0% found this document useful (0 votes)
63 views18 pages

RVT70 UQTNWC0 X

This document provides specifications for a 7.0 inch LCD display module with 800x480 resolution and capacitive touch panel. Key details include: - LCD is TFT, transmissive, normally white with 350 cd/m2 surface luminance and 16.7 million colors. - Dimensions are 179.96 x 119 x 7.8 mm with 154.08 x 85.92 mm active area. - Interface is 24-bit RGB. Driver IC is HX8264+HX8664. Backlight uses 21 LEDs. - Capacitive touch panel is projected with 10-18mA current and works with I2C interface.

Uploaded by

Adam Roguszczak
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
63 views18 pages

RVT70 UQTNWC0 X

This document provides specifications for a 7.0 inch LCD display module with 800x480 resolution and capacitive touch panel. Key details include: - LCD is TFT, transmissive, normally white with 350 cd/m2 surface luminance and 16.7 million colors. - Dimensions are 179.96 x 119 x 7.8 mm with 154.08 x 85.92 mm active area. - Interface is 24-bit RGB. Driver IC is HX8264+HX8664. Backlight uses 21 LEDs. - Capacitive touch panel is projected with 10-18mA current and works with I2C interface.

Uploaded by

Adam Roguszczak
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 18

ITEM CONTENTS UNIT

LCD Type TFT/Transmissive/Normally white /


Size 7.0 Inch
Viewing Direction 12:00 (without image inversion) O’ Clock
Gray Scale Inversion Direction 6:00 O’ Clock
LCM (W × H × D ) 179.96 x 119.00 × 7.80 mm3
Active Area (W × H) 154.08 × 85.92 mm2
Dot Pitch (W × H) 0.1926 × 0.179 mm2
Number Of Dots 800 x (RGB) × 480 /
Driver IC HX8264+HX8664 /
Backlight Type 21 LEDs /
Surface Luminance 350 cd/m2
Interface Type 24bit RGB /
Color Depth 16.7M /
Pixel Arrangement RGB Vertical Stripe /
Surface Treatment Clear
Input Voltage 3.3 V
With/Without TSP Projected Capacitive Touch Panel /
Weight 233.60 g

Note 1: RoHS compliant

Note 2: LCM weight tolerance: ± 5%.


Rev.1.1
RVT70UQTNWC0x

REVISION RECORD
REVNO. REVDATE CONTENTS REMARKS
1.0 2015-02-19 Initial Release
1.1 2015-03-31 Surface Treatment data correction

CONTENTS
REVISION RECORD ................................................................................................................................... 2
CONTENTS ............................................................................................................................................... 2
1 MODULE CLASSIFICATION INFORMATION .................................................................................. 3
2 MODULE DRAWING .................................................................................................................... 4
3 ABSOLUTE MAXIMUM RATINGS.................................................................................................. 5
4 ELECTRICAL CHARACTERISTICS .................................................................................................... 5
5 BACKLIGHT CHARACTERISTICS .................................................................................................... 5
6 ELECTRO-OPTICAL CHARACTERISTICS ......................................................................................... 5
7 INTERFACE DESCRIPTION ............................................................................................................ 7
8 LCD TIMING CHARACTERISTICS ................................................................................................. 10
8.1 Clock and data input time diagram ....................................................................................... 10
8.2 Parallel RGB input timing table ............................................................................................. 10
9 CAPACITIVE TOUCH SCREEN PANEL SPECIFICATIONS ............................................................... 11
9.1 Mechanical characteristics .................................................................................................... 11
9.2 Electrical characteristics ........................................................................................................ 11
9.3 Interface description ............................................................................................................. 11
9.4 Interface timing characteristics ............................................................................................. 12
9.5 I2C Read/Write Interface Description ................................................................................... 12
9.6 Communication of the I2C interface with Host ..................................................................... 13
9.7 Touch data read protocol ...................................................................................................... 13
9.8 Data description. ................................................................................................................... 14
9.9 Interrupt Trigger Mode ......................................................................................................... 15
10 ORDERING INFORMATION ........................................................................................................ 16
11 CUSTOMIZATION LEVEL ............................................................................................................. 17
12 RELIABILITY TEST........................................................................................................................ 17
13 LEGAL INFORMATION ................................................................................................................ 18

