Scribd
Upload
152 views

Installation Guide Resler Interface

The document provides installation instructions for connecting a Resler USB interface to allow an Android radio or smartphone to access vehicle data through the I-BUS. There are several connection options for the interface's power, ground, and I-BUS wires, including directly to the vehicle's radio plug, wiring harness, MID connector, or onboard monitor connector. Proper electrical connections are emphasized for safety and to avoid damage. The interface must also be plugged into the radio's USB port to complete the connection.

Uploaded by

ilie eliah
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
152 views

Installation Guide Resler Interface

The document provides installation instructions for connecting a Resler USB interface to allow an Android radio or smartphone to access vehicle data through the I-BUS. There are several connection options for the interface's power, ground, and I-BUS wires, including directly to the vehicle's radio plug, wiring harness, MID connector, or onboard monitor connector. Proper electrical connections are emphasized for safety and to avoid damage. The interface must also be plugged into the radio's USB port to complete the connection.

Uploaded by

ilie eliah
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

The E39 forum and the author assume no liability for these instructions!

Work on - and in the car - is at your own risk...

Improperly executed work can have a negative effect on safety-relevant functions of the car
and the safety of the passengers.

Improper work on the electrical / electronic equipment can lead to further problems
and may end up with malfunctions of your car.

Installation instructions Resler USB interface v2.4

Inhalt
1. Why do we need a Resler USB interface? ..............................................................................................2
2. Connection to the original radio plug ....................................................................................................3
3. Mounting on the adapter wiring harness ..............................................................................................6
4. Connection to the MID connector .........................................................................................................8
5. Connection to the blue connector of the on-board monitor .................................................................9
6. Further connection options ....................................................................................................................9
7. Do not forget the USB port! ...................................................................................................................9

2018 >blue_racer< www.e39-forum.de Seite |1


Let's start with the basic question:

1. Why do we need a Resler USB interface?

The interface serves as an interface to the vehicle K / I-BUS. If you have a BMW E39 and an Android
navigation radio, such as the Xtrons PB7839BAP (or an Android smartphone with a USB interface) and a
suitable app (e.g. the BMW I-BUS App), you can access the vehicle BUS, read and write vehicle data from
the bus and use the BC functions with Android radios.
For connection, we have a couple of options due to the "single line BUS" design.
Basically, the USB interface needs three wire connections: +12 V, Ground, I/K-Bus [white]
The fourth, green wire is not needed, simply ignore that wire.

!!!Important!!!

The connections must never be swapped or reversed,


otherwise the interface will be destroyed.

Be sure to use a secure, reliable electrical connection.


We advise to refrain from so-called "wire-tap connectors".
The best way to connect the wires are "butt" or "solder connectors" or
solder the wire directly with appropriate isolation.

The following examples show different connection options.


We always favor the connection directly on the radio plug!

2018 >blue_racer< www.e39-forum.de Seite |2


Connection to the Adapter-Radio cable

2. Connection to the original radio plug


The ideal connection is the adapter cable that comes with the radio.
The interface can be soldered directly on the radio connections.
The cable colors on the adapter cable are 12 V -> yellow, ground -> black and I / K-BUS -> green.
Connections New Generation: Block A : PIN 9: I/K-Bus, PIN 12: Ground, PIN 15: 12V

Anschlüsse Old Generation: PIN 7: I/K-Bus, PIN 15: Masse, PIN 9: 12V

The installation is illustrated by an NG Quadlock plug.

2018 >blue_racer< www.e39-forum.de Seite |3


Unpin the desired PIN in the adapter cable from the front, e.g. with a needle or similar tool.
IMPORTANT: remember the correct position!

This nose has to be pushed back and slightly bent back to the original shape after unpinning.

Solder and insulate the associated wire directly on the pin.

2018 >blue_racer< www.e39-forum.de Seite |4


Put the Pin back in the plug.
Repeat with the other two strands.
Isolate the unused green wire at the free end only.

Ideally, the four loose strands are fixed every few inches with insulating tape to avoid knotting.
That's it.
It's ready to go back into the car now.

2018 >blue_racer< www.e39-forum.de Seite |5


3. Mounting on the adapter wiring harness
Supplement of User „Desert Fox“
The plug to be disconnected is actually a socket.
You recognize it because it has only four strands.
Please DO NOT disconnect the main plug with 17 wires!

Radio Adapterkabel, hier Stecker leeres Y-Ende Resler Interface


Block / PIN Funktion Kabelfarbe Funktion Kabelfarbe
A/9 I/K-Bus green K-Bus white
A / 12 Ground (Terminal. 31) Black Ground Brown
A / 15 12 V (Terminal 30, Yellow 12V (Terminal. 30) red
Permanent+)
A / 16 Ignition – not used Red
NTSC (not used) green

Radio adapter cable with cut off plug of the unnecessary Y-end.
The cable colors refer to the block / pin of the radio adapter

Cable of the cut off connector with labels for connection to the Resler interface.

2018 >blue_racer< www.e39-forum.de Seite |6


Connection to the Resler interface

2018 >blue_racer< www.e39-forum.de Seite |7


4. Connection to the MID connector

If a MID was installed previously, the easiest way to connect the interface is on this plug because it is no
longer needed.
To accomplish this, the wires are best connected and fixed with suitable pin contacts.

Part-Number of a single Pin: 61131383672


PIN 1: Ground: Brown -> Brown-Black
PIN 2: 12V: Red -> Red-Black
PIN 4: I/K-Bus: White -> White-Grey-Yellow(dotted)

2018 >blue_racer< www.e39-forum.de Seite |8


5. Connection to the blue connector of the on-board monitor
Another option is to connect the interface to the blue connector (X18801) of the on-board monitor.
The relevant cable colors are:
12 V -> red-green,
ground -> brown and
I / K-BUS -> white-gray-yellow.

6. Further connection options


In addition, the interface can also be connected anywhere where the I-bus is applied, e.g. to LCM, PDC,
CD changer.
However, keep in mind that the interface has to be connected to the USB port of the radio as well.

Good luck with the installation. 

7. Do not forget the USB port!

An important, although absolutely logical point:


Of course, the USB-Resler interface must also be plugged into a USB socket of the radio (or smartphone
/ tablet)
Please do not use any USB extension cables and or USB-hubs between the radio USB Port and the
interface.
So, BOTH connections (the loose wires to the vehicle) as well as the USB
connection to the Android device are absolutely necessary!

2018 >blue_racer< www.e39-forum.de Seite |9

You might also like