EcoStruxure™ Building www.schneider-electric.

com/buildings | 1

MP-V
SmartX IP Controller

Introduction IP connectivity and flexible network topologies

SmartX IP Controller – MP-V is a multi-purpose, fully The SmartX IP controllers are based on open protocols
programmable, IP based field controller dedicated for that simplify interoperability, IP configuration, and
VAV cooling and heating applications. MP-V integrates device management:
a controller, a damper actuator, and an air flow sensor
in a single compact package for ease of installation. • IP addressing
MP-V can either be used as a standalone BACnet/IP
• BACnet/IP communications
field controller or as part of an EcoStruxure BMS with a
SmartX AS-P or AS-B server or an Enterprise Server as • DHCP for easy network configuration
the parent server. MP-V comes in two models with
different I/O count. The SmartX IP controllers have a dual-port Ethernet
switch, which enables flexible network topologies:
The MP-V has the following features:
• Star
• IP enabled with dual-port Ethernet switch
• Daisy chain
• Integrated damper actuator with feedback signal
• Rapid Spanning Tree Protocol (RSTP) ring
• Factory-calibrated air flow sensor
• Highly available In a star topology, the controller and the parent
EcoStruxure BMS server are individually connected to
• Sensor bus for living space sensors an Ethernet switch. Daisy-chain multiple controllers
together to reduce installation time and cost. Use an
• Mobile commissioning application
RSTP ring topology when you want a non-operational
• Full EcoStruxure Building Operation software controller to be detected and recovered quickly and
support, providing efficient engineering tools efficiently.

Models with a versatile mix of I/O points

MP-V comes in two models with different I/O point
count and a versatile mix of I/O point types that match a
wide variety of VAV applications.

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 2

MP-V
SmartX IP Controller

I/O Point Types by MP-V Models

I/O Point Types MP-V-7A MP-V-9A

Universal inputs 3 4
Triac outputs 3 3
Analog outputs 1 2

Configurations by I/O Point Types

Configurations Universal Inputs Triac Outputs Analog Outputs

Digital inputs yes - -
Counter inputs yes - -
Supervised inputs yes - -
Voltage inputs yes - -
(0 to 10 VDC)
Current inputs yes - -
(0 to 20 mA)
Temperature inputs yes - -
Resistive inputs yes - -
2-wire RTD temperature inputs yes - -
Digital outputs - yes -
Digital pulsed outputs - yes -
PWM outputs - yes -
Tristate outputs - yes -
Tristate pulsed outputs - yes -
Voltage outputs - - yes
(0 to 10 VDC)
Current outputs - - yes
(0 to 20 mA)

Universal inputs For all analog inputs, maximum and minimum levels
The universal inputs are ideal for any mix of can be defined to automatically detect over-range and
temperature, pressure, flow, status points, and similar under-range values.
point types in a building control system.
Triac outputs
As counter inputs, they are commonly used in energy The triac outputs can be used in many applications to
metering applications. As RTD inputs, they are ideal for switch 24 VAC on or off for external loads such as
temperature points in a building control system. As actuators, relays, or indicators. The triac outputs are
supervised inputs, they are used for security isolated from the controller. Triacs are silent and are not
applications where it is critical to know whether or not a adversely affected by relay contact wear.
wire has been cut or shorted. These events provide a
separate indication of alarms and events in the system.

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 3

MP-V
SmartX IP Controller

Analog outputs In WorkStation, you to update the firmware of multiple

The analog outputs are capable of supporting analog SmartX IP controllers at the same time and with
voltage or current point types, without the need for minimum down time. The EcoStruxure BMS server
external bias resistors. Therefore, analog outputs keeps track of the installed firmware to support backup,
support a wide range of devices, such as actuators. restore, and replacement of the controllers and
sensors. The server can host controllers of different
I/O expansion firmware versions.
For applications that require more I/O resources, the
SmartX IP Controller – IP-IO modules provide a Sensor bus for living space sensors
versatile mix of I/O points for any application. For more The SmartX IP controllers provide an interface
information, see the SmartX IP Controller – IP-IO designed for the SmartX Sensor family of living space
Specification Sheet. sensors. The SmartX Sensors offer an efficient way to
sense the temperature, humidity, CO2, and occupancy
Integrated damper actuator with feedback signal in a room. The SmartX Sensors are available with
different combinations of sensor types and various
The integrated damper actuator allows for simplified
covers and user interface options, such as
installation of MP-V directly over the damper shaft. This
touchscreen, setpoint and override buttons, and blank
eliminates the need for separate installation, wiring, and
covers.
positioning of the damper motor. MP-V uses the same
actuator mechanics as many Schneider Electric VAV
controller models from the Andover Continuum, TAC
Vista, TAC I/A Series, and TAC I/NET product lines. The
feedback signal from the actuator makes it possible to
determine the exact position of the damper. The
actuator also features a push button for manual
positioning of the damper during commissioning.

