SGM3756

38V High Efficiency, Boost WLED Driver

with PWM Control
GENERAL DESCRIPTION FEATURES
With a 40V rated integrated switch FET, the SGM3756 • 1:250 Stable Luminance Dimming
is a boost converter that drives LEDs in series. The • Low EMI by Conducting Ringing Cancelling
boost converter has a 40V, 1.5A internal MOSFET; thus • Improved PSRR for Waveless Lighting
it can drive single or parallel LED strings for small to • Input Voltage Range: 2.7V to 5.5V
large size panel backlighting. • Integrated 40V, 1.5A Current Limit MOSFET
• 38V Open LED Protection for 10 LEDs in Series
The default white LED current is set with the external
• 1.2MHz Switching Frequency
sensor resistor, RSET, and the feedback voltage is
• 200mV Reference Voltage
regulated to 200mV, as shown in the typical application.
• PWM Brightness Control
During the operation, the LED current can be controlled
• Under-Voltage Protection
by using a pulse width modulation (PWM) signal
• Up to 90% Efficiency
applied to the CTRL pin, through which the duty cycle
• Built-in Soft-Start Function
determines the feedback reference voltage. The
• Thermal Shutdown
SGM3756 does not burst the LED current; therefore, it
• -40℃ to +85℃ Operating Temperature Range
does not generate audible noises on the output
• Available in Green TDFN-2×2-6L Package
capacitor. For maximum protection, the device features
integrated open LED protection that disables the
SGM3756 to prevent the output voltage from exceeding
the IC absolute maximum voltage ratings during open APPLICATIONS
LED conditions. Smart Phone Backlighting
The SGM3756 is available in Green TDFN-2×2-6L Tablet Backlighting
package. It operates over an ambient temperature PDAs, Handheld Computers, GPS Receivers
range of -40℃ to +85℃. Portable Media Players, Portable TVs
White LED Backlighting for Small and Media Form Factor
Displays

SG Micro Corp JULY 2016 – REV. A

www.sg-micro.com
 38V High Efficiency, Boost WLED Driver
SGM3756 with PWM Control

PACKAGE/ORDERING INFORMATION
SPECIFIED
PACKAGE ORDERING PACKAGE PACKING
MODEL TEMPERATURE
DESCRIPTION NUMBER MARKING OPTION
RANGE
3756
SGM3756 TDFN-2×2-6L -40℃ to +85℃ SGM3756YTDI6G/TR Tape and Reel, 3000
XXXX

NOTE: XXXX = Date Code.

Green (RoHS & HSF): SG Micro Corp defines "Green" to mean Pb-Free (RoHS compatible) and free of halogen substances. If
you have additional comments or questions, please contact your SGMICRO representative directly.

ABSOLUTE MAXIMUM RATINGS OVERSTRESS CAUTION

Voltage on VIN, CTRL, FB ................................... -0.3V to 6V Stresses beyond those listed may cause permanent damage
Package Thermal Resistance to the device. Functional operation of the device at these or
TDFN-2×2-6L, θJA .................................................... 120℃/W any other conditions beyond those indicated in the
Voltage on SW ................................................... -0.3V to 40V operational section of the specification is not implied.
Junction Temperature ...................................................150℃ Exposure to absolute maximum rating conditions for
Storage Temperature Range ........................ -65℃ to +150℃ extended periods may affect reliability.
Lead Temperature (Soldering, 10sec) ..........................260℃
ESD Susceptibility ESD SENSITIVITY CAUTION
HBM ............................................................................. 2000V This integrated circuit can be damaged by ESD if you don’t
MM ................................................................................. 200V pay attention to ESD protection. SGMICRO recommends that
CDM ............................................................................ 1000V all integrated circuits be handled with appropriate precautions.
Failure to observe proper handling and installation
RECOMMENDED OPERATING CONDITIONS procedures can cause damage. ESD damage can range from
Input Voltage Range ...........................................2.7V to 5.5V subtle performance degradation to complete device failure.
Output Voltage Range ........................................... VIN to 38V Precision integrated circuits may be more susceptible to
Inductor ........................................................... 4.7μH to 10μH damage because very small parametric changes could cause
Input Capacitor ...................................................... 1μF (MIN) the device not to meet its published specifications.
Output Capacitor ................................................. 1μF to 10μF
Operating Temperature Range ....................... -40℃ to +85℃ DISCLAIMER
SG Micro Corp reserves the right to make any change in
circuit design, specification or other related things if
necessary without notice at any time.

