.

There are mainly two types of windings. Primary windings

and secondary windings.
 Primary winding: The set of turns of windings to
which supply current is fed.
 Secondary winding: The set of turns of winding from

which output is taken.

 The primary and secondary windings are insulated

from each other using insulation coating agents.

3. Insulation Agents
Insulation is necessary for transformers to separate
windings from each other and to avoid short circuit. This
facilitates mutual induction. Insulation agents have an
influence on the durability and the stability of a
transformer.
9
Following are used as an insulation medium in a
transformer:
 Insulating oil
 Insulating tape
 Insulating paper

Comparing system output with input will confirm tra

nsformer efficiency. The system is called better when its
efficiency is high.

Efficiency(η)=Output power / Inputpower×100

Efficiency(η)=PoutPout+Ploses×100
Efficiency(η)=V2I2cosθV2I2cosθ+Pc+Pcm×100

Where P = P / P = P

η(fullload)=VAcosθVAcosθ+Pc+Pcm×100
η(loadn)=nVAcosθnVAcosθ+Pc+n2Pcm×100

10
  The transformer transmits electrical energy through
wise over long distances.
 Transformers with multiple secondary’s are used
in radio and TV recerivers which require
several different voltages.


 Transformers are used as voltage regulators.

Conclusion
Elecric transformers are passive, electric machine that use
magnetic flux to induce an electro motive force.
Transformers are also used to step up or step down
voltages between electrical systems.

11
 BIBLIOGRAPHY

 Physics NCERT class 12 textbook

 www.google.com
 https://byjus.com/jee/transformer/

12