Scribd
Upload
190 views13 pages

Problem Statement

This document outlines 9 problem statements related to automotive component structural analysis using ANSYS and HyperWorks software. Each problem statement involves creating a mesh for a component, assigning material properties, applying loads and constraints, and performing static, modal, harmonic, transient, fatigue and thermal analyses. Screenshots of the modeling process for each problem statement are to be included in a PowerPoint report.

Uploaded by

Kartik Chauhan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
190 views13 pages

Problem Statement

This document outlines 9 problem statements related to automotive component structural analysis using ANSYS and HyperWorks software. Each problem statement involves creating a mesh for a component, assigning material properties, applying loads and constraints, and performing static, modal, harmonic, transient, fatigue and thermal analyses. Screenshots of the modeling process for each problem statement are to be included in a PowerPoint report.

Uploaded by

Kartik Chauhan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 13

ELEATION’s On-Campus Placement

Process
Problem Statement 1: Exhaust

Create 2D meshing on Exhaust


Assume the material and Thickness
Perform Free-Free run to check the connectivity of the
model
Case 1 : Perform Static Analysis assuming the pressure
load and constraint location
Case 2 : Perform Modal Analysis assuming the range of
frequency and Constraint location
Case 3 : Perform Frequency response (Harmonic
Response) analysis assuming the load and constraint
location
Case 4 : Perform Transient Response analysis assuming
the load and constraint location
Case 5 : Perform Fatigue Analysis

Perform Geometry Editing and Meshing, loading


conditions using ANSYS and HyperWorks Software and
compare the results.

Use Problem_1.igs file


Problem Statement 2: Throttle body

Create 3D (Tetra) meshing on Throttle Body


Assume the material
Perform Free-Free run to check the connectivity of the
model
Case 1 : Perform Static Analysis assuming the Force and
moment load and constraint location
Case 2 : Perform Modal Analysis assuming the range of
frequency and Constraint location
Case 3 : Perform Frequency response (Harmonic
Response) analysis assuming the load and constraint
location
Case 4 : Perform Transient Response analysis assuming
the load and constraint location
Case 5 : Perform Fatigue Analysis

Perform Geometry Editing and Meshing, loading


conditions using ANSYS and HyperWorks Software and
compare the results.

Use Problem_2.igs file


Problem Statement 3 : Break Disc

Create 2D meshing on Brake Disc


Assume the material and Thickness
Case 1 : Perform Static Analysis assuming the pressure and constraint
location
Case 2 : Perform Modal Analysis assuming the range of frequency and
Constraint location
Case 3 : Perform Frequency response (Harmonic Response) analysis
assuming the load and constraint location
Case 4 : Perform Transient Response analysis assuming the load and
constraint location
Case 5 : Perform Fatigue Analysis
Case 6 : Perform Steady-State Thermal Analysis assuming loads and
constraint
Case 7 : Perform Transient Thermal Analysis assuming loads and constraint

Perform Geometry Editing and Meshing, loading conditions using ANSYS


and HyperWorks Software and compare the results.

Use Problem_3.igs file


Problem Statement 4 : Knuckle

Create 3D (Tetra) meshing on Knuckle


Assume the material
Case 1 : Perform Static Analysis assuming the loading due to breaking,
cornering and torque and constraint location
Case 2 : Perform Modal Analysis assuming the range of frequency and
Constraint location
Case 3 : Perform Frequency response (Harmonic Response) analysis
assuming the load and constraint location
Case 4 : Perform Transient Response analysis assuming the load and
constraint location
Case 5 : Perform Fatigue Analysis

Perform Geometry Editing and Meshing, loading conditions using ANSYS


and HyperWorks Software and compare the results.

Use Problem_4.igs file


Problem Statement 5 : Wheel Rim

Create 3D (Tetra) meshing on Wheel Rim


Assume the material
Case 1 : Perform Static Analysis assuming the loading due to breaking,
cornering and torque and constraint location
Case 2 : Perform Modal Analysis assuming the range of frequency and
Constraint location
Case 3 : Perform Frequency response (Harmonic Response) analysis
assuming the load and constraint location
Case 4 : Perform Transient Response analysis assuming the load and
constraint location
Case 5 : Perform Fatigue Analysis
Case 6 : Perform Transient Thermal Analysis assuming the loading
condition and constraints

Perform Geometry Editing and Meshing, loading conditions using ANSYS


and HyperWorks Software and compare the results.

Use Problem_5.igs file


Problem Statement 6 : Roll Cage - Supra

Create 2D meshing on Roll Cage


Assume the material and thickness
Perform Free-Free run to check the connectivity on the Geometry.
Case 1 : Perform Static Analysis assuming the force due to front impact and constraint location
Case 2 : Perform Static Analysis assuming the force due to rear impact and constraint location
Case 3 : Perform Static Analysis assuming the force due to side impact and constraint location
Case 4 : Perform Static Analysis assuming the force due to Roll over impact and constraint location
Case 5 : Perform Static Analysis assuming the force due to front bump and constraint location
Case 6 : Perform Static Analysis assuming the force due to rear bump and constraint location
Case 7 : Perform Modal Analysis assuming the range of frequency and Constraint location
Case 8 : Perform Frequency response (Harmonic Response) analysis assuming the load and constraint location
Case 9 : Perform Transient Frequency Response analysis assuming the load and constraint location
Case 10 : Perform Inertia relief Analysis assuming the load and constraint location
Case 11 : Perform CFD Analysis Using ANSYS Fluent software
Case 12 : Perform Dynamic Analysis Using ANSYS Software for front Crash, Rear Impact and Roll Over

Perform Geometry Editing and Meshing, loading conditions using ANSYS and HyperWorks Software and compare the results.