SG Micro Corp JULY 2016

www.sg-micro.com
2
 38V High Efficiency, Boost WLED Driver
SGM3756 with PWM Control

PIN CONFIGURATION
(TOP VIEW)

FB 1 6 VIN

NC 2 GND 5 CTRL

GND 3 4 SW

TDFN-2×2-6L

PIN DESCRIPTION
PIN NAME I/O FUNCTION

1 FB I Feedback Pin for Current. Connect the sense resistor from FB to GND.
2 NC - No Connection.
3 GND O Ground.
4 SW I Drain Connection of The Internal Power FET.
5 CTRL I PWM Dimming Signal Input.
6 VIN I Input Supply Pin.

NOTE: I: input; O: output.

TYPICAL APPLICATION
L
VBAT 10μH D
2.7V to 5.5V

CIN
COUT
22μF
1μF
10S1P
6 4
VIN SW

5
SGM3756
CTRL
PWM Dimming 1
Control FB
GND
3 RSET
10Ω

Figure 1. Typical Application

SG Micro Corp JULY 2016

www.sg-micro.com
3
 38V High Efficiency, Boost WLED Driver
SGM3756 with PWM Control

ELECTRICAL CHARACTERISTICS
(VIN = 3.6V, CTRL = VIN, CIN = 22μF, Full = -40℃ to +85℃, typical values are at TA = +25℃, unless otherwise noted.)

PARAMETER SYMBOL CONDITIONS TEMP MIN TYP MAX UNIT

POWER SUPPLY
Input Voltage Range VIN Full 2.7 5.5 V
VIN falling +25℃ 2.2
Under-Voltage Lockout Threshold UVLO V
VIN rising +25℃ 2.3 2.5
UVLO Hysteresis VHYS +25℃ 100 mV
Operating Quiescent Current into VIN IQ VFB = 400mV, no switching +25℃ 0.2 0.35 mA
Shutdown Current ISD CTRL = GND +25℃ 1 μA
BOOST CONVERTER
PWM duty cycle 100% +25℃ 193.5 200 205.3 mV
PWM duty cycle 10% +25℃ 18.5 20.3 22.5 mV
Voltage Feedback Regulation Voltage VREF
PWM duty cycle 1% +25℃ 1.65 2.5 3.25 mV
PWM duty cycle 0.2% +25℃ 0.92 mV
FB Pin Bias Current IFB VFB = 200mV Full 0.001 0.3 μA
VREF Filter Time Constant tREF +25℃ 0.1 ms
N-Channel MOSFET On-Resistance RDS(ON) +25℃ 0.5 0.8 Ω
Switching Frequency fSW Full 0.9 1.2 1.45 MHz
Switching MOSFET Current Limit ILIM +25℃ 1.15 1.5 1.85 A
Output Voltage Over-Voltage Threshold VOVP_SW Full 36 38 39.5 V
CONTROL
CTRL Logic High Voltage VH Full 1.5 V
CTRL Logic Low Voltage VL Full 0.4 V
CTRL Pin Internal Pull-Down Resistor RPD +25℃ 600 kΩ
CTRL Logic Low Time to Shutdown tSD CTRL high to low +25℃ 2.5 ms
PWM Dimming Frequency Range DFR +25℃ 10 100 kHz
Minimum PWM On-Time +25℃ 40 ns
Stable Dimming Range DR +25℃ 0.2 100 %
THERMAL SHUTDOWN
Thermal Shutdown Threshold TSHUTDOWN 160 ℃
Thermal Shutdown Hysteresis THYS 20 ℃

