International Conference and Utility Exhibition 2014 on Green Energy for Sustainable Development (ICUE 2014)

Jomtien Palm Beach Hotel and Resort, Pattaya City, Thailand, 19-21 March 2014

Modeling of the Solar Photovoltaic Systems to

Fulfill the Energy Demand of the Domestic Sector
of Pakistan using RETSCREEN Software
Aamir Mehmood1*, Furqan Ali Shaikh2*** Adeel Waqas1**,

Abstract--Pakistan is facing severe energy crisis even having a Tc Module temperature

great potential of renewable energy resourcesespecially solar
energy.Pakistan has~2.9 million MW potential of electricity Ta Ambient temperature
generation using solar energy (PV) which is hardly exploited.
Current articleis focused to analyze the implementation of Tr Reference temperature
solar photovoltaic for the domestic sector of Pakistan where ηinv Inverter efficiency
blackouts of 6 to 7 hours are common. Current study is
conducted for six major cities of Pakistan named Karachi, NOCT Nominal operating cell temperature
Islamabad, Lahore, Multan, Quetta and Peshawar occupying β Temperature coefficient for module efficiency
different climatic and geographical positionsusing
RETSCREEN software. Weather information of these cities is
imported from RETSCREEN software database reported by
II. INTRODUCTION
NASA. The role of solar irradiance and load correlation with
respect to ambient conditions is compared and resultant solar
The word energy is central cohesive source behind all
fraction is observed.Modeling work is evaluated on the basis of
NPV, IRR, payback periods and GHG emissions reduction
activities ofuniverse. Nature has gifted this universe with
obtained for pointing out the feasibility of solar PV several non-replenishable energy resources that are enough
implementation leading towards green growth of to accomplish energy requirements of the world but the
Pakistan.Results indicate that implementation of a 5kW need of time is to explore them for efficient utilization.
standalone solar PV system will result in 0.6-0.7tCO2 Energy is considered a key factor in the development of any
reductions in GHG emissions in different regions of Pakistan country. The significance of energy in economic
under prevailing climatic conditions. Installation of solar PV development has been recognized almost universally and
systems will contribute largely in sharing power loadthat will recent studies have shown a strong relationship between the
lead to improved energy situation and reduced environmental
availability of energy and positive economic activity[1].
emissions concerns in the country.
Developing and the emerging economies of the world are
Keywords: Greenhouse gas, RETSCREEN, Renewable energy, facing the dual energy challenge in the current century:
solar photovoltaic. Meeting the needs of billions of people who still lack access
to life line energy while at the same time participating in a
I. ABBREVIATIONS global transition to clean and environment friendly energy
PV Photovoltaic systems.According to International Energy Agency report,
DC Direct Current there would be 53% increase in global primary energy
GHG Greenhouse Gas consumption up to 2030 and 70% of this value is expected
NPV Net Present Value to come from developing nations[2].As concerned with
AC Alternating Current global transition to clean energy resources utilization; fossil
IRR Internal Rate of Return fuels contribute 85-90% to world primary energy supply
NASA National Aeronautics and Space [3]. GHG emissions due to incomplete combustion of these
Administration high carbon content fossil fuels are main drive behind
Kt Clearness index climatic changes. World Health Organization (WHO)
reported that about 1.6 million people die each year due to
ηr Nominal efficiency climatic changes and this number could double by 2020
[4].To counter with energy and environmental issues, the
whole world is searching for clean and environment friendly
renewable energy resources. Although renewable energy
Aamir Mehmood is with Center for Energy Systems, National resources can’t replace the fossil fuel technologies but can
University of Sciences and Technology, Islamabad-44000, Pakistan.
(e-mail: [email protected]) serve as an add on to fulfill the energy needs to a substantial
Furqan Ali Sheikh is with Asian Institute of Technology, Thailand. (e- level [5].Pakistan isenergy deficient nation facing severe
mail: [email protected]) blackout problems due to~4GW [6]electricity deficit
Adeel Waqas is with Center for Energy Systems, National University
of Sciences and Technology, Islamabad-44000, Pakistan. between supply and demandeven though Pakistan has
(e-mail: [email protected]) indefinite potential of renewable energy resources[7] like
solar, wind, hydro, biomass etc. Especially nature has gifted
Pakistan with a location on world map where solar
insolations are among highest [8].There are regions of

