Scribd
Upload
25 views

Control-Unit Keypad

This document provides installation instructions for replacing a faulty Control-Unit Keypad/Display component. It describes the supplied and required parts, warns of live voltage hazards, and outlines the step-by-step procedure for removing the old component and installing the new one. System power-up and testing procedures are then referenced in the conclusion.

Uploaded by

Tatiana Romero
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
25 views

Control-Unit Keypad

This document provides installation instructions for replacing a faulty Control-Unit Keypad/Display component. It describes the supplied and required parts, warns of live voltage hazards, and outlines the step-by-step procedure for removing the old component and installing the new one. System power-up and testing procedures are then referenced in the conclusion.

Uploaded by

Tatiana Romero
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Control-Unit Keypad/

Display Effective: October 2006


Installation Instructions

DESCRIPTION ! WARNING
The Control-Unit Keypad/Display is a replacement part used Use caution when connecting power: high-
to replace a faulty component. voltage and AC-powered circuits are present in
the control unit. Be sure to adequately ground
SUPPLIED PARTS the control unit to reduce the risk of electrical
• Kidde Fire Systems, Control-Unit Keypad/Display, shock.
P/N 76-600000-011 a) Disconnect the standby batteries and de-energize
the commercial AC line voltage.
REQUIRED TOOLS b) Slip on a wrist ground strap and clip the ground
• No. 2 Phillips Head Screwdriver. strap to an earth-ground in the enclosure. Do not
• Wrist Ground Strap with Clip work on the printed-circuit board (PCB) unless you
have established a common earth-ground potential
PROCEDURE among yourself, the enclosure, and the PCB.
1. How to Remove the Faulty Keypad/Display. c) Refer to Figure 1. Unscrew the four screws that
attach the keypad / display to its four nylon standoffs.
! WARNING Set the four screws aside.
Two different sources of power can be
connected to the control unit. Disconnect both d) Carefully separate the two headers on the rear, right-
sources of power and critical components such hand side of the keypad / display from the two sets
as control-heads for special extinguishing of mating pins attached to the printed-circuit board.
systems and addressable pilot relays e) Discard the old keypad / display.
controlling facility-power shutoff before
servicing the control unit. The control unit and
associated equipment may be damaged by
removing and/or inserting powered boards and
components, or by connecting cables, while the
control unit is energized.

Nylon Standoffs
Typ (4)
Ke
yp
ad
/D
isp
la Headers
y Mating Pins

Fastening Screws
Typ (4)

Figure 1. Printed-Circuit Board with Keypad/Display


2. How to Install the New Keypad / Display
a) Slip on a wrist ground strap and clip the ground
strap to an earth-ground in the enclosure. Do not
work on the control unit unless you have established
a common earth-ground potential among yourself,
the enclosure, and the PCB.
b) Remove the new display from its shipping carton
and antistatic wrapping.
c) Carefully align the two headers on the keypad /
display with the two sets of mating pins on the PCB.
Press firmly on the right-hand side of the keypad /
display to mate and fully engage the connections
between the headers and mating pins. Refer to
Figure No. 1.
d) Secure the keypad / display to the four nylon
standoffs with the four screws removed in Step 1c).

System Power-up and Testing


Refer to the control unit’s installation, operation, and
maintenance manual for power-up procedures and
recommended system testing.

Kidde is a registered trademark of Kidde-Fenwal, Inc.

This literature is provided for informational purposes only. KIDDE-FENWAL,INC. assumes no


responsibility for the product's suitability for a particular application. The product must be prop-
erly applied to work correctly.
If you need more information on this product, or if you have a particular problem or question,
contact KIDDE-FENWAL INC., Ashland, MA 01721. Telephone: (508) 881-2000

06-236630-001 Rev AB ©2006 Kidde-Fenwal Inc. Printed in USA

You might also like