0% found this document useful (0 votes)

19 views

PLC Connection Guide

Uploaded by

Виталий Дядечкин

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

19 views

PLC Connection Guide

Uploaded by

Виталий Дядечкин

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 755

PLC Connection Guide

PLC Connection Guid

Altus ALNET-I ............................................................. 2 HUST H4X ................................................................ 137
BACnet BACnet/IP ...................................................... 6 IAI X-SEL CONTROLLER .................................... 139
Barcode (USB/COM) ................................................. 17 IDEC Micro .............................................................. 142
Baumuller ................................................................... 19 Inovance H2U/H1U .................................................. 146
Beckhoff ADS/AMS (Ethernet) ................................. 22 Justfi Controller ....................................................... 149
Beckhoff Embedded PC ............................................. 29 Kernel sistemi DMX Series ...................................... 151
CANopen Slave (for eMT3000 only) ......................... 36 KEYENCE KV-10/16/24/40/80/Visual KV Series.. 153
Change......................................................................... 39 KEYENCE KV-5000 (Ethernet) ............................. 156
Cimon CM1-CP4A/ECO1A ...................................... 41 KEYENCE KV-700/1000/3000/5000 Series............ 158
Cimon CM1-SC02A ................................................... 43 Korenix 6550 ............................................................. 160
Copley Controls .......................................................... 45 KOYO CLICK.......................................................... 162
CROUZET M3 (FBD)................................................ 49 KOYO DIRECT ....................................................... 165
CROUZET M3 (LAD) ............................................... 52 KOYO Ethernet........................................................ 177
Danfoss ECL Apex20 ................................................. 55 Lenze.......................................................................... 179
Danfoss ECL Apex20 (Ethernet)............................... 58 LingYan BMS ........................................................... 181
Danfoss FC Series ....................................................... 60 LIYAN EX series ...................................................... 183
Danfoss VLT2800 Series ............................................ 62 LoXin ......................................................................... 185
DELTA DVP ............................................................... 64 LS GLOFA Cnet ....................................................... 187
DL/T645 CHUANG HONG....................................... 66 LS GLOFA FEnet (Ethernet) .................................. 192
DL/T645 Standard ..................................................... 74 LS GLOFA GM3467 (LOADER) ........................... 194
DL-BCM Server ......................................................... 76 LS MASTER-K Cnet ............................................... 196
EMERSON Charge Module ...................................... 79 LS MASTER-K CPU Direct .................................... 198
EMERSON PLC EC20 .............................................. 81 LS MASTER-K MODBUS RTU ............................. 200
FATEK FB Series ....................................................... 83 LS MASTER-K10S1 ................................................ 202
Fuji NB Series ............................................................. 90 LS XGB Cnet ............................................................ 204
GE FANUC 0i MD ..................................................... 93 LS XGB FEnet (Ethernet) ....................................... 207
GE Fanuc CMM ......................................................... 96 LS XGI Cnet ............................................................. 210
GE FANUC RX3i ..................................................... 101 LS XGI CPU DIRECT ............................................. 214
GE Fanuc Series 90-30 (Ethernet) .......................... 105 LS XGI FEnet (Ethernet) ........................................ 217
GE Fanuc SNP-X...................................................... 108 LS XGK Cnet ............................................................ 219
Haiwell PLC.............................................................. 113 LS XGK FEnet (Ethernet) ....................................... 223
Hanyoung Controller ............................................... 116 LS XGT/XGK CPU DIRECT ................................. 226
HAWE PLVC ........................................................... 119 LS Mecapion Metronix AnyPack ............................ 229
Heng Yuan EU series ............................................... 121 Master-Slave Server ................................................. 231
Hitachi EH-SIO ........................................................ 123 Memory Map ............................................................ 234
Hitachi EH-SIO ........................................................ 123 MIKOM MX Series PLC ......................................... 239
Hitachi EHV Series (Ethernet)................................ 128 Mitsubishi A1S.......................................................... 242
Hitachi H/EH/EHV Series ....................................... 130 Mitsubishi A2A/A2U/A2AS/A2USH ....................... 245

1
PLC Connection Guide
Mitsubishi A2N/A3A/A3N/A1SH/A2SH ................. 248 OMRON FINS (Ethernet) ....................................... 408
Mitsubishi A2US....................................................... 251 OMRON Host Link .................................................. 410
Mitsubishi AJ71 ........................................................ 254 Panasonic FP............................................................. 414
Mitsubishi AJ71 (AnA/AnU CPU) .......................... 258 Panasonic FP (Ethernet) .......................................... 422
Mitsubishi AJ71 (Format 4) .................................... 262 Panasonic FP2 (Ethernet) ........................................ 425
Mitsubishi F930GOT Server ................................... 266 Panasonic MINAS A4 .............................................. 427
Mitsubishi FX0s/FX0n/FX1s/FX1n/FX2 ................ 269 Panasonic MINAS A5 .............................................. 433
Mitsubishi FX232/485BD ......................................... 273 Parker ACR9000 ...................................................... 437
Mitsubishi FX2n ....................................................... 278 Parker Compax3 ...................................................... 439
Mitsubishi FX3u (Ethernet) .................................... 281 Parker Compumotor 6K Series ............................... 444
Mitsubishi FX3u/FX3G............................................ 288 Parker SLVD Series ................................................. 446
Mitsubishi MELSEC-Q/L (Ethernet) ..................... 291 Rockwell CompactLogix - Free Tag Names ........... 449
Mitsubishi MR J3 A ................................................. 295 Rockwell CompactLogix/FlexLogix ........................ 451
Mitsubishi MR-MQ100 (Ethernet) ......................... 302 Rockwell DF1 ............................................................ 455
Mitsubishi Q00/Q00UJ/Q01/QJ71 .......................... 305 Rockwell DF1 (BCC) ................................................ 459
Mitsubishi Q00J ....................................................... 314 Rockwell DH485 ....................................................... 463
Mitsubishi Q00U/Q01U/Q02U/QnUD/QnUDH ..... 316 Rockwell EtherNet/IP (CompactLogix) .................. 468
Mitsubishi Q00UJ/QnU/QnUD/QnUDH/QnUDEH Rockwell EtherNet/IP (CompactLogix) – Free Tag
(mini USB) ................................................................ 319 Names ........................................................................ 471
Mitsubishi Q02/02H ................................................. 321 Rockwell EtherNet/IP (ControlLogix) – Free Tag
Mitsubishi Q06H ...................................................... 324 Names ........................................................................ 475
Mitsubishi QJ71E71 (Ethernet) .............................. 327 Rockwell EtherNet/IP (DF1) ................................... 480
MODBUS ASCII ...................................................... 334 Rockwell PLC5 ......................................................... 483
MODBUS ASCII Server .......................................... 339 RS Automation OEMAX Series .............................. 487
MODBUS RTU ......................................................... 343 SAIA PCD PGU Mode ............................................. 489
MODBUS RTU (0x/1x Range Adjustable) ............. 348 SAIA PCD S-BUS Mode .......................................... 491
MODBUS RTU (Adjustable)................................... 357 SAIA S-BUS (Ethernet) ........................................... 499
MODBUS RTU (zero-based addressing)................ 364 Samsung SPC-10 ...................................................... 502
MODBUS Server (COM/Ethernet) ........................ 369 SCENE6 Controller.................................................. 504
MODBUS TCP/IP .................................................... 377 Schleicher XCS 20C ................................................. 506
MODBUS TCP/IP (0x/1x Range Adjustable) ........ 379 Schleicher XCX 300 ................................................. 509
MODBUS TCP/IP (zero-based addressing) ........... 385 Schneider MODBUS RTU ....................................... 514
MODBUS TCP/IP 32Bit .......................................... 387 Schneider MODBUS TCP/IP .................................. 518
Moeller XC-CPU101 ................................................ 389 Schneider UniTelway ............................................... 520
OHJX ........................................................................ 391 SEW Movilink .......................................................... 522
OMRON C/CQM1 Series ........................................ 394 SEW MOVITRAC LTE .......................................... 524
OMRON CJ/CS/CP ................................................. 398 SHIMADEN MR13/FP93 ........................................ 528
OMRON CJ1/CS1 (Ethernet) ................................. 402 SHJ-A ........................................................................ 540
OMRON E5CN/E5EZ/E5ZN .................................. 404 SICK FLEXI SOFT ................................................. 542

2
PLC Connection Guide
Siemens LOGO (Ethernet) ...................................... 544 Trio MODBUS RTU, TCP/IP (Mode 7) ................. 659
Siemens S7-1200 (Ethernet)..................................... 549 VIGOR ...................................................................... 664
Siemens S7-200 ......................................................... 555 VIPA 200 ................................................................... 668
Siemens S7-200 (Ethernet)....................................... 558 VIPA 200 (VD any address) .................................... 671
Siemens S7-200 (VD any address) ........................... 565 VIPA 200, for ex. 214-2BT10 (Ethernet) ................ 674
Siemens S7-200 PPI .................................................. 568 VIPA 300 ................................................................... 676
Siemens S7-300 ......................................................... 573 VIPA 300 MPI .......................................................... 684
Siemens S7-300 MPI ................................................ 581 VIPA 300S (Ethernet) .............................................. 692
Siemens S7-300/ET200S (Ethernet) ........................ 589 VIPA 300S, for ex. 315-4NE12 (Ethernet) .............. 699
Siemens S7-400 (Ethernet)....................................... 595 XINJE XC Series ...................................................... 705
Siemens TI505 .......................................................... 603 YAMAHA ERCD ..................................................... 707
Siemens TI565/C400................................................. 609 YASKAWA CCMEP ............................................... 710
SSTC SSD Series ...................................................... 615 YASKAWA Memobus (MP Series Controllers) .... 712
TECHSOFT Intelligent Servo ................................. 627 YASKAWA MP Series Ethernet (Extension) ........ 719
TECO Inverter ......................................................... 629 YASKAWA MP2300Siec ......................................... 724
TECO TP02 Series ................................................... 632 YASKAWA SMC 3010 ............................................ 733
TECO TP03 Series ................................................... 635 YASKAWA SMC 3010 (Ethernet) .......................... 737
TINHAO ................................................................... 638 YOKOGAWA FA-M3 ............................................. 740
Toptek Topvert ......................................................... 641 YOKOGAWA FA-M3 (Ethernet) ........................... 746
TOSHIBA T Series ................................................... 644 YUDIAN AIBUS ....................................................... 748
TOSHIBA VF-S11 .................................................... 649 MT6050i/MT8050i Com Port Pin Assignment ...... 752
TOSHIBA MACHINE Provisor TC200 ................. 652
Trio MODBUS RTU, TCP/IP ................................. 654

3
PLC Connection Guide

Altus ALNET-I
Supported Series: Altus SeriesMode PO3042, PO3142, PO3242, PO3342, PL103 ,PL104,
PL105, QK800, QK801, QK2000.

HMI Setting:
Parameters Recommended Options Notes
PLC type Altus ALNET-I
PLC I/F RS232
Baud rate 9600
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device Type Format Range Memo
B M_Bit DDDDh 0 ~ 1023f Memories
B A DDDh 0 ~ 511f Auxiliary Relays
B E DDDh 0 ~ 511f Input Relays
B D_Bit DDDDdd 0 ~ 102331 Decimals
B F_Bit DDDDdd 0 ~ 102331 Reals
B I_Bit DDDDdd 0 ~ 102331 Integers
B S DDDh 0 ~ 511f Output Relays
W M DDDD 0 ~ 4096 Memories
DW D DDDD 0 ~ 4096 Decimals
DW F DDDD 0 ~ 1023 Reals
DW I DDDD 0 ~ 1023 Integers
W TM HHHH 0 ~ ffff* Memory Tables
DW TD HHHH 0 ~ ffff* Decimal Tables
DW TF HHHH 0 ~ ffff* Real Tables
DW TI HHHH 0 ~ ffff* Integer Tables

2
PLC Connection Guide
Note: The formats of TM, TD, TF and TI in PLC software are represented as TXA[B]. “X”
can be M, D, F, or I.
The address range of B is 0~FF, and A is 0~FF. The device type is AABB, and the range
depends on the PLC settings.
For example: Model PO3242, range of “A” is ”0” and range of “B” is 0 ~ 7.

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 8P RJ45: PLC PO3042, PO3142, PO3242, PO3342
eMT3000 series
COM1 RS232 9P COM3 RS232 9P PLC RS232 8P RJ45
D-Sub Female D-Sub Female Male
2 RX 8 RX 2 TX
3 TX 7 TX 3 RX
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P PLC RS232 8P RJ45
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 3 RX
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P PLC RS232 8P RJ45
D-Sub Female Male
9 RX 2 TX
6 TX 3 RX
5 GND 5 GND

3
PLC Connection Guide
The following represents the cable end connector.
9P D-Sub to 9P D-Sub: PLC PL103, PL104, PL105
eMT3000 series
COM1 RS232 9P COM3 RS232 9P PLC RS232 9P D-Sub
D-Sub Female D-Sub Female Male
2 RX 8 RX 7 TX
3 TX 7 TX 1 RX
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P PLC RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 7 TX
3 TX 4 TX 7 TX 1 RX
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P PLC RS232 9P D-Sub
D-Sub Female Male
9 RX 7 TX
6 TX 1 RX
5 GND 5 GND

4
PLC Connection Guide
The following represents the cable end connector.
9P D-Sub to 9P D-Sub: PLC QK800, QK801, QK2000.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P PLC RS232 9P D-Sub
D-Sub Female D-Sub Female Male
2 RX 8 RX 2 TX
3 TX 7 TX 3 RX
5 GND 5 GND 7 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P PLC RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 3 RX
5 GND 5 GND 5 GND 7 GND

MT6050i/MT8050i
COM1 RS232 9P PLC RS232 9P D-Sub
D-Sub Female Male
9 RX 2 TX
6 TX 3 RX
5 GND 7 GND

Driver Version:
Version Date Description
V1.10 Jul/24/2009

5
PLC Connection Guide

BACnet BACnet/IP

Supported series: BACnet/IP protocol devices

HMI Setting:
Parameters Recommended Options Notes
PLC type BACnet/IP
PLC I/F Ethernet
Port no. 47808
HMI port no. 47808 47808~47823
Device ID 342566 0~999999 According to device.
PLC sta. no. 1

BACnet/IP to MS/TP Adapter Setting:

1. When using BACnet/IP driver, check “Use [BACnet/IP to MS/TP Adapter]” to enable
this type of communication.

2. As shown above, in BACnet/IP to MS/TP Adapter mode, [Network number] must follow
the factory setting, and enter the device station number in [Device ID].

3. [HMI port no]. default: 47808, can be filled in other effective value.

6
PLC Connection Guide

How to Import Tags:

EasyBuilder Pro provides two ways to gain tag addresses. One is to directly get tag
information via internet, another is to export the generated CSV file via SCADA, and then
import to EasyBuilder Pro. The following introduces how to import tag address information.

Step 1. Add BACnet/IP driver in System Parameters Settings

Step 2. Correctly set the relevant parameters.

7
PLC Connection Guide
Step 3. Get tag address information

Way 1: Click Get Tag Info.

Way 2: Import the CSV file generated by SCADA software.

8
PLC Connection Guide
CSV file content is shown below; users can build the file and import:
a. Object format
b. OBJECT NAME (user defined tag name, EasyBuilder will start reading data from the
6th row of CSV file.), DEVICE ID, OBJECT TYPE(object ID) and INSTANCE(object
address)

Step 4. File imported successfully.

Take (10，2)File as an example, 10 represents object ID, 2 represents object address, File
represents user defined name or default name.

9
PLC Connection Guide

Default Object Model:

Object ID Object Name Object Structure
0 Analog Input Object Name
Object Identifier
Object Type
Present Value
Event State
Out Of Service
Units
Min Press Value
Max Press Value
Cov Increment
Resolution
High Limit
Low Limit
Dead Band
Profile Name
1 Analog Output Object Name
Object Identifier
Object Type
Present Value
Event State
Out Of Service
Units
Relinquish Default
Min Press Value
Max Press Value
Cov Increment
Resolution
High Limit
Low Limit
Dead Band
Profile Name
2 Analog Value Object Name
Object Identifier
Object Type
Present Value
Event State

10
PLC Connection Guide
Object ID Object Name Object Structure
Out Of Service
Units
Relinquish Default
Cov Increment
High Limit
Low Limit
Dead Band
Profile Name
3 Binary Input Object Name
Object Identifier
Object Type
Present Value
Event State
Out Of Service
Polarity
Profile Name
Notify Type
Alarm Value
4 Binary Output Object Name
Object Identifier
Object Type
Present Value
Event State
Out Of Service
Polarity
Profile Name
Notify Type
5 Binary Value Object Name
Object Identifier
Object Type
Present Value
Event State
Out Of Service
Profile Name
Notify Type
Alarm Value
6 Calendar Object Name
Object Identifier

11
PLC Connection Guide
Object ID Object Name Object Structure
Object Type
Present Value
7 Command Object Name
Object Identifier
Object Type
Present Value
In Process
All Writes Successful
8 Device Object Name
Object Identifier
Object Type
System Status
Vendor Name
Vendor Identifier
Model Name
Firmware Revision
Application Software Version
Protocol Version
Protocol Revision
Max APDU length Accepted
Segmentation Supported
Apdu Timeout
Number Of APDU retries
Data Base Revision
Max Segments Accepted
Day light Savings Status
Apdu Segment Timeout
Backup Failure Timeout
10 File Object Name
Object Identifier
Object Type
File Type
File Size
Archive
Read Only
11 Group Object Name
Object Identifier
Object Type

12
PLC Connection Guide
Object ID Object Name Object Structure
13 Multi State Object Name
Input Object Identifier
Object Type
Present Value
Event State
Out Of Service
Reliability
Number Of States
Time Delay
Notification Class
Notify Type
Profile Name
14 Multi State Object Name
Output Object Identifier
Object Type
Present Value
Event State
Out Of Service
Reliability
Number Of States
Time Delay
Notification Class
Notify Type
Profile Name
15 Notification Object Name
Class Object Identifier
Object Type
Notification Class
Priority
17 Schedule Object Name
Object Identifier
Object Type
Present Value
Priority For Writing
Reliability
Out Of Service
18 Averaging Object Name
Object Identifier

13
PLC Connection Guide
Object ID Object Name Object Structure
Object Type
Minimum Value
Average Value
Maximum Value
Attempted Samples
Valid Samples
Window Interval
Window Samples
19 Multi State Object Name
Value Object Identifier
Object Type
Present Value
Event State
Out Of Service
Reliability
Number Of States
Notification Class
Notify Type
Profile Name
Time Delay
20 Trend Log Object Name
Object Identifier
Object Type
Enable
Stop When Full
Buffer Size
Record Count
Total Record Count
21 Life Safety Object Name
Point Object Identifier
Object Type
Present Value
Tracking Value
Event State
Reliability
Out Of Service
Mode
Silenced

14
PLC Connection Guide
Object ID Object Name Object Structure
22 Life Safety Object Name
Zone Object Identifier
Object Type
Present Value
Tracking Value
Event State
Reliability
Out of Service
Mode
Silenced
23 Accumulator Object Name
Object Identifier
Object Type
Present Value
Event State
Out Of Service
Scale
Units
Reliability
24 Pulse Object Name
Converter Object Identifier
Object Type
Present Value
Event State
Out Of Service
Units
Scale Factor
Adjust Value
High Limit
Low Limit
Dead Band
Cov Increment
Count
Note 1. Object name can not include “#”.

15
PLC Connection Guide

Wiring Diagram:
Direct connect (crossover cable):
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 3 RX+
2 TX- Orange 6 RX-
3 RX+ White/Green 1 TX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 2 TX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Through a hub:
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 1 TX+
2 TX- Orange 2 TX-
3 RX+ White/Green 3 RX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 6 RX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Driver Version:
Version Date Description
V1.00 Jan/12/2012 Driver released

16
PLC Connection Guide

Barcode (USB/COM)

HMI Setting:
Parameters Recommended Options Notes
PLC type Barcode (USB/COM)
PLC I/F RS232 RS232/485,USB
Baud rate 9600 9600~115200
Data bits 8 7,8
Parity None None, Even, Odd
Stop bits 1 1,2
CR/LF, STX/ETX,
Terminator CR/LF
Other, None

Device Address:
Bit/Word Device type Format Range Memo
B FLAG DD 0 flag
W Barcode 0 DD 0 length
W Barcode 1 DD 1~255 string

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female FeMale
2 RX 8 RX TXD
3 TX 7 TX RXD
5 GND 5 GND GND

17
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male FeMale
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub
D-Sub Female FeMale
9 RX TXD
6 TX RXD
5 GND GND

Driver Version:
Version Date Description
V1.30 Oct/1/2010

18
PLC Connection Guide

Baumuller
Website: http://www.baumuller.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Baumuller
PLC I/F RS485 4W
Baud rate 19200 9600, 19200
Data bits 8 7 or 8
Parity Even Even, Odd, None
Stop bits 1 1 or 2
HMI sta. no. 0
PLC sta. no. 0 Defaults

PLC Setting:
Communication mode RK 512 Protocol, 19200, 8, 1, Even

Device Address:
Bit/Word Device type Format Range Memo
DB0_bit ~
B DDDh 0 ~ 255f
DB29_bit
W DB0 ~ DB29 DDD 0 ~ 255

19
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 4W Baumuller servo RS422
9P D-Sub Male 9P D-Sub Male
1 RX- 1 TXD-
2 RX+ 9 TXD+
3 TX- 5 RXD-
4 TX+ 6 RXD+
5 GND 8 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W Baumuller servo RS422
9P D-Sub Male 9P D-Sub Male
1 RX- 1 TXD-
2 RX+ 9 TXD+
3 TX- 5 RXD-
4 TX+ 6 RXD+
5 GND 8 GND

MT6050i/MT8050i
COM1 RS485 4W Baumuller servo RS422
9P D-Sub Female 9P D-Sub Male
1 RX- 1 TXD-
2 RX+ 9 TXD+
3 TX- 5 RXD-
4 TX+ 6 RXD+
5 GND 8 GND

20
PLC Connection Guide

Driver Version:
Version Date Description
V1.10 Apr/17/2009

21
PLC Connection Guide

Beckhoff ADS/AMS (Ethernet)

Supported Series: Twincat

HMI Setting:
Parameters Recommended Options Notes
PLC type Beckhoff ADS/AMS (Ethernet)
PLC I/F Ethernet
Port no. 48898
ADS port 801 801, 811, 821, 831
PLC sta. no. 1

PLC Setting:
Step1.
Open TwinCat System Properties.

