Scribd
Upload
107 views1 page

PG-GL Data Sheet

This document provides information on the Patriot PG-GL gasket material. It has excellent torque retention and is suitable for use with water, oil, gases, fuels and organic and inorganic acids with good steam and thermal resistance. It has a typical thickness of 2.0 mm, compressibility of 10%, recovery of 55%, and relaxation stress of 29 N/mm2 at 300C and 34 N/mm2 at 175C. Its maximum operating conditions are 400C peak temperature, 340C continuous temperature, and 250C continuous temperature with steam at a pressure of 120 bar. It is available in various standard and custom sizes and thicknesses.

Uploaded by

azeem bilal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
107 views1 page

PG-GL Data Sheet

This document provides information on the Patriot PG-GL gasket material. It has excellent torque retention and is suitable for use with water, oil, gases, fuels and organic and inorganic acids with good steam and thermal resistance. It has a typical thickness of 2.0 mm, compressibility of 10%, recovery of 55%, and relaxation stress of 29 N/mm2 at 300C and 34 N/mm2 at 175C. Its maximum operating conditions are 400C peak temperature, 340C continuous temperature, and 250C continuous temperature with steam at a pressure of 120 bar. It is available in various standard and custom sizes and thicknesses.

Uploaded by

azeem bilal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Company Certified

ISO 9001:2008
TECHNICAL DATA SHEET - CST 01020/02 - 16/01/2018

PATRIOT PG-GL
BASIS
Glass fibers, NBR.

GENERAL PROPERTIES AND APPLICATION


Gasket material with excellent torque retention and good steam and
thermal resistance. Suitable for use with water, oil, gasses, fuels, organic
and inorganic acid.

PG-GL
Typical value thickness 2.0 mm
Compressibility ASTM F36 % 10
Recovery ASTM F36 % 55
Relaxation stress DIN 52913
16 hours, 300°C, 50 N/mm2 N/mm2 29
16 hours, 175°C, 50 N/mm2 34
Tensile strength DIN 52910 N/mm2 8
Thickness increase ASTM F146
1) Oil IRM 903, 5h, 150°C % 6
2) ASTM Fuel B, 5h, 23°C % 6
3) Distilled water, 5h, 100°C % 2
Max operating conditions
Peak Temperature °C / °F 400
Continuous Temperature °C / °F 340
Continuous Temperature with Steam °C / °F 250
Pressure Bar / psi 120
Available sizes : (mm) 1.500 x 1.500 and 1.500 x 3.000; (inch) 60” x 60” and 60” x 120”
Available thickness: (mm) 0,50 ÷ 0,80 ÷ 1,0 ÷ 1,5 ÷ 2,0 ÷ 2,5 ÷ 3,0 ÷ 4,00 ÷ 5,00;
(inch)1/64” ÷ 1/32” ÷ 3/64” ÷ 1/16” ÷ 3/32” ÷ 3/32” ÷ 1/8” ÷ 3/16” ÷ 7/32”;
other thickness available on demand.

Temperature and pressure represent maximum values and should not be used simultaneously. They are given only for guidance, since they depend not only on the
type of gasket material but also on the assembly conditions. Very important factors are: thickness of material, nature of service medium, type of flange, surface
stress. Steam application requires special consideration.

You might also like