©
Rev.1.1
RVT70UQTNWC0x

1 MODULE CLASSIFICATION INFORMATION

1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

1. BRAND RV – Riverdi

T – TFT Standard
2. PRODUCT TYPE
F – TFT Custom
35 – 3.5”
43 – 4.3”
3. DISPLAY SIZE
57 – 5.7”

70 – 7.0”

4. MODEL SERIAL NO. U (A-Z)

5. RESOLUTION Q – 800x480 px

T – TFT LCD, RGB


L – TFT LCD, LVDS
6. INTERFACE
S – TFT + Controller SSD1963
F – TFT + Controller FT801

N – No Frame
7. FRAME
F – Mounting Frame

8. BACKLIGHT TYPE W – LED White

9. TOUCH PANEL C – Capacitive Touch Panel

10. VERSION 0x (00, 01, 02, 03, 04, 05)

©
Rev.1.1
RVT70UQTNWC0x

2 MODULE DRAWING

©
Rev.1.1
RVT70UQTNWC0x

3 ABSOLUTE MAXIMUM RATINGS


PARAMETER SYMBOL MIN MAX UNIT
Supply Voltage For LCD Logic VDD -0.3 5.0 V
Supply Voltage For CTP Logic VDD-VSS -0.5 3.6 V
Input Voltage For LCD Logic VIN VSS-0.5 VDD V
LED forward current (each LED) IF - 30 mA
LED reverse voltage (each LED) VR - 1.2 V
Operating Temperature TOP -20 70 °C
Storage Temperature TST -30 80 °C
Humidity RH - 90% (Max 60°C) RH

4 ELECTRICAL CHARACTERISTICS
PARAMETER SYMBOL MIN TYP MAX UNIT NOTES
Supply Voltage For LCD Module VDD 3.0 3.3 3.6 V
Supply Voltage For CTP VDD 2.8 3.3 3.6 V
Input Current (LCD module) IDD - 71.4 - mA
Input Current (CTP) 10 - 18 mA
Input Voltage ' H ' level VIH 0.7VDD - VDD V
Input Voltage ' L ' level VIL 0 - 0.3VDD V
Note : The LED life time is defined as the module brightness decrease to 50% original brightness at
Ta=25°C.

5 BACKLIGHT CHARACTERISTICS
ITEM SYMBOL MIN TYP MAX UNIT
Voltage for LED backlight Vl 9.0 9.6 10.2 V
Current for LED backlight Il 170 180 200 mA
LED Life Time - 30000 50000 - Hrs
Note: The LED life time is defined as the module brightness decrease to 50% original brightness at
Ta=25°C.

6 ELECTRO-OPTICAL CHARACTERISTICS
ITEM SYMBOL CONDITION MIN TYP MAX UNIT REMARK NOTE
Response Time Tr+Tf θ=0° - 20 35 ms FIG 1. 4
Contrast Ratio Cr ∅=0° 400 500 - --- FIG 2. 1
Luminance δ Ta=25 70 75 - % FIG 2. 3
Uniformity WHITE
Surface Luminance Lv - 350 - cd/m2 FIG 2. 2
∅ = 90° 40 50 - deg FIG 3.
∅ = 270° 60 70 - deg FIG 3.
Viewing Angle Range θ ∅ = 0° 60 70 - deg FIG 3. 6
∅ = 180° 60 70 - deg FIG 3.
Red x - - -
y - - -
CIE (x, y) Green x θ=0° - - -
Chromaticity y ∅=0° - - - FIG 2. 5
Blue x Ta=25 - - -
y - - -
White x - 0.280 -
y - 0.310 -

©
Rev.1.1
RVT70UQTNWC0x
Note 1. Contrast Ratio(CR) is defined mathematically as below, for more information see Figure 1.
Average Surface Luminance with all white pixels (P1, P2, P3, P4, P5)
Contrast Ratio =
Average Surface Luminance with all black pixels (P1, P2, P3, P4, P5)

Note 2. Surface luminance is the LCD surface from the surface with all pixels displaying white. For more
information see Figure 2.

