INFORMATION BULLETIN / PUBLIC - ZONING CODE

REFERENCE NO.: L.A.M.C. 12.21A5 Effective: 01-01-2023

DOCUMENT NO.: P/ZC 2023-001 Revised:
Previously Issued As: P/ZC 2002-001

PARKING DESIGN

I. GENERAL REQUIREMENTS

A. STALL WIDTHS

1. Minimum 8 ft 6 inches wide for standard stalls serving dwelling units.

2. Minimum 8 ft 4 inches wide for all other standard stalls.

3. Minimum 8 ft 0 inches wide for all parallel parking standard stalls.

4. Minimum 7 ft 6 inches wide for all compact stalls.

5. For disabled access stall widths and other requirements, refer to Information Bulletin P/BC
2023-084.

6. Stall widths must be increased 10 inches for obstructions, except for stalls serving single
family dwellings and duplexes, as shown in Figures 8 & 9 and shall be increased for end
stall conditions as shown in Figures 2 and 3 in section N. For purposes of determining
increases for obstructions, property lines shall be considered as obstructions. No increase
for obstructions is required for parallel parking stalls.

B. STALL DEPTHS

1. Minimum 18 feet deep for all standard stalls.

2. Minimum 15 feet deep for all compact stalls.

3. Minimum 26 feet deep for all standard parallel stalls and 30 feet deep for end parallel stalls.

4. Minimum 23 feet deep for all compact parallel stalls and 27 feet deep for end parallel stalls.

C. COMPACT PARKING SPACES PERMITTED

In parking areas or garages containing 10 or more spaces for other than dwelling uses, up to 40%
of the total required parking spaces and 100% of the non-required parking spaces may be
compact. For dwelling uses, all parking stalls in excess of one stall per unit may be compact.
Unless specified otherwise, required guest parking spaces may be compact spaces.

D. ACCESS AISLE AND PARKING BAY WIDTHS

1. The basic access aisle and parking bay widths for compact and standard stalls are shown
in Tables 1 through 6.

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 1 of 29
 P/ZC 2023-001

2. Parking bay dimensions shall be determined using the required basic stall width before
required increases for obstructions. Where required and non-required stalls are intermixed
in a bay, the width of the bay shall be the larger of the bay widths shown in the tables for
the required and non-required stalls. Where single access is provided for both entrance
and exit to a parking bay and the bay contains 25 stalls or less, the bay may be designed
using one-way traffic tables. Where the number of stalls exceeds 25 and single access for
entrance is provided, the bay widths shall be determined using the two-way traffic tables.

E. TANDEM PARKING STALLS

1. Tandem parking stalls are permitted in public garages and public parking areas providing
an attendant. A “Covenant and Agreement to Provide Parking Attendant” will be required.

2. Tandem stalls are permitted in private parking garages and private parking areas provided:

a. At least one parking stall per dwelling unit and all stalls required for any guest
parking shall be individually and easily accessible.

b. At least one standard stall per dwelling unit shall be provided.

3. Tandem parking shall be limited to a maximum of two cars in depth, in a private garage
or private parking area, except for additional parking required in accordance with Section
12.21A17(h) or 12.21C10(g)(4).

4. When determining access aisle widths for tandem parking having both standard and
compact stalls in tandem, the aisle widths for standard stalls shall be used.

F. PARKING STALL LOCATION

1. Each parking stall shall be so located that no automobile is required to back into any public
street or sidewalk to leave the parking stall, parking bay, or driveway, except where such
parking stalls, parking bays, or driveways serve not more than two dwelling units and where
the driveway access is to a street other than a major or secondary highway.

2. No automobile parking space shall be provided or maintained within the required front yard
of an A or R zoned lot except for additional parking provided in accordance with Sections
12.21A17(h) or 12.21C10(g)(2).

3. No parking stall may be located within a 5 foot side yard along the side street lot line of an
A or R zoned corner lot.

G. DRIVEWAY WIDTHS AND LOCATIONS

1. Department of Transportation approval for the location of the driveways shall be obtained
on lots located in a P (including any combination with an A or R Zone) or PB Zone, for all
residential driveways serving two or more dwelling units which front on major and
secondary highways and for all new driveways serving all other uses.

2. 9 ft. minimum in the A, RE, RS, R1, RU, RZ, R2, RMP and RW Zones.

3. 10 ft. minimum in all other zones and when serving an apartment house in the R2 Zone.

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 2 of 29
 P/ZC 2023-001

4. 19 ft. minimum when serving more than 25 cars or, in lieu thereof, there shall be two 10 ft.
minimum wide driveways.

5. Not more than 50% of a required front yard shall be designed, improved or used for access
driveways unless the lot is developed with a building meeting the requirements of Section
12.08.3B1 (RZ Zone requirements).

H. SLOPES FOR DRIVEWAYS, RAMPS AND STALLS

1. 20% maximum slope on driveway or ramp.

2. 10% maximum cross slope of a driveway or ramp.

3. 6.67% maximum slope in any direction in a parking stall.

4. Transition slopes are required when the slope of the driveway or ramp exceeds 12.5%.
See Figures 11A and 11B for acceptable transition slope designs.

I. GARAGE DESIGN

1. DOOR OPENING WIDTHS

a. The required garage door opening width shall be increased in the event the stall
widths are increased in order to accommodate a reduced access aisle width.

b. The required garage door opening shall be equal to the required stall width less 8
inches for a one car garage and the sum of the required stall widths, less 16 inches
for a two car garage.

