Rectangular Tank Calculation Sheet

TANK CALCULATION SHEET

I. DESIGN PARAMETERS:

- Code Design : API 650 & Roark's Formulas

- Design pressure Pd : Full water + 5 kPag
= 34.43 kPa
- Design temperature : 60 oC / AMB
- Operating pressure : ATM
- Operating temperature : 27 oC
- Corrosion Allowance C.A : 0 mm
- Liquid Specific Gravity : 1.00
- Joint Efficiency : 0.85 (For Shell)
: 1.00 (For Roof & Bottom)
- Elastic Modulus E : 2.9*E+7 psi
= 199947962 kPa
retangular
MATERIAL SPECIFICATION: :
- Shell, Roof & Bottom : SS 316L
- Allowable Stress Sa : 16700 psi
= 115142 kPa
- Nozzle Neck : A 182 F 316L
- Flange : A 182 F 316L
- Pipe Fittings : A 312 TP 316L
- Bolts & Nuts : A 193 Gr B8M / A 194 Gr 8M
- Stiffeners : SS 316L

TANK GEOMETRY:
- Height H: 3000 mm
- Length L: 10000 mm
- Width W: 10000 mm
Height (H)

Width (W)

Page 1 of 53
Rectangular Tank Calculation Sheet

II. DESIGN
II.1 Side Wall Plate Calculation (Height x Length)
II.1.1 Wall Thickness Calculation
(As per Roark's Formulas 7Th Ed, Table 11.4 Case 1a)

b b b b

a
Height (H)

a
a
a
Length (L) Stiffeners

Vertical length without reinforced a: 750 mm

Horizontal length without reinforced b: 2500 mm
Ratio, a/b : 0.30
α = 0.0797
β = 0.4658
Required thickness
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 29.50 mm
Adopted thickness ta : 6.00 mm
Maximum deflection
Ymax = α*Pd*b4/(E*ta3) = 2481.90 mm
Ymax < 1/2 ta
2481.9mm < 3mm
Failed-Failed-Failed, The Tank need more stiffener

II.1.2 Top Edge Stiffener

R1 = 0.03*Pd*a = 0.77 kN/m

R2 = 0.32*Pd*a = 8.26 kN/m

Moment inertia required:

Jmin = R1*b4/(192*E*ta) = 131374.21 mm4
= 13.1374 cm4
Moment inertia of used stiffener (Flat bar 65x6):
Jx = Jy = 13.7 cm4
Therefore, Top edge stiffener is satisfactory

II.1.3 Horizontal Stiffener

Moment inertia required:
Jmin = R2*b4/(192*E*ta) = 1401324.90 mm4
= 140.1325 cm4
Moment inertia of used stiffener (Flat bar 65x6):
Jx = Jy = 13.7 cm4
Failed-Failed-Failed, The Tank need more stiffener

Page 2 of 53
Rectangular Tank Calculation Sheet

II.1.4 Vertical Stiffener

Maximum bending moment at Hy = 0.5773*amax = 432.98 mm

Maximum bending moment:

Mmax = 0.0641*Pd*b*Hy2 = 1.03 kNm
Required section modulus:
Zr = Mmax/Sa = 8.98E-06 mm3
= 8.98 cm3
Section modulus of used stiffener (Flat bar 65x6):
Z = 4.2 cm3
Failed-Failed-Failed, The Tank need more stiffener

II.2 Side Wall Plate Calculation (Height x Width)

II.2.1 Wall Thickness Calculation
(As per Roark's Formulas 7Th Ed, Table 11.4 Case 1a)

b b b b
a
a
Height (H)

a
a

Width (W) Stiffeners

Vertical length without reinforced a: 1000 mm

Horizontal length without reinforced b: 3333 mm
Ratio, a/b : 0.30
α = 0.0934
β = 0.5301
Required thickness
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 41.97 mm
Adopted thickness ta : 6.00 mm
Maximum deflection
Ymax = α*Pd*b4/(E*ta3) = 9192.38 mm
Ymax < 1/2 ta
9192.38mm < 3mm
Failed-Failed-Failed, The Tank need more stiffener