SG Micro Corp JULY 2016

www.sg-micro.com
4
 38V High Efficiency, Boost WLED Driver
SGM3756 with PWM Control

RECOMMENDED COMPONENTS OF TEST CIRCUITS

COMPONENT COMPONENT
INDUCTOR 10μH/CD75NP-100KC 1μF/C2012X7R1H105KT
CAPACITOR
DIODE MBR0540 22μF/C2012X7R1H226KT

TYPICAL PERFORMANCE CHARACTERISTICS

TA = +25℃, L = 10μH, CIN = 22μF, COUT = 1μF, unless otherwise noted.

Open LED Protection Output Ripple at PWM Dimming

200mV/div 10V/div
VFB

2V/div
PWM
AC Coupled

100mV/div
VOUT VOUT
500mA/div

10mA/div
ILED
IL VIN = 3.6V, ILED = 20mA, L = 10μH
VIN = 3.6V, ILED = 20mA, L = 10μH, 8LEDs fPWM = 50kHz, 10LEDs
Time (200μs/div) Time (40μs/div)

Switching Waveform Switching Waveform

20V/div

5V/div
VSW

AC Coupled VSW
100mV/div

500mV/div
VOUT
AC Coupled
VOUT
200mA/div

IL
1A/div
IL

VIN = 3.6V, ILED = 20mA, L = 10μH, 8LEDs VIN = 5V, ILED = 350mA, L = 10μH, 3LEDs

Time (2μs/div) Time (2μs/div)

Start-Up Start-Up
2V/div 10V/div

2V/div 5V/div

VCTRL VCTRL

VOUT

VOUT
500mA/div
200mA/div

IL IL
VIN = 3.6V, ILED = 20mA, L = 10μH, 10LEDs VIN = 5V, ILED = 350mA, L = 10μH, 3LEDs
Time (2ms/div) Time (2ms/div)

SG Micro Corp JULY 2016

www.sg-micro.com
5
 38V High Efficiency, Boost WLED Driver
SGM3756 with PWM Control

TYPICAL PERFORMANCE CHARACTERISTICS (Continued)

TA = +25℃, L = 10μH, CIN = 22μF, COUT = 1μF, unless otherwise noted.

Feedback Voltage vs. PWM Duty Cycle Feedback Voltage vs. PWM Duty Cycle
200 1000
VIN = 3.6V VIN = 3.6V

160 fPWM = 40kHz

fPWM = 40kHz

Feedback Voltage (mV)

Feedback Voltage (mV)

100

120
fPWM = 20kHz
10
80

1
40
fPWM = 20kHz

0 0.1
0 20 40 60 80 100 0.1 1 10 100
PWM Duty Cycle (%) PWM Duty Cycle (%)

Efficiency vs. Output Current Feedback Voltage Production Distribution

100 50
VIN = 3.6V, L = 10μH 100 Samples
45
1 Production Lot
DPWM = 1%
80 40
Percentage of Drivers (%)

6LEDs 4LEDs 35 DPWM = 100%

8LEDs DPWM = 0.2%
Efficiency (%)

60 30
10LEDs 25
40 20 DPWM = 10%

15
20 10
4LEDs (12.8V), 6LEDs (19.2V)
8LEDs (25.6V), 10LEDs (32V) 5
0 0
0 5 10 15 20 25 30 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5
Output Current (mA)
Normalized Feedback Voltage

SG Micro Corp JULY 2016

www.sg-micro.com
6
 38V High Efficiency, Boost WLED Driver
SGM3756 with PWM Control

