Index - Section 36

Chemical & Process ANSI Pumps

www.cranepumps.com

ITEM PAGES
Bulletin 3060
Product Numbering System - Series 3060 .................................................................. 1
Typical Architects / Engineers Specifications .............................................................. 2
Standard Materials of Construction - Series 3060 ....................................................... 3
Mechanical Data & Construction Detail ....................................................................... 4
Pressure Temperature Ratings - Series 3060 ............................................................. 5
Corrosion Allowance - Series 3060 ............................................................................. 6
Pump Assembly - Fig. 3060 Series, Oil Lubricated with Shaft Sleeve ....................... 7
Pump Assembly - Fig. 3060 Series, Oil Lubricated ..................................................... 8
Pump Assembly - Fig. 3060 Series, Oil Lub. w/Shaft Sleeve, Single Mech. Seal ....... 9
Pump Assembly - Fig. 3060 Series, Water Jacketed, Oil Lubricated .......................... 10
Pump Assembly - Fig. 3060 Series, Water Jacketed, Oil Lubricated w/Sleeve........... 11
Pump Assembly - Fig. 3060 Series, Grease Lubricated .............................................. 12
Pump Assembly - Fig. 3060 Series, Grease Lubricated w/Shaft Sleeve ..................... 13
Pump Assembly - Fig. 3060 Series, Oil Lub. w/Shaft Sleeve, Jacketed Packing Box
Cooling Frame ............................................................................................................. 14
Pump Assembly - Fig. 3060 Series, Oil Lubricated w/Shaft Sleeve,
Fig. 3066 Cooling Frame ............................................................................................. 15
Optional and Auxiliary Equipment 3060 Series, .......................................................... 16
Seal Assembly Pages .................................................................................................. 17 - 26
Dimensions, Fig. 3062, Pump w/Steel Base, Spacer Coupling & Motor ..................... 27
Dimensions, Fig. 3062, Basic Pump Std & Optional Equipment ................................. 28
Dimensions, Fig. 3065, Pump w/Steel Base, Spacer Coupling & Motor ..................... 29
Dimensions, Fig. 3065, Basic Pump Std & Optional Equipment ................................. 30
Dimensions, Fig. 3066, Pump w/Steel Base, Spacer Coupling & Motor ..................... 31

WARNING:
CANCER AND REPRODUCTIVE HARM -
WWW.P65WARNINGS.CA.GOV

Continued 

A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Index - Section 36
Chemical & Process ANSI Pumps
www.cranepumps.com

Selection Curves, 3500RPM ....................................................................................... 33

Selection Curves, 1750RPM ....................................................................................... 34
Performance Curve, Fig 3062, AA, Size: 1½ x 1 x 6, 3500 & 1750RPM ..................... 35
Performance Curve, Fig 3062, AA-8, Size: 1½ x 1 x 8, 3500 & 1750RPM ................. 36
Performance Curve, Fig 3062, AB-6, Size: 3 x 1½ x 6, 3500 & 1750RPM ................. 37
Performance Curve, Fig 3062, AB-8, Size: 3 x 1½ x 8, 3500 & 1750RPM ................. 38
Performance Curve, Fig 3065, A10, Size: 3 x 2 x 7¼, 3500 & 1750RPM ................... 39
Performance Curve, Fig 3065, A05, Size: 2 x 1 x 9½, 3500 & 1750RPM ................... 40
Performance Curve, Fig 3065, A50, Size: 3 x 1½ x 9½, 3500 & 1750RPM ................ 41
Performance Curve, Fig 3065, A60, Size: 3 x 2 x 9½, 3500 & 1750RPM ................... 42
Performance Curve, Fig 3065, A70, Size: 4 x 3 x 9½, 3500 & 1750RPM ................... 43
Performance Curve, Fig 3065 & 3066, A20, Size: 3 x 1½ x 12B & 3 x 1½ x 12,
3500 & 1750RPM ........................................................................................................ 44
Performance Curve, Fig 3065, A20, Size: 3 x 1½ x 12, 1150RPM .............................. 45
Performance Curve, Fig 3065 & 3066, A30, Size: 3 x 2 x 12B & 3 x 2 x 12,
3500 & 1750RPM ........................................................................................................ 46
Performance Curve, Fig 3065, A30, Size: 3 x 2 x 12, 1150RPM ................................. 47
Performance Curve, Fig 3065, A40, Size: 4 x 3 x 12, 1750 & 1150RPM .................... 48
Performance Curve, Fig 3065, A80, Size: 6 x 4 x 12, 1750 & 1150RPM .................... 49
Performance Curve, Fig 3066, Size: 6 x 4 x 15 DV, 1750 & 1150RPM ....................... 50
Performance Curve, Fig 3066, Size: 6 x 4 x 15 DV, Various RPM ............................. 51

WARNING:
CANCER AND REPRODUCTIVE HARM -
WWW.P65WARNINGS.CA.GOV

End

A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Product Numbering System - 3060 Series
Bulletin 3060
www.cranepumps.com

Chemical & Process ANSI Pumps

The Product Numbering System used, consists of 12 digits, and the following is a description of that system:

0000 - 0000 0 0 0 0
1 thru 4 5 thru 8 9 10 11 12
Digits 1 thru 4 describes the pump figure number.
1 thru 4 Description
3062 Smallest of the Section 36 ANSI Pumps
3065 Medium size Section 36 ANSI Pumps
3066 Large size and high speed Section 36 ANSI Pumps
Digits 5 thru 8 describes the Pump Code (as shown on pump curve & price page).
5 thru 8 Description 5 thru 8 Description
0925 AA 1-1/2 x 1 x 6 3155 A70 4 x 3 x 9-1/2
1825 AB 3 x 1-1/2 x 6 1865 A20 3 x 1-1/2 x 12
0945 AA 1-1/2 x 1 x 8 2265 A30 3 x 2 x 12
1845 AB 3 x 1-1/2 x 8 3165 A40 4 x 3 x 12
2235 A10 3 x 2 x 7-1/4 4265 A80 6 x 4 x 12
1055 A05 2 x 1 x 9-1/2 1866 A20 3 x 1-1/2 x 12B
1855 A50 3 x 1-1/2 x 9-1/2 2266 A30 3 x 2 x 12B
2255 A60 3 x 2 x 9-1/2 4274 A80-15 6 x 4 x 15
Digit 9 describes the cast materials of the pump.
Digit 9 Description Digit 9 Description
1 Cast Iron (Impeller ONLY) 6 316 Stainless Steel
4 Ductile Iron 7 Alloy 20 (also called C-20 for Carpenter 20 SS)
9 Special
Digit 10 describes the shaft and sleeve material.
Digit 10 Description Digit 10 Description
0 5 316 SS shaft with 316 SS sleeve
1 6 316 SS shaft with C-20 sleeve
2 4140 Steel shaft with 316 SS sleeve 7 C-20 shaft with C-20 sleeve
3 4140 Steel shaft with 440 Steel sleeve 8 316 SS shaft
4 4140 Steel shaft with C-20 sleeve 9 Special shaft with special sleeve
Digit 11 describes the shaft sealing method.
Digit 11 Description Digit 11 Description
0 Standard Packed Stuffing box 7 John Crane Single Type 9 Clamped Q/XF1C1
1 John Crane Single Type 1 BF1C1 8 John Crane Single Type 9 Clamped Q/XF171
2 John Crane Single Type 1 BF171 9 Special Seal
3 John Crane Double Type 1 BF1C1
4 John Crane Double Type 1 BF171
5 John Crane Single Type 9 O-ring Q/XF1C1
6 John Crane Single Type 9 O-ring Q/XF171
Digit 12 describes the gland material for either packed stuffing box or mechanical seal construction.
Digit 12 Description Digit 12 Description
4 Ductile Iron 7 Alloy 20 (Also called C-20 for Carpenter 20 SS)
8&9 Special Material

NOTES: 1. Always list on your purchase order either the impeller diameter required or the capacity and head requirements
the impeller is to be designed to handle.
2. These codes are set up for a standard oil lub pump. For any special construction or material configuration not
listed, please list digits 9 thru 12 as 9999 and detail special construction features.

SECTION 36
PAGE 1
DATE 5/15
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Typical Architects/Engineers Specifications
Series 3060 ANSI B73-1M
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

General Shaft Sleeve

Furnish and install as indicated on plans and Pumps shall be equipped with a hooked style shaft
specifications qty _________ Deming Series 3060 sleeve which is securely keyed to the shaft. The surface
Chemical & Process ANSI Centrifugal pump(s) for of the sleeve shall be finished to 32 micro inches.
_______________ type service. Sealing gaskets shall be provided to prevent leakage of
the fluid pumped. The sleeve shall extent throughout the
Operating Conditions stuffing box area and shall be 440C (500 Brinnell) for
Each pump shall be capable of delivering _______ GPM packed pump or stainless steel, of the same metallurgy
of ___________ liquid against ________ feet total head. as the casings for a pump with mechanical seal.
The characteristics of the liquid to be pumped are as Optional is a solid alloy shaft less the sleeve.
follows:
Casing/Seal (Housing) Head Adapter
Liquid Handled ______________________________ The pumps shall be packed box consisting of packing,
Temperature ________________________________ Teflon seal cage and split gland. Stuffing box shall
Specific Gravity ______________________________ include water cooling jacket for use where required. The
Nature of Solids Present _______________________ stuffing box shall include water cooling jacket for use
Percentage of Solids by Weight _________________ where required. The stuffing box shall incorporate an
Viscosity of Liquid at Pumping Temperature ________ external connection through which sealing liquid may be
NPSHA ____________________________________ provided to the seal cage. Pump construction shall permit
conversion from packed stuffing box to mechanical seal
NOTE: Add any additional facts concerning the nature without special machining.
of the liquid which might affect pump construction or
application. As an alternate to packing, the pump can be furnished
with a single seal or double mechanical seal that is
Casing compatible with the material being pumped.
The casing of the pump shall be of (ductile)(316 st. stl.)
material and shall be equipped with (125lb.)(150lb.) Motor
Flat face flanges on the inlet and outlet connections. The motor shall be not less than _____ hp _____ RPM,
The discharge connections shall be top centerline, and NEMA design B squirrel cage type, (drip proof)(TEFC)
parallel to the shaft axis. The casing shall be designed EISA efficiency motor with (1.15)(1.0) service factor and
for working pressures up to 250 lbs., with 1/8" corrosion suitable for operation on (115)(230) volt, 1 phase, (50)
allowance, and have optional (250lb.)(300 lb.) flanges or (60) Hertz power supply OR (200)(230)(460)(575) volt,
raised faces. 3 phase, 60 hertz power supply. Motor size shall be
sufficient to prevent overloading at operating conditions
Rotating Assembly or at the lowest listed head conditions whichever point
The complete pump rotating assembly shall be requires greater horsepower. Following installation,
removable from the casing for inspection and grouting and connection of all piping, pump and motor
maintenance without disturbing the suction and must be checked for alignment in accordance with
discharge connections. Built in jack screw arrangement standards of the Hydraulic Institute.
for ease of maintenance.
The pump and motor shall be mounted on a common
Impeller (fabricated steel)(fabricated steel with drip rim) baseplate.
The impeller shall be of the open single suction type of Pumps are to be coupled to the driver by means of an
(cast iron)(316 st. stl.) both statically and hydraulically approved spacer type coupling with an OSHA approved
balanced for maximum efficiency and smooth operation. coupling guard.
Balance holes shall be provided to keep smooth positive
pressure on the mechanical seal and balanced axial
thrust loads. The impeller shall be threaded to the shaft
so that it will be continually tightening with shaft rotation.