Use Problem_6.igs file


Problem Statement 7 : Differential

Create 3D (Tetra) meshing on Differential


Assume the material
Case 1 : Perform Static Analysis assuming the loading and constraint
location
Case 2 : Perform Modal Analysis assuming the range of frequency and
Constraint location
Case 3 : Perform Frequency response (Harmonic Response) analysis
assuming the load and constraint location
Case 4 : Perform Transient Response analysis assuming the load and
constraint location
Case 5 : Perform Fatigue Analysis
Case 6 : Perform Non-Linear Contact Analysis

Perform Geometry Editing and Meshing, loading conditions using ANSYS


and HyperWorks Software and compare the results.

Use Problem_7.igs file


Problem Statement 8 : Engine

Create 3D (Tetra) meshing on Engine


Assume the material
Perform Free-Free run to check the connectivity of the model
Case 1 : Perform Static Analysis assuming the Force and moment load and
constraint location
Case 2 : Perform Modal Analysis assuming the range of frequency and Constraint
location
Case 3 : Perform Frequency response (Harmonic Response) analysis assuming the
load and constraint location
Case 4 : Perform Transient Response analysis assuming the load and constraint
location
Case 5 : Perform Response Spectrum Analysis assuming the loads and constraint
location
Case 6 : Perform Fatigue Analysis

Perform Geometry Editing and Meshing, loading conditions using ANSYS and
HyperWorks Software and compare the results.

Use Problem_8.igs file


Problem Statement 9 : Roll Cage - BAJA

Create 2D meshing on Roll Cage


Assume the material and thickness
Perform Free-Free run to check the connectivity on the Geometry.
Case 1 : Perform Static Analysis assuming the force due to front impact and constraint location
Case 2 : Perform Static Analysis assuming the force due to rear impact and constraint location
Case 3 : Perform Static Analysis assuming the force due to side impact and constraint location
Case 4 : Perform Static Analysis assuming the force due to Roll over impact and constraint location
Case 5 : Perform Static Analysis assuming the force due to front bump and constraint location
Case 6 : Perform Static Analysis assuming the force due to rear bump and constraint location
Case 7 : Perform Modal Analysis assuming the range of frequency and Constraint location
Case 8 : Perform Frequency response (Harmonic Response) analysis assuming the load and constraint location
Case 9 : Perform Transient Frequency Response analysis assuming the load and constraint location
Case 10 : Perform Inertia relief Analysis assuming the load and constraint location
Case 11 : Perform CFD Analysis Using ANSYS Fluent software
Case 12 : Perform Dynamic Analysis Using ANSYS Software for front Crash, Rear Impact and Roll Over
Case 13 : Create 1D line Geometry from this model, perform 1D Meshing, Apply the same loading condition as in case
1 and compare the results of 1D and 2D meshing
Perform Geometry Editing and Meshing, loading conditions using ANSYS and HyperWorks Software and compare the
results.
Use Problem_9.igs file
Instructions to create the solution report

 Open PowerPoint Presentation(PPT)


 On Slide 1 Enter your Name, Email ID, Mobile Number, College Name
 On Slide 2, copy and paste the problem statement 1
 On Slide 3, copy and paste the Case 1 – then explain the loading values and other assumptions considered by you for
the analysis.
 On Slide 4, paste the full screen screenshot of Geometry opened in ANSYS Software full screen screenshot should
contain date and time of your laptop / desktop
 On Slide 5, paste the full screen screenshot of Material opened in ANSYS Software full screen screenshot should
contain date and time of your laptop / desktop
 On Slide 6, paste the full screen screenshot of Meshing opened in ANSYS Software full screen screenshot should
contain date and time of your laptop / desktop
 On Slide 7, paste the full screen screenshot of Loading Conditions opened in ANSYS Software full screen screenshot
should contain date and time of your laptop / desktop
 On Slide 8, paste the full screen screenshot of Results opened in ANSYS Software full screen screenshot should
contain date and time of your laptop / desktop – If there are more than 1 Results then paste the full screen
screenshot of 2nd results on next slide and so on.
 On Slide 9, paste the full screen screenshot of Geometry opened in HyperWorks Software full screen screenshot
should contain date and time of your laptop / desktop
 On Slide 10, paste the full screen screenshot of Material opened in HyperWorks Software full screen screenshot
should contain date and time of your laptop / desktop
 On Slide 11, paste the full screen screenshot of Meshing opened in HyperWorks Software full screen screenshot
should contain date and time of your laptop / desktop
 On Slide 12, paste the full screen screenshot of Loading Conditions opened in HyperWorks Software full screen
screenshot should contain date and time of your laptop / desktop
 On Slide 13, paste the full screen screenshot of Results opened in HyperWorks Software full screen screenshot should
contain date and time of your laptop / desktop – If there are more than 1 Results then paste the full screen screenshot
of 2nd results on next slide and so on.
 On Slide 14, paste the case 2 of 1st problem statement – then explain the loading values and other assumptions
considered by you for the analysis.
 Follow the same process as explained above for case 2 and so on
 Then follow the same process for problem statement 2 and so on
 Save the PPT in PDF containing the screenshots of all 9 problem statements and all cases.
 Send the PDF to [email protected] on or before 30th June 2023.

You might also like