LEGEND fig.1.

Incase that you want to wire DHT22 sensor use

Red - 12-36DC scheme from fig.2.
Black - GND 2.In case that you want to connect binary sensor (Reed
or Black and RED -12-24AC Ampule) use scheme from fig.3A for DC power supply or
White - ADC Input fig.3B for AC power.
UNIVERSAL WIFI SENSOR INPUT Yellow - VCC 3.3VDC output 3.In Case that you want to connect button or switch to
USER GUIDE Blue - DATA the device use the scheme from fig.4A for DC power
Green - Internal GND supply or fig.4B for AC power.
Light Brown - Input 1
Dark Brown - Input 2
fig. 4B 4.For wiring a ADC use scheme from fig.6

OUT_1 – Maximum Current 100mA, Maximum Voltage CONTROL OF THE INPUTS

AC: 24V / DC: 36V • Reading of standard logical levels, independent from
OUT_2 – Maximum Current 100mA, Maximum Voltage the applied voltage on the inputs(potential free)
AC: 24V / DC: 36V • It cannot work with programed limits of the levels, be-
cause they aren‘t ADC attached to the inputs
Wiring of buttons and switches • When there is Voltage from:
• AC 12V up to 24V – it is measured as logical “1”
(HIGH). Only when the voltage is below 12V it is mea-
sured as logical “0” (LOW)
• DC: 2,2V up to 36V – it is measured as logical “1”
(HIGH). Only when the voltage is below 2,2V it is mea-
sured as logical “0” (LOW)
• Maximum allowed Voltage - 36V DC / 24V AC
fig. 1
fig. 5 For more information about the Bridge, please visit:
http://shelly-api-docs.shelly.cloud/#shelly-family-overview
or contact us at: [email protected]
You may choose if you want to use Shelly with the Shelly
Cloud mobile application and Shelly Cloud service. You
can also familiarize yourself with the instructions for
Wiring of DS18B20 sensor Management and Control through the embedded Web
Wiring of load interface.

CONTROL YOUR HOME WITH YOUR VOICE

All Shelly devices are compatible with Amazon Echo and
Google Home. Please see our step-by-step guide on:
https://shelly.cloud/compatibility/Alexa
https://shelly.cloud/compatibility/Assistant
fig. 2
fig. 6

Wiring of DHT22 sensor

Hazardous voltage presents on bouth side of the product!
Wiring of ADC

DC 2,2V - 36V DC 2,2V - 36V

SPECIFICATION through HTTP protocol.
Power supply: Radio signal power: 1mW An API can be provided by the Manufacturer. Shelly® de-
fig. 3A • 12V-36V DC
• 12V-24V AC
Radio protocol:
WiFi 802.11 b/g/n
vices may be available for monitor and control even if the
User is outside the range of the local WiFi network, as
Max Load: Frequency:
long as the WiFi router is connected to the Internet. The
100mA/AC 24V/DC 3 6V, 2400 – 2500 MHz;
Max 300mW Operational range (depend-
cloud function could be used, which is activated through
Complies with EU standards: ing on local construction): the web server of the Device or through the settings in
• RE Directive 2014/53/EU • up to 50 m outdoors the Shelly Cloud mobile application. Shelly Cloud gives you opportunity to control and adjust
• LVD 2014/35/EU • up to 30 m indoors The User can register and access Shelly Cloud, using ei- all Shelly® Devices from anywhere in the world. You only
Wiring of binary sensor(Reed Ampule) • EMC 2004/108/WE Dimensions: ther Android or iOS mobile applications, or any internet need an internet connection and our mobile application,
• RoHS2 2011/65/UE HxWxL 20 x 33 x 13 mm browser and the web site: https://my.Shelly.cloud/. installed on your smartphone or tablet. To install the ap-
Working temperature: Electrical consumption: plication please visit Google Play (left screenshot) or App
0°C up to 40°C <1W
INSTALLATION INSTRUCTIONS Store (right screenshot) and install the Shelly Cloud app.
CAUTION! Danger of electrocution. The mounting/instal-
TECHNICAL INFORMATION lation of the Device should be done by a qualified person
The universal sensor input Shelly® UNI can operate with: (electrician).
• Up to 3 DS18B20 sensors, CAUTION! Danger of electrocution. Even when the De-
• Up to 1 DHT sensor, vice is turned off, it is possible to have voltage across
fig. 3B • ADC input its clamps. Every change in the connection of the clamps
• 2 x binary sensors, has to be done after ensuring all local power is powered
• 2 x open collector outputs. off/disconnected.
CAUTION! Do not connect the Device to appliances ex-
CAUTION! Danger of electrocution. Mounting the device ceeding the given max load!
to the power has to be performed with caution. CAUTION! Connect the Device only in the way shown in
CAUTION! Do not allow children to play with the button/ these instructions. Any other method could cause dam-
Wiring of binary sensor(Reed Ampule) switch connected the Device. Keep the Devices for re- age and/or injury.
mote control of Shelly (mobile phones,tablets,PCs away CAUTION! Before beginning the installation please read
from children. the accompanying documentation carefully and com-
pletely. Failure to follow recommended procedures could
INTRODUCTION TO SHELLY® lead to malfunction, danger to your life or violation of the
Shelly® is a family of innovative Devices, which allow law. Allterco Robotics is not responsible for any loss or Registration
DC 2,2V - 36V DC 2,2V - 36V remote control of electric appliances through mobile damage in case of incorrect installation or operation of The first time you load the Shelly Cloud mobile app, you
phone, PC or home automation system. Shelly® uses this Device. have to create an account which can manage all your
CAUTION! Use the Device only with power adapter which
fig. 4A WiFi to connect to the devices controlling it. They can be
in the same WiFi network or they can use remote access comply with all applicable regulations. Defective power
Shelly® devices.