Lv = Average Surface Luminance with all white pixels (P1, P2, P3, P4, P5)

Note 3. The uniformity in surface luminance δ WHITE is determined by measuring luminance at each
test position 1 through 5, and then dividing the maximum luminance of 5 points luminance by
minimum luminance of 5 points luminance. For more information see Figure 2.

Minimum Surface Luminance with all white pixels (P1, P2, P3, P4, P5)
δ WHITE =
Maximum Surface Luminance with all white pixels (P1, P2, P3, P4, P5)

Note 4. Response time is the time required for the display to transition from white to black (Rise Time,
Tr) and from black to white (Decay Time, Tf). For additional information see FIG 1. The test equipment
is Autronic-Melchers’s ConoScope series.

Note 5. CIE (x, y) chromaticity, the x, y value is determined by measuring luminance at each test
position 1 through 5, and then make average value.

Note 6. Viewing angle is the angle at which the contrast ratio is greater than 2. For TFT module the
contrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical
or y axis with respect to the z axis which is normal to the LCD surface. For more information see Figure
3.

Note 7. For viewing angle and response time testing, the testing data is based on Autronic-Melchers’s
ConoScope series. Instruments for Contrast Ratio, Surface Luminance, Luminance Uniformity, CIE the
test data is based on TOPCON’s BM-5 photo detector.

Figure 1. The definition of response time

©
Rev.1.1
RVT70UQTNWC0x
Figure 2. Measuring method for Contrast ratio, surface luminance, Luminance uniformity, CIE (x, y) chromaticity

Figure 3.The definition of viewing angle

7 INTERFACE DESCRIPTION
PIN NO. SYMBOL DESCRIPTION REMARK
1 VLED+ Anode Of LED Backlight
2 VLED+ Anode Of LED Backlight
3 VLED- Cathode Of LED Backlight
4 VLED- Cathode Of LED Backlight
5 GND Power Ground
6 VCC Power For Circuit
7 VCC Power For Circuit
8 MODE DE/SYNC Mode Select Note 1
9 DE Data Input Enable
10 VSYNC Vertical Sync Signal
11 HSYNC Horizontal Sync Signal
12 B7 Blue Data (MSB)
13 B6 Blue Data
14 B5 Blue Data
15 B4 Blue Data
16 B3 Blue Data
17 B2 Blue Data
18 B1 Blue Data Note 2
19 B0 Blue Data (LSB) Note 2
20 G7 Green Data (MSB)
21 G6 Green Data

©
Rev.1.1
RVT70UQTNWC0x
22 G5 Green Data
23 G4 Green Data
24 G3 Green Data
25 G2 Green Data
26 G1 Green Data Note 2
27 G0 Green Data (LSB) Note 2
28 R7 Red Data (MSB)
29 R6 Red Data
30 R5 Red Data
31 R4 Red Data
32 R3 Red Data
33 R2 Red Data
34 R1 Red Data Note 2
35 R0 Red Data (LSB) Note 2
36 GND Power Ground
37 DCLK Clock For Input Data Note 3
38 GND Power Ground
39 LR Left / Right Selection Note 4,5,8
40 UD Up / Down Selection Note 4,5,9
41 VCC Power For Circuit
42 VCC Power For Circuit
43 NC No Connection
44 RESET Global Reset Pin Note 6
45 NC No Connection
46 NC No Connection
47 DITHB Dithering Function Note 7
48 GND Power Ground
49 NC No Connection
50 NC No Connection
Note 1: DE/SYNC mode select. Normally (internally) pulled high.
When select DE mode, MODE="1",VS and HS must pull high.
When select SYNC mode, MODE="0",DE must be grounded.
Note 2: When input 18bit RGB data, the two low bits of R, G and B data must be grounded.

Note 3: Data shall be latched at the falling edge of DCLK.

Note 4: Selection of scanning mode.

SET OF SCAN CONTROL INPUT SCANNING DIRECTION


UD LR
GND VCC Up To Down, Left To Right
VCC GND Down To Up, Right To Left
GND GND Up To Down, Right To Left
VCC VCC Down To Up, Left To Right

©
Rev.1.1
RVT70UQTNWC0x
Note 5: Definition of scanning direction.
Refer to the Figure 4.
Figure 4. Definition of scanning direction

Note 6: Global reset pin. Active low to enter reset state. Suggest to connect with an RC reset circuit
for stability. Normally (internally) pulled high.

