Scribd
Upload
20 views3 pages

Hay

The document discusses vector analysis and defines four vector operations: addition, scalar multiplication, dot product, and cross product. It provides geometric interpretations of the operations and properties such as commutativity and distributivity. Examples are given to illustrate calculating the dot product of vectors. The cross product is defined using a right-hand rule and generates the area of the parallelogram formed by the two vectors. Problems are presented at the end to prove properties of the dot and cross products.

Uploaded by

Shop đá phong thủy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
20 views3 pages

Hay

The document discusses vector analysis and defines four vector operations: addition, scalar multiplication, dot product, and cross product. It provides geometric interpretations of the operations and properties such as commutativity and distributivity. Examples are given to illustrate calculating the dot product of vectors. The cross product is defined using a right-hand rule and generates the area of the parallelogram formed by the two vectors. Problems are presented at the end to prove properties of the dot and cross products.

Uploaded by

Shop đá phong thủy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

2 CHAPTER 1.

VECTOR ANALYSIS

same magnitude as A but of opposite direction (Fig. I. 2). Note that vectors have magnitude
and direction but not location: a displacement of 4 miles due north from Washington is
represented by the same vector as a displacement 4 miles north from Baltimore (neglecting,
of course, the curvaturé of the earth). On å diagram, therefore, you can slide the arrow
around at will, as long as you don't change its length or direction.
We define four vector operations: addition and three kinds of multiplication.
(i) Addition of two vectors. Place the tail of B at the head of A', the sum, A + B, is the
vector from the tail of A to the head of B (Fig. I .3). (This rule generalizes the obvious
procedure for combining two displacements.) Addition is commutative:

3 miles east followed by 4 miles north gets you to the same place as 4 miles north
followed by 3 miles east. Addition is also associative:

To subtract a vector (Fig. 1.4), add its opposite:

-B

Figure 1.3 Figure 1.4

(ii) Multiplication by a scalar. Multiplication of a vector by a positive scalar a


multiplies the magnitude but leaves the direction unchanged (Fig. 1.5). (If a is negative, the
direction is reversed.) Scalar multiplication is distributive:

(iii) Dot product of two vectors. The dot product of two vectors is defined by

A . B = AB cos o, (1.1)
where 9 is the angle they form when placed tail-to-tail (Fig. 1.6). Note that A • B is itself a
scalar (hence the alternative name scalar product). The dot product is commutative,
A .B = B .A,
1.1. VECTOR ALGEBRA 3

Figure 1.5 Figure 1.6

and distributive,

A . (B =A .B+A . C. (1.2)
Geometrically, A B is the product of times the projection of B along A (or the product of B
times the projection of A along B). If the two vectors are parallel, then A • B = AB. In
particular, for any vector A,
(1.3)
If A and B are perpendicular, then A • B = O,

Example 1.1
Let C A — B (Fig. 1.7), and calculate the dot product of C with itself.
Solution:
C. C (A -B) (A -B) -A A-A .B-B.A+B.B,
C 2 = + B 2 coso. This is the law of
cosines.

(iv) Cross product of two vectors. The cross product of two vectors is defined by

A x g AB sinOfi.
where fi is ä unit vector (vector of length I) pointing perpendicular to the plane of A and B. (I
shall use a hat ( A ) to designate unit vectors.) Of course, there are two directions
perpendicular to any plane: "in" and "out." The ambiguity is resolved by the right-hand rule:
let your fingers point in the direction of the first vector and curl around (via the smaller
angle) toward the second; then your thumb indicates the direction of fi. (In Fig. 1.8 A x B
points into the page; B x A points out of the page.) Note that A x B is itself a vector (hence
the alternative name vector product). The cross product is distributive,
(1.5)
4 but not commutative. In fact,
CHAPTER 1. VECTOR ANALYSIS

Figure 1.7
Figure 1.8
(1.6)

Geometrically, IA x BI is the area of the parallelogram generated by A and B (Fig. 1.8). If


two vectors are parallel, their cross product is zero. In particular,

for any vector A.

Problem 1.1 Using the definitions in Eqs. 1.1 and 1.4, and appropriate diagrams, show that the
dot product and cross product are distributive,
a) when the three vectors are coplanar;
b) in the general case.

Problem 1.2 Is the cross product associative?

If so, prove it; if not, provide a counterexample.

1.1.2 Vector Algebra: Component Form


In the previous section I defined the four vector operations (addition, scalar multiplication,
dot product, and cross product) in "abstract" form—that is, without reference to any
particular coordinate system. In practice, it is often easier to set up Cartesian coordinates x, y,
z and work with vector "components." Let Q, j, and i be unit vectors parallel to the x, y, and z
axes, respectively (Fig. 1.9(a)). An arbitrary vector A can be expanded in terms of these basis
vectors (Fig. 1.9(b)):

You might also like