SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

TECHNICAL SPECIFICATIONS OF THREE PHASE 11/0.433-0.250KV, STAR 1 (LEVEL-2),

16KVA TO 500KVA, 10 KVA NON STAR RATED AND 5KVA SINGLE PHASE 11/
0.250KV, NON STAR RATED (LEVEL-2) WITH CRGO/ AMORPHOUS CORE.

1.0 SCOPE:
As per the Electrical Transformer (Quality Control) Order, 2014, it is mandatory
that No Electrical Transformers shall be manufacture or store for sale, sell or
distribute which do not confirm to the specified standard and do not bear standard
Mark of the Bureau. Moreover, as per the Guidelines of Bureau of Energy
Efficiency (BEE), labeling of distribution transformer is mandatory & cannot be sold
in the market without star label. Accordingly, the bidder shall have to submit valid
BIS license of the quoted item or higher as per approved scheme of BIS and star
rating certificate from BEE for 16 KVA to 500 KVA Transformers.

This specification covers, engineering, manufacture, assembly, stage testing,

and inspection and testing before supply and delivery at site of mineral oil-
immersed, natural air-cooled, outdoor type, double-wound 3 phase
11/0.433 -0.250 KV Distribution Transformers for outdoor use in power
distribution systems with nominal system voltagesof following types and
ratings:
• Three Phase ratings lower than 63 KVA both non-sealed type and sealed
type. (REF: IS 1180 PART-1 2014, 3.2&3.3).
• Three phase ratings higher than and including63 KVA,non-sealed type.
(REF: IS 1180 PART-1 2014, 3.2&16).
• Single phase ratings 5 KVA sealed type.
1.1 It is not the intent to specify completely herein all the details of the design
and construction of equipment. However the equipment shall conform in all
respects to high standards of engineering, design and workmanship and
shall be capable of performing in continuous commercial operation up to
the Bidder’s guarantee, in a manner acceptable to the purchaser, who will
interpret the meanings of drawings and specification and shall have the
power to reject/accept any work or material which, in his judgment is there
or not in accordance therewith. The offered equipment shall be complete
with all components necessary for their effective and trouble free operation.
Such, components shall be deemed to be within the scope of Bidder’s supply
irrespective of whether those are specifically brought out in this
specification and / or the commercial order or not.
1.2 The transformer and accessories shall be designed to facilitate operation,
inspection, maintenance and repairs. The design shall incorporate every
precaution and provision for the safety of equipment as well as staff
Signature of Tenderer Company’s Round Seal Date Place
Page 1 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

engaged in operation and maintenance of equipment.

1.3 All outdoor apparatus, including bushing insulators with their mountings,
shall be designed so as to avoid any accumulation of water.
1.4 STANDARD RATINGS:
The Standard Ratings shall be 5 KVA, 10 KVA,16KVA, 25 KVA, 63 KVA, 100
KVA, 200 KVA and 500 KVA.

2.0 STANDARDS:
2.1 The materials shall conform in all respects to the relevant Indian /
International Standard Specification, with latest amendments thereof, some
of them are listed below:
Indian Standard Title International &
Internationally
recognized
standard
ISS – 1180 / Part-I/ 2014 Outdoor/Indoor type Oil immersed
with latest amendments distribution Transformer upto and including
2500 kVA, 33KV Specifications Mineral Oil
Immersed
ISS - 16585:2016 Magnetic materials - specifications for individual
materials - Fe based amorphous strip delivered in
the semi processed state
5484 Specifications for Aluminum wire rods ASTM B-233
649 Testing of Steel sheet and strips for magnetic
circuits
191: 2007 Copper
335 : 1993 New insulating oils BS 148, D-1473,
D-1533- 1934
IEC Pub 296-
1969
554 : 1999 Pipe threads where pressure-tight joints are
made on the threads — Dimensions,
tolerances and designation
1576 : 1992 Solid pressboard for electrical purpose IEC 641
1608 : 2005 Mechanical testing of metals — Tensile
testing
1747 : 1972 Nitrogen
1885 (Part 38) :1993 Electro technical vocabulary: Part 38 Power
transformers and reactors
1897 : 2008 Copper strip for electrical purpose
2026 Power transformers : IEC 76
(Part 1) : 2011 General
(Part 2) : 2010 Temperature rise
(Part 3) : 2009 Insulation levels, dielectric tests and external
Signature of Tenderer Company’s Round Seal Date Place
Page 2 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Indian Standard Title International &

Internationally
recognized
standard
clearances in air
(Part 5) : 2011 Ability to withstand short circuit
(Part 8) : 2009 Application guide
(Part 10) : 2009 Determination of sound levels
2099 : 1986 Bushings for alternative voltages above
1000 volts
3024 : 2006 Grain oriented electrical steel sheets and
strips
3347 Dimensions for porcelain transformer DIN 42531,23,3
bushings for use in lightly polluted
atmospheres
(Part 1/Sec 1) : 1979 Up to and including 1 kV, Section 1 Porcelain
parts
(Part 1/Sec 2) : 1979 Up to and including 1 kV, Section 2 Metal
parts
(Part 2/Sec 1) : 1979 3.6 kV Bushings, Section 1 Porcelain parts
(Part 2/Sec 2) : 1979 3.6 kV Bushings, Section 2 Metal parts
(Part 3/Sec 1) : 1988 17.5 kV Bushings, Section 1 Porcelain parts
(Part 3/Sec 2) : 1988 17.5 kV Bushings, Section 2 Metal parts
8603:2008 Dimensions for porcelain transformer
bushings for use in heavily polluted
atmospheres,12/17.5 KV,24 KV and 36 KV
ISS 5/1961 Specification for colors for ready mixed
paints.
ISS- 6600/1972 Guide for loading of oil Immersed IEC 76
Transformers
ISS-10028 Installation, Maintenance of Transformers
ISS-4257 Dimension for clamping arrangement for
bushings (for porcelain and metal
parts)
ISS- 6160 Rectangular conductors for electrical machine
ISS- 3401 Silica gel
ISS-1866 Code of practice for maintenance &
supervision of Mineral insulating oil in
equipment
3639 : 1966 Fittings and accessories for power
transformers
4253 (Part 2) : 2008 Cork composition sheet: Part 2 Cork and
rubber
6162 Paper-covered aluminum conductors
Signature of Tenderer Company’s Round Seal Date Place
Page 3 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Indian Standard Title International &

Internationally
recognized
standard
(Part 1) : 1971 Round conductors
(Part 2) : 1971 Rectangular conductors
7404 (Part1) : 1991 Paper covered copper conductors: Part 1
Round conductors
7421 : 1988 Porcelain bushings for alternating voltages up
to and including 1 000 V
8999 : 2003 Pipe threads where pressure tight joints are
made on the threads — Verification by means
of limit gauges
9335(Part 1) : 1979 Cellulosic papers for electrical purposes: IEC 554
Definitions and general requirements
(Part 2) : 1998 Methods of test
(Part 3/Sec 1) : Specifications for individual materials,
1984 Section 1 General purposes electrical paper
(Part 3/ Sec 3) :1984 Specifications for individual materials, Section
3 Crepe paper
(Part 3/ Sec 5) : 1985 Specifications for individual materials, Section
5 Special papers
11149 : 1984 Specification for rubber gaskets
12444 : 1988 Continuously cast and rolled ASTM B-49
electrolytic copper wire rods for electrical
Conductors
13730 Specification for particular types of winding
wires:
(Part 0/ Sec 1) : 2012 General requirements Section 1, Enamelled
round copper wire
(Part 0/ Sec 2) : 2011 General requirements Section 2, Enamelled
rectangular copper wire
(Part 0/ Sec 3) : 2012 General requirements Section 3, Enamelled
round aluminium wire
(Part 17) : 1996 Polyvinyl acetalenamelled rectangular
copper wire, Class 105
(Part 27) : 1996 Paper covered rectangular copper wire
IS/IEC 60947- Low voltage switchgear and controlgear -
2:2003(Part:2) Circuit breakers
16081 : 2013 Insulating liquids — Specification for unused
synthetic organic esters for electrical
purposes
IS - 5561 Electrical power connector

Signature of Tenderer Company’s Round Seal Date Place

Page 4 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Indian Standard Title International &

Internationally
recognized
standard
IS - 6103 Testing of specific resistance of electrical
insulating liquids
IS - 6262 Method of test for power factor and dielectric
constant of electrical insulating liquids
IS - 6792 Determination of electrical strength of
insulating oil

Material conforming to other internationally accepted standards, which

ensure equal or higher quality than the standards mentioned above, would
also be acceptable. In case the Bidders who wish to offer material
conforming to the other standards, salient points of difference between the
standards adopted and the specific standards shall be clearly brought out in
relevant schedule. Four copies of such standards with authentic English
translations shall be furnished along with the offer.

3.0 SYSTEM DETAILS:

The distribution transformers shall be installed outdoor locations along 11
kV distribution networks, which consist of underground/ overhead
networks. The HV winding shall be connected with HT SFU/OCB/VCB/SF6 CB
of the ring main unit/ DO Fuse through 11kV (E) XLPE/PILC/AB cable/ bare
conductor. LV winding shall be connected to LV distribution box/switch type
fuse section pillar through 1.1 kV Single core 300 mm2 or suitable size
Aluminum conductor Cable.
The transformers shall be suitable for outdoor installation with 3 phase 50
Hz, 11 KV systems in which the neutral is effectively earthed and they should
be suitable for service under fluctuations in supply voltage up to plus 12.5%
to minus 12.5%.
3.1 SERVICE CONDITIONS:
The Distribution Transformers to be supplied against this Specification shall
be suitable for satisfactory continuous operation under the following
climatic conditions as per IS 2026 (Part - I) Latest Revision.
Sr. Parameters Values
No
1. Location At various locations in Gujarat
2. Max ambient air temperature (Degree C) 50
3. Min. ambient air temperature (Degree C) 0
4. Max average daily ambient air 45
temperature (Degree C)

Signature of Tenderer Company’s Round Seal Date Place

Page 5 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

5. Max. yearly weighed average ambient 40

temperature (Degree C)
6. Max. altitude above mean sea level 1000
(meter)
7. Maximum relative humidity (%age) 0 to 100%
8. Average thunder storms (days/ Annum) 15
9. Average rainy days (days/ Annum) 90
10. Average annual rain fall (mili meter) 800/ 900 mm
11. Number of months of tropical monsoon 3 Months
(months)
The equipment shall be for use in moderately hot and humid tropical
climate, conducive to rust and fungus growth.