PLC Settings: Set HMI Name, AMS Net ID, and Address.
Ex:
HMI IP: 192.168.1.15
AMS Net ID: Must input 192.168.1.15.1.1
Address: 192.168.1.15
Name: Input “HMI” or any user–defined name.

22
PLC Connection Guide
Step2.
Simulate PLC on PC. 2 Twincat drivers must be installed as follows:

23
PLC Connection Guide

Step3.
The following commands can be utilized for Twincat PLC to output the parameters
observed.

24
PLC Connection Guide
PS. Twincat PLC
IX, QX, MX - Must output in BOOL type.
IW, QW, MW - Must output in UINT, WORD, and INT types.
ID, QD, MD - Must output in UDINT, DWORD, and DINT types.

Project -> Rebuild all

Step4. Set PLC IP in EasyBuilder.

25
PLC Connection Guide
Step5.
Click [Import Tag] button in EasyBuilder to open the TPY file compiled by Twincat PLC
Control.

Step6.
Download the project compiled in EasyBuilder to HMI.

26
PLC Connection Guide

Device address:
Bit/Word Device type Format Range Memo
B IX DDDDDo 0 ~ 655357 o : Bit no.(0 ~ 7)
B QX DDDDDo 0 ~ 655357 o : Bit no.(0 ~ 7)
B MX DDDDDo 0 ~ 655357 o : Bit no.(0 ~ 7)
W IW DDDDD 0 ~ 65535
W QW DDDDD 0 ~ 65535
W MW DDDDD 0 ~ 65535
DW ID DDDDD 0 ~ 65535
DW QD DDDDD 0 ~ 65535
DW MD DDDDD 0 ~ 65535

27
PLC Connection Guide
Through a hub:
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 1 TX+
2 TX- Orange 2 TX-
3 RX+ White/Green 3 RX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 6 RX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Driver Version:
Version Date Description
V1.00 Dec/08/2010 Driver released.
V1.10 Aug/24/2011 Extended address range up to 65535.

28
PLC Connection Guide

Beckhoff Embedded PC

Supported Series: Intel-CX10x0,CX50x0 and Twincat

HMI Setting:
Parameters Recommended Options Notes
PLC type Beckhoff Embedded PC
PLC I/F Ethernet
Port no. 48898
ADS port 801 801, 811, 821, 831
PLC sta. no. 1

PLC Setting:
For Twincat:
a. Confirm PC IP address

29
PLC Connection Guide
b. Open Twincat, Set IP address 169.254.56.12.1.1

c. Use Twincat to build a Route Table to make sure the system is connected, if PLC
power turns OFF and then ON, please redo this step.
Note: when connected, if “X” is displayed, the connection succeeded.

30
PLC Connection Guide
d. Open EasyBuilder, set IP address, ADS port and Port no.

e. Run on line simulation.

Note: If the project is downloaded to HMI, please set HMI IP 169.254.56.12 identically
to Twincat IP address setting.

For CERHOST:
a. Execute CERHOST.exe to connect with PLC on PC.

b. Enter PLC IP and Password (default password: 1).

31
PLC Connection Guide
c. Succeeded to connect with PLC, click Start -> click Control Panel.

d. Click [Network and Dial-Up Connections] to display PLC device information; select
the PLC to check its IP.

e. Access PLC system settings, the default directory: \Hard Disk\System, execute
[TcAmsRemoteMgr].

32
PLC Connection Guide
f. AMS Net Id consists of 6 numbers, separated by “.”. The first 4 numbers stand for IP
and followed by “1.1”. The figure below shows the AMS Net Id of Local Computer,
please enter PLC IP plus “1.1”. Remote Computers shows the information of the HMI
to connect with. Click [Add] to add the HMI and click [OK] to finish setting.

g. Name: Device name.

AMS Net Id: The IP followed by “1.1” of the device to connect with.
Address: The IP address of the device to connect with.
Transport: The way of connection.
Slow Connection: As shown in the figure below.

33
PLC Connection Guide
h. Return to Control Panel; execute CX Configuration Tool to confirm PLC AMS Net
Id.

i. Confirm settings and click Start -> Reset PLC.

Driver Version:
Version Date Description
V1.00 Apr/18/2011 Driver released.
V1.10 Aug/24/2011 Extended address range up to 65535.

35
PLC Connection Guide

CANopen Slave (for eMT3000 only)

eMT3000 series only

HMI Setting:
Parameters Recommended Options Notes
PLC type CAN (Controller Area Network) Bus
Node ID 1 1~127
Baud rate 250K 10K~1M
Follow the steps to import EDS file.

Step 1. Object Dictionary Settings -> Setting

Step 2. Import EDS file.

36
PLC Connection Guide
Step 3. Select the EDS file to be imported.

Step 4. Successfully import EDS file.

Device Address:
Bit/Word Device type Format Range Memo
B TxPDOn_BIT DDDDo 100 ~ 99977
B RxPDOn_BIT DDDDo 100 ~ 99977
W TxPDOn DDDD 10 ~ 9997
W RxPDOn DDDD 10 ~ 9997
W SDO_8bit HHHHHH 0~FFFFFF
W SDO_16bit HHHHHH 0~FFFFFF
W SDO_32bit HHHHHH 0~FFFFFF

37
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
CAN Bus 9P CAN Device
D-Sub Female
7 D- D-
8 D+ D+
5 GND GND

Demo Project Link:

Driver Version:
Version Date Description
V1.00 Jul/5/2011 Driver released.

38
PLC Connection Guide

Change
Supported Series: Compressor controller

Website: http://www.sh-changjia.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Change
PLC I/F RS485 2W
Baud rate 9600
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 1 1~6

Device Address:
Bit/Word Device type Format Range Memo
B CTL DDD 0 ~ 5, 128, 150 Write only
DW SET DDD 0 ~ 57, 128
DW STATUS DD 1 ~ 20 Read only

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W Change RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 15 D-
2 RX+ 9 Data+ 16 D+
5 GND 5 GND

39
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W Change RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 15 D-
2 RX+ 9 Data+ 16 D+
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W Change RS485 terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- 15 D-
2 RX+ 8 Data+ 16 D+
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Jan/19/2011 Driver released.

40
PLC Connection Guide

Cimon CM1-CP4A/ECO1A
Supported Series: Cimon CM1 series, CP4A module

Website: http://www.kdtsys.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Cimon CM1-CP4A/ECO1A
PLC I/F RS232
Baud rate 38400
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
B X DDh 0 ~ 23f 0-1F Read Only
B Y DDh 0 ~ 23f
B M DDDh 0 ~ 511f
B K DDDh 0 ~ 127f
B L DDDh 0 ~ 127f
B F DDDh 0 ~ 127f Read Only
B T DDDh 0 ~ 102f
B C DDDh 0 ~ 102f
W D DDDD 0 ~ 4999
W S DD 0 ~ 99 Max. Range: 99
W TS DDDD 0 ~ 1023
W TC DDDD 0 ~ 1023
W CS DDDD 0 ~ 1023
W CC DDDD 0 ~ 1023

41
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P CM1-CP4A RS232 6P
D-Sub Female D-Sub Female RJ11 Male
2 RX 8 RX 2 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P CM1-CP4A RS232 6P
D-Sub Female D-Sub Female D-Sub Male RJ11 Male
2 RX 6 RX 8 RX 2 TXD
3 TX 4 TX 7 TX 3 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P CM1-CP4A RS232 6P
D-Sub Female RJ11 Male
9 RX 2 TXD
6 TX 3 RXD
5 GND 5 GND

Driver Version:
Version Date Description
V1.20 Nov/30/2009

42
PLC Connection Guide

Cimon CM1-SC02A
Supported Series: Cimon CM series, SC02A module

Website: http://www.kdtsys.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Cimon CM1-SC02A
PLC I/F RS232
Baud rate 38400
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
B X DDh 0 ~ 23f 0-1F Read Only
B Y DDh 0 ~ 23f 0-F Read Only
B M DDDh 0 ~ 511f
B K DDDh 0 ~ 127f
B L DDDh 0 ~ 127f
B F DDDh 0 ~ 127f Read Only
B T DDDh 0 ~ 102f
B C DDDh 0 ~ 102f
W D DDDD 0 ~ 4999
W S DD 0 ~ 99 Max. Range: 99
W TS DDDD 0 ~ 1023
W TC DDDD 0 ~ 1023
W CS DDDD 0 ~ 1023
W CC DDDD 0 ~ 1023

43
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P CM1-SC02A RS232 9P
D-Sub Female D-Sub Female D-Sub Male
2 RX 8 RX 3 TD
3 TX 7 TX 2 RD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P CM1-SC02A RS232 9P
D-Sub Female D-Sub Female D-Sub Male D-Sub Male
2 RX 6 RX 8 RX 3 TD
3 TX 4 TX 7 TX 2 RD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P CM1-SC02A RS232 9P
D-Sub Female D-Sub Male
9 RX 3 TD
6 TX 2 RD
5 GND 5 GND

Driver Version:
Version Date Description
V1.20 Nov/30/2009

44
PLC Connection Guide

Copley Controls
Supported Series: Digital Servo Driver & Controllers, Xenus, Xenus Micro, Accelnet,
Accelnet Micro, Stepnet series.

Website: http://www.copleycontrols.com/motion/

HMI Setting:
Parameters Recommended Options Notes
PLC type Copley Controls
PLC I/F RS232
Baud rate 9600 9600~115200
Data bits 8 8
Parity None Even, Odd, None
Stop bits 1 1
HMI sta. no. 0
PLC sta. no. 0 0-127

Device Address:
Bit/Word Device type Format Range Memo
W Flash INT 16 HHH 0 ~ 999 For Register is INT16 or U16
W RAM INT 16 HHH 0 ~ 999 For Register is INT16 or U16
W Flash INT 32 HHH 0 ~ 999 For Register is INT32 or U32
W RAM INT 32 HHH 0 ~ 999 For Register is INT32 or U32
W Register DDDD 0 ~ 2457
W T_command H 0
W Reset H 0

45
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 6P RJ11: Xenus, Xenus Micro, Accelnet, Stepnet
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 6P RJ11 Male
D-Sub Female D-Sub Female
2 RX 8 RX 5 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 3, 4 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 6P RJ11 Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 5 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 3, 4 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 6P RJ11 Male
D-Sub Female
9 RX 5 TXD
6 TX 2 RXD
5 GND 3, 4 GND

46
PLC Connection Guide
The following represents the cable end connector.
Accelnet Micro:
eMT3000 series
COM1 RS232 9P COM3 RS232 9P Accelnet Micro Panel
D-Sub Female D-Sub Female RS232 J5 Cable
Connector
2 RX 8 RX 29 TXD
3 TX 7 TX 14 RXD
5 GND 5 GND 15 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P Accelnet Micro Panel
D-Sub Female D-Sub Female D-Sub Male RS232 J5 Cable
Connector
2 RX 6 RX 8 RX 29 TXD
3 TX 4 TX 7 TX 14 RXD
5 GND 5 GND 5 GND 15 GND

47
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P Accelnet Micro Panel
D-Sub Female RS232 J5 Cable
Connector
9 RX 29 TXD
6 TX 14 RXD
5 GND 15 GND

Driver Version:
Version Date Description
V1.20 Dec/30/2008

48
PLC Connection Guide

CROUZET M3 (FBD)

HMI Setting:
Parameters Recommended Options Notes
PLC type CROUZET M3 (FBD)
PLC I/F RS232
Baud rate 115200
Data bits 7
Parity Even
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
B SLI_Bit DDh 10 ~ 24f Serial link input
B SLO_Bit DDh 250 ~ 48f Serial link output (read only)
B State D 1 State in PLC (read only)
W IA DD 1 ~ 99 Analogy input (default: 1 ~ 4)
W SL_IN DD 1 ~ 24 Serial link input
W SL_OUT DD 25 ~ 48 Serial link output (read only)
W Time D 1~6 Time & Day*
W Order D 1 Command** (write only)
* : address 1: second, address 2 : minute, address 3 : hour , address 4 : day, address 5 :
month, address 6 : year. The value range for “Year” is 0~99, entering “0” represents year
2000, entering “99” represents year 2099.
**: run mode write 2, stop mode write 1.

49
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P CROUZET M3 RS232
D-Sub Female 9P D-Sub Male
(Extension Cable)
2 RX 2 TD
3 TX 3 RD
5 GND 5 GND
7 RTS 4 DTR

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P CROUZET M3 RS232
D-Sub Female 9P D-Sub Male
(Extension Cable)
2 RX 2 TD
3 TX 3 RD
5 GND 5 GND
7 RTS 4 DTR

(3m serial link cable)

Note: Please use 3m serial link cable
(Accessories from Millenium 3) and extension
cable (as shown) to communicate with HMI
series.

50
PLC Connection Guide

Driver Version:
Version Date Description
V1.10 Oct/26/2010
V1.20 Mar/29/2012 Add device type : State, Time, Order
V1.30 May/14/2012 “Time” entering is now allowed.

51
PLC Connection Guide

CROUZET M3 (LAD)

HMI Setting:
Parameters Recommended Options Notes
PLC type CROUZET M3 (LAD)
PLC I/F RS232
Baud rate 115200
Data bits 7
Parity Even
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
B I DD 1 ~ 99 Input (default: 1 ~ 4)
B O DD 1 ~ 99 Output (default: 1 ~ 4)
B M DD 1 ~ 28 Relay
B SLI_Bit DDh 10 ~ 24f Serial link input
B SLO_Bit DDh 250 ~ 48f Serial link output (read only)
B State D 1 State in PLC (read only)
W T DD 1 ~ 12 Timer
W C DD 1 ~ 16 Counter
W IA DD 1 ~ 99 Analogy input (default: 1 ~ 4)
W SL_IN DD 1 ~ 24 Serial link input
W SL_OUT DD 25 ~ 48 Serial link output (read only)
W Time D 1~6 Time & Day *
W Order D 1 Command (write only) **
* : address 1: second, address 2 : minute, address 3 : hour , address 4 : day, address 5 :
month, address 6 : year .The value range for “Year” is 0~99, entering “0” represents year
2000, entering “99” represents year 2099.
**: run mode write 2, stop mode write 1.

52
PLC Connection Guide

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P CROUZET M3 RS232
D-Sub Female 9P D-Sub Male
(Extension Cable)
2 RX 2 TD
3 TX 3 RD
5 GND 5 GND
7 RTS 4 DTR

(3m serial link cable)

Note: Please use 3m serial link cable
(Accessories from Millenium 3) and extension
cable (as shown) to communicate with HMI
series.

53
PLC Connection Guide

Driver Version:
Version Date Description
V1.20 Oct/26/2010
V1.30 Mar/30/2012 Add device type : State, Time, Order
V1.40 May/14/2012 “Time” entering is now allowed.

54
PLC Connection Guide

Danfoss ECL Apex20

Website: http://www.danfoss.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Danfoss ECL Apex20
PLC I/F RS232
Baud rate 9600
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
B Flag DDDD 0 ~ 8191
B Output DDDD 0 ~ 1023
B Input DDDD 0 ~ 1023
B Reg_Bit DDDDDdd 0 ~ 1638331 dd: Bit no. (00 ~ 31)
DW Register DDDDD 0 ~ 16383
DW Counter DDDD 0 ~ 1599
DW Timer DDDD 0 ~ 1599
DW Reg_Float DDDDD 0 ~ 16383 Support 32-bit float format
EasyBuilder device address range may differ from PLC extended mode, please refer to
EasyBuilder address range as above.

55
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P ECL Apex20 Controller
D-Sub Female D-Sub Female RS232 9P D-Sub Male
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P ECL Apex20 Controller
D-Sub Female D-Sub Female D-Sub Male RS232 9P D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

MT6050i/MT8050i
COM1 RS232 9P ECL Apex20 Controller
D-Sub Female RS232 9P D-Sub Male
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
7 RTS
circuit
8 CTS

56
PLC Connection Guide
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W ECL Apex20 Controller
9P D-Sub Male 9P D-Sub Male Port#1 / Port#0
1 RX- 6 Data- 11 / 29
2 RX+ 9 Data+ 12 / 28
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W ECL Apex20 Controller
9P D-Sub Male 9P D-Sub Male Port#1 / Port#0
1 RX- 6 Data- 11 / 29
2 RX+ 9 Data+ 12 / 28
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W ECL Apex20 Controller
9P D-Sub Female 9P D-Sub Female Port#1 / Port#0
1 RX- 7 Data- 11 / 29
2 RX+ 8 Data+ 12 / 28
5 GND 5 GND

Driver Version:
Version Date Description
V1.40 OCT/06/2008

57
PLC Connection Guide

Danfoss ECL Apex20 (Ethernet)

Website: http://www.danfoss.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Danfoss ECL Apex20 (Ethernet)
PLC I/F Ethernet
Port no. 5050
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B Flag DDDD 0 ~ 8191
B Output DDDD 0 ~ 1023
B Input DDDD 0 ~ 1023
B Reg_Bit DDDDDdd 0 ~ 1638331 dd: Bit no. (00 ~ 31)
W Register DDDDD 0 ~ 16383
W Counter DDDD 0 ~ 1599
W Timer DDDD 0 ~ 1599
W Reg_Float DDDDD 0 ~ 16383 Support 32-bit float format

EasyBuilder device address range may differ from PLC extended mode, please refer to
EasyBuilder address range as above.

58
PLC Connection Guide

Driver Version:
Version Date Description
V1.10 Jan/10/2011

59
PLC Connection Guide

Danfoss FC Series
Supported Series: FC051, FC100, FC200, FC300, VLT Micro Driver.

Website: http://www.danfoss.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Danfoss FC Series
PLC I/F RS485 2W
Baud rate 9600
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
W Parameter 09 DDDD 0 ~ 9999 Set Parameter
DW Reference 10 D 0~1 Control Bus Reference
DW Para_Index 11 DDDDDD 0 ~ 999999 Set Parameter(Index)
Para_Index 310.1=31001, Para_Index310.0=31000

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W FC RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 69 D-
2 RX+ 9 Data+ 68 D+
5 GND 5 GND

60
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W FC RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 69 D-
2 RX+ 9 Data+ 68 D+
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W FC RS485 terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- 69 D-
2 RX+ 8 Data+ 68 D+
5 GND 5 GND

*RW100 set PCD1 Control Word of station 1

*RW101 read PCD1 Status Word of station 1
*RW102 set PCD2 Control Word of station 2
*RW103 read PCD2 Status Word of station 2
*RW104 set PCD3 Control Word of station 3
*RW105 read PCD3 Status Word of station 3
*RW106 set PCD4 Control Word of station 4
*RW107 read PCD4 Status Word of station 4

Driver Version:
Version Date Description
V1.10 Jan/14/2010

61
PLC Connection Guide

Danfoss VLT2800 Series

Supported Series: VLT2800 series

Website: http://www.danfoss.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Danfoss VLT2800 Series
PLC I/F RS485 2W
Baud rate 9600
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 1 0-126 According to PLC

PLC Setting:
Communication mode 9600, Even, 8, 1 (default)

Device Address:
Bit/Word Device type Format Range Memo
DW Parameter DDDD 0 ~ 2000 Set Parameter
W Reference D 0~1 Control Bus Reference

The control word register is set according to the station number.

If the station number is 1, the control word will be RW100 and RW101; if the station
number is 2, the control word will be RW102 and RW103, and so on.

62
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 69 D-
2 RX+ 9 Data+ 68 D+
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 69 D-
2 RX+ 9 Data+ 68 D+
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- 69 D-
2 RX+ 8 Data+ 68 D+
5 GND 5 GND

Driver Version:
Version Date Description
V1.10 Dec/30/2008

63
PLC Connection Guide

DELTA DVP
Supported Series: DELTA DVP series

Website: http://www.deltadriver.com

HMI Setting:
Parameters Recommended Options Notes
PLC type DELTA DVP
PLC I/F RS232 RS232, RS485
Baud rate 9600 9600, 19200
Data bits 7 7, 8
Parity Even Even, Odd, None
Stop bits 1 1
PLC sta. no. 1 0-255

Device Address:
Bit/Word Device type Format Range Memo
B X OOOOO 0 ~ 23417 (octal) Input
B Y OOOOO 0 ~ 23417 (octal) Output
B M DDDDD 0 ~ 65536 Auxiliary Relay
B S DDDD 0 ~ 9999 Step Relay
B T DDDD 0 ~ 9999 Timer
B C DDDD 0 ~ 9999 Counter
B TV_Bit DDDDdd 0 ~ 999915 Timer
W TV DDDD 0 ~ 9999 Timer
W CV DDD 0 ~ 127 Counter
W CV2 DDD 200 ~ 254 Double Word Counter
W D DDDD 0 ~ 9999 Data Register

64
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 8P Mini-DIN
D-Sub Female D-Sub Female Male
2 RX 8 RX 5 TXD
3 TX 7 TX 4 RXD
5 GND 5 GND 3/8 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 8P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 5 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 3/8 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 8P Mini-DIN
D-Sub Female Male
9 RX 5 TXD
6 TX 4 RXD
5 GND 3/8 GND

Driver Version:
Version Date Description
V1.20 Dec/30/2008

65
PLC Connection Guide

DELTA DVPEN01-SL (Ethernet)

Website: http://www.deltadriver.com

HMI Setting:
Parameters Recommended Options Notes
PLC type DELTA DVPEN01-SL (Ethernet)
PLC I/F Ethernet
Port no. 502
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B C_Bit DDD 0 ~ 255
B M DDDD 0 ~ 4095
B S DDDD 0 ~ 1023
B T_Bit DDD 0 ~ 255
B X OOO 0 ~ 377
B Y OOO 0 ~ 377
W C DDD 0 ~ 255
W D DDDD 0 ~ 9999
W T DDD 0 ~ 255

66
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 Jun/11/2012 Driver released.

