ENGINE

ACCELERATOR CONTROL SYSTEM

SECTION ACC ACC

E
CONTENTS
PRECAUTION ............................................... 2 Component ............................................................... 3 F
Removal and Installation .......................................... 3
PRECAUTIONS ................................................... 2
Precaution for Supplemental Restraint System SERVICE DATA AND SPECIFICATIONS G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- (SDS) ............................................................. 5
ProCarManuals.com

SIONER" ................................................................... 2
SERVICE DATA AND SPECIFICATIONS
REMOVAL AND INSTALLATION ................ 3 (SDS) .................................................................. 5 H
Accelerator Control ................................................... 5
ACCELERATOR CONTROL SYSTEM ............... 3
I

Revision: August 2007 ACC-1 2008 Frontier

 PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000003220463

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ProCarManuals.com

ness connectors.

Revision: August 2007 ACC-2 2008 Frontier

 ACCELERATOR CONTROL SYSTEM
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION A
ACCELERATOR CONTROL SYSTEM
Component INFOID:0000000003301839
ACC

G
ProCarManuals.com

WBIA0594E J

1. Non-adjustable accelerator pedal assembly

CAUTION: K
• Do not disassemble the accelerator pedal assembly.
• Do not remove the accelerator pedal position sensor from the accelerator pedal bracket.
• Avoid damage from dropping the accelerator pedal assembly during handling. L
• Keep the accelerator pedal assembly away from water.
Removal and Installation INFOID:0000000003301838

M
REMOVAL
1. Disconnect the negative battery terminal.
2. Disconnect the accelerator position sensor electrical connector. N
a. Pull the connector lock back to unlock the connector from the
accelerator pedal position sensor as shown.
b. Pull up on the connector to disconnect it from the accelerator O
pedal position sensor as shown.
3. Remove the two upper and one lower accelerator pedal nuts.
4. Remove the accelerator pedal assembly. P
CAUTION:
• Do not disassemble the accelerator pedal assembly.
• Do not remove the accelerator pedal position sensor from LBIA0333E
the accelerator pedal bracket.
• Avoid damage from dropping the accelerator pedal assembly during handling.
• Keep the accelerator pedal assembly away from water.

Revision: August 2007 ACC-3 2008 Frontier

 ACCELERATOR CONTROL SYSTEM
< REMOVAL AND INSTALLATION >
INSTALLATION
Installation is in the reverse order of removal.
INSPECTION AFTER INSTALLATION
• Check that the accelerator pedal moves smoothly within the speci-
fied range.

Accelerator pedal - total pedal : 48 mm (1.89 in)

applied stroke “A”
• Check that the accelerator pedal smoothly returns to the original
position.
• Perform an electrical inspection of the accelerator pedal position
sensor. Refer to EC-181, "Component Inspection" (QR), EC-638,
"Component Inspection" (VQ).
CAUTION: LBIA0434E

When the harness connector of the accelerator pedal position

sensor is disconnected, perform ″Accelerator Pedal Released Position Learning″. Refer to EC-24,
"Accelerator Pedal Released Position Learning" (QR), EC-464, "Accelerator Pedal Released Position
Learning" (VQ).
ProCarManuals.com

Revision: August 2007 ACC-4 2008 Frontier

 SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS) A
SERVICE DATA AND SPECIFICATIONS (SDS)
Accelerator Control INFOID:0000000003301840
ACC

ACCELERATOR PEDAL
Unit: mm (in) C

F
LBIA0434E

Accelerator pedal - total pedal applied stroke “A” 48 (1.89)

G
ProCarManuals.com

Revision: August 2007 ACC-5 2008 Frontier