Signature of Tenderer Company’s Round Seal Date Place

Page 6 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

4.0 PRINCIPAL PARAMETERS:

Sl. Item Specification

No.
1. Continuous rated 5 KVA 10 KVA 16 KVA 25 KVA 63 KVA 100 KVA 200 KVA 500 KVA
capacity
2. System voltage (max.) 12 kV (Line 12 kV 12 kV 12 kV 12 kV 12 kV 12 kV 12 kV
to Line)
3. Rated voltage HV 11 kV 11 kV 11 kV 11 kV 11 kV 11 kV 11 kV 11 kV
4. Rated voltage LV 250 V 433-250 V 433-250 V 433-250 V 433-250 V 433-250 V 433-250 433-250 V
V
5. Line current HV 0.454 A 0.525 A 0.84 A 1.31 A 3.306 A 5.25 A 10.50 A 26.25 A

6. Line current LV 20.0 A 13.3 A 21.33 A 33.33 A 84.0 A 133.0 A 266.0 A 665.0 A

7. Frequency 50 c/s +/- 50 c/s +/- 50 c/s +/- 50 c/s +/- 50 c/s +/- 50 c/s +/- 50 c/s +/- 50 c/s +/-
5% 5% 5% 5% 5% 5% 5% 5%

8. No. of Phases Single Three Three Three Three Three Three Three

9. Connection HV Single Delta Delta Delta Delta Delta Delta Delta

10. Connection LV Individual Star Star Star Star Star Star Star
(Neutral (Neutral (Neutral (Neutral (Neutral (Neutral (Neutral
brought brought brought brought brought brought brought
out) out) out) out) out) out) out)
11. Vector group -- Dyn-11 Dyn-11 Dyn-11 Dyn-11 Dyn-11 Dyn-11 Dyn-11
12. Type of cooling ONAN ONAN ONAN ONAN ONAN ONAN ONAN ONAN

Signature of Tenderer Company’s Round Seal Date Place

Page 7 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Sl. Item Specification

No.
13. Tap changing Not Not Not Not Not Not -7.5 % to -7.5 % to
arrangement applicable applicable applicable applicable applicable applicable +10% in +10% in
steps of steps of 2.5
2.5 % %
14. Noise level at rated 48db 48 db 48 db 48 db 51db 51db 55 db 56 db
voltage and frequency
15. Permissible temperature
rise over ambient
i) Of top oil measured
by thermometer 30Deg.C 35 Deg.C 35 Deg.C 35 Deg.C 35 Deg.C 35 Deg.C 35 Deg.C 35Deg.C
ii) Of winding
measuredby resistance 35Deg.C 40 Deg.C 40 Deg.C 40 Deg.C 40 Deg.C 40 Deg.C 40 Deg.C 40Deg.C
16 Minimum clearances in air of bushing terminals with connectors fitted in mm.
HV Phase to Phase 255 255 255 255 255 255 255 255
HV Phase to Earth 205 205 205 205 205 205 205 205
LV Phase to Phase -- 75 75 75 75 75 75 75
LV Phase/ Neutral to 75 55 55 55 55 55 55 55
Earth
17 Basic Insulation Level 95 KV 95 KV 95 KV 95 KV 95 KV 95 KV 95 KV 95 KV
(Minimum)

Signature of Tenderer Company’s Round Seal Date Place

Page 8 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

5.0 TECHNICAL REQUIREMENTS :

5.1 CORE:
A. CRGO:
i. Transformer core shall be stacked core type, shell type or with wound core
construction using new and high quality CRGO core with heat resistant
insulating coating. The core shall be of NEW/Fresh high grade cold rolled
grain oriented annealed lamination core having low loss and good grain
properties, coated with hot oil proof insulation, bolted together and to the
frames firmly to prevent vibration or noise. The complete design of core
must ensure permanency of the core losses with continuous working of the
transformers. The core shall be stress relieved by annealing under inert
atmosphere if required. The complete design of core must ensure
permanency of the core loss with continuous working of the transformers.
The value of the maximum flux density allowed in the design and grade of
lamination used shall be clearly stated in the offer.
ii. CORE CLAMPING :
1. MS channel shall be used on top and bottom.
2. Core Channel on LV side to be reinforced at equidistance, if holes /
cutting is done for LT lead in order to avoid bending of channel.
3. MS Channels shall be painted with hot oil-resistant paint.
4. The transformers core shall be suitable for over fluxing (due to
combined effect of voltage and frequency) up to 112.5% without
injurious heating at full load conditions and shall not get saturated. The
Bidder shall furnish necessary design data in support of this situation.
5. The nominal flux density in any part of the core shall not exceed 1.69
Tesla at 100% rated voltage and frequency and the maximum flux
density in any part of the core and yoke at rated voltage and frequency
shall be such that the flux density with 112.5 % combined voltage and
frequency variation from rated voltage and frequency shall not exceed
1.9Tesla. (REF IS 1180 PART-1 2014 6.9.1&7.9.1)
NOTE: The design calculations in support of flux density shall be furnished by
the manufacturer.
6. No load current shall not exceed the below mentioned percentage of
full load current by energizing the transformer on secondary side.
Particulars Up to Above
200KVA 200KVA

i. At rated voltage and frequency on the secondary. 3% 2%

ii. At voltage by 112.5% of rated voltage but at rated frequency. 6% 5%

7. Test for magnetic balance by connecting the LV phase by phase to rated

phase voltage and measurement of un, vn, wn voltage will be carried

Signature of Tenderer Company’s Round Seal Date Place

Page 9 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

out.
8. Clamping and Tie-rods shall be made from HT Bright Bars steel & shall
be painted with hot oil resistant paint.(IS 1180 table 12)

B. AMORPHOUS :
i. The core shall be high quality Amorphous ribbons having very low loss
formed into wound cores of rectangular shape, bolted together to the
frames firmly to prevent vibration or noise. The complete design of core
must ensure permanency of the core loss with continuous working of the
transformers. The value of the flux density allowed in the design shall be
clearly stated in the offer. Curve showing the properties of the metal shall
be attached with the offer.

ii.CORE CLAMPING FOR AMORPHOUS METAL TRANSFORMERS :

1. Core clamping shall be with top and bottom U-shaped core clamps
made of sheet steel clamped HT steel tie rods for efficient clamping.
2. MS core clamps and MS rods shall be painted with hot oil-resistant
paint.
3. HT Steel rods shall be used as tie rods.
4. Suitable provision shall be made in the bottom core clamp / bottom
plate of the transformer to arrest movement of the active part.The
core/coil assembly shall be securely held in position to avoid any
movement under short circuit conditions.
5. The transformers core shall be suitable for over fluxing (due to
combined effect of voltage and frequency) up to 112.5% without
injurious heating at full load conditions and shall not get saturated. The
Bidder shall furnish necessary design data in support of this
situation.(REF IS 1180 PART-1 2014 6.9.1&7.9.1)
6. No load current shall not exceed 2% of full load current and will be
measured by energizing the transformer at rated voltage and frequency
on the secondary. Increase of voltage by 12.5% shall not increase the
no load current by Max. 5% of full load current.
7. Test for magnetic balance by connecting the LV phase by phase to rated
phase voltage and measurement of un, vn, wn voltage will be carried
out.
8. Clamping and Tie-rods shall be made from HT Bright Bars steel & shall
be painted with hot oil resistant paint. (IS 1180 table 12)
5.2 WINDINGS:
Copper conductor shall be used for 11 KV /500 KVA and 5 KVA
Transformers, while Aluminum conductor shall be used for other capacities
of Transformers.
(A) MATERIALS:
Double paper covered aluminum/ Electrolytic Copper conductor or class H
Super enamel cover aluminum/ Electrolytic Copper conductor shall be used
Signature of Tenderer Company’s Round Seal Date Place
Page 10 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

for 11 KV class Transformers. A mix of Electrolytic copper & aluminum

conductors for HV & LV winding will not be permitted.
(B) CURRENT DENSITY (MAXIMUM):
ELECTROLYTIC COPPER CONDUCTOR: Shall not be more than 2.5 A/sq.mm.
ALUMINUM CONDUCTOR: Shall not be more than 1.60 A/sq.mm.
(However, +5% tolerances for LV winding are permissible).
NOTE:
1. LV winding shall be in form of even layers so that the neutral formation
will be at top.
2. The winding shall be of one or more rectangular conductors insulated
from each other to reduce eddy current losses. The tolerances on the
size of the conductor shall be as per IS-6160, specification for
rectangular conductors. If the active axial length of the coil is more than
350 mm, an axial duct, of 4 mm is provided between the LV coil layers.
The materials used for providing duct shall be non-compressible
material such as treated wood permali, etc. Any joints in the HV/LV
winding shall not be allowed.
3. Dimensional tolerances for winding coils shall be within limits as
specified in GTP.

(C) INTERNAL INSULATIONS AND CLEARANCES:

1. Insulating material: Electrical grade insulating craft paper of
Triveni/Ballarpur/Cauvery or equivalent make subject to approval of
the purchaser shall be used. Similarly Press Board of Senapathy,
Whitelay or Raman make or equivalent subject to the approval of
the purchaser shall be used. Perma wood or Haldi wood blocks shall
be used for top and bottom yoke insulation.
2. All spacers, axial wedges / runners used in windings shall be made of
pre-compressed Pressboard−solid, conforming to type B 3.1 of IEC
641-3-2. In case of cross-over coil winding of HV all spacers shall be
properly sheared and dovetail punched to ensure proper locking. All
axial wedges / runners shall be properly milled to dovetail shape so
that they pass through the designed spacers freely. Insulation
shearing, cutting, milling and punching operations shall be carried
out in such a way, that there should not be any burr and dimensional
variations.
3. Transformer rating 200KVA and above, an axial duct of 3 mm is to be
provided if the radial thickness of coils is more than 50 mm and/or
the axial length of individual coil is more than 80mm. The radial
duct shall be adequate for free circulation of oil as well as to
withstand voltage between adjacent coils. The inter – layer insulation
shall be of Nomex / Epoxy dotted Kraft paper or a minimum 4 layers
of 2 mil (0.05mm) paper of approved manufactures.
4. (a) Proper bonding of inter layer insulation with the conductor shall
Signature of Tenderer Company’s Round Seal Date Place
Page 11 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

be ensured.
(b)Inter layer insulation shall be Epoxy dotted Kraft Paper.
Test for bonding strength shall be conducted.
5. Internal Clearances& Number of HV/LV coils :

For Both Stack/Wound Core:

5 10 16 25 63 100 200 500

Parameters KVA KVA KVA KVA KVA KVA KVA KVA
Minimum Radial clearance of 3.5 3.5 3.5 3.5 3.5 4 4 4
LV Coil to Core in mm
Minimum radial clearance 11 11 11 11 11 11 11 11
between LV coil to HV coil in
mm
Phase to phase clearance in N.A. 10 10 10 10 10 10 10
mm between HV conductors
with a provision of minimum
of 2 x 1 mm press board to
cover the tie rods.
Minimum electrical 30 30 30 30 30 30 30 30
clearance between inside
surface of the Tank and
outside edge of the winding
in mm
End Insulation, Coil end to 25 25 25 25 25 25 25 25
Earth in mm
No. of Coils LV per Phase 1 1 1 1 1 1 1 1
Minimum No. of HV Coils up 1 4 4 4 4 4 4 4
to 500 KVA (Cross over
winding) – for Stack core
- Do – for Wound core 1 1 1 1 1 1 1 1
Minimum No. of axial 6 6 6 6 6 8 8 8
wedges between LV and HV
winding equi -spaced around

5.2.1 TAPS:

a) No tapping shall be provided for transformers up to 100 KVA rating.

b) For ratings above 100 KVA, tapings shall be provided on the higher voltage
winding for variation of HV voltage within range of (-) 7.5% to +10% (For
200 KVA & 500KVA) in steps of 2.5%.
c) Tap changing shall be carried out by means of an externally operated self-
Position rotary switch (to be mounted on top plate) and when the
transformer is in de-energized condition. Switch position No.1 shall
Signature of Tenderer Company’s Round Seal Date Place
Page 12 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

correspond to the maximum plus tapping. Each tap change shall result in
variation of 2.5% in voltage. Provision shall be made for locking the taping
switch handle in position. Suitable aluminum anodized plate shall be fixed
for tap changing switch to know the position number of tap.

5.2.2 OIL :
The insulating oil shall comply with the requirements of IS 335. Use of recycled
oil is not acceptable. The specific resistance of the oil shall not be less than 35
X1012 ohm-cm at 27⁰C when tested as per IS 6103.
Oil shall be filtered and tested for break down voltage (BDV) and moisture
content before filling.
The oil shall be filled under vacuum of 250 Tor +/- 5 %.
The design and all materials and processes used in the manufacture of the
transformer, shall be such as to reduce to a minimum the risk of the
development of acidity in the oil.

5.2.3 LOSSES & LEBELLING:

The maximum allowable losses at rated voltage and rated frequency permitted at 75⁰C and
percentage impedance up to 500 KVA, 11/0.433 KV Transformers shall be as per Level-2 of
IS 1180 (Part 1) :2014 and Star rating plan as per latest BEE guidelines, whichever
applicable. However, rating wise total losses shall be limited to the values as under.

Losses of the Transformer should not exceed following values and for transformers having
tapings shall be guaranteed at maximum current tap and it should not exceed following
values.
LOSSES of LABELLED TRANSFORMERS IN WATTS

NON STAR NON BEE rated Star 1 (Level-2 as per IS 1180

RATED STAR (Part 1) :2014)
Item
(LEVEL-2) RATED Capacity in KVA
5 10 16 25 63 100 200 500
Maximum No Load
15 40 50 60 125 170 270 545
Losses
Maximum total losses
35 84 135 190 340 475 780 1510
at 50% loading
Maximum *total losses
95 240 440 635 1140 1650 2300 4300
at 100% loading

*Total Losses in watt at 100 % loading = No Load losses in watt + Full Load losses in watt at
75 Deg. C

Bids with higher losses than above specified values would be treated as non responsive.
While in case of tapped transformer, Bids with higher losses than above specified values at
maximum current tap, would be treated as non responsive.
However, the manufacturer can offer losses lower than above.

Signature of Tenderer Company’s Round Seal Date Place

Page 13 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

NOTE: -
Offer without BIS and BEE certification will be out rightly rejected without any
correspondence.

5.3 EVALUATION CRITERIA:

1 The Tender price bids will be evaluated on the basis of firm Price End Cost including GST
and Cess, if any for CRGO/ Amorphous Core Transformer.
2 Bidder can offer CRGO/ Amorphous core material but they have to specify clearly in their
offer and price bid must be submitted for respective core separately.
3 Bidder can also offer both CRGO as well as Amorphous core for same rating, but they
have to separately submit GTP for both core materials Transformers and they have to
submit on line price bid separately for both core material. Bidder has to clearly mention
offer quantity with core material in ANNEXURE-4.
4 Price matching will be carried out on the base of unit end cost including GST and cess, if
any.

5.4 PERCENTAGE IMPEDANCE:

Rating of Transformer in KVA Percentage Impedance at 750C

5 KVA 4.00 %
10 KVA to 100 KVA 4.50 %
200 KVA & 500 KVA 4.75%

% impedance shall be subject to tolerance specified in IS: 2026.

Bids not meeting the limits indicated above will be treated as non-responsive.

5.5 TEMPERATURE RISE:

The temperature rises over ambient shall not exceed the limits described
below (Total losses guaranteed offered in GTP shall have to be fed for
Temperature rise test)

Temperature Rise 5 KVA 10 to 500 KVA

Top oil temperature rise measured by 30 deg.C 35 deg.C
thermometer
Winding temperature rise measured by 35 deg.C 40 deg.C
resistance

Bids not meeting the above limits of temperature rise will be treated as non-
responsive.
5.6 PENALTY FOR NON PERFORMANCE:

A. During testing, if it is found that the actual measured losses are more than
the values quoted by the bidder, the purchaser will have right to exercise
Signature of Tenderer Company’s Round Seal Date Place
Page 14 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

one of the following options

Reject the complete lot OR Penalty shall be recovered from the bidder for
the excess losses per watt as under
a. Rs. 493.52 per Watt for No load loss.
b. Rs. 272.92 per Watt for Load loss.

B. Transformers with temperature rise and impedance beyond guaranteed

values:
i. If the temperature rise exceeds the guaranteed values in any sample of the
transformer during testing, purchaser reserves the right to reject the
available lot of the transformer.
ii. If the impedance values differ from the guaranteed values including
tolerance in any sample of the transformer during testing,purchaser
reserves the right to reject the available lot of the transformer.
iii. Purchaser also reserves the right to retain the rejected transformer and
take it into service until the supplier replaces it with a new transformer at
no extra cost. The delivery as per contract will be counted when the new
transformer as per specification is provided by the manufacture.
iv. Purchaser also reserves the right to utilize the rejected lot of transformers
with a penalty maximum up to 30% as per the clause of commercial terms
and condition.

C. TESTS AT SITE:
The purchaser reserves the right to conduct all tests on Transformer after
arrival at site and the manufacturer shall guarantee test certificate figures
under actual service conditions.
In order to ensure quality the acceptance test shall be carried out even
after installation of transformer within grantee period. If acceptance test
standards are not met during such field test, 5% penalty may be imposed
on all transformers supplied as per that proto type design.

5.7 TANK :
Transformer tank construction shall conform in all respect to clause 15 of IS
1180(Part-1):2014.The transformer tank can be with radiator fins/ rounded
or elliptical cooling tubes or made of corrugated panels.
A. FOR RECTANGULAR PLAIN TANK:
i. The transformer tank shall be of robust construction rectangular in shape
and shall be built up of tested MS sheets.
The tank shall be made of prime quality MS sheet of thickness stated below
with necessary stiffener to withstand the pressure built in during the
expansion of oil due to temperature rise.
The exterior of the transformer tank and other ferrous fitting shall be
thoroughly cleaned , scraped /sand blasted and given a priming coat and
Signature of Tenderer Company’s Round Seal Date Place
Page 15 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

two finishing coats of durable oil and weather resistant paint of dark
admiral grey conforming to color code No. 632 of IS-5/1961.
The internal clearance of tank shall be such that, it shall facilitate easy lifting
of core with coils from the tank without dismantling LV bushings.
ii. All joints of tank and fittings shall be oil tight and no bulging should occur
during service. The tank design shall be such that the core and windings
can be lifted freely. The tank plate shall be of such strength that the
complete transformers when filled with oil may be lifted bodily by means of
lifting lugs. Inside of tank shall be painted with Hot oil resistive paint.
iii. Manufacturer should carry out all welding operations as per the relevant
ASME standards and submit a copy of the welding procedure qualifications
and welder performance qualification certificates to the customer.
iv. Up to 200 KVA Transformers, the four walls of the rectangular tank shall be
made of Two “L” shaped sheets (without joints) fully welded at the corners
from inside and outside of the tank for withstanding a pressure of 80 kPa
for 30 minutes and vacuum of 250 mm of mercury for 30 Min.
(OR)
One “U” shaped bend sheet with straight plate and welded outside the tank
at 2 corners for withstanding a pressure of 80 kPa for 30 minutes”. While
500 KVA Transformer withstanding a pressure of 80 kPa for 30 minutes and
vacuum of 500 mm of mercury for 30 Min. There should be no air leakage
at any point.
Under operating conditions the pressure generated inside the tank should
not exceed 0.4 kg/ sq. cm positive or negative. There must be sufficient
space from the core to the top cover to take care of oil expansion. The
space above oil level in the tank shall be filled with dry air or nitrogen
conforming to commercial grade of IS 1747.
v. Up to 500 KVA Transformers, the permanent deflection of flat plates, after
pressure/ vacuum has been released, shall not exceed 5 mm up to 750 mm
length and 6.5 mm up to 1250 mm length.
vi. For single phase transformers, minimum Oil level mark shall be embossed
inside the tank (at 250 C).
vii. The Single Phase transformer shall be provided with two mounting lugs
suitable for fixing the transformer to a single pole by means of 2 bolts of 20
mm diameter as per ANSI C 57.12.20-1988. The circular bottom plate edges
of the tank should be folded upward, for at least 25 mm, to have sufficient
overlap with vertical sidewall of the transformer.
viii. TANK SEALING for Single Phase:
The space on the top of the oil shall be filled with dry air or nitrogen. The
nitrogen plus oil volume inside the tank shall be such that even under
extreme operating conditions, the pressure generated inside the tank does
not exceed 0.4 kg/sq. cm positive or negative. The nitrogen shall conform to
commercial grade of the relevant standards.
ix. For single phase transformers, round tank shall withstand pressure of 100
Signature of Tenderer Company’s Round Seal Date Place
Page 16 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

kPa and a vacuum of 760 mm of mercury for 30 Min.