FUNCTIONAL BLOCK DIAGRAM

L D VOUT
VBAT

CIN COUT

VIN SW
UVLO OVP

Current Limit and

Soft Start

tOFF
Generator

tON

PWM Gate Driver of

Generator Power MOSFET

FB
GM Amplifier
VREF
RSET

CTRL
PWM Dimming
Reference Control

Shutdown
GND

Figure 2. SGM3756 Block Diagram

SG Micro Corp JULY 2016

www.sg-micro.com
7
 38V High Efficiency, Boost WLED Driver
SGM3756 with PWM Control

DETAILED DESCRIPTION
The SGM3756 is a high efficiency, high output voltage Open LED Protection
boost converter in small package size. The device Open LED protection circuitry prevents IC damage as
integrates 40V switch FET and is designed for output the result of white LED disconnection. The SGM3756
voltage up to 38V with a switch peak current limit of monitors the voltage at the SW pin during each
1.5A. Its large driving capability can drive single or switching cycle. The circuitry turns off the switch FET
parallel LED strings for small to large size panel and shuts down the IC when the following condition
backlighting. persists for 8 switching cycles: the SW voltage exceeds
the VOVP threshold. As the result, the output voltage
The SGM3756 operates in a current mode scheme with falls to the level of the input supply. The device remains
quasi-constant frequency. It is internally compensated in shutdown mode until it is enabled by toggling the
for maximum flexibility and stability. The switching CTRL pin.
frequency is 1.2MHz, and the minimum input voltage is
2.7V. During the on-time, the current rises into the Shutdown
inductor. When the current reaches a threshold value The SGM3756 enters shutdown mode when the CTRL
set by the internal GM amplifier, the power switch voltage is logic low for more than 2.5ms. Although the
MOSFET is turned off. The polarity of the inductor internal switch FET does not switch in shutdown, there
changes and forward biases the Schottky diode which is still a DC current path between the input and the
lets the current flow towards the output of the boost LEDs through the inductor and Schottky diode. The
converter. minimum forward voltage of the LED array must exceed
the maximum input voltage to ensure that the LEDs
The SGM3756 topology has also the benefits of remain off in shutdown.
providing very good load and line regulations, and
excellent line and load transient responses. Current Program
The FB voltage is regulated by a low 200mV reference
The feedback loop regulates the FB pin to a low voltage. The LED current is programmed externally
reference voltage (200mV typical), reducing the power using a current-sense resistor in series with the LED
dissipation in the current sense resistor. string(s). The value of the RSET is calculated using
Equation 1:
Soft Start-Up
Soft-start circuitry is integrated into the IC to avoid high VFB
ILED = (1)
inrush current spike during start-up. After the device is RSET
enabled, the GM amplifier output voltage ramps up very
slowly, which ensures that the output voltage rises
Where:
slowly to ensure the smooth start-up and minimize the
ILED = total output current of LED string(s)
inrush current.
VFB = regulated voltage of FB pin
RSET = current sense resistor

The output current tolerance depends on the FB

accuracy and the current sensor resistor accuracy.

SG Micro Corp JULY 2016

www.sg-micro.com
8
 38V High Efficiency, Boost WLED Driver
SGM3756 with PWM Control

DETAILED DESCRIPTION (Continued)

LED Brightness Dimming
VBG
The SGM3756 receives PWM dimming signal at CTRL 200mV
pin to control the total output current. When the CTRL
pin is constantly high, the FB voltage is regulated to CTRL