Note 7: Dithering function enable control, normally (internally) pull high.


When DITHB="1", Disable internal dithering function,
When DITHB="0", Enable internal dithering function,
Note 8: Normally (internally) pull high.
Note 9: Normally(internally) pull low.

©
Rev.1.1
RVT70UQTNWC0x

8 LCD TIMING CHARACTERISTICS


8.1 Clock and data input time diagram
Figure 5. Horizontal input timing diagram.

Figure 6. Vertical input timing diagram

8.2 Parallel RGB input timing table

PARAMETER SYMBOL MIN TYP MAX UNIT


DCLK Frequency Fclk 26.4 33.3 46.8 MHz
VSD Period Time Tv 510 525 650 TH
VSD Display Area Tvd 480 TH
VSD Blanking Tvb 23 TH
VSD Front Porch Tvfp 7 22 147 TH
VSD Pulse Width Tvpw 1 - 20 TH
HSD Pulse Width Thpw 1 - 40 DCLK
HSD Period Time Th 862 1056 1200 DCLK
HSD Display Area Thd 800 DCLK
HSD Blanking Thb 46 DCLK
HSD Front Porch Thfp 16 210 354 DCLK

©
Rev.1.1
RVT70UQTNWC0x

9 CAPACITIVE TOUCH SCREEN PANEL SPECIFICATIONS


9.1 Mechanical characteristics

DESCRIPTION INL SPECIFICATION REMARK


Touch Panel Size 7 inch
Outline Dimension (OD) 179.96mm x 119.00mm Cover Lens Outline
Product Thickness 2.3mm
Glass Thickness 1.1mm
Ink View Area 155.08mm x 87.42mm
Sensor Active Area 156.68mm x 88.52mm
Input Method 5 Finger
Activation Force Touch
Surface Hardness ≥7H

9.2 Electrical characteristics

DESCRIPTION SPECIFICATION
Operating Voltage DC 2.8~3.3V
Power Consumption (IDD) 10~18mA 10~18mA
30~50μA 30~50μA
Interface I2C
Linearity <1.5%
Controller FT5406
I2C address 0x38 (7 bit address)
Resolution 1792*1024

9.3 Interface description

PIN SYMBOL DESCRIPTION REMARK


NO.
1 VSS Power Ground
2 VDD Power For CTP
3 SCL I2C SCL
4 NC
5 SDA I2C SDA
6 NC
7 /RST Reset pin
8 /WAKE Wake signal from host
9 /INT Interrupt signal from CTP
10 VSS Power Ground

©
Rev.1.1
RVT70UQTNWC0x

9.4 Interface timing characteristics

PARAMETER MIN MAX UNIT


SCL Frequency 0 400 kHz
Bus Free Time Between a STOP and START Condition 4.7 / μs
Hold Time (repeated) START Condition 4.0 / μs
Data Setup Time 250 / ns
Setup Time for Repeated START Condition 4.7 / μs
Setup Time for STOP Condition 4.0 / μs

