AVSN M7

Set - 3

(@vsn_&tar_Boy)

1) Lightening holes are cut in rib section buscloge frame and other structurel parts.

A.. To decrease Weight

B.. to lighting strike protection

C.. Reduce crack on surface

2) wrinkles on wings.

A.. Hard landing

B..lighting strike

C.. Soft landing

3) Flux used for.

A.. present oxidation

B.. Increase Hardness

C.. Increase tensile stress

4) MTCS.

A.. Inspection worn out of pulleys, failead is very difficult

B.. Critical fatigue area checked by a rag piece to snag on broken wire

C.. Kinking of wire cable can be avoided if probability handled or installed

D.. ALL
5) weight and balance is carried out according to.

A.. Type of aircraft

B.. Atmospheric conditions

C.. Accumulation of dirt, grease

6) Why are test or inspection instruments regularly calibrated and certified.

A.. To ensure they will perform within the required limits of operation

B.. To ensure they can handle the range of measurements required of them

C.. To ensure they are being used regularly

7) Who is responsible for ensuring that weight and balance instrumentation is

serviceable before use.

A.. An engineer holding a license in the instrument category

B.. The manufacturer of the equipment

C.. The person responsible for carrying out the weight and balance procedure

8) At which frequency is the calibration of frequently used crimping tools carried out.

A.. Bi-annually

B.. Annually

C.. Every 1000 crimps

9) What drill angle is used to drill titanium.

A.. 130-140 degrees

B.. 105-120 degrees

C.. 90-100 degrees

10) The UK standard of limits and fits is.

A.. BS4500

B.. BS8888

C.. BS308

11) in welding, base metal is Overheated.

A.. Increase in strength

B.. Porous and brittle weld

C.. Increase in corrosion resistance

12) in composite ultrasonic inspection.

A.. Low frequency, high frequency

B.. Low frequency, high frequencyfrequency and pulse Echometer

C.. Pulse Echometer

13) inspection is carried out according to.

A.. Flight hour

B.. Calendar days

C.. Flight hour and Calendar days

14) Size of the hard hammer is specified by.

A.. Weight of head with handle

B.. weight head without handle

C.. Diameter of the head with handle

D.. Diameter of the head without hondle

15) Null field discharger are used for.

A.. Serve turbulences

B.. Lighting strike protection

C.. Heavy landing

16) Out of how many aircraft mfg weight a single aircraft.

A.. 5

B..10

C.. 15

D.. 20 or 25

17) What shall we do when storing Aircraft in Cold weatherweather.

A.. Extension of flaps & spoiler

B.. Window shall be slightly open and water drained

C.. Water should be stored in tanks and should not be drained

18) MTCS.

A. Aircraft must be inspected using flight hours only

B.. Aircraft must be inspected using calendar days only

C.. Aircraft must be inspected using working days only

D.. Aircraft must be inspected using flight hours and calendar days

19) Angle at which drill point is grounded is called.

A.. Body clearence

B.. Lip clearence

C.. Margin clearence

20) Weather radar colors are.

A.. Green, Red, blue

B.. Blue, green, Yellow

C.. Green, Red, Yellow

21) When using a Pacific tensiometer the correct tension is found by.

A.. reading dial, provided the correct riser is used for the cable diameter

B.. comparing reading to chart provided

C.. adding reading to riser number

22) What temperature should the heat gun be set for shrinking heat shrink sleeve.

A.. At the rated temperature

B.. 100°C below rated temperature

C.. 100°C above rated temperature

23) Calibration of aircraft hydrostatic weighing equipment is.

A.. done once a year

B.. carried out every time before an aircraft is weighed and adjusted by operator

C.. not required

24) When drilling light alloy.

A.. lard oil should be used

B.. use the specified lubricant

C.. no lubricant is required

25) Tolerance is the.

A.. the difference between a hole and shaft size

B.. allowable error due to faulty workmanship and tools

C.. difference between worn and new tools

26) Run-out of a rod is measured using.

A.. DTI, surface plate and V-blocks

B.. micrometer and V-blocks

C.. vernier and V-blocks

27) How would you mark a defect on an exhaust system.

A.. Pencil

B.. Chalk

C.. Special zinc/copper tipped marking tool

28) Which of the following is the most appropriate filing technique.