Factory-calibrated air flow sensor

The factory-calibrated air flow sensor uses a state-of-
the-art technology that requires no air flow from the SmartX Sensors
velocity probe. Unlike flow-through sensors, the sensor
The sensor bus provides both power and
does not impose rigid requirements on tubing, dust, or
communications for up to four sensors that are daisy-
filters, and the sensor is not affected by errors induced
chained using standard Cat 5 (or higher) cables. The
on the local probe pressure readings. The sensor
maximum number of sensors that can be connected to
requires no maintenance and a minimum of field
a controller varies depending on the sensor model and
adjustments.
the combination of cover and sensor base type:
Highly available • Blank covers: Up to four sensors of any
The SmartX IP controllers support local trends, combination of sensor base types
schedules, and alarms, enabling local operation when • 3-button and touchscreen covers:
the controller is offline or used in standalone
applications. – Up to two sensor bases with CO2 option
– Up to four sensor bases without CO2 option
With user-defined fallback values, the IP-IO outputs will
be in a predictable state in cases of network disruption. • SmartX LCD temperature sensors: Up to four
sensors are supported
The battery-free power backup of the memory and real-
time clock helps prevent data loss and allows seamless The maximum total length of the sensor bus is 61 m
and quick recovery after a power disruption. (200 ft). For more information, see the SmartX Living
Space Sensors Specification Sheet.

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 4

MP-V
SmartX IP Controller

Mobile commissioning application Field deployment and I/O checkout

The eCommission SmartX Controllers mobile The eCommission SmartX Controllers mobile
application is designed for local configuration, field application does not require an EcoStruxure BMS
deployment, and commissioning of SmartX IP server or a network infrastructure to be in place. You
controllers, and air flow balancing of VAV units. The can use the mobile application to load the controller
mobile application reduces the commissioning time, application directly into the local MP Series controller
allows flexibility in project execution, and minimizes and deploy the controller. The controller application
dependencies on network infrastructure. can be created offline using Project Configuration Tool
or WorkStation. You can also perform an I/O checkout
The mobile application is designed for use with to verify that the controller's I/O points are configured,
Android, Apple (iOS), and Microsoft Windows 10 wired, and operating correctly.
devices. For more information, see the eCommission
SmartX Controllers Specification Sheet. Air flow balancing
Using the eCommission SmartX Controllers mobile
application, you can perform air flow balancing of VAV
units controlled by MP-Vs. An intuitive workflow
automatically guides you through the process. After the
flow balancing, you can generate a report in HTML
format for one or more VAV units. The balancing
parameters associated with each MP-V are stored in
the parent server, which makes it easier to replace the
controller if necessary.

Full EcoStruxure Building Operation software

support
The power of the MP Series controller is fully realized
when it is part of an EcoStruxure BMS, which provides
the following benefits:

• WorkStation/WebStation interface
eCommission SmartX Controllers mobile app • Script and Function Block programming options
Using the eCommission SmartX Controllers mobile • Device discovery
application, you can connect to one or many MP Series
controllers. You can connect to a single MP Series • Engineering efficiency
controller using the eCommission Bluetooth Adapter
connected to a SmartX Sensor. Using a wireless WorkStation/WebStation interface
access point or a network switch, you can connect to a WorkStation and WebStation provide a consistent user
network of MP Series controllers on the local IP experience regardless of which EcoStruxure BMS
network. server the user is logged on to. The user can log on to
the parent EcoStruxure BMS server to engineer,
Device configuration commission, supervise, and monitor the SmartX IP
With the eCommission SmartX Controllers mobile controller and its I/O as well as its attached SmartX
application, you can easily discover SmartX IP Sensors. For more information, see the WorkStation and
controllers on the IP network. You can change the WebStation specification sheets.
configuration of each controller, including the BACnet
and IP network settings, location, and parent server. To Script and Function Block programming options
save engineering time, you can save common device Unique to the industry, the MP Series controllers have
settings and then reuse them for controllers of the same both Script and Function Block programming options.
model. This flexibility assures that the best programming
method can be selected for the application. Existing
programs can easily be reused between the
EcoStruxure BMS server and the controller.