SECTION 36
PAGE 2
DATE 12/10
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Standard Materials of Construction - Series 3060
Bulletin 3060
www.cranepumps.com

Chemical & Process ANSI Pumps

D.I. w/ 316 Case TYPE 316 A-20
MATERIAL GROUP DUCTILE IRON
& P.B. Cover STAINLESS STAINLESS
ITEM
GROUP NO. 4 46 6 7
NAME OF PART
1 Casing Ductile 316 316 A-20
2 Impeller Cast Iron Cast Iron 316 A-20
6 Shaft (Solid) 4140 Steel 316 C-20
6A Shaft (with Sleeve) 4140 Steel
14 Shaft Sleeve 316 316 A-20
11 Packing Box Cover Ductile 316 316 A-20
13 Packing Garlock 8913 JC 1335 Teflon
16 Ball Bearing Steel
17 Split Gland Ductile A-20 A-20
17A Snuffing Gland Ductile A-20 A-20
18 Ball Bearing Steel
19 Frame Cast Iron
22 Bearing Lock Nut Steel
29 Lantern Ring Teflon
33 Bearing Housing Ductile
35 Bearing Cover I.B. Cast Iron
37 Bearing Cover O.B. Ductile
38 Shaft Gasket Teflon
40 Deflector Glass Filled Teflon
47 Bearing Cover Seal Buna
49 Bearing Cover Seal Buna
51 Oil Slinger Bronze
69 Bearing Lock Washer Steel
73 Casing Gasket Durabla
77 Lubricator Steel and Plastic
203 Nameplate 304
204 Adjusting Lock Nut Cadmium Plated Steel
* 206 Split Gland Clip 316
208 Pipe Plug M.I. 316 C-20
210 Hex Nuts 316 C-20
212 Cap Screws Steel 304
213 Cap Screws Cadmium Plated Steel
214 Drive Screw 304
232 O-ring Buna
235 Breather Steel
239 Stud Steel 304
249 Hex Nut Steel 304
273 Casing Foot Cast Iron
274 Frame Foot Cast Iron
275 Lifting Ring Steel
276 Cap Screw Steel
277 Cap Screw Steel
279 Shaft Sleeve Key Stainless Steel
281 Gland Stud 316 C-20
282 Washer 316 C-20
283 Cap Screw 316 C-20
284 Snuffing Gland Ring Garlock 8913
285 Drip Pan 316
286 Jack Screw Cadmium Plated Steel
292 Drain Plug Gasket Glass Filled Teflon
293 Bearing Nameplate 304
332 Cap Screw Cadmium Plated Steel
65 Mechanical Seal As Specified
251 Seal Gland As Specified
401 Gland Gasket Durabla
(*) Omit with Seal Construction

WARNING:
CANCER AND REPRODUCTIVE HARM -
WWW.P65WARNINGS.CA.GOV

SECTION 36
PAGE 3
DATE 10/18
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Mechanical Data & Construction Detail
Series 3060 ANSI B73-1M
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

FIGURE NO. 3062 3065 3066
ANSI NUMBER AA AB AA AB A05 A10 A50 A60 A70 A20 A30 A40 A80 A20 A30 A80
SUCTION 1½ 3 1½ 3 2 3 3 3 4 3 3 4 6 3 3 6
DISCHARGE 1 1½ 1 1½ 1 2 1½ 2 3 1½ 2 3 4 1½ 2 4
MAXIMUM DIAMETER
6 6 8 8 9½ 7¼ 9½ 9½ 9½ 12 12 12 12 12 12 15
IMPELLER
MAXIMUM SOLIDS
3/8 1/2 3/8 1/2 1/4 7/16 5/16 5/8 3/4 3/8 3/8 11/16 1⅛ 3/8 3/8 1
(OPEN IMPELLER)
IMPELLER EYE AREA 3.97 9.62 3.98 5.93 6.49 9.62 9.62 9.62 15.9 9.62 9.62 15.9 38.4 9.62 9.62 28.27
DIAMETER AT COUPLING .875 1.125 1.125

DIAMETER AT COUPLING 1.181 1.968 2.165

BEARING PACKING BOX 1.378 1.771 2.165
SHAFT DATA

DIAMETER BETWEEN
1.562 2.250 2.500
BEARINGS
DIAMETER AT PACKING
1.000 1.375 1.875
BOX UNDER SLEEVE
DIAMETER AT PKG. BOX
1.250 1.750 2.125
SOLID OR SLEEVE O.D.
DIAMETER AT IMPELLER .875 1.250 1.625
PACKING BOX I.D. 1-7/8 2-1/2 3
PACKING BOX LENGTH 2-1/4 2-5/8 3-1/16
LANTERN RING WIDTH 1/2 5/8 3/4
NO. 8 SIZE 5-5/16 SQ. 5-3/8 SQ. 5-7/16 SQ.
PACKING
LENGTH 5-1/4 7 8-1/2
BEARING AT COUPLING END ND 5206WLIA ND 5210WLIA ND 5311WLIA
BEARING AT PACKING BOX END ND 3207 ND 3309 ND 3311
BEARING CENTER LINE TO
5-1/8 6-13/16 6-7/16
BEARING CENTER LINE
BEARING CENTER LINE TO
6-1/16 6-1/8 6-1/16 6-1/8 8-3/8 9-1/2 8-1/4 8-3/8 8-9/16 8-1/4 8-3/8 8-9/16 8-9/16 8-3/8 8-1/2 9-3/4
IMPELLER CENTER LINE
SUCTION WALL THICKNESS 3/8 7/16 3/8 7/16 3/8 7/16 7/16 7/16 1/2 5/8 7/16 7/16 9/16
VOLUTE (CASING) WALL
5/16 3/8 3/8 3/8 3/8 7/16 7/16 7/16 1/2 9/16 7/16 7/16 9/16
THICKNESS
STUDS FOR SPLIT 8
3/8 x 2 3/8 x 2 3/8 x 2-1/4
SNUFFING GLAND (2)
STUDS FOR SEAL GLAND (4) 3/8 x 2 3/8 x 2 3/8 x 2-1/4
NEAREST OBSTRUCTION
2-1/8 2-7/8 1-15/16
PACKING BOX-DEFLECTOR
WEIGHT BARE PUMP 70 74 73 78 150 160 175 185 200 200 220 240 280 220 240 320

ANSI NUMBERS AA AB AA AB A05 A10 A50 A60 A70 A20 A30 A40 A80 A20 A30 A80
FULL DIA. 100% 0.365 0.414 0.649 0.737 1.450 1.106 1.450 1.630 2.088 3.069 3.149 3.800 3.310 2.889 3.804 5.18
WR 2

EFFECT DIA. 85% 0.30 0.33 0.555 0.632 1.01 0.80 1.01 1.11 1.40 2.00 2.05 2.45 2.15 1.91 2.48 4.40
LB. FT.2
DIA. 70% 0.26 0.275 0.454 0.516 0.91 0.49 0.91 0.76 0.092 1.25 1.28 1.50 1.34 1.05 1.55 3.70

FIRST CRITICAL SPEED RPM 11,200 12,830 10,900 10,300 10,146 9,260 10,146 9,432 8,125 8,247 8,125 7,332 7,920 10,510 9,068 6,336

