Renewable Lubricants™, Inc.

476 Griggy Rd. NE, PO Box 474

Hartville, OH 44632-0474
Voice: 330.877.9982 Fax: 330.877.2266
www.renewablelube.com

Bio-Ultimax™ 1500 Dielectric

Hydraulic Fluids
AW ISO 22, 32, 46, 68
"Biobased Lubricants that Perform Like Synthetics"
Bio-Ultimax™ 1500 Dielectric Hydraulic Fluids are ultimately biodegradable1 biosynthetic formulas that were designed
specifically for use in hydraulic equipment operating over a wide range of temperatures and where an oil with high dielectric
(>35 kV) insulating property is required. Applications include power utility aerial buckets, mobile or stationary hydraulic
systems, or other equipment were electrical insulating safety is preferred. These patented biobased hydraulic fluids are
formulated to perform in high and low pressure hydraulic systems that require Anti-Wear (AW), anti-rust, anti-oxidation, anti-
foam, and demulsibility properties. They are highly inhibited against moisture and rusting in both fresh and sea water and pass A
and B Sequences of the ASTM D-665 Turbine Oil Rust Test. Incorporating the super high viscosity index (VI) of the Stabilized*
High Oleic Base Stocks (HOBS) into the formulas, increases the viscosity index past synthetic levels (Energy Conserving
Formulas). The super high viscosity index of the HOBS naturally improves the thermal shear stability of the formula and
increases load capacity. They provide additional fluid value at the higher temperatures, which is a performance benefit over lower
VI products of the same ISO viscosity. The HOBS’s extremely low volatility increases the flash and fire safety features in the
formula. They are formulated to provide seal conditioning for longer seal life and to reduce oil leakage from the system. They
are compatible with the same seals, filters, materials and components that are designed to operate on petroleum oil based
formulations. An environmentally friendly, zinc-free additive system has also been developed that meets or exceeds high
pressure pump requirements.
Bio-Ultimax™ Hydraulic Fluids have a long-term history of proven performance with over 15 years of successfully being used in
a wide variety of stationary and mobile hydraulic equipment. These patented super high VI fluids have performed successfully in
hydraulic systems up to 10,000 psi and in systems with ultra-fine filtration. They are designed for use in hydraulic vane, piston,
and gear-type pumps that require DIN 51524 Part 2 and 3 (HLP/HVLP), Parker-Denison HF-O/T6H20C, HF-1, HF-2, Eaton-
Vickers M-2950-S (35VQ-25) and I-286-S (V-104C), Rexroth, Sauer-Sundstrand, GM (LS-2), US Steel 126, 136, and 127. They
also meet the requirements for ashless API GL-1, GL-2, GL-3, DIN 51517 Part 3, and AGMA Non-EP gear oils for bearing,
reduction units, and gear sets where they meet the viscosity ranges. They have shown to have exceptional anti-wear performance
in ASTM D-4172 Four Ball Wear Tests. Very little wear was encountered in the field studies, and in accelerated pump tests
using biobased formulations in Denison T-5D, Vickers 20VQ, 35VQ-25 (M-2950-S), and V-104C (ASTM D-2882), Vickers
I-286-S pump stand tests at pressures and temperatures ranging from 2000 to 3000 psi and from 1500 to 2100 F. Their
anti-wear performance exceeds the requirements for GM (LS-2), US Steel 126, 136 127, and load stage 10 in the FZG (DIN
51354). Bio-Ultimax™ Hydraulic Fluids meets and exceeds Federal Specifications A-A-59354 Superseding MIL-H-46001D
Specification for machine tool hydraulic systems.
Bio-Ultimax™ 1500 Hydraulic Fluids meet the Environmental Protection Agency (EPA) 2013 Vessel General Permit (VGP)
guidelines for Environmentally Acceptable Lubricants (EALs), and should be used in hydraulic systems where LOW
TOXICITY, BIODEGRADABILITY and NON-BIOACCUMULATION properties are required. They exceed the acute
toxicity (LC-50 / EC-50 >1000 ppm) criteria adopted by the US Fish and Wildlife Service and the US EPA. Because they meet
the environmental requirements they can also be used where ISO 15380 HEES/HETG Hydraulic Fluids are specified. Bio-
Ultimax™ Hydraulic Fluids are ENVIRONMENTALLY ACCEPTED LUBRICANTS (EALs) that are formulated from
renewable biobased resources. We believe Earth's environmental future rests in the use of renewable materials.
1Ultimate/Readily
Biodegradation (Pw1) within 28 days in ASTM D-5864 Aerobic Aquatic Biodegradation of
Lubricants
STABILIZED by Renewable Lubricants™* is RLI’s trademark on their proprietary and patented anti-oxidant, anti-wear, and cold flow technology. High Oleic Base
Stock (HOBS) are agricultural vegetable oils. This Stabilized technology allows the HOBS to perform as a high performance formula in high and low temperature
applications, reducing oil thickening and deposits. Patented Product: US Patent 6,383,992, US Patent 6,534,454 with additional Pending and Foreign Patents
™ Trademark of Renewable Lubricants™, Inc. Copyright 1999 Renewable Lubricants, Inc.