67
PLC Connection Guide

DL/T645 CHUANG HONG

Website: http://www.cw180.com

HMI Setting:
Parameters Recommended Options Notes
PLC type DL/T645 CHUANG HONG
PLC I/F RS485 2W
Baud rate 9600
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
W B621 D 0~1
W B622 D 0~1
W B623 D 0~1
W zero phase D 0~1
W B611 D 0~1
W B612 D 0~1
W B613 D 0~1
W B631 D 0~1
W B632 D 0~1
W B633 D 0~1
W B630 D 0~1
W B641 D 0~1
W B642 D 0~1
W B643 D 0~1
W B640 D 0~1
W A-apparentT D 0~1
W B-apparentT D 0~1
W C-apparentT D 0~1
W T-apparentT D 0~1
W B650 D 0~1

68
PLC Connection Guide
Bit/Word Device type Format Range Memo
W B651 D 0~1
W B652 D 0~1
W B653 D 0~1
W 9010 D 0~1
W 9020 D 0~1
W 9110 D 0~1
W 9120 D 0~1
W 9130 D 0~1
W 9140 D 0~1
W 9150 D 0~1
W 9160 D 0~1
W 9410 D 0~1
W 9420 D 0~1
W 9510 D 0~1
W 9520 D 0~1
W 9530 D 0~1
W 9540 D 0~1
W 9550 D 0~1
W 9560 D 0~1
W 9810 D 0~1
W 9820 D 0~1
W 9910 D 0~1
W 9920 D 0~1
W 9930 D 0~1
W 9940 D 0~1
W 9950 D 0~1
W 9960 D 0~1
W A010 D 0~1
W A020 D 0~1
W A110 D 0~1
W A120 D 0~1
W A130 D 0~1
W A140 D 0~1
W A150 D 0~1
W A160 D 0~1
W A410 D 0~1
W A420 D 0~1
W A510 D 0~1
W A520 D 0~1
W A530 D 0~1

69
PLC Connection Guide
Bit/Word Device type Format Range Memo
W A540 D 0~1
W A550 D 0~1
W A560 D 0~1
W A810 D 0~1
W A820 D 0~1
W A910 D 0~1
W A920 D 0~1
W A930 D 0~1
W A940 D 0~1
W A950 D 0~1
W A960 D 0~1
W B010 D 0~1
W B020 D 0~1
W B110 D 0~1
W B120 D 0~1
W B130 D 0~1
W B140 D 0~1
W B150 D 0~1
W B160 D 0~1
W B410 D 0~1
W B420 D 0~1
W B510 D 0~1
W B520 D 0~1
W B530 D 0~1
W B540 D 0~1
W B550 D 0~1
W B560 D 0~1
W B810 D 0~1
W B820 D 0~1
W B910 D 0~1
W B920 D 0~1
W B930 D 0~1
W B940 D 0~1
W B950 D 0~1
W B960 D 0~1
W B210 D 0~1
W B211 D 0~1
W B212 D 0~1
W B213 D 0~1
W B214 D 0~1

70
PLC Connection Guide
Bit/Word Device type Format Range Memo
W B310 D 0~1
W B311 D 0~1
W B312 D 0~1
W B313 D 0~1
W B320 D 0~1
W B321 D 0~1
W B322 D 0~1
W B323 D 0~1
W B330 D 0~1
W B331 D 0~1
W B332 D 0~1
W B333 D 0~1
W B340 D 0~1
W B341 D 0~1
W B342 D 0~1
W B343 D 0~1
W C010 D 0~1
W C011 D 0~1
W C020 D 0~1
W C021 D 0~1
W C022 D 0~1
W C030 D 0~1
W C031 D 0~1
W C032 D 0~1
W C033 D 0~1
W C034 D 0~1
W C111 D 0~1
W C112 D 0~1
W C113 D 0~1
W C114 D 0~1
W C115 D 0~1
W C116 D 0~1
W C117 D 0~1
W C118 D 0~1
W C119 D 0~1
W C11A D 0~1
W C211 D 0~1
W C212 D 0~1
W C310 D 0~1
W C311 D 0~1

71
PLC Connection Guide
Bit/Word Device type Format Range Memo
W C312 D 0~1
W C313 D 0~1
W C314 D 0~1
W C320 D 0~1
W C321 D 0~1
W C322 D 0~1
W C330 D 0~1
W C331 D 0~1
W C332 D 0~1
W C340 D 0~1
W C341 D 0~1
W C342 D 0~1
W C3A0 D 0~1
W C3A1 D 0~1
W C3A2 D 0~1
W C410 D 0~1
W C411 D 0~1
W C41E D 0~1
W C510 D 0~1
W C511 D 0~1
W B634 D 0~1
W B635 D 0~1

72
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 13 RS485B1
2 RX+ 9 Data+ 12 RS485A1
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 13 RS485B1
2 RX+ 9 Data+ 12 RS485A1
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- 13 RS485B1
2 RX+ 8 Data+ 12 RS485A1
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Apr/13/2011 Driver released.

73
PLC Connection Guide

DL/T645 Standard

Website: http://www.cw180.com

HMI Setting:
Parameters Recommended Options Notes
PLC type DL/T645 Standard
PLC I/F RS485 2W
Baud rate 9600
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
W Data HHHHHHHH 0 ~ 6FFFFFF

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND

74
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Apr/14/2011 Driver released.

75
PLC Connection Guide

DL-BCM Server

Website: http://www.hzdelin.com

HMI Setting:
Parameters Recommended Options Notes
PLC type DL-BCM Server
PLC I/F RS232 RS232, RS485
Baud rate 9600 9600~115200
Data bits 8 8
Parity None Even, Odd, None
Stop bits 1 1
PLC sta. no. 0 0-31

Device Address:
Bit/Word Device type Format Range Memo
B LB dddd 0 ~ 9998
W LW dddd 0 ~ 9998
W RW ddddd 0 ~ 55536

76
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male FeMale
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND
RTS
circuit
CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub
D-Sub Female FeMale
9 RX TXD
6 TX RXD
5 GND GND
RTS
circuit
CTS

The following represents the cable end connector.

eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 8 D-
2 RX+ 9 Data+ 3 D+
5 GND 5 GND 5 GND

77
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 8 D-
2 RX+ 9 Data+ 3 D+
5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 8 D-
2 RX+ 8 Data+ 3 D+
5 GND 5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Dec/8/2008 Driver released

78
PLC Connection Guide

EMERSON Charge Module

Website: http://www.emersonnetworkpower.com.cn/Pages/Default.aspx

HMI Setting:
Parameters Recommended Options Notes
PLC type EMERSON Charge Module
PLC I/F RS-232
Baud rate 9600
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
B Float_Point_Forced D 0~1
B Average_Point_Forced D 0~1
W Switch_Status D 0~1
W Manual_Status D 0~1
W Protect_Status D 0~1
W Failure_Status D 0~1
W Preset_Voltage D 0~1
W Preset_Percent D 0~1
W Output_Voltage D 0~1
W Output_Current D 0~1
W High_Limit D 0~1
W Low_Limit D 0~1
W Float_Point_Setting D 0~1
W Average_Point_Setting D 0~1

79
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 terminal
D-Sub Female D-Sub Female
2 RX 8 RX TXD
3 TX 7 TX RXD
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 terminal
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS232 9P RS232 terminal
D-Sub Female
9 RX TXD
6 TX RXD
5 GND GND

Driver Version:
Version Date Description
V1.00 Mar/3/2009

80
PLC Connection Guide

EMERSON PLC EC20

Supported Series: Emerson PLC EC20 Series. (Modbus RTU Protocol)

HMI Setting:
Parameters Recommended Options Notes
PLC type EMERSON PLC EC20
PLC I/F RS232
Baud rate 9600 9600, 19200, 115200
Data bits 8 7 or 8
Parity Even Even, Odd, None
Stop bits 1 1 or 2
PLC sta. no. 0 0-255

PLC Setting:
Communication mode Modbus RTU protocol

Device Address:
Bit/Word Device type Format Range Memo
B Y OOO 0 ~ 377 0000-02550
B X OOO 0 ~ 377 1200-01455 0000-0255
B M DDDD 0 ~ 1999 2000-3999
B SM DDD 0~ 255 4400-4655
B S DDD 0 ~ 991 6000-6991
B T DDD 0 ~ 255 8000-8255
B C DDD 0 ~ 255 9200-9455
W D DDDD 0 ~ 7999 0000-7999
W SD DDD 0 ~ 255 8000-8255
W Z DD 0 ~ 15 8500-8515
W T DDD 0 ~ 255 9000-9255
W C DDD 0 ~ 199 9500-9699
DW C_Double DDD 200 ~ 255 9700-9811
DW D_Double DDDD 0 ~ 7998 0000-7999

81
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P Emerson EC20 COM1
D-Sub Female D-Sub Female terminal
2 RX 8 RX TXD
3 TX 7 TX RXD
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P Emerson EC20 COM1
D-Sub Female D-Sub Female D-Sub Male terminal
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS232 9P Emerson EC20 COM1
D-Sub Female terminal
9 RX TXD
6 TX RXD
5 GND GND

Driver Version:
Version Date Description
V1.10 Dec/30/2008

82
PLC Connection Guide

FATEK FB Series
Supported Series: FATEK FBs series, FB MC series, and FB MA series need FB-DTBR
converter.
Website: http://www.fatek.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type FATEK FB Series
PLC I/F RS232 RS232/RS485
Baud rate 9600 /Ethernet
Data bits 7
Parity Even
Stop bits 1
PLC sta. no. 1 0-255 Must match PLC port setting.
TCP port no. 500 Ethernet only.

Device Address:
Bit/Word Device type Format Range Memo
B X DDDD 0 ~ 9999 Input
B Y DDDD 0 ~ 9999 Output
B M DDDD 0 ~ 9999 Internal Relay
B S DDDD 0 ~ 9999 Step Relay
B T DDDD 0 ~ 9999 Timer
B C DDDD 0 ~ 9999 Counter
B PLC_MODE D 0 PLC mode
B R_Bit DDDDdd 0 ~ 999915
B D_Bit DDDDdd 0 ~ 999915
W RT DDDD 0 ~ 9999 Timer Register
W RC DDDD 0 ~ 9999 Counter Register
W R DDDD 0 ~ 9999 Data Register
W D DDDD 0 ~ 9999 Data Register
W DRT DDDD 0 ~ 9999 Double Word Timer Register
W DRC DDD 200 ~ 255 Double Word Counter Register
W WX DDDD 0 ~ 9999 Input Word
W WY DDDD 0 ~ 9999 Output Word

83
PLC Connection Guide
Bit/Word Device type Format Range Memo
W WM DDDD 0 ~ 9999 Internal Relay Word
W WS DDDD 0 ~ 9999
W FR DDDD 0 ~ 9999

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 4P Mini-DIN: FBs Port0
eMT3000 series
COM1 RS232 9P COM3 RS232 9P FBs RS232 4P Mini-DIN
D-Sub Female D-Sub Female Male
2 RX 8 RX 3 TX
3 TX 7 TX 4 RX
5 GND 5 GND 2 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P FBs RS232 4P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 3 TX
3 TX 4 TX 7 TX 4 RX
5 GND 5 GND 5 GND 2 GND

84
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P FBs RS232 4P Mini-DIN
D-Sub Female Male
9 RX 3 TX
6 TX 4 RX
5 GND 2 GND

The following represents the cable end connector.

9P D-Sub to 9P D-Sub: FBs communication module
eMT3000 series
COM1 RS232 9P COM3 RS232 9P FBs communication
D-Sub Female D-Sub Female module RS232 9P
D-Sub Male
2 RX 8 RX 2 TX
3 TX 7 TX 3 RX
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P FBs communication
D-Sub Female D-Sub Female D-Sub Male module RS232 9P
D-Sub Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 3 RX
5 GND 5 GND 5 GND 5 GND

85
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P FBs communication
D-Sub Female module RS232 9P
D-Sub Male
9 RX 2 TX
6 TX 3 RX
5 GND 5 GND

The following represents the cable end connector.

FBs communication module 3P Terminal Block
eMT3000 series
COM1 RS485 2W COM3 RS485 2W FBs communication
9P D-Sub Male 9P D-Sub Male module 3P Terminal
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W FBs communication
9P D-Sub Male 9P D-Sub Male module 3P Terminal
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND

86
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W FBs communication
9P D-Sub Female 9P D-Sub Female module 3P Terminal
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND

The following represents the cable end connector.

9P D-Sub to 15P D-Sub: CPU Port
eMT3000 series
COM1 RS232 9P COM3 RS232 9P FB CPU Port RS232
D-Sub Female D-Sub Female 15P D-Sub Male
2 RX 8 RX 2 TX
3 TX 7 TX 1 RX
5 GND 5 GND 6 GND
3 RTS
circuit
4 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P FB CPU Port RS232
D-Sub Female D-Sub Female D-Sub Male 15P D-Sub Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 1 RX
5 GND 5 GND 5 GND 6 GND
3 RTS
circuit
4 CTS

87
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P FB CPU Port RS232
D-Sub Female 15P D-Sub Male
9 RX 2 TX
6 TX 1 RX
5 GND 6 GND
3 RTS
circuit
4 CTS

The following represents the cable end connector.

9P D-Sub to 15P D-Sub: CPU Port RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W FB CPU Port RS485
9P D-Sub Male 9P D-Sub Male 2W 15P D-Sub Male
1 RX- 6 Data- 7 D-
2 RX+ 9 Data+ 5 D+
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W FB CPU Port RS485
9P D-Sub Male 9P D-Sub Male 2W 15P D-Sub Male
1 RX- 6 Data- 7 D-
2 RX+ 9 Data+ 5 D+
5 GND 5 GND

88
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W FB CPU Port RS485
9P D-Sub Female 9P D-Sub Female 2W 15P D-Sub Male
1 RX- 7 Data- 7 D-
2 RX+ 8 Data+ 5 D+
5 GND 5 GND

Driver Version:
Version Date Description
V1.60 Feb/17/2011 R_Bit, D_Bit and WS address types are added.
V1.70 Nov/29/2011 FR address types are added.

89
PLC Connection Guide

Fuji NB Series
Website: http://www.fujielectric.co.jp/fcs/eng/

HMI Setting:
Parameters Recommended Options Notes
PLC type Fuji NB Series
PLC I/F RS485 4W
Baud rate 19200
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. 0

PLC Setting:
Communication mode NITP Protocol / PLC Password (default is 0)

Device Address:
Bit/Word Device type Format Range Memo
B Y HHH 0 ~ 7ff Output Relay
B X HHH 0 ~ 3ff Input Relay
B M HHH 0 ~ fff Internal Relay
B L HHH 0 ~ fff Latch Relay
B C HH 0 - ff Counter
B M_Spe HHHH 0 ~ 81ff Special Relay
B T HHH 0 ~ 1ff Timer
W TV HHH 0 ~ 3ff Timer value
W CV HHH 0 ~ 3ff Counter value
W D HHHH 0 ~ 1fff Data Register
W D_Spe HHHH 0 ~ 81ff Special Register

90
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 4W Fuji NB Series RS422
9P D-Sub Male 8P RJ45 Male
1 RX- 4 TX-
2 RX+ 3 TX+
3 TX- 6 RX-
4 TX+ 5 RX+
5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W Fuji NB Series RS422
9P D-Sub Male 8P RJ45 Male
1 RX- 4 TX-
2 RX+ 3 TX+
3 TX- 6 RX-
4 TX+ 5 RX+
5 GND

MT6050i/MT8050i
COM1 RS485 4W Fuji NB Series RS422
9P D-Sub Female 8P RJ45 Male
1 RX- 4 TX-
2 RX+ 3 TX+
3 TX- 6 RX-
4 TX+ 5 RX+
5 GND

91
PLC Connection Guide

Driver Version:
Version Date Description
V1.10 May/05/2009

92
PLC Connection Guide

GE FANUC 0i MD
Website: http://www.fanucfa.com/welcome_worldwide/

HMI Setting:
Parameters Recommended Options Notes
PLC type GE FANUC 0i MD
PLC I/F RS232
Baud rate 19200
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 0

On-line simulation YES

PLC Setting:
Reader/Puncher interface (2ch.) is used for touch panel interface.
External touch panel interface, S/N: A02B-0320-J685, for Power Mate Series.

Device Address:
Bit/Word Device type Format Range Memo
B X DDDDo 0 ~ 11277
B Y DDDDo 0 ~ 11277
B K DDDo 0 ~ 9997
B E DDDDo 0 ~ 99997
B D_Bit DDDDo 0 ~ 99997
B R_Bit DDDDo 0 ~ 94997
W T DDDD 0 ~ 9499 Must be a multiple of 2
W C DDDD 0 ~ 5199 Must be a multiple of 4
W D_Byte DDDD 0 ~ 9999
W R_Byte DDDD 0 ~ 9499
W D DDDD 0 ~ 9999 Must be a multiple of 2
W R DDDD 0 ~ 9499 Must be a multiple of 2

93
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 20P JD36B or
D-Sub Female D-Sub Female JD54 Female
2 RX 8 RX 11 TX
3 TX 7 TX 1 RX
5 GND 5 GND 8(JD36) 4(JD54) GND
15 RTS
circuit
05 CTS
03 DR
07 CD circuit
13 ER

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 RS232 20P JD36B or
D-Sub Female D-Sub Female 9P D-Sub Male JD54 Female
2 RX 6 RX 8 RX 11 TX
3 TX 4 TX 7 TX 1 RX
5 GND 5 GND 5 GND 8(JD36) 4(JD54) GND
15 RTS
circuit
05 CTS
03 DR
07 CD circuit
13 ER

94
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 20P JD36B or
D-Sub Female JD54 Female
9 RX 11 TX
6 TX 1 RX
5 GND 8(JD36) 4(JD54) GND
15 RTS
circuit
05 CTS
03 DR
07 CD circuit
13 ER

Driver Version:
Version Date Description
V1.00 May/16/2011 Driver released.

95
PLC Connection Guide

GE Fanuc CMM
Website: http://www.ge.com

HMI Setting:
Parameters Recommended Options Notes
PLC type GE Fanuc CMM
PLC I/F RS232 RS232/RS485
9600,19200,38400,5
Baud rate 19200
7600,115200
Must set to 8 for this
Data bits 8 7,8
protocol
Parity Odd Even, Odd, None
Stop bits 1 1, 2
Does not apply to this
PLC sta. no. 0 0-255
protocol

PLC Setting:
Refer to the related PLC manual.

Device Address:
Bit/Word Device type Format Range Memo
B I DDDDD 1 ~ 10000 Input relay
B Q DDDDD 1 ~ 10000 Output relay
B M DDDDD 1 ~ 10000 Auxiliary relay
B G DDDD 1 ~ 7680
B T DDD 1 ~ 256
B SA DDD 1 ~ 128
B SB DDD 1 ~ 128
B SC DDD 1 ~ 128
B S DDD 1 ~ 128
W AI DDDDD 1 ~ 10000 Analog input register
W AQ DDDDD 1 ~ 10000 Analog output register
W R DDDDD 1 ~ 32640 Data register

96
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
CPU Port 90-30/VersaMax
eMT3000 series
COM1 RS485 4W 90-30/VersaMax RS485
9P D-Sub Male 4W 15P D-Sub Male
1 RX- 12 SDA
2 RX+ 13 SDB
5 GND 7 GND
3 TX- 10 RDA
4 TX+ 11 RDB
circuit
9 RT
6 RTSA
circuit
15 CTSA
8 RTSB
circuit
14 CTSB

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W 90-30/VersaMax RS485
9P D-Sub Male 4W 15P D-Sub Male
1 RX- 12 SDA
2 RX+ 13 SDB
5 GND 7 GND
3 TX- 10 RDA
4 TX+ 11 RDB
circuit
9 RT
6 RTSA
circuit
15 CTSA
8 RTSB
circuit
14 CTSB

97
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W 90-30/VersaMax RS485
9P D-Sub Female 4W 15P D-Sub Male
1 RX- 12 SDA
2 RX+ 13 SDB
5 GND 7 GND
3 TX- 10 RDA
4 TX+ 11 RDB
circuit
9 RT
6 RTSA
circuit
15 CTSA
8 RTSB
circuit
14 CTSB

The following represents the cable end connector.

CPU Port (90-30 series CPU351/352/363/364)
eMT3000 series
COM1 RS232 9P COM3 RS232 9P 90-30/90-70 series
D-Sub Female D-Sub Female RS232 6P RJ11 Male
2 RX 8 RX 2 TX
3 TX 7 TX 5 RX
5 GND 5 GND 3 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P 90-30/90-70 series
D-Sub Female D-Sub Female D-Sub Male RS232 6P RJ11 Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 5 RX
5 GND 5 GND 5 GND 3 GND

98
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P 90-30/90-70 series
D-Sub Female RS232 6P RJ11 Male
9 RX 2 TX
6 TX 5 RX
5 GND 3 GND

The following represents the cable end connector.

CPU Port (VersaMax series CPU001/002/005/E05)
eMT3000 series
COM1 RS232 9P COM3 RS232 9P VersaMax series RS232
D-Sub Female D-Sub Female 9P D-Sub Male
2 RX 8 RX 2 TX
3 TX 7 TX 3 RX
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P VersaMax series RS232
D-Sub Female D-Sub Female D-Sub Male 9P D-Sub Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 3 RX
5 GND 5 GND 5 GND 5 GND

99
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P VersaMax series RS232
D-Sub Female 9P D-Sub Male
9 RX 2 TX
6 TX 3 RX
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Jul/09/2009 Driver released.

100
PLC Connection Guide

GE FANUC RX3i
Website: http://www.ge.com

HMI Setting:
Parameters Recommended Options Notes
PLC type GE FANUC RX3i
PLC I/F RS232 RS232, RS485
Baud rate 19200 1200~115200
Data bits 8
Parity Odd None, Even, Odd
Stop bits 1 1 or 2
PLC sta. no. 1 1~99

PLC Setting:
Refer to the related PLC manual.