SECTION 36
PAGE 4
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Pressure Temperature Ratings - Series 3060
For 125/150 lb Flanges and 250/300 lb Flanges
www.cranepumps.com
Bulletin 3060

Chemical & Process ANSI Pumps

MATERIAL CODE FOR THESE CHARTS

CODE A CODE A1 CODE B CODE C CODE D CODE M CODE N
304 SS CARBON STEEL BRONZE #5 CAST IRON DUCTILE IRON MONEL NICKEL
316 SS
CARP. A-20
HASTELLOY B
HASTELLOY C
TITANIUM
ZIRCONIUM

SECTION 36
PAGE 5
DATE 6/12
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Corrosion Allowance - Series 3060
Bulletin 3060
www.cranepumps.com

Chemical & Process ANSI Pumps

EXAMPLES: AA-E PUMP - STEEL CASE - 300# FLANGES

100°F - Maximum Working Pressure = 350 psi (PT chart)
Corrosion Allowance = .0623" = 1/16" (CA chart)
500°F - Maximum Working Pressure = 250 psi (PT chart)
Corrosion Allowance = .125" = 1/8" (CA chart)

A20 PUMP - DUCTILE IRON CASE - 150# FLANGES

100°F - Maximum Working Pressure = 220 psi (PT chart)
Corrosion Allowance = .22" = 7/32" (CA chart)
100°F - Actual Working Pressure = 50 psi (Assumed)
Corrosion Allowance = .25" = 1/4" (CA chart)

Minimum case corrosion allowance with good design practice is 1/16" at the maximum allowable working pressure of the pump. Figure 3060 pumps
have this allowance. However, for a given case thickness, corrosion allowance varies inversely with actual working pressure. Thus, a user operating
a pump at lower working pressure can permit more than 1/16" corrosion before retiring the case. The above chart is designed to illustrate this. To
find corrosion allowance enter chart at maximum or actual working pressure and read corrosion allowance at intersection of solid line (diagonal or
vertical).

SECTION 36
PAGE 6
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Pump Assembly - 3060 Series
Oil Lubricated Construction with Shaft Sleeve
www.cranepumps.com Bulletin 3060
Chemical & Process ANSI Pumps

ITEM No. DESCRIPTION ITEM No. DESCRIPTION ITEM No. DESCRIPTION

1 Casing 47 Bearing Cover Seal - Inboard 237 Pipe Plug
2 Impeller 49 Bearing Cover Seal-Outboard 238 Pipe Plug (not shown)
6 Shaft 51 Oil Slinger 239 Stud
11 Packing Box Cover 69 Lockwasher, Bearing 249 Hex Nut
13 Packing 73 Casing Gasket 274 Frame Foot
14 Shaft Sleeve 77 Lubricator 275 Lifting Ring
16 Bearing (inboard) 195 Set Screw 277 Cap screw
17 Gland, Split 203 Name Plate 278 Caution Lable
18 Bearing (outboard) 204 Adjusting Locknut 279 Shaft Sleeve Key
19 Frame 206 Split Gland Clip 281 Gland Stud
22 Nut, Bearing Lock 208 Pipe Plug 286 Jack Screw (Bearing Cover
29 Lantern Ring 210 Hex Nut 292 O-ring (Bearing Cover)
33 Bearing Housing - Outboard 212 Cap screw 293 Bearing Nameplate (Not Shown)
35 Bearing Cover - Inboard 213 Cap Screw 332 Cap Screw
37 Bearing Cover - Outboard 214 Drive screw
38 Shaft gasket 232 O-ring
40 Deflector 235 Breather
46 Coupling Key 236 Pipe Plug

SECTION 36
PAGE 7
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Pump Assembly - 3060 Series
Oil Lubricated Construction
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

ITEM No. DESCRIPTION ITEM No. DESCRIPTION ITEM No. DESCRIPTION

1 Casing 47 Bearing Cover Seal - Inboard 236 Pipe Plug
2 Impeller 49 Bearing Cover Seal-Outboard 237 Pipe Plug
6 Shaft 51 Oil Slinger 238 Pipe Plug (not shown)
11 Packing Box Cover 69 Lockwasher, Bearing 239 Stud
13 Packing 73 Casing Gasket 249 Hex Nut
16 Bearing (inboard) 77 Lubricator 274 Frame Foot
17 Gland, Split 195 Set Screw 275 Lifting Ring
18 Bearing (outboard) 203 Name Plate 277 Cap screw
19 Frame 204 Adjusting Locknut 278 Caution Lable
22 Nut, Bearing Lock 206 Split Gland Clip 281 Gland Stud
29 Lantern Ring 208 Pipe Plug 286 Jack Screw (Bearing Cover
33 Bearing Housing - Outboard 210 Hex Nut 292 O-ring (Bearing Cover)
35 Bearing Cover - Inboard 212 Cap screw 293 Bearing Nameplate (Not Shown)
37 Bearing Cover - Outboard 213 Cap Screw 332 Cap Screw
38 Shaft gasket 214 Drive screw
40 Deflector 232 O-ring
46 Coupling Key 235 Breather

SECTION 36
PAGE 8
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Pump Assembly - 3060 Series
Oil Lubricated Construction with Shaft Sleeve
www.cranepumps.com Single Mechanical Seal - Bulletin 3060
Chemical & Process ANSI Pumps

ITEM No. DESCRIPTION ITEM No. DESCRIPTION ITEM No. DESCRIPTION

1 Casing 65 Mechanical Shaft Seal 274 Frame Foot
2 Impeller 69 Lockwasher, Bearing 275 Lifting Ring
6 Shaft 73 Casing Gasket 277 Cap screw
11 Packing Box Cover 77 Lubricator 278 Caution Lable
14 Shaft Sleeve 195 Set Screw 279 Shaft Sleeve Key
16 Bearing (inboard) 203 Name Plate 281 Gland Stud
18 Bearing (outboard) 204 Adjusting Locknut 286 Jack Screw (Bearing Cover
19 Frame 208 Pipe Plug 292 O-ring (Bearing Cover)
22 Nut, Bearing Lock 210 Hex Nut 293 Bearing Nameplate (Not Shown)
33 Bearing Housing - Outboard 212 Cap screw 332 Cap Screw
35 Bearing Cover - Inboard 213 Cap Screw 401 Gasket
37 Bearing Cover - Outboard 214 Drive screw
38 Shaft gasket 232 O-ring
40 Deflector 235 Breather
46 Coupling Key 236 Pipe Plug
47 Bearing Cover Seal - Inboard 237 Pipe Plug
49 Bearing Cover Seal-Outboard 238 Pipe Plug
51 Oil Slinger 251 Seal Gland