(through the Internet). Shelly® may work standalone, adapter connected to the Device may damage the Device. Forgotten Password
RECOMMENDATION! Тhe Device may be connected to In case you forget or lose your password, just enter the
without being managed by a home automation control-
and may control electric circuits and appliances only if e-mail address you have used in your registration. You
ler, in the local WiFi network, as well as through a cloud
they comply with the respective standards and safety will receive instructions to change your password.
service, from everywhere the User has Internet access.
norms. WARNING! Be careful when you type your e-mail address
Shelly® has an integrated web server, through which the
during the registration, as it will be used in case you for-
Wiring of buttons and switches User may adjust, control and monitor the Device. Shelly®
has two WiFi modes - access Point (AP) and Client mode INITIAL INCLUSION get your password.
(CM). To operate in Client Mode, a WiFi router must be Before installing/mounting the Device ensure that the First steps
located within the range of the Device. Shelly® devic- grid is powered off (turned down breakers). After registering, create your first room (or rooms), where
es can communicate directly with other WiFi devices 1.Connect sensor DS18B20 to the device as shown in you are going to add and use your Shelly devices.
 Step 4 ering it off and on again. Power on shelly Uni and press Shelly Management Settings
Approximately 30 seconds after discovery of any new the reset switch button until the LED on the board goes in Each Shelly can be configured individually. This lets you
Devices оn the local WiFi network, а list will be displayed ON. If not, please repeat or contact our customer support personalize each Device in a unique manner, or consis-
by default in the “Discovered Devices” room. at: [email protected] tently, as you choose.
Step 2
When Shelly has created an own WiFi network (own AP), Power On Default State
with name (SSID) such as shellyuni-35FA58. Connect to This sets the channels’ default state when powered from
it with your phone, tablet or PC. the power grid.
Step 3 • ON - By default when the Device is powered and the
Type 192.168.33.1 into the address field of your browser connected circuit/appliance to it will be powered as well.
to load the web interface of Shelly. • OFF - By default the Device and any connected circuit/
appliance will not be powered, even when it is connected
to the grid.
GENERAL - HOME PAGE • Restore last state - by default the Device and the
This is the home page of the embedded web interface. connected circuit/appliance will be returned to the last
If it has been set up correctly, you will see information state they occupied (on or off) before the last power off/
Shelly Cloud gives you opportunity to create scenes for Step 5 about settings menu button, current state (on/off), pres-
automatic turning on or off of the Devices at predefined shutdown.
Enter Discovered Devices and choose the Device you From the details menu you may control the Device, as ent time.
hours or based on other parameters like temperature, hu- want to include in your account. well as edit its appearance and settings: • Internet & Security - you can configure the internet and Auto ON/OFF
midity, light etc. (with available sensor in Shelly Cloud). • Edit device – allows you to change the Device’s name, WiFi settings Automatic powering/shutdown of the socket and the
Shelly Cloud allows easy control and monitoring using a room and picture. • External sensors - you can set up temperature units connected appliance:
mobile phone, tablet or PC. • Device settings – allows you to change settings. For and offset • Auto OFF after - After turning on, the power supply will
example, with Restrict login you may enter a username • Sensor Url actions - you can configure url actions by be automatically shut down after a predefined time (in
Device Inclusion and password to restrict access to the embedded web
To add a new Shelly device, install it to the power grid channels seconds). A value of 0 will cancel the automatic shut-
interface in Shelly. You may automate the Device opera- • Settings - you can configure different settings -Device down.
following the Installation Instructions included with the
