Huawei OptiXstar HG8145X6 GPON Terminal

Quick Start
Safety Precautions
To use the device properly and safely, read the safety precautions carefully before using the
device and strictly observe these precautions when using the device.
Safety precautions:
 Do not look directly into the optical port without eye protection.
 Keep the device out of the reach of children as the components or accessories may be swallowed.
 The power supply voltage of the device must meet the requirements on the input voltage of the device.
 If the power adapter is damaged and its internal circuit is exposed due to man-made factors, do not touch
the exposed circuit, which may bring safety risks.
 Prevent objects, such as metal, from entering the device through the heat dissipation hole.
 Dry your hands before connecting or disconnecting cables. Stop the device and switch off the power
before connecting or disconnecting cables.
 Switch off the power and disconnect all cables, including the power cable, optical fiber, and network
cable, during periods of lightning activities. The socket-outlet shall be installed near the power adapter
and shall be easily accessible. Before use the power adapter, please check no damage on the adapter.
 Do not lead the strength member of the optical fiber or other metal parts indoors. Do not install network
cables, power adapters or power adapter cables outdoors. Adopting these measures will help prevent
device damage and bodily injuries which are especially prone during thunderstorms.
 Install the device according to the requirements of the manufacturer. To be specific, reserve at least 10 cm
for heat dissipation at the top and four sides of the device, keep the device away from flammable objects,
highly magnetic or electric devices, such as microwave ovens, refrigerators, and mobile phones.
 Do not place any object on the device, so that the device will not be damaged due to overheating or
deformation.
 If an abnormality occurs, for example, liquid entering the device, smoke, unusual sound, and smell, stop
the device immediately, switch off the power, disconnect all cables (such as the power cable, optical cable,
and network cable) to the device, and contact the authorized service center.
 Do not disassemble the device without permission. In the case of a device fault, contact the authorized
service center.
 Dispose of the packing materials, expired batteries, and old or abandoned devices in accordance to local
laws and regulations (recycling them is strongly recommended).
 Do not change the structure, safety design, or performance design of the device without prior
authorization.

Fireproof precautions:
 Keep the device away from large heat source equipment, bare flames, and high-power devices, such as
electric heaters, candles, and blow drier, to eliminate safety risks.
 If there are aged cables or power socket facilities on the power supply line to or near the device, replace
them in time to eliminate safety risks. The power supply voltage of the device must meet the input voltage
requirement.

1
1 Packing List
The following table lists the items in the product package.

Item Quantity
GPON Terminal 1
Power Adapter 1
Ethernet Cable 1

Fiber Patch cord 1

If you find anything missing or damaged, contact the service provider.

2 Product Overview
Product Function
 4 Gigabit Ethernet ports
 1 POTS port
HG8145X6  1 USB port
 2.4G(2*2MIMO)+5G(2*2MIMO)

3 Technical Specifications
 Power adapter input: See the nameplate on the adapter.
 System power supply: See the nameplate on the device.
 Ambient temperature: 0ºC to +40ºC
 Ambient humidity: 5%–95% (non-condensing)

For other technical specifications, see the following table.

Weight Maximum System

GPON Terminal
(Including the Power Adapter) Power Consumption
HG8145X6 About 450 g ≤ 18 W

2
4 Hardware Installations

Step 1 Use an optical fiber to connect the optical port on the ONT.

-The fiber connector connected to the optical port depending on actual conditions.
-To ensure normal use of fibers, make sure that the fiber bend radius is larger than 30 mm.

Step 2 Use a network cable to connect the LAN port to a PC or the Ethernet port on the IP
STB.
Step 3 Use a phone line to connect the TEL port to a phone or fax machine.

Step 4 Use a power adapter to connect the POWER port to the power socket.

Do not use any power adapters that are not in the standard configuration. Otherwise, the device
may be abnormal or unsafe.

Step 5 Use a USB data cable to connect the USB port to the USB storage device.
Step 6 Press the ON/OFF power switch.

Step 7 Press the WLAN switch to enable the WLAN function.

- When the WLAN is off, press the WLAN button (> 3s) and release the button to
open the WLAN.
- When the WLAN is on, press the WLAN button (> 3s) and release the button to
close the WLAN.
Step 8 When the WLAN is on, press the WPS button (> 3s) and release the button to start
Wi-Fi protected setup (WPS) negotiation.

1
The connections between the HG8145X6 and other devices are shown as follows.

Optical port
POTS port
Ethernet port
USB port
Power port
Power switch

Reset
WPS switch
WLAN switch

2
The following table describes the interface of the device:

Port/Button Description
Indicates VoIP telephone ports (RJ-11), used to connecting to
TEL
the ports on telephone sets.

