FORM 1.

1 SELF-ASSESSMENT CHECKS

Part III: Assessment and Competency

This self-check Instrument will give the trainer necessary data of information which is
essential in planning training sessions. Please check the appropriate box of your
answer to the questions below.

BASIC COMPETENCIES

CAN I…? YES NO

1. Receive and Respond to Workplace Communication

1.1 Obtain and convey workplace information ✔

1.2 Complete relevant work related documents ✔

1.3 Participate in workplace meeting and discussion ✔

2. Work in Team Environment

2.1 Describe and identify team role and responsibility in a team ✔

2.2 Describe work as a team member ✔

3. Practice Career Professionalism

3.1 Integrate personal objectives with organizational goals ✔

3.2 Set and meet work priorities ✔

3.3 Maintain professional growth and development ✔

4. Practice Occupational Health and Safety

4.1 Identify hazards and risks ✔

4.2 Evaluate hazards and risks ✔

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
4.3 Control hazards and risk ✔

4.4 Maintain OHS awareness ✔

COMMON COMPETENCIES

Can I…? YES NO

1. Apply Appropriate Sealant/Adhesive ✔

2. Move and Position Vehicle ✔

3. Perform Housekeeping ✔

4. Perform Mensuration and Calculation ✔

5. Perform Safety Practices ✔

6. Read, Interpret and Apply Specifications and Manual ✔

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
7. Use and Apply Lubricant/Coolant ✔

8. Perform Shop Maintenance ✔

CORE COMPETENCIES

Can I…? Yes No

1. Service Automotive Battery

1.1 Test automotive battery ✔

1.2 Remove and replace batteries ✔

1.3 Service and charge batteries ✔

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
1.4 Jump-start vehicle ✔

2. Service Ignition System

2.1 Check ignition system ✔

2.2 Perform spark test ✔

2.3 Check ignition coil resistance ✔

2.4 Check ballast resistor ✔

2.5 Adjust contact point clearance (if any) ✔

2.6 Perform ignition wiring installation ✔

2.7 Perform ignition timing ✔

2.8 Repair non-electronic ignition system and/or components ✔

3. Test and Repair Wiring/Lighting System

3.1 Test electrical system ✔

3.2 Repair electrical system ✔

4. Service Starting System

4.1 Test starting system components and identify faults ✔

4.2 Disassemble starter ✔

4.3 Repair/replace and assemble starter components/parts ✔

5. Service Charging System

5.1.1 Test charging system components and identify faults

5.1.2 Disassemble alternator

5.1.3 Repair/replace and assemble alternator components/parts

6. Service Engine Mechanical System

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
6.1 Explain coolant circulation within cooling system ✔

6.2 Check thermostat condition ✔

6.3 Perform leakage test on cooling system ✔

6.4 Repair/replace water pump ✔

6.5 Apply coolant additives ✔

6.6 Explain oil cycle within the engine ✔

6.7 Identify types, classification and application of engine oil ✔

6.8 Overhaul oil pump replace oil filter and change oil ✔

6.9 Explain fuel octane rating ✔

6.10 Identify fuel pump types and classification ✔

6.11 Perform carburetor adjustment ✔

6.12 Overhaul carburetor ✔

6.13 Overhaul turbo charger ✔

6.14 Check turbo charger operation ✔

6.15 Overhaul fuel diesel injector ✔

6.16 Calibrate/install injector ✔

7. Service Clutch System

7.1 Diagnosing clutch failure/problem ✔

7.2 Pulling out and mounting clutch component parts ✔

7.3 Dismantling/installing clutch mechanism ✔

7.4 Overhauling hydraulic clutch mechanism ✔

7.5 Performing clutch failure analysis ✔

7.6 Setting/adjusting clutch system components ✔

7.7 Bleeding clutch hydraulic system ✔

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
8. Service Differential and Front Axle

8.1 Inspect drive shaft and joint ✔

8.2 Dismount and mount differential assembly ✔

8.3 Dismantle and assemble differential parts ✔

8.4 Diagnose differential parts failure ✔

8.5 Set/adjust differential components ✔

8.6 Overhaul rear/front wheel hub ✔

8.7 Analyze king in condition ✔

8.8 Inspect/replace I-beam ✔

9. Service Steering System

9.1 Service steering system ✔

9.2 Diagnose power steering system failure ✔

9.3 Adjust/align tie-rod end to wheel ✔

9.4 Dismantle/install steering components ✔

9.5 Conduct wheel alignment ✔

10. Service Brake System

10.1 Identify the types of hydraulic brake (hydraulic ABS) and its ✔
corresponding components and function

10.2 Explain the operating principle of ABS equip brake ✔

10.3 Interpret schematic diagrams and circuitry ✔

10.4 Performed brake system preventive maintenance ✔

10.5 Diagnose brake system failure ✔

10.6 Performed ABS component testing ✔

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
10.7 Pull-out and disassemble hydraulic brake system component ✔