200mV typically. When the duty cycle of the input PWM VREF
signal is low, the regulation voltage at FB pin is reduced, EA Output
GM
and the total output current is reduced; therefore, it Amplifer

achieves LED brightness dimming. The relationship

between the duty cycle and FB regulation voltage is FB

given by Equation 2:
Figure 3. Programmable FB Voltage Using PWM Signal
VFB = Duty × 200mV + 0.75mV (2)
Under-Voltage Lockout
Where: An under-voltage lockout prevents operation of the
Duty = duty cycle of the PWM signal device at input voltages below typical 2.2V. When the
200mV = internal reference voltage input voltage is below the under-voltage threshold, the
0.75mV = most appreciate maximum from production device is shut down, and the internal switch FET is
statistics turned off. If the input voltage rises by under-voltage
lockout hysteresis, the IC restarts.
Thus, the user can easily control the WLED brightness
by controlling the duty cycle of the PWM signal. The
Thermal Shutdown
PWM frequency is in the range from 10kHz to 100kHz,
If the typical junction temperature of 160 ℃ is
and the recommended minimum PWM duty cycle is
0.1% for no blind dimming. exceeded, an internal thermal shutdown turns off the
device. The device is released from shutdown
As shown in Figure 3, the IC chops up the internal automatically when the junction temperature decreases
200mV reference voltage at the duty cycle of the PWM by 20℃.
signal. The pulse signal is then filtered by an internal
low pass filter. The output of the filter is connected to Operation with CTRL
the GM amplifier as the reference voltage for the FB pin The enable rising edge threshold voltage is 1.5V and
regulation. Therefore, although a PWM signal is used the falling edge threshold voltage is 0.4V. With the
for brightness dimming, only the WLED DC current is CTRL terminal is held below the falling edge threshold
modulated, which is often referred as analog dimming. voltage the device is disabled and switching is inhibited.
This eliminates the audible noise which often occurs The IC quiescent current is reduced in this state. When
when the LED current is pulsed in replica of the input voltage is above the UVLO threshold, and the
frequency and duty cycle of PWM control. Unlike other CTRL terminal voltage is increased above the rising
methods which filter the PWM signal for analog edge threshold, the device becomes active. Switching
dimming, SGM3756 regulation voltage is independent enables and the soft-start sequence initiates.
of the PWM logic voltage level which often has large
variations.

SG Micro Corp JULY 2016

www.sg-micro.com
9
 38V High Efficiency, Boost WLED Driver
SGM3756 with PWM Control

APPLICATION INFORMATION
The SGM3756 device is a step-up DC-DC converter The inductor current peak-to-peak ripple can be
which can drive single or parallel LED strings for small calculated as Equation 4.
to large size panel backlighting.
1
∆IL(P −P) = (4)
Design Requirements  1 1 
L× +  × fS
For this design example, use the parameters listed in V − V V
 OUT IN IN 
Table 1 as the input parameters.

Table 1. Design Parameters Where:

ΔIL(P-P) = inductor peak-to-peak ripple
DESIGN PARAMETER EXAMPLE VALUE L = inductor value
Input Voltage Range 2.7V to 5.5V fS = boost switching frequency
Output, LED Number in A String 10 VOUT = boost output voltage
Output, LED String Number 1 VIN = boost input voltage
Output, LED Current per String 20mA
Therefore, the peak current IL(P) seen by the inductor is
calculated with Equation 5.
Inductor Selection
The selection of the inductor affects power efficiency,
DIL(P −P)
steady state operation as well as transient behavior and IL(P) IL(DC) +
= (5)
loop stability. These factors make it the most important 2
component in power regulator design. There are three
important inductor specifications, inductor value, DC Inductor values can have ±20% tolerance with no
resistance and saturation current. Considering inductor current bias. When the inductor current approaches
value alone is not enough. The inductor value saturation level, its inductance can decrease 20% to
determines the inductor ripple current. Choose an 35% from the 0A value depending on how the inductor
inductor that can handle the necessary peak current vendor defines saturation current. Using an inductor
without saturating. Follow Equation 3 to Equation 4 to with a smaller inductance value forces discontinuous
calculate the inductor's peak current. To calculate the PWM when the inductor current ramps down to zero
current in the worst case, use the minimum input before the end of each switching cycle. This reduces
voltage, maximum output voltage and maximum load the boost converter’s maximum output current, causes
current of application. In a boost regulator, the input DC large input voltage ripple and reduces efficiency. Large
current can be calculated as Equation 3. inductance value provides much more output current
and higher conversion efficiency. For these reasons, a
VOUT × IOUT 4.7μH to 10μH inductor value range is recommended,
IL(DC) = (3) and 4.7μH inductor is recommended for higher than 5V
VIN × η
input voltage by considering inductor peak current and
Where: loop stability.
VOUT = boost output voltage
IOUT = boost output current Schottky Diode Selection
VIN = boost input voltage The SGM3756 demands a low forward voltage,
η = power conversion efficiency high-speed and low capacitance Schottky diode for
optimum efficiency. Ensure that the diode average and
peak current rating exceeds the average output current
and peak inductor current. In addition, the diode
reverse breakdown voltage must exceed the open LED
protection voltage. ONSemi NSR0240 is recommended
for the SGM3756.