tions from this menu as well. name, ADC range, Firmware • Auto ON after - After turning off, the power supply will
Device.
• Timer -to manage the power supply automatically • Channel 1 - Settings of output channel 1 be automatically turned on after a predefined time (in
Step 1
- Auto OFF - After turning on, the power supply will • Channel 2 - Settings of output channel 2 seconds). A value of 0 will cancel the automatic start.
After the installation of Shelly following the Instalation
automatically shutdown after a predefined time (in There is 2 type of automation:
Instructions and the power is turned on, Shelly will create Manual Switch Type
Step 6 seconds). A value of 0 will cancel the automatic • ADC can control the outputs according off measured
its own WiFi Access Point (AP). • Momentary – When using a button.
Enter a name for the Device (in the Device Name field). shutdown. voltage and set tresholds.
WARNING! In case the Device has not created its’ own • Toggle switch – When using a switch.
Choose a Room, in which the Device has to be posi- - Auto On - After turning off, the power supply will be • Temperature sensors can control also outpits accord-
AP WiFi network with SSID like shellyuni-35FA58, please • Edge switch - Change status on every hit.
tioned. You can choose an icon or add a picture to make automatically turned on after a predefined time (in ing to the measurement and the set tresholds.
check if the Device is connected accordingly to the Insta-
it easier to recognize. Press “Save Device”. seconds). A value of 0 will cancel the automatic
lation Instructions. If you still do not see an active WiFi
power-on. Sunrise/Sunset hours
network with SSID like shellyuni-35FA58, or you want to This function requires an Internet connection. To use
• Weekly schedule - Shelly may turn on/off automatical-
add the Device to another Wi-Fi network, reset the Device. Internet, a Shelly Device has to be connected to a local
ly at a predefined time and day throughout the week. You
If the Device has been powered on, you have to restart WiFi network with а working Internet connection.
may add unlimited number of weekly schedules. This
by powering it off and on again. Power on shelly Uni and Shelly receives actual information through the Internet
function requires an Internet connection. To use Inter-
press the reset switch button until the LED on the board about the time of sunrise and sunset in your area. Shelly
net, a Shelly Device has to be connected to a local WiFi
goes in ON. If not, please repeat or contact our customer may turn on or off automatically at sunrise/sunset, or at a
network with working internet connection.
support at: [email protected] specified time before or after sunrise/sunset.
• Sunrise/Sunset - Shelly receives actual information
Step 2
through the Internet about the time of sunrise and sun- On/Off schedule
Choose “Add Device”. In order to add more Devices lat-
set in your area. Shelly may turn on or off automatically This function requires an Internet connection. To use
er, use the app menu at the top right corner of the main
at sunrise/sunset, or at a specified time before or af- Internet, a Shelly Device has to be connected to a local
screen and click “Add Device”. Type the name (SSID) and
ter sunrise/sunset. This function requires an Internet WiFi network with working internet connection. Shelly
password for the WiFi network, to which you want to add
connection. To use Internet, a Shelly Device has to be may turn on/off automatically at a predefined time.
the Device.
connected to a local WiFi network with working internet
connection. Manufacturer: Allterco Robotics EOOD
Address: Sofia, 1407, 103 Cherni vrah Blvd.
Settings Tel.: +359 2 988 7435
• Power on default mode - Тhis setting controls whether E-mail: [email protected]
the Device will supply power or not the output as a de- The Declaration of Conformity is available at:
fault whenever it is receiving power from the grid: https://Shelly.cloud/declaration-of-conformity/
- ON: When the Device is powered, by default the sock- Changes in the contact data are published by the Manufacturer
et will be powered. at the official website of the Device: https://www.shelly.cloud
- OFF: Even if the Device is powered, by default the The User is obliged to stay informed for any amendments of