A.. Pressure backwards, relieve pressure forwards.

B.. Even pressure forward and backwards.

C.. Pressure forwards, relieve pressure backwards

29) Stubborn pins in file teeth should be removed by.

A.. tapping file gently on workbench

B.. using file card

C.. pricking out with sharp point

30) When using low tungsten hacksaw blades it is recommended to use.

A.. 60 strokes per minute

B.. 50 stroke per minute

C.. 40 strokes per minute

31) Helicopter use elastomeric bearing.

A.. Ground properly

B.. should not paas through tail position

C.. Follow Maintenance Manual fo inspection

32) MTCS.

A.. Mg is anodic to all and don't use steel wool

B.. Al is anodic to all and don't use steel wool

C.. Mg is cathodic to all and don't use steel wool

D.. Al is cathodic to all and don't use steel wool

33) Datum is.

A.. Horizontal plane where all horizontal dimension are taken

B.. Imaginary Vertical plane where all vertical measurements are taken

C.. Imaginary horizontal plane where all vertical measurements are taken

D.. Imaginary Vertical plane where all horizontal measurements are taken

34) Tight fit has (Allowance=Clearence).

A.. Zero allowance

B.. Slightly positive allowance

C.. Slightly negative allowance

35) Medium face fit has. (Clearence=allowance)

A.. No clearence

B.. Negative clearence

C.. Considerable negative clearence

36) maximum allowable cross weight__empty__weight.

A.. Usable load

B.. Useful load

C.. Pay load

37) Bismith and cadmium are added to.

A.. Lower the melting point

B.. Increase the melting point

C.. Don't effect the melting point

38) Cable grades.

A. Fairlead

B.. Pully

C.. Pressure seals

D.. All

39) corrosion along grain boundaries.

A.. Fretting corrosion

B.. Intergranular corrosion

C.. Galvanic corrosion

40) Unsalvageable, MTCS.

A.. Which one going to reach their certified life

B.. Which have repairable defect

C.. Which data can not be retrieved

D.. Which can return to Airworthiness conditions

41) Units of torque are.

A.. lbs/ft2 and lbs/in2

B.. Lbs and Kg

C.. lbs.ft and lbs.in

42) What should you check before using a set of V blocks.

A.. That both blocks have the same identification stamps

B.. It doesn't matter

C.. The calibration date

43) The thimble of a metric micrometer is divided into.

A.. 50 equal divisions

B.. 40 equal divisions

C.. 25 equal divisions

44) The measuring capacity of a Vernier Caliper is.

A.. the length of the graduated scale less the length of the vernier scale

B.. the length of the graduated scale

C.. the length of the graduated scale plus the width of the nibs

45) Vee-blocks are manufactured.

A.. as single items and may be paired with any other vee-block

B.. in sets of two and identified for use as a set

C.. in sets of three and identified for use as a set

46) The metric micrometer reading shown is.

A.. 13.87 mm

B.. 13.37 mm

C.. 10.337 mm

47) A ketts saw is used because.

A.. it can cut thicker metal than is required by most repair schemes

B.. it is available both pneumatic and electric

C.. its low torque allows single handed use

48) The gears used in a pistol windy are.

A.. gears in a gearbox

B.. gyrator type gears

C.. spur gears

49) Cross cut files.

A.. cut on the backward stroke only

B.. cut in both directions

C.. cut on the forward stroke only

50) What is used to measure the depth of a blend after a corrosion repair.

A.. Dial Test Indicator

B.. Straight edge and slip gauges

C.. Vernier caliper

51) Centre punches are made of.

A.. high carbon steel with the tip hardened and tempered

B.. case hardened mild steel

C.. high carbon steel hardened and tempered

52) What type of flutes should be used in a reamer for cutting titanium.

A.. Spiral flutes

B.. Straight flutes

C.. Tapered flutes

53) The depth micrometer reading shown is.

A.. 0.261 ins

B.. 0.361 ins

C.. 0.336 ins

54) What should be the included angle of a twist drill for soft metals.

A.. 118 degrees

B.. 65 degrees

C.. 90 degrees

55) What should the point angle of a drill be if it is to be used for drilling titanium (drill
size below 1/4 inch diameter).

A.. 90° to 105°.

B.. 105 to 120°.

C.. 90°.

56) How are pin punches classified.

