Scribd
Upload
4 views

Arduino Air Quality Monitor

This document defines code for an Arduino project that monitors air quality and temperature/humidity using sensors. It includes functions to read sensors, display readings on an OLED display, and classify the air quality reading into categories. The code initializes the sensors and display at startup and then continuously reads sensors, displays the readings, and refreshes the display in the main loop.

Uploaded by

Sandip
Copyright
© © All Rights Reserved
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
4 views

Arduino Air Quality Monitor

This document defines code for an Arduino project that monitors air quality and temperature/humidity using sensors. It includes functions to read sensors, display readings on an OLED display, and classify the air quality reading into categories. The code initializes the sensors and display at startup and then continuously reads sensors, displays the readings, and refreshes the display in the main loop.

Uploaded by

Sandip
Copyright
© © All Rights Reserved
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

#include <SPI.

h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
#include <Fonts/FreeSans9pt7b.h>
#include <Fonts/FreeMonoOblique9pt7b.h>
#include <DHT.h>
#define SCREEN_WIDTH 128 // OLED display width, in pixels
#define SCREEN_HEIGHT 64 // OLED display height, in pixels

#define OLED_RESET 4 // Reset pin # (or -1 if sharing Arduino reset pin)


Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET);

#define sensor A0
#define DHTPIN 2 // Digital pin 2
#define DHTTYPE DHT11 // DHT 11

int gasLevel = 0; //int variable for gas level


String quality ="";
DHT dht(DHTPIN, DHTTYPE);

void sendSensor()
{
float h = dht.readHumidity();
float t = dht.readTemperature();

if (isnan(h) || isnan(t)) {
Serial.println("Failed to read from DHT sensor!");
return;
}
display.setTextColor(WHITE);
display.setTextSize(1);
display.setFont();
display.setCursor(0, 43);
display.println("Temp :");
display.setCursor(80, 43);
display.println(t);
display.setCursor(114, 43);
display.println("C");
display.setCursor(0, 56);
display.println("RH :");
display.setCursor(80, 56);
display.println(h);
display.setCursor(114, 56);
display.println("%");
}

void air_sensor()
{
gasLevel = analogRead(sensor);

if(gasLevel<181){
quality = " GOOD!";
}
else if (gasLevel >181 && gasLevel<225){
quality = " Poor!";
}
else if (gasLevel >225 && gasLevel<300){
quality = "Very bad!";
}
else if (gasLevel >300 && gasLevel<350){
quality = "ur dead!";
}
else{
quality = " Toxic";
}

display.setTextColor(WHITE);
display.setTextSize(1);
display.setCursor(1,5);
display.setFont();
display.println("Air Quality:");
display.setTextSize(1);
display.setCursor(20,23);
display.setFont(&FreeMonoOblique9pt7b);
display.println(quality);
}

void setup() {
Serial.begin(9600);
pinMode(sensor,INPUT);
dht.begin();
if(!display.begin(SSD1306_SWITCHCAPVCC, 0x3c)) { // Address 0x3D for 128x64
Serial.println(F("SSD1306 allocation failed"));
}
display.clearDisplay();
display.setTextColor(WHITE);

display.setTextSize(2);
display.setCursor(50, 0);
display.println("Air");
display.setTextSize(1);
display.setCursor(23, 20);
display.println("Qulaity monitor");
display.display();
delay(1200);
display.clearDisplay();

display.setTextSize(2);
display.setCursor(20, 20);
display.println("BY Abid");
display.display();
delay(1000);
display.clearDisplay();
}

void loop() {
display.clearDisplay();
air_sensor();
sendSensor();
display.display();
}

You might also like