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 5

MP-V
SmartX IP Controller

Device discovery you deploy your server and controller applications to

The enhanced Device Discovery in WorkStation the servers and controllers on site. For more
enables you to easily identify SmartX IP controllers on a information, see the Project Configuration Tool
BACnet network and to associate the controllers with specification sheet.
their parent server.
In addition, you can use Automated Engineering Tool to
Engineering efficiency facilitate your engineering process when using SmartX
IP controllers. This tool provides access to a library of
The engineering and maintenance of SmartX IP
standard controller applications that can be quickly
controllers can be done very efficiently using the
configured and customized using the wizards and
EcoStruxure Building Operation reusability features.
mass edit functions provided in the tool. You can then
With these features, you can create library items
load these customized applications into your target
(Custom Types) for a complete controller application
server. The tool also enables the quick creation of your
that contains programs and all necessary objects such
own templates based on SmartX IP controller
as trends, alarms, and schedules. The controller
applications that you have developed. These templates
application in the Custom Types library is reusable
facilitate a standard approach and easy reuse and
across all controllers of the same model. You can use
duplication of common controller applications. For
the controller application as a base for creating new
more information, see the Automated Engineering Tool
controllers intended for similar applications. You can
specification sheet.
then edit the controller application, and the changes
are automatically replicated to all controllers, while
each controller keeps its local values.

WorkStation supports both online and offline

engineering of SmartX IP controllers. You can make the
configuration changes online or use database mode to
make the changes offline. In database mode, the
changes are saved to the EcoStruxure Building
Operation database so that you can apply the changes
to the controllers later.

Project Configuration Tool enables you to perform all

the engineering off site, without the need for physical
hardware, which minimizes the time you need to spend
on site. You can run the EcoStruxure BMS servers
virtually and engineer the SmartX IP controllers before
Library of standard HVAC applications

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 6

MP-V
SmartX IP Controller

Part Numbers

Product Part number

MP-V-7A SXWMPV7AX10001
MP-V-9A SXWMPV9AX10001
Spare terminal blocks for all MP-V models SXWMPVCON10001
(1 x 2-pin, 2 x 3-pin, 2 x 4-pin, 1 x 5-pin, 1 x 6-pin terminal blocks)
Adapter for damper shaft diameter 9.5 mm (0.375 inch) AM-135
eCommission Bluetooth Adapter SXWBTAECXX10001

Specifications
AC input
Nominal voltage .....................................................................................................................................................24 VAC
Operating voltage range .......................................................................................................................................+/-20 %
Frequency ...........................................................................................................................................................50/60 Hz
Maximum power consumption (MP-V-7A) ................................................................................................................21 VA
Maximum power consumption (MP-V-9A) ................................................................................................................22 VA
Power input protection ...............................................................................................MOV suppression and internal fuse
Environment
Ambient temperature, operating ..................................................................................................0 to 50 °C (32 to 122 °F)
Ambient temperature, storage ............................................................................................-40 to +70 °C (-40 to +158 °F)
Maximum humidity.....................................................................................................................95 % RH non-condensing
Material
Plastic flame rating ..............................................................................................................................................UL94 V-0
Ingress protection rating ............................................................................................................................................IP 20

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 7

MP-V
SmartX IP Controller

Mechanical
Dimensions ......................................................................................161 W x 198 H x 63 D mm (6.3 W x 7.8 H x 2.5 D in.)

Weight ........................................................................................................................................................1.13 kg (2.5 lb)

Installation ......................................................................................................................................Over the damper shaft
Terminal blocks ...............................................................................................................................................Removable
Software compatibility
EcoStruxure Building Operation software ............................................................................................version 2.0 or later
Agency compliances
Emission ..............................................................RCM; EN 61000-6-3; EN 50491-5-2; FCC Part 15, Sub-part B, Class B
Immunity ..............................................................................................................................EN 61000-6-2; EN 50491-5-3
Safety standards .......................................................EN 60730-1; EN 60730-2-11; EN 50491-3; UL 916 C-UL US Listed
Fire performance in air-handling spacesa ........................................................................................................... UL 2043
a) MP-V-7A and MP-V-9A are approved for plenum applications.
Real-time clock
Accuracy, at 25 °C (77 °F) ..............................................................................................................+/-1 minute per month
Backup time, at 25 °C (77 °F) ..................................................................................................................7 days minimum
Communication ports
Ethernet ............................................................................................................................... Dual 10/100BASE-TX (RJ45)
USB ...................................................................................................................................1 USB 2.0 device port (mini-B)
........................................................................................................................1 USB 2.0 host port (type-A), 5 VDC, 2.5 W
Sensor Bus ...........................................................................................................................24 VDC, 2 W, RS-485 (RJ45)
Sensor Bus protection ..........................................Transient voltage suppressors on communication and power signals