Nominal thickness of plate in mm

Rating
(tolerance applicable as per relevant IS )
For Top & Bottom
(11 kV) For sides (mm)
(mm)
5 KVA (Round Tank) 2.2 2.5
Rectangular Tank

5 kVA to 100 KVA 3.15 5.0

Above 100 KVA 4.5 6.0

x. Top cover of the transformer tank shall be slanting minimum 10 to 15 mm

towards HV Bushing so that entry of water can be avoided.
The radiators can be tube type or fin type or pressed steel type to achieve
the desired cooling to limit the specified temperature rise. The transformer
shall be capable of giving continuous rated output without exceeding the
specified temperature rise. Bidder shall submit the calculation sheet for
heat dissipation.
xi. Lifting lugs: 2 Nos. of lifting lugs are to be provided in Transformers below
100 KVA rating and 4 Nos. lifting lugs are to be provided in Transformers for
100 KVA and above rating transformers. Lifting lugs of MS plate 8 mm thick
(min) suitably reinforced by vertical supporting flat welded edgewise below
the lug on the side wall.
xii. Pulling lugs: 4 Nos. of welded heavy duty pulling lugs of MS plate 8 mm
thick (min) shall be provided to pull the transformer horizontally.
xiii. Top cover fixing bolts of Stainless Steel of size ½” dia. adequately spaced
not more than 80 mm pitch and 6 mm Neoprene bonded cork gaskets
conforming to type III as per IS 11149/ type-c as per IS 4253 (Part-2) shall be
placed between tank and cover.
xiv. The Stainless Steel bolts outside tank shall have 2 flat washers & one spring
washer.

B. FOR ELLIPTICAL TANK:

The Bidder may offer Elliptical tanks for 10 &16 KVA transformers, robust in
construction with adequate strength to withstand the pressure built in
during the expansion of oil due to temperature rise. The tank sheet shall be
electrically welded to impart proper mechanical strength and to plug
leakage of oil. All joints of tank and fittings shall be oil tight and no bulging
shall occur during service. The tank sheets shall be of such strength that the
complete transformer when filled with oil may be lifted by means of lifting
lugs provided. All the welding shall be continuous.

Signature of Tenderer Company’s Round Seal Date Place

Page 17 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

The elliptical tank constructed by two welding joints only, one is at bottom
cover and another is at the tank shell so that the leakages due to joints can
be reduced. The tank shall withstand a pressure of 80 kPa for 30 minutes and
vacuum of 250 mm of mercury for 30 Min and the permanent deflection
after pressure/ vacuum has been released, shall not exceed 5 mm.

C. FOR CORRUGATED TANK

1. The transformer tank shall be of robust construction corrugated in shape
and shall be built up of tested sheets.
2. The transformers with corrugation should be provided with proper safe
packing during transportation, so that tank shall be prevented from any
physical damage.
3. Corrugation panel shall be used for cooling. The transformer shall be
capable of giving continuous rated output without exceeding the specified
temperature rise. Bidder shall submit the calculation sheet in this regard.
4. Up to 200 KVA Transformers, the tank shall be design for a pressure of 25
kPa above atmosphere pressure, measured inside the tank for 30 minutes
and vacuum of 250 mm of mercury for 30 minutes. While for 500 KVA
transformers, the tank shall be design for a pressure of 25 kPa above
atmosphere pressure, measured inside the tank for 30 minutes and vacuum
of 500 mm of mercury for 30 minutes. There should be no air leakage at any
point.
5. The nominal thickness of corrugation panel sheet is 1.2 mm.
6. The tank thickness shall be as per Rectangular Plain Tank.
7. Vacuum test and pressure test are applicable as per type test mentioned in
this specification.
D. CONSERVATOR :
Transformers of rating 63 kVA and above with plain tank construction, the
provision of conservator is mandatory. For sealed type transformer with or
without inert gas cushion, conservator is not required.
For sealed transformer pressure relief valve shall be provided.PRV shall be of
35 kPa with Dia.12.5 mm. For 200 KVA & above rating transformers, PRV for
plain tank shall be of 70 kPa with Dia.1”. (All forged brass, stainless steel
components for use in extreme outdoor conditions)
When a conservator is provided, oil gauge and dehydrating breathing device
shall be fixed to the conservator which shall also be provided with a drain
plug and a filling hole (1¼" normal size thread) with cover. The capacity of a
conservator tank shall be designed to contain 10% of the total quantity of oil
and its contraction and expansion due to temperature variations. Normally
3% quantity of total oil will be contained in the conservator. In addition the
cover of main tank shall be provided with an air release plug to enable air
trapped within to be released, unless the conservator is so located as to
eliminate the possibility of air being trapped within the main tank.
Signature of Tenderer Company’s Round Seal Date Place
Page 18 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

The inside diameter of the pipe connecting the conservator to the main tank
should be within 30 to 50 mm and it should be projected into the
conservator so that its end is approximately 20 mm above the bottom of the
conservator so as to create a sump for collection of impurities. The
minimum oil level (corresponding to -5 deg C) should be above the sump
level.
E. DEHYDRATING BREATHER:
Breather shall be screwed type. It shall have die cast aluminum body &
further, inside container for silica gel shall be of tin sheet. Inverted U-shape
pipe shall be used for connection of breather. The dehydrating agent shall be
silica gel. The moisture absorption shall be indicated by a change in the
colour of the silica gel crystals which should be easily visible from a distance.
Volume of breather shall be suitable for 500g of silica gel conforming to IS
3401 for transformers upto 200 kVA and 1 kg for transformers above 200
kVA. The make and design of breather shall be subject to approval of
DISCOM, Gujarat.
Breather: Individual Breather shall be packed in a cotton bag shall be bound
with individual transformer in a clear visible position.

5.8 SURFACE PREPARATION & PAINTING

A. GENERAL :
1. All paints shall be applied in accordance with the paint manufacturer’s
recommendations. Particular attention shall be paid to the following:
i. Proper storage to avoid exposure as well as extremes of temperature.
ii. Surface preparation prior to painting.
iii. Mixing and thinning
iv. Application of paints and the recommended limit on time intervals
between coats.
v. Self life for storage
2. All paints, when applied in a normal full coat, shall be free from runs, sags,
wrinkles, patchiness, brush marks or other defects.
3. All primers shall be well marked into the surface, particularly in areas where
painting is evident, and the first priming coat shall be applied as soon as
possible after cleaning. The paint shall be applied by airless spray according
to manufacturer’s recommendations. However, wherever airless spray is
not possible, conventional spray be used with prior approval of purchaser.
4. The Supplier shall, prior to painting protect nameplates, lettering gauges,
sight glasses, light fittings and similar such items.

B. CLEANING AND SURFACE PREPARATION

i. After all machining, forming and welding has been completed, all steel work
surfaces shall be thoroughly cleaned of rust, scale, welding slag or spatter
and other contamination prior to any painting.
Signature of Tenderer Company’s Round Seal Date Place
Page 19 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

ii. Steel surfaces shall be prepared by shot blast cleaning (IS9954) to grade Sq.
2.5 of ISO 8501-1 or chemical cleaning by Seven Tank process including
phosphating of the appropriate quality (IS 3618).
iii. The pressure and volume of the compressed air supply for blast cleaning
shall meet the work requirements and shall be sufficiently free from all water
contamination to ensure that the cleaning process is not impaired.
iv. Chipping, scraping and steel wire brushing using manual or power driven
tools cannot remove firmly adherent mill-scale shall only be used where blast
cleaning is impractical. Manufacturer to explain such areas in his technical
offer clearly.
C. PROTECTIVE COATING
As soon as all items have been cleaned and within four hours of the
subsequent drying, they shall be given suitable anti-corrosion protection.

D. PAINT MATERIAL:
i. The color of the finishing coats shall be dark admiral gray conforming to No.
632 of IS-5 of 1961.
ii. Inside of tank shall be painted with oil resistance paint of colour shade
yellow/green. For external surfaces, one coat of thermosetting powder paint
shall be used.
iii. For highly polluted areas, chemical atmosphere or for places very near to the
sea coast, paint as above with one coat of high build Micaceous iron oxide
(MIO) as an intermediate coat may be used.
iv. To the maximum extent practicable the coat shall be applied as a continuous
film of uniform thickness and free of pores. Overspray, skips, runs, sags and
drips should be avoided. Each coat of paint shall be allowed to harden
before the next is applied.
v. Particular attention must be paid to full film thickness at edges.
vi. The requirements for the dry film thickness (DFT) of paint and the materials
to be used shall be as given below.
Sr. Paint Type Area to No. of Total Dry film
No be coats thickness (min.) in
painted microns
1. Thermo setting powder paint Outside 01 60
OR Liquid paint
a) Epoxy (Primer)
b) Polyurethane(finished coat)
2. Thermo setting powder paint Inside 01 30
OR
Liquid paint
Hot oil resistant paint of Inside 01 35
colour shade yellow/green

Signature of Tenderer Company’s Round Seal Date Place

Page 20 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Note : Supplier shall guarantee the painting performance requirement for a

period of not less than 5 years.

E. PAINTING PROCEDURE:
i. All painting shall be carried out in conformity with both Specification and
with the paint manufacturer’s recommendation. All paints in any one
particular system, whether shop or site applied, shall originate from one
paint manufacturer.
ii. Particular attention shall be paid to the manufacturer’s instructions on
storage, mixing, thinning and pot life. The paint shall only be applied in the
manner detailed by the manufacturer e.g. brush, roller, conventional or
airless spray and shall be applied under the manufacturer’s recommended
condition.
iii. All prepared steel surfaces should be primed before visible re-rusting occurs
or within 4 hours, whichever is sooner. Chemical treated steel surfaces shall
be primed as soon as the surface is dry and while the surface is still warm.
iv. Where the quality of film is impaired by excess film thickness (wrinkling, mud
cracking or general softness) the Supplier shall remove the unsatisfactory
paint coating and apply another. As a general rule, dry film thickness should
not exceed the specified minimum dry film thickens by more than 25%.
v. Paint applied to items that are not be painted shall be removed at Supplier’s
expense, leaving the surface clean, unstained and undamaged.

F. DAMAGED PAINTWORK:
i. Any damage occurring to painting of any part shall be made good to the
same standard of corrosion protection and appearance as that originally
employed, within guarantee/ warrantee period at free of cost.
ii. Any damaged paint work shall be made good as follows:
a) The damaged area, together with an area extending 25 mm around its
boundary, shall be cleaned down to bare metal.
b) A priming coat shall be immediately applied, followed by a full paint
finish equal to that originally applied and extending 50 mm around the
perimeter of the original damage.
c) The repainted surface shall present a smooth surface. This shall be
obtained by carefully chamfering the paint edges before and after
priming.
G. TESTSFOR PAINTED SURFACE:
i. The painted surface shall be tested for paint thickness.
ii. The painted surface shall pass the cross hatch adhesion test and impact test
as acceptance tests and Salt spray test and Hardness test as type test as per
the relevant ASTM standards.