socket will not be powered. these warranty terms before exercising his/her rights against
Step 7 the Manufacturer.
• Restore last mode - When power is restored, by de-
To enable connection to the Shelly Cloud service for re- All rights to trademarks She® and Shelly® , and other intel-
fault, the appliance will return to the last state it was in
lectual rights associated with this Device belong to Allterco
mote control and monitoring of the Device, press “YES” before the last power off/shutdown. Robotics EOOD.
on the following pop-up. • Button Type
• Momentary - Set Shelly input to be buttons. Push for ATTENTION! If you have entered incorrect information
ON, push again for OFF. (wrong settings, usernames, passwords etc.), you will
• Toggle switch - Set Shelly input to be flip switches, with not be able to connect to Shelly and you have to reset
Step 3 • one state for ON and another state for OFF. the Device.
• Firmware update - Shows present firmware version. If WARNING! If you do not see an active WiFi network with
a newer version is available, you can update your Shelly SSID like shellyuni-35FA58, reset the Device. If the De-
Device by clicking Update. vice has been powered on, you have to restart by pow-
• Factory reset - Remove Shelly from your account and ering it off and on again. Power on shelly Uni and press
return it to its factory settings. the reset switch button until the LED on the board goes in
• Device information - Here you can see the unique ID of ON. If not, please repeat or contact our customer support
Shelly and the IP it got from the Wi-Fi network. at [email protected]
• Login - access to the Device
THE EMBEDDED WEB INTERFACE • Leave unprotected - removing the notification for dis-
Еven without the mobile app, Shelly can be set and con- abled authorization.
trolled through a browser and WiFi connection of a mo- • Enable authentication – you can turn authentication
bile phone, tablet or PC. on or off. This is where you can change your username
If using iOS (left screenshot) and password. You must enter a new username and the
Press the home button of your iPhone/iPad/iPod. Open Abbreviations used new password, then press Save to save the changes.
Settings > WiFi and connect to the WiFi network created • Shelly-ID – the unique name of the Device. It consists • Connect to cloud - you can turn the connection be-
by Shelly, e.g. shellyuni-35FA58. of 6 or more characters. It may include numbers and let- tween Shelly and Shelly Cloud on or off.
If using Android (right screenshot): your phone/tablet ters, for example 35FA58. • Factory reset - return Shelly to its factory settings.
will automatically scan and include all new Shelly Devic- • SSID – the name of the WiFi network, created by the • Firmware upgrade - Shows present firmware version.
es in the WiFi network that you are connected to. Shelly Device Settings Device, for example shellyuni-35FA58. If a newer version is available, you can update your Shelly
Upon successful Device Inclusion to the WiFi network After your Shelly device is included in the application, you • Access Point (AP) – the mode in which the Device cre- Device by clicking Update.
you will see the following pop-up can control it, change its settings and automate the way ates its own WiFi connection point with the respective • Device reboot - reboots the Device.
it works. To enter at the details menu of the respective name (SSID).
Device, simply click on it’s name. • Client Mode (CM) – the mode in which the Device is
connected to another WiFi network.
CHANNEL CONFIGURATION

Initial inclusion Channel Screen

In this screen you can control, monitor and change the
Step 1
settings for turning the power on and off. You can also
Install Shelly to the power grid following the schemes de-
see the current status of the connected appliance to
scribed above and place it into the console. After turning
Shelly, Buttons Settings, On and OFF. To control Shelly
the power on Shelly will create its own WiFi network (AP).
press Channel:
WARNING! If you do not see an active WiFi network with
• To turn on the connected circuit press “Turn ON”.
SSID like shellyuni-35FA58, reset the Device. If the De-
• To turn off the connected circuit press “Turn OFF”
vice has been powered on, you have to restart by pow-
• Press the icon to go to the previous menu.