SG Micro Corp JULY 2016

www.sg-micro.com
10
 38V High Efficiency, Boost WLED Driver
SGM3756 with PWM Control

APPLICATION INFORMATION (Continued)

Output Capacitor Selection Power Supply Recommendations
The output capacitor is mainly selected to meet the The device is designed to operate from an input voltage
requirement for the output ripple and loop stability. This supply range between 2.7V and 5.5V. This input supply
ripple voltage is related to capacitor capacitance and its must be well regulated. If the input supply is located
equivalent series resistance (ESR). Assuming a more than a few inches from the SGM3756 device,
capacitor with zero ESR, the minimum capacitance additional bulk capacitance may be required in addition
needed for a given ripple can be calculated with to the ceramic bypass capacitors.
Equation 6:
EMI Precaution and Ringing Cancelling
( VOUT − VIN ) × IOUT Careful layout, routing and selection of decoupling
COUT = (6)
VOUT × fS × VRIPPLE components are equal keys to successfully putting a
high energy transmission swing boost backlight driver
Where: together with a waveform sensitive communication
VRIPPLE = peak-to-peak output ripple transceiver into a condensed case. Engineering test on
cellular phones indicates, with shielding case’s
The additional part of the ripple caused by ESR is separation and isolation, that conducting propagation
calculated using: VRIPPLE_ESR = IOUT × RESR. along with power supply trace contributes the most
comparing with the other EMI mechanisms, the
Due to its low ESR, VRIPPLE_ESR could be neglected for coupling and the radiation, even being evaluated with
ceramic capacitors, a 1μF to 10μF capacitor is radiation measurement oriented FCC Part 15 Class-B
recommended for typical application. method. The typical EMI evaluation to narrow band
transmitter is ACLR masking, and TX power limit to
A 1μF output capacitor is suggested for 10/8/6-Series wide band transmitter and RX sensitivity to either
LED applications. For high output current applications narrow band or wide band, which are powers needed to
like 3S8P, larger value output capacitors of 2.2μF is obtain given bit error rate.
recommended to minimize the output ripple.
Ways of conducting EMI suppression include
LED Current Set Resistor propagation limit and reduction of energy swings, such
The LED current set resistor can be calculated by as inserting absorbing ferrite bead in power supply
Equation 1. trace, selecting high self-resonance frequency
decoupling capacitors and ringing cancellation. Figure 4
Thermal Considerations is a simplified circuit showing that ringing is relaxation
The allowable IC junction temperature should be oscillation between diode junction capacitance Cj and
considered under normal operating conditions. This boost inductor L, which injects current swings into
restriction limits the power dissipation of the SGM3756. power supply trace; the 2 voltage waveforms illustrate
The allowable power dissipation for the device can be the difference of circuit performance, with or without
determined by Equation 7: ringing cancellation.