5.9 BUSHINGS AND TERMINALS :

A. TRANSFORMER WITH BARE BUSHING OUTDOOR MOUNTING:
Signature of Tenderer Company’s Round Seal Date Place
Page 21 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

For 11 KV Transformers – 17.5 KV class bushings shall be used and further for
LV side, viz. 250/433 volts, 1KV terminal bushing shall be used. Bushing of the
same voltage class shall be interchangeable bushing with plain shed as per IS
3347. Bushings shall be mounted on top plate only.
OR
HT bushing should be kept in such a way that minimum air clearances should
be maintained by tilting the same.
Suitable insulating shrouds shall be provided on the HT bushing terminals.

The HV bushings shall have to be installed on top plate on turret, flange and
gaskets to prevent eventual entry of water. The turret height for HV bushing
should be minimum 25 to 30mm. In LV side bushing, turret of minimum 10
mm should be provided.

Dimensions of the bushings of the voltage class shall conform to the Standards
specified and dimension of clamping arrangement shall be as per IS 4257.
Bushing can be of porcelain material.

Note: Embossing on bushing showing the Manufacturer’s name,year of

manufacturing shall be clearly visible, even after fixing the same on
Transformer.

Bushings of Make mentioned in Schedule A or other makes having type tested

as per IS 2099 and approved by the GUVNL/PGVCL/MGVCL/DGVCL/UGVCL
shall only be used &are acceptable.

The cross section of the connecting rods on LV side shall be as per IS 3347
Part1/Sec 2 1979and shall be adequate for carrying the rated currents. On the
HV side the terminal rod shall have a diameter of not less than 12 mm of brass
up to 200 KVA as per IS 3347 Part3/Sec 2 1982and above200 KVA shall be of
Copper.

The bi-metallic connectors shall have to be fitted on HV/LV terminals having

capacity to withstand 1.5 times of rated HV/LV current of transformer.

Note : For 5 KVA Single Phase & 10 KVA, 16 KVA and 25 KVA, Three Phase
transformer having provision of MCCB, hence LV Bimetallic clamps are not
required.

HV AND LV TERMINALS:
The LV and HV bushing stems shall be provided with suitable terminal
connectors as per IS 5082 so as to connect the jumper without disturbing the
bushing stem. Terminal connectors shall be type tested as per IS 5561.
Signature of Tenderer Company’s Round Seal Date Place
Page 22 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Current density in HV and LV Terminals shall not exceed 1 Amp/sq.mm in case

of Brass terminals and 2 Amp/sq.mm in case of copper terminals.

B. INTERNAL CONNECTION:

1. HV WINDING:
i. In case of HV winding all jumpers from winding to bushing shall have cross
section double the winding conductor.
ii. Inter coil connection shall be done by brazing as per ASME, section-IX.
iii. In case of AL/CU winding Delta joint shall be with brazing only.
iv. Lead from Delta joint shall be connected to bushing rod by brazing only.
v. Current density in any of the conductor (in Delta connections also) shall
not exceed 1 Amp/sq.mm and 2Amp/sq.mm for aluminum conductor and
copper conductor respectively.
2. LV WINDING:
LV star point shall be formed of AL/CU flat of sufficient size and length. Lead
from winding shall be connected to the flat by brazing.
Firm connection of LV winding to bushing shall be made of adequate size of
“L” shape flat. Connection of LV coil lead to “L” shape flat shall be made by
brazing. The "L" Shape flat shall be of copper for copper winding &
Aluminum of Aluminum winding. “L” shape flat/lug shall be clamped to LV
bushing metal part by using nut, locknut and washer.

5.10 TANK BASE CHANNEL:

Two numbers of channels having following minimum size are to be provided.
Sr. Transformer capacity in KVA Minimum Size of base Channel in mm
No
1 5 KVA to 100 KVA 75 x 40 x 460 mm
2 200 KVA &500 KVA 100 x 50 mm

The transformers shall be suitable for loading as per IS: 6600 / 1972with
latest amendment if any.
The under base of all transformers shall be provided with holes to make them
suitable for fixing on a platform or plinth.

5.11 NAME PLATE &TERMINAL MARKINGS :

5.11.1 High voltage phase windings shall be marked both in the terminal
boards inside the tank and on the outside with capital letter 1U, 1V, 1W
and low voltage winding for the same phase marked by corresponding
letter 2u, 2v, 2w. The neutral point terminal shall be indicated by the
letter 2n. Neutral terminal to be brought out.

Signature of Tenderer Company’s Round Seal Date Place

Page 23 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

5.11.2 Each Transformer shall be provided with combined non-detachable

Name plate made of anodized aluminum/ stainless steel material
securely fixed on the outer body, easily accessible. The information of
Rating and terminal markings as per IS 1180 (Part-I) 2014, Clause No. 13
shall be engraved (punched) on combined name plate. The Transformer
shall be marked with the Standard Mark. Details of Guarantee Period
shall also be mentioned in combined Name Plate being a special
requirement of DISCOM.
5.11.3 On opposite side of the combined name plate, other plate made of
stainless steel material shall be welded on tank of Transformer. The
Transformer fication Number (TIN) shall be engraved (punched) on
plate & it shall be clearly visible. The Transformer Identification Number
(TIN) of minimum Nineteen digits/letters shall incorporate details of
Name of DISCOM, Trans. KVA rating, supplier name code, month & Year
of manufacturing, CPP tender no. and sr. no. given by supplier (Refer
Annexure II).

5.12 OTHER FITTINGS:

The following other fittings over and above standard fittings shall be
provided.
a. Earthing terminals with earthing symbol having minimum size 1⅟2” X ⅟2” with
lugs - 2 Nos.
b. HV bushings
3 nos. for 3 ph transformer
2 nos. for 1 ph transformer
c. LV bushings
4 nos. for 3 ph transformer
2 nos. for 1 ph transformer
d. Terminal connectors on the HV bushings
e. Terminal connectors on the LV bushings (above 25 KVA )
f. Thermometer pocket with cap - 1 no.
g. Oil filling hole (1.25 Inch, nominal size thread)/ with protection net / flat strip to
prevent oil theft
h. Stiffener angle 40x40x5 mm and vertical strip of 50x5 mm flat
i. Base channel having minimum size 75x40x460 mm for up to 100 KVA and 100
mm x 50 mm for 200 KVA & 500 KVA, with holes to make them suitable for
fixing on a platform or plinth.
j. 4 No. bi-directional rollers for transformers of 500 kVA.
k. Radiators: No. & length may be mentioned (as per heat dissipation
calculations)
l. Arcing horns for HV bushings
m. Breather, if applicable
n. Air release device (for non-sealed type transformers)
o. Pressure relief device valve (PRV) – 1 No {for sealed type transformers (for all
ratings) and non-sealed type transformers (for rating 200 KVA& above)}.
Signature of Tenderer Company’s Round Seal Date Place
Page 24 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

p. Non return valve (NRV) -1 No (mandatory for sealed transformer with inert
gas, otherwise optional).
q. Anti-theft stainless steel fasteners with breakaway nut at Top Cover – 4 Nos.
for 3 Phase and 2 nos. for 1 Phase
r. Oil filter valve (1.25 Inch, nominal size thread) -1 No. at top of tank for 500 KVA
s. Drain-cum-sampling metallic valve with plug(1.25 Inch, nominal size thread) -
1no.for 200 KVA & above transformer at bottom of tank with anti theft
protection cover
t. Off circuit tap changer switch with handle and locking device for 200 KVA &
500 KVA Transformers – 1 No
u. LV Cable holding clamp with accessories for 63 KVA and above.
v. LV earthing arrangement for single phase transformers (LV neutral terminal to
be brought out for earthing)
w. Inspection hole for 500 KVA
x. Prismatic Oil level gauge indicating the position of oil marked with background
of yellow color) as follows.
Min. ( -5 deg.C), 30 deg. C, Max. 90 deg.C

NOTES:
1. Minimum and maximum positions correspond to the operating
temperature of–5°C and 90°C respectively (for non-sealed type
transformer).
2. Only Minimum position corresponds to the operating temperature
of 30°C (for sealed type transformers).
5.13 OVER LOAD PROTECTION:
5.13.1 The transformer shall have external mounted LT circuit breaker on the
secondary side up to 25 KVA capacity of transformer. The breaker shall be
housed in an enclosure confirming to IP44 as per IS: 13947 forming integral
part of the transformer. Suitable louvers fitted with wire gauze shall be
provided to ensure circulation of air but not to allow ingress of rain water. An
operating handle shall be provided outside the enclosure in such a way that
ON & OFF operation of the breaker can be conveniently performed from the
ground level by means of an operating rod. The ON & OFF position of the
handle shall be clearly and bodily mark on the enclosure.
5.13.2 The breaker box shall be mounted on side wall (short side) of the tank
opposite side of the name plate for comfortable wiring at site.
5.13.3 The manufacturer will provide 1.1KV; Stranded PVC insulated armored
Aluminum cable from Transformer terminal to Incoming of MCCB having
below mentioned cable size and the purchaser will connect LT cable to the
outgoing terminals of MCCB after installation of the transformer at site.
Detachable gland plate with bellow mentioned sized cable shrinkable PVC
gland to be provided at the bottom of the enclosure.
Signature of Tenderer Company’s Round Seal Date Place
Page 25 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

5.13.4 The circuit breaker shall generally confirm to the requirement of IS: 13947.
The electrical characteristics of the breaker shall be mentioned by bidder as
follows.
Transformer Full load LV current of Transformer terminal to Breaker cable
rating (KVA) the transformer (Amp) size (minimum)-Alum.
5 16.2 2.5 mm²
10 13.33 4 mm²
16 21.33 6 mm²
25 33.33 10 mm²
The circuit breaker shall confirmed to IS: 13947 part-II and certificate from
government approved laboratory for short circuit test at a power factor
not exceeding 0.4 (lagging) shall be submitted with the offer.
5.13.5 MCCB Make mentioned in Schedule A or other makes having type tested as
per relevant IS and approved by the GUVNL/PGVCL/MGVCL /DGVCL /UGVCL
shall only be used & are acceptable. Bidder shall have to mention the make of
MCCB to be provided with the offer. The bidder shall also submit the type test
certificate. However any other make of MCCB having valid BIS Certificate of ISI
mark shall be acceptable only at the discretion of the Purchaser. The decision
of Purchaser shall be final & binding in this regard. For other make of MCCB,
Bidder shall also have to submit certificate of satisfactory operation from
other two Utilities.
The successful bidder shall be required to furnish the guarantee certificate of
05 (five) year obtained from the MCCB manufacture on Rs. 100/- non-judicial
stamp paper.
5.13.6 The circuit breaker shall have the following time v/s current characteristics
and same shall be tested with all the 3 Ph. Loaded. The reference calibration
temperature of the breaker shall be 50 degree centigrade. The test certificate
for the same of NABL accredited laboratory shall be produced with bid as well
as at the time of inspection.
Multiple of normal Tripping time
current setting