Exception: The required garage door opening width for a one car garage
shall be 8 feet minimum. The required garage door opening width for a two
car garage shall be 16 feet minimum.

c. The required garage door opening width for all other garages shall be equal to the
required driveway width or the sum of the stall widths whichever is greater.

2. CLEAR HEIGHT IN GARAGE

a. All parking garages shall have an unobstructed headroom clearance of not less than
7 feet above the finished floor to any ceiling, beam, pipe or similar obstruction.

b. All entrances to and vertical clearances within parking structures shall have a
minimum vertical clearance of 8 feet 2 inches where required for accessibility to
parking spaces for persons with physical disabilities.

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 3 of 29
 P/ZC 2023-001

J. PAVING, LANDSCAPING, AND CAR STOPS

1. Every parking area and parking garage including access driveways thereto, shall be paved
with hard, durable asphaltic paving which has been mixed at a plant and is at least two
inches thick after compaction or with portland cement paving at least three inches thick.
Exception: Access driveways to the areas referenced above may be paved with a
permeable material such as pavers, porous concrete, a combination of 45% concrete and
55% holes filled with grass distributed uniformly (commonly known as grasscrete), or any
material deemed equivalent by the Department of City Planning.

2. All areas shall have appropriate bumper guards, wheel stops, steel posts, walls, curbs,
suitable landscaping, or other installations adequate to prevent vehicles from parking or
maneuvering on those portions of a lot upon which a driveway or parking area is prohibited,
or into a public right of way, or where those portions of a lot are needed to prevent
encroachment on walkways or adjoining properties.

3. All portions of a required front yard shall be landscaped as required by LAMC Section
12.21C1(g). A City Planning approval is required for all such landscaped areas in the RD,
R3, RAS3, R4, RAS4, R5, or C zones, and when landscaping is required by any other
provision of the LAMC.

K. INTERNAL CIRCULATION

All portions of a public parking area or public garage shall be accessible to all other portions
thereof without requiring the use of any public street, unless the Department of Transportation
determines that such use is not detrimental to the flow of traffic.

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 4 of 29
 P/ZC 2023-001

TABLE 1: STANDARD CARS - PARKING BAY WIDTHS FOR ONE-WAY TRAFFIC *

AND DOUBLE LOADED AISLES, BASED ON CHART NO. 1 IN ORDINANCE NO. 142,306

Parking 8'-4" 8'-6" 8'-8" 8'-10" 9'-0" 9'-2" 9'-4"

Angle Stalls Stalls Stalls Stalls Stalls Stalls Stalls
30 43'-0" 43'-0" 43'-0" 43'-0" 43'-0" 43'-0" 43'-0"
32.5 44'-2" 44'-2" 44'-2" 44'-2" 44'-2" 44'-2" 44'-2"
35 45'-3" 45'-3" 45'-3" 45'-3" 45'-3" 45'-3" 45'-3"
37.5 46'-3" 46'-3" 46'-3" 46'-3" 46'-3" 46'-3" 46'-3"
40 47'-4" 47'-0" 47'-0" 47'-0" 47'-0" 47'-0" 47'-0"
42.5 48'-10" 48'-4" 47'-10" 47'-8" 47'-8" 47'-8" 47'-8"
45 50'-3" 49'-10" 49'-5" 49'-0" 48'-7" 48'-5" 48'-5"
47.5 51'-6" 51'-1" 50'-8" 50'-3" 49'-10" 49'-5" 49'-0"
50 52'-8" 52'-3" 51'-10" 51'-5" 51'-0" 50'6" 50'-1"
52.5 53'-8" 53'-3" 52'-10" 52'-5" 52'-0" 51'-6" 51'-1"
55 54'-7" 54'-2" 53'-9" 53'-4" 52'-11" 52'-5" 52'-0"
57.5 55'-6" 55'-0" 54'-7" 54'-1" 53'-8" 53'-2" 52'-9"
60 56'-5" 55'-11" 55'-5" 55'-0" 54'-8" 54'-0" 53'-7"
62.5 57'-4" 56'-10" 56'-4" 55'-10" 55'-4" 54'-9" 54'-5"
65 58'-2" 57'-8" 57'-2" 56'-8" 56'-2" 55'-8" 55'-2"
67.5 58'-10" 58'-3" 57'-9" 57'-3" 56'-9" 56'-3" 55'-9"
70 59'-7" 59'-0" 58'-6" 58'-0" 57'-6" 57'-0" 56'-6"
72.5 60'-3" 59'-8" 59'-2" 58'-7" 58'-1" 57'-7" 57'-1"
75 60'-11" 60'-4" 59'-9" 59'-2" 58'-8" 58'-1" 57'-7"
77.5 61'-7" 61'-0" 60'-5" 59'-10" 59'-3" 58'-8" 58'-2"
80 62'-2" 61'-7" 61'-0" 60'-5" 59'-10" 59'-3" 58'-8"
82.5 62'-8" 62'-0" 61'-5" 60'-10" 60'-3" 59'-8" 59'-1"
85 63'-2" 62'-8" 61'-11" 61'-3" 60'-8" 60'-1" 59'-6"
87.5 63'-7" 62'-11" 62'-3" 61'-7" 61'-0" 60'-4" 59'-9"
90 64'-0" 63'-4" 62'-8" 62'-0" 61'-4" 60'-8" 60'-0"
* NOTE: All values on this table are for required parking stalls. To determine parking bay widths for
non-required stalls, merely use a column showing a stall width dimension that is 4 inches more.
The values above the darkened lines are governed by minimum aisle width.
The stall widths (8'-6", 8'-10", and 9'-2") are not shown in the ordinance, but are available for
use.

