Scribd
Upload
23 views

EEE211L - Lab 5 - Binary Arithmetic

The document describes a lab experiment on binary arithmetic using integrated circuits. Students will: 1) Understand binary addition and subtraction using half and full adders. 2) Perform addition and subtraction of 4-bit binary numbers using a 7483 IC. 3) Understand BCD addition and implement a 4-bit BCD adder using two 7483 ICs, AND gates, and OR gates to convert the binary sum to BCD.

Uploaded by

Md Kaium
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
23 views

EEE211L - Lab 5 - Binary Arithmetic

The document describes a lab experiment on binary arithmetic using integrated circuits. Students will: 1) Understand binary addition and subtraction using half and full adders. 2) Perform addition and subtraction of 4-bit binary numbers using a 7483 IC. 3) Understand BCD addition and implement a 4-bit BCD adder using two 7483 ICs, AND gates, and OR gates to convert the binary sum to BCD.

Uploaded by

Md Kaium
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Department of Electrical & Computer Engineering, NSU Digital Logic Design Lab

Lab 5: Binary Arithmetic

A. Objectives

• Understand the concept of binary addition and subtraction.


• Learn about half and full binary adders.
• Perform binary addition and subtraction using IC7483.
• Understand the concept of BCD addition and implement a BCD adder using IC7483

B. Theory

Digital computers perform a variety of information-processing tasks.


Among the functions encountered are the various arithmetic operations.
The most basic arithmetic operation is the addition of two binary digits.
This simple addition consists of four possible elementary operations: 0 +
0 = 0, 0 + 1 = 1, 1 + 0 = 1, and 1 + 1 = 10. The first three operations
produce a sum of one digit, but when both augend and addend bits are
equal to 1, the binary sum consists of two digits. The higher significant
bit of this result is called a carry. When the augend and addend numbers
contain more significant digits, the carry obtained from the addition of
two bits is added to the next higher order pair of significant bits.

A combinational circuit that performs the addition of two bits is called a


half adder. One that performs the addition of three bits (two significant
bits and a previous carry) is a full adder. The names of the circuits stem Figure B.1: Logic Diagram
from the fact that two half adders can be employed to implement a full and Truth Table of a half adder
adder.

In practice, binary addition is usually performed using ICs that contain


several full adders chained together and can be used to add together
groups of bits. These ICs themselves can be chained to form even larger
adders. Since binary subtraction is performed by complement addition,
the adder ICs can also be used for subtraction by using some extra logical
operations to perform the complement calculation.

Figure B.2:
Logic Diagram
and Truth Table
of a full adder

EEE211L/ETE211L Lab-5 Page 1 of 6


Department of Electrical & Computer Engineering, NSU Digital Logic Design Lab

Experiment 1: Binary Adder Subtractor


C.1 Apparatus

• Trainer Board
• 1 x IC 7483 4-bit binary adder
• 2 x IC 7486 quadruple 2-input XOR gates

New Apparatus:
IC 7483: The 16-pin 7483 IC is a 4-bit full adder. That means, it can take
two 4-bit binary numbers (A4A3A2A1 and B4B3B2B1) and calculate the sum
(S4S3S2S1). The input carry (if any) is connected to C0 and the output carry
is obtained from C4. Unlike most other ICs used so far, in the 7483, the 5V
VCC needs to be connected to pin 5 and the ground to pin 12.

Two 7483 ICs can be cascaded to form an 8-bit ripple-through-carry adder.