II.2.2 Top Edge Stiffener

R1 = 0.03*Pd*a = 1.03 kN/m

R2 = 0.32*Pd*a = 11.02 kN/m

Moment inertia required:

Jmin = R1*b4/(192*E*ta) = 553609.84 mm4
= 55.3610 cm4
Moment inertia of used stiffener (Flat bar 65x6):

Page 3 of 53
Rectangular Tank Calculation Sheet

Jx = Jy = 13.7 cm4
Failed-Failed-Failed, The Tank need more stiffener

II.2.3 Horizontal Stiffener

Moment inertia required:
Jmin = R2*b4/(192*E*ta) = 5905171.60 mm4
= 590.5172 cm4
Moment inertia of used stiffener (Flat bar 65x6):
Jx = Jy = 13.7 cm4
Failed-Failed-Failed, The Tank need more stiffener

II.2.4 Vertical Stiffener

Maximum bending moment at Hy = 0.5773*amax = 577.30 mm

Maximum bending moment:

Mmax = 0.0641*Pd*b*Hy2 = 2.45 kNm
Required section modulus:
Zr = Mmax/Sa = 2.13E-05 mm3
= 21.29 cm3
Section modulus of used stiffener (Flat bar 65x6):
Z = 4.2 cm3
Failed-Failed-Failed, The Tank need more stiffener

II.3 Roof Plate Calculation

b b
a
Width (W)

Length (L) Stiffeners

Loads on roof plate:

- Roof area: = 100 m2
- Live load: = 1.5 kPa
- Roof weight: = 4760 kg
- Roof structure weight: = 116 kg
- Roof Equipment weight: = 120 kg
- Dead load: = 0.5 kPa
Total load on roof plate: = 2.0 kPa

Distance without reinforced in width a: 5000 mm

Distance without reinforced in length b: 5000 mm
Ratio, a/b : 1.00
α = 0.0332
β = 0.2297
Required thickness:
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 9.96 mm

Page 4 of 53
Rectangular Tank Calculation Sheet

Adopted thickness ta : 6.00 mm

Maximum deflection:
Ymax = α*Pd*b4/(E*ta3) = 956.13 mm
Ymax < 1/2 ta
956.13mm < 3mm
Failed-Failed-Failed, The Tank need more stiffener

II.4 Bottom Plate Calculation

b b b b

a
a
Width (W)

a
a
Length (L) Stiffeners

Distance without reinforced in width a: 5000 mm

Distance without reinforced in length b: 5000 mm
Ratio, a/b : 1.00
α = 0.0332
β = 0.2297
Required thickness:
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 41.44 mm
Adopted thickness ta : 8.00 mm
Maximum deflection:
Ymax = α*Pd*b4/(E*ta3) = 6978.60 mm
Ymax < 1/2 ta
6978.6mm < 4mm
Failed-Failed-Failed, The Tank need more stiffener

Page 5 of 53
Rectangular Tank Calculation Sheet

Page 6 of 53
Rectangular Tank Calculation Sheet

Page 7 of 53
Rectangular Tank Calculation Sheet

Page 8 of 53
Rectangular Tank Calculation Sheet

Page 9 of 53
Rectangular Tank Calculation Sheet

Page 10 of 53
Rectangular Tank Calculation Sheet

Page 11 of 53
Rectangular Tank Calculation Sheet

Page 12 of 53
Rectangular Tank Calculation Sheet

TANK CALCULATION SHEET

I. DESIGN PARAMETERS:

- Code Design : API 650 & Roark's Formulas

- Design pressure Pd : Full water + 5 kPag
= 34.43 kPa
- Design temperature : 60 oC / AMB
- Operating pressure : ATM
- Operating temperature : 27 oC
- Corrosion Allowance C.A : 0 mm
- Liquid Specific Gravity : 1.00
- Joint Efficiency : 0.85 (For Shell)
: 1.00 (For Roof & Bottom)
- Elastic Modulus E : 2.9*E+7 psi
= 199947962 kPa
retangular
MATERIAL SPECIFICATION: :
- Shell, Roof & Bottom : SS 316L
- Allowable Stress Sa : 16700 psi
= 115142 kPa
- Nozzle Neck : A 182 F 316L
- Flange : A 182 F 316L
- Pipe Fittings : A 312 TP 316L
- Bolts & Nuts : A 193 Gr B8M / A 194 Gr 8M
- Stiffeners : SS 316L