Device Address:
Bit/Word Device type Format Range Memo
B I DDDDD 1 ~ 32768
B Q DDDDD 1 ~ 32768
B M DDDDD 1 ~ 32768
B G DDDDD 1 ~ 32768
B T DDDDD 1 ~ 32768
B SA DDDDD 1 ~ 32768
B SB DDDDD 1 ~ 32768
B SC DDDDD 1 ~ 32768
B S DDDDD 1 ~ 32768
W AI DDDDD 1 ~ 32768
W AQ DDDDD 1 ~ 32768
W R DDDDD 1 ~ 32768

101
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P GE Fanuc RX3i COM1
D-Sub Female D-Sub Female RS232 9P D-Sub Male
2 RX 8 RX 2 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P GE Fanuc RX3i COM1
D-Sub Female D-Sub Female D-Sub Male RS232 9P D-Sub Male
2 RX 6 RX 8 RX 2 TXD
3 TX 4 TX 7 TX 3 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P GE Fanuc RX3i COM1
D-Sub Female RS232 9P D-Sub Male
9 RX 2 TXD
6 TX 3 RXD
5 GND 5 GND

102
PLC Connection Guide

The following represents the cable end connector.

GE Fanuc RX3i COM2
eMT3000 series
COM1 RS485 4W GE Fanuc RX3i COM2
9P D-Sub Male RS232 15P D-Sub Male
1 RX- 12 SDA
2 RX+ 13 SDB
5 GND 7 GND
3 TX- 10 RDA
4 TX+ 11 RDB
circuit
9 RT
6 RTSA
circuit
15 CTSA
8 RTSB
circuit
14 CTSB

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W GE Fanuc RX3i COM2
9P D-Sub Male RS232 15P D-Sub Male
1 RX- 12 SDA
2 RX+ 13 SDB
5 GND 7 GND
3 TX- 10 RDA
4 TX+ 11 RDB
circuit
9 RT
6 RTSA
circuit
15 CTSA
8 RTSB
circuit
14 CTSB

103
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W GE Fanuc RX3i COM2
9P D-Sub Female RS232 15P D-Sub Male
1 RX- 12 SDA
2 RX+ 13 SDB
5 GND 7 GND
3 TX- 10 RDA
4 TX+ 11 RDB
circuit
9 RT
6 RTSA
circuit
15 CTSA
8 RTSB
circuit
14 CTSB

Driver Version:
Version Date Description
V1.10 Oct/01/2010 Driver released.

104
PLC Connection Guide

GE Fanuc Series 90-30 (Ethernet)

Supported Series: GE 90-30 series, CPU model 374plus.

HMI Setting:
Parameters Recommended Options Notes
PLC type GE Fanuc Series 90-30 (Ethernet)
PLC I/F Ethernet
Port no. 18245
PLC sta. no. 1 1~99

Device Address:
Bit/Word Device type Format Range Memo
B I_bit DDDDD 1 ~ 32768
B Q_bit DDDDD 1 ~ 32768
B M_bit DDDDD 1 ~ 32768
B G_bit DDDDD 1 ~ 32768
B T_bit DDDDD 1 ~ 32768
B SA_bit DDDDD 1 ~ 32768 Read Only
B SB_bit DDDDD 1 ~ 32768 Read Only
B SC_bit DDDDD 1 ~ 32768 Read Only
B S_bit DDDDD 1 ~ 32768 Read Only
B R_bit DDDDD 1 ~ 32768
Address increment by 8 words, ex: I1,
W I DDDDD 1 ~ 32753
I9, I17, I25…..
The rule is same as above, ex:Q1, Q9,
W Q DDDDD 1 ~ 32753
Q17…
The rule is same as above, ex:M1,
W M DDDDD 1 ~ 32753
M9, M17..
The rule is same as above, ex:G1, G9,
W G DDDDD 1 ~ 32753
G17…
The rule is same as above, ex:T1, T9,
W T DDDD 1 ~ 1024
T17….
W SA DDDDD 1 ~ 32753 Read only, the rule is same as above
W SB DDDDD 1 ~ 32753 Read only, the rule is same as above

105
PLC Connection Guide

Bit/Word Device type Format Range Memo

W SC DDDDD 1 ~ 32753 Read only, the rule is same as above
W S DDDDD 1 ~ 32753 Read only, the rule is same as above
W R DDDDD 1 ~ 32768
W AI DDDDD 1 ~ 32768
W AQ DDDDD 1 ~ 32768
W W DDDDDDD 1 ~ 5000000

106
PLC Connection Guide

Driver Version:
Version Date Description
V1.70 Apr/09/2010
V1.80 Nov/09/2011 Add device type : R_bit
V1.90 Jan/17/2012 Add device type : W

107
PLC Connection Guide

GE Fanuc SNP-X
Supported Series: GE Fanuc 90 & VersaMax series PLC

Website: http://www.ge.com

HMI Setting:
Parameters Recommended Options Notes
PLC type GE Fanuc SNP-X
PLC I/F RS485 4w RS232/RS485
9600, 19200, 38400,
Baud rate 19200
57600, 115200
Data bits 8 7, 8 Must set to 8 for this protocol
Parity Odd Even, Odd, None
Stop bits 1 1, 2
PLC sta. no. 0 0-255 Does not apply to this protocol

PLC Setting:
Refer to the related PLC manual.

108
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
CPU Port (90-30/VersaMax)
eMT3000 series
COM1 RS485 4W 90-30/VersaMax RS422
9P D-Sub Male 15P D-Sub Male
1 RX- 12 SDA
2 RX+ 13 SDB
5 GND 7 GND
3 TX- 10 RDA
4 TX+ 11 RDB
circuit
9 RT
6 RTSA
circuit
15 CTSA
8 RTSB
circuit
14 CTSB

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W 90-30/VersaMax RS422
9P D-Sub Male 15P D-Sub Male
1 RX- 12 SDA
2 RX+ 13 SDB
5 GND 7 GND
3 TX- 10 RDA
4 TX+ 11 RDB
circuit
9 RT
6 RTSA
circuit
15 CTSA
8 RTSB
circuit
14 CTSB

109
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W 90-30/VersaMax RS422
9P D-Sub Female 15P D-Sub Male
1 RX- 12 SDA
2 RX+ 13 SDB
5 GND 7 GND
3 TX- 10 RDA
4 TX+ 11 RDB
circuit
9 RT
6 RTSA
circuit
15 CTSA
8 RTSB
circuit
14 CTSB

The following represents the cable end connector.

CPU Port (90-30 series CPU351/352/363/364)
eMT3000 series
COM1 RS232 9P COM3 RS232 9P 90-30/90-70 series
D-Sub Female D-Sub Female RS232 6P RJ11 Male
2 RX 8 RX 2 TX
3 TX 7 TX 5 RX
5 GND 5 GND 3 GND

MT6000/8000 series excepts MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P 90-30/90-70 series
D-Sub Female D-Sub Female D-Sub Male RS232 6P RJ11 Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 5 RX
5 GND 5 GND 5 GND 3 GND

110
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P 90-30/90-70 series
D-Sub Female RS232 6P RJ11 Male
9 RX 2 TX
6 TX 5 RX
5 GND 3 GND

The following represents the cable end connector.

CPU Port (VersaMax series CPU001/002/005/E05)
eMT3000 series
COM1 RS232 9P COM3 RS232 9P VersaMax series RS232
D-Sub Female D-Sub Female 9P D-Sub Male
2 RX 8 RX 2 TX
3 TX 7 TX 3 RX
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P VersaMax series RS232
D-Sub Female D-Sub Female D-Sub Male 9P D-Sub Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 3 RX
5 GND 5 GND 5 GND 5 GND

111
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P VersaMax series RS232
D-Sub Female 9P D-Sub Male
9 RX 2 TX
6 TX 3 RX
5 GND 5 GND

Driver Version:
Version Date Description
V1.20 Jan/09/2009

112
PLC Connection Guide

Haiwell PLC
Support Series: E series, S series and H series.
Web: http://www.haiwell.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Haiwell PLC
PLC I/F RS232 RS232,RS485 2W
Baud rate 19200 19200
Data bits 8 8
Parity None None
Stop bits 2 2
PLC sta. no. 1 1~247

Device Address:
Bit/Word Device type Format Range Memo
B X DDDD 0 ~ 1023 Input Switch
B Y DDDD 0 ~ 1023 Output Switch
B M DDDDD 0 ~ 12287 Internal Relay
B T DDDD 0 ~ 1023 Timer (Output Coil State)
B C DDD 0 ~ 255 Timer (Output Coil State)
B SM DDD 0 ~ 215 System Status Bit
B S DDDD 0 ~ 2047 Step Bit
Special Module Parameter
W CR DD 0 ~ 79
Register
W AI DDD 0 ~ 255 Analog Input Register
W AQ DDD 0 ~ 255 Analog Output Register
W V DDDDD 0 ~ 14847 Data Register
W TCV DDDD 0 ~ 1023 Timer (current value register)
W CCV DDD 0 ~ 255 Timer (current value register)
W SV DDD 0 ~ 154 System Register

113
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 4P Mini-DIN
D-Sub Female D-Sub Female Male
2 RX 8 RX 2 TX
3 TX 7 TX 1 RX
5 GND 5 GND 3 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 4P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 1 RX
5 GND 5 GND 5 GND 3 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 4P Mini-DIN
D-Sub Female Male
9 RX 2 TX
6 TX 1 RX
5 GND 3 GND

114
PLC Connection Guide
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W Terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- B- Data+
2 RX+ 9 Data+ A+ Data-
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W Terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- B- Data+
2 RX+ 9 Data+ A+ Data-
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W Terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- B- Data+
2 RX+ 8 Data+ A+ Data-
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Mar/2/2012 Driver released.

115
PLC Connection Guide

Hanyoung Controller
Supported Series: Temperature Controller.

Website: http://hynux.com/kor/

HMI Setting:
Parameters Recommended Options Notes
PLC type Hanyoung Controller
PLC I/F RS485 4W
Baud rate 9600
Data bits 8 7 or 8
Parity None Even, Odd, None
Stop bits 1 1 or 2
PLC sta. no. 1 0-255

*In System Parameter Settings / Device Settings / COM Settings, set Parameter 1 to “1” to
support Check Sum Mode.

116
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
B I DDDD 1 ~ 9999
W D DDDD 1 ~ 9999

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 4W Han Young RS422
9P D-Sub Male terminal
1 RX- 32 TX-
2 RX+ 31 TX+
3 TX- 34 RX-
4 TX+ 33 RX+
5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W Han Young RS422
9P D-Sub Male terminal
1 RX- 32 TX-
2 RX+ 31 TX+
3 TX- 34 RX-
4 TX+ 33 RX+
5 GND

117
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W Han Young RS422
9P D-Sub Female terminal
1 RX- 32 TX-
2 RX+ 31 TX+
3 TX- 34 RX-
4 TX+ 33 RX+
5 GND

Driver Version:
Version Date Description
V1.60 Jun/14/2010

118
PLC Connection Guide

HAWE PLVC
Supported Series: HAWE PLVC

Website: http://www.hawe.de/de/home/

HMI Setting:
Parameters Recommended Options Notes
PLC type HAWE PLVC
PLC I/F RS232
Baud rate 9600
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B X HHHH 0 ~ ffff Input Bits
B Y HHHH 0 ~ ffff Output Bits
B M DDDDD 0 ~ 65535 Internal Relays
B T DDDDD 0 ~ 65535
B C DDDDD 0 ~ 65535
B B HHHH 0 ~ ffff
B F DDDDD 0 ~ 65535
W TV DDDDD 0 ~ 65535 Timer Preset Value
W CV DDDDD 0 ~ 65535 Counter Preset Value
W D DDDDD 0 ~ 65535 Data Registers
W W HHHH 0 ~ ffff
W R DDDDD 0 ~ 65535

119
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 terminal
D-Sub Female D-Sub Female
2 RX 8 RX TXD
3 TX 7 TX RXD
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 terminal
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS232 9P RS232 terminal
D-Sub Female
9 RX TXD
6 TX RXD
5 GND GND

Driver Version:
Version Date Description
V1.00 Sep/17/2009

120
PLC Connection Guide

Heng Yuan EU series

Supported Series: EU sereis, EU5 series, EU10 series.

Website: http://www.tjhysensor.cn/

HMI Setting:
Parameters Recommended Options Notes
PLC type Heng Yuan EU series
PLC I/F RS485 2W
Baud rate 9600
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 2 1-31

Online simulator YES

Extend address mode YES

Device Address:
Bit/Word Device type Format Range Memo
W Parameter DDDD 0 ~ 2000

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W Heng Yuan Sensor
9P D-Sub Male 9P D-Sub Male RS485
1 RX- 6 Data- 7 RX- (Yellow)
2 RX+ 9 Data+ 6 RX+ (Green)
5 GND 5 GND 4 GND (Black)

121
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W Heng Yuan Sensor
9P D-Sub Male 9P D-Sub Male RS485
1 RX- 6 Data- 7 RX- (Yellow)
2 RX+ 9 Data+ 6 RX+ (Green)
5 GND 5 GND 4 GND (Black)

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W Heng Yuan Sensor
9P D-Sub Female 9P D-Sub Female RS485
1 RX- 7 Data- 7 RX- (Yellow)
2 RX+ 8 Data+ 6 RX+ (Green)
5 GND 5 GND 4 GND (Black)

Driver Version:
Version Date Description
V1.00 Dec/30/2008 Driver released.

122
PLC Connection Guide

Hitachi EH-SIO
HMI Setting:
Parameters Recommended Options Notes
PLC type Hitachi EH-SIO
PLC I/F RS232 RS232, RS485
Baud rate 19200 9600, 19200, 38400
Data bits 7 7
Parity Even Even
Stop bits 1 1
PLC sta. no. 0

PLC Setting:
Communication mode 19200, E, 7, 1 (default)

Device Address:
Bit/Word Device type Format Range Memo
B X HHHHh 0 ~ fffff External input-bit (X)
B Y HHHHh 0 ~ fffff External output-bit (Y)
B M HHHHh 0 ~ fffff Data area-bit (M)
B T HHHHh 0 ~ fffff Timer (T)
B R HHHHh 0 ~ fffff Internal output (R)
B L HHHHh 0 ~ fffff Link area-bit (L)
W TC HH 0 ~ ff Timer/Counter current value
W WM HHHH 0 ~ 270f Data area-word (M)
W WX HHHH 0 ~ 270f External input-word (X)
W WY HHHH 0 ~ 270f External output-word (Y)
W WR HHHH 0 ~ 270f Internal output-word (R)
W WL HHHH 0 ~ 270f Link area-word (L)

123
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
EH-SIO port1/port 2 RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 8P RJ45 Male
D-Sub Female D-Sub Female
2 RX 8 RX 5 SD
3 TX 7 TX 6 RD
5 GND 5 GND 1 SG
8 CTS 8 RS
4 PHL
circuit
7 DR

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 8P RJ45 Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 5 SD
3 TX 4 TX 7 TX 6 RD
5 GND 5 GND 5 GND 1 SG
8 CTS 8 RS
4 PHL
circuit
7 DR

124
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 8P RJ45 Male
D-Sub Female
9 RX 5 SD
6 TX 6 RD
5 GND 1 SG
8 RS
4 PHL
circuit
7 DR

The following represents the cable end connector.

EH-SIO port2 RS485 4W
eMT3000 series
COM1 RS485 4W Hitachi EH-SIO
9P D-Sub Male
1 RX- 2 TX-
2 RX+ 1 TX+
3 TX- 4 RX-
4 TX+ 3 RX+
5 GND 6 SG

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W Hitachi EH-SIO
9P D-Sub Male
1 RX- 2 TX-
2 RX+ 1 TX+
3 TX- 4 RX-
4 TX+ 3 RX+
5 GND 6 SG

125
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W Hitachi EH-SIO
9P D-Sub Female
1 RX- 2 TX-
2 RX+ 1 TX+
3 TX- 4 RX-
4 TX+ 3 RX+
5 GND 6 SG

The following represents the cable end connector.

EH-SIO port2 RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W Hitachi EH-SIO
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 2 TX-
circuit
4 RX-
2 RX+ 9 Data+ 1 TX+
circuit
3 RX+
5 GND 5 GND 6 SG

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W Hitachi EH-SIO
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 2 TX-
circuit
4 RX-
2 RX+ 9 Data+ 1 TX+
circuit
3 RX+
5 GND 5 GND 6 SG

126
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W Hitachi EH-SIO
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- 2 TX-
circuit
4 RX-
2 RX+ 8 Data+ 1 TX+
circuit
3 RX+
5 GND 5 GND 6 SG

Driver Version:
Version Date Description
V1.00 May/25/2010 Driver released.

127
PLC Connection Guide

Hitachi EHV Series (Ethernet)

Website: http://www.hitachi-ies.co.jp/english/products/plc/index.htm

HMI Setting:
Parameters Recommended Options Notes
PLC type Hitachi EHV Series (Ethernet)
PLC I/F Ethernet
Port no. 3004 3004~3007

Device Address:
Bit/Word Device type Format Range Memo
B X HHHHh 0 ~ fffff External input-bit (X)
B Y HHHHh 0 ~ fffff External output-bit (Y)
B M HHHHh 0 ~ fffff Data area-bit (M)
B T DDDDD 0 ~ 65535 Timer (T)
B R HHHHh 0 ~ fffff Internal output (R)
B L HHHHh 0 ~ fffff Link area-bit (L)
W TC DDDD 0 ~ 2559 Timer/Counter current value
W WM HHHH 0 ~ 7fff Data area-word (M)
W WX HHHH 0 ~ ffff External Input-word (X)
W WY HHHH 0 ~ ffff External output-word (Y)
W WR HHHH 0 ~ ffff Internal output-word (R)
W WL HHHH 0 ~ 73ff Link area-word (L)

128
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 Jan/12/2010 Driver released

129
PLC Connection Guide

Hitachi H/EH/EHV Series

Supported Series: Hitachi H series, EH-150, Micro-EH, H20, H40, H64, H200, H250, H252,
H300, H302, H700, H702, H1000, H1002, H2000, H4010.

Website: http://www.hitachi-ies.co.jp/english/products/plc/index.htm

HMI Setting:
Parameters Recommended Options Notes
PLC type Hitachi H/EH/EHV Series
PLC I/F RS232 RS232, RS485
Baud rate 19200 9600, 19200, 38400
Data bits 7 7
Parity Even Even
Stop bits 1 1
Does not apply to this
PLC sta. no. 0 0-255
protocol.

Online simulator YES Broadcast command NO

Extend address mode NO

Device Address:
Bit/Word Device type Format Range Memo
B X HHHHh 0 ~ fffff External input-bit (X)
B Y HHHHh 0 ~ fffff External output-bit (Y)
B M HHHHh 0 ~ fffff Data area-bit (M)
B T HHHHh 0 ~ fffff Timer (T)
B R HHHHh 0 ~ fffff Internal output (R)
B L HHHHh 0 ~ fffff Link area-bit (L)
W TC HH 0 ~ ff Timer/Counter current value
W WM HHHH 0 ~ 270f Data area-word (M)
W WX HHHH 0 ~ 270f External input-word (X)
W WY HHHH 0 ~ 270f External output-word (Y)
W WR HHHH 0 ~ c3ff Internal output-word (R)
W WL HHHH 0 ~ 270f Link area-word (L)

130
PLC Connection Guide

Wiring Diagram:
WARNING: If your communication cable is not wired exactly as shown in our cable
assembly instructions, damage to the HMI or loss of communications can be caused.