uthorized licensed use limited to: NUST School of Electrical Engineering and Computer Science (SEECS). Downloaded on March 27,2023 at 09:03:12 UTC from IEEE Xplore. Restrictions apply
 International Conference and Utility Exhibition 2014 on Green Energy for Sustainable Development (ICUE 2014)
Jomtien Palm Beach Hotel and Resort, Pattaya City, Thailand, 19-21 March 2014
southern Punjab, Sindh and Balochistan on Pakistan map radiations falling over 100m2area in certain southern
where solar irradiance value ranges from 1500W/m2/day to Punjab, Sindh and Balochistan cities[9]. Fig.1 shows the
2750W/m2/day for a 10h-day throughout the economic year solar map of Pakistan developed by NREL and USAID [6]
[9]. It is evident that Pakistan has solar PV potential of [10].
producing 45-83MW electric power/month from solar

Fig. 1. Pakistan Solar Map [6], [10]

PV technology is a proven sourcefor harnessing solar base case electric power load reduction is possible and how
irradiance in from of electricity [11] to meet future energy much GHG emissions can be reduced leading towards green
challenges as PV is among fastest growing industries across growth of Pakistan?
the world [12]. PV technology is being used efficiently in
the remote areas, telecommunication towers, water pumping III. MODELING METHODOLOGY
for irrigation, off-grid cottage/s, highway telephones,
cathodic protection on pipelines, municipal park lighting, A. RETScreen Software
utility peak load shaving, exterior home lighting and many
RETScreen international software is an excel based
other usages[11]. Life cycle performance of PV array is
clean energy project analysis tool developed by Natural
largely affected by solar irradiance value [13] falling on
Resources Canada’s CANMET Energy Diversification
array aperture area, corresponding operating temperature
Research Laboratory (CEDRL)[15] known as Canadian
and azimuth angle [14].
Energy Center. It helps decision makers in evaluating the
In the current study, standalone PV system is analyzed feasibility of certain energy project potential for
for different climatic conditions of Pakistan to fulfill implementation quickly and inexpensively. Software has
domestic energy needs. RETScreen software is used to incorporated all different type of energy especially
model 5kW standalone PV solar system for Karachi, renewable energy related details. Software algorithms can
Islamabad, Lahore, Multan, Quetta and Peshawar. Modeled calculate technical, economic and environmental viability of
system viability is evaluated on the basis of economic different renewable energy, energy efficiency and
determinants like NPV, IRR, equity payback period and cogeneration projects[15], [16] in terms of resultant solar
simple payback period. Technical parameters like role of fraction, NPV, IRR, payback periods, GHG emissions
solar irradiance and resultant solar fraction are also reduction and backup fuel savings[16].
observed. Software calculations also reveal that how much

uthorized licensed use limited to: NUST School of Electrical Engineering and Computer Science (SEECS). Downloaded on March 27,2023 at 09:03:12 UTC from IEEE Xplore. Restrictions apply
 International Conference and Utility Exhibition 2014 on Green Energy for Sustainable Development (ICUE 2014)
Jomtien Palm Beach Hotel and Resort, Pattaya City, Thailand, 19-21 March 2014
B. Climatic Conditions of Selected Cities