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 5 of 29
 P/ZC 2023-001

TABLE 2: STANDARD CARS - PARKING BAY WIDTHS FOR ONE-WAY TRAFFIC

AND SINGLE LOADED AISLES, BASED ON CHART NO. 2 IN ORDINANCE NO. 142,306 *
Parking 8'-4" 8'-6" 8'-8" 8'-10" 9'-0" 9'-2" 9'-4"
Angle Stalls Stalls Stalls Stalls Stalls Stalls Stalls
30 27'-6" 27'-6" 27'-6" 27'-6" 27'-6" 27'-6" 27'-6"
32.5 28'-1" 28'-1" 28'-1" 28'-1" 28'-1" 28'-1" 28'-1"
35 28'-7" 28'-7" 28'-7" 28'-7" 28'-7" 28'-7" 28'-7"
37.5 29'-1" 29'-1" 29'-1" 29'-1" 29'-1" 29'-1" 29'-1"
40 29'-11" 29'-6" 29'-6" 29'-6" 29'-6" 29'-6" 29'-6"
42.5 30'-11" 30'-6" 30'-1" 29'-10" 29'-10" 29'-10" 29'-10"
45 31'-11" 31'-6" 30'-8" 30'-8" 30'-3" 30'-3" 30'-5"
47.5 32'-11" 32'-6" 32'-1" 31'-8" 31'-3" 31'-10" 30'-5"
50 33'-10" 33'-5" 33'-0" 32'-7" 32'-2" 31'-9" 31'-4"
52.5 34'-9" 34'-3" 33'-9" 33'-4" 32'-11" 32'-6" 32'-1"
55 35'-7" 35'-1" 34'-7" 34'-2" 33'-8" 33'-3" 32'-10"
57.5 36'-5" 35'-11" 35'-5" 35'-0" 34'-6" 34'-0" 33'-7"
60 37'-3" 36'-9" 36'-3" 35'-9" 35'-3" 34'-9" 34'-4"
62.5 38'-0" 37'-6" 37'-0" 36'-6" 36'-0" 35'-6" 35'-0"
65 38'-9" 38'-2" 37'-8" 37'-2" 36'-8" 36'-2" 35'-8"
67.5 39'-6" 38'-11" 38'-5" 37'-11" 37'-4" 36'-10" 36'-4"
70 40'-3" 39'-8" 39'-2" 38'-7" 38'-1" 37'-6" 37'-0"
72.5 40'-11" 40'-4" 39'-10" 39'-3" 38'-9" 38'-2" 37'-8"
75 41'-8" 41'-1" 40'-7" 40'-0" 39'-5" 38'-10" 38'-4"
77.5 42'-5" 41'-10" 41'-3" 40'-8" 40'-1" 39'-6" 39'-0"
80 43'-1" 42'-6" 41'-11" 41'-4" 40'-9" 40'-2" 39'-7"
82.5 43'-9" 43'-1" 42'-6" 41'-11" 41'-4" 40'-9" 40'-2"
85 44'-6" 43'-10" 43'-3" 42'-7" 42'-0" 41'-4" 40'-9"
87.5 45'-3" 44'-7" 43'-11" 43'-4" 42'-8" 42'-0" 41'-5"
90 46'-0" 45'-4" 44'-8" 44'-0" 43'-4" 42'-8" 42'-0"

* NOTE: All values on this table are for required parking stalls. To determine parking bay widths for
non-required stalls, merely use a column showing a stall width dimension that is 4 inches more.
The values above the darkened lines are governed by minimum aisle width.
The stall widths (8'-6", 8'-10", and 9'-2") are not shown in the ordinance, but are available for
use.