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 8

MP-V
SmartX IP Controller

Communications
BACnet .........................................................................................................BACnet/IP, port configurable, default 47808
...................................................................................................BTL B-AAC (BACnet Advanced Application Controller)a
a) See the BTL Product Catalog for up-to-date details on BTL listed firmware revisions on BACnet International's home
page.
CPU
Frequency .......................................................................................................................................................... 500 MHz
Type ..........................................................................................................................................ARM Cortex-A7 dual-core
DDR3 SDRAM .......................................................................................................................................................128 MB
NOR flash memory ..................................................................................................................................................32 MB
Memory backup ......................................................................................................................128 kB, FRAM, non-volatile
Damper actuator
Torque rating .............................................................................................................................................6 Nm (53 lbf.in)
Stroke .........................................................................................................................................0° to 90°, fully adjustable
Timing .............Approximately 2 seconds/degree at 60 Hz and 2.4 seconds/degree at 50 Hz for 90° rotation at 24 VAC
Position indication ....................................................................................................................................Visual indication
Damper position feedback ..........................................................................................................................................Yes
Manual override ..................................................................................................................... Push-button clutch release
Damper shaft diameter ...................................................................................12.7 mm (0.5 inch) or 9.5 mm (0.375 inch)
..........................................................................Adapter kit AM-135 is required for 9.5 mm (0.375 inch) diameter shafts.
Damper shaft minimum length (from VAV box) ................................................................................22.2 mm (0.875 inch)
Air flow sensor
Range ........................................................................................................................................0 to 249 Pa (0 to 1 inH2O)
Resolution ................................................................................................................0.33 Pa (0.001 inH2O) at 25°C (77°F)
Accuracy ...............................................................................................±5% of 249 Pa (1.00 inH2O) span at 25°C (77°F)
Universal inputs, UI
Channels, MP-V-7A ....................................................................................................................................... 3, UI1 to UI3
Channels, MP-V-9A ....................................................................................................................................... 4, UI1 to UI4
Absolute maximum ratings .......................................................................................................................-0.5 to +24 VDC
A/D converter resolution ..........................................................................................................................................16 bits
Universal input protection .............................................................................Transient voltage suppressor on each input
Digital inputs
Range .........................Dry contact switch closure or open collector/open drain, 24 VDC, typical wetting current 2.4 mA
Minimum pulse width ..............................................................................................................................................150 ms
Counter inputs
Range .........................Dry contact switch closure or open collector/open drain, 24 VDC, typical wetting current 2.4 mA
Minimum pulse width ................................................................................................................................................20 ms
Maximum frequency..................................................................................................................................................25 Hz