CPU TYPE Port 1 Port 2

EH-150/CPU 104A RS-232 RS-232
EH-150/CPU 208A RS-232 RS-232
Port 1 EH-150/CPU 308A RS-232/RS-485 RS-232

Port 2 EH-150/CPU 316A RS-232/RS-485 RS-232

EH-150/CPU 448A RS-232/RS-485 RS-232

Switch Number
1 OFF Normal mode
2 OFF TRNS0 operation
3, 4 3 4 Port1 transmission speed
ON ON 4,800 bps Doesn’t support
OFF ON 9,600 bps
ON OFF 19,200 bps Default
OFF OFF 38,400 bps
5 ON Dedicated port
6 6 PHL Port2 transmission speed
ON Low 9,600 bps Toggle-Switch
ON High 38,400 bps PHL
OFF Low 4,800 bps Doesn’t support Low
OFF High 19,200 bps Default
7 OFF (System mode) Do not turn on. PHL
8 OFF (System mode) Do not turn on. High

131
PLC Connection Guide
The following represents the cable end connector.
EH-150 port1/port 2 RS232 / MICRO-EH port1 RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 8P RJ45 Male
D-Sub Female D-Sub Female
2 RX 8 RX 5 SD
3 TX 7 TX 6 RD
5 GND 5 GND 1 SG
8 CTS 8 RS
4 PHL
circuit
7 DR

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 8P RJ45 Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 5 SD
3 TX 4 TX 7 TX 6 RD
5 GND 5 GND 5 GND 1 SG
8 CTS 8 RS
4 PHL
circuit
7 DR

MT6050i/MT8050i
COM1 RS232 9P RS232 8P RJ45 Male
D-Sub Female
9 RX 5 SD
6 TX 6 RD
5 GND 1 SG
8 RS
4 PHL
circuit
7 DR

132
PLC Connection Guide
The following represents the cable end connector.
EH-150 port1 RS485 4W
eMT3000 series
COM1 RS485 4W RS485 4W 8P RJ45
9P D-Sub Male Male
1 RX- 5 TX-
2 RX+ 4 TX+
3 TX- 6 RX-
4 TX+ 7 RX+
5 GND 1 SG

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 8P RJ45
9P D-Sub Male Male
1 RX- 5 TX-
2 RX+ 4 TX+
3 TX- 6 RX-
4 TX+ 7 RX+
5 GND 1 SG

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 8P RJ45
9P D-Sub Female Male
1 RX- 5 TX-
2 RX+ 4 TX+
3 TX- 6 RX-
4 TX+ 7 RX+
5 GND 1 SG

133
PLC Connection Guide
The following represents the cable end connector.
EH-150 port1 RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P RJ45
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 4 TX+
circuit
7 RX+
2 RX+ 9 Data+ 5 TX-
circuit
6 RX-
5 GND 5 GND 1 SG

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 8P RJ45
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 4 TX+
circuit
7 RX+
2 RX+ 9 Data+ 5 TX-
circuit
6 RX-
5 GND 5 GND 1 SG

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P RJ45
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 4 TX+
circuit
7 RX+
2 RX+ 8 Data+ 5 TX-
circuit
6 RX-
5 GND 5 GND 1 SG

134
PLC Connection Guide
The following represents the cable end connector.
H Series CPU Port RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 15P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 2 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 9 SG
circuit
10 SG
8 CTS 4 RTS
5 CTS
7 DSR
circuit
8 PHL
14 PV12

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 15P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 2 TXD
3 TX 4 TX 7 TX 3 RXD
5 GND 5 GND 5 GND 9 SG
circuit
10 SG
8 CTS 4 RTS
5 CTS
7 DSR
circuit
8 PHL
14 PV12

135
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 15P D-Sub Male
D-Sub Female
9 RX 5 SD
6 TX 6 RD
5 GND 1 SG
circuit
8 RS
5 CTS
7 DSR
circuit
8 PHL
14 PV12

Driver Version:
Version Date Description
V1.10 Oct/22/2009 Fixed HMI occupies the control right of CPU module.
V1.30 Mar/22/2010

136
PLC Connection Guide

HUST H4X
Supported Series: HUST CNC Controller H4 Series.
Website: http://www.hust.com.tw/

HMI Setting:
Parameters Recommended Options Notes
PLC type HUST H4X
PLC I/F RS-232 CPU port
Baud rate 38400 9600,19200,38400,57600
Data bits 7
Parity Even
Stop bits 2
Turn around delay 5
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
Mapping to VM 10800 ~ 10807 (read
B I DDD 0 ~ 255
only)
Mapping to VM 10808 ~ 10815 (read
B O DDD 0 ~ 255
only)
Mapping to VM 10816 ~ 10823 (read
B C DDD 0 ~ 255
only)
Mapping to VM 10824 ~ 10831 (read
B S DDD 0 ~ 255
only)
Mapping to VM 10832 ~ 10863 (read
B A DDD 0 ~ 255
only)

B VM_bit DDDDDdd 100 ~ 9999931 Bit address (dd): 00 ~ 31

Please refer to the controller

DW VM DDDDD 1 ~ 99999
specification for register range.
Mapping to VM 10000 ~ 10255 (read
DW R DDD 0 ~ 255
only)
Mapping to VM 10256 ~ 10511 (read
DW Cn DDD 0 ~ 255
only)
Mapping to VM 10512 ~ 10767 (read
DW Tm DDD 0 ~ 255
only)

137
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P HUST CNC Controller
D-Sub Female D-Sub Female RS232 D-Sub Male
2 RX 8 RX 2 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P HUST CNC Controller
D-Sub Female D-Sub Female D-Sub Male RS232 D-Sub Male
2 RX 6 RX 8 RX 2 TXD
3 TX 4 TX 7 TX 3 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P HUST CNC Controller
D-Sub Female RS232 D-Sub Male
9 RX 2 TXD
6 TX 3 RXD
5 GND 5 GND

Driver Version:
Version Date Description
V2.01 Sep/29/2009

138
PLC Connection Guide

IAI X-SEL CONTROLLER

Website: http://www.iai-robot.co.jp/

HMI Setting:
Parameters Recommended Options Notes
PLC type IAI X-SEL CONTROLLER
PLC I/F RS232
Baud rate 9600 9600~19200
Data bits 7 7 or 8
Parity None Even, Odd, None
Stop bits 1 1 or 2
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
Address 1~8 represent the corresponding
W Servo_On_Off H 1~8 axis.
Write 1 means ON and 0 means OFF.
Address 1~8 represent the corresponding
W Servo_Origin H 1~8 axis.
Back to origin.
For reading current position. The state of
current axis is put in RW axis*100.
W CurrentAxisPos H 1~8
i.e., for the state of axis 2, 2*100=200, so it
is in RW200.
Data written indicates which program to
W RunProgram H 0
run.
Data written indicates which program to
W EndProgram H 0
stop.
Address 1~8 represent the corresponding
axis. The data written indicates which point
W PointMove H 0~8 to reach. Put parameters ACC, DEC,
SPEED in axis*100+1, axis*100+2 and
axis*100+3 respectively.

139
PLC Connection Guide
Bit/Word Device type Format Range Memo
Jogging. Address 1~8 represent the
corresponding axis. Put parameters ACC,
W JoggingMove H 0~8 DEC, SPEED and Position in axis*100+11,
axis*100+12, axis*100+13 and
axis*100+14 respectively.
Jog to the set absolute coordinate. Address
1~8 represent the corresponding axis. Put
W AbsoluteMove H 0~8 parameters ACC, DEC, SPEED and
Position in axis*100+21, axis*100+22,
axis*100+23 and axis*100+24 respectively.
To change the value of the point. Address
1~8 represent the corresponding axis. Put
W PointChange H 0~8 parameters ACC, DEC, SPEED and
Position in axis*100+31, axis*100+32,
axis*100+33 and axis*100+34 respectively.
W SoftWareReset H 0 Reset soft ware.
Note: ddd: Decimal, hhh: Hexadecimal, ooo: Octal.
Each model of CPU is different; it is recommended to refer to PLC Manual Device List.

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P Host RS232 D-Sub
D-Sub Female D-Sub Female Female
2 RX 8 RX 3 TX
3 TX 7 TX 2 RX
5 GND 5 GND 5 GND

140
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P Host RS232 D-Sub
D-Sub Female D-Sub Female D-Sub Male Female
2 RX 6 RX 8 RX 3 TX
3 TX 4 TX 7 TX 2 RX
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P Host RS232 D-Sub
D-Sub Female Female
9 RX 3 TX
6 TX 2 RX
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Jun/01/2010 Driver released.

141
PLC Connection Guide

IDEC Micro
Supported Series: IDEC Micro3, Micro3C, MicroSmart, OpenNet Controller series.

Website: http://www.idec.com

HMI Setting:
Parameters Recommended Options Notes
PLC type IDEC Micro
PLC I/F RS232 RS232, RS485
Baud rate 9600 9600, 19200
Data bits 7 7, 8
Parity Even Even, Odd, None
Stop bits 1 1
255 (for 1:1 255 or same as the PLC
PLC sta. no. 0-255
connect) setting

Online simulator YES

Extend address mode YES Do not set the PLC Station No. to 255

PLC Setting:
Communication mode 9600, E, 7, 1 (default), Use Computer Link Protocol

Device Address:
Bit/Word Device type Format Range Memo
B X DDDDo 0 ~ 20477 Input (I)
B Y DDDDo 0 ~ 20477 Output (Q)
B M DDDDo 0 ~ 20477 Internal Relay (M)
W RT DDDD 0 ~ 9999 Timer (T)
W RC DDDD 0 ~ 9999 Counter (C)
W D DDDD 0 ~ 9999 Data Register (D)

142
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
Micro3C, MicroSmart, OpenNet Controller CPU Ladder Port
eMT3000 series
COM1 RS232 9P COM3 RS232 9P Port1 or Port2 RS232
D-Sub Female D-Sub Female 8P Mini-DIN Male
2 RX 8 RX 3 TXD
3 TX 7 TX 4 RXD
5 GND 5 GND 7 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P Port1 or Port2 RS232
D-Sub Female D-Sub Female D-Sub Male 8P Mini-DIN Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 7 GND

MT6050i/MT8050i
COM1 RS232 9P Port1 or Port2 RS232
D-Sub Female 8P Mini-DIN Male
9 RX 3 TXD
6 TX 4 RXD
5 GND 7 GND

143
PLC Connection Guide
The following represents the cable end connector.
Micro3 CPU Port, MicroSmart with FC4A-PC2 RS485 Communication Adapter
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 8P Mini-DIN
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 2 RXD-
2 RX+ 9 Data+ 1 RXD+
5 GND 5 GND 7 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 8P Mini-DIN
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 2 RXD-
2 RX+ 9 Data+ 1 RXD+
5 GND 5 GND 7 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 8P Mini-DIN
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 2 RXD-
2 RX+ 8 Data+ 1 RXD+
5 GND 5 GND 7 GND

144
PLC Connection Guide
The following represents the cable end connector.
Micro3C, OpenNet Controller Data Link Terminals,MicroSmart with FC4A-PC3 RS485
Communication Adapter
eMT3000 series
COM1 RS485 2W COM3 RS485 2W Data Link Terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- A RXD-
2 RX+ 9 Data+ B RXD+
5 GND 5 GND SG GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W Data Link Terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- A RXD-
2 RX+ 9 Data+ B RXD+
5 GND 5 GND SG GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W Data Link Terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- A RXD-
2 RX+ 8 Data+ B RXD+
5 GND 5 GND SG GND

Driver Version:
Version Date Description
V1.20 Jun/19/2009

145
PLC Connection Guide

Inovance H2U/H1U
Website: http://www.inovance.cn/

HMI Setting:
Parameters Recommended Options Notes
PLC type Inovance H2U/H1U
PLC I/F RS485 4W
Baud rate 9600 9600~19200
Data bits 7 7 or 8
Parity Even Even, Odd, None
Stop bits 1 1 or 2
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B X OOO 0 ~ 377 Input Bits
B Y OOO 0 ~ 377 Output Bits
B M DDDD 0 ~ 7999 Auxiliary Relay
B T DDD 0 ~ 255 Timer Relay
B C DDD 0 ~ 255 Counter Relay
B SM DDDD 8000 ~ 9999 Special Auxiliary Relay
B D_Bit DDDDdd 0 ~ 799915
B S DDDD 0 ~ 4095
W TV DDD 0 ~ 255 Timer Memory
W CV DDD 0 ~ 199 Counter Memory
W D DDDD 0 ~ 7999 Data Registers
DW CV2 DDD 200 ~ 255 Counter Memory (32bit)
W SD DDDD 8000 ~ 9999 Special Data Register
Note: ddd: Decimal, hhh: Hexadecimal, ooo: Octal.
Each model of CPU is different, it is recommended to refer to PLC Manual Device List.

146
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 4W H2U/H1U RS422 8P
9P D-Sub Male Mini-DIN Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W H2U/H1U RS422 8P
9P D-Sub Male Mini-DIN Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

MT6050i/MT8050i
COM1 RS485 4W H2U/H1U RS422 8P
9P D-Sub Female Mini-DIN Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

147
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 May/19/2010 Driver released.

148
PLC Connection Guide

Justfi Controller
Supported Series: Justfi weighing instruments, Industrial Batching Controller supports
XK31CB4, XK31CB6.

Website: http://www.justfi.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Justfi controller
PLC I/F RS232
Baud rate 9600 9600, 19200
Data bits 7 7 or 8
Parity Even Even, Odd, None
Stop bits 1 1 or 2
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
W Func DD 0 ~ 99 Read / Write
DW Func_DW DD 0 ~ 99 Read / Write
W RW H 0 Weight (read only)
W RF H 0 Read result (read only)
W RT H 0 Read total (read only)
W RG H 0 Read prescription group
W RC H 0 Circle
W RB H 0 Read status (read only)
W MZ H 0 Zero (write only)
W MT H 0 Tare (write only)
W CT H 0 Clear tare (write only)
W DT H 0 Clear total (write only)
W BB H 0 Start (write only)
W HB H 0 Stop (write only)
W BD H 0 Discharge (write only)
RP1t
W …. H 0 Read/Write recipe
RP6F

149
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P CB4 RS232
D-Sub Female D-Sub Female
2 RX 8 RX TD
3 TX 7 TX RD
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P CB4 RS232
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX TD
3 TX 4 TX 7 TX RD
5 GND 5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS232 9P CB4 RS232
D-Sub Female
9 RX TD
6 TX RD
5 GND GND

Driver Version:
Version Date Description
V1.40 Nov/04/2009

150
PLC Connection Guide

Kernel sistemi DMX Series

Supported Series: Kernel systemi DMX 30

Website: http://www.kernel.modena.it/

HMI Setting:
Parameters Recommended Options Notes
PLC type Kernel sistemi DMX Series
PLC I/F RS232 RS485
Baud rate 19200 9600
Data bits 8
Parity None
Stop bits 1
Must match the PLC port
PLC sta. no. 1
setting

Device Address:
Bit/Word Device type Format Range Memo
W D HHHH 0 ~ ffff

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P DMX30 RS232 9P
D-Sub Female D-Sub Female D-Sub Male
2 RX 8 RX 3 TX
3 TX 7 TX 2 RX
5 GND 5 GND 5 GND

151
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P DMX30 RS232 9P
D-Sub Female D-Sub Female D-Sub Male D-Sub Male
2 RX 6 RX 8 RX 3 TX
3 TX 4 TX 7 TX 2 RX
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P DMX30 RS232 9P
D-Sub Female D-Sub Male
9 RX 3 TX
6 TX 2 RX
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Feb/06/2010 Driver releasesd.

152
PLC Connection Guide

KEYENCE KV-10/16/24/40/80/Visual KV Series

Supported Series: KEYENCE KV series, KV16~80

Website: http://www.keyence.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type KEYENCE KV-10/16/24/40/80/Visual KV Series
PLC I/F RS232 RS232
Baud rate 9600
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B RLY DDDdd0* 0 ~ 655150* dd:0 ~ 15
B DM_Bit DDDDDh 0 ~ 65535f
W DM DDDDD 0 ~ 65535
W TM DDDD 0 ~ 8999
W T DDDD 0 ~ 9999
W T_Curr DDDD 0 ~ 9999 Timer_Current
W T_Preset DDDD 0 ~ 9999
W C DDDD 0 ~ 9999
W C_Curr DDDD 0 ~ 9999 Counter_Current
W C_Preset DDDD 0 ~ 9999
Note:*
If Relay (bit) register is used, please place a zero at the end of the address.
For example, to read Relay (bit) 100, the address is written as “1000”.

153
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
RS232 CPU Port:
eMT3000 series
COM1 RS232 9P COM3 RS232 9P OP-26486 9P D-Sub
D-Sub Female D-Sub Female Male
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P OP-26486 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P OP-26486 9P D-Sub
D-Sub Female Male
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND

154
PLC Connection Guide
The following represents the cable end connector.
9P D-Sub to 6P RJ11:
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 6P RJ11 Male
D-Sub Female D-Sub Female
2 RX 8 RX 2 TXD
3 TX 7 TX 4 RXD
5 GND 5 GND 3 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 6P RJ11 Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 2 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 3 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 6P RJ11 Male
D-Sub Female
9 RX 2 TXD
6 TX 4 RXD
5 GND 3 GND

Driver Version:
Version Date Description
V1.40 Apr/17/2009

155
PLC Connection Guide

KEYENCE KV-5000 (Ethernet)

Supported series: KV5000, 3000, 1000 series.

Website: http://www.keyence.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type KEYENCE KV-5000 (Ethernet)
PLC I/F Ethernet
Port no. 8501
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B MR DDDdd 0 ~ 99915
B LR DDDdd 0 ~ 99915
B CR DDDdd 0 ~ 99915
B RLY DDDdd 0 ~ 99915
W DM DDDDD 0 ~ 65535
W TM DDDD 0 ~ 9999
W T DDDD 0 ~ 9999
W T_Curr DDDD 0 ~ 9999 Timer Current
W T_Preset DDDD 0 ~ 9999 Timer Preset
W C DDDD 0 ~ 9999
W C_Curr DDDD 0 ~ 9999
W C_Preset DDDD 0 ~ 9999
W CM DDDDD 0 ~ 65535
W EM DDDDD 0 ~ 65535
W FM DDDDD 0 ~ 65535
Note:
If RLY (bit) register is used, please place a zero at the end of the address.
For example, to read RLY 100, the address is written as “1000”.

156
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 Dec/25/2009 Driver released.

157
PLC Connection Guide

KEYENCE KV-700/1000/3000/5000 Series

Website: http://www.keyence.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type KEYENCE KV-700/1000/3000/5000 Series
PLC I/F RS232 RS232
Baud rate 115200
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B MR DDDdd 0 ~ 99915
B LR DDDdd 0 ~ 99915
B CR DDDdd 0 ~ 99915
B RLY DDDdd 0 ~ 99915
W DM DDDDD 0 ~ 65535
W TM DDDD 0 ~ 9999
W T DDDD 0 ~ 9999
W T_Curr DDDD 0 ~ 9999 Timer_Current
W T_Preset DDDD 0 ~ 9999
W C DDDD 0 ~ 9999
W C_Curr DDDD 0 ~ 9999 Counter_Current
W C_Preset DDDD 0 ~ 9999
W CM DDDDD 0 ~ 65535
W EM DDDDD 0 ~ 65535
W FM DDDDD 0 ~ 65535
Note:
If Relay (bit) register is used, please place a zero at the end of the address.
For example, to read Relay (bit) 100, the address is written as “1000”.

158
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P OP-26486 9P D-Sub
D-Sub Female D-Sub Female Male
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P OP-26486 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P OP-26486 9P D-Sub
D-Sub Female Male
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND

Driver Version:
Version Date Description
V2.20 Jul/28/2009

159
PLC Connection Guide

Korenix 6550

Website: http://www.korenix.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Korenix 6550 Modbus protocol
PLC I/F Ethernet
Port no. 502
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B 1x DDDDD 1 ~ 65535
B 0x DDDDD 1 ~ 65535
B 3x_Bit DDDDDdd 100 ~ 6553515
B 4x_Bit DDDDDdd 100 ~ 6553515
B 6x_Bit DDDDDdd 100 ~ 6553515
W 3x DDDDD 1 ~ 65535
W 4x DDDDD 1 ~ 65535
W 5x DDDDD 1 ~ 65535
W 6x DDDDD 1 ~ 65535

160
PLC Connection Guide

Driver Version:
Version Date Description
V1.61 Apr/17/2009

161
PLC Connection Guide

KOYO CLICK
Supported Series: KOYO CLICK PLC series
Website: http://www.automationdirect.com

HMI Setting:
Parameters Recommended Options Notes
PLC type KOYO CLICK
PLC I/F RS232
Baud rate 38400 Com Port1 (fixed) Reference PLC Specification
Data bits 8 Com Port1 (fixed) Reference PLC Specification
Parity Odd Com Port1 (fixed) Reference PLC Specification
Stop bits 1 Com Port1 (fixed) Reference PLC Specification
PLC sta. no. 1 Com Port1 (fixed) Reference PLC Specification

Device Address:
Bit/Word Device type Format Range Memo
B X Ddd 001 ~ 816 Input Status (Read Only)
B Y Ddd 001 ~ 816 Output Status
B C DDDD 1 ~ 2000 Control Bit
B T DDD 1 ~ 500 Timer Status (Read Only)
B CT DDD 1 ~ 250 Counter Status (Read Only)
B SC DDDD 1 ~ 1000 System Control Bit (Read Only)
W DS DDDD 1 ~ 4500 Data Registers
W DD DDDD 1 ~ 1000 Data Registers (Double Word)
W DH DDD 1 ~ 500 Data Registers
W DF DDD 1 ~ 500 Data Registers (Double Word)
W XD D 0~8 Input Status Registers (Read Only)
W YD D 0~8 Output Status Registers
W TD DDD 1 ~ 500 Timer Current Values (Read Only)
Counter Current Values
W CTD DDD 1 ~ 250
(Double Word/Read Only)
System Data Registers
W SD DDDD 1 ~ 1000
(Read Only)
W TXT DDDD 1 ~ 1000 Text Data Registers

162
PLC Connection Guide

Wiring Diagram:
KOYO CLICK PLC Com Port:

The following represents the cable end connector.

Driver eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 6P RJ12 Male
D-Sub Female D-Sub Female
2 RX 8 RX 4 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 1 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 6P RJ12 Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 4 TXD
3 TX 4 TX 7 TX 3 RXD
5 GND 5 GND 5 GND 1 GND

163
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 6P RJ12 Male
D-Sub Female
9 RX 4 TXD
6 TX 3 RXD
5 GND 1 GND

Version:
Version Date Description
V1.50 Jun/22/2010

164
PLC Connection Guide

KOYO DIRECT
Supported Series: KOYO DirectLogic series PLC DL05, DL06, DL105, DL205, DL305, and
DL405 series.

Website: http://www.automationdirect.com

HMI Setting:
Parameters Recommended Options Notes
PLC type KOYO DIRECT
PLC I/F RS232 RS232, RS485
Baud rate 9600 9600, 19200, 38400
Data bits 8 7, 8
Parity Odd Even, Odd, None
Stop bits 1 1
PLC sta. no. 1 1-90

PLC Setting:
1. The PLC must not have a password.
2. PLC must be set for Full Duplex operation.
3. PLC must be set for No Hardware Handshaking.
4. The PLC must be set to use the ‘K’ Sequence Protocol.
5. Set the mode switch to the TERM mode.
6. When using the D4-440 CPU, the station number must be set to 1.

165
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
B X OOOO 0 ~ 4000 Input Bits
B Y OOOO 0 ~ 4000 Output Bits
B C OOOOO 0 ~ 10000 Control Relays
B T OOOO 0 ~ 1000 Timer Status Bits
B CT OOOO 0 ~ 1000 Counter Status Bits
B S OOOO 0 ~ 2000
B SP OOOO 0 ~ 2000
B GX OOOOO 0 ~ 10000
B GY OOOOO 0 ~ 10000
W V OOOOO 0 ~ 77777 V Memory
W Timer OOOO 0 ~ 1000
W Counter OOOO 0 ~ 1000

Wiring Diagram:
The following represents the cable end connector.
DL05/DL06/DL105/DL230/DL240/DL250/DL350/DL450 RS232 port
eMT3000 series
COM1 RS232 9P COM3 RS232 9P KOYO CLICK PLC
D-Sub Female D-Sub Female RS232 6P RJ12 Male
2 RX 8 RX 4 TX
3 TX 7 TX 3 RX
5 GND 5 GND 1 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P KOYO CLICK PLC
D-Sub Female D-Sub Female D-Sub Male RS232 6P RJ12 Male
2 RX 6 RX 8 RX 4 TX
3 TX 4 TX 7 TX 3 RX
5 GND 5 GND 5 GND 1 GND

166
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P KOYO CLICK PLC
D-Sub Female RS232 6P RJ12 Male
9 RX 4 TX
6 TX 3 RX
5 GND 1 GND

The following represents the cable end connector.