RETScreen software developers embedded climatic and

geographical conditions of almost all cities of world map
reported by NASA. Solar irradiance is main attribute among
climatic conditions of certain site that directly corresponds
to life cycle performance of PV system.That’s why
selection of certain location for renewable energy system
installation is an important consideration in terms of its
climatic conditions and geographical information. Cities of
Pakistan selected for current study are Karachi, Islamabad,
Lahore, Multan, Quetta and Peshawar occupying different
geographical locations and corresponding climatic
conditions as shown on Pakistan map in Fig.3[17].Climatic
and geological information of selected sites are mentioned
in Table I.
Fig. 2. Standalone PV Model Locations Selected for Current Study[17]
TABLE.I
CLIMATE INFORMATION OF STANDALONE PV MODEL SITES IN PAKISTAN
Ambient data/ Climatic information of location
Location Karachi Islamabad Lahore Multan Quetta Peshawar
Latitude 24.9oN 33.6oN 31.5oN 30.2oN 30.3oN 34.0oN
Longitude 67.1oE 73.1oE 74.4oE 71.4oE 66.9oE 71.5oE
o o o o
Ambient temperature (Annual) 26.1 C 21.6 C 24.4 C 25.3 C 18.0oC 22.7oC
Daily solar radiations- horizontal (Annual) 5.34 kWh/m2/d 4.02 kWh/m2/d 4.68 kWh/m2/d 5.09 kWh/m2/d 5.46 kWh/m2/d 5.16 kWh/m2/d
Wind Speed (Annual) 3.5 m/s 2.4 m/s 2.1 m/s 3.3 m/s 4.5 m/s 5.0 m/s
Heating Degree-Days o
0 C-d o
659 C-d o
352 C-d 358oC-d 1,346oC-d 555oC-d
Cooling Degree-Days 5,861oC-d 4,236oC-d 5, 240oC-d 5,571oC-d 3,229oC-d 4,644oC-d

NOCT − 20
Purpose of current work is to study the viability of Tc − Ta= (219 + 832 K t ) (2)
800
RETScreen modeled standalone PV system in different
feasibleclimatic and geographical conditions. That’s why
For current study, a mono-Si PV model is selected on
cities pointed on Pakistan map in Fig.2 are selected as
the basis of its parametric characteristics and ease of
climatic conditions also show thatsolar irradiance value
availability. Characteristics features of selected model are
ranges from 4.02-5.46 kWh/m2/d in these cities. Cooling
mentioned in Table II.
degree-days also support these cities for standalone PV
system application with respect to corresponding number of TABLE.II
degree-days, not equally for all sites. PARAMETRIC CHARACTERISTICS OF SELECTED PV MODEL
Property Value
PV Technology Type Mono-Si
C. PV Array Technology Efficiency 19.6%
Nominal Operating temperature 45oC
RETScreen software can simulate a PV system for Temperature Coefficient 0.40%/ oC
different PV technologies like mono-Si, poly-Si, a-Si, Frame Area/PV Module 1.62 m2
Control Method Clamped
CdTe, CIS and spherical-Si. A number of PV models
fabricated by different manufacturers along with their
characteristic parameters like optimum efficiency, nominal D. Standalone PV Model
output temperature and solar collector area are integrated in Standalone PV model represents off-grid system. In such
software database. PV models represented in RETScreen a system, output energy of PV array can be utilized in two
software database are based on Evans [18] work, possible ways; either directly through charge
characterized by its optimum efficiency ( η p ) parameter is controller/battery if connected load is DC or indirectly via
calculated by (1); battery-inverter setup in case of AC loads. Basic standalone
PV system configuration is shown inFig.3.
η p =ηr [1 − β (Tc − Tr )] (1)

And Evan’s formula[18] relates module temperature

(Tc ) and mean monthly ambient temperature ( Ta ) as;

uthorized licensed use limited to: NUST School of Electrical Engineering and Computer Science (SEECS). Downloaded on March 27,2023 at 09:03:12 UTC from IEEE Xplore. Restrictions apply
 International Conference and Utility Exhibition 2014 on Green Energy for Sustainable Development (ICUE 2014)
Jomtien Palm Beach Hotel and Resort, Pattaya City, Thailand, 19-21 March 2014
Basic case study inputs used for modeling standalone PV
system in RETScreen software are mentioned in Table III.

Fig. 3. Standalone PV Model Configuration

Fig. 4. Load Characteristics
E. RETScreen Simulations
TABLE III
RETScreen software pays substantial attention to CASE STUDY INPUT PARAMETERS
Factor Value
intermittent resource-load correlation. User specifies the Days of autonomy 1 Day
load and its type either DC or AC, which is latter converted Battery voltage 12.0 V
into total equivalent DC demand (D) by software algorithms Maximum battery depth of discharge 80%
using following formula[15]; Temperature control method Ambient
Solar tracking mode fixed
PV panel cost 120PKR/Watt
DAC Fuel Cost Escalation Rate 4.10%
DDC=
,equ DDC + (3) Inflation Rate 7.75%
ηinv Discount Rate 9.5%