9.5 I2C Read/Write Interface Description


Figure 7. Write N bytes to I2C slave

Figure 8. Set Data Address

Figure 9. Read X bytes from I2C Slave

©
Rev.1.1
RVT70UQTNWC0x

9.6 Communication of the I2C interface with Host


Figure 10. Communication of the I2C interface with Host

9.7 Touch data read protocol

ADDRESS NAME BIT BIT BIT BIT BIT BIT BIT BIT HOST
7 6 5 4 3 2 1 0 ACCESS
00h DEVIDE_MODE Device Mode[2:0] RW
01h GEST_ID Gesture ID[7:0] R
02h TD_STATUS Number of touch points[3:0] R
03h TOUCH1_XH 1st Event Flag 1st Touch X Position[11:8] R
04h TOUCH1_XL 1st Touch X Position[7:0] R
05h TOUCH1_YH 1st Touch ID[3:0] 1st Touch X Position[11:8] R
06h TOUCH1_YL 1st Touch Y Position[7:0] R
07h R
08h R
09h TOUCH2_XH 2nd Event Flag 2nd Touch X Position[11:8] R
0Ah TOUCH2_XL 2nd Touch X Position[7:0] R
0Bh TOUCH2_YH 2nd Touch ID[3:0] 2nd Touch X Position[11:8] R
0Ch TOUCH2_YL 2nd Touch Y Position[7:0] R
0Dh R
0Eh R
0Fh TOUCH3_XH 3rd Event Flag 3rd Touch X Position[11:8] R
10h TOUCH3_XL 3rd Touch X Position[7:0] R
11h TOUCH3_YH 3rd Touch ID[3:0] 3rd Touch X Position[11:8] R
12h TOUCH3_YL 3rd Touch Y Position[7:0] R
13h R
14h R
15h TOUCH4_XH 4th Event Flag 4th Touch X Position[11:8] R
16h TOUCH4_XL 4th Touch X Position[7:0] R
17h TOUCH4_YH 4th Touch ID[3:0] 4th Touch X Position[11:8] R
18h TOUCH4_YL 4th Touch Y Position[7:0] R
19h R
1Ah R
1Bh TOUCH5_XH 5th Event Flag 5th Touch X Position[11:8] R
1Ch TOUCH5_XL 5th Touch X Position[7:0] R
1Dh TOUCH5_YH 5th Touch ID[3:0] 5th Touch X Position[11:8] R
1Eh TOUCH5_YL 5th Touch Y Position[7:0] R

©
Rev.1.1
RVT70UQTNWC0x

9.8 Data description.

DEVICE_MODE
This register is the device mode register, configure it to determine the current
mode of the chip.

ADRESS BIT ADRESS REGISTER NAME DESCRIPTION


00h 6:4 Device Mode [2:0] 000b Work Mode
100b Factory Mode – Read Raw Data

GEST_ID
This register describes the gesture of a valid touch.

ADRESS BIT ADRESS REGISTER NAME DESCRIPTION


01h 7:0 Gesture ID [7:0] Gesture ID
0x10 Move Up
0x14 Move Down
0x18 Move Right
0x48 Zoom In
0x49 Zoom Out
0x00 No Gesture

TD_STATUS
This register is the Touch Data status register.

ADRESS BIT ADRESS REGISTER NAME DESCRIPTION


02h 3:0 Number of Touch Points How Many Points Detected
[2:0] 1-5 is Valid
7:4

TOUCHn_XH(n:1-10)
This register describes MSB of the X coordinate of the nth touch point and the
corresponding event flag.

ADRESS BIT ADRESS REGISTER NAME DESCRIPTION


03h 7:6 Event Flag 00b: Put Down
~ 01b: Put Up
39h 10b: Contact
11b: Reserved
5:4 Reserved
3:0 Touch X Position [11:8] MSB of Touch X Position in Pixels

©
Rev.1.1
RVT70UQTNWC0x

TOUCHn_XL(n:1-10)
This register describes LSB of the X coordinate of the nth touch point.

ADRESS BIT ADRESS REGISTER NAME DESCRIPTION


04h 7:0 Touch X Position [7:0] LSB of the Touch X Position in Pixels
~
3Ah

TOUCHn_YH(n:1-10)
This register describes MSB of the Y coordinate of the nth touch point and
corresponding touch ID.
ADRESS BIT ADRESS REGISTER NAME DESCRIPTION
05h 7:4 Touch ID[3:0] Touch ID of Touch Point
~ 3:0 Touch X Position [11:8] MSB of Touch Y Position in Pixels
3Bh

TOUCHn_YL(n:1-10)
This register describes LSB of the Y coordinate of the nth touch point.

ADRESS BIT ADRESS REGISTER NAME DESCRIPTION


05h 7:0 Touch X Position [7:0] LSB of the Touch Y Position in Pixels
~
3Bh

9.9 Interrupt Trigger Mode


Figure 11. Interrupt triger mode timing

©
Rev.1.1
RVT70UQTNWC0x

10 ORDERING INFORMATION
Three options of rear side adhesive tape are available: double side adhesive tape 0.2 mm with 3M
467MP glue, foam double side adhesive tape 0.5 mm with 3M 467MP glue or without any tape.
There are also two versions of glass color: black and white.