CPU unit: DL06/DL250 CPU Port2 RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 Port2 15P
D-Sub Female D-Sub Female D-Sub Male
2 RX 8 RX 2 TX
3 TX 7 TX 3 RX
5 GND 5 GND 7 GND
4 RTC
circuit
5 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 Port2 15P
D-Sub Female D-Sub Female D-Sub Male D-Sub Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 3 RX
5 GND 5 GND 5 GND 7 GND
4 RTC
circuit
5 CTS

167
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 Port2 15P
D-Sub Female D-Sub Male
9 RX 2 TX
6 TX 3 RX
5 GND 7 GND
4 RTC
circuit
5 CTS

The following represents the cable end connector.

CPU unit: DL06/DL250 CPU Port2 RS422
eMT3000 series
COM1 RS485 4W RS422 Port2 15P
9P D-Sub Male D-Sub Male
1 RX- 10 TX-
2 RX+ 9 TX+
3 TX- 6 RX-
4 TX+ 13 RX+
5 GND 7 GND
11 RTS+
Circuit
14 CTS+
12 RTS-
Circuit
15 CTS-

168
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 4W RS422 Port2 15P
9P D-Sub Male D-Sub Male
1 RX- 10 TX-
2 RX+ 9 TX+
3 TX- 6 RX-
4 TX+ 13 RX+
5 GND 7 GND
11 RTS+
Circuit
14 CTS+
12 RTS-
Circuit
15 CTS-

MT6050i/MT8050i
COM1 RS485 4W RS422 Port2 15P
9P D-Sub Female D-Sub Male
1 RX- 10 TX-
2 RX+ 9 TX+
3 TX- 6 RX-
4 TX+ 13 RX+
5 GND 7 GND
11 RTS+
Circuit
14 CTS+
12 RTS-
Circuit
15 CTS-

Note: DL06/DL250 CPU Port2 include RS232 and RS422

169
PLC Connection Guide
The following represents the cable end connector.
DL430/DL440/DL450 CPU unit Port0 RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 Port0 15P
D-Sub Female D-Sub Female D-Sub Male
2 RX 8 RX 2 TX
3 TX 7 TX 3 RX
5 GND 5 GND 13 GND
1 YOP
7 CTS circuit
2 YOM
4 ONLINE
circuit
14 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 Port0 15P
D-Sub Female D-Sub Female D-Sub Male D-Sub Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 3 RX
5 GND 5 GND 5 GND 13 GND
1 YOP
7 CTS circuit
2 YOM
4 ONLINE
circuit
14 GND

170
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 Port0 15P
D-Sub Female D-Sub Male
9 RX 2 TX
6 TX 3 RX
5 GND 13 GND
1 YOP
7 CTS circuit
2 YOM
4 ONLINE
circuit
14 GND

The following represents the cable end connector.

CPU unit: DL430/DL440/DL450 CPU unit Port1 & DL350 CPU unit Port2 RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 Port1 25P
D-Sub Female D-Sub Female D-Sub Male
2 RX RX 2 TX
3 TX 7 TX 3 RX
5 GND 5 GND 7 GND
4 RTC
Circuit
5 CTS

171
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 Port1 25P
D-Sub Female D-Sub Female D-Sub Male D-Sub Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 3 RX
5 GND 5 GND 5 GND 7 GND
4 RTC
Circuit
5 CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 Port1 25P
D-Sub Female D-Sub Male
9 RX 2 TX
6 TX 3 RX
5 GND 7 GND
4 RTC
Circuit
5 CTS

172
PLC Connection Guide
The following represents the cable end connector.
CPU unit: DL430/DL440/DL450 CPU unit Port1 & DL350 CPU unit Port2 RS422
eMT3000 series
COM1 RS485 4W RS422 Port 25P D-Sub
9P D-Sub Male Male
1 RX- 16 TX-
2 RX+ 14 TX+
3 TX- 10 RX-
4 TX+ 9 RX+
5 GND 7 GND
19 RTS+
Circuit
11 CTS+
18 RTS-
Circuit
23 CTS-

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS422 Port 25P D-Sub
9P D-Sub Male Male
1 RX- 16 TX-
2 RX+ 14 TX+
3 TX- 10 RX-
4 TX+ 9 RX+
5 GND 7 GND
19 RTS+
Circuit
11 CTS+
18 RTS-
Circuit
23 CTS-

173
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W RS422 Port 25P D-Sub
9P D-Sub Female Male
1 RX- 16 TX-
2 RX+ 14 TX+
3 TX- 10 RX-
4 TX+ 9 RX+
5 GND 7 GND
19 RTS+
Circuit
11 CTS+
18 RTS-
Circuit
23 CTS-

The following represents the cable end connector.

CPU unit: DL450 CPU unit Port3 RS422
eMT3000 series
COM1 RS485 4W RS422 Port3 25P
9P D-Sub Male D-Sub Male
1 RX- 13 TX-
2 RX+ 12 TX+
3 TX- 25 RX-
4 TX+ 24 RX+
5 GND 7 GND

174
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 4W RS422 Port3 25P
9P D-Sub Male D-Sub Male
1 RX- 13 TX-
2 RX+ 12 TX+
3 TX- 25 RX-
4 TX+ 24 RX+
5 GND 7 GND

MT6050i/MT8050i
COM1 RS485 4W RS422 Port3 25P
9P D-Sub Female D-Sub Male
1 RX- 13 TX-
2 RX+ 12 TX+
3 TX- 25 RX-
4 TX+ 24 RX+
5 GND 7 GND

The following represents the cable end connector.

Communication unit: DL205 series D2-DCM and DL405 series D4-DCM RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 Port 25P D-Sub
D-Sub Female D-Sub Female Male
2 RX 8 RX 2 TX
3 TX 7 TX 3 RX
5 GND 5 GND 7 GND
4 RTC
circuit
5 CTS

175
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 Port 25P D-Sub
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 3 RX
5 GND 5 GND 5 GND 7 GND
4 RTC
circuit
5 CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 Port 25P D-Sub
D-Sub Female Male
9 RX 2 TX
6 TX 3 RX
5 GND 7 GND
4 RTC
circuit
5 CTS

Driver Version:
Version Date Description
V1.30 Nov/08/2010

176
PLC Connection Guide

KOYO Ethernet
Supported Series: KOYO DirectLogic series, model H0-ECOM100, H2-ECOM100.

Website: http://www.automationdirect.com

HMI Setting:
Parameters Recommended Options Notes
PLC type KOYO Ethernet
PLC I/F Ethernet UDP/IP
Port no. 28784
PLC sta. no. No need to set station no. 0

Device Address:
Bit/Word Device type Format Range Memo
B GX OOOO 0 ~ 3777 Global I/O
B X OOOO 0 ~ 1777 Real Word Inputs
B SP OOOO 0 ~ 1777 Special Purpose Relays
B GY OOOO 0 ~ 3777 More Global I/O
B Y OOOO 0 ~ 1777 Real Word Outputs
B C OOOO 0 ~ 3777 Control Relays
B S OOOO 0 ~ 1777 Stage Status Bits
B T OOO 0 ~ 377 Timer Status Bits
B CT OOO 0 ~ 377 Counter Status Bits
W V OOOOO 0 ~ 41237 V-memory
W CCM_32 HHH 1 ~ 200 GX, X, SP
W CCM_33 HHH 1 ~ 340 GY,Y,C,S,Y,CT,V
W CCM_31 HHHH 1 ~ 42a0 V
EasyBuilder device address ranges may be different from PLC extended mode, please
refer to EasyBuilder address range as above.
ddd:Decimal, hhh:Hexadecimal, ooo:Octal

177
PLC Connection Guide

Driver Version:
Version Date Description
V1.10 Jul/03/2009

178
PLC Connection Guide

Lenze
Supported Series: PLC Model No.: 9300/8200 series, and EPL10200
Pass-through 2102IB fieldbus module: RS485 (LECOM B)

Website: http://www.lenze.de

HMI Setting:
Parameters Recommended Options Notes
PLC type Lenze
PLC I/F RS232
Baud rate 9600 9600, 19200
Data bits 7 7,8
Parity None Even, Odd, None
Stop bits 1 1, 2
PLC sta. no. 1 0-255

PLC Setting:
Communication mode Same as the MT500 setting

Device Address:
Bit/Word Device type Format Range Memo
Subcode not supported.
B CNB DDDDdd 0 ~ 999915 Can only read/write CNI
Word Type.
Subcode supported.
B CB DDDDddxx 0 ~ 81920015 Can only read/write CI
Word Type.
DDDDdd Subcode supported.
W CI 0 ~ 819200 Integer
DDDDdd 0 ~ 819200 Subcode supported.
W CD DWord
DDDDdd 0 ~ 819200 Subcode supported.
W CF DWord (float point)
Subcode not supported.
W CNI DDDD 0 ~ 9999 Integer
Subcode not supported.
W CND DDDD 0 ~ 9999 DWord
Subcode not supported.
W CNF DDDD 0 ~ 9999 DWord (float point)

179
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
Lenze 2102IB LECOM-B RS485 plug-in terminal 4-pole
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 72 T/R (A)
2 RX+ 9 Data+ 71 T/R (B)
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 72 T/R (A)
2 RX+ 9 Data+ 71 T/R (B)
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- 72 T/R (A)
2 RX+ 8 Data+ 71 T/R (B)
5 GND 5 GND

Driver Version:
Version Date Description
V1.20 Sep/6/2011
180
PLC Connection Guide

LingYan BMS

Website: http://www.lyeda.com/Project_file/bms01.htm

HMI Setting:
Parameters Recommended Options Notes
PLC type LingYan BMS
PLC I/F RS232
Baud rate 9600
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
W Battery_Unit D 0
W Insulator_Unit D 0
W Switch_Unit D 0

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 4P Terminal
D-Sub Female D-Sub Female
2 RX 8 RX 1 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 4 GND

181
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 4P Terminal
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 1 TXD
3 TX 4 TX 7 TX 3 RXD
5 GND 5 GND 5 GND 4 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 4P Terminal
D-Sub Female
9 RX 1 TXD
6 TX 3 RXD
5 GND 4 GND

Driver Version:
Version Date Description
V1.10 Nov/12/2009

182
PLC Connection Guide

LIYAN EX series
Supported Series: LIYAN PLC Ex/Ex1s/Ex1n/Ex2n series

Website: http://www.liyanplc.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi FX0s/FX0n/FX1s/FX1n/FX2
PLC I/F RS232 RS232
Baud rate 9600 9600~115200
Data bits 7 7,8
Parity Even Even, Odd, None
Stop bits 1 1,2
Must match the PLC port
PLC sta. no. 0 0-255
setting.

Device Address:
Bit/Word Device type Format Range Memo
B X ooo 0 ~ 377 Input Relay
B Y ooo 0 ~ 377 Output Relay
B M ddd 0 ~ 9999 Internal Bit Memory
B T ddd 0 ~ 255 Timer Bit Memory
B C ddd 0 ~ 255 Counter Bit Memory
W TV ddd 0 ~ 255 Timer Register
W CV ddd 0 ~ 199 Counter Register
W D ddd 0 ~ 9999 Data Register
W CV2 ddd 200 ~ 255 Counter Register (Double Word)
W SD ddd 8000 ~ 9999 Special Data Register

183
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 8P Mini-DIN: Ex, Ex1s, Ex1n, Ex2n series
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 8P Mini-DIN
D-Sub Female D-Sub Female Male
2 RX 8 RX 2 TXD
3 TX 7 TX 7 RXD
5 GND 5 GND 6 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 8P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 2 TXD
3 TX 4 TX 7 TX 7 RXD
5 GND 5 GND 5 GND 6 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 8P Mini-DIN
D-Sub Female Male
9 RX 2 TXD
6 TX 7 RXD
5 GND 6 GND

Driver Version:
Version Date Description
V1.20 Oct/26/2011
184
PLC Connection Guide

LoXin

Website: http://www.loxin-china.com

HMI Setting:
Parameters Recommended Options Notes
PLC type LoXin
PLC I/F RS-485 2W
Baud rate 9600
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
W Battery_Unit D 0
W Insulator_Unit D 0
W Switch_Unit D 0

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND

185
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Oct/16/2008

186
PLC Connection Guide

LS GLOFA Cnet
Supported Series: LS GLOFA GM6/GM7 CPU port. G7L-CUEB / G6L-CUEB / G4L-CUEA
/ G3L-CUEA Cnet module

Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS GLOFA Cnet
PLC I/F RS232 RS232/RS485 2W/4W
Baud rate 9600 9600~115200
Data bits 8 7, 8
Parity None Even, Odd, None
Stop bits 1 1
PLC sta. no. 0 0~31

PLC Setting:
Communication mode 9600,N,8,1 (default), Cnet protocol
Communication module Applicable mode: 1 dedicated communication

Device Address:
Bit/Word Device type Format Range Memo
B MX DDDDD 0 ~ 32767 Internal Relay
B IX ddDdd 0 ~ 63763 Input
B QX ddDdd 0 ~ 63763 Output
W MW DDDDD 0 ~ 32767 Data Register
DW MD DDDDD 0 ~ 16383 Double Word

187
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 9P D-Sub:
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 7 TXD
3 TX 7 TX 4 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 7 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 7 TXD
6 TX 4 RXD
5 GND 5 GND

188
PLC Connection Guide
The following represents the cable end connector.
9P D-Sub to 9P D-Sub: Communication Module (G7L-CUEB / G6L-CUEB / G4L-CUEA /
G3L-CUEA Cnet RS232)
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
1 CD
7 RTS circuit
8 CTS
4 DTR
circuit
6 DSR

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND
1 CD
7 RTS circuit
8 CTS
4 DTR
circuit
6 DSR

189
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
1 CD
7 RTS circuit
8 CTS
4 DTR
circuit
6 DSR

The following represents the cable end connector.

Communication Module (G7L-CUEC / G6L-CUEC / G4L-CUEA / G3L-CUEA Cnet RS422)
eMT3000 series
COM1 RS485 4W RS422 terminal
9P D-Sub Male
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

190
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 4W RS422 terminal
9P D-Sub Male
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

MT6050i/MT8050i
COM1 RS485 4W RS422 terminal
9P D-Sub Female
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

Driver Version:
Version Date Description
V1.80 Jun/08/2010

191
PLC Connection Guide

LS GLOFA FEnet (Ethernet)

Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS GLOFA FEnet (Ethernet)
PLC I/F Ethernet
Port no. 2004
PLC sta. no. 0 0~31

Device Address:
Bit/Word Device type Format Range Memo
B MX DDDDDD 0 ~ 131056 Internal Relay
B IX ddDdd 0 ~ 63763 Input
B QX ddDdd 0 ~ 63763 Output
W MW DDDD 0 ~ 8191 Data Register
DW MD DDDD 0 ~ 4095 Double Word

192
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 Apr/02/2009 Driver released.

193
PLC Connection Guide

LS GLOFA GM3467 (LOADER)

Supported Series: LS GLOFA series GM3, GM4, GM6, GM7 CPU port.

Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS GLOFA GM3467 (LOADER)
PLC I/F RS232
Baud rate 38400
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
B MX DDDDDD 0 ~ 524272
00.0.0 ~ 63.7.63
B IX ddDdd 0 ~ 63763
(dd.D.dd)
00.0.0 ~ 63.7.63
B QX ddDdd 0 ~ 63763
(dd.D.dd)
W IW HHH 0 ~ 273
W QW HHH 0 ~ 273
W MW DDDDD 0 ~ 32767
W MD DDDDD 0 ~ 16383

194
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P LS GLOFA series
D-Sub Female D-Sub Female RS232 9P D-Sub Male
2 RX 8 RX 3 TD
3 TX 7 TX 2 RD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P LS GLOFA series
D-Sub Female D-Sub Female D-Sub Male RS232 9P D-Sub Male
2 RX 6 RX 8 RX 3 TD
3 TX 4 TX 7 TX 2 RD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P LS GLOFA series
D-Sub Female RS232 9P D-Sub Male
9 RX 3 TD
6 TX 2 RD
5 GND 5 GND

Driver Version:
Version Date Description
V1.30 Mar/08/2010

195
PLC Connection Guide

LS MASTER-K Cnet
Supported Series: LS MASTER-K series: K80S, K200S, K300S, and K1000S

Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS MASTER-K Cnet
PLC I/F RS232 RS232/RS485
Baud rate 38400 9600, 19200, 38400
Data bits 8 8
Parity None Even, Odd, None
Stop bits 1 1
Must match the PLC port
PLC sta. no. 0 0-31
setting.

Online simulator YES

Device Address:
Bit/Word Device type Format Range Memo
B P DDDh 0 ~ 255f I/O Relay (P)
B K DDDh 0 ~ 255f Keep Relay (K)
B M DDDh 0 ~ 255f Auxiliary Relay (M)
B L DDDh 0 ~ 255f Link Relay (L)
B F DDDh 0 ~ 255f Special Relay (F)
B D_bit DDDDh 0 ~ 9999f D_bit
W TV DDD 0 ~ 255 Timer Present Value
W CV DDD 0 ~ 255 Counter Present Value
W D DDDD 0 ~ 9999 Data Register (D)
W M_word DDD 0 ~ 255 Word type for M
W L_word DDD 0 ~ 255 Word type for L
W F_word DDD 0 ~ 255 Word type for F

196
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P CPU Port Cnet I/F
D-Sub Female D-Sub Female RS232 9P D-Sub Male
2 RX 8 RX 7 TX
3 TX 7 TX 4 RX
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P CPU Port Cnet I/F
D-Sub Female D-Sub Female D-Sub Male RS232 9P D-Sub Male
2 RX 6 RX 8 RX 7 TX
3 TX 4 TX 7 TX 4 RX
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P CPU Port Cnet I/F
D-Sub Female RS232 9P D-Sub Male
9 RX 7 TX
6 TX 4 RX
5 GND 5 GND

If connected with Cnet module, please refer to Cnet module document.

Driver Version:
Version Date Description
V1.00 Apr/19/2010 Driver released.
V1.10 May/11/2011 Added registers: D_bit, M_word, F_word, L_word

197
PLC Connection Guide

LS MASTER-K CPU Direct

Supported Series: LS MASTER-K series: K80S, K120S, K200S, K300S, K1000S, K7M.

Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LG MASTER-K CPU Direct
PLC I/F RS232 RS232/RS485
Baud rate 38400 9600, 19200, 38400
Data bits 8 8
Parity None Even, Odd, None
Stop bits 1 1
Must match the PLC port
PLC sta. no. 0 0-31
setting.

Online simulator YES

198
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TX
3 TX 7 TX 2 RX
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TX
3 TX 4 TX 7 TX 2 RX
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TX
6 TX 2 RX
5 GND 5 GND

Driver Version:
Version Date Description
V1.20 May/11/2011 Added registers: D_bit, M_word, F_word, L_word

199
PLC Connection Guide

LS MASTER-K MODBUS RTU

Supported Series: LS MASTER-K MODBUS RTU

Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS MASTER-K MODBUS RTU
PLC I/F RS485 2W
Baud rate 9600
Data bits 8 8
Parity Even Even
Stop bits 1 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
B P DDDDh 0 ~ 9999f I/O Relay (P)
B M DDDDh 0 ~ 9999f Auxiliary Relay (M)
B L DDDDh 0 ~ 9999f Link Relay (L)
B K DDDDh 0 ~ 9999f Keep Relay (K)
B F DDDDh 0 ~ 9999f Special Relay (F)
B D_bit DDDDh 0 ~ 9999f
W T DDDD 0 ~ 9999 Timer (T)
W C DDDD 0 ~ 9999 Counter (C)
W S DDDD 0 ~ 9999
W D DDDD 0 ~ 9999 Data Register (D)
W T_double DDDD 0 ~ 9999
W C_double DDDD 0 ~ 9999
W S_double DDDD 0 ~ 9999
W D_double DDDD 0 ~ 9999
W F_word DDDD 0 ~ 9999
W L_word DDDD 0 ~ 9999
W M_word DDDD 0 ~ 9999

200
PLC Connection Guide

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TX
3 TX 4 TX 7 TX 2 RX
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TX
6 TX 2 RX
5 GND 5 GND

Driver Version:
Version Date Description
V1.10 May/11/2011 Added registers: D_bit, M_word, F_word, L_word

201
PLC Connection Guide

LS MASTER-K10S1
Supported Series: LS MASTER-K10S1

Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS MASTER-K10S1
PLC I/F RS232 RS232/RS485
Baud rate 9600
Data bits 8 8
Parity None None
Stop bits 1 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B P DDDh 0 ~ 255f I/O Relay (P)
B K DDDh 0 ~ 255f Keep Relay (K)
B M DDDh 0 ~ 255f Auxiliary Relay (M)
B L DDDh 0 ~ 255f Link Relay (L)
B F DDDh 0 ~ 255f Special Relay (F)
B T DDD 0 ~ 255 Timer (T)
B C DDD 0 ~ 255 Counter (C)
W TV DDD 0 ~ 255 Timer Present Value
W CV DDD 0 ~ 255 Counter Present Value
W D DDDD 0 ~ 9999 Data Register (D)

202
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
Driver eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TX
3 TX 7 TX 2 RX
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TX
3 TX 4 TX 7 TX 2 RX
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TX
6 TX 2 RX
5 GND 5 GND

Version:
Version Date Description
V1.00 Sep/08/2009 Driver released.