This total equivalent DC demand is broken down into There are two main parameters assumed while modeling
three parts[15] as; standalone PV system for domestic users;
• Base case power source is grid connected electricity
DDc ,equ = Dmatch + Dcont . + Dbat (4) • Slope of PV module is assumed equal to absolute value of
latitude of location for maximizing the solar irradiance
Among these three parts of total demand; value as system is modeled working year-round.
• Dmatch part of demand has positive intermittent resource-
IV. RESULTS AND DISCUSSION
load correlation
• Dcont . corresponds to steady load having zero intermittent RETScreen software has been developed to figure out
resource-load correlation the viability of a system in terms of its technical parameters
(like number of PV units used and correspondingpower
• Dbat is part of demand having negative intermittent delivered to load), economic determinants (i.e. NPV, IRR,
resource-load correlation equity and simple payback periods) and environmental
constraints (like GHG emissions reduction). RETScreen
For current case study, load characteristics are estimated outcomes are elaborated in three approaches;
to shift the basic loads, which are part of almost every
house, from grid connected electric power to standalone PV • Technical Analysis
system. Load characteristics of current case study for which • Economic Analysis
standalone PV system is modeled are shown in Fig.4. • Emissions Analysis
For shifting load from grid connected to standalone PV
A. Technical Analysis
system, 12V Ni-Cd battery bank with one day of autonomy
is used to provide backup during non-sunny time with 80% In financial terms, technical analysis is a security
maximum suggested depth of discharge. Among case study analysis methodology of observing the changes in past
inputs, financial parameters like fuel cost escalation rate, prices with aim of forecasting future price and volume [21].
inflation rate and discount rate are most important that play But in engineering terms, technical analysis deals with
a significant role in making a certain system feasible or not. parameters of product upon which the efficiency and
In Pakistan, fuel cost escalation rate is 4.10% [19], inflation efficient utilization depends. For standalone PV system’s
rate has become 7.75% [19] while discount rate has been technical analysis, number of PV units required for attaining
raised by State Bank of Pakistan up to 9.5% [19], [20]. 100% power capacity and resultant total power delivered to
load are analyzed.

uthorized licensed use limited to: NUST School of Electrical Engineering and Computer Science (SEECS). Downloaded on March 27,2023 at 09:03:12 UTC from IEEE Xplore. Restrictions apply
 International Conference and Utility Exhibition 2014 on Green Energy for Sustainable Development (ICUE 2014)
Jomtien Palm Beach Hotel and Resort, Pattaya City, Thailand, 19-21 March 2014
Results show that two PV units provide more than NPV and IRR
required 100% power capacity but total power delivered to
load is different for all cities as shown in Fig.5 becauseof Economic performance of a project can be visualized on
difference in solar irradiance value. Thus Output power the basis of its NPV and IRR. Among these two economic
delivered to load is function of solar irradiance value in determinants NPV is preferable criteria accounts for time
corresponding region. Results elaborated inFig.6 depict that value of coming cash flows subsidized at certain discount
higher the value of solar radiations falling on surface, rate[22], can be calculated using (5)[22].
greater the output power of PV system would be.
CFi
−CF0 + ∑ti =1[ ] = NPV (5)
(1 + r )i

IRR is form of return rate that makes NPV of project

equal to zero, can be calculated by modifying (5) as [22];

CFi
−CF0 + ∑ti =1[ = ] NPV
= 0 (6)
(1 + r )i

Where; i= 1, 2, 3,….,t
Fig.7 showsNPV and IRR of standalone PV model. NPV
and IRR show same trend for all cities selected for
currentstudy. Both economic determinants favors the Quetta
city the most while Islamabad least for standalone PV
system application. If we see overall behavior of NPV and
IRR for all cities, these curves are in accordance with daily
solar radiations curve of Fig.6. This means that higher solar
irradince value is causality engine behind larger NPV and
Fig. 5. Number of PV units vs Power Delivered to Load
IRR, making an energy project more feasible.

From individual city point of view, installation of

modeled standalone PV system is feasible for all cities as
NPV is positive and IRR is greater than discount rate for all
selected cities.

