sect.

70 97026
rev. 2015/09/25

Tachometers and Tach/Hourmeters

AT and ATH Series
The AT Series tachometers are rugged, transistorized
instruments with solid-state circuitry for indication
of engine RPM. They are equipped with a bracket
for mounting into a standard 3-3/8 in. (86 mm) dash
mounting hole. A full 270° sweep of the pointer gives
an accurate indication on a large easy–to–read scale,
and the dial can be illuminated for night reading. The
ATH Series models are also equipped with hourmeter to
record the elapsed running time of an engine.
Models are available for alternator, magnetic sensor
or ignition signal. These instruments are designed
to function from pulses generated by an alternator
with 4, 8, 12, 14 or 16 poles on the rotor (3 - 40 PPR). *
The pulses can also be obtained from the ring gear
of an engine by means of an electromagnetic sensor * Products covered by this bulletin comply with European Council
(magnetic pickup). The Murphy magnetic sensor driven electromagnetic compatibility directive 2004/108/EC, except as noted.
models are designed to function with flywheels having
anywhere from 50 to 304 teeth. Ignition signal model Specifications
available for 2 - 10 cylinder, 4 cycle spark-ignited
engines. All models are for negative ground, positive Magnetic Sensor Driven Models
ground or isolated electrical systems and are protected Power Input: 11-28VDC (70mA – 120mA except lamp load)
against reverse polarity hookup. Backlight: 3.4W T-10 wedge base bulb
RPM Input Signal Voltage: 1.5Vrms minimum
All models are powered by a 11-28 VDC battery and Accuracy:
are reverse polarity protected. Tachometer: +2% full scale
These tachometers are specially designed for use on Hourmeter: +0.01% hours, +1 count
Temperature Range: -40 to 180°F (-40 to 82°C) (no permanent damage
truck, marine, industrial or stationary engines. shall occur)
Dial (Face Plate): 270° sweep with white numerals (over black back-
Series Models ground)
Bezel: 304 stainless steel for bright and IS 513 E.E.E. CRCA steel for
ATS Series Magnetic Sensor Signal Tach black
50-304 flywheel teeth 11-28 VDC, 3333 Hz to 20.27 kHz @ 4000 Scale: 0-4000RPM
Case Material: Plastic
RPM Hourmeter Range: 99999.9 hours in 0.1 increments.
ATHS Series Magnetic Sensor Signal Tachometer/Hourme- Alternator Driven and Ignition Driven Models
ter Power Input: 11-28VDC (70mA-120mA except lamp load)
50-304 flywheel teeth 11-28 VDC, 3333 Hz to 20.27 kHz @ 4000 Backlight: 3.4W T-10 wedge base bulb
RPM RPM Input Signal Voltage: V low: 0.5V max, V high: 8.0V min.
Accuracy:
ATA Series Alternator Signal Tachometer Tachometer: +2% full scale
3-40 pulses/engine revolution 12 VDC, 200 Hz to 2667 Hz @ Hourmeter: +0.01% hours, +1 count
Temperature Range: -40 to 180°F (-40 to 82°C) (no permanent damage
4000 RPM shall occur)
Dial (Face Plate): 270° sweep with white numerals (over black back-
ATHA Series Alternator Signal Tachometer/Hourmeter ground)
3-40 pulses/engine revolution 12 VDC, 200 Hz to 2667 Hz @ Bezel: 304 stainless steel for bright and IS 513 E.E.E. CRCA steel for
4000 RPM black
Scale: 0-4000RPM
ATHI Series Ignition Signal Tachometer/Hourmeter Case Material: Plastic
2 - 10 cylinder, 4 cycle engines, 66.7 Hz to 333.3 Hz @ 4000 RPM Hourmeter Range: 99999.9 hours in 0.1 increments.

In order to consistently bring you the highest quality, full-featured products, we reserve the right to change our specifications and designs at any time. MURPHY products and the Murphy
logo are registered and/or common law trademarks of Enovation Controls, LLC. This document, including textual matter and illustrations, is copyright protected by Enovation Controls, LLC,
with all rights reserved. (c) 2015 Enovation Controls, LLC. A copy of the warranty may be viewed or printed by going to http://fwmurphy.com/warranty.
Bezel Styles

Dimensions

How to Order
Order the Tachometer or Tachometer/Hourmeter by model number.

Model Number Description Notes

Magnetic Sensor Tachometer 4000 RPM; 50 - 304 flywheel teeth 11-28 VDC

ATS-40 Bright Stainless Steel Bezel

ATS-40-A Black Stainless Steel Bezel
ATS-40-B SAE Bright Stainless Steel Bezel
ATS-40-C SAE Black Stainless Steel Bezel
Magnetic Sensor Tach/Hourmeter 4000 RPM; 50-304 flywheel teeth 11-28 VDC

ATHS-40 Bright Stainless Steel Bezel

ATHS-40-A Black Stainless Steel Bezel
ATHS-40-B SAE Bright Stainless Steel Bezel
ATHS-40-C SAE Black Stainless Steel Bezel
Alternator Signal Tachometer 4000 RPM; 3 - 40 pulses/rev 11-28 VDC

ATA-40 Bright Stainless Steel Bezel

ATA-40-A Black Stainless Steel Bezel
ATA-40-B SAE Bright Stainless Steel Bezel
Alternator Signal Tach/Hourmeter 4000 RPM; 3 - 40 pulses/rev 11-28 VDC

ATHA-40 Bright Stainless Steel Bezel

ATHA-40-A Black Stainless Steel Bezel
ATHA-40-B SAE Bright Stainless Steel Bezel
ATHA-40-C SAE Black Stainless Steel Bezel
Ignition Signal Tach/Hourmeter 4000 RPM; 1-5 pulses/engine rev

ATHI-40-A Black Stainless Steel Bezel