203
PLC Connection Guide

LS XGB Cnet
Supported Series: LS XGB/XGT Series
Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS XGB Cnet
PLC I/F RS232 RS232/RS485
Baud rate 115200 9600~115200
Data bits 8 7, 8
Parity None Even, Odd, None
Stop bits 1 1
PLC sta. no. 1 0-31

204
PLC Connection Guide
Bit/Word Device type Format Range Memo
W S DDDDD 0 ~ 12799 Relay for step control
W D DDDDD 0 ~ 32767 Data register_5120 words
W U DH.DD 0.00 ~ 7f.31 Analog data register_256 words
Communication data
W N DDDDD 0 ~ 21503
register_3,936 words
W Z DDD 0 ~ 127 Index register_128 words
Timer current value
W T DDDD 0 ~ 2047
register_256 words
Counter current value
W C DDDD 0 ~ 2047
register_256 words

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 6P Mini-DIN
D-Sub Female D-Sub Female Male
2 RX 8 RX 6 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 3 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 6P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 6 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 3 GND

205
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 6P Mini-DIN
D-Sub Female Male
9 RX 6 TXD
6 TX 2 RXD
5 GND 3 GND

Driver Version:
Version Date Description
V1.50 Mar/07/2011 Added registers: P_Bit, M_Bit, L_Bit, K_Bit…etc

206
PLC Connection Guide

LS XGB FEnet (Ethernet)

Supported Series: LS XGB/XGT with XBL-EMTA
Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS XGB FEnet (Ethernet)
PLC I/F Ethernet
Port no. 2004
PLC sta. no. 0 0~255

PLC Setting:
Communication mode FEnet Potocol

Device Address:
Bit/Word Device type Format Range Memo
B P_Bit DDDDh 0 ~ 2047f I/O device Bit
B M_Bit DDDDh 0 ~ 2047f Internal device Bit
B L_Bit DDDDDh 0 ~ 11263f Communication device Bit
B K_Bit DDDDh 0 ~ 2559f Preservation device Bit
Special device Bit( write available
B F_Bit DDDDh 0 ~ 2047f
from 1025)
B S_Bit DDDh 0 ~ 127f Relay for step control Bit
B D_Bit DDDDDh 0 ~ 32767f Data register_Bit expression
B U_Bit DH.DDh 0.000 ~ 7f.31f XGK-CPUE : hh(0~1f)
B T_Bit DDDD 0 ~ 2047 Timer device Bit
B C_Bit DDDD 0 ~ 2047 Counter device Bit
W P DDDD 0 ~ 2047 I/O device_2,048 points
W M DDDD 0 ~ 2047 Internal device_4,096 points
Communication device_20,480
W L DDDDD 0 ~ 11263
points
W K DDDD 0 ~ 2559 Preservation device_4,096 points
W F DDDD 0 ~ 2047 Special device_4,096 point
W S DDDDD 0 ~ 12799 Relay for step control
207
PLC Connection Guide
Bit/Word Device type Format Range Memo
W D DDDDD 0 ~ 32767 Data register_5120 words
W U DH.DD 0.00 ~ 7f.31 Analog data register_256 words
Communication data
W N DDDDD 0 ~ 21503
register_3,936 words
W Z DDD 0 ~ 127 Index register_128 words
Timer current value register_256
W T DDDD 0 ~ 2047
words
Counter current value
W C DDDD 0 ~ 2047
register_256 words

208
PLC Connection Guide
Through a hub:
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 1 TX+
2 TX- Orange 2 TX-
3 RX+ White/Green 3 RX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 6 RX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Driver Version:
Version Date Description
V1.50 Aug/16/2011 Added registers: P_Bit, M_Bit, L_Bit, K_Bit…etc

209
PLC Connection Guide

LS XGI Cnet
Supported Series: LS XGI series communication module XGL-CH2A
Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS XGI Cnet
PLC I/F RS232 RS232/RS485 4W
Baud rate 115200 9600~115200
Data bits 8 7, 8
Parity None Even, Odd, None
Stop bits 1 1
PLC sta. no. 0 0~255

Device Address:
Bit/Word Device type Format Range Memo
B A_Bit DDDDDDh 0 ~ 262143f
B I_Bit DDD.DD.Dh 0 ~ 127.15.3f
B Q_Bit DDD.DD.Dh 0 ~ 127.15.3f
B M_Bit DDDDDDh 0 ~ 131071f
B R_Bit DDDDDh 0 ~ 32767f
B W_Bit DDDDDh 0 ~ 65535f
B F_Bit DDDDh 0 ~ 2047f
B K_Bit DDDDh 0 ~ 8399f
B L_Bit DDDDDh 0 ~ 11263f
B N_Bit DDDDDh 0 ~ 25087f
B U_Bit DD.DD.DDh 0 ~ 31.15.31f
W A DDDDDD 0 ~ 262143
W I DDD.DD.D 0 ~ 127.15.3
W Q DDD.DD.D 0 ~ 127.15.3
W M DDDDDD 0 ~ 131071
W R DDDDD 0 ~ 32767
W W DDDDD 0 ~ 65535
W F DDDD 0 ~ 2047
W K DDDD 0 ~ 8399
210
PLC Connection Guide
Bit/Word Device type Format Range Memo
W L DDDDD 0 ~ 11263
W N DDDDD 0 ~ 25087
W U DD.DD.DD 0 ~ 31.15.31

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 9P D-Sub:
eMT3000 series
COM1 RS232 9P COM3 RS232 9P XGL-CH2A CH1 RS232
D-Sub Female D-Sub Female 9P D-Sub Male
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P XGL-CH2A CH1 RS232
D-Sub Female D-Sub Female D-Sub Male 9P D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P XGL-CH2A CH1 RS232
D-Sub Female 9P D-Sub Male
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND

211
PLC Connection Guide
The following represents the cable end connector.
9P D-Sub to Terminals:
eMT3000 series
COM1 RS485 4W XGL-CH2A CH2 5P
9P D-Sub Male Terminal
1 RX- TXD-
2 RX+ TXD+
3 TX- RXD-
4 TX+ RXD+
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W XGL-CH2A CH2 5P
9P D-Sub Male Terminal
1 RX- TXD-
2 RX+ TXD+
3 TX- RXD-
4 TX+ RXD+
5 GND GND

MT6050i/MT8050i
COM1 RS485 4W XGL-CH2A CH2 5P
9P D-Sub Female Terminal
1 RX- TXD-
2 RX+ TXD+
3 TX- RXD-
4 TX+ RXD+
5 GND GND

212
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 May/23/2012 Driver released

213
PLC Connection Guide

LS XGI CPU DIRECT

Supported Series: LS XGI CPU RS232 port.
Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS XGI CPU DIRECT
PLC I/F RS232 RS232
Baud rate 115200 9600~115200
Data bits 8 7, 8
Parity None Even, Odd, None
Stop bits 1 1
PLC sta. no. 1 1

Device Address:
Bit/Word Device type Format Range Memo
B A_Bit DDDDDDh 0 ~ 262143f
B I_Bit DDD.DD.Dh 0 ~ 127.15.3f
B Q_Bit DDD.DD.Dh 0 ~ 127.15.3f
B M_Bit DDDDDDh 0 ~ 131071f
B R_Bit DDDDDh 0 ~ 32767f
B W_Bit DDDDDh 0 ~ 65535f
B F_Bit DDDDh 0 ~ 2047f
B K_Bit DDDDh 0 ~ 8399f
B L_Bit DDDDDh 0 ~ 11263f
B N_Bit DDDDDh 0 ~ 25087f
B U_Bit DD.DD.DDh 0 ~ 31.15.31f
W A DDDDDD 0 ~ 262143
W I DDD.DD.D 0 ~ 127.15.3
W Q DDD.DD.D 0 ~ 127.15.3
W M DDDDDD 0 ~ 131071
W R DDDDD 0 ~ 32767
W W DDDDD 0 ~ 65535
W F DDDD 0 ~ 2047
214
PLC Connection Guide
Bit/Word Device type Format Range Memo
W K DDDD 0 ~ 8399
W L DDDDD 0 ~ 11263
W N DDDDD 0 ~ 25087
W U DD.DD.DD 0 ~ 31.15.31

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND

215
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 May/17/2012 Driver released.

216
PLC Connection Guide

LS XGI FEnet (Ethernet)

Supported Series: LS XGI series XGL-EFMT Ethernet module.
Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS XGI FEnet (Ethernet)
PLC I/F Ethernet
Port no. 2004
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B A_Bit DDDDDDh 0 ~ 262143f
B I_Bit DDD.DD.Dh 0 ~ 127.15.3f
B Q_Bit DDD.DD.Dh 0 ~ 127.15.3f
B M_Bit DDDDDDh 0 ~ 131071f
B R_Bit DDDDDh 0 ~ 32767f
B W_Bit DDDDDh 0 ~ 65535f
B F_Bit DDDDh 0 ~ 2047f
B K_Bit DDDDh 0 ~ 8399f
B L_Bit DDDDDh 0 ~ 11263f
B N_Bit DDDDDh 0 ~ 25087f
B U_Bit DD.DD.DDh 0 ~ 31.15.31f
W A DDDDDD 0 ~ 262143
W I DDD.DD.D 0 ~ 127.15.3
W Q DDD.DD.D 0 ~ 127.15.3
W M DDDDDD 0 ~ 131071
W R DDDDD 0 ~ 32767
W W DDDDD 0 ~ 65535
W F DDDD 0 ~ 2047
W K DDDD 0 ~ 8399
W L DDDDD 0 ~ 11263
W N DDDDD 0 ~ 25087
W U DD.DD.DD 0 ~ 31.15.31
217
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 May/21/2012 Driver released.

218
PLC Connection Guide

LS XGK Cnet
Supported Series: LS XGT series communication module XGL-CH2A
Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS XGK Cnet
PLC I/F RS232 RS232/RS485 4W
Baud rate 115200 9600~115200
Data bits 8 7, 8
Parity None Even, Odd, None
Stop bits 1 1
PLC sta. no. 1 0~32

219
PLC Connection Guide
Bit/Word Device type Format Range Memo
W S DDDDD 0 ~ 127 Relay for step control
W D DDDDD 0 ~ 32767 Data register
Analog data register
W U DH.DD 0.00 ~ 3f.31
XGK-CPUE : hh(0~1f)
W N DDDDD 0 ~ 21503 Communication data register
W Z DDD 0 ~ 127 Index register_128 words
W T DDDD 0 ~ 2047 Timer current value register
Counter current value
W C DDDD 0 ~ 2047
register
W R DDDDD 0 ~ 32767
W ZR DDDDD 0 ~ 32767

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P XGL-CH2A CH1 RS232
D-Sub Female D-Sub Female D-Sub Male 9P D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND

220
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P XGL-CH2A CH1 RS232
D-Sub Female 9P D-Sub Male
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND

The following represents the cable end connector.

9P D-Sub to Terminals:
eMT3000 series
COM1 RS485 4W XGL-CH2A CH2 5P
9P D-Sub Male Terminal
1 RX- TXD-
2 RX+ TXD+
3 TX- RXD-
4 TX+ RXD+
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W XGL-CH2A CH2 5P
9P D-Sub Male Terminal
1 RX- TXD-
2 RX+ TXD+
3 TX- RXD-
4 TX+ RXD+
5 GND GND

221
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W XGL-CH2A CH2 5P
9P D-Sub Female Terminal
1 RX- TXD-
2 RX+ TXD+
3 TX- RXD-
4 TX+ RXD+
5 GND GND

Driver Version:
Version Date Description
V1.30 Feb /25/2011 Added registers: P_Bit, M_Bit, L_Bit, K_Bit…etc
V1.40 Jun/20/2012 Change the way to read/write S_Bit.

222
PLC Connection Guide

LS XGK FEnet (Ethernet)

Supported Series: LS XGT series XGL-EFMT Ethernet module.

Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS XGK FEnet (Ethernet)
PLC I/F Ethernet
Port no. 2004
PLC sta. no. 0

B S_Bit DDDDD 0 ~ 12799 Relay for step control Bit

Data register_Bit expression
B D_Bit DDDDDh 0 ~ 32767f
(D0000.0)
B U_Bit DH.DDh 0.000 ~ 3f.31f XGK-CPUE : hh(0~1f)
B T_Bit DDDD 0 ~ 2047 Timer device Bit
B C_Bit DDDD 0 ~ 2047 Counter device Bit
W P DDDD 0 ~ 2047 I/O device
W M DDDD 0 ~ 2047 Internal device
W L DDDDD 0 ~ 11263 Communication device
W K DDDD 0 ~ 2559 Preservation device
Special device( write available
W F DDDD 0 ~ 2047
from 1025)
W S DDDDD 0 ~ 127 Relay for step control
W D DDDDD 0 ~ 32767 Data register

223
PLC Connection Guide
Bit/Word Device type Format Range Memo
Analog data register XGK-CPUE :
W U DH.DD 0.00 ~ 3f.31
hh(0~1f)
W N DDDDD 0 ~ 21503 Communication data register
W Z DDD 0 ~ 127 Index register_128 words
W T DDDD 0 ~ 2047 Timer current value register
W C DDDD 0 ~ 2047 Counter current value register
W R DDDDD 0 ~ 32767
W ZR DDDDD 0 ~ 32767

224
PLC Connection Guide

Driver Version:
Version Date Description
V1.30 Mar/10/2011 Added registers: P_Bit, M_Bit, L_Bit, K_Bit…etc
V1.40 Jun/19/2012 Change the way to read/write S_Bit.

225
PLC Connection Guide

LS XGT/XGK CPU DIRECT

Supported Series: LS XGT/XGK CPU RS232 port.
Website: http://www.lgis.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type LS XGT/XGK CPU DIRECT
PLC I/F RS232 RS232
Baud rate 115200 9600~115200
Data bits 8 7, 8
Parity None Even, Odd, None
Stop bits 1 1
PLC sta. no. 1 1

226
PLC Connection Guide
Bit/Word Device type Format Range Memo
W S DDDDD 0 ~ 127 Relay for step control
W D DDDDD 0 ~ 32767 Data register
Analog data register
W U DH.DD 0.00 ~ 3f.31
XGK-CPUE : hh(0~1f)
W N DDDDD 0 ~ 21503 Communication data register
W Z DDD 0 ~ 127 Index register_128 words
W T DDDD 0 ~ 2047 Timer current value register
W C DDDD 0 ~ 2047 Counter current value
W R DDDDD 0 ~ 32767 register
W ZR DDDDD 0 ~ 32767
W TS DDDD 0 ~ 2047 Setup value
W CS DDDD 0 ~ 2047 Setup value

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND

227
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND

Driver Version:
Version Date Description
V1.40 Mar/10/2011 Added registers: P_Bit, M_Bit, L_Bit, K_Bit…etc
V1.60 Jun/18/2012 Change the way to read/write S_Bit.

228
PLC Connection Guide

LS Mecapion Metronix AnyPack

HMI Setting:
Parameters Recommended Options Notes
PLC type LS Mecapion Metronix AnyPack
PLC I/F RS232
Baud rate 9600
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device Type Format Range Memo
B MX_L16bit DDDDDdd 0 ~ 9999915 MD Low 16bit
B MX_H16bit DDDDDdd 0 ~ 9999915 MD High 16bit
DW MD DDDD 0 ~ 9999

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P PLC RS232 Terminal
D-Sub Female D-Sub Female
2 RX 8 RX 6 TX
3 TX 7 TX 5 RX
5 GND 5 GND 11 GND
circuit
12 GND

229
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P PLC RS232 Terminal
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 6 TX
3 TX 4 TX 7 TX 5 RX
5 GND 5 GND 5 GND 11 GND
circuit
12 GND

MT6050i/MT8050i
COM1 RS232 9P PLC RS232 Terminal
D-Sub Female
9 RX 6 TX
6 TX 5 RX
5 GND 11 GND
circuit
12 GND

Driver Version:
Version Date Description
V1.00 Jul/1/2008

230
PLC Connection Guide

Master-Slave Server

For more information, please refer to User’s Manual CH28.

HMI Setting:
Parameters Recommended Options Notes
PLC type Master-Slave Server
PLC I/F RS232 RS232/RS485
Baud rate 115200 9600~115200
Data bits 8 7,8
Parity Even None,Even,Odd,Mark,Space
Stop bits 1 1,2
HMI sta. no. 0
PLC sta. no. 0

FOR MT500 HMI Setting:

Parameters Recommended Options Notes
PLC type Master (Master-Slave Protocol)
PLC I/F RS232
Baud rate 115200 38400, 115200
Data bits 8
Parity Even
Stop bits 1
HMI sta. no. 0
PLC sta. no. 0
Parameter 1 MT500 PLC ID Use PLCAddressView.exe to find PLC ID.

231
PLC Connection Guide
To connect HMI with MT500, MT500 has to be set as [Slave].

PLC Setting:
Communication mode MT500 Multiple HMI set Slave.

232
PLC Connection Guide

Device Address:
Bit/Word MT500 MT8000 Range Memo
ddd: 0 ~ 4095
B Ms_RB RW_Bit
(h): 0 ~ f
B Ms_LB LB dddd:0 ~ 9999
W Ms_RW RW ddd:0 ~ 65535
W Ms_LW LW ddd:0 ~ 9999

Driver Version:
Version Date Description
V1.00 Dec/30/2008 Driver released.

233
PLC Connection Guide

Memory Map
Memory Map protocol is similar to IBM 3764R communication protocol. EasyBuilder
reserves 512 words of data memory to use with this protocol. EasyBuilder must update the
values in these words. EasyBuilder uses these words to display data and control parts
status on screen. When touch actions are taken, data is sent to the others once, and then
update the memory in it. The HMI should always update the data memory.

HMI Setting:
Parameters Recommended Options Notes
PLC type Memory Map
RS232, RS485
PLC I/F RS232 RS232 default
4W, 2W
Baud rate 115200 9600~115200
Data bits 8
Parity Even Even, Odd, None
Stop bits 1

Device Address:
Bit/Word Device type Format Range Memo
B MB DDDDh 0 ~ 4095f
W MW DDDD 0 ~ 9999
MB and MW share the same data storage.
MW 0 = MB 00000 ~ MB 0000f, MW 1 = MB 00010 ~ MB 0001f

234
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P HMI COM1 RS232 9P
D-Sub Female D-Sub Female D-Sub Female
2 RX 8 RX 3 TX
3 TX 7 TX 2 RX
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P HMI COM1 RS232 9P
D-Sub Female D-Sub Female D-Sub Male D-Sub Female
2 RX 6 RX 8 RX 3 TX
3 TX 4 TX 7 TX 2 RX
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P HMI COM1 RS232 9P
D-Sub Female D-Sub Female
9 RX 3 TX
6 TX 2 RX
5 GND 5 GND

235
PLC Connection Guide
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W HMI COM1 RS485 2W
9P D-Sub Male 9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 1 RX-
2 RX+ 9 Data+ 2 RX+
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W HMI COM1 RS485 2W
9P D-Sub Male 9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 1 RX-
2 RX+ 9 Data+ 2 RX+
5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W HMI COM1 RS485 2W
9P D-Sub Female 9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- 1 RX-
2 RX+ 8 Data+ 2 RX+
5 GND 5 GND 5 GND

236
PLC Connection Guide
The following represents the cable end connector.
eMT3000 series
COM1 RS485 4W HMI COM1 RS485 4W
9P D-Sub Male 9P D-Sub Male
1 RX- 3 TX-
2 RX+ 4 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W HMI COM1 RS485 4W
9P D-Sub Male 9P D-Sub Male
1 RX- 3 TX-
2 RX+ 4 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 5 GND

237
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W HMI COM1 RS485 4W
9P D-Sub Female 9P D-Sub Female
1 RX- 3 TX-
2 RX+ 4 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 5 GND

Note:
For Memory map information, please refer to User’s Manual “Chapter 31 Memory Map
Communication”.

Driver Version:
Version Date Description
V1.00 Mar/19/2009 Driver released.

238
PLC Connection Guide

MIKOM MX Series PLC

Support series: MIKOM MX series PLC
Web: http://www.mikom.com.cn/

HMI Setting:
Parameters Recommended Options Notes
PLC type MIKOM MX Series PLC
PLC I/F RS232 RS232/485/Ethernet
Baud rate 19200 9600~115200
Data bits Even None,Even,Odd
Parity 8 8
Stop bits 1 1,2
PLC sta. no. 1 0~31

Online simulator YES

PLC Setting:
PORT 0(RS232 Setting)

239
PLC Connection Guide
PORT 1(RS485 Setting)

Device Address:
Bit/Word Device type Format Range Memo
B Y DDD 0~777 Output Relay
B X DDD 0~777 Input Relay
B M DDDD 0~4095 Auxiliary Relay
B SM DDD 0-511 Special Auxiliary Relay
B S DDDD 0~1535 Step Relay
B T DDD 0~511 Timer Relay
B C DDD 0~511 Counter Relay
W D DDDDD 0~32767 Data Register
W SD DDD 0~511 Special Data Register
W Z DDD 0~255 Indexed Addressing Register
W T DDD 0~511 Timer
W C DDD 0~199 Counter
W U0 DDD 0~199 Special Module Register
W U1 DDD 0~199 Special Module Register
W U2 DDD 0~199 Special Module Register
W U3 DDD 0~199 Special Module Register
W U4 DDD 0~199 Special Module Register
W U5 DDD 0~199 Special Module Register
W U6 DDD 0~199 Special Module Register
W U7 DDD 0~199 Special Module Register
DW C-32bit DDD 200~511 32 Bit Counter

240
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 8P Mini-DIN
D-Sub Female D-Sub Female Male
2 RX 8 RX 3 TX
3 TX 7 TX 2 RX
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 8P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 3 TX
3 TX 4 TX 7 TX 2 RX
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 8P Mini-DIN
D-Sub Female Male
9 RX 3 TX
6 TX 2 RX
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 May/3/2012 Driver released.

241
PLC Connection Guide

Mitsubishi A1S
Supported Series: Mitsubishi A1S

Website: http://www.mitsubishi-automation.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi A1S
PLC I/F RS232
Baud rate 9600
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B X HHHH 0 ~ ffff Input Relay
B Y HHHH 0 ~ ffff Output Relay
B M DDDDD 0 ~ 65535 Auxiliary Relay
B B HHHH 0 ~ ffff
B F DDDDD 0 ~ 65535
W TV DDDDD 0 ~ 65535 Timer Memory
W CV DDDDD 0 ~ 65535 Counter Memory
W D DDDDD 0 ~ 65535 Data Register
W W HHHH 0 ~ ffff
W R DDDDD 0 ~ 65535

242
PLC Connection Guide

Wiring Diagram:
Use the RS422 to RS232 PLC programming cable (shown as follows)

MITSUBISHI AnS CPU

The following represents the cable end connector.

eMT3000 series
COM1 RS232 9P Mitsubishi RS422 25P
PLC Programming Converter
D-Sub Female D-Sub Male
2 RX TX TX+ 2 RX+
3 TX RX RX+ 3 TX+
5 GND GND DTR+ 4 DSR+
7 RTS CTS GND 7 GND
8 CTS RTS TX- 15 RX-
RX- 16 TX-
DTR- 17 DSR-

243
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P Mitsubishi RS422 25P
PLC Programming Converter
D-Sub Female D-Sub Male
2 RX TX TX+ 2 RX+
3 TX RX RX+ 3 TX+
5 GND GND DTR+ 4 DSR+
7 RTS CTS GND 7 GND
8 CTS RTS TX- 15 RX-
RX- 16 TX-
DTR- 17 DSR-

Driver Version:
Version Date Description
V1.00 Sep/18/2009 Driver released.