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 6 of 29
 P/ZC 2023-001

TABLE 3: STANDARD CARS - PARKING BAY WIDTHS FOR TWO-WAY TRAFFIC

AND DOUBLE LOADED AISLES, BASED ON CHART NO. 3 IN ORDINANCE NO. 142,306 *
Parking 8'-4" 8'-6" 8'-8" 8'-10" 9'-0" 9'-2" 9'-4"
Angle Stalls Stalls Stalls Stalls Stalls Stalls Stalls
30 51'-2" 51'-2" 51'-2" 51'-2" 51'-2" 51'-2" 51'-2"
32.5 52'-4" 52'-4" 52'-4" 52'-4" 52'-4" 52'-4" 52'-4"
35 53'-3" 53'-3" 53'-3" 53'-3" 53'-3" 53'-3" 53'-3"
37.5 54'-2" 54'-2" 54'-2" 54'-2" 54'-2" 54'-2" 54'-2"
40 54'-10" 54'-10" 54'-10" 54'-10" 54'-10" 54'-10" 54'-10"
42.5 55'-7" 55'-7" 55'-7" 55'-7" 55'-7" 55'-7" 55'-7"
45 56'-4" 56'-4" 56'-4" 56'-4" 56'-4" 56'-4" 56'-4"
47.5 57'-0" 57'-0" 57'-0" 57'-0" 57'-0" 57'-0" 57'-0"
50 57'-8" 57'-8" 57'-7" 57'-7" 57'-0" 57'-6" 57'-6"
52.5 58'-4" 58'-3" 58'-2" 58'-2" 58'-1" 58'-0" 58'-0"
55 58'-11" 58'-9" 58'-8" 58'-7" 58'-6" 58'-5" 58'-4"
57.5 59'-6" 59'-4" 59'-2" 59'-1" 58'-11" 58'-9" 58'-8"
60 59'-11" 59'-9" 59'-7" 59'-5" 59'-3" 59'-1" 58'-11"
62.5 60'-5" 60'-2" 60'-0" 59'-9" 59'-7" 59'-4" 59'-2"
65 60'-11" 60'-8" 60'-5" 60'-2" 59'-11" 59'-8" 58'-5"
67.5 61'-5" 61'-1" 60'-9" 60'-6" 60'-2" 59'-10" 59'-7"
70 61'-10" 61'-5" 61'-1" 60'-9" 60'-5" 60'-1" 59'-9"
72.5 62'-3" 61'-10" 61'-5" 61'-0" 60'-7" 60'-2" 59'-10"
75 62'-7" 62'-1" 61'-8" 61'-3" 60'-9" 60'-4" 59'-11"
77.5 62'-11" 62'-5" 61'-11" 61'-5" 60'-11" 60'-5" 60'-0"
80 63'-3" 62'-8" 62'-2" 61'-7" 61'-1" 60'-6" 60'-0"
82.5 63'-6" 62'-11" 62'-4" 61'-9" 61'-2" 60'-7" 60'-0"
85 63'-9" 63'-1" 62'-6" 61'-10" 61'-3" 60'-7" 60'-0"
87.5 63'-11" 63'-3" 62'-7" 61'-11" 61'-3" 60'-7" 60'-0"
90 64'-0" 63'-4" 62'8" 62'-0" 61'-4" 60'-8" 60'-0"

* NOTE: All values on this table are for required parking stalls. To determine parking bay widths for
non-required stalls, merely use a column showing a stall width dimension that is 4 inches
more. The values above the darkened lines are governed by minimum aisle width.
The stall widths (8'-6", 8'-10", and 9'-2") are not shown in the ordinance, but are available
for use.

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 7 of 29
 P/ZC 2023-001

TABLE 4: STANDARD CARS - PARKING BAY WIDTHS FOR TWO-WAY TRAFFIC AND
SINGLE LOADED AISLES, BASED ON CHART NO. 4 IN ORDINANCE NO. 142,306 *
Parking 8'-4" 8'-6" 8'-8" 8'-10" 9'-0" 9'-2" 9'-4"
Angle Stalls Stalls Stalls Stalls Stalls Stalls Stalls
30 35'-6" 35'-6" 35'-6" 35'-6" 35'-6" 35'-6" 35'-6"
32.5 36'-0" 36'-0" 36'-0" 36'-0" 36'-0" 36'-0" 36'-0"
35 36'-6" 36'-6" 36'-6" 36'-6" 36'-6" 36'-6" 36'-6"
37.5 37'-0" 37'-0" 37'-0" 37'-0" 37'-0" 37'-0" 37'-0"
40 37'-6" 37'-6" 37'-6" 37'-5" 37'-5" 37'-5" 37'-5"
42.5 38'-0" 38'-0" 37'-11" 37'-11" 37'-11" 37'-10" 37'-10"
45 38'-6" 38'-6" 38'-5" 38'-5" 38'-4" 38'-4" 38'-3"
47.5 39'-0" 38'-11" 38'-10" 38'-10" 38'-9" 38'-8" 38'-8"
50 39'-5" 39'-4" 39'-3" 39'-3" 39'-2" 39'-1" 39'-0"
52.5 39'-10" 39'-9" 39'-8" 39'-7" 39'-6" 39'-5" 39'-4"
55 40'-3" 40'-1" 40'-0" 39'-11" 39'-10" 39'-9" 39'-8"
57.5 40'-8" 40'-6" 40'-5" 40'-4" 40'-2" 40'-1" 40'-0"
60 41'-1" 40'-11" 40'-10" 40'-8" 40'-7" 40'-5" 40'-4"
62.5 41'-6" 41'-4" 41'-2" 41'-0" 40'-10" 40'-8" 40'-7"
65 41'-11" 41'-8" 41'-6" 41'-4" 41'-2" 41'-0" 40'-10"
67.5 42'-4" 42'-1" 41'-11" 41'-8" 41'-6" 41'-3" 41'-1"
70 42'-9" 42'-6" 42'-3" 42'-0" 41'-9" 41'-6" 41'-4"
72.5 43'-2" 42'-10" 42'-7" 42'-4" 42'-0" 41'-9" 41'-6"
75 43'-7" 43'-3" 42'-11" 42'-7" 42'-3" 41'-11" 41'-8"
77.5 44'-0" 43'-7" 43'-3" 42'-11" 42'-6" 42'-2" 41'-10"
80 44'-5" 44'-0" 43'-7" 43'-2" 42'-9" 42'-4" 41'-11"
82.5 44'-10" 44'-4" 43'-10" 43'-5" 42'-11" 42'-5" 42'-0"
85 45'-3" 44'-8" 44'-2" 43'-7" 43'-1" 42'-6" 42'-0"
87.5 45'-8" 45'-0" 44'-5" 43'-10" 43'-2" 42'-7" 42'-0"
90 46'-0" 45'-4" 44'-8" 44'-0" 43'-4" 42'-8" 42'-0"

* NOTE: All values on this table are for required parking stalls. To determine parking bay widths for
non-required stalls, merely use a column showing a stall width dimension that is 4 inches more.
The values above the darkened lines are governed by minimum aisle width.
The stall widths (8'-6", 8'-10", and 9'-2") are not shown in the ordinance, but are available for
use.

