24" LCD Monitor Dell P2419H

Service
Service
Service

Simplified

1
Important Safety Notice
Proper service and repair is important to the safe, reliable operation of all DELL Company Equipment. The service
procedures recommended by DELL and described in this service manual are effective methods of performing
service operations. Some of these service operations require the use of tools specially designed for the purpose.
The special tools should be used when and as recommended.

It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read
in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. DELL could not possibly know, evaluate and advise the service trade of all conceivable ways
in which service might be done or of the possible hazardous consequences of each way. Consequently, DELL has
not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is
not recommended by DELL must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, DELL Company will be referred to as DELL.

WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create
shock, fire, or other hazards.

Under no circumstances should the original design be modified or altered without written permission from DELL.
DELL assumes no liability, express or implied, arising out of any unauthorized modification of design.

Servicer assumes all liability.

FOR PRODUCTS CONTAINING LASER:

DANGER-Invisible laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.

TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION
OF THIS SERVICE MANUAL.

Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth
may damage the panel.)

2
1. Exploded view diagram with list of items
No. Description Q’ty
1 LOGO DELL 1
2 DECO_BEZEL 1
3 DECO_PLATE 1
4 PANEL 1
5 MIDDLE_FRAME 1
8 INSULATING SHEET 1
12 ADAPTER BOARD 1
13 CONVERSION BOARD 1
14 KEY 1
15 MAINFRAME 1
18 SHIELD_USB 1 No. Part No. Description Q’ty
19 USB BOARD 1 6 0Q1G6019 1 SCREW(DECO BEZEL /MIDDLE FRAME) 3
21 Latch 1 7 QM1G30300301200ARA SCREW M3 3(MIDDLE FRAME/PANEL) 11
22 STAND_BUTTON 1 9 0D1G1030 6120 SCREW D3 6 (POWER BOARD/MAINFRAME) 2
23 spring 2 10 QM1G38400601200ARA SCREW -- 6mm(POWER BOARD/MAINFRAME) 1
24 BKT_LOCKER 1 11 0D1G1030 6120 SCREW D3 6(MAIN BOARD/MAINFRAME) 3
25 REAR_COVER 1 16 QM1G30300301200ARA SCREW M3 3(MAINFRAME/PANEL) 4
27 stand ass'y 1 17 0Q1G2030 5120 SCREW 5 (USB BOARD/REAR COVER) 1
28 BASE_ASS’Y 1 20 0Q1G2030 5120 SCREW 5 (Latch/REAR COVER) 2
29 KEY BOARD 1 26 0M1G2940 10225 CR3 SCREW M4 10(REAR COVER/PANEL) 4
2. Wiring connectivity diagram

5
3.Mechanical Instruction

Tools Required
List the type and size of the tools that would typically can be used to disassemble the product to a point
where components and materials requiring selective treatment can be removed.
Tool Description:
− Phillip head Screwdriver
− Hex Screwdriver
Penknife

6
3.1Disassembly Procedures:

Step Figure Remark

Turn off power,

S1.Before
Unplug external
disassemble
cablesfrom product

Press the button on the

red then pull out the
S2. Remove the
stand upward, stand
stand
will be remove.

7
 Use a Philips-head
screwdriver to remove
4 screws for unlocking
1 2
mechanisms.
(No.1~4 screw
size=M4x10;
3 4
Torque=12±2kgf.cm）
S3.Remove the
REAR COVER.
Use Penknife to
separate the bezel and
rear cove follow the
arrows in sequence,
then you can take out
rear cover.

S4.Remove the Disconnect the pins

Cables and and the tapes.
Tapes

8
 Use a Philips-head
4 8 screwdriver to remove
5 6 7
3 11 screws for
9
unlocking middle
S5.Remove the
frame.
Middle_Frame 2 10
(No.1~11 screw
1 11 size=M3x3;

Torque=3±0.5kgf.cm）

1. Use a Philips-head
2 screwdriver to remove
1
4 screws for unlocking
S6.Remove the main frame.
Main frame and (No.1~4 screw
3 4
the pin size=M3x3;
Torque=3±0.5kgf.cm)

2. Disconnect the pin

9
 Use a Philips-head
screwdriver to remove
3 screws for unlocking
the Deco bezel
(No.1~3 screw

1 2 3 size=M2x2.5;
Torque=0.9±0.4kgf.cm
)

S7.The Middle
frame、The Deco
Bezel and the
Key Board

Use a Philips-head
screwdriver to remove
3 screws for unlocking
Main board.
1
(No.1~3 screw
2
size=D3x6
Torque=6±1kgf.cm)
3
S8.Remove the
Main Board

Use a hex screwdriver

to remove 2 screws for
1 2 unlocking mainboard

（No.1~2 Hex screw

Torque= 4.5±
0.5kgf.cm)
10
S9.Disconnect
Disconnect the pins
the pins

1. Take off the Mylar

2. Use a Philips-head
screwdriver to remove
3 screws for unlocking
S10.Remove the the Power Board
1
Mylar and the (No.1~2 screw
Power Board size=D3x6
2
3 Torque=6±1kgf.cm

No.3 screw size=M4x6

Torque=6±1kgf.cm)

S11.The
Mainframe

11
 Use a Philips-head
screwdriver to remove

1 1 screw for unlocking

S12.Remove the
the USB board
USB board
(No.1 screw
size=Q3x5
Torque=4±1kgf.cm)

S13.The Rear
Cover

12
3.2 Assembly Procedures:
Step Figure Remark

1. Assembly the Mylar

2. Use a Philips-head
screwdriver to screw 3
screws for locking the
S1.Assembly the 1 Power Board
Mylar and the (No.1~2 screw
Power Board 2 size=D3x6
3
2
3 Torque=6±1kgf.cm

No.3 screw size=M4x6

Torque=6±1kgf.cm)

Connect the pins

Use a Philips-head
S2. Assembly the
screwdriver to screw 3
Main Board
screws for locking
Main board.
(No.1~3 screw
size=D3x6
Torque=6±1kgf.cm)

Use a hex screwdriver

to screw 2 screws for
locking mainboard

（No.1~2 Hex screw

Torque=
4.5±0.5kgf.cm)

13
S3.Assembly
the Middle Assembly Key board
frame、Deco and Deco bezel
Bezel and the
Key Board

Use a Philips-head
screwdriver to screw 3
screws for locking the
Deco bezel
(No.1~3 screw
size=M2x2.5;
Torque=0.9±0.4kgf.cm
2 3
1 )

Use a Philips-head
1 screwdriver to screw 1
screw for locking the
S4.Assembly the
USB board
USB board
(No.1 screw
size=Q3x5
Torque=4±1kgf.cm)

14
 1. Disconnect the pin

2 2. Use a Philips-head
1
screwdriver to screw 4
S5.Assembly the
screws for locking
Main frame
main frame.
3 4
(No.1~4 screw
size=M3x3;
Torque=3±0.5kgf.cm)

Use a Philips-head
screwdriver to screw
11 screws for locking
S6. Assembly the
middle frame.
Middle_Frame
(No.1~11 screw
size=M3x3;

Torque=3±0.5kgf.cm）

S7.Connect the
Cables and paste
the tapes

15
 Use a Philips-head
1 2
screwdriver to screw 4
S8.Assembly screws for locking
the REAR mechanisms.
3 4
COVER. (No.1~4 screw
size=M4x10;

Torque=12±2kgf.cm）

16
S9. Assembly the
stand

17
4. Trouble shooting instructions

18
19
20
21
22
23
24
25