Assignment- I

Design of Concrete Structure (5CE4-03) Part B

Attempt any two questions
Q.No
Part A Questions Marks
.
Q.No
Questions Marks
.
Determine the depth of neutral axis of given
1. What is Singly reinforced beam? 2 section. Use M20 mix and Fe250 grade steel.
2. Write the types of beam? 2

3. Write the full form of WSM? 2

17. 5
4. What is permissible stress for concrete? 2

5. Draw the strain diagram for Limit State? 2

6. Write the compressive force in beam? 2

7. What is neutral axis? 2

8. What is lever arm? 2 Determine the depth of neutral axis of a

beam 250mm×400mm reinforced with 3
9. Write the full form of LSM? 2 18. bars of 20 mm diameter. Also check for the 5
10. What is Doubly reinforced beam? 2 type of section. Use M20 concrete and Fe415
steel.
11. What is permissible stress for steel in case 2
Determine the moment of resistance of a
of WSM?
beam of dimension 250mm×350mm. The
12. Write the Tensile force in beam in case of 2 area of steel consists of 3 bars of 12mm
LSM? 19. 5
diameter placed at a distance of 40mm from
13. What is under reinforced section? 2 bottom of beam. Use M20 mix and Fe415
steel.
14. How much the depth of neutral axis for 2
balanced section? (WSM) A reinforced concrete slab 150mm thick is
reinforced with 10mm bars @ 180mm c/c.
15. Write the maximum depth of neutral axis 2 The reinforcement is located at an effective
for different type of steel grade? 20. 5
depth of 125mm from top. Calculate the
16. What is ultimate load? 2 moment of resistance of the section. Use
M20 concrete mix and Fe415 steel.
21. A reinforced concrete beam is 300mm×700 5
mm is subjected to a bending moment of
150KNm. Determine the area of
 reinforcement if M20 concrete and Fe415
steel is used. Take effective cover as 40mm.
Part C
Find the depth of neutral axis, and
percentage of steel for a balanced section of Attempt any one question
22. a singly reinforced beam using: (i) M20 and 5
plain mild steel bars. (Fe 250), (ii) M20 and Q.No
Questions Marks
Fe 415 bars. .
23. Find the moment of resistance of a R.C.C. 5 An R.C.C. beam is required to carry a
beam 300 mm wide and 500 mm effective uniformly distributed load of 25KN/m
depth is reinforced with 3 bars of 16 mm. inclusive of its self-weight. The effective
29. 9
M20 concrete and Fe 415 steel is used. span of the beam is 8m. Design the beam for
24. Find the moment of resistance of a beam 5 flexure only. Use M30 concrete and Fe415
25cm×50cm if it is reinforced with 2-12mm steel.
bars in compression zone and 4-20mm bars Determine the moment of resistance of a
in tension zone, each at an effective cover of R.C.C. beam 350 x 550 mm (effective) and is
40mm. Assume M15 mix and Fe250 grade reinforced with 3 bars of 20 mm diameter.
steel. 30.
The permissible stresses in concrete and 9
25. Determine the moment of resistance of the 5 steel are 7 N/mm and 230 N/mm2. Take m =
beam having dimension as 300mm×500 mm 13.33
(effective). The beam is reinforced with A rectangular beam of 300 mm width and
1963 mm2 of steel in the tension zone. Use 500 mm effective depth is reinforced with 4
M20 concrete mix and Fe415 steel. Also x 16 mm dia. tension bars. Determine the
comment on the design of beam. 31. stress induced in the top compression fibre 9
26. Analyse a rectangular beam 300mm width 5 of the concrete and tension steel when it is
and 500mm effective depth to determine the subjected to a moment of 50 kNm. Consider
ultimate moment of resistance for the M20 concrete.
tension reinforcement of 4-16mm diameter An R.C.C. beam 300 mm x 640 mm overall
bars consider M20 mix and Fe415 steel. is reinforced with 4 bars of 20 mm
27. An R.C.C. beam 400 x 600 mm effective is 5 diameter. The beam has to carry a
reinforced with 4 bars of 25 mm diameter. superimposed load of 50 kN/m, including
The beam is subjected to a bending moment the self weight of the beam, over an effective
150 kNm. Find the stresses set up in steel span of 4 m. Find the actual stresses 9
32.
and concrete, if m = 13.33 developed in steel and concrete. The
28. Design a rectangular beam for an effective 5 effective cover is 40 mm. Take m = 13.33
span of 6m. The superimposed load is 80 Also, find the compressive stress in concrete
KN/m and size of beam is limited to at 50 mm from top of the beam and draw
30cm×70cm overall. Use M20 mix and bending stress diagram.
Fe415 grade steel.
33. An R.C.C. beam is required to resist a 9
bending moment of 70KNm. Design the
beam for flexure, taking b/d=0.5. Use M20
concrete and TMT (Fe415 bars).
34. Determine the moment of resistance of a 9
singly reinforced 160 mm wide and 300 mm
deep (effective) beam. The reinforcement
consists of 4 bars of 16 mm diameter. The
material used is M15 concrete and Fe 250
steel. Take m = 18 If the span of the the
beam is 5 m, find the maximum distributed
load which the beam can carry, inclusive of
its own weight.
35. A rectangular beam of width 350 mm is 9
subjected to a uniformly distributed load of
15 kN/m over an effective span of 8 m.
Determine the depth required for the beam
and also calculate the area of tensile
reinforcement required. Use M20 concrete
and Fe 250 steel.
36. A rectangular beam is 20cm wide and 40cm
deep upto the centre of reinforcement. Find 9
the area of reinforcement required if it has
to resist a moment of 25KNm. Use M20
concrete mix and Fe415 steel.