Fig. 6. Daily Solar Radiations-Horizontal vs Power Delivered to Load

B. Economic Analysis

Economics deals with production of goods, their

distribution and consumer’s response. Economics of a
certain project can be evaluated on the basis of economic
determinants like NPV, IRR, equity and simple payback
periods.

uthorized licensed use limited to: NUST School of Electrical Engineering and Computer Science (SEECS). Downloaded on March 27,2023 at 09:03:12 UTC from IEEE Xplore. Restrictions apply
 International Conference and Utility Exhibition 2014 on Green Energy for Sustainable Development (ICUE 2014)
Jomtien Palm Beach Hotel and Resort, Pattaya City, Thailand, 19-21 March 2014
C. Emissions Analysis:

GHG emissions are main drive of global warming effect

that is causing serious health issues and even deaths of
thousands of people every year. Main source behind GHG
emissions is incomplete combustion of high carbon content
fossil fuels. That’s why the whole world is searching for
clean and environment friendly energy sources and in this
perspective many protocols have also been set to control
emissions.
Fig. 9 depicts net GHG emissions reduction possible
through installation of single modeled standalone PV
system in selected cities of Pakistan. Fig.10 elaborates detail
emissions analysis and reveals CO2, CH4, N2O emissions
reduction factor in net GHG emissions reduced. Analysis
shows that installation of standalone PV system,one in each
of six selected cities of Pakistan, will lead to 3.8 tCO2
emissionsreduction. Detailed emissions analysis curves in
Fig. 7. NPV and IRR Interpretation Fig.10 also depict that installation of standalone PV system
in a region with higher solar irradiance value would result in
Payback Period larger emissions reduction value.

Payback period is an important economic determinant

with investor’s point of view. Payback period of any project
can be calculated by using a simple mathematical relation
[23];

Payback Period= Cost of Project / Annual Cash flows (7)

Fig.8 depicts the equity payback and simple back period

values for modelled standalone PV system application.
Analysis favours Quetta city the most while Islamabad
least. As a whole, both parameters show same comparative
feasibility trend as NPV and IRR show for selected cites of
Pakistan. Software outcomes also reveal that greater the
value of daily solar radiations falling on surface, lesser the
payback period is. From individual city perspective,
payback period values for all cities are much smaller, even
less the half of suggested project life that is 25 years.
Fig. 9. Net GHG Emissions Reduction