TANK GEOMETRY:
- Height H: 3000 mm
- Length L: 10000 mm
- Width W: 10000 mm
Height (H)

Width (W)

Page 13 of 53
Rectangular Tank Calculation Sheet

Page 14 of 53
Rectangular Tank Calculation Sheet
II. DESIGN
II.1 Side Wall Plate Calculation (Height x Length)
II.1.1 Wall Thickness Calculation
(As per Roark's Formulas 7Th Ed, Table 11.4 Case 1a)

b b b b

a
Height (H)

a
a
a
Length (L) Stiffeners

Vertical length without reinforced a: 750 mm

Horizontal length without reinforced b: 2500 mm
Ratio, a/b : 0.30
α = 0.0504
β = 0.3185
Required thickness
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 24.40 mm
Adopted thickness ta : 8.00 mm
Maximum deflection
Ymax = α*Pd*b4/(E*ta3) = 662.13 mm
Ymax < 1/2 ta
662.13mm < 4mm
Failed-Failed-Failed, The Tank need more stiffener

II.1.2 Top Edge Stiffener

R1 = 0.03*Pd*a = 0.77 kN/m

R2 = 0.32*Pd*a = 8.26 kN/m

Moment inertia required:

Jmin = R1*b4/(192*E*ta) = 98530.66 mm4
= 9.8531 cm4
Moment inertia of used stiffener (angle 65x65x6):
Jx = Jy = 29.4 cm4
Therefore, Top edge stiffener is satisfactory

II.1.3 Horizontal Stiffener

Moment inertia required:
Jmin = R2*b4/(192*E*ta) = 1050993.68 mm4
= 105.0994 cm4
Moment inertia of used stiffener (angle 65x65x6):
Jx = Jy = 29.4 cm4
Failed-Failed-Failed, The Tank need more stiffener

Page 15 of 53
Rectangular Tank Calculation Sheet

Page 16 of 53
Rectangular Tank Calculation Sheet
II.1.4 Vertical Stiffener
Maximum bending moment at Hy = 0.5773*amax = 432.98 mm

Maximum bending moment:

Mmax = 0.0641*Pd*b*Hy2 = 1.03 kNm
Required section modulus:
Zr = Mmax/Sa = 8.98E-06 mm3
= 8.98 cm3
Section modulus of used stiffener (angle 65x65x6):
Z = 6.26 cm3
Failed-Failed-Failed, The Tank need more stiffener

II.2 Side Wall Plate Calculation (Height x Width)

II.2.1 Wall Thickness Calculation
(As per Roark's Formulas 7Th Ed, Table 11.4 Case 1a)

b b b b

a
a
Height (H)

a
a

Width (W) Stiffeners

Vertical length without reinforced a: 1000 mm

Horizontal length without reinforced b: 5000 mm
Ratio, a/b : 0.20
α = 0.0624
β = 0.38
Required thickness
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 53.30 mm
Adopted thickness ta : 8.00 mm
Maximum deflection
Ymax = α*Pd*b4/(E*ta3) = 13116.40 mm
Ymax < 1/2 ta
13116.4mm < 4mm
Failed-Failed-Failed, The Tank need more stiffener

II.2.2 Top Edge Stiffener

R1 = 0.03*Pd*a = 1.03 kN/m

R2 = 0.32*Pd*a = 11.02 kN/m

Moment inertia required:

Jmin = R1*b4/(192*E*ta) = 2101987.35 mm4
= 210.1987 cm4
Moment inertia of used stiffener (angle 65x65x6):
Jx = Jy = 29.4 cm4
Failed-Failed-Failed, The Tank need more stiffener