SECTION 36
PAGE 9
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Pump Assembly - 3060 Series
Water Jacketed - Oil Lubricated Construction
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

ITEM No. DESCRIPTION ITEM No. DESCRIPTION ITEM No. DESCRIPTION

1 Casing 47 Bearing Cover Seal - Inboard 236 Pipe Plug
2 Impeller 49 Bearing Cover Seal-Outboard 237 Pipe Plug
6 Shaft 51 Oil Slinger 238 Pipe Plug (not shown)
11 Packing Box Cover 69 Lockwasher, Bearing 239 Stud
13 Packing 73 Casing Gasket 249 Hex Nut
16 Bearing (inboard) 77 Lubricator 274 Frame Foot
17 Gland, Split 195 Set Screw 275 Lifting Ring
18 Bearing (outboard) 203 Name Plate 277 Cap screw
19 Frame 204 Adjusting Locknut 278 Caution Lable
22 Nut, Bearing Lock 206 Split Gland Clip 279 Shaft Sleeve Key
29 Lantern Ring 208 Pipe Plug 280 Gasket
33 Bearing Housing - Outboard 210 Hex Nut 281 Gland Stud
35 Bearing Cover - Inboard 212 Cap screw 286 Jack Screw (Bearing Cover
37 Bearing Cover - Outboard 213 Cap Screw 292 O-ring (Bearing Cover)
38 Shaft gasket 214 Drive screw 293 Bearing Nameplate (Not Shown)
40 Deflector 232 O-ring 332 Cap Screw
46 Coupling Key 235 Breather

SECTION 36
PAGE 10
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Pump Assembly - 3060 Series
Water Jacketed - Oil Lubricated Construction
www.cranepumps.com with Shaft Sleeve - Bulletin 3060
Chemical & Process ANSI Pumps

ITEM No. DESCRIPTION ITEM No. DESCRIPTION ITEM No. DESCRIPTION

1 Casing 47 Bearing Cover Seal - Inboard 237 Pipe Plug
2 Impeller 49 Bearing Cover Seal-Outboard 238 Pipe Plug (not shown)
6 Shaft 51 Oil Slinger 239 Stud
11 Packing Box Cover 69 Lockwasher, Bearing 249 Hex Nut
13 Packing 73 Casing Gasket 274 Frame Foot
14 Shaft Sleeve 77 Lubricator 275 Lifting Ring
16 Bearing (inboard) 195 Set Screw 277 Cap screw
17 Gland, Split 203 Name Plate 278 Caution Lable
18 Bearing (outboard) 204 Adjusting Locknut 279 Shaft Sleeve Key
19 Frame 206 Split Gland Clip 280 Gasket
22 Nut, Bearing Lock 208 Pipe Plug 281 Gland Stud
29 Lantern Ring 210 Hex Nut 286 Jack Screw (Bearing Cover
33 Bearing Housing - Outboard 212 Cap screw 292 O-ring (Bearing Cover)
35 Bearing Cover - Inboard 213 Cap Screw 293 Bearing Nameplate (Not Shown)
37 Bearing Cover - Outboard 214 Drive screw 332 Cap Screw
38 Shaft gasket 232 O-ring
40 Deflector 235 Breather
46 Coupling Key 236 Pipe Plug

SECTION 36
PAGE 11
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Pump Assembly - 3060 Series
Grease Lubricated Construction
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

ITEM No. DESCRIPTION ITEM No. DESCRIPTION ITEM No. DESCRIPTION

1 Casing 47 Bearing Cover Seal - Inboard 239 Stud
2 Impeller 49 Bearing Cover Seal-Outboard 249 Hex Nut
6 Shaft 51 Grease Retainer 274 Frame Foot
11 Packing Box Cover 69 Lockwasher, Bearing 275 Lifting Ring
13 Packing 73 Casing Gasket 277 Cap screw
14 Shaft Sleeve 195 Set Screw 278 Caution Lable
16 Bearing (inboard) 203 Name Plate 281 Gland Stud
17 Gland, Split 204 Adjusting Locknut 286 Jack Screw (Bearing Cover
18 Bearing (outboard) 206 Split Gland Clip 293 Bearing Nameplate (Not Shown)
19 Frame 207 Grease Fitting 332 Cap Screw
22 Nut, Bearing Lock 208 Pipe Plug
29 Lantern Ring 210 Hex Nut
33 Bearing Housing - Outboard 212 Cap screw
35 Bearing Cover - Inboard 213 Cap Screw
37 Bearing Cover - Outboard 214 Drive screw
38 Shaft gasket 222 Pipe Plug
40 Deflector 225 Pipe Plug
46 Coupling Key 236 Pipe Plug

SECTION 36
PAGE 12
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Pump Assembly - 3060 Series
Grease Lubricated Construction with Shaft Sleeve
www.cranepumps.com Bulletin 3060
Chemical & Process ANSI Pumps

ITEM No. DESCRIPTION ITEM No. DESCRIPTION ITEM No. DESCRIPTION

1 Casing 47 Bearing Cover Seal - Inboard 239 Stud
2 Impeller 49 Bearing Cover Seal-Outboard 242 Grease Fitting
6 Shaft 51 Oil Slinger 249 Hex Nut
11 Packing Box Cover 69 Lockwasher, Bearing 274 Frame Foot
13 Packing 73 Casing Gasket 275 Lifting Ring
14 Shaft Sleeve 195 Set Screw 277 Cap screw
16 Bearing (inboard) 203 Name Plate 278 Caution Lable
17 Gland, Split 204 Adjusting Locknut 279 Shaft Sleeve Key
18 Bearing (outboard) 206 Split Gland Clip 281 Gland Stud
19 Frame 207 Grease Fitting 286 Jack Screw (Bearing Cover
22 Nut, Bearing Lock 208 Pipe Plug 293 Bearing Nameplate (Not Shown)
29 Lantern Ring 210 Hex Nut 332 Cap Screw
33 Bearing Housing - Outboard 212 Cap screw
35 Bearing Cover - Inboard 213 Cap Screw
37 Bearing Cover - Outboard 214 Drive screw
38 Shaft gasket 222 Pipe Plug
40 Deflector 225 Pipe Plug
46 Coupling Key 236 Pipe Plug