A.. By length and diameter of the small end

B.. By overall length and type

C.. By type and diameter of the small end

57) The purpose of a taper tap is to.

A.. produce a fine thread

B.. start a thread

C.. form a tapered thread

58) In a front release connector the pin will be.

A.. released from rear and extracted from the front

B.. released from the front and extracted from the front

C.. released from the front and extracted from the rear

59) a rear release connector, the pin will be.

A.. released from the front and extracted from the rear

B.. released from the rear and extracted from the front

C.. released from the rear and extracted from the rear
60) A wire clamped vertically at one end and horizontally at the other end should have a
bend radius of no less than.

A.. 3 times the diameter of the wire

B.. 5 times the diameter of the wire

C.. 10 times the diameter of the wire

61) Different types of stress on aircraft.

A.. Tension & Compression

B. Bending & Torsion

C. Shear & stress

D.. Tension, Compression, shear, bending & Torsion, whose combineed is called
combination stress

62) Ultrasonic and Eddy current done to identify which corrosion.

A.. Fretting corrosion

B.. intergranular corrosion

C.. Stress corrosion

63) Fairlead, MTCS.

A.. fairlead completely encircles the cable where it passes through holes in bulkhead or
other metal parts

B.. Fairlead are used to guide cable in straight line

C.. fairlead should never defects more than 3"

D.. all are correct

64) Burning and erosion is form of.

A.. Serve turbulences

B.. Lighting strike protection

C.. Heavy landing

65) As per safety and quality purpose which minimum must be included in MOI.

A.. Relevant information related to safetysafety, quality and rules regulations must be
knows

B.. Designated person must coperate with quality auditors

C.. Each person must be encouraged to report/errors

66) The maximum operating temperature for a nickel plated copper or aluminium
connector is.

A.. 260°C

B.. 135°C

C.. 200°C

67) What gauge of pin would a yellow plastic insert/extract tool be used on?.

A.. 16 - 14

B.. 12 - 10

C.. 22 - 18

68) What gauge of pin would a red plastic insert/extract tool be used on.

A.. 12 - 10
B.. 22 - 18

C.. 16 - 14

69) What gauge of pin would a blue plastic insert / extract tool be used on.

A.. 12 - 10

B.. 16 - 14

C.. 22 - 18

70) What cable would you use where temperatures are going to exceed 200°C.

A.. Tinned copper or aluminium

B.. Silver plated copper or aluminium

C.. Nickel plated copper or aluminium

71) How long should a fireproof cable last in a fire?.

A.. 5 minutes

B.. 50 minutes

C.. 15 minutes

72) The insulation resistance for wiring in undercarriage wheel-wells should normally be
not less than.

A.. 10 megohms

B.. 5 megohms

C.. 2 megohms
73) What causes knuckling on older type electrical cables.

A.. Over-temperature soldering

B.. Applying cable ties too tightly

C.. Excessive pull through forces

74) To find a high resistance or open circuit, carry out.

A.. a milli-volt drop test

B.. a continuity check

C.. a bonding check

75) The maximum bonding resistance on an aircraft primary structure should be.

A.. 0.01 ohms

B.. 0.001 ohms

C.. 0.05 ohms

76) When referring to fuses, HRC means.

A.. high rupture capacity

B.. hot running capacity

C.. high running current

77) When wiring an electrical component to a plug, the live wire is coloured.

A.. blue

B.. green and yellow

C.. brown
78) A hole is placed in the lowest point of electrical cable conduit.

A.. to allow for pull-through of the cables

B.. to secure the conduit to a piece of aircraft structure

C.. to allow for drainage of moisture

79) The minimum distance between electrical cable splices is.

A.. 3 feet

B.. 12 inches

C.. 500 mm

80) A fire resistant cable is proof tested by exposure to a standard fire for.

A.. 30 minutes

B.. 5 minutes

C.. 15 minutes

"काम भले ही छोटा हो ले कन नाम खुद का बनना चा हए "

(AVSN_STAR_BOY)

NOT - all set's answer given in YouTube Channel - AVSN STAR ZONE

YouTube/Facebook/Instagram/Website/Telegram/Twitter = avsn star zone

YouTube/Facebook/Instagram/Twitter = asb (avsn star boy / aviatorsunilbhabar)

__________________ALL THE BEST_________________