1.05 Times More than 2.5 Hrs.

1.1 Times More than 2 Hr. & less than 2.5 Hrs.
1.15 Times More than 1 Hr. & less than 2 Hrs.
1.2 Times More than 0.5 Hrs. & less than 1 Hr.
1.3 Times Less than 20 minutes
1.4 Times Less than 10 minutes
2.5 Times Less than 1 minute
Signature of Tenderer Company’s Round Seal Date Place
Page 26 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Multiple of normal Tripping time

current setting

6.0 Times Less than 5 seconds

8.0 Times Less than 40 milliseconds
12.0 Times Instantaneous (less than 20 milliseconds)
5.13.7 The LT circuit breaker and the associated terminals / wiring shall be
designed with reference to ambient temperature of 55˚C instead of 40 ˚C
due to operation in metallic enclosure installed outdoors. The permissible
temperature rise limits stipulated in IS: 13947 shall be reduced accordingly
and the supplier shall furnish necessary data to show that all the
components are suitable for the expected temperature rise over and
above the ambient temperature 55˚C under various loading conditions.
The supplier shall furnish all the type and routine test certificate of the
circuit breakers in accordance with IS: 13947 pt. 2.
5.14 FASTENERS:
All bolts/nuts/washers exposed to atmosphere shall be of stainless steel.
All bolts, studs, screw threads, pipe threads, bolt heads and nuts shall
comply with the appropriate Indian Standards for metric threads, or the
technical equivalent. Bolts or studs shall not be less than 6 mm in diameter
except when used for small wiring terminals.
All nuts and pins shall be adequately locked.
Wherever possible bolts shall be fitted in such a manner that in the event
of failure of locking resulting in the nuts working loose and falling off, the
bolt will remain in position.
Each bolt or stud shall project at least one thread but not more than three
threads through the nut, except when otherwise approved for terminal
board studs or relay stems. If bolts nuts are placed so that they are
inaccessible by means of ordinary spanners, special spanners shall be
provided.
Two bolts shall be provided diagonally with sealing facility at Top.
The length of the screwed portion of the bolts shall be such that no screw
thread may form part of a shear plane between members.
Taper washers shall be provided where necessary.
Protective washers of suitable material shall be provided front and back or
the securing screws.

5.15 OVERLOAD CAPACITY

The Transformers shall be suitable for loading as per IS:6600/1972 with
latest amendment, if any.
Signature of Tenderer Company’s Round Seal Date Place
Page 27 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

5.16 SUBMISSION OF DRAWINGS AND CALCULATION SHEET:

The manufacturer has to submit the following details and drawings along
with offer.
i. General Arrangement.
ii. Internal Construction.
iii. Name Plate as per approved drawing.
iv. Technical Details Sheet.
v. HV Bi metallic connectors, clearly mentioned ampere capacity.
vi. LV Bi metallic connectors (above 25 KVAcapacity), clearly
mentioned ampere capacity.
vii. Month & Year of manufacture to be written on conservator tank &
body.
viii. Core details.
ix. Metal part of HV/LV steams.
x. Breather
xi. Pressure Relief Device
xii. Short circuit capacity calculation sheet.
xiii. Cooling capacity calculation.
xiv. Guaranteed technical particulars as per DISCOM‘s prescribed
Performa for design & constructional details.
xv. Flux density calculation sheet.
xvi. MCCB box drawing (up to 25 KVA capacity)
xvii. Drawing of combined name plate (minimum size 105mm x 175 mm
x 1.5 mm) showing : Name of Supplier, A/T No., KVA capacity.,
Month & year of manufacturing, Sr.No. of Transformer etc.as per
cl.no. 5.11.2 of technical specifications
xviii. Drawing of Transformer Identification Number plate minimum size
150 mm x 20 mm x 1.5 mm) as per cl.no. 5.11.3 of technical
specifications

The above drawings/ details are illustrative. However, the bidder may
submit their own drawing/ details if they so desires. Offer without
drawings/ details shall not be considered.

After Placing of order by the respective DISCOM to successful bidder,

suppler has to get approval of all above drawings before offering
Prototype sample for inspection.

5.17 THE INSPECTION AND TESTING :

5.17.1 INSPECTION OF PROTO TYPE TRANSFORMER :
The Manufacturer shall have to offer one no of prototype transformer along
with relevant approved drawings as stated above at clause 5.14.

Signature of Tenderer Company’s Round Seal Date Place

Page 28 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

The proto type shall be subjected to following test conforming to IS 1180 Part-
1 2014 & IS 2026 and all relevant IS with latest amendments.
1) Verification of core laminations material documents and quality.
2) Verification of internal parameters with respect to approved
drawings and GTP.
3) All Routine tests/ acceptance test as per clause 6
4) Temperature rise test as per clause no.6
5) Verification of Air pressure and vacuum test certificate from
manufacturer of tank.
On completion of proto type sample inspection and scrutinizing the reports,
approval will be accorded by the respective DISCOM. On getting approval
from respective DISCOM, bulk production shall be commenced by the
supplier.
If any observation/ deviation found during proto inspection, supplier shall
have to re-offer proto inspection with rectification/ new sample. However,
inspection charges for un-successful proto sample will be borne by the
supplier.

6.0 TESTS:
a. All the equipment offered shall be fully type tested by the bidder or his
collaborator as per the relevant standards including the additional type
tests mentioned at clause 6.2. The type test must have been conducted on
a transformer of same design. The Bidder shall furnish four sets of type
test reports along with the offer. All the required Type test reports for the
tendered items as under should invariably furnish a Notarized Copy. Offers
without type test reports will be treated as Non-responsive.
1. Temperature rise test for determining the maximum
temperature rise after continuous full load run.
2. Lightening Impulse voltage test: As per Clause No. 13 (With
chopped wave) of IS – 2026- part-III latest version. BIL for 11
kV shall be minimum 95 KV Peak.
3. Vacuum Test: As per IS - 1180 / part-I/2014
4. Air Pressure Test: As per IS - 1180 / part-
I/2014ORTransformer tank together with its radiator and
other fittings shall be subjected to pressure corresponding to
twice the normal pressure or 0.35 kg / sq.cm whichever is
lower, measured at the base of the tank and maintained for
an hour. The permanent deflection of the flat plates after the
excess pressure has been released, shall not exceed the
figures for vacuum test.
5. Short Circuit withstand test: Thermal and dynamic ability.
6. Magnetic Balance Test.
7. Noise-level measurement.

Signature of Tenderer Company’s Round Seal Date Place

Page 29 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

8. Measurement of zero-phase sequence impedance.

9. Measurement of Harmonics of no-load current.
10. Pressure relief device test (if provided).The pressure relief
device shall be subject to increasing fluid pressure. It shall
operate before reaching the test pressure as specified in the
above class. The operating pressure shall be recorded. The
device shall seal-off after the excess pressure has been
released.
11. Type tests for MCCB as per relevant IS (Upto 25KVA)
b. Special tests other than type and routine tests, as agreed between
purchaser and Bidder shall also be carried out as per the relevant
standards.

6.1 ROUTINE TESTS:

Following tests shall have to be carried out by manufacturers at their works
(to be conducted on all units) before offering proto/lot acceptance tests and
record of the same shall be maintained and produced at the time of
acceptance tests for inspector’s verification.
1. Measurement of winding resistance (at all taps if applicable)
[IS2026 (Part1)].
2. Measurement of voltage ratio, polarity, phase sequence and vector
group[IS2026(Part1)].
3. Measurement of short-circuit impedance (principal tapping,
when applicable)
4. Load losses at rated current and normal frequency,at50 %
and100 % load [IS2026(Part1)].
5. Measurement of no-load loss and current [IS2026(Part1)].
6. Measurement of insulation resistance [IS2026(Part1)].
7. Induced over-voltage withstand test[IS2026 (Part3)].
8. Separate-source voltage withstand test [IS2026(Part3)].
9. Pressure and vacuum test(as per IS: 1180-2014).
10. Oil leakage test(as per IS: 1180-2014).
11. Neutral current measurement, shall not be more than 2% of full load
current (CEA Guideline 2008 clause no 34.9)
12. Oil samples (one sample per lot) to comply with IS 1866.
13. Measurement of no load losses and magnetizing current at rated
frequency and at 90%, 100%and 112.5% voltage.

6.2 TYPE TESTS TO BE CONDUCTED ON ONE UNIT:

As per Clause No 6

6.3 ACCEPTANCE TESTS :

Signature of Tenderer Company’s Round Seal Date Place

Page 30 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

The following tests shall be carried out on transformers in the presence of

purchaser’s representative at the supplier’s works before dispatch without
any extra charges.

The testing shall be carried out in accordance with IS: 1180Part-1 2014 and
IS:2026 latest amendment& CEA Guideline as applicable.

Valid calibration certificates from NABL lab of testing equipment’s shall be

available at supplier works for testing of transformers. Manufacturer shall
possess 0.1 class of accuracy instruments for measurement of losses.

A: Physical verification to be carried out on one transformer from offered

lot:-
1. Checking of weights of individual components and total weight,
dimensions, fitting and accessories, tank sheet thickness, oil
quantity, materials, finish and workmanship as per GTP , QA Plan and
approved drawings.
2. Verification of thickness of paint coating.
3. Physical verification of core coil assembly and measurement of flux
density of one unit of each rating, in every inspection with reference
to short circuit test report.
B:Test to be carried out on all transformers:-
1. Measurement of load loss at 50 % and 100 % load at maximum
current tap.
2. Measurement of short-circuit impedance at normal tapping.
3. Neutral current to be measured by clamp-on meter, it shall not be
more than 2% of full load current (CEA Guideline 2008 clause no
34.9)
4. Measurement of no load losses& current at rated frequency and
voltage. [IS2026(Part1)].
5. Measurement of over excitation current at rated frequency and at
112.5% voltage.
6. Induced over-voltage withstand test[IS2026 (Part3)].
7. Separate-source voltage withstand test [IS2026(Part3)].
8. Physical verification of finishing and workmanship as per GTP and QA
Plan and approved drawings.
9. Verification of oil level through oil level gauge.