SECTION 36
PAGE 13
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Pump Assembly - 3060 Series
Oil Lubricated Construction with Shaft Sleeve,
Jacketed Packing Box, Cooling Frame - Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

ITEM No. DESCRIPTION ITEM No. DESCRIPTION ITEM No. DESCRIPTION

1 Casing 47 Bearing Cover Seal - Inboard 238 Pipe Plug (not shown)
2 Impeller 49 Bearing Cover Seal-Outboard 239 Stud
6 Shaft 51 Oil Slinger 249 Hex Nut
11 Packing Box Cover 69 Lockwasher, Bearing 274 Frame Foot
13 Packing 73 Casing Gasket 275 Lifting Ring
14 Shaft Sleeve 77 Lubricator 277 Cap screw
16 Bearing (inboard) 195 Set Screw 278 Caution Lable
17 Gland, Split 203 Name Plate 279 Shaft Sleeve Key
18 Bearing (outboard) 204 Adjusting Locknut 281 Gland Stud
19 Frame 206 Split Gland Clip 286 Jack Screw (Bearing Cover
22 Nut, Bearing Lock 208 Pipe Plug 292 O-ring (Bearing Cover)
29 Lantern Ring 210 Hex Nut 293 Bearing Nameplate (Not Shown)
33 Bearing Housing - Outboard 212 Cap screw 294 Pipe Plug
35 Bearing Cover - Inboard 213 Cap Screw 332 Cap Screw
37 Bearing Cover - Outboard 214 Drive screw
38 Shaft gasket 232 O-ring
40 Deflector 235 Breather
46 Coupling Key 236 Pipe Plug

SECTION 36
PAGE 14
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Pump Assembly - 3060 Series
Oil Lubricated Construction with Shaft Sleeve
www.cranepumps.com Fig. 3066 Cooling Frame - Bulletin 3060
Chemical & Process ANSI Pumps

ITEM No. DESCRIPTION ITEM No. DESCRIPTION ITEM No. DESCRIPTION

1 Casing 47 Bearing Cover Seal - Inboard 238 Pipe Plug (not shown)
2 Impeller 49 Bearing Cover Seal-Outboard 239 Stud
6 Shaft 51 Oil Slinger 249 Hex Nut
11 Packing Box Cover 69 Lockwasher, Bearing 274 Frame Foot
13 Packing 73 Casing Gasket 275 Lifting Ring
14 Shaft Sleeve 77 Lubricator 277 Cap screw
16 Bearing (inboard) 195 Set Screw 278 Caution Lable
17 Gland, Split 203 Name Plate 279 Shaft Sleeve Key
18 Bearing (outboard) 204 Adjusting Locknut 281 Gland Stud
19 Frame 206 Split Gland Clip 286 Jack Screw (Bearing Cover
22 Nut, Bearing Lock 208 Pipe Plug 292 O-ring (Bearing Cover)
29 Lantern Ring 210 Hex Nut 293 Bearing Nameplate (Not Shown)
33 Bearing Housing - Outboard 212 Cap screw 294 Pipe Plug
35 Bearing Cover - Inboard 213 Cap Screw 332 Cap Screw
37 Bearing Cover - Outboard 214 Drive screw
38 Shaft gasket 232 O-ring
40 Deflector 235 Breather
46 Coupling Key 236 Pipe Plug

SECTION 36
PAGE 15
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Optional and Auxiliary Equipment
Series 3060
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

ITEM NO. DESCRIPTION

ITEM NO. DESCRIPTION
11 Packing Box Cover
6 Pump Shaft 13 Packing
11 Packing Box Cover 17 Snuffing Gland
14 Shaft Sleeve 29 Lantern Ring
38 Shaft & Sleeve Key 282 Snuffing Gland Washer
284 Snuffing Gland Ring

ITEM NO. DESCRIPTION

ITEM NO. DESCRIPTION 11 Packing Box Cover
216 Pipe Plug 19 Frame
291 Drain Plug 212 Cap Screw
292 Drain Plug Gasket 288 Drip Pan
289 Pipe Nut
290 Pipe

BEARING NAMEPLATE ITEM NO. 293

SECTION 36
PAGE 16
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Optional Mechanical Seal - 3060 Series
John Crane Single Seals with "O" Ring Seat Mounting
www.cranepumps.com Bulletin 3060
Chemical & Process ANSI Pumps

SECTION 36
PAGE 17
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Optional Mechanical Seal - 3060 Series
John Crane Single Seals with Clamped-In Seat
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

SECTION 36
PAGE 18
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Optional Mechanical Seal - 3060 Series
John Crane Double Seals with "O" Ring Seat Mounting
www.cranepumps.com Bulletin 3060
Chemical & Process ANSI Pumps

SECTION 36
PAGE 19
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Optional Mechanical Seal - 3060 Series
DURA SEALS - Single, Unbalanced, Inside & Outside "RO" &
"ROTT" (w/Clamped Insert Mounting & Various Opt.) -Bulletin 3060
www.cranepumps.com

Chemical & Process ANSI Pumps

SECTION 36
PAGE 20
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Optional Mechanical Seal - 3060 Series
DURA SEAL S - Single, Unbalanced, Inside "RO" & "ROTT"
www.cranepumps.com (with O-ring Insert Mounting) - Bulletin 3060
Chemical & Process ANSI Pumps

SECTION 36
PAGE 21
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Optional Mechanical Seal - 3060 Series
DURA SEALS - Single, Balanced, Inside "PT" & "PTO"
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

SECTION 36
PAGE 22
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Optional Mechanical Seal - 3060 Series
DURA SEAL S - Single, Balanced, Outside "RA" & "RA-TT"
www.cranepumps.com Bulletin 3060
Chemical & Process ANSI Pumps

SECTION 36
PAGE 23
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Optional Mechanical Seal - 3060 Series
DURA SEALS - Single, Balanced, Outside "RA" & "RA-TT"
(with Quench Collar) - Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

SECTION 36
PAGE 24
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Optional Mechanical Seal - 3060 Series
DURA SEAL S - Double, Unbalanced, Inside "CRO"
www.cranepumps.com Bulletin 3060
Chemical & Process ANSI Pumps