Availability F.O.B. :Hartville, Ohio, USA 1 Gallon 5 Gallon Pail Drum Totes Bulk
 Bio-Ultimax™ 1500 Dielectric Hydraulic Fluid ISO 22, 32, 46, 68
The test data below show that the Bio-Ultimax™ 1500 Dielectric Hydraulic Fluids provide high performance in a wide variety of stationary and transportation equipment,
that operate in broad ranges of environmental conditions. In equipment operating outside, wear from poor cold temperature pumpability, surge loads, moisture, and dusty
environments are more prominent. Bio-Ultimax™ 1500 Dielectric Hydraulic Fluids are formulated to improve performance in equipment that requires excellent anti-
wear, demulsibility, and cold temperature pumpability as low as -400C. They meet and exceed ISO 11158 HV and have Genie-Terex and Altec Equipment OEM
approvals.

TYPICAL METHOD ISO 22 ISO 32 ISO 46 ISO 68 Spec.Requirements

SPECIFICATIONS
Specific Gravity @ 15.6°C ASTM D-287 0.87 0.88 0.88 0.89 Report
Viscosity @ 40°C ASTM D-445 20.7 31.1 44.5 64.2 Note 1
Viscosity @ 100°C ASTM D-445 5.16 6.9 9.37 12.2 Note 1
Viscosity @ -15°C, Brookfield ASTM D-2983 350 cP 500 cP 650 cP 1,200 cP Note 1
Viscosity @ -25°C, Brookfield ASTM D-2983 850 cP 1,150 cP 1,400 cP 3,400 cP Note 1
Viscosity @ -30°C MRV TP1 ASTM D-4684 1950 cP 2,600 cP 3,400 cP 7,200 cP 10W= <60,000
Viscosity @ -35°C MRV TP1 ASTM D-4684 3350 cP 4,500 cP 6,200 cP 12,000 cP 5W= <60,000
Viscosity Index ASTM D-2270 196 192 201 191 90 (min)
Dielectric Strength, KV (Avg) ASTM D-877 47 54 47 45 35 (min)
Pour Point ASTM D-97 -50°C -46°C -40°C -36°C Note 1
Flash Point (COC) ASTM D-92 211°C 239°C 240°C 245°C 198°C (min)
Fire Point (COC) ASTM D-92 238°C 261°C 263°C 269°C 218°C (min)
Hydrolytic Stability ASTM D-2619
Copper Wt. Loss (mg) <0.02 <0.02 <0.02 <0.02 0.2
Copper Appearance 1B 1B 1B 1B Report
Water Layer 3 3 3 3 4
Foam Sequence I, II, III (10 ASTM D-892 <30/0 Foam <30/0 Foam <30/0 Foam <30/0 Foam 150/0, 80/0, 150/0
min)
Rust Prevention ASTM D-665
Distilled Water Pass Pass Pass Pass Pass
Syn. Sea Water Pass Pass Pass Pass Pass
Copper Corrosion Strip 3hr @ ASTM D-130 1A 1A 1A 1A DIN 51524 2(Max)
100°C
Rotary Bomb Oxidation, ASTM D-2272 >400 >400 >400 >350 USS 120 (min)
(minutes)
Oxidation Stability (Pressure ASTM D-5483 70.0 (165°C) 70.0 (165°C) 70.0 (165°C) 70.0 (165°C) Note 2
Differential Scanning Modified
Calorimeter) min
Neutralization Number mg ASTM D-974 <0.4 <0.4 <0.4 <0.4 1.5 (Max)
KOH/g
Swell of Synthetic NBR-L DIN 53538, Part
Rubber, % (Avg.) 1
Volume Change (%) 9 7 5 5 0 to 12 (ISO 68) 0 to
10)
Shore A Hardness Change (%) -6 -5 -4 -4 0 to -7
Filterability
A-No Water (s) (Max) Denison TP 90 150 270 340 600 (max)
02100
B-2% Water (s) (Max) HF-0 115 175 300 450 2xA (max)
Requirement
Demulsibility, ML ASTM D-1401 40/40/0 40/40/0 40/40/0 40/40/0 40/37/3
Oil/Water/Emulsion (10 minutes) (10 minutes) (10 minutes) (10 minutes) (30 minutes)
4-Ball Wear, 1h, 167°F, 1200 ASTM D-4172 0.3 – 0.4 0.3 – 0.4 0.3 – 0.4 0.3 – 0.4 USS 127 0.5 (Max)
RPM, 40 kg
FZG Test DIN 51354 11 12 12 12 US.Steel 10 (min)
Biodegradation ASTM D-5864 Ultimate PW1 Ultimate PW1 Ultimate PW1 Ultimate PW1 Ultimate PW1
OECD 301B Readily Readily Readily Readily Readily
Classification
Environmentally Friendly ISO 15380 yes yes yes yes meets/exceeds
USDA Biobased Tested New Carbon yes yes yes yes meets/exceeds >50%
Environmental Management ISO 14001:1996 yes yes yes yes meets/exceeds
System
Ecotoxicity LC-50/EC-50 EPA 560/6-82- meets/exceeds meets/exceeds meets/exceeds meets/exceeds meets/exceeds
002, 003
Product Item # 81090 81050 81060 81070