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 9

MP-V
SmartX IP Controller

Supervised inputs
5 V circuit, 1 or 2 resistors
Monitored switch combinations.............................................................Series only, parallel only, and series and parallel
Resistor range ................................................................................................................................................1 to 10 kohm
For a 2-resistor configuration, each resistor must have the same value +/- 5 %
Voltage inputs
Range ..............................................................................................................................................................0 to 10 VDC
Accuracy...............................................................................................................................+/-(7 mV + 0.2 % of reading)
Resolution................................................................................................................................................................1.0 mV
Impedance..........................................................................................................................................................100 kohm
Current inputs
Range ................................................................................................................................................................0 to 20 mA
Accuracy..........................................................................................................................+/-(0.01 mA + 0.4 % of reading)
Resolution....................................................................................................................................................................1 μA
Impedance .............................................................................................................................................................47 ohm
Resistive inputs
10 ohm to 10 kohm accuracy .......................................................................................................+/-(7 + 4 x 10-3 x R) ohm
R = Resistance in ohm
10 kohm to 60 kohm accuracy .....................................................................................+/-(4 x 10-3 x R + 7 x 10-8 x R2) ohm
R = Resistance in ohm
Temperature inputs (thermistors)
Range................................................................................................................................-50 to +150 °C (-58 to +302 °F)
Supported thermistors
Honeywell .............................................................................................................................................................20 kohm
Type I (Continuum) ...............................................................................................................................................10 kohm
Type II (I/NET) .......................................................................................................................................................10 kohm
Type III (Satchwell) ...............................................................................................................................................10 kohm
Type IV (FD) ......................................................................................................................................................... 10 kohm
Type V (FD w/ 11k shunt) ....................................................................................................................Linearized 10 kohm
Satchwell D?T......................................................................................................................................Linearized 10 kohm
Johnson Controls .................................................................................................................................................2.2 kohm
Xenta....................................................................................................................................................................1.8 kohm
Balco.......................................................................................................................................................................1 kohm
Measurement accuracy
20 kohm...................................................................................................-50 to -30 °C: +/-1.5 °C (-58 to -22 °F: +/-2.7 °F)
...................................................................................................................-30 to 0 °C: +/-0.5 °C (-22 to +32 °F: +/-0.9 °F)
.................................................................................................................. 0 to 100 °C: +/-0.2 °C (32 to 212 °F: +/-0.4 °F)
.............................................................................................................100 to 150 °C: +/-0.5 °C (212 to 302 °F: +/-0.9 °F)
10 kohm, 2.2 kohm, and 1.8 kohm.......................................................-50 to -30 °C: +/-0.75 °C (-58 to -22 °F: +/-1.35 °F)
..........................................................................................................-30 to +100 °C: +/-0.2 °C (-22 to +212 °F: +/-0.4 °F)
.............................................................................................................100 to 150 °C: +/-0.5 °C (212 to 302 °F: +/-0.9 °F)

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 10

MP-V
SmartX IP Controller

Linearized 10 kohm .................................................................................-50 to -30 °C: +/-2.0 °C (-58 to -22 °F: +/-3.6 °F)
...............................................................................................................-30 to 0 °C: +/-0.75 °C (-22 to +32 °F: +/-1.35 °F)
.................................................................................................................. 0 to 100 °C: +/-0.2 °C (32 to 212 °F: +/-0.4 °F)
.............................................................................................................100 to 150 °C: +/-0.5 °C (212 to 302 °F: +/-0.9 °F)
1 kohm ..............................................................................................-50 to +150 °C: +/-1.0 °C (-58 to +302° F: +/-1.8 °F)
RTD temperature inputs
Supported RTDs ..............................................................................................................Pt1000, Ni1000, and LG-Ni1000
Pt1000
Sensor range .....................................................................................................................-50 to +150 °C (-58 to +302 °F)

SmartX IP Controller device environment Sensor range Measurement accuracy

0 to 50 °C (32 to 122 °F) -50 to +70 °C (-58 to +158 °F) +/-0.5 °C (+/-0.9 °F)
0 to 50 °C (32 to 122 °F) 70 to 150 °C (158 to 302 °F) +/-0.7 °C (+/-1.3 °F)

Ni1000
Sensor range .....................................................................................................................-50 to +150 °C (-58 to +302 °F)

SmartX IP Controller device environment Sensor range Measurement accuracy

0 to 50 °C (32 to 122 °F) -50 to +150 °C (-58 to +302 °F) +/-0.5 °C (+/-0.9 °F)

LG-Ni1000
Sensor range .....................................................................................................................-50 to +150 °C (-58 to +302 °F)

SmartX IP Controller device environment Sensor range Measurement accuracy

0 to 50 °C (32 to 122 °F) -50 to +150 °C (-58 to +302 °F) +/-0.5 °C (+/-0.9 °F)

RTD temperature wiring

Maximum wire resistance.........................................................................................................20 ohm/wire (40 ohm total)
Maximum wire capacitance.......................................................................................................................................60 nF
The wire resistance and capacitance typically corresponds to a 200 m wire.
Triac outputs, DO
Channels, MP-V-7A ................................................................................................................................... 3, DO1 to DO3
Channels, MP-V-9A ................................................................................................................................... 3, DO1 to DO3
Output rating (for each triac output) ..................................................................................................................Max. 0.5 A
Voltage......................................................................................................................................................24 VAC +/-20 %
Commons.................................................................................................................................COM (terminal number 18)
The common terminal COM can be connected to 24 VAC or to ground.
Common voltage, high side output.........................................................................................................................24 VAC
Common voltage, low side output .............................................................................................................0 VAC (ground)
Minimum pulse width ..............................................................................................................................................100 ms
Triac output protection ..................................................................................MOV and snubber across each triac output
..........................................................................................................................................MOV from triac COM to ground