10.8 Check, assemble and mount hydraulic brake component ✔

10.9 Use appropriate tools and instrument ✔

11. Service Suspension System

11.1 Identify the type of suspension system, component and its ✔

Operating principle (conventional and air suspension)

11.2 Diagnose suspension system failure ✔

11.3 Disassemble and assemble suspension system ✔

(conventional system)

11.4 Inspect and replace suspension system component ✔

(conventional type)

11.5 Service air suspension system ✔

12. Perform Under-chassis Preventive Maintenance

12.1 Check clutch fluid and lines ✔

12.2 Inspect brake system ✔

12.3 Inspect/change transmission/differential gear oil ✔

12.4 Inspect/replace power steering fluid ✔

12.5 Check/refill automatic transmission fluid ✔

12.6 Inspect/bleed air tank ✔

12.7 Check tires and tires pressure ✔

12.8 Check under-chassis body bolts and nuts ✔

13. Overhaul Manual Transmission

13.1 Identify types of transmission and components ✔

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
13.2 Testing transmission ✔

13.3 Pull out and dismount manual transmission and associate ✔

component

13.4 Disassemble manual transmission ✔

13.5 Inspect and check transmission component ✔

13.6 Assemble manual transmission component ✔

13.7 Install, mount manual transmission and associated components ✔

13.8 Test manual transmission performance ✔

Form 1.2 Evidences/Proof of Current Competencies

Part IV: Evidence of Current Competencies acquired related to Job/Occupation

Current Competencies Proof/Evidence Means of Validating

Service Automotive Relevant Training Certificate Submitted an

Battery Certificate of Competency authenticated copy of
training certificate and
COC

Service Ignition System Relevant Training Certificate Submitted an

Certificate of Competency authenticated copy of
training certificate and
COC

Test and Repair Relevant Training Certificate Submitted an

Wiring/Lighting System Certificate of Competency authenticated copy of
training certificate and
COC

Service Starting System

Service Charging Relevant Training Certificate Submitted an

System Certificate of Competency authenticated copy of
training certificate and
COC

Service Engine Relevant Training Certificate Submitted an

Mechanical System authenticated copy of
Date Developed: Document No.:
October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
 Certificate of Competency training certificate and
COC

Service Clutch System Relevant Training Certificate Submitted an

Certificate of Competency authenticated copy of
training certificate and
COC

Service Differential and Relevant Training Certificate Submitted an

Front Axle Certificate of Competency authenticated copy of
training certificate and
COC

Service Steering System Relevant Training Certificate Submitted an

Certificate of Competency authenticated copy of
training certificate and
COC

Service Brake System Relevant Training Certificate Submitted an

Certificate of Competency authenticated copy of
training certificate and
COC

Service Suspension Relevant Training Certificate Submitted an

System Certificate of Competency authenticated copy of
training certificate and
COC

Perform Under-chassis Relevant Training Certificate Submitted an

Preventive Maintenance Certificate of Competency authenticated copy of
training certificate and
COC

Overhaul Manual Relevant Training Certificate Submitted an

Transmission Certificate of Competency authenticated copy of
training certificate and
COC

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
 Training Gap Analysis

Form 1.3 Summary of Current Competencies versus required Competency

Required Units of Current Competency Training/Gaps

Competency/Learning Objectives Requirements

1. Service Automotive Battery

1.1.1 Identify and explain the Identify and explain

operation and safe handling of the operation and safe
different types of battery. handling of different
types of battery

1.1.2 Demonstrate the testing of an Demonstrate the

automotive battery. testing of an
automotive battery

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
1.1.3 Remove and replace batteries Remove and replace
batteries