Page 17 of 53
Rectangular Tank Calculation Sheet

II.2.3 Horizontal Stiffener

Moment inertia required:
Jmin = R2*b4/(192*E*ta) = 22421198.41 mm4
= 2242.1198 cm4
Moment inertia of used stiffener (angle 65x65x6):
Jx = Jy = 29.4 cm4
Failed-Failed-Failed, The Tank need more stiffener

II.2.4 Vertical Stiffener

Maximum bending moment at Hy = 0.5773*amax = 577.30 mm

Maximum bending moment:

Mmax = 0.0641*Pd*b*Hy2 = 3.68 kNm
Required section modulus:
Zr = Mmax/Sa = 3.19E-05 mm3
= 31.94 cm3
Section modulus of used stiffener (angle 65x65x6):
Z = 6.26 cm3
Failed-Failed-Failed, The Tank need more stiffener

II.3 Roof Plate Calculation

b b
a
Width (W)

Length (L) Stiffeners

Loads on roof plate:

- Roof area: = 100 m2
- Live load: = 1.5 kPa
- Roof weight: = 4760 kg
- Roof structure weight: = 116 kg
- Roof Equipment weight: = 120 kg
- Dead load: = 0.5 kPa
Total load on roof plate: = 2.0 kPa

Distance without reinforced in width a: 10000 mm

Distance without reinforced in length b: 1250 mm
Ratio, a/b : 8.00
α = 0.0886
β = 0.5076
Required thickness:
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 3.70 mm
Adopted thickness ta : 6.00 mm
Maximum deflection:
Ymax = α*Pd*b4/(E*ta3) = 9.97 mm

Page 18 of 53
Rectangular Tank Calculation Sheet

Ymax < 1/2 ta

9.97mm < 3mm
Failed-Failed-Failed, The Tank need more stiffener

Page 19 of 53
Rectangular Tank Calculation Sheet
II.4 Bottom Plate Calculation

b b b b

a
a
Width (W)

a
a
Length (L) Stiffeners

Distance without reinforced in width a: 5000 mm

Distance without reinforced in length b: 1111 mm
Ratio, a/b : 4.50
α = 0.0341
β = 0.2341
Required thickness:
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 9.30 mm
Adopted thickness ta : 8.00 mm
Maximum deflection:
Ymax = α*Pd*b4/(E*ta3) = 17.48 mm
Ymax < 1/2 ta
17.48mm < 4mm
Failed-Failed-Failed, The Tank need more stiffener

Page 20 of 53
Rectangular Tank Calculation Sheet

Page 21 of 53
Rectangular Tank Calculation Sheet

Page 22 of 53
Rectangular Tank Calculation Sheet

Page 23 of 53
Rectangular Tank Calculation Sheet

Page 24 of 53
Rectangular Tank Calculation Sheet

Page 25 of 53
Rectangular Tank Calculation Sheet

Page 26 of 53
Rectangular Tank Calculation Sheet

Page 27 of 53
Rectangular Tank Calculation Sheet

Page 28 of 53
Rectangular Tank Calculation Sheet

Page 29 of 53
Rectangular Tank Calculation Sheet

Page 30 of 53
Rectangular Tank Calculation Sheet

TANK CALCULATION SHEET

I. DESIGN PARAMETERS:

- Code Design : API 650 & Roark's Formulas

- Design pressure Pd : Full water + 5 kPag
= 24.62 kPa
- Design temperature : 60 oC / AMB
- Operating pressure : ATM
- Operating temperature : 27 oC
- Corrosion Allowance C.A : 0 mm
- Liquid Specific Gravity : 1.00
- Joint Efficiency : 0.85 (For Shell)
: 1.00 (For Roof & Bottom)
- Elastic Modulus E : 2.9*E+7 psi
= 199947962 kPa
retangular
MATERIAL SPECIFICATION: :
- Shell, Roof & Bottom : SS 316L
- Allowable Stress Sa : 16700 psi
= 115142 kPa
- Nozzle Neck : A 182 F 316L
- Flange : A 182 F 316L
- Pipe Fittings : A 312 TP 316L
- Bolts & Nuts : A 193 Gr B8M / A 194 Gr 8M
- Stiffeners : SS 316L

