BMW CAR-PC
MONITOR MODEL
SPECIFICATION
BMW3/5 SERIES
car-solutions.com
[email protected]
INDEX
Precacution
Specification
System Composition
Product Outline
Connector Pin Assignment
Installaion Guide
OSD (On Screen Display)
How to Use Remote-controller
How to Use I-DRIVE and Navigation RGB
Product Composition
car-solutions.com
[email protected]
PRECACUTION
You must keep the car key taken off from the car
while you work this and finally, connect power of the
vdeo monitor.
When to connect the video monitor cable, you must
keep the power cable taken off.
You must work this at the environment without any
static electricity or damages.
All of process on this installation should be done by
professionals.
You must not break the labels attached on the board,
if it’s broken, no warranty.
When you receive this package you have to check
whether there’s any parts not included and you have
to contact us right away.
Our repair service do not accept any problems caused
by user’s any fault or carelessness.
car-solutions.com
[email protected]
SPECIFICATION
Input Sources
Analog RGB For PC (R, G, B, H, V)
Analog RGB using C-SYNC (R, G, B, Sync On Green)
3 X CVBS (Including Rear View Camera)
OutPut Sources
Serial Type Touch or USB Type Touch Cable
2 X CVBS Output ( Video Out for Headrest Monitor)
Power Consumption
Input Voltage : 9VDC ~ 16VDC
Power Consumption : 11 WATT, MAX
Source Switching Method
by Remote-Controller (For Technician)
by Menu Button of I-DRIVE in the Car(For End-User)
car-solutions.com
[email protected]
SYSTEM COMPOSITION
car-solutions.com
[email protected]
PRODUCT OUTLINE
BMW 3 BMW 5
SERIES SERIES
car-solutions.com
[email protected]
CONNECTOR PIN ASSIGNMENT
If USB type-touch-controller is offered, serial type touch cable is not supported.
car-solutions.com
[email protected]
INSTALLAION GUIDE (1/7)
1. Loose the two pieces of screw(T10) at in-dash board.
2. Carefully, pull a BMW Original Monitor out of
a in-dash board.
car-solutions.com
[email protected]
INSTALLAION GUIDE (2/7)
3. You will find two connectors - LVDS and CAN.
4. Connect a CAN cable.
car-solutions.com
[email protected]
INSTALLAION GUIDE (3/7)
5. Connect a LVDS cable.
car-solutions.com
[email protected]
INSTALLAION GUIDE (4/7)
6. Tie to GND shield of LVDS connector.
*) If you are ignore this, display noise will appear.
car-solutions.com
[email protected]
INSTALLAION GUIDE (5/7)
7. Hardware setting is Completion .
car-solutions.com
[email protected]
INSTALLAION GUIDE (6/7)
8. If you are power on first of all, you will show monitor
selection menu. You must be set up car’s monitor model by
using number key of remote-controller.
car-solutions.com
[email protected]
INSTALLAION GUIDE (7/7)
9. Please take a look at Information Menu of OSD
car-solutions.com
[email protected]
OSD (ON SCREEN DISPLAY)(1/7)
PC RGB MODE CVBS/REAR/S-VIDEO MODE
PICTURE MENU
Brightness
Contrast
Sharpness
Saturation
Hue
car-solutions.com
[email protected]
OSD (ON SCREEN DISPLAY) (2/7)
PC/RGB/ CVBS/REAR/S-VIDEO MODE
COLOR MENU
Color Temperature
Red
Green
Blue
car-solutions.com
[email protected]
OSD (ON SCREEN DISPLAY) (3/7)
PC RGB MODE CVBS/REAR/S-VIDEO MODE
DISPLAY MENU
Horizontal
Vertical
Frequency
Phase
Auto config
car-solutions.com
[email protected]
OSD (ON SCREEN DISPLAY) (4/7)
PC/RGB/ CVBS/REAR/S-VIDEO MODE
SIGNAL MENU
PC
Navigation
This menu is to define state of signal in advance.
S-Video
If navigation is “no”, navigation is not displayed.
Video1
Video2
Rear View
car-solutions.com
[email protected]
OSD (ON SCREEN DISPLAY) (5/7)
PC/RGB/ CVBS/REAR/S-VIDEO MODE
OSD SETTING MENU
Display Mode
Transparence
Parking Guide Line – No, Wide, Narrow
car-solutions.com
[email protected]
OSD (ON SCREEN DISPLAY) (6/7)
PC/RGB/ CVBS/REAR/S-VIDEO MODE
INFORMATION MENU
Part Number - I will explain to next page.
Firmware Ver.
WVGA Setting - If resolution of PC use to 800 * 480, Set up “YES”
Factory Reset
car-solutions.com
[email protected]
OSD (ON SCREEN DISPLAY) (7/7)
PART NUMBER SETTING
1. You will show part number menu. It was aware
as if monitor model is a original monitor.
2. Set up number of tag up your original monitor
or lately number
car-solutions.com
[email protected]
HOW TO USE REMOTE-CONTROLLER
POWER : Long Press – Monitor Selection Menu
0~9 : Number
Source : Source Change
MENU : Activating OSD MENU ON/OFF
MODE : Select.
▲ : UP
▼ : DOWN
◀ : LEFT
▶ : RIGHT
car-solutions.com
[email protected]
HOW TO USE I-DRIVE AND NAVIGATION
RGB
How to Use I-DRIVE
You can use I-DRIVE for source change.
If You press during 2 second, it is working.
How to Use Navigation RGB
The display is been not or distorted at navigation RGB mode,
inform to us about it please.
If you are offered us navigation machine for a short time,
we can support turning service for Navigation RGB display.
And your machine can be setting in OSD Menu for convenience.
car-solutions.com
[email protected]
