Scribd
Upload
12 views

Unit-II-ESM-Architecture of PIC Microcontroller 2

The document discusses the architecture of PIC microcontrollers. It is divided into several sections that describe the main components of the PIC microcontroller including the CPU, memory organization, serial communication, interrupts, I/O ports, CCP module, timers, D/A and A/D converters. The CPU contains an ALU, memory unit, control unit, and accumulator. Memory is divided into program memory, data memory, and EEPROM. Serial communication protocols supported are USART, SPI, and I2C. Interrupts and I/O ports provide interfacing with external devices. Timers and converters allow analog and digital signal processing.

Uploaded by

Harish
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
12 views

Unit-II-ESM-Architecture of PIC Microcontroller 2

The document discusses the architecture of PIC microcontrollers. It is divided into several sections that describe the main components of the PIC microcontroller including the CPU, memory organization, serial communication, interrupts, I/O ports, CCP module, timers, D/A and A/D converters. The CPU contains an ALU, memory unit, control unit, and accumulator. Memory is divided into program memory, data memory, and EEPROM. Serial communication protocols supported are USART, SPI, and I2C. Interrupts and I/O ports provide interfacing with external devices. Timers and converters allow analog and digital signal processing.

Uploaded by

Harish
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Unit-II

Architecture of PIC Microcontroller

PIC MICROCONTROLLER ARCHITECTURE: PIC stands for Peripheral


Interface Controller. PIC microcontroller was developed by microchip
technology in 1993. It was developed for supporting PDP computers to control
its peripheral devices and that’s why it was named Peripheral Interface
Controller. PIC microcontrollers are of low cost, very fast and easy for the
programming and execution of program. Their interfacing with other
peripherals is also very easy. PIC Microcontrollers from Microchip Company
are divided into 4 large families.

 First family: PIC10 (10FXXX) called Low End


 Second family: PIC12 (PIC12FXXX) called Mid-Range
 Third family: PIC16 (16FXXX)
 Fourth family: PIC 17/18 (18FXXX)

1. CPU (Central Processing Unit):


PIC microcontroller’s CPU consists of

 Arithmetic logic unit (ALU)


 Memory unit (MU)
 Control unit (CU)
 Accumulator
ALU is used for arithmetic operations and for logical decisions. Memory is
used for storing the instructions after processing. Control unit is used to
control the internal and external peripherals which are connected to the CPU
and accumulator is used for storing the results.

2. MEMORY ORGANIZATION:
PIC microcontroller memory module consists of mainly 3 types of
memories:
 PROGRAM MEMORY:
It contains the written program after we burned it in microcontroller. Program
Counter executes commands stored in the program memory, one after the
other. Pic microcontroller can have 8K words x 14 bits of Flash program
memory that can be electrically erased and reprogrammed. Whenever we
burn program into the micro, we erase an old program and write a new one.

 DATA MEMORY:
It is a RAM type which is used to store the data temporarily in its registers.
The RAM memory is classified into banks. Each bank extends up to 7Fh (128
bytes). Number of banks may vary depending on the microcontroller.
PIC16F84 has only two banks. Banks contain Special Function Registers
(SFR) and General Purpose Registers (GPR). The lower locations of each
bank are reserved for the Special Function Registers and upper locations are
for General Purpose Registers.

General Purpose Registers (GPR):


These registers don’t have any special function. These are used for general
purpose for multiplying, addition or subtraction and then storing the results in
other registers. CPU can easily access the data in these registers.

Special Function Registers (SFR):

These registers are used for special purposes and they cannot be used as
normal registers. Their function is set at the time of manufacturing. They
perform the function assigned to them and user cannot change the function of
SFR. Three important SFRs for programming are:

STATUS register: It changes the bank

PORT registers: It assigns logic values 0 or 1 to the ports

TRIS registers: It is a data direction register for input and output


 DATA EEPROM:
This memory allows storing the variables as a result of burning the written
program. It is readable and writable during normal operation (over the full VDD
range). This memory is not directly mapped in the register file. It is indirectly
addressed through the SFRs. There are six SFRs which are used to read and
write to this memory (EECON1, EECON2, EEDATA, EEDATH, EEADR,
EEADRH).

3. SERIAL COMMUNICATION:
The transfer of one bit of data at time consecutively over a communication
channel is called Serial Communication. There are three protocols of serial
communication:

 USART: It stands for Universal synchronous and Asynchronous


Receiver and Transmitter which provides a serial communication in two
devices. In this protocol data is transmitted and received bit by bit
through a single wire according to the clock pulses. To send and
receive data serially the PIC microcontroller has two pins TXD and
RXD.
 SPI Protocol: SPI stands for Serial Peripheral Interface. It is used to
send data between PIC microcontrollers and other peripherals like
sensors, shift registers and SD cards. Three wire SPI communications
is supported in PIC microcontroller between two devices on a common
clock source. SPI protocol has greater data handling capability than that
of the USART.I2C Protocol: I2C stands for Inter Integrated Circuit, and
this protocol is used to connect low speed devices like microcontrollers,
EEPROMS and A/D converters. PIC microcontroller support two wire
Interface or I2C communication between two devices which can work as
both Master and Slave device.

Serial Communication
4. INTERRUPTS:
There are 20 internal interrupts and three external interrupt sources in PIC
microcontrollers which are related with different peripherals like ADC, USART,
Timers, and CCP etc.
5. I/O PORTS:
Let us take PIC16 series, it consists of five ports, such as Port A, Port B, Port
C, Port D and Port E.

 Port A:This port is 7-bit wide and can be used for both input and output.
The status of TRISA register decided whether it is used as input or
output port.
 Port B:It is an 8-bit port. This port also can be used as input and output.
Moreover in input mode four of its bits are variable according to the
interrupt signals.
 Port C:It is also an 8-bit port and can be used as both input and output
port which is determined by the status of the TRISC register.
 Port D:This 8-bit port, unlike Port A, B and C is not an input/output port,
but is used as acts as a slave port for the connection to
the microprocessor When in I/O mode Port D all pins should have
Schmitt Trigger buffers.
 Port E:It is a 3-bit port which is used as the additional feature of the
control signals to the A/D converter.
6. CCP MODULE:
A CCP module works in the following three modes:

Capture Mode: In this mode time is captured when a signal is arrived,


or we can say that, when the CCP pin goes high it captures the value of
the Timer1.
 Compare Mode: It works same as an analog comparator, which means
that when timer 1’s value reaches some reference value it will give an
output signal.
 PWM Mode: This mode provides a 10 bit resolution pulse and duty
cycle that is programmable.
7. Timers:
Timers and counters are important as timers can tell the time and count. PIC
microcontroller can have up to four timers (depending upon the family)
Timer0, Timer1, Timer2 and Timer3. Timer0 and Timer2 are of 8-bits while the
Timer1 and Timer3 are of 16-bits, which can also be used as a counter. These
timers work according to the selected modes.

8. D/A CONVERTER:
There are no analog outputs in PIC Microcontroller. To get analog output
we have to use external Digital-to-Analog Converter (DAC). It can convert 8
bits of digital number from the eight digital outputs of PIC microcontroller.

9. A/D CONVERTER:

It converts the analog voltage levels to digital voltage values. In PIC


Microcontroller, ADC has 8-channels and has resolution of 10-bit, which
means that if we have to convert an analog voltage between 0V to 5V the
converter will divide it to 2^10 levels (1024 levels). The special function
registers ADCON0 and ADCON1 control the operation of ADC. The converter
stores the lower 8 bits in ADRESL register and the upper bits in the ADRESH
register. Reference voltage of 5V is required for the operation of the converter.

You might also like