C: Test to be carried out on one transformer from offered lot:-

1. Measurement of winding resistance [IS2026 (Part1)].
2. Measurement of voltage ratio, polarity, phase sequence and
Signature of Tenderer Company’s Round Seal Date Place
Page 31 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

vector group[IS 2026(Part1)].

3. Pressure test (as per IS: 1180-2014).
4. Measurement of insulation resistance [IS2026(Part1)].
5. Oil leakage test (as per IS: 1180-2014).
6. Collection of Oil samples from any transformer, to be sent for
testing at NABL lab to comply with IS 1866.Testing charges will be
borne by DISCOM.
7. Magnetic balance test.
8. Temperature Rise Test on transformer having maximum load
losses from each offered lot (Total losses guaranteed, offered in
GTP at maximum current tap shall have to be fed for Temperature
rise test).
9. To ascertain the quality of the transformer oil, the original
manufacturer’s tests report should be submitted at the time of
inspection. Arrangements should also be made for testing of
transformer oil, after taking out the sample from the manufactured
transformers and tested in the presence of purchaser’s
representative.
10. Acceptance test for MCCB:-
(a) Verification for make of MCCB
(b) High Voltage test – 3KV (On random sample)
(c) Amp/Time curve characteristics (On random sample).

6.4 TOLERANCES:
Unless otherwise specified herein the test value of the transformers supplied
would be within the tolerance permitted in the relevant standards. No
positive tolerance is allowed on guaranteed losses.

7.0 INSPECTION:
All tests and inspection shall be made at supplier works mentioned in A/T. The
manufacturer shall afford the inspector representing the purchaser all
reasonable facilities, without charge to satisfy him that the material is being
furnished in accordance with specification.

The manufacturer shall provide all services to establish and maintain quality of
workman ship in his works and that of his sub-contractors(for bought out
material/equipments)to ensure the mechanical / electrical performance of
components, compliance with drawings, identification and acceptability of all
materials, parts and equipment as per latest quality standards of ISO 9000.

Signature of Tenderer Company’s Round Seal Date Place

Page 32 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Along with the bid the manufacturer shall prepare Quality Assurance Plan
identifying the various stages of manufacture, quality checks performed at
each stage and the Customer hold points. The document shall also furnish
details of method of checking, inspection and acceptance standards / values.
However, purchaser or his representative shall have the right to review the
inspection reports, quality checks and results of manufacturer’s in house
inspection department which are not customer hold points and the
manufacturer shall comply with the remarks made by purchaser or his
representative on such reviews with regards to further testing, rectification or
rejection etc. Manufacturer should submit the list of equipment for testing
along with valid calibration certificates from NABL accredited laboratory to
the purchaser along with the bid.

Purchaser shall have every right to appoint a third party inspection to carryout
the inspection process. The purchaser has reserved the rights to have the test
carried out at his own cost by an independent agency at NABL accredited
laboratory, wherever the dispute regarding the quality of supplies arise.

8.0 QUALITY ASSURANCE PLAN:

8.1. The Bidder shall invariably furnish following information along with his bid,
failing which his bid shall be liable for rejection. Information shall be
separately given for individual type of equipment offered.

i. Statement giving list of important raw materials, names of sub-suppliers for

the raw materials, listof standards according to which the raw materials
are tested. List of tests normally carried out on raw materials in the
presence of Bidder’s representative, copies of test certificates.
ii. Information and copies of test certificates as in (i) above in respect of
bought out accessories.
iii. List of manufacturing facilities available.
iv. Level of automation achieved and list of areas where manual processing
exists.
v. List of areas in manufacturing process, where stage inspections are
normally carried out for quality control and details of such tests and
inspection.
vi. List of testing equipment available with the bidder for final testing of
equipment along with valid calibration reports shall be furnished with the
bid. Manufacturer shall possess 0.1 class accuracy instruments for
measurement of losses.

Signature of Tenderer Company’s Round Seal Date Place

Page 33 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

vii. Quality Assurance Plan (QAP) with all points for purchaser’s inspection.
8.2 The successful Bidder shall within 30 days of placement of order, submit
following information to the purchaser.
i. List of raw materials as well as bought out accessories and the names of sub-
suppliers selected from those furnished along with offer.
ii. Type test certificates of the raw materials and bought out accessories.
8.3 The successful Bidder shall submit the routine test certificates of bought out
accessories and central excise passes for raw material at the time of routine
testing.
9.0 DOCUMENTATION:
The Bidder shall furnish along with the bid the dimensional drawings of the
items offered indicating all the fittings.
i) Dimensional tolerances
ii) Weight of individual components and total weight

10.0 PACKING & FORWARDING:

The packing shall be done as per the manufacturer’s standard practice. However, it
should be ensured that the packing is such that, the material would not get
damaged during transit by Rail / Road / Sea.The marking on each package
shall be as per the relevant IS.
11.0 DRAWINGS:
One copy of the dimensional drawing and internal construction drawing of
each rating transformer shall be submitted with the tender. These drawings
shall be of A-3(420 x 297 mm) size only. Guaranteed and other technical
particulars of the transformers as per the A/T shall also be submitted in A-4
size for approval in the Performa attached with tender only.

12.0 GTP : GUARANTEED TECHNICAL PARTICULARS FOR TRANSFORMERS.

GTP to be filled in and submitted by the tenderer in the Annexure I, attached
with the tender. In Annexures, the specific values shall be furnished and only
quoting of IS reference is not sufficient. If the Annexures are not submitted
duly filled in with the offer, the offer shall be liable for rejection.

The discrepancies between the specification and the catalogues, literatures

and indicative drawings which are subject to change, submitted as part of the
offer, shall not be considered and representation in this regard will not be
entertained.

Signature of Tenderer Company’s Round Seal Date Place

Page 34 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

If it is observed that there are deviations in the offer in G.T.P. or those

specified in the relevant Annexure of Commercial terms and Condition then
such deviations shall be treated as deviations. The deviation brought out shall
be supported by authentic documents, standards and clarifications, otherwise
the offer may be liable for rejection.

The tenderer shall submit the list of orders for similar type of equipments,
executed or under execution during last three years, with full details to enable
the purchaser to evaluate the tender.

13.0 TENDER DRAWINGS AND OTHER DETAILS TO BE ENCLOSED:

The bidder shall submit drawings and details listed in clause no 5.14 along with offer
as well as before offering the prototype transformer.

14.0 AUDIT INSPECTION:

The representative of the Company may pick up samples from the lots supplied by
the Supplier at the Stores location of the Company at random for quality check. The
samples picked up will be tested for acceptance tests / type tests or as decided by
DISCOM at Government approved laboratory in presence of representatives of
supplier and DISCOM as per relevant ISS/BIS/ DISCOM P.O. specifications. In case if
the materials does not confirm to specifications or fails at Government approved
laboratory or other laboratory decided by DISCOM for testing and if subsequent
testing are to be carried out (which will solely at DISCOM discretion),then all Testing
fees, expenses of the inspector and other expenses incurred by DISCOM will be to
supplier’s account. The decision in this regard for acceptance a sabove of DISCOM
shall be final and this will be binding on the supplier.

The test results will be binding on the suppliers. DISCOM in general will not allow re-
sampling. If the material fails in any of the acceptance tests/type tests carried out
(except for no load and load losses), the full lot of materials will be considered as
rejected, and if replacement is not possible due to consumption of the materials, in
that case for whole of the rejected lot, DISCOM will deduct penalty as per below
mentioned details. If the same are not utilized / consumed, Company at sole
discretion may ask for replacement or may accept with penalty having details as
under and all these will be binding on the supplier.

In case of failure of sample in testing other than losses:

To reject the complete lot OR recovery of penalty up to 30% in line with commercial
condition clause of audit testing.

Signature of Tenderer Company’s Round Seal Date Place

Page 35 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

In case of failure of sample in testing as well as losses:

To reject the complete lot OR recovery of both type penalty as under.

1.Up to 30% penalty in line with commercial condition clause of audit testing.

2.Excess losses penalty as under.

i. Rs. 493.52 per Watt for No load loss.

ii. Rs. 272.92 per Watt for Load loss.

15.0 GUARANTEE FOR THE TRANSFORMERS;

1. Guarantee period shall be 60 months from the date of installation or 66
months from the date of receipt by purchaser whichever is earlier. If the
goods, stores and equipment found defective due to bad design or
workmanship the same should be repaired or replaced by you free of
charge if reported within 66 months of their receipt at site or 60 months
from the date of commissioning of equipment whichever is earlier. You
will be responsible for the proper performance of the equipment /
materials for the respective guarantee period.
2. The supplier shall return guarantee failed transformers duly repaired and
tested as per approved GTP and tender specification within 45 days from
the date of receipt at repair shop without any cost. If the same is not
repaired / replaced within stipulated period, then the end cost of such
equipment will be retained by way of recovering the amount from
Suppliers pending / ensuing bills with the Company / other subsidiary
Companies of GUVNL against any of the order, and / or by encashing
Bank Guarantee available with the Company / other subsidiary
Companies of GUVNL against any of the order, till the return of the
equipment. No interest will be paid on the amount so retained /
recovered. In case of material / item not returned duly repaired within
45 days, penalty shall be imposed @ 0.5% per week or part thereof,
maximum up to 10% of the cost of undelivered material / equipment
beyond specified time limit. In case of material / item not returned duly
repaired within 5 months, total cost of the material/ item alongwith
penalty will be adjusted/recovered from the pending bills of the supplier
or encashing available performance bank guarantee submitted against
guarantee period. This clause itself shall be the notice to the supplier
about encashment of Bank Guarantee in case of his failure to adhere to
timelines & no separate notice will be served.The outage period i.e.
period from the date of failure till unit is repaired/ replaced shall not be
counted for arriving at the guarantee period.
3. After intimation of failure of transformer failed within guarantee period,
DISCOM will arrange for the dispatch of guarantee period failed
Signature of Tenderer Company’s Round Seal Date Place
Page 36 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

transformer to firm’s works at the cost of DISCOM. On receipt of

guarantee period failed transformer at firm’s works, the external
inspection will be carried out by the representative of DISCOM not below
the rank of Junior Engineer. The cost of any outer component damage
not because of supplier’s fault and required to be provided will be
reimbursed to the supplier as per the approved rate of DISCOM on the
strength of joint external inspection report.
No internal inspection of failed unit is to be carried out in presence of
representative of DISCOM. However, the supplier may prepare an
internal inspection report of failed unit for his study and analysis. If
required, such analysis shall be furnished to DISCOM.
Testing of transformer will be done in presence of company’s Engineer to
ensure losses as per GTP, Transformer found with higher losses than GTP
will not be accepted and cost thereof will be recovered. The new
Transformers supplied in this circumstances must as per GTP submitted
with tender and shall match the losses offered by the supplier as per
Tender.
The testing of each G.P.failed transformers will be carried out for all
acceptance test as per the relevant standard where no load losses and
load losses are also required to be maintained identical as per GTP.
4. The supplier situated outside Gujarat State shall have to establish
suitable and adequate arrangement for repairing and testing of failed
transformer in Gujarat State at his cost. This arrangement shall have to
be continued up to the completion date of guarantee period of supply of
last lot.
16.0 THE TENDERER SHALL OFFER EITHER CONVENTIONAL CORE TYPE OF TRANSFORMER OR
WOUND CORE TYPE OF TRANSFORMER. TENDERER SHALL NOT OFFER OR QUOTE THE RATE
FOR BOTH TYPE OF TRANSFORMER AT A TIME WITH THIS TENDER.