SECTION 36
PAGE 25
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Optional Mechanical Seal - 3060 Series
DURA SEALS - Double, Balanced, Inside "RO" & "RO-TT"
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

SECTION 36
PAGE 26
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Fig. 3062
Pumps with Steel Base, Spacer Coupling & Motor
www.cranepumps.com
AA6, AB6, AA8, AB8 - Bulletin 3060

Chemical & Process ANSI Pumps

150# FLANGE DRILLING 300# FLANGE DRILLING * WT

MAX
IN
SIZE SUCT DISCH A B IMP SUCTION DISCHARGE SUCTION DISCHARGE
LBS
DIA
NO. SIZE B.C. NO. SIZE B.C. NO. SIZE B.C. NO. SIZE B.C.
AA6 1½ 1 4¼ 4⅞ 6 4 ⅝ 3⅞ 4 ⅝ 3⅛ 4 ⅞ 4½ 4 ¾ 3½ 70
AB6 3 1½ 4¼ 4⅞ 6 4 ¾ 6 4 ⅝ 3⅞ 8 ⅞ 6⅝ 4 ⅞ 4½ 74
AA8 1½ 1 5 5¼ 8 4 ⅝ 3⅞ 4 ⅝ 3⅛ 4 ⅞ 4½ 4 ¾ 3½ 70
AB8 3 1½ 5 5¼ 8 4 ¾ 6 4 ⅝ 3⅞ 8 ⅞ 6⅝ 4 ⅞ 4½ 74

(*) Weight is based on 150# casing.

Flange thickness per ASA Std B16, 5-1957, Flat Face.

MOTOR
56 143T 145T 182 182T 184 184T 213 213T 215 215T 254U 254T 256U 256T 284U 284T 284TS 286U 286T 286TS
FRAME
BASE NO. 1 2 3
C 9 - 14 13⅛ 13⅛ 14¼ 14⅝ 15¼ 15⅝ 17½ 17¾ 19 19¼ 22⅝ 22⅞ 24⅜ 24⅝ 26⅛ 25⅞ 24½ 27⅝ 27⅜ 26
U ⅝ ⅞ ⅞ ⅞ 1⅛ ⅞ 1⅛ 1⅛ 1⅜ 1⅛ 1⅜ 1⅜ 1⅝ 1⅜ 1⅝ 1⅝ 1⅞ 1⅝ 1⅝ 1⅞ 1⅝
HA 10 12 15
HB 35 39 52
HD 8¼ 8½ 10½ 10½ (was 11⅜)
HE 4 4½ 6
HF 32½ 36½ 49½
HG 2⅞ (was 3) 3 ⁄16 (was 3¼)
3 3½
** WT 134 134 134 154 154 168 168 272 272 297 297 462 462 512 512 569 569 569 629 629 629

(**) WT includes Base, Coupling & Enclosed Motors.

Customer Shop Order No. Date: By:

Pump Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal
Data
Motor MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished Mounted
Data by

SECTION 36
PAGE 27
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Fig. 3062
Basic Pump Standard and Optional Equipment
AA6, AB6, AA8, AB8 - Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

Customer Shop Order No. Date: By:

Pump Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal
Data
Motor MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished Mounted
Data by

SECTION 36
PAGE 28
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Fig. 3065
Pumps with Steel Base, Spacer Coupling & Motor
www.cranepumps.com
A05, A10, A50, A60, A70, A20, A30, A40, A80 - Bulletin 3060

Chemical & Process ANSI Pumps

MAX 150# FLANGE DRILLING 300# FLANGE DRILLING * WT

SIZE SUCT DISCH A B D X IMP SUCTION DISCHARGE SUCTION DISCHARGE IN
DIA NO. SIZE B.C. NO. SIZE B.C. NO. SIZE B.C. NO. SIZE B.C. LBS
A05 2 1 63⁄16 613⁄16 8½ 9½ 4 4¾ ⅝ 3⅛ 5⅞ 4 ¾ 3½ 150
A10 3 2 5 511⁄16 8¼ 7¼ 4 6 ¾ 4¾ 6⅝ 8 ¾ 5 160
A50 3 1½ 63⁄16 613⁄16 8¼ 8½ 9½ 4 ¾ 6 4 ⅝ 3⅞ 8 ⅞ 6⅝ 4 ⅞ 4½ 175
3
A60 3 2 6 ⁄16 613⁄16 9½ 9½ 4 6 ¾ 4¾ 6⅝ 8 ¾ 5 185
A70 4 3 6½ 7½ 11 9½ 8 7½ ¾ 6 7⅞ 8 ⅞ 6⅝ 200
A20 3 1½ 73⁄16 8¼ 10½ 4 6 ⅝ 3⅞ 6⅝ 4 ⅞ 4½ 200
A30 3 2 73⁄16 8¼ 11½ 4 ¾ 6 4 ¾ 4¾ 8 6⅝ 8 ¾ 5 220
10 12 ⅞
A40 4 3 7⅞ 815⁄16 12½ 8 7½ ¾ 6 7⅞ 8 ⅞ 6⅝ 240
A80 6 4 811⁄32 915⁄32 13½ 8 ⅞ 9½ 8 ¾ 7½ 12 10⅝ 8 ⅞ 7⅞ 280
(*) Weight is based on 150# casing. Flange thickness per ASA Std B16, 5-1957, Flat Face.

HD
MOTOR BASE MOTOR
C U HA HB A10-05-50-60-70 A20-30-40-80 HE HF HG HH * WT C U
FRAME NO FRAME
143T 13⅛ 226 182 14¼
⅞ ⅞
145T 13⅛ 226 184 15¼
182T 14¼ 310 213 17½
1⅛ 4 12 45 12 13¾ 4½ 42½ 33⁄16 ¾ 1⅛
184T 15⅝ 310 215 19
213T 17¾ 340
1⅜
215T 19¼ 340
254T 22⅞ 527 254U 22⅝
1⅝ 1⅜
256T 24⅝ 527 256U 24⅜
284T 25⅞ 1⅞ 582 284U 26⅛
5 15 52 12⅜ 14⅛ 6 49½ 3½ ¾ 1⅝
284TS 24½ 1⅝ 582 286U 27⅝
286T 27⅝ 1⅞ 643
286TS 26 1⅝ 643
324T 28¾ 2⅛ 834 324U 29⅛ 1⅞
324TS 27¼ 1⅞ 834 324S 26¾ 1⅝
13
326T 30¼ 2⅛ 899 326U 30⅝ 1⅞
326TS 28¾ 1⅞ 899 326S 28¼ 1⅝
6 18 58 14¾ 7½ 55½ 4 1
364T 33⅛ 2⅜ 1059 364U 33⅝ 2⅛
364TS 31 1⅞ 1059 364US 31 1⅞
14
365TS 32 1⅞ 1124 365U 34⅝ 2⅛
1124 365US 32 1⅞
404TS 34¼ 2⅛ 1454 404US 34¼
15
405TS 36 2⅛ 1454 405US 36
7 18 60 7½ 57½ 4 1 2⅛
1904 444US 38⅝
16
1904 445US 40⅜