244
PLC Connection Guide

Mitsubishi A2A/A2U/A2AS/A2USH
Supported Series: Mitsubishi A2A,A2U,A2AS,A2USH

Website: http://www.mitsubishi-automation.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi A2A/A2U/A2AS/A2USH
PLC I/F RS232
Baud rate 9600
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B X HHHH 0 ~ 270f Input Relay
B Y HHHH 0 ~ 270f Output Relay
B M DDDD 0 ~ 9999 Auxiliary Relay
B B HHHH 0 ~ ffff
B F DDDDD 0 ~ 65535
W TV DDD 0 ~ 255 Timer Memory
W CV DDD 0 ~ 255 Counter Memory
W D DDDD 0 ~ 9999 Data Register
W W HHHH 0 ~ ffff
W R DDDDD 0 ~ 65535

245
PLC Connection Guide

Wiring Diagram:
Use the RS422 to RS232 PLC programming cable (shown as follows)

MITSUBISHI AnS CPU

The following represents the cable end connector.

246
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P Mitsubishi RS422 25P
PLC Programming Converter
D-Sub Female D-Sub Male
2 RX TX TX+ 2 RX+
3 TX RX RX+ 3 TX+
5 GND GND DTR+ 4 DSR+
7 RTS CTS GND 7 GND
8 CTS RTS TX- 15 RX-
RX- 16 TX-
DTR- 17 DSR-

Driver Version:
Version Date Description
V1.00 Aug/12/2009 Driver released.

247
PLC Connection Guide

Mitsubishi A2N/A3A/A3N/A1SH/A2SH
Supported Series: Mitsubishi A2N,A3A,A3N,A1SH,A2SH

Website: http://www.mitsubishi-automation.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi A2N/A3A/A3N/A1SH/A2SH
PLC I/F RS232
Baud rate 9600
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. 0

Note: This driver is not available for On-line Simulation.

248
PLC Connection Guide

Wiring Diagram:
Use the RS422 to RS232 PLC programming cable (shown as follows)

MITSUBISHI AnS CPU

The following represents the cable end connector.

249
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P Mitsubishi RS422 25P
PLC Programming Converter
D-Sub Female D-Sub Male
2 RX TX TX+ 2 RX+
3 TX RX RX+ 3 TX+
5 GND GND DTR+ 4 DSR+
7 RTS CTS GND 7 GND
8 CTS RTS TX- 15 RX-
RX- 16 TX-
DTR- 17 DSR-

Driver Version:
Version Date Description
V1.00 Oct/20/2009 Driver released.

250
PLC Connection Guide

Mitsubishi A2US
Supported Series: Mitsubishi A2US

Website: http://www.mitsubishi-automation.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi A2US
PLC I/F RS232
Baud rate 9600
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B X HHHH 0 ~ 270f Input Relay
B Y HHHH 0 ~ 270f Output Relay
B M DDDD 0 ~ 9999 Auxiliary Relay
W TV DDD 0 ~ 255 Timer Memory
W CV DDD 0 ~ 255 Counter Memory
W D DDDD 0 ~ 9999 Data Register

251
PLC Connection Guide

Wiring Diagram:
Use the RS422 to RS232 PLC programming cable (shown as follows)

MITSUBISHI AnS CPU

The following represents the cable end connector.

252
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P Mitsubishi RS422 25P
PLC Programming Converter
D-Sub Female D-Sub Male
2 RX TX TX+ 2 RX+
3 TX RX RX+ 3 TX+
5 GND GND DTR+ 4 DSR+
7 RTS CTS GND 7 GND
8 CTS RTS TX- 15 RX-
RX- 16 TX-
DTR- 17 DSR-

Driver Version:
Version Date Description
V1.00 Mar/20/2009 Driver released.

253
PLC Connection Guide

Mitsubishi AJ71
Supported Series: Mitsubishi A series PLC with AJ71C24 communication module using
the Computer Link protocol.

Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
Mitsubishi AJ71
(AnA/AnU CPU),
PLC type Mitsubishi AJ71
Mitsubishi AJ71
(Format 4)
PLC I/F RS485 4W RS485 4W, RS232
Baud rate 19200 9600, 19200
Data bits 8 8
Parity Even Even, Odd, None
Stop bits 1 1
PLC sta. no. 0

PLC Setting:
Communication mode Computer Link protocol 9600, Even, 8, 1 (default)
Mode setting switch Format 1
Parity check Enable
Sum check Enable

254
PLC Connection Guide
Bit/Word Device type Format Range Memo
B F DDDDD 0 ~ 65535
W TV DDDDD 0 ~ 65535 Timer Preset Value
W CV DDDDD 0 ~ 65535 Counter Preset Value
W D DDDDD 0 ~ 65535 Data Registers
W W HHHH 0 ~ ffff
W R DDDDD 0 ~ 65535

Wiring Diagram:
The following represents the cable end connector.
AJ71C24 RS422
eMT3000 series
COM1 RS485 4W AJ71C24 RS422
9P D-Sub Male Terminal
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W AJ71C24 RS422
9P D-Sub Male Terminal
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

255
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W AJ71C24 RS422
9P D-Sub Female Terminal
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

The following represents the cable end connector.

A1SJ71UC24-R2
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
1 DCD
4 DTR circuit
6 DSR
7 RTS
circuit
8 CTS

256
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND
1 DCD
4 DTR circuit
6 DSR
7 RTS
circuit
8 CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
1 DCD
4 DTR circuit
6 DSR
7 RTS
circuit
8 CTS

Driver Version:
Version Date Description
V1.50 Mar/11/2010

257
PLC Connection Guide

Mitsubishi AJ71 (AnA/AnU CPU)

Supported Series: Mitsubishi AJ71 (AnA/AnU CPU)
Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi AJ71 (AnA/AnU CPU)
PLC I/F RS485 4W RS485 4W, RS232
Baud rate 19200 9600, 19200
Data bits 8 8
Parity Even Even, Odd, None
Stop bits 1 1
PLC sta. no. 0

PLC Setting:
Communication mode Computer Link protocol 9600, Even, 8, 1 (default)
Mode setting switch Format 1
Parity check Enable
Sum check Enable

258
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 4W RS422 Terminal
9P D-Sub Male
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS422 Terminal
9P D-Sub Male
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

MT6050i/MT8050i
COM1 RS485 4W RS422 Terminal
9P D-Sub Female
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

259
PLC Connection Guide
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
1 DCD
4 DTR circuit
6 DSR
7 RTS
circuit
8 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND
1 DCD
4 DTR circuit
6 DSR
7 RTS
circuit
8 CTS

260
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
1 DCD
4 DTR circuit
6 DSR
7 RTS
circuit
8 CTS

Driver Version:
Version Date Description
V1.00 Oct/31/2011 Driver released.

261
PLC Connection Guide

Mitsubishi AJ71 (Format 4)

Supported Series: Mitsubishi A series PLC with AJ71C24 communication module using
the Computer Link protocol.
Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi AJ71 (Format 4)
PLC I/F RS485 4W RS485 4W, RS232
Baud rate 19200 9600, 19200
Data bits 8 8
Parity Even Even, Odd, None
Stop bits 1 1
PLC sta. no. 0

PLC Setting:
Communication mode Computer Link protocol 9600, Even, 8, 1 (default)
Mode setting switch Format 4
Parity check Enable
Sum check Enable

262
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 4W AJ71C24 RS422
9P D-Sub Male Terminal
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W AJ71C24 RS422
9P D-Sub Male Terminal
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

MT6050i/MT8050i
COM1 RS485 4W AJ71C24 RS422
9P D-Sub Female Terminal
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

263
PLC Connection Guide
The following represents the cable end connector.
A1SJ71UC24-R2
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
1 DCD
4 DTR circuit
6 DSR
7 RTS
circuit
8 CTS

MT6000/8000 series except MT6050i/MT8050i

264
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
1 DCD
4 DTR circuit
6 DSR
7 RTS
circuit
8 CTS

Driver Version:
Version Date Description
V1.00 Mar/08/2010

265
PLC Connection Guide

Mitsubishi F930GOT Server

Supported Series: F930GOT general-purpose communication Type 1.

HMI Setting:
Parameters Recommended Options Notes
PLC type F930GOT Server
PLC I/F RS232
Baud rate 38400 9600, 115200
Data bits 8 7 or 8
Parity None Even, Odd, None
Stop bits 1 1 or 2
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
B RB DDDD 0 ~ 2047
W RW DDDDD 0 ~ 65535

Note: In PLC name drop - down menu don’t select F930GOT Server.
Please select Local HMI, Device Type=RW.

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P Micro Computer Board
D-Sub Female D-Sub Female RS232 Female
2 RX 8 RX 3 TD
3 TX 7 TX 2 RD
5 GND 5 GND 5 GND

266
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P Micro Computer Board
D-Sub Female D-Sub Female D-Sub Male RS232 Female
2 RX 6 RX 8 RX 3 TD
3 TX 4 TX 7 TX 2 RD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P Micro Computer Board
D-Sub Female RS232 Female
9 RX 3 TD
6 TX 2 RD
5 GND 5 GND

Protocol:
Read Command:
PC  HMI
02 ‘0’ Read address Size CR

02 30 30 30 30 30 30 32 0D
Read RW0 1 word (2 bytes) STX = 0x02, ‘0’ = Read command, CR = 0x0D
Read address (hexadecimal)
0 ~ FFFF = RW0 ~ 65535
Size (hexadecimal)
2 ~ FE = 2 ~ 254 bytes = 1 ~ 127 word.
Size must be even.

HMI  PC (response)
02 Data1 Data2 ……. CR

02 30 30 31 30 0D
RW0 = 0x0010 = 16

267
PLC Connection Guide
Write Command:
PC  HMI
02 ‘1’ Read address Size Data1 Data2 ……. CR

02 31 30 30 30 30 30 32 12 34 0D
Write RW0 = 0x1234
Read address (hexadecimal)
0 ~ FFFF = RW0 ~ 65535
Size (hexadecimal)
2 ~ FE = 2 ~ 254 bytes = 1 ~ 127 word.
Size must be even.

HMI  PC (response)
06
ACK = 0x06

Driver Version:
Version Date Description
V1.00 Aug/14/2009 Driver released.

268
PLC Connection Guide

Mitsubishi FX0s/FX0n/FX1s/FX1n/FX2
Supported Series: Mitsubishi FX0s/FX0n/FX1s/FX1n/FX2 PLC

Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi FX0s/FX0n/FX1s/FX1n/FX2
PLC I/F RS485 4W RS232/RS485
9600/19200/38400/
Baud rate 9600
57600/115200
Data bits 7 7,8
Parity Even Even, Odd, None
Stop bits 1 1,2
PLC sta. no. 0 0-255

Device Address:
Bit/Word Device type Format Range Memo
B X OOO 0 ~ 377 Input Relay
B Y OOO 0 ~ 377 Output Relay
B M DDDD 0 ~ 9999 Auxiliary Relay
B T DDD 0 ~ 255 Timer Relay
B C DDD 0 ~ 255 Counter Relay
B SM DDDD 8000 ~ 9999 Special Aux. Relays
B D_Bit DDDDdd 0 ~ 999915 Data Register Bit (D)
B S DDDD 0 ~ 4095 States
W TV DDD 0 ~ 255 Timer Memory
W CV DDD 0 ~ 199 Counter Memory
W D DDDD 0 ~ 9999 Data Register
DW CV2 DDD 200 ~ 255 Counter Memory(D Word)
W SD DDDD 8000 ~ 9999 Special Data Register

269
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 4W RS422 Port 8P
9P D-Sub Male Mini-DIN Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS422 Port 8P
9P D-Sub Male Mini-DIN Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

MT6050i/MT8050i
COM1 RS485 4W RS422 Port 8P
9P D-Sub Female Mini-DIN Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

270
PLC Connection Guide
The following represents the cable end connector..
9P D-Sub to 25P D-Sub:
eMT3000 series
COM1 RS485 4W RS422 Port 8P
9P D-Sub Male Mini-DIN Male
1 RX- 16 TXD-
2 RX+ 3 TXD+
3 TX- 15 RXD-
4 TX+ 2 RXD+
5 GND 7 GND
4 DSR+ circuit
8 GND
13 +5V
circuit
17 DSR-

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS422 Port 8P
9P D-Sub Male Mini-DIN Male
1 RX- 16 TXD-
2 RX+ 3 TXD+
3 TX- 15 RXD-
4 TX+ 2 RXD+
5 GND 7 GND
4 DSR+ circuit
8 GND
13 +5V
circuit
17 DSR-

271
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W RS422 Port 8P
9P D-Sub Female Mini-DIN Male
1 RX- 16 TXD-
2 RX+ 3 TXD+
3 TX- 15 RXD-
4 TX+ 2 RXD+
5 GND 7 GND
4 DSR+ circuit
8 GND
13 +5V
circuit
17 DSR-

Driver Version:
Version Date Description
V1.20 Oct/26/2011

272
PLC Connection Guide

Mitsubishi FX232/485BD
Supported Series: Mitsubishi FX0n/FX2/FX2n COM for Communication Module BD
FX2N-485-BD, FX2N-232-BD, FX1N-485-BD, FX1N-232-BD & FX3U-485ADP.
Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi FX232/485BD
in accordance with the BD
PLC I/F RS232/RS485 RS232/RS485 2w/4w
module
Baud rate 19200 9600/19200/38400
Data bits 7 7,8
Parity Even Even, Odd, None
Stop bits 1 1,2
PLC sta. no. 1 0-15
Note: It is recommended to set turn around delay to 8. (For RS485 2W)

Online simulator YES Extend address mode YES

PLC Setting:
Communication mode Must set PLC station when useing BD Module.
Register D8120 setting: set b9 and b8 of BFM#0 to 0.

FX2N-485-BD, FX1N-485-BD FX2N-232-BD, FX1N-232-BD

273
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
B X OOO 0 ~ 377 Input Relay
B Y OOO 0 ~ 377 Output Relay
B M DDDD 0 ~ 7999 Auxiliary Relay
B T DDD 0 ~ 511 Timer Relay
B C DDD 0 ~ 255 Counter Relay
B SM DDDD 8000 ~ 9999 Special Auxiliary Relay
B D_Bit DDDDh 0 ~ 7999f Data Register Bit
B S DDDD 0 ~ 4095 State Relay
W TV DDD 0 ~ 255 Timer Memory
W CV DDD 0 ~ 199 Counter Memory
W D DDDD 0 ~ 7999 Data Register
W CV2 DDD 200 ~ 255 Counter Memory(D Word)
W SD DDDD 8000 ~ 9999 Special Data Register

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 9P D-Sub: Communication Module RS232BD
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND

274
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND

The following represents the cable end connector.

Communication Module RS485BD: RS485 4W
eMT3000 series
COM1 RS485 4W 485BD Module 5P
9P D-Sub Male Termanal
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND SG

275
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 4W 485BD Module 5P
9P D-Sub Male Termanal
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND SG

MT6050i/MT8050i
COM1 RS485 4W 485BD Module 5P
9P D-Sub Female Termanal
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND SG

The following represents the cable end connector.

Communication Module RS485BD: RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W 485BD Module 5P
9P D-Sub Male 9P D-Sub Male Termanal
1 RX- 6 Data- SDB
circuit
RDB
2 RX+ 9 Data+ SDA
circuit
RDA
5 GND 5 GND SG

276
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W 485BD Module 5P
9P D-Sub Male 9P D-Sub Male Termanal
1 RX- 6 Data- SDB
circuit
RDB
2 RX+ 9 Data+ SDA
circuit
RDA
5 GND 5 GND SG

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W 485BD Module 5P
9P D-Sub Female 9P D-Sub Female Termanal
1 RX- 7 Data- SDB
circuit
RDB
2 RX+ 8 Data+ SDA
circuit
RDA
5 GND 5 GND SG

Driver Version:
Version Date Description
V1.40 Jul/26/2011 Added registers: D_Bit and S.

277
PLC Connection Guide

Mitsubishi FX2n
Supported Series: Mitsubishi FX1n/FX2n series PLC

Website http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi FX2n
PLC I/F RS485 4W RS232/RS485
Baud rate 19200 9600/19200/38400
Data bits 7 /57600/115200
Parity Even
Stop bits 1
PLC sta. no. 0

Online simulator YES Extend address mode NO

Device Address:
Bit/Word Device type Format Range Memo
B X OOO 0 ~ 377 Input Relay
B Y OOO 0 ~ 377 Output Relay
B M DDDD 0 ~ 7999 Auxiliary Relay
B T DDD 0 ~ 255 Timer Relay
B C DDD 0 ~ 255 Counter Relay
B SM DDDD 8000 ~ 9999 Special Auxiliary Relay
B D_Bit DDDDdd 0 ~ 799915 Data Register Bit (D)
B S DDDD 0 ~ 4095 State Relay (S)
W TV DDD 0 ~ 255 Timer Memory
W CV DDD 0 ~ 199 Counter Memory
W D DDDD 0 ~ 7999 Data Register
DW CV2 DDD 200 ~ 255 Counter Memory(D Word)
W SD DDDD 8000 ~ 9999 Special Data Register

278
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
Mitsubishi FX series
eMT3000 series
COM1 RS485 4W RS422 8P Mini-DIN
9P D-Sub Male Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS422 8P Mini-DIN
9P D-Sub Male Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

279
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W RS422 8P Mini-DIN
9P D-Sub Female Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

Driver Version:
Version Date Description
V1.60 Sep/10/2009

280
PLC Connection Guide

Mitsubishi FX3u (Ethernet)

Supported Series: Mitsubishi FX SERIES, Module: FX3U-ENET.

Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi FX3u (Ethernet)
PLC I/F Ethernet
Port no. 5001(default) Refer to Module Setting
PLC sta. no. 0 (default) Refer to Module Setting

PLC Setting:
Fx3u-ENET module setting:
Before using Ethernet module, use GX Developer / FX Configurator-EN to set the Ethernet
module, the FX3u-ENET module setting steps are shown below.

Step1. Open GX Developer, select “Read from PLC” in Online list.

281
PLC Connection Guide
Step2. Select “FXCPU” in PLC series.

Step3. Connect PLC via serial port for setting IP address first.

282
PLC Connection Guide
Step4. After finishing the PLC settings, select Tools/FX special function utility/FX
Configurator-EN.

Step5. Select “Module 0” in Ethernet Module settings.

(If more than one module needed, please set modules step by step)

283
PLC Connection Guide

Step6. In Ethernet operational settings, select the related parameters and IP address and
then press ”End” to finish setting.

Step7. In Ethernet open settings, press “End” after setting the parameters below.

(The first Protocol means using GX Developer to communicate with module, the max.
“Fixed buffer communication preocedure” is 4 units.)

284
PLC Connection Guide

285
PLC Connection Guide
Step8. After setting the parameters of PLC, restart for Ethernet communication.

Device Address:
Bit/Word Device type Format Range Memo
B X OOO 0 ~ 571 Input
B Y OOO 0 ~ 571 Output Relay
B M DDDD 0 ~ 7999 Internal Relay
B T DDD 0 ~ 511 Timer Contacts
B C DDD 0 ~ 255 Counter Contacts
B SM DDDD 8000 ~ 8511 Special Int. Relays
B D_Bit DDDDDdd 0 ~ 1799915 Data Register Bit Access
B S DDDD 0 ~ 4095 Step Relays
W TV DDD 0 ~ 511 Timer Value
W CV DDD 0 ~ 199 Counter Value
W D DDDD 0 ~ 7999 Data Registers
W CV2 DDD 200 ~255 Counter Value
W SD DDDD 8000 ~ 8511 Special Data Registers
W R DDDDD 0 ~ 32767 File Register

286
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 Feb/12/2009 Driver released.

287
PLC Connection Guide

Mitsubishi FX3u/FX3G
Supported Series: Mitsubishi FX3U/FX3UC/FX3G.
Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi FX3u/FX3G
PLC I/F RS485 4w RS232/RS485
Baud rate 38400 2w/4w
9600/19200
Data bits 7
Parity Even
Stop bits 1
PLC sta. no. 0 Does not apply to this protocol

Online simulator YES (9600 baud rate only) Extend address mode NO

Device Address:
Bit/Word Device type Format Range Memo
B X OOO 0 ~ 764 Input Relay
B Y OOO 0 ~ 764 Output Relay
B M DDDD 0 ~ 7999 Auxiliary Relay
B T DDD 0 ~ 511 Timer Relay (T)
B C DDD 0 ~ 255 Counter Relay (C)
B SM DDDD 8000 ~ 9999 Special Relay (M)
B D_Bit DDDDdd 0 ~ 799915 Data Register Bit (D)
B S DDDD 0 ~ 4095 State Relay (S)
W TV DDD 0 ~ 511 Timer Memory (T)
W CV DDD 0 ~ 199 Counter Memory (C)
W D DDDD 0 ~ 7999 Data Register (D)
DW CV2 DDD 200 ~ 255 Counter Memory(D Word)
W SD DDDD 8000 ~ 9999 Special Data Register (D)
W R DDDDD 0 ~ 32767 Extended Register (R)
W Z D 0~7 Index register

288
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 4W RS422 8P Mini-DIN
9P D-Sub Male Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS422 8P Mini-DIN
9P D-Sub Male Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

MT6050i/MT8050i
COM1 RS485 4W RS422 8P Mini-DIN
9P D-Sub Female Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

289
PLC Connection Guide

Driver Version:
Version Date Description
V1.71 Nov/15/2010

290
PLC Connection Guide

Mitsubishi MELSEC-