LAN Ethernet RJ-45 interface connecting to an Access Point.

USB USB host port, used to connect to USB storage devices.

POWER Interface connecting to the power adapter.

ON/OFF Push to power on/off the device.

Press the button for a short time to reset the device; press the
Reset button for a long time (longer than 10s) to restore the device to
the default settings and reset the device.

The WPS button, used to enable or disable the Wi-Fi Protected

Setup switch.
WPS Ensure that the function is set in the system software in
advance. After successful setting, press the WPS switch for the
settings to take effect.

The WLAN button, used to enable or disable the WLAN

WLAN
function. By default, this function is enabled.

The optical port is equipped with a rubber plug and is connected

OPTICAL to an optical fiber for transmission.

3
5 Web configuration

5.1 Configure IP Address of Network Card

Configure TCP/IP properties of your network card to Obtain an IP address automatically from
ONT, or set the IP address of the computer with the same network mask of the ONT.

The default management IP address and subnet mask of the GPON terminal are as follows:
-IP address: 192.168.1.1
-Subnet mask: 255.255.255.0

5.2 Internet Settings

Step 1 Open the Internet Explorer (IE) browser and enter http://192.168.1.1/3bb.

Step 2 In the Quick Configuration page that is displayed, enter the user name, password (for surf
internet) and validate code.

After finishing, click Save to apply the internet settings.

4
Step 3 In the Quick Configuration page appears pop-up "Save Completed", click OK to close
this page.

Step 4 In the Quick Configuration page that is displayed, click Close to close this page.

5
5.3 Wireless Settings

Step 1 Open the Internet Explorer (IE) browser and enter http://192.168.1.1.

Step 2 In the login window, enter the user name, password (see the device nameplate for the
default user name and password) and validate code.

Step 3 Click Login. After the password is authenticated, the Web configuration window is
displayed.

-If you do not perform any operations after logging in to the system for five minutes, you will exit the
system and the system automatically returns to the login interface.
-The system will be locked if you input incorrect user name and password three consecutive times. One
minute later, it will be unlocked.
Step 4 In the navigation tree, choose WLAN > 2.4G Basic Network Settings or WLAN > 5G
Basic Network Settings.

Step 5 In the pane, select the Enable WLAN (2.4 GHz or 5 GHz) option box. In the dialog box
that is displayed, set the basic Wi-Fi parameters, including the SSID, authentication
mode, and encryption mode.

-SSID: SSID indicates the name of a wireless network searched by the Wi-Fi terminal (see the device
nameplate for the default SSID).
-WPA PreSharedKey: WPA PreSharedKey indicates the authentication password for the Wi-Fi
terminal to access a wireless network (see the device nameplate for the default WLAN Key).

6
 2.4G Basic Network Settings:

5G Basic Network Settings:

Step 6 Click Apply.

7
6 Indicator Descriptions
Table 1 Indicator status description 1

Indicator Status Description

Steady on The WPS function is enabled.
WPS Blinking A Wi-Fi terminal is accessing the system.
Off The WPS function is disabled.
Steady on The WLAN function is enabled.
WLAN Blinking Data is being transmitted on the WLAN port.
Off The WLAN function is disabled.
The USB port is connected and is working in the
Steady on
host mode, but no data is transmitted.
USB
Blinking Data is being transmitted on the USB port.
Off The USB port is not connected.
The terminal is registered with the softswitch but no
Steady on
service flows are transmitted.
TEL Blinking Service flows are transmitted.
The terminal is not powered on or fails to be
Off
registered to the softswitch.

Steady on The Ethernet connection is in the normal state.

LAN Blinking Data is being transmitted on the Ethernet port.

Off The Ethernet connection is not set up.
LOS/PON See Table 2.
Steady on The ONT is powered on.
POWER
Off The power supply is cut off.

8
Table 2 Indicator status description 2

Status Status
No. Description
PON LOS
The ONT is prohibited by the upper-layer
1 Off Off device, contact the service provider for help.

The ONT attempts to set up a connection

Blinks twice a
2 Off with its upper-layer device.
second

A connection is set up between the ONT and its

3 Steady on Off
upper-layer device.

The ONT is not connected to optical fibers

Blinks once two
4 Off or does not receive optical signals.
seconds

Blinks twice a Blinks twice a The ONT is a rogue terminal, contact the
5
second second service provider for help.

Blinks once two Blinks once two

6 The hardware is faulty.
seconds seconds

If the ONT is not powered on, all indicators are off.