Schedule A
H.V. BUSHINGS
1) JAYASHREE
2) BEPCO.
3) W.S. INSULATORS
4) ASSOCIATED PORCELAIN (11KV ONLY)
5) JAIPUR GLASS
6) SESHASAYEE
7) LUSTER CERAMICS
8) AGRAWAL SALT CO., BIKANER.
9) B.P.P.L., BIKANER.
10) VENKATESHWARA CERAMICS P.
11) CJI PORCELAIN INDIA LTD.
12) MAXWELL CERAMIC, WADHWAN, (ONLY 11KV)
13) RAVIKIRAN (ONLY 11KV)
14) VISHAL MALLEABLE LTD.
Signature of Tenderer Company’s Round Seal Date Place
Page 37 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

15) AS INSULATOR
16) REAL INSULATOR
17) REDIANT CERAMIC
18) SUN INSULATOR
19) PRIME INSULATOR
20) GENESIS ENTERPRISES PRIVATE LIMITED

L.V. BUSHINGS:
1) J.S.I. (RISHRA)
2) LUSTER CERAMICS
3) JAIPUR GLASS
4) AGRAWAL SALT CO., BIKANER.
5) B.P.P.L., BIKANER.
6) VENKATESHWARA CERAMICS, PVT. LTD.
7) CJI PORCELAIN
8) MAXWELL CERAMIC, WADHWAN.
9) RAVIKIRAN
10) VISHAL MALLEABLE LTD.
11) AS INSULATOR
12) REAL INSULATOR
13) REDIANT CERAMIC
14) SUN INSULATOR
15) PRIME INSULATOR
16) GENESIS ENTERPRISES PRIVATE LIMITED
MCCB:

1) Siemens
2) L&T
3) ABB
4) GE POWER
5) Schneider
6) Crompton Greaves
7) Havells
8) HPL

Signature of Tenderer Company’s Round Seal Date Place

Page 38 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Annexure I
GUARANTEED TECHNICAL PARTICULARS

Sr. Particulars Unit / Type As per Firm's

No. Offer
1 Name of manufacturer
2 Place of Manufacturing
3 Transformer capacity KVA
4 Voltage 11/0.433-0.250 KV
5 No. of Phases 3 No./1 No.
6 Vector Group DY-11
7 Type of Cooling ONAN
8 Type of Transformer Sealed/Unsealed
9 For 200 KVA/500 KVA transformers
a) No. of tap positions in HV winding
b) Voltage variation
10 Energy Efficiency Level Level-1/Level-2

11 Losses
i Core loss Watts
a) at Normal Voltage Watts
b) at Maximum Voltage Watts
ii Full Load losses at 75 deg.C. Watts
iii Total losses at 50 % loading at 75 deg.C. Watts
iv Total losses at 100 % loading at 75 deg.C. Watts
12 Percentage Impedance at 75 deg.C. %
13 Maximum temperature rise of
a) Windings by resistance method 40 deg C
(35 deg C for 5KVA)
b) Oil by Thermometer 35 deg C
(30 deg C for 5KVA)
14 Clearances
a) Core & LV mm
b) LV & HV mm
c) HV Phase to Phase mm
d) End insulation clearance to Earth mm
e) Any point of winding to tank mm
Signature of Tenderer Company’s Round Seal Date Place
Page 39 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Sr. Particulars Unit / Type As per Firm's

No. Offer
f) HV to earth creepage distance mm
g) LV to earth creepage distance mm
15 Efficiency at 75 deg.C.
a) Unity P.F.
1) 125% load %
2) 100% load %
3) 75% load %
4) 50% load %
5) 25% load %
b) 0.8 P.F.
1) 125% load %
2) 100% load %
3) 75% load %
4) 50% load %
5) 25% load %
16 Regulation at
a) Unity P.F.
b) 0.8 P.F. at 75 deg.C.
17 CORE CRGO/ Amorphous
i Core Grade
ii Core diameter mm
iii Gross Core area Mtr²
iv Net Core area Mtr²
v Flux density Wb/Mtr²
vii Wt. of Core Kg
viii Loss per kg. of Core at the specified Flux Watts
density
ix Core window height mm
x Centre to centre distance of the core mm
xi The nominal flux density at
a) 100% rated voltage ≤ 1.69 Wb/Mtr²
b) 110% of rated voltage ≤1.9 Wb/Mtr²
xii % No load current of full load current at rated
voltage and frequency on the secondary and
Increase of voltage by 112.5%

Signature of Tenderer Company’s Round Seal Date Place

Page 40 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Sr. Particulars Unit / Type As per Firm's

No. Offer
(i) CRGO Core: at 100% and 112.5% of rated
Voltage
a) Up to 200 KVA Transformer ≤ 3% and ≤ 6 %
b) Above 200 KVA Transformer ≤ 2% and ≤ 5 %
(ii) Amorphous Core: at 100% and 112.5% of
rated Voltage
a) All Ratings ≤ 2% and ≤ 5 %
18 WINDINGS Aluminium / Copper
i No. of L.V. Turns No.
ii No. of H V turns No.
iii Size of LV Conductor bare/ covered mm
iv Size of HV conductor bare/covered mm
v No. of parallels No.
vii Resistance of HV winding at 20 deg.C Ohm
viii Resistance of LV winding at 20 deg.C Ohm
ix Current density of LV winding Amps/sq.mm.
x Current density of HV winding Amps/sq.mm.
xi Wt. of the LV winding for Transformer kg.
xii Wt. of the HV winding for Transformer kg.
xiii No. of LV Coils/phase No.
xiv No. of HV coils / phase No.
xv Height of LV Windings mm
xvi Height of HV winding mm
xvii ID/OD of LV winding mm
xviii ID/OD of HV winding mm
xix Size of the duct in LV winding mm
xx Size of the duct in HV winding mm
xxi Size of the duct between HV & LV mm
xxii Inter layer insulation provided in design for
1) Top & bottom layer
2) In between all layer
3) Details of end insulation
4) Whether wedges are provided at 50% turns of
the HV coil

xxiii Insulation materials provided

Signature of Tenderer Company’s Round Seal Date Place

Page 41 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Sr. Particulars Unit / Type As per Firm's

No. Offer
a) For Conductors
(1) HV
(2) LV
B) For Core
xxiv Material and Size of the wire used
1) HV a) SWG No.
b) Dia mm
2) LV a) Strip size mm X mm
b) No. of Conductors in parallel No
c) Total area of cross section sq.mm.
19 Weight content of
a) Core lamination (min) KG
b) Windings (min) Aluminium/Copper KG
c) Tank & Fittings KG
d) Oil KG
e) Oil qty (min) Litre
f) Total Weight KG
20 Oil Data
1. Qty for first filling (min) Litre
2. Grade of oil used
3. Maker’s name
4. BDV at the time of filling KV
21 Transformer
1) Overall length x breadth x height mm X mm X mm
2) Shape of Tank
2) Tank length x breadth x height mm X mm X mm
3) Thickness of plates for
a) Side plate (min) mm
b) Top & Bottom plate (min) mm
4) Conservator Dimensions mm X mm
5) Tank base channel dimensions mm X mm X mm
22 HV Bushings & Terminals
1) Make of HV bushing
2) Rating in KV KV
3) Turret Height mm

Signature of Tenderer Company’s Round Seal Date Place

Page 42 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Sr. Particulars Unit / Type As per Firm's

No. Offer
4) Material of HV terminal Brass/Copper
5) Current Density of HV terminal Amps/sq.mm.
23 LV Bushings & Terminals
1) Make of LV bushing
2) Rating in KV KV
3) Turret Height mm
4) Material of LV terminal Brass/Copper
5) Current Density of LV terminal Amps/sq.mm.
24 Details of MCCB
(for transformers having rating upto 25 KVA)
Make
Rated thermal current Amp.
Current setting Amp.
Minimum short circuit breaking current KA
25 Radiation
1) Heat dissipation by tank walls exclusive top &
bottom
2) Heat dissipation by cooling tube
3) Dia & thickness of cooling tube
4) Whether calculation sheet for selecting cooling Yes/No
area to ensure that the transformer is capable of
giving continuous rated output without exceeding
temperature rise is enclosed.

26 Whether the name plate gives all particulars as Yes/No

required in Tender
27 Whether the transformer offered is already type Yes/No
tested for the design and test reports enclosed

Signature of Tenderer Company’s Round Seal Date Place

Page 43 of 44
 SHORT NOTICE TENDER No. UGVCL/SP/I/CPP/884/16KVA Star 1 DTR.

Annexure II
Digit/letter Details TIN Remark
No.
Name of
1 M First letter of DISCOM name
Company
for 5/10/16/25/63/100/200/500
2 KVA rating 5 KVA ratings digits will be
respectively 1/2/3/4/5/6/7/8
Type of Core
3 1 CRGO-1,Amorphous-2
Material
Core
4 1 Stack-1, Wound-2
construction
5 1 each supplier will be given 2
Supplier Name
digit code no.
Code
6 5 e.g. M/s XYZ given code no.15

7 0
Month of 2 digits for Month of
manufacturing manufacturing
8 2

9 1
Year of 2 digits for Year of
manufacturing manufacturing
10 7

11 9

12 0
CPP Tender
4 digits for CPP tender no.
No.
13 3

14 2
5 digits for transformer sr. no.
15 0
given by supplier
Sr. No. of
16 0 (e.g. M/s XYZ will give
transformer
17 0 transformer sr. no. from 00001
given by
18 0 to 00260 for P.O. of 260 no.
Supplier
transformers issued to them vide
19 1 CPP tender no.9032 )

Signature of Tenderer Company’s Round Seal Date Place

Page 44 of 44