1.1.4 Service and replace batteries Service and charge

batteries

1.1.5 Demonstrate the procedure of Demonstrate the

jump starting battery procedure of jump
starting battery

2. Service Ignition System

2.1.1 Check and evaluate ignition Check and evaluate

system components ignition system
components

2.1.2 Perform spark test Perform spark test

2.1.3Perform ignition wiring Perform ignition wiring

installation installation

2.1.4 Perform ignition timing Perform ignition timing

3. Service Starting System

3.1.1 Test charging system Test starting

components and identify faults system
components and
identify faults

3.1.2 Disassemble alternator Disassemble

starter

3.1.3 Repair/replace and assemble Repair/replace

alternator components/parts and assemble
alternator
components/parts

4. Service Engine Mechanical System

4.1.1 Explain coolant circulation Explain coolant

within cooling system circulation within

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
 cooling system

4.1.2 Check thermostat condition Check thermostat

condition

4.1.3 Perform leakage test on cooling Perform leakage test on

system cooling system

4.1.4 Repair/replace water pump 4.1.4 Repair/

4.1.5 Apply coolant additives Apply coolant additives

4.1.6 Explain oil cycle within the Explain oil cycle within
engine the engine

4.1.7 Identify types, classification and Identify types,

application of engine oil classification and
application of engine
oil

4.1.8 Overhaul oil pump replace oil Overhaul oil pump

filter and change oil replace oil filter and
change oil

4.1.9 Explain fuel octane rating Explain fuel octane

rating

4.1.10 Identify fuel pump types and Identify fuel pump

classification types and classification

4.1.11 Perform carburetor adjustment Perform carburetor

adjustment

4.1.12 Overhaul carburetor Overhaul carburetor

4.1.13 Overhaul turbo charger Overhaul turbo charger

4.1.14 Check turbo charger operation Check turbo charger

operation

4.1.15 Overhaul fuel diesel injector Overhaul fuel diesel

injector

4.1.16 Calibrate/install injector Calibrate/install

injector

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
5. Service Clutch System

5.5.1 Diagnosing clutch Diagnosing clutch

failure/problem failure/problem

5.1.2 Pulling out and mounting clutch Pulling out and

component parts mounting clutch
component parts

5.1.3 Dismantling/installing clutch Dismantling/installing

mechanism clutch
mechanism

5.1.4 Overhauling hydraulic clutch Overhauling hydraulic

mechanism clutch
mechanism

5.1.5 Performing clutch failure Performing clutch

analysis failure analysis

5.1.6 Setting/adjusting clutch system Setting/adjusting

components clutch system
components

5.1.7 Bleeding clutch hydraulic Bleeding clutch

system hydraulic system

6. Service Differential and Front Axle

6.1.1 Inspect drive shaft and joint Inspect drive shaft and
joint

6.1.2 Dismount and mount Dismount and mount

differential assembly differential assembly

6.1.3 Dismantle and assemble Dismantle and

differential parts assemble differential
parts

6.1.4 Diagnose differential parts Diagnose differential

failure parts failure

6.1.5 Set/adjust differential Set/adjust differential

components components

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
6.1.6 Overhaul rear/front wheel hub Overhaul rear/front
wheel hub

6.1.7 Analyze king in condition Analyze king in

condition

6.1.8 Inspect/replace I-beam Inspect/replace I-beam

7. Service Manual Steering System

7.1.1 Service steering system Service steering system

7.1.2 Diagnose power steering system Diagnose power

failure steering system failure

7.1.3 Adjust/align tie-rod end to Adjust/align tie-rod

wheel end to wheel

7.1.4 Dismantle/install steering Dismantle/install

components steering components

7.1.5 Conduct wheel alignment Conduct wheel

alignment

8. Service Brake System

8.1.1 Identify the types of hydraulic Identify the types of

brake (hydraulic ABS) and its hydraulic brake
corresponding components and (hydraulic ABS) and its
function corresponding
components and
function

8.1.2 Explain the operating principle Explain the operating

of ABS equip brake principle of ABS equip
brake

8.1.3 Interpret schematic diagrams Interpret schematic

and circuitry diagrams and circuitry

8.1.4 Performed brake system Performed brake

preventive maintenance system preventive
maintenance

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
8.1.5 Diagnose brake system failure Diagnose brake system
failure

8.1.6 Performed ABS component Performed ABS

testing component testing

8.1.7 Pull-out and disassemble Pull-out and

hydraulic brake system component disassemble hydraulic
brake system
component

8.1.8 Check, assemble and mount Check, assemble and

hydraulic brake component mount hydraulic brake
component

8.1.9 Use appropriate tools and Use appropriate tools

instrument and instrument

9. Service Suspension System

9.1.1 Identify the type of suspension Identify the type of

system, component and its suspension system,
Operating principle (conventional and component and its
air suspension) Operating principle
(conventional and air
suspension)

9.1.2 Diagnose suspension system Diagnose suspension

failure system failure

9.1.3 Disassemble and assemble Disassemble and

suspension system assemble suspension
(conventional system) system
(conventional system)

9.1.4 Inspect and replace suspension Inspect and replace

system component suspension system
(conventional type) component
(conventional type)

9.1.5 Service air suspension system Service air suspension

system

10. Overhaul Manual Transmission

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2
10.1.1 Identify types of transmission Identify types of
and components transmission and
components

10.1.2 Testing transmission Testing transmission

10.1.3 Pull out and dismount manual Pull out and dismount
transmission and associate manual transmission
component and associate
component

10.1.4 Disassemble manual Disassemble manual

transmission transmission

10.1.5 Inspect and check Inspect and check

transmission component transmission
component

10.1.6 Assemble manual transmission Assemble manual

component transmission
component

10.1.7 Install, mount manual Install, mount manual

transmission and associated transmission and
components associated components

10.1.8 Test manual transmission Test manual

performance transmission
performance

Training Needs

Learning Outcomes Module Title

Testing system and components and

identify faults

Disassemble starter
Service Starting System
Repair/replace and assemble starter
components/parts

Date Developed: Document No.:

October 29, 2016 Checked by: Manila
AUTOMOTIVE SERVICING International Skills
NC II Developed by: Academy (MISA)
Servicing Ignition System Mr. Marvin G. Ibarra Revision #01 2