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 8 of 29
 P/ZC 2023-001

TABLE 5A: PARKING BAY DIMENSIONS FOR COMPACT CARS - REQUIRED STALLS

REQUIRED STALLS
ONE WAY TRAFFIC TWO WAY TRAFFIC
DOUBLE SINGLE DOUBLE SINGLE
ANGLE LOADED LOADED ANGLE LOADED LOADED
α BAY BAY α BAY BAY
WIDTH WIDTH WIDTH WIDTH
30 40'-0" 26'-0" 30 48'-2" 34'-0"
32.5 40'-11" 26'-6" 32.5 49'-1" 34'-5"
35 41'-10" 26'-10" 35 49'-10" 34'-9"
37.5 42'-7" 27'-3" 37.5 50'-6" 35'-2"
40 43'-2" 27'-7" 40 50'-11" 35'-6"
42.5 43'-7" 27'-10" 42.5 51'-6" 35'-10"
45 44'-4" 28'-2" 45 52'-1" 36'-3"
47.5 45'-5" 29'-0" 47.5 52'-7" 36'-6"
50 46'-5" 29'-10" 50 52'-11" 36'-10"
52.5 47'-3" 30'-6" 52.5 53'-4" 37'-2"
55 48'-10" 31'-3" 55 53'-7" 37'-4"
57.5 48'-7" 31'-11" 57.5 53'-10" 37'-8"
60 49'-4" 32'-8" 60 54'-1" 37'-11"
62.5 50'-0" 33'-4" 62.5 54'-3" 38'-2"
65 50'-9" 33'-11" 65 54'-6" 38'-5"
67.5 51'-3" 34'-7" 67.5 54'-8" 38'-9"
70 51'-10" 35'-3" 70 54'-9" 38'-11"
72.5 52'-4" 35'-10" 72.5 54'-10" 39'-2"
75 52'-10" 36'-6" 75 54'-11" 39'-4"
77.5 53'-4" 37'-3" 77.5 55'-1" 39'-7"
80 53'-11" 37'-10" 80 55'-2" 39'-10"
82.5 54'-4" 38'-4" 82.5 55'-3" 39'-11"
85 54'-8" 39'-0" 85 55'-3" 40'-1"
87.5 55'-0" 39'-8" 87.5 55'-3" 40'-2"
90 55'-4" 40'-4" 90 55'-4" 40'-4"

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 9 of 29
 P/ZC 2023-001

TABLE 5B: PARKING BAY DIMENSIONS FOR COMPACT CARS - NON-REQUIRED STALLS

NON-REQUIRED STALLS
ONE WAY TRAFFIC TWO WAY TRAFFIC
DOUBLE SINGLE DOUBLE SINGLE
ANGLE LOADED LOADED ANGLE LOADED LOADED
α BAY BAY α BAY BAY
WIDTH WIDTH WIDTH WIDTH
30 40'-0" 26'-0" 30 48'-2" 34'-0"
32.5 40'-11" 26'-6" 32.5 49'-1" 34'-5"
35 41'-10" 26'-10“ 35 49'-10" 34'-9"
37.5 42'-7" 27'-3" 37.5 50'-6" 35'-2"
40 43'-2" 27'-7" 40 51'-0" 35'-6"
42.5 43'-7" 27'-10" 42.5 51'-6" 35'-10"
45 44'-2" 28'-1" 45 52'-1" 36'-2"
47.5 44'-7" 28'-3" 47.5 52'-7" 36'-5"
50 45'-6" 29'-0" 50 52'-11" 36'-8"
52.5 46'-3" 29'-10" 52.5 53'-2" 37'-0"
55 47'-0" 30'-5" 55 53'-5" 37'-3"
57.5 47'-8" 31'-1" 57.5 53'-7" 37'-6"
60 48'-5" 31'-9" 60 53'-9" 37'-8"
62.5 49'-1" 32'-4" 62.5 53'-10" 37'-11"
65 49'-9" 32'-11" 65 54'-0" 38'-1"
67.5 50'-3" 33'-7" 67.5 54'-0" 38'-4"
70 50'-10" 34'-2" 70 54'-0" 38'-6"
72.5 51'-4" 34'-10" 72.5 54'-0" 38'-8"
75 51'-10" 35'-5" 75 54'-0" 38'-9"
77.5 52'-4" 36'-1" 77.5 54'-0" 38'-11"
80 52'-9" 36'-8" 80 54'-0" 39'-0"
82.5 53'-2" 37'-2" 82.5 54'-0" 39'-0"
85 53'-6" 37'-9" 85 54'-0" 39'-0"
87.5 53'-9" 38'-5" 87.5 54'-0" 39'-2"
90 54'-0" 39'-0" 90 54'-0" 39'-2"