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 11

MP-V
SmartX IP Controller

Analog outputs, AO
Channels, MP-V-7A ....................................................................................................................................... 1, VO1/CO1
Channels, MP-V-9A .................................................................................................................2, VO1/CO1 and VO2/CO2
Analog output protection ............................................................................Transient voltage suppressor on each output
Voltage outputs
Range ..............................................................................................................................................................0 to 10 VDC
Accuracy..............................................................................................................................................................+/-60 mV
Resolution.................................................................................................................................................................10 mV
Minimum load resistance........................................................................................................................5 kohm to ground
Load range........................................................................................................................................................0 to +2 mA
Terminals .....................................................................................................................Voltage Output (VO), Return (RET)
Current outputs
Range ................................................................................................................................................................0 to 20 mA
Accuracy ............................................................................................................................................................+/-0.2 mA
Resolution..................................................................................................................................................................21 µA
Load range.....................................................................................................................................................0 to 650 ohm
Terminals .....................................................................................................................Current Output (CO), Return (RET)

Terminals • Individual 24 VDC power sources to the field must

be current limited to maximum 4 A for UL
Follow proper installation wiring diagrams and compliant installations, and maximum 6 A in other
instructions, including these instructions: areas.
• MP-V-7A and MP-V-9A have several RET terminals • For more information on wiring, see Hardware
for connection of I/O returns, so a common Reference Guide.
chassis/signal ground rail is optional and may not
be needed.

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 12

MP-V
SmartX IP Controller

MP-V-7A

MP-V-9A

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 13

MP-V
SmartX IP Controller

Part Numbers in AMER Region for Network Connectivity Accessories

Product descriptiona Part number (AMER region)

Cat 6 field-term plug, UTP ACTPG6TLU001
Cat 6 pass-through plug, UTP, 100-pack ACTPG6PTU100
Actassi crimping tool ACTTLCPT
Cat 6 cable, UTP, 1000 ft (305 m), CMP, green ACT4P6UCP1ARXGR
Cat 6 patch cord, UTP, 30 ft (9 m), CMP, green ACTPC6UBCP30AGR
Cat 6 patch cord, UTP, 50 ft (15 m), CMP, green ACTPC6UBCP50AGR
Cat 6 patch cord, UTP, 70 ft (21 m), CMP, green ACTPC6UBCP70AGR
Cat 6 patch cord, UTP, 90 ft (27 m), CMP, green ACTPC6UBCP90AGR
Cat 5e pass-through plug, UTP, 100-pack ACTPG5EPTU100
Cat 5e cable, UTP, 1000 ft (305 m), CMP, green ACT4P5EUCP1ARXGR
Cat 5e patch cord, UTP, 30 ft (9 m), CMP, green ACTPC5EUBCP30AGR
Cat 5e patch cord, UTP, 50 ft (15 m), CMP, green ACTPC5EUBCP50AGR
Cat 5e patch cord, UTP, 70 ft (21 m), CMP, green ACTPC5EUBCP70AGR
Cat 5e patch cord, UTP, 90 ft (27 m), CMP, green ACTPC5EUBCP90AGR

a) For more information, see the Product Selection Guide (SmartX IP Controllers - Accessories). Abbreviations: UTP (Unshielded Twisted Pair), CMP (Plenum-rated
cable)

Part Numbers in EMEA Region for Network Connectivity Accessories

Product descriptiona Part number (EMEA region)