The lower 4 bits of each number is used as input for the first 7483 and the
output carry is connected to the input carry of the next 7483. The higher 4
bits of each number is used as input for the second 7483. The first IC
provides the lower 4 bits of the sum and the second one provides the upper
4 bits. Figure C.1.1:
Pinout of IC7483

D.1 Procedure

Figure D.1.1: 4-bit Adder-Subtractor

EEE211L/ETE211L Lab-5 Page 2 of 6


Department of Electrical & Computer Engineering, NSU Digital Logic Design Lab

1. Construct the 4-bit adder-subtractor circuit of Figure D.1.1 using 4-bit full adder and the XOR gates. Use
four binary switches to represent the bits of input A and four more binary switches to represent the bits of
input B. Use another switch for the mode select M. Use 4 LEDs to view the output S and another LED for
the output carry C4. (Be)
2. Complete the operations in Table F.1.1.
i. For each operation, convert the first operand to binary as A, and the second operand as B.
ii. Write down the value of M required for the operation. M should be 0 for an addition operation and
1 for a subtraction operation.
iii. Note down the values of the output carry C4 and data output S4-S1. Verify the results.

Experiment 2: BCD Adder


C.2 Apparatus

• Trainer board
• 2 x IC 7483 4-bit binary adder
• 1 x IC 7408 quadruple 2-Input AND gates
• 1 x IC 7432 quadruple 2-Input OR gates

D.2 Procedure

1. Complete Table F.2.1 for the BCD sum. In BCD, a group of four bits can only represent the decimal values
from 0 to 9, after which we need to use higher order bits. Here, ‘C’ represents that higher order bit.
2. Construct the circuit of Figure D.2.1. Unlike the previous circuit, this is a 4-bit adder despite the fact that
two 7483 ICs are being used.
i. The output of the first IC7483 (the upper one in the figure) is fed into the input of the second IC7483.
ii. The output of the second IC7483 (the lower one in the figure) is connected to four LEDs.
iii. The combinational circuit created with AND and OR gates does the work of converting the binary sum
to the BCD sum.
3. Verify the outputs in Table F.2.2.

EEE211L/ETE211L Lab-5 Page 3 of 6


Department of Electrical & Computer Engineering, NSU Digital Logic Design Lab

Figure D.2.1: BCD Adder Circuit

Questions:
1) Explain how the XOR gates and the M bit are being used in the 4-bit adder-subtractor to perform addition
and subtraction operations.
2) Simulate a 4-bit adder in Logisim using basic logic gates. Provide a screenshot of the Logisim circuit
schematic with your report with the two inputs set to decimal 4 and 7.
3) Derive the circuit for the BCD adder (Fig D.2.1). Your explanation should cover the following points:
a) The functions of the top and bottom 7483 4-bit adders.
b) The inputs and outputs of the two adders.
c) The function of the combinational circuit (AND and OR gates) between the two adders.
d) The principles using which the binary sum is being converted to BCD.

EEE211L/ETE211L Lab-5 Page 4 of 6


Department of Electrical & Computer Engineering, NSU Digital Logic Design Lab

F. Data Sheet:
Instructor’s Signature: ............................
Group: Section: Date:

F.1 Experimental data (4-bit Binary Adder-Subtractor):

Operation M A B C4 S4 S3 S2 S1

7+5
4+6
9 + 11
15 + 15
7–5
4–6
11 – 2
15 – 15

Table F.1.1

EEE211L/ETE211L Lab-5 Page 5 of 6


Department of Electrical & Computer Engineering, NSU Digital Logic Design Lab

F.2 Experimental Data (BCD Adder):

Decimal Binary Sum BCD Sum


Value K Z3 Z2 Z1 Z0 C S3 S2 S1 S0
0 0 0 0 0 0
1 0 0 0 0 1
2 0 0 0 1 0
3 0 0 0 1 1
4 0 0 1 0 0
5 0 0 1 0 1
6 0 0 1 1 0
7 0 0 1 1 1
8 0 1 0 0 0
9 0 1 0 0 1
10 0 1 0 1 0
11 0 1 0 1 1
12 0 1 1 0 0
13 0 1 1 0 1
14 0 1 1 1 0
15 0 1 1 1 1
16 1 0 0 0 0
17 1 0 0 0 1
18 1 0 0 1 0
19 1 0 0 1 1

Table F.2.1

Operation A B Overflow Carry Sum

9+0
9+1
9+2
9+3
9+4
9+5
9+6
9+7
9+8
9+9

Table F.2.2

EEE211L/ETE211L Lab-5 Page 6 of 6

You might also like