EOCR-SSD

Digital Type Standard Over-current Relay with Ammeter

■ Introduction ■ Feature
ㆍProtection functions
Protection Operation time Condition
Over Preset O-Time
current
Phase-loss In 3 sec
Within 0.5sec In case that OC keeps
Locked after preset D- more than 200% after D-
Rotor time elapsed time elapsed

ㆍOver-current range ; 05Type : 0.5~6A

30Type : 3A~30A
60Type : 10A~60A
ㆍIndicates Trip cause
ㆍmanual(instant)/ electrical(remote) Reset
ㆍSingle phase(1P) / Three phase(3P) Selectable
※Terminal Diagram
ㆍRelay Output selectable – Fail safe(N) / Non-fail safe(R)

■ Typical Diagram

1 Definite-Time Characteristic of OC
■ Dimension
■ Specification
Over-current 05 0.5~6A
30 3~30A
Current Setting range 60 10~60A
Starting Delay time D-time 1~30sec
Operating Delay time O-time 0.5/1~10sec
Reset Manual (instant) / electrical Reset
Operating time Over current Definite time
Characteristic
Tolerance Current ±5% Time ±0.2sec
Environment Temperature Operation -20℃~60℃
Storage -30℃~80℃
Humidity 30~85% RH Non-Condensing
Power supply ㆍ 220 : 220VAC±15%, 50/60Hz
ㆍ 110 : 110VAC±15%, 50/60Hz
ㆍ 24 : 24VAC/DC
Output Relay 2-SPST(1a1b) 3A/250VAC, Resistive
Insulation Between casing and circuit 10MΩ, 500VDC
Dielectric Strength Between Casing & 2.0kV 60Hz, 1min
Circuits
Between Contacts 1.0kV 60Hz, 1min
Between Circuits 2.0kV 60Hz, 1min
Mounting 35mm Din Rail or Panel Mounting
Power Consumption Less than 3W
Electrostatic Discharge IEC61000-4-2 Level 3 : Air Discharge : ±8kV,
Contact Discharge : ±6kV
Radiated IEC61000-4-3 Level 3 : 10V/m, 150MHz & 450MHz
Electromagnetic Field Portable transceiver
Disturbance
EFT/Burst IEC61000-4-4 Level 3 : ±2kV, 1min
Surge IEC61000-4-5 Level 3 : 1.2X50µs, ±4kV(0°,90°,180°,270°)
1MHz Burst IEC61000-4-12 Level 3 : 2.5kV, 1MHz
disturbance
Conducted Emission IEC60255-25 Class A (Conducted & Radiated)

■ Trip display
LED
Trip Cause Description
Indication
Over Tripped after sensing over-current 10A
Current during operation.

Phase loss of L1(R)

Phase Loss Phase loss of L2(S)

Phase loss of L3(T)

Locked Tripped after sensing Locked Rotor during

Rotor starting.
■ How to set
Please Set before motor starting below.
1) Over-current : Set the rated motor current of its name plate . For protection of connected machinery with motor, it is
recommended to set the 110~115% of real running current after motor current is stabilized.
2) Starting Delay Time : Set the expected run-up time of motor by D-time Knob
3) Operating Time : Set trip delay time(O-time knob) to desired trip time.

Order Item Setting range FND DESCRIPTION

· Able to set current, preset, operating 0.5A.
05 Type : 0.5A~6A · 0.5~6A : set by step of 0.1A,
Over-current
1 30 Type : 3~30A
Setting · 3~30A : set by step of 1A
60 Type : 10A~60A
· 10~60A : set by step of 1A
Starting delay
2 time 0.5 ~ 30 sec
Setting
Operating
3 Time delay 0.5 ~ 30 sec
Setting
Display END after
4 TEST elapsing 3 sec+preset O-Time
3sec+preset O-time Cannot do a test during driving.

■ Odering

Model name 1 2 3 Accessory

E O C R S S D - 0 5 M 7 B 2CT-D-100

1 2 3
Current Range Power supply Frequency Mounting
EOCRSSD-05M7B 05 Type 05 220VAC M 50/60Hz 7 P/D Both B
EOCRSSD-30M7B 30 Type 30 P: Panel
EOCRSSD-60M7B 60 Type 60 D: Din Rail
EOCRSSD-05F7B 05 Type 05 110VAC F
EOCRSSD-30F7B 30 Type 30
EOCRSSD-60F7B 60 Type 60
EOCRSSD-05B7B 05 Type 05 24VAC/DC B
EOCRSSD-30B7B 30 Type 30
EOCRSSD-60B7B 60 Type 60

100:5 D1
150:5 DH ※ In case of combination with external CT
200:5 D2
300:5 D3 Ring CT Type inscribes like as R1, RH, R2…R4
400:5 D4 SRCT Type inscribes like as S1, SH, S2..S4

Accessory
2CT Ratio RCT Ratio SRCT Ratio
2CT-D-100 100:5 RCT-100 100:5 SR-2CT-100 100:5
2CT-D-150 150:5 RCT-150 150:5 SR-2CT-150 150:5
2CT-D-200 2CT - D - 200:5 RCT-200 RCT - 200:5 SR-2CT-200 SR - 2CT - 200:5
2CT-D-300 300:5 RCT-300 300:5 SR-2CT-300 300:5
2CT-D-400 400:5 RCT-400 400:5 SR-2CT-400 400:5