Rear side adhesive tape options:

Double side adhesive tape with 3M Foam double side adhesive tape
Without tape
467MP glue (total thickness 0.2mm) with 3M 467MP glue (total
thickness 0.5mm)

Cover glass color options:

BLACK WHITE

Product options:

PN DESCRIPTION
RVT70UQTNWC00  Double side adhesive tape with 3M 467MP glue
(total thickness 0.2mm)
 Cover glass color- black
RVT70UQTNWC01  Foam double side adhesive tape with 3M 467MP glue
(total thickness 0.5mm)
 Cover glass - black
RVT70UQTNWC02  Without tape
 Cover glass color- black

RVT70UQTNWC03  Double side adhesive tape with 3M 467MP glue


(total thickness 0.2mm)
 Cover glass color- white
RVT70UQTNWC04  Foam double side adhesive tape with 3M 467MP glue
(total thickness 0.5mm)
 Cover glass color- white
RVT70UQTNWC05  Without tape
 Cover glass color- white

©
Rev.1.1
RVT70UQTNWC0x

11 CUSTOMIZATION LEVEL
Beside standard product (BASIC LEVEL), there are two levels of product customization available:

1. ADVANCED LEVEL
2. PROFESSIONAL LEVEL

Basic level - standard version of product with black or white cover glass color.

Advanced level- product with modified cover glass color, company logo or with special transparent
spots for diodes.

Professional level- product with changed panel parameters including glass dimension and shapes.

For more information go to http://riverdi.com/uxtouch/ .

12 RELIABILITY TEST
NO. TEST ITEM TEST CONDITION
1 High Temperature Storage 80±2°C/240hours
2 Low Temperature Storage -30±2°C/240hours
3 High Temperature Operating 70±2°C/240hours
4 Low Temperature Operating -20±2°C/240hours
Temperature Cycle -30±2°C~25~80±2°C × 20 cycles
5 (30min.) (5min.) (30min.)
6 Damp Proof Test 60°C ±5°C × 90%RH/240hours
7 Vibration Test Frequency 10Hz~55Hz
Amplitude of vibration : 1.5mm
Sweep: 10Hz~55Hz~10Hz
X, Y, Z 2 hours for each direction.
8 Package Vibration Test Random vibration :0.15G*G/HZ from5-200HZ,-
6dB/Octave from 200-500HZ of each direction of X.Y.Z
(6 hours for total)
9 Package Drop Test Height:60 cm
1 corner,3 edges,6 surfaces
10 ESD Test ± 2KV, Human body mode,100pF/1500Ω
11 Mechanical Shock 100G 6ms, X, Y, Z 3 times for each
direction

©
Rev.1.1
RVT70UQTNWC0x

13 LEGAL INFORMATION
Riverdi makes no warranty, either expressed or implied with respect to any product, and specifically
disclaims all other warranties, including, without limitation, warranties for merchantability, non-
infringement and fitness for any particular purpose. Information about device are the property of
Riverdi and may be the subject of patents pending or granted. It is not allowed to copy or disclosed
this document without prior written permission.

Riverdi endeavors to ensure that the all contained information in this document are correct but does
not accept liability for any error or omission. Riverdi products are in developing process and published
information may be not up to date. Riverdi reserves the right to update and makes changes to
Specifications or written material without prior notice at any time. It is important to check the current
position with Riverdi.

Images and graphics used in this document are only for illustrative the purpose. All images and graphics
are possible to be displayed on the range products of Riverdi, however the quality may vary. Riverdi is
no liable to the buyer or to any third part for any indirect, incidental, special, consequential, punitive
or exemplary damages (including without limitation lost profits, lost savings, or loss of business
opportunity) relating to any product, service provided or to be provided by Riverdi, or the use or
inability to use the same, even if Riverdi has been advised of the possibility of such damages.

Riverdi products are not fault tolerant nor designed, manufactured or intended for use or resale as on
line control equipment in hazardous environments requiring fail – safe performance, such as in the
operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct
life support machines or weapons systems in which the failure of the product could lead directly to
death, personal injury or severe physical or environmental damage (‘High Risk Activities’). Riverdi and
its suppliers specifically disclaim any expressed or implied warranty of fitness for High Risk Activities.
Using Riverdi products and devices in 'High Risk Activities' and in any other application is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Riverdi from any and all
damages, claims or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise,
under any Riverdi intellectual property rights.

You might also like