Cat 6 field-term plug, UTP ACTPG6TLU001
Cat 6 pass-through plug, UTP, 100-pack ACTPG6PTU100
Actassi crimping tool ACTTLCPT
Cat 6 cable, UTP, 305 m (1000 ft), Euroclass D, green VDICD116118
Cat 6 patch cord, UTP, 10 m (32 ft), LSZH, green ACTPC6UBLS100GR
Cat 6 patch cord, UTP, 15 m (49 ft), LSZH, green ACTPC6UBLS150GR
Cat 6 patch cord, UTP, 20 m (65 ft), LSZH, green ACTPC6UBLS200GR
Cat 6 patch cord, UTP, 25 m (82 ft), LSZH, green ACTPC6UBLS250GR
Cat 5e pass-through plug, UTP, 100-pack ACTPG5EPTU100
Cat 5e cable, UTP, 1000 ft (305 m), Euroclass D, green VDICD115118
Cat 5e patch cord, UTP, 10 m (32 ft), LSZH, green ACTPC5EUBLS100GR
Cat 5e patch cord, UTP, 15 m (49 ft), LSZH, green ACTPC5EUBLS150GR
Cat 5e patch cord, UTP, 20 m (65 ft), LSZH, green ACTPC5EUBLS200GR
Cat 5e patch cord, UTP, 25 m (82 ft), LSZH, green ACTPC5EUBLS250GR

a) For more information, see the Product Selection Guide (SmartX IP Controllers - Accessories). Abbreviations: UTP (Unshielded Twisted Pair), CMP (Plenum-rated
cable), LSZH (Low Smoke Zero Halogen)

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
EcoStruxure™ Building www.schneider-electric.com/buildings | 14

MP-V
SmartX IP Controller

Part Numbers in Pacific Region for Network Connectivity Accessories

Product descriptiona Part number (Pacific region)

Cat 6 field-term plug, UTP ACTPG6TLU001
Cat 6 pass-through plug, UTP, 100-pack ACTPG6PTU100
Actassi crimping tool ACTTLCPT
Cat 6 cable, UTP, 305 m (1000 ft), PVC, green 2D4P6IPV3B-GR
Cat 6 patch lead, UTP, 10 m (32 ft), PVC, green RJ6_100PL-GR
Cat 6 patch lead, UTP, 15 m (49 ft), PVC, green RJ6_150PL-GR
Cat 6 patch lead, UTP, 20 m (65 ft), PVC, green RJ6_200PL-GR
Cat 6 patch lead, UTP, 25 m (82 ft), PVC, green RJ6_250PL-GR
Cat 5e pass-through plug, UTP, 100-pack ACTPG5EPTU100
Cat 5e cable, UTP, 305 m (1000 ft), PVC, green 2D4P5IPV3B-GR
Cat 5e patch lead, UTP, 10 m (32 ft), PVC, green RJ5_100PL-GR
Cat 5e patch lead, UTP, 15 m (49 ft), PVC, green RJ5_150PL-GR
Cat 5e patch lead, UTP, 20 m (65 ft), PVC, green RJ5_200PL-GR
Cat 5e patch lead, UTP, 25 m (82 ft), PVC, green RJ5_250PL-GR

a) For more information, see the Product Selection Guide (SmartX IP Controllers - Accessories). Abbreviations: UTP (Unshielded Twisted Pair), PVC (Polyvinyl
chloride)

Regulatory Notices
Federal Communications Commission CE - Compliance to European Union (EU)
FCC Rules and Regulations CFR 47, Part 15, Class B 2014/30/EU Electromagnetic Compatibility Directive
This device complies with part 15 of the FCC Rules. Operation is subject to the following two 2011/65/EU Restriction of Hazardous Substances (RoHS) Directive
conditions: (1) This device may not cause harmful interference. (2) This device must accept 2015/863/EU amending Annex II to Directive 2011/65/EU
any interference received, including interference that may cause undesired operation. This equipment complies with the rules, of the Official Journal of the European Union, for
governing the Self Declaration of the CE Marking for the European Union as specified in the
Industry Canada above directive(s) per the provisions of the following standards: EN 60730-1, EN 60730-2-
This Class B digital apparatus complies with Canadian ICES-003. 11, and EN 50491-3 Safety Standards.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Regulatory Compliance Mark (RCM) - Australian Communications and Media WEEE - Directive of the European Union (EU)
Authority (ACMA) This equipment and its packaging carry the waste of electrical and electronic equipment
This equipment complies with the requirements of the relevant ACMA standards made under (WEEE) label, in compliance with European Union (EU) Directive 2012/19/EU, governing the
the Radiocommunications Act 1992 and the Telecommunications Act 1997. These disposal and recycling of electrical and electronic equipment in the European community.
standards are referenced in notices made under section 182 of the Radiocommunications
Act and 407 of the Telecommunications Act.
UL 916 Listed products for the United States and Canada, Enclosed Energy
Management Equipment. UL file E80146.

www.schneider-electric.com

03-30036-01-en, April 2019

© 2019 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.