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 10 of 29
 P/ZC 2023-001

TABLE 6: ACCESS AISLE WIDTH FOR 90 DEGREE COMPACT AND STANDARD STALLS

STANDARD STALLS- STANDARD STALLS-ALL COMPACT STALLS

RESIDENTIAL OTHERS
STALL WIDTH AISLE WIDTH STALL WIDTH AISLE WIDTH STALL WIDTH AISLE WIDTH
8'-6" 27'-4" 8'-4" 28'-0" 7'-6" 25'-4"
8'-8" 26'-8" 8'-8" 26'-8" 7'-10" 24'-0"
9'-0" 25'-4" 9'-0" 25'-4" 8'-2" 22'-8"
9'-4" 24'-0" 9'-4" 24'-0" 8'-4" 22'-0"
9'-6" 23'4" 9'-6" 23'-4" 8'-6" 21'-4"
9'-8" 22'-8" 9'-8" 22'-8" 8'-8" 20'-8"
9'-10" 22'-0" 9'-10" 22'-0" 8'-10" 20'-0"

L. CALCULATION OF PARKING SPACES

To determine the number of parking spaces possible on a given sized lot or to determine the
lot size required for a certain number of spaces, refer to Figure 3 and the following procedures:

1. To find the required Length (L) for a certain Number (N) of parking stalls:

a. Select Bay Width (B) from lot area that is available.

b. Using the parking bay charts or tables choose a trial Parking Angle, α (use
maximum) and Stall Width, W (W is 8'-4" minimum for commercial required and
non-required parking, 8'-6" minimum for residential required and non-required
parking.)

NOTE: See Table 1 thru 4 for standard car stall and Tables 5A, 5B, and 6
for compact car stall bay width dimensions.

c. From Figure 3 calculate the following values:

X = S cos α Y = W/sin α Z = W sin α

Then the Length (L) is the sum of the X, Y, and Z dimensions.

L = X + Z + (N-1) Y, which is (one stall) + (all stalls but one) Y

2. To determine the Number (N) of parking stalls possible for an available parking bay of
Length (L)

Total number of parking spaces, N = L - (X + Z) + 1

Y

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 11 of 29
 P/ZC 2023-001

3. For multiple parking bays where the bays overlap and interlock, the net bay widths may
be determined by the parking bay relationships shown below:

a. Parking lot width for overlapping, interlocking bay widths, M (See Figure 3).

b. Compute parking bay overlap width, Q = W cos α then determine required

parking area width as follows:

i. For 2 interlocking bays, both double loaded: lot width = 2B - Q, where

b = width of single loaded bay

ii. For double and single loaded lot width = B + b + Q

iii. For multiple bays, all double loaded: lot width = r (B - Q) + Q, where
r = number of bays

iv. One single loaded end bay: lot width = r (B - Q) - b

both end bays single loaded: lot width = r (B - Q) + b

4. Supplementary dimensions:

a. For angle α, parking stall depth, P = S sin α + Q

b. Driveway aisle width, D

double loaded bays, D = B - 2P
single loaded bays, D = b - P

5. Double loaded means parking on both sides of the driveway access aisle. Single loaded
means parking on one side of the driveway access aisle.

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 12 of 29
 P/ZC 2023-001

M. STRIPING FOR ALL PARKING STALLS OTHER THAN THOSE SERVING A ONE FAMILY
DWELLING

FIGURE 1

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 13 of 29
 P/ZC 2023-001

N. END STALL CONDITIONS

1. For end parking stalls placed at angles greater than 80 degrees, an increase of 3 ft. for
standard stalls and 2 ft. for compact stalls to the Basic Stall Width (BSW) is required.

2. If access aisle extends a minimum of 3 ft. for standard stalls and 2 ft. for compact stalls
beyond the end parking stall, no increase in stall width is required other than the 10 inch
increase for obstructions. (See Figure 2 below)

3. The increase in stall width for end stall conditions or the extension of the access aisle
beyond the end parking stall may be omitted if a minimum of 32 ft. wide access aisle is
provided.

4. For standard stall with access aisle widths between 28 ft. and 32 ft., you can decrease the
3 ft. increase in stall width or extension of the access aisle by 6 ½ inches per foot of width
of access aisle width beyond 28 ft.

5. For compact stalls, you can decrease the 2 ft. increase in stall width or extension of access
aisle by 3 ½ inches per foot of width beyond 28 ft. of access aisle width.

BSW plus 3' for

Std. Car or 2' for
Comp. Car.

BSW: Basic stall width

FIGURE 2

As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its programs, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
Page 14 of 29
 P/ZC 2023-001

_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to this
new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of information
to the public.
15 of 29
 P/ZC 2023-001

O. PARKING WALL HEIGHT

FIGURE 4
1
Wall cannot exceed the height limitation as specified in 12.22C20(f) for “A” or “R” zones.
2
Minimum height for parking wall is measured from the finished grade of the parking surface.

_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to this
new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of information
to the public.
16 of 29
 P/ZC 2023-001

P. DRIVEWAY AND TURNING AREAS

FIGURE 5 - FOR PARALLEL PARKING

FIGURE 6 - CIRCULATION DRIVEWAYS FOR VARIOUS PARKING ANGLES

_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to this
new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of information
to the public.
17 of 29
 P/ZC 2023-001

FIGURE 7 - CIRCULATION DRIVEWAYS

90o Turn
(No Scale)
19' Min. Case II
10' Min. Case I

21' Min. Case II

12' Min. Case I
This area shall be
clear of obstructions
10'-0"

12' Min. Case I

21' Min. Case II
21'-7"
27'-8"

10'-0"

21'-7"

27'-8" 10' Min. Case I

19' Min. Case II

Case I - One-way traffic or two-way traffic where no more than 25 cars go around the turn.

Case II - Two-way traffic and more than 25 cars go around the turn.