150℃ − TA Normal Switching

PD = (7) Rectifier &
Waveform
θJA Source Plane
L Junction Capacitor
Injection Loopback

Cj
Where:
Conducting

Decoupling
TA is the ambient temperature for the application. Loopback Anti-Ringing
Switching Waveform
θJA is the thermal resistance junction-to-ambient given Decoupling
Capacitor
in Power Dissipation Table. Ground Plane

Figure 4. Ringing Cancellation Illustration

SG Micro Corp JULY 2016

www.sg-micro.com
11
 38V High Efficiency, Boost WLED Driver
SGM3756 with PWM Control

APPLICATION INFORMATION (Continued)

Layout Considerations be kept as short and wide as possible. The output
As for all switching power supplies, especially those capacitor COUT should be put close to VOUT. It is also
high frequency and high current ones, layout is an beneficial to have the ground of COUT close to the GND
important design step. If layout is not carefully done, pin since there is large ground return current flowing
the regulator could suffer from instability as well as between them. FB resistor should be put close to FB
noise problems. Therefore, use wide and short traces pin. When laying out signal ground, it is recommended
for high current paths. The input capacitor CIN needs to to use short traces separated from power ground traces,
be close to VIN pin and GND pin in order to reduce the and connect them together at a single point close to the
input ripple seen by the IC. If possible choose higher GND pin.
capacitance value for it. The SW pin carries high
current with fast rising and falling edge, therefore, the
connection between the SW pin to the inductor should

SG Micro Corp JULY 2016

www.sg-micro.com
12
 PACKAGE INFORMATION

PACKAGE OUTLINE DIMENSIONS

TDFN-2×2-6L

D e
N6

D1
L

E E1

SEE DETAIL A

k
N3 N1
b

TOP VIEW BOTTOM VIEW

1.40

0.65
A

A1
A2 0.80 2.60
SIDE VIEW

0.24 0.65

N2 N1 N2 N1
RECOMMENDED LAND PATTERN (Unit: mm)
DETAIL A
Pin #1 ID and Tie Bar Mark Options

NOTE: The configuration of the Pin #1 identifier is optional,

but must be located within the zone indicated.

Dimensions Dimensions
Symbol In Millimeters In Inches
MIN MAX MIN MAX
A 0.700 0.800 0.028 0.031
A1 0.000 0.050 0.000 0.002
A2 0.203 REF 0.008 REF
D 1.900 2.100 0.075 0.083
D1 1.100 1.450 0.043 0.057
E 1.900 2.100 0.075 0.083
E1 0.600 0.850 0.024 0.034
k 0.200 MIN 0.008 MIN
b 0.180 0.300 0.007 0.012
e 0.650 TYP 0.026 TYP
L 0.250 0.450 0.010 0.018

SG Micro Corp TX00055.001

www.sg-micro.com
 PACKAGE INFORMATION

TAPE AND REEL INFORMATION

REEL DIMENSIONS

TAPE DIMENSIONS

P2 P0

W
Q1 Q2 Q1 Q2 Q1 Q2
B0
Q3 Q4 Q3 Q4 Q3 Q4

Reel Diameter

P1 A0 K0

Reel Width (W1)

DIRECTION OF FEED

NOTE: The picture is only for reference. Please make the object as the standard.

KEY PARAMETER LIST OF TAPE AND REEL

Reel Width
Reel A0 B0 K0 P0 P1 P2 W Pin1
Package Type W1
Diameter (mm) (mm) (mm) (mm) (mm) (mm) (mm) Quadrant
(mm)

DD0001
TDFN-2×2-6L 7″ 9.5 2.30 2.30 1.10 4.00 4.00 2.00 8.00 Q1

SG Micro Corp TX10000.000

www.sg-micro.com
 PACKAGE INFORMATION
CARTON BOX DIMENSIONS

NOTE: The picture is only for reference. Please make the object as the standard.

KEY PARAMETER LIST OF CARTON BOX

Length Width Height

Reel Type Pizza/Carton
(mm) (mm) (mm)

7″ (Option) 368 227 224 8

DD0002

7″ 442 410 224 18

SG Micro Corp TX20000.000

www.sg-micro.com