Fig. 8. Payback Periods Interpretation of Standalone PV Model

Fig. 10. Detail Emissions Analysis

uthorized licensed use limited to: NUST School of Electrical Engineering and Computer Science (SEECS). Downloaded on March 27,2023 at 09:03:12 UTC from IEEE Xplore. Restrictions apply
 International Conference and Utility Exhibition 2014 on Green Energy for Sustainable Development (ICUE 2014)
Jomtien Palm Beach Hotel and Resort, Pattaya City, Thailand, 19-21 March 2014
V. CONCLUSION [5] M. H. Sahir and A. H. Qureshi, “Assessment of new and
renewable energy resources potential and identification of
barriers to their significant utilization in Pakistan,” Renew.
A standalone PV system is analyzed using RETScreen Sustain. Energy Rev., vol. 12, no. 1, pp. 290–298, Jan. 2008.
software for six major cities of Pakistan having different [6] M. Amer and T. U. Daim, “Selection of renewable energy
climatic conditions and geographical location. Techno- technologies for a developing county: A case of Pakistan,”
Energy Sustain. Dev., vol. 15, no. 4, pp. 420–435, Dec. 2011.
economic evaluation of modeled system is performedin [7] U. K. Mirza, N. Ahmad, K. Harijan, and T. Majeed, “Identifying
terms of project resultant solar fraction, power delivered to and addressing barriers to renewable energy development in
load, NPV, IRR, equity and simple payback periods. Pakistan,” Renew. Sustain. Energy Rev., vol. 13, no. 4, pp. 927–
Emissionsanalysis is also carried out. Analysis shows that 931, May 2009.
[8] U. K. Mirza, M. M. Maroto-Valer, and N. Ahmad, “Status and
installation of standalone PV system is feasible for all outlook of solar energy use in Pakistan,” Renew. Sustain. Energy
selected cities. But on comparative basis, Quetta city is Rev., vol. 7, no. 6, pp. 501–514, Dec. 2003.
most feasible location while Islamabad capital is least one. [9] S. Adnan, A. Hayat Khan, S. Haider, and R. Mahmood, “Solar
energy potential in Pakistan,” J. Renew. Sustain. Energy, vol. 4,
Results also reveal that feasibility of PV technology for no. 3, p. 032701, 2012.
a certain region is function of solar irradiance value. Higher [10] NREL, “Solar map of Pakistan,” US National Renewable Energy
the value of solar radiations falling on surface is, larger the Laboratory. .
[11] S. Rehman, M. a. Bader, and S. a. Al-Moallem, “Cost of solar
potential of PV technology implementation would be. energy generated using PV panels,” Renew. Sustain. Energy
Replacement of fossil fuels with PV technology will also Rev., vol. 11, no. 8, pp. 1843–1857, Oct. 2007.
lead towards GHG emissions reduction. So, PV system [12] B. Parida, S. Iniyan, and R. Goic, “A review of solar
photovoltaic technologies,” Renew. Sustain. Energy Rev., vol. 15,
application will be helpful in tackling the energy crisis of no. 3, pp. 1625–1636, Apr. 2011.
country and will provide great relief to domestic users from [13] S. Pacca, D. Sivaraman, and G. a. Keoleian, “Parameters
power load-shedding problem. On other hand, PV affecting the life cycle performance of PV technologies and
systems,” Energy Policy, vol. 35, no. 6, pp. 3316–3326, Jun.
technology will also be helpful in green growth of Pakistan. 2007.
[14] A. Mehmood, A. Wasy, A. Waqas, and J. Song, “Development
VI. RECOMMENDATIONS and Computational Flow Analysis of GSM Based Automated
Solar Water Pump,” in feofs2013.org, 2013, pp. 1–8.
[15] D. Thevenard, G. Leng, and S. Martel, “The RETScreen model
PV technology utilization for various purposes can be for assessing potential PV projects,” Conf. Rec. Twenty-Eighth
made more efficient by using maximum power point tracker IEEE Photovolt. Spec. Conf. - 2000 (Cat. No.00CH37036), pp.
(MPPT). MPPT will be helpful in increasing the solar 1626–1629, 2000.
[16] T. Rets. I. C. E. D. S. C. Natural Resources Canada–Canmet
fraction value of system and will also provide economic
ENERGY, “The RETScreen Clean Energy Project Analysis
benefit in terms of reducing number of PV units required to Software 4.0.” .
fulfill energy needs. [17] “Zee-Maps.” [Online]. Available: www.zeemaps.com.
[18] D.L.Evans, “Simplified method for predicting photovoltaic array
output,” Sol. Energy, vol. 27, no. 6, pp. 555–560, 1981.
VII. REFERENCES [19] G. of P. Statistics Division, Pakistan Bureau of Statistics,
“PRESS RELEASE ON INFLATION RATE,” 2013.
[1] A. Aqeel and M. S. Butt, “The relationship between energy [20] S. B. of Pakistan, “Monitory Policy Statement.”
consumption and economic growth in Pakistan,” Asia Pacific [21] C. D.Kirkpatric and Julie R. Dahlquist, Technical Analysis: The
Dev. J., vol. 8, no. 2, pp. 101–109, 2001. Complete Resource for Financial Market Technicians. Financial
[2] V. Applasamy, “Photovoltaic Power System in Malaysia,” pp. Times Press, 2006, p. 3.
214–218, 2011. [22] R. A. Brealey and S. C. Myers, Principles of corporate finance,
[3] C. Ruehl and G. C. Economist, “BP Energy Outlook 2030,” no. 6th Editio. Irwin McGraw-Hill, 2008.
January, 2011. [23] G. J. Leng, “RETScreen interbational: a decision support and
[4] T. Muneer, S. Maubleu, and M. Asif, “Prospects of solar water capacity building tool for assessing potential renewable energy
heating for textile industry in Pakistan,” Renew. Sustain. Energy projects,” 2000.
Rev., vol. 10, no. 1, pp. 1–23, Feb. 2006.

uthorized licensed use limited to: NUST School of Electrical Engineering and Computer Science (SEECS). Downloaded on March 27,2023 at 09:03:12 UTC from IEEE Xplore. Restrictions apply