TANK GEOMETRY:
- Height H: 2000 mm
- Length L: 5700 mm
- Width W: 1250 mm
Height (H)

Width (W)

Page 31 of 53
Rectangular Tank Calculation Sheet

Page 32 of 53
Rectangular Tank Calculation Sheet
II. DESIGN
II.1 Side Wall Plate Calculation (Height x Length)
II.1.1 Wall Thickness Calculation
(As per Roark's Formulas 7Th Ed, Table 11.4 Case 1a)

b b b b

a
a
Height (H)

a
a
Length (L) Stiffeners

Vertical length without reinforced a: 667 mm

Horizontal length without reinforced b: 633 mm
Ratio, a/b : 1.05
α = 0.0487
β = 0.3096
Required thickness
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 5.15 mm
Adopted thickness ta : 8.00 mm
Maximum deflection
Ymax = α*Pd*b4/(E*ta3) = 1.88 mm
Ymax < 1/2 ta
1.88mm < 4mm
Therefore, adopted thickness is satisfactory

II.1.2 Top Edge Stiffener

R1 = 0.03*Pd*a = 0.49 kN/m

R2 = 0.32*Pd*a = 5.25 kN/m

Moment inertia required:

Jmin = R1*b4/(192*E*ta) = 257.95 mm4
= 0.0258 cm4
Moment inertia of used stiffener (angle 65x65x6):
Jx = Jy = 29.4 cm4
Therefore, Top edge stiffener is satisfactory

II.1.3 Horizontal Stiffener

Moment inertia required:
Jmin = R2*b4/(192*E*ta) = 2751.49 mm4
= 0.2751 cm4
Moment inertia of used stiffener (angle 65x65x6):
Jx = Jy = 29.4 cm4
Therefore, Horizontal stiffener is satisfactory

Page 33 of 53
Rectangular Tank Calculation Sheet

Page 34 of 53
Rectangular Tank Calculation Sheet
II.1.4 Vertical Stiffener
Maximum bending moment at Hy = 0.5773*amax = 384.87 mm

Maximum bending moment:

Mmax = 0.0641*Pd*b*Hy2 = 0.15 kNm
Required section modulus:
Zr = Mmax/Sa = 1.29E-06 mm3
= 1.29 cm3
Section modulus of used stiffener (angle 65x65x6):
Z = 6.26 cm3
Therefore, Vertical stiffener is satisfactory

II.2 Side Wall Plate Calculation (Height x Width)

II.2.1 Wall Thickness Calculation
(As per Roark's Formulas 7Th Ed, Table 11.4 Case 1a)

b b b b

a
a
Height (H)

a
a

Width (W) Stiffeners

Vertical length without reinforced a: 667 mm

Horizontal length without reinforced b: 625 mm
Ratio, a/b : 1.07
α = 0.0504
β = 0.3185
Required thickness
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 5.16 mm
Adopted thickness ta : 8.00 mm
Maximum deflection
Ymax = α*Pd*b4/(E*ta3) = 1.85 mm
Ymax < 1/2 ta
1.85mm < 4mm
Therefore, adopted thickness is satisfactory

II.2.2 Top Edge Stiffener

R1 = 0.03*Pd*a = 0.49 kN/m

R2 = 0.32*Pd*a = 5.25 kN/m

Moment inertia required:

Jmin = R1*b4/(192*E*ta) = 244.64 mm4
= 0.0245 cm4
Moment inertia of used stiffener (angle 65x65x6):
Jx = Jy = 29.4 cm4
Therefore, Top edge stiffener is satisfactory

Page 35 of 53
Rectangular Tank Calculation Sheet

II.2.3 Horizontal Stiffener

Moment inertia required:
Jmin = R2*b4/(192*E*ta) = 2609.51 mm4
= 0.2610 cm4
Moment inertia of used stiffener (angle 65x65x6):
Jx = Jy = 29.4 cm4
Therefore, Horizontal stiffener is satisfactory

II.2.4 Vertical Stiffener

Maximum bending moment at Hy = 0.5773*amax = 384.87 mm

Maximum bending moment:

Mmax = 0.0641*Pd*b*Hy2 = 0.15 kNm
Required section modulus:
Zr = Mmax/Sa = 1.27E-06 mm3
= 1.27 cm3
Section modulus of used stiffener (angle 65x65x6):
Z = 6.26 cm3
Therefore, Vertical stiffener is satisfactory

II.3 Roof Plate Calculation

b b
a
(W)
Width

Length (L) Stiffeners

Loads on roof plate:

- Roof area: = 7.125 m2
- Live load: = 1.5 kPa
- Roof weight: = 386 kg
- Roof structure weight: = 116 kg
- Roof Equipment weight: = 120 kg
- Dead load: = 0.9 kPa
Total load on roof plate: = 2.4 kPa

Distance without reinforced in width a: 1250 mm

Distance without reinforced in length b: 712.5 mm
Ratio, a/b : 1.75
α = 0.0989
β = 0.5559
Required thickness:
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 2.40 mm
Adopted thickness ta : 6.00 mm
Maximum deflection:
Ymax = α*Pd*b4/(E*ta3) = 1.39 mm

Page 36 of 53
Rectangular Tank Calculation Sheet

Ymax < 1/2 ta

1.39mm < 3mm
Therefore, adopted thickness is satisfactory

Page 37 of 53
Rectangular Tank Calculation Sheet
II.4 Bottom Plate Calculation

b b b b

a
a
Width (W)

a
a
Length (L) Stiffeners

Distance without reinforced in width a: 625 mm

Distance without reinforced in length b: 633 mm
Ratio, a/b : 0.99
α = 0.0435
β = 0.283
Required thickness:
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 4.93 mm
Adopted thickness ta : 8.00 mm
Maximum deflection:
Ymax = α*Pd*b4/(E*ta3) = 1.68 mm
Ymax < 1/2 ta
1.68mm < 4mm
Therefore, adopted thickness is satisfactory

Page 38 of 53
Rectangular Tank Calculation Sheet

Page 39 of 53
Rectangular Tank Calculation Sheet

TANK CALCULATION SHEET

I. DESIGN PARAMETERS:

- Code Design : API 650 & Roark's Formulas

- Design pressure Pd : Full water + 5 kPag
= 24.62 kPa
- Design temperature : 60 oC / AMB
- Operating pressure : ATM
- Operating temperature : 27 oC
- Corrosion Allowance C.A : 0 mm
- Liquid Specific Gravity : 1.00
- Joint Efficiency : 0.85 (For Shell)
: 1.00 (For Roof & Bottom)
- Elastic Modulus E : 2.9*E+7 psi
= 199947962 kPa
retangular
MATERIAL SPECIFICATION: :
- Shell, Roof & Bottom : SS 316L
- Allowable Stress Sa : 16700 psi
= 115142 kPa
- Nozzle Neck : A 182 F 316L
- Flange : A 182 F 316L
- Pipe Fittings : A 312 TP 316L
- Bolts & Nuts : A 193 Gr B8M / A 194 Gr 8M
- Stiffeners : SS 316L

TANK GEOMETRY:
- Height H: 2000 mm
- Length L: 2100 mm
- Width W: 1250 mm
Height (H)

Width (W)

Page 40 of 53
Rectangular Tank Calculation Sheet

II. DESIGN
II.1 Side Wall Plate Calculation (Height x Length)
II.1.1 Wall Thickness Calculation
(As per Roark's Formulas 7Th Ed, Table 11.4 Case 1a)

b b b b

a
a
Height (H)

a
a
Length (L) Stiffeners

Vertical length without reinforced a: 500.0 mm

Horizontal length without reinforced b: 525 mm
Ratio, a/b : 0.95
α = 0.0401
β = 0.2652
Required thickness
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 3.95 mm
Adopted thickness ta : 6.00 mm
Maximum deflection
Ymax = α*Pd*b4/(E*ta3) = 1.74 mm
Ymax < 1/2 ta
1.74mm < 3mm
Therefore, adopted thickness is satisfactory

II.1.2 Top Edge Stiffener

R1 = 0.03*Pd*a = 0.37 kN/m

R2 = 0.32*Pd*a = 3.94 kN/m

Moment inertia required:

Jmin = R1*b4/(192*E*ta) = 121.80 mm4
= 0.0122 cm4
Moment inertia of used stiffener (Flat bar 65x6):
Jx = Jy = 13.7 cm4
Therefore, Top edge stiffener is satisfactory

II.1.3 Horizontal Stiffener

Moment inertia required:
Jmin = R2*b4/(192*E*ta) = 1299.20 mm4
= 0.1299 cm4
Moment inertia of used stiffener (Flat bar 65x6):
Jx = Jy = 13.7 cm4
Therefore, Horizontal stiffener is satisfactory

Page 41 of 53
Rectangular Tank Calculation Sheet

II.1.4 Vertical Stiffener

Maximum bending moment at Hy = 0.5773*amax = 288.65 mm

Maximum bending moment:

Mmax = 0.0641*Pd*b*Hy2 = 0.07 kNm
Required section modulus:
Zr = Mmax/Sa = 6.00E-07 mm3
= 0.60 cm3
Section modulus of used stiffener (Flat bar 65x6):
Z = 4.2 cm3
Therefore, Vertical stiffener is satisfactory

II.2 Side Wall Plate Calculation (Height x Width)

II.2.1 Wall Thickness Calculation
(As per Roark's Formulas 7Th Ed, Table 11.4 Case 1a)

b b b b
a
a
Height (H)

a
a

Width (W) Stiffeners

Vertical length without reinforced a: 500 mm

Horizontal length without reinforced b: 417 mm
Ratio, a/b : 1.20
α = 0.0616
β = 0.3762
Required thickness
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 3.74 mm
Adopted thickness ta : 6.00 mm
Maximum deflection
Ymax = α*Pd*b4/(E*ta3) = 1.06 mm
Ymax < 1/2 ta
1.06mm < 3mm
Therefore, adopted thickness is satisfactory

II.2.2 Top Edge Stiffener

R1 = 0.03*Pd*a = 0.37 kN/m

R2 = 0.32*Pd*a = 3.94 kN/m

Moment inertia required:

Jmin = R1*b4/(192*E*ta) = 48.32 mm4
= 0.0048 cm4
Moment inertia of used stiffener (Flat bar 65x6):

Page 42 of 53
Rectangular Tank Calculation Sheet

Jx = Jy = 13.7 cm4
Therefore, Top edge stiffener is satisfactory

II.2.3 Horizontal Stiffener

Moment inertia required:
Jmin = R2*b4/(192*E*ta) = 515.46 mm4
= 0.0515 cm4
Moment inertia of used stiffener (Flat bar 65x6):
Jx = Jy = 13.7 cm4
Therefore, Horizontal stiffener is satisfactory

II.2.4 Vertical Stiffener

Maximum bending moment at Hy = 0.5773*amax = 288.65 mm

Maximum bending moment:

Mmax = 0.0641*Pd*b*Hy2 = 0.05 kNm
Required section modulus:
Zr = Mmax/Sa = 4.76E-07 mm3
= 0.48 cm3
Section modulus of used stiffener (Flat bar 65x6):
Z = 4.2 cm3
Therefore, Vertical stiffener is satisfactory

II.3 Roof Plate Calculation

b b
a
(W)
Width

Length (L) Stiffeners

Loads on roof plate:

- Roof area: = 2.625 m2
- Live load: = 1.5 kPa
- Roof weight: = 174 kg
- Roof structure weight: = 116 kg
- Roof Equipment weight: = 120 kg
- Dead load: = 1.5 kPa
Total load on roof plate: = 3.0 kPa

Distance without reinforced in width a: 1250 mm

Distance without reinforced in length b: 700 mm
Ratio, a/b : 1.79
α = 0.1011
β = 0.5662
Required thickness:
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 2.70 mm

Page 43 of 53
Rectangular Tank Calculation Sheet

Adopted thickness ta : 6.00 mm

Maximum deflection:
Ymax = α*Pd*b4/(E*ta3) = 1.70 mm
Ymax < 1/2 ta
1.7mm < 3mm
Therefore, adopted thickness is satisfactory