_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
18 of 29
 P/ZC 2023-001
FIGURE 8 -MINIMUM ACCESS AISLE PER TABLES 1 THROUGH 6

FIGURE 9 - MINIMUM ACCESS AISLE OF 28'-0" REQUIRED

APARTMENTS AND CONDOMINIUM UNITS ONLY

_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
19 of 29
 P/ZC 2023-001

16' opening

8' - 0"

10'-0"
This area shall
be clear of
obstructions

26' - 8"

FIGURE 10: RESIDENTIAL GARAGE - TURNING CLEARANCE (FOR SINGLE FAMILY WELLINGS)

_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide
reasonable accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to
this new format of code related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of
information to the public.
20 of 29
 P/ZC 2023-001

_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide reasonable
accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to this new format of code
related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of information to the public.
21 of 29
 P/ZC 2023-001

S=20% max.

12-½% max.
½-S ½-S
12-½% max.

8'-0" min. 8'-0" min.

Transition Ramp Transition

Note:
Where ramp intersects the public way, the transition shall be designed
as required by the Department of Public Works.

FIGURE 11B: DRIVEWAY TRANSITIONS (SIMPLIFIED DIAGRAM)

_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide reasonable
accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to this new format of code
related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of information to the public.
22 of 29
 P/ZC 2023-001

Q. MECHANICAL AUTOMOBILE PARKING LIFTS

Mechanical automobile parking lifts can be used to provide required parking spaces with the
following conditions:

Types of mechanical automobile parking lifts that are covered by this section are:
a. 2- post lifts
b. Scissor lifts
c. 4-post lifts

Other types of mechanical automobile parking lift system may be considered on case-
by-case bases. See Figure 12 below for graphical representation of the typical lifts.

FIGURE 12- TYPES OF MECHANICAL AUTOMOBILE PARKING LIFTS

1. ZONING CODE REQUIREMENTS:

A. The platform of the mechanical lift on which the automobile is first places shall be
individually and easily accessible and shall be placed so that the location of the platform
and vehicular access to the platform meets the LAMC Section 12.21A5(a), (b), and (i)
requirements.

B. Electrical Testing Laboratory approval i s required for a m echanical automobile parking

lifts. All of the conditions of approval shall be complied with.

_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide reasonable
accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to this new format of code
related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of information to the public.
23 of 29
 P/ZC 2023-001
C. Mechanical automobile parking lifts must maintain the following clear width between
vertical supports or any obstructions:
a. Minimum 8’- 0” clear width for standard stalls
b. Minimum 7’- 0” clear width for compact stalls.
See Figure 13 below for additional information.

FIGURE 13- MINIMUM CLEAR WIDTH BETWEEN SUPPORTS AND OBSTRUCTIONS

_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide reasonable
accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to this new format of code
related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of information to the public.
24 of 29
 P/ZC 2023-001

D. The stall heights within the mechanical automobile parking lifts shall be as follows:
a. Minimum clear height of 7’-0” for standard stalls
b. Minimum clear height of 6’-0” for compact stalls
See Figure 14 below for additional requirements.

* Minimum required clearance shall be 18” for sprinklers, or as-needed for roll-up doors.
P = Platform thickness (See Manufacturer’s Specifications)
H = Height of any combination of the car type in stacked + P + Ceiling Clearance = Minimum
clear floor to ceiling height required.
FIGURE 14- MINIMUM CLEAR HEIGHTS

_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide reasonable
accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to this new format of code
related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of information to the public.
25 of 29
 P/ZC 2023-001

E. Mechanical automobile parking lifts must provide adequate door clearance for an
attendant to exit a vehicle per manufactures specifications. See Figure 12 and Figure
15 for additional information.

* Obstructions are not allowed within this area

FIGURE 15- VEHICLE DOOR CLEARANCES

F. Mechanical automobile parking lifts shall be arranged in such a manner as to allow full
operation of the sprinkler system. The required ceiling height may be reduced by up to
18 inches if the mechanical automobile parking lift is installed in a non-sprinklered
garage, or when approval has been obtained from the Mechanical Plan Check for wall
mounted Fire sprinklers prior to Building Plan Check approval. Additional headroom
may be required to accommodate installation of roll-up garage doors.

G. Mechanical automobile parking lifts are considered tandem parking. Therefore, they shall
not be installed where tandem parking is prohibited, such as within a commercial corner
lot development, mini-shopping center, for recreational vehicles or guest parking.

H. In a private garage or private parking area, the tandem parking shall not be more than
two-cars in depth [LAMC Section 12.21 A.5 (h)(2)]. Therefore, no parking spaces are
permitted at the front and/or back of mechanical automobile parking lifts.

I. A “Covenant and Agreement to Provide Parking Attendant” shall be recorded with LA

County Recorder’s Office for tandem parking in public parking areas.

J. When tandem parking is provided, parking area shall be capable of accommodating

required onsite queuing spaces for the shuffling of cars. The queuing spaces shall be
arranged so to that the required driveway access aisle is not reduce to less than 10’
wide. Each of the queuing spaces shall be minimum 8’ wide and 18’ long.

K. A “Covenant and Agreement Regarding Maintenance of Vehicle Lift System” shall be

recorded with LA County Recorder’s Office to maintain vehicle lift system in operable
_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide reasonable
accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to this new format of code
related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of information to the public.
26 of 29
 P/ZC 2023-001
conditions at all times. Affidavit# 43A for a 2- level lifts and Affidavit# 43B for 3-level lifts.
The copies of the forms can be obtained from www.LADBS.org.