Customer Shop Order No. Date: By:

Pump Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal
Data
Motor MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished Mounted
Data by

SECTION 36
PAGE 29
DATE 9/09
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Fig. 3065
Basic Pump Standard and Optional Equipment
A05, A10, A50, A60, A70, A20, A30, A40, A80 - Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

Customer Shop Order No. Date: By:

Pump Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal
Data
Motor MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished Mounted
Data by

SECTION 36
PAGE 30
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Fig. 3066
Pumps with Steel Base, Spacer Coupling & Motor
www.cranepumps.com
A20, A30 - Bulletin 3060

Chemical & Process ANSI Pumps

150# FLANGE DRILLING 300# FLANGE DRILLING * WT

MAX
IN
SIZE SUCT DISCH A B D X IMP SUCTION DISCHARGE SUCTION DISCHARGE
LBS
DIA
NO. SIZE B.C. NO. SIZE B.C. NO. SIZE B.C. NO. SIZE B.C.
A20 3 1½ 7⁄
9 16 8¼ 10½ 4 6 4 ⅝ 3⅞ 8 ⅞ 6⅝ 4 ⅞ 4½ 200
10 12 ¾
A30 3 2 79⁄16 8¼ 11½ 4 6 4 ¾ 4¾ 8 ⅞ 6⅝ 8 ¾ 5 220

(*) Weight is based on 150# casing. Flange thickness per ASA Std B16, 5-1957, Flat Face.

MOTOR BASE HD
C U HA HB HE HF HG HH * WT
FRAME NO A20-30
284T 25⅞ 1⅞ 582
284TS 24½ 1⅝ 582
5 15 52 14⅛ 6 49½ 3½ ¾
286T 27⅝ 1⅞ 643
286TS 26 1⅝ 643
324T 28¾ 2⅛ 834
324TS 27¼ 1⅞ 834
326T 30¼ 2⅛ 899
326TS 28¾ 1⅞ 6 18 58 14¾ 7½ 55½ 4 1 899
364T 33⅛ 2⅜ 1059
364TS 31 1⅞ 1059
365TS 32 1⅞ 1124
404TS 34¼ 2⅛ 1454
15
405TS 36 2⅛ 1454
8 18 60 7½ 57½ 4 1
444TS 38⅞ 2⅜ 1904
16
445TS 40⅞ 2⅜ 1904
Customer Shop Order No. Date: By:
Pump Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal
Data
Motor MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished Mounted
Data by

SECTION 36
PAGE 31
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 www.cranepumps.com

Chemical & Process ANSI Pumps

This page intentionally left blank

SECTION 36
PAGE 32
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Fig. 3060
Selection Curve, 3500 RPM
www.cranepumps.com
Bulletin 3060

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE 33
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Fig. 3060
Selection Curve, 1750 RPM
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
34
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Fig. 3062
Size: 1½ x 1 x 6, AA, 3500 & 1750RPM
www.cranepumps.com
Bulletin 3060

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE 35
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Fig. 3062
Size: 1½ x 1 x 8, AA-8, 3500 & 1750RPM
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
36
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Fig. 3062
Size: 3 x 1½ x 6, AB-6, 3500 & 1750RPM
www.cranepumps.com
Bulletin 3060

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE 37
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Fig. 3062
Size: 3 x 1½ x 8, AB-8, 3500 & 1750RPM
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
38
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Fig. 3065
Size: 3 x 2 x 7-1/4, A10, 3500 & 1750RPM
www.cranepumps.com
Bulletin 3060

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE 39
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Fig. 3065
Size: 2 x 1 x 9-1/2, A05, 3500 & 1750RPM
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
40
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Fig. 3065
Size: 3 x 1½ x 9-1/2, A50, 3500 & 1750RPM
www.cranepumps.com
Bulletin 3060

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE 41
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Fig. 3065
Size: 3 x 2 x 9-1/2, A60, 3500 & 1750RPM
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
42
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Fig. 3065
Size: 4 x 3 x 9-1/2, A70, 3500 & 1750RPM
www.cranepumps.com
Bulletin 3060

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE 43
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Fig. 3065 & 3066
Size: 3 x 1-1/2 x 12B & 3 x 1-1/2 x 12, A20,
3500 & 1750RPM - Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
44
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Fig. 3065
Size: 3 x 1½ x 12, A20, 1150RPM
www.cranepumps.com
Bulletin 3060

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE 45
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Fig. 3065 & 3066
Size: 3 x 2 x 12B & 3 x 2 x 12, A30,
3500 & 1750RPM - Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
46
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Fig. 3065
Size: 3 x 2 x 12, A30, 1150RPM
www.cranepumps.com
Bulletin 3060

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE 47
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Fig. 3065
Size: 4 x 3 x 12, A40, 1750 & 1150RPM
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
48
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Fig. 3065
Size: 6 x 4 x 12, A80, 1750 & 1150RPM
www.cranepumps.com
Bulletin 3060

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE 49
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Fig. 3066
Size: 6 x 4 x15 D.V., 1750 & 1150RPM
Bulletin 3060 www.cranepumps.com

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
50
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 Fig. 3066
Size: 6 x 4 x 15 DV, Various RPM
www.cranepumps.com
Bulletin 3060

Chemical & Process ANSI Pumps

Curves shown performance with liquid having

SECTION 36
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE 51
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
 www.cranepumps.com

Chemical & Process ANSI Pumps

This page intentionally left blank

Curves shown performance with liquid having

SECTION 36
52
Specific Gravity - 1.0, Viscosity - 30 SSU
PAGE
DATE 7/07
A Crane Co. Company USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598