AQU4518R24v06

DXXXX-690-960/690-960/1695-2690/1695-2690-65/65/65/65-16i/16i/18i/18i-
M/M/M/M-R
EasyRET 2L2H 8-Port Antenna with 4 Integrated RCUs - 2.0m

Antenna Specifications
Electrical Properties
2 x (690 - 960) 2 x (1695 - 2690)
Frequency range (MHz)
690 - 803 790 - 862 824 - 894 880 - 960 1695 - 1990 1920 - 2200 2200 - 2490 2490 - 2690
Polarization +45° , -45°
Electrical downtilt (°) 0 - 10 , continuously adjustable, each band separately 2 - 12, continuously adjustable, each band separately
at mid Tilt 15.0 15.5 15.8 16.0 17.0 17.2 17.7 18.1
Gain (dBi)
over all Tilts 14.7 ±0.5 15.3 ±0.5 15.6 ±0.5 15.8 ±0.5 16.8 ±0.5 17.1 ±0.5 17.5 ±0.5 17.9±0.5
Side lobe suppression for first side
> 16 > 17 > 17 > 17 > 16 > 16 > 16 > 16
lobe above main beam (dB)

Horizontal 3dB beam width (°) 68 ±5 65 ±5 62 ±5 60 ±5 65 ±5 63 ±5 61 ±5 60 ±5

Vertical 3dB beam width (°) 10.5 ±0.9 9.5 ±0.8 9.2 ±0.7 8.5 ±0.7 6.8 ±0.7 5.8 ±0.5 5.3 ±0.4 5.0 ±0.5

VSWR < 1.5

Cross polar isolation (dB) ≥ 28
Interband isolation (dB) ≥ 28
Front to back ratio , ±30° (dB) > 23 > 25 > 26 > 26 > 26 > 27 > 27 > 28
Cross polar ratio (dB) 0° > 17 > 18 > 19 > 20 > 15 > 16 > 17 > 17
Max. effective power per port (W) 500 (at 50℃ ambient temperature) 250 (at 50℃ ambient temperature)
Max. effective power whole
960 (at 50℃ ambient temperature)
antenna (W)
Intermodulation IM3 (dBc) ≤ -153 (2 x 43 dBm carrier)
Impedance (Ω) 50
Grounding DC Ground
1. Values based on NGMN recommendations on Base Station Antenna Standards (BASTA).
2. Electrical datasheet in XML format is available.

Mechanical Properties
68
Antenna dimensions (H x W x D) (mm) 1999 x 429 x 196
Packing dimensions (H x W x D) (mm) 2270 x 515 x 235
Antenna weight (kg) 32.2 (669)

Clamps weight (kg) 4.2 (2 units)

Antenna packing weight (kg) 44.1 (Included clamps)
Mast diameter supported (mm) 50 - 115
Radome material Fiberglass
Radome colour Light grey
1273
1999

Operational temperature (℃) -40 .. +65

Frontal: 555 (at 150 km/h)
Wind load (N) Lateral: 340 (at 150 km/h)
Maximum: 735 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 8 x 4.3-10 Female
Connector position Bottom

Accessories
57

Item Model Description Weight Units per antenna

Unit: mm
Downtilt kit ASMDT0D01 Mechanical downtilt: 0 - 12 ° 2.1 kg 1 (Separate packing)

1
 AQU4518R24v06
DXXXX-690-960/690-960/1695-2690/1695-2690-65/65/65/65-16i/16i/18i/18i-
M/M/M/M-R
EasyRET 2L2H 8-Port Antenna with 4 Integrated RCUs - 2.0m

Antenna Information Management Module (AIMM) Specifications

Properties
RET type Integrated RET
RET protocols* AISG 2.0 / 3GPP
Input voltage range (V) 10 - 30 DC
< 0.5 (when the motor does not work, 12 V)
Power consumption (W) < 4.5 (when the motor is working, 12 V)
< 10 (when the motor is starting up or shutting down, 12 V)
Adjustment time (full range) (s) Typ. 40 (typically, depending on antenna type)
4 x 8 pin connector according to IEC 60130-9
RET connector
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
2.5 (10/350 μs)
Lightning protection (kA)
10 (8/20 μs)
* Please confirm the AISG protocol of primary station is compatible with RET antenna protocol interface. The protocol of RET antenna
software interface is switchable between AISG 2.0/3GPP and AISG 1.1 with a vendor defined command. For more details about protocol
switching function, contact Huawei before system installation.
Standards: EN/IEC 60950-1(Safety), EN/IEC 60950-22(Safety – Equipment installed outdoor), EN 55032 (Emission),
EN/IEC 62368-1(Safety), ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM, RoHS, REACH, WEEE

Integrated RET S/N:

HWxxxx……Ly1
HWxxxx……Lr 1
HWxxxx…...Rr 2

HWxxxx…...Ry2
y1 y2
r - Red y - Yellow r1 r2
L - Left array R - Right array
Pattern sample for reference

690 - 960 MHz 1695 - 2690 MHz

(Lr1/Rr2) (Ly1/Ry2)
NOTE
1. Facilities, such as towers and poles, must bear the weight and wind load of antennas.
2. HUAWEI ‘s standard brackets and accessories must be used for any installation.
3. The antenna working environment must meet the requirements specified in the datasheet.
4. Only qualified personnel are allowed to perform installation. Installation tools and procedures must conform to requirements
described in the antenna installation guide.
5. In the effort to improve our products, all specifications are subject to change without notice.

Huawei Technologies Co., Ltd. Bantian, Longgang District, Shenzhen 518129, P.R.China www.huawei.com/antenna

2 Issue: 2020-11-27