L. Installation of the mechanical automobile parking lift shall comply with the applicable
provisions of the Los Angeles City Codes (Building, Electrical, Mechanical, Plumbing,
and Fire Codes).

M. Mechanical automobile parking lift shall comply with Los Angeles Fire Department
(LAFD), Fire Prevention Bureau and Public Safety Requirement No. 74. Refer to LAFD
for additional information.

N. Separate permit and approvals shall be obtained for the mechanical and electrical work.

O. The mechanical automobile parking lift shall be installed on a level surface. The
supporting structure and connections to the supporting structure shall be designed by
the State of California licensed civil or structural engineer. The weight of the
automobiles shall be included in determining the design seismic load.

P. Mechanical Automobile parking lifts are not permitted within required front, side, or rear
yards.

2. FIRE DEPARTMENT REQUIREMENTS

A. Mechanical automobile parking lift shall comply with Los Angeles Fire Department
(LAFD), Fire Prevention Bureau and Public Safety Requirement No. 74. Refer to LAFD
for additional information.

3. RECORDING OF AFFIDAVITS

A. A “Covenant and Agreement to Provide Parking Attendant” shall be recorded with LA

County Recorder’s Office for tandem parking in public parking areas.

B. A “Covenant and Agreement Regarding Maintenance of Vehicle Lift System” shall be

recorded with LA County Recorder’s Office to maintain the vehicle lift system in operable
conditions at all times. Affidavit# 43A for a 2- level lifts and Affidavit# 43B for 3-level lifts.
The copies of the forms can be obtained from WWW.LADBS.ORG.

4. MATERIAL AND FABRICATION REQUIREMENTS

A. Structural Steel Materials: Material tests or reports of tests made by a City of Los
Angeles approved fabricator or test laboratory shall constitute sufficient evidence of
conformity with one of the ASTM standards listed in Section A.3 1a of the ANSI/AISC360-
16. For hot-rolled structural shapes, plates, such tests shall be made in accordance with

_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide reasonable
accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to this new format of code
related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of information to the public.
27 of 29
 P/ZC 2023-001
ASTM A568/A568M; for tubing and pipe, such tests shall be made in accordance with the
requirements of the applicable ASTM standards listed above for those product forms.

ASTM Designations: Structural steel material conforming to one of the following ASTM
specifications is approved for use under this Specification:
Hot-rolled structural shapes:
ASTM A36/A36M
ASTM A529/A529M
ASTM A572/A572M
ASTM A588/A588M
ASTM A709/A709M
ASTM A913/A913M
ASTM A992/A992M
ASTM A1043/A1043M
Hollow structural sections (HSS):
ASTM A53/A53M Grade B
ASTM A500/A500M
ASTM A501/A501M
ASTM A618/A618M
ASTM A847/A847M
ASTM A1065/A1065M
ASTM A1085/A1085M
Plates:
ASTM A36/A36M
ASTM A242/A242M
ASTM A283/A283M
ASTM A514/A514M
ASTM A529/A529M
ASTM A572/A572M
ASTM A588/A588M
ASTM A709/A709M
ASTM A1043/A1043M
ASTM A1066/A1066M
Bars:
ASTM A36/A36M
ASTM A529/A529M
ASTM A572/A572M
ASTM A709/A709M
Sheets:
ASTM A606/A606M
ASTM A1011/A1011M SS, HSLAS, and HSLAS-F
_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide reasonable
accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to this new format of code
related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of information to the public.
28 of 29
 P/ZC 2023-001

B. Steel shall be fabricated by a City of Los Angeles Approved Fabricator. See the link
below for the list of the City of Los Angeles approved fabricators
https://www.ladbsservices2.lacity.org/MATCRoster

5. STRUCTURAL DESIGN REQUIREMENTS

A. 2-Post Lifts and Scissor Lifts are considered as equipment. The supporting structures and
connections to the supporting structures shall be designed by the State of California
licensed civil or structural engineer in accordance with the 2023 Los Angeles Building
Code. The weight of the automobiles shall be included in determining the seismic design
load.

B. 4-Post Lifts, where posts and beams are built to support the platforms/equipment, are
considered as structures. A complete design of the structures, supporting structures, and
connections (both gravity and lateral loads) shall be performed by the State of California
licensed civil or structural engineer in accordance with the 2023 Los Angeles Building
Code.

C. Plans and calculations of the structures, supporting structures, and connections shall be
submitted to the plan check section at the time of permit application. The plans and
calculations shall be stamped and signed by a Civil or Structural Engineer registered in
California.

6. ADDITIONAL REQUIREMENTS

A. Electrical Testing Laboratory approval is required for mechanical automobile parking lifts.
All of the conditions of approval shall be complied with.

B. Installation of the mechanical automobile parking lift shall comply with the applicable
provisions of the Los Angeles City Codes (Building, Electrical, Mechanical, Plumbing, and
Fire Codes).

C. Separate permits and approvals shall be obtained for the mechanical and electrical work.

D. The mechanical automobile parking lift shall be installed on a level surface.

_________________________________________________________________________________________
As a covered entity under Title II of the Americans with Disabilities Act, the City of Los Angeles does not discriminate on the basis of disability and, upon request, will provide reasonable
accommodation to ensure equal access to its program, services and activities. For efficient handling of information internally and in the internet, conversion to this new format of code
related and administrative information bulletins including MGD and RGA that were previously issued will allow flexibility and timely distribution of information to the public.
29 of 29