II.4 Bottom Plate Calculation

b b b b

a
a
Width (W)

a
a
Length (L) Stiffeners

Distance without reinforced in width a: 625 mm

Distance without reinforced in length b: 525 mm
Ratio, a/b : 1.19
α = 0.0607
β = 0.3718
Required thickness:
tr = Sqrt(β*Pd*b2)/Sa) + C.A = 4.68 mm
Adopted thickness ta : 8.00 mm
Maximum deflection:
Ymax = α*Pd*b4/(E*ta3) = 1.11 mm
Ymax < 1/2 ta
1.11mm < 4mm
Therefore, adopted thickness is satisfactory

Page 44 of 53
Rectangular Tank Calculation Sheet

Page 45 of 53
THANG LONG
 DESIGN CAPACITY LENGTH WIDTH HEIGHT
ITEM NO. NAME (m3) (mm) (mm) (mm)
T-6601 CORROSION INHIBITOR TANK 2.22 1219 1066 1760
T-6603 POUR POINT DEPRESSANT TANK 12.02 5600 1100 2000
T-6605 BACK UP CHEMICAL TANK 2.22 1219 1066 1760
T-6607 DEMULSIFIER TANK 2.22 1219 1066 1760
DONG DO
T-6621 CORROSION INHIBITOR TANK 2.22 1219 1066 1760
T-6622 POUR POINT DEPRESSANT TANK 13.93 5700 1250 2000
T-6623 DEMULSIFIER TANK 2.22 1219 1066 1760
T-6624 H2S SCAVENGER TANK 5.13 2100 1250 2000
T-6629 BACK UP CHEMICAL TANK 2.22 1219 1066 1760
T-6636 SCALE INHIBITOR TANK 2.22 1219 1066 1760
HEIGHT X LENGTH HEIGHT X WIDTH ROOF PLATE BOTTOM PLATE
 t a b t a b t a b t a b
(mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)

6 587 406 6 587 355 6 533 609.5 8 533 609.5

8 667 700 8 667 550 6 1100 700 8 550 700
6 587 406 6 587 355 6 533 609.5 8 533 609.5
6 587 406 6 587 355 6 533 609.5 8 533 609.5

6 587 406 6 587 355 6 533 609.5 8 533 609.5

8 667 712.5 8 667 625 6 1250 712.5 8 625 712.5
6 587 406 6 587 355 6 533 609.5 8 533 609.5
6 500 525 6 500 417 6 1250 700 8 625 700
6 587 406 6 587 355 6 533 609.5 8 533 609.5
6 587 406 6 587 355 6 533 609.5 8 533 609.5
 A(L) A(U) binh tang cung Base specific
mw nozz accessary dry
(mm2) (mm2) (kg) (kg) frame gravity

4 4 4 4 3 3 3 3 390 1160 517 119 63 20 20 53 792 0.99

4 10 4 3 2 9 3 10 753 1160 2344 766 63 20 20 144 3357 0.91
4 4 4 4 3 3 3 3 390 1160 517 119 63 20 20 53 792 0.781
4 4 4 4 3 3 3 3 390 1160 517 119 63 20 20 53 792 1.02

4 4 4 4 3 3 3 3 390 1160 517 119 63 20 20 53 792 0.99

4 10 4 3 2 9 3 10 753 1160 2513 776 63 20 20 148 3541 0.91
4 4 4 4 3 3 3 3 390 1160 517 119 63 20 20 53 792 1.02
5 5 5 4 2 4 3 5 390 1160 913 195 63 20 20 77 1289 0.998
4 4 4 4 3 3 3 3 390 1160 517 119 63 20 20 53 792 0.78
4 4 4 4 3 3 3 3 390 1160 517 119 63 20 20 53 792 1.3
capacity luu chat hydro
operating
working (kg) test

2 1980 2772 3013

10.85 9873.5 13231 15379
2 1562 2354 3013
2 2040 2832 3013

2 1980 2772 3013

12.63 11493.3 15034 17471
2 2040 2832 3013
4.6 4590.8 5879 6422
2 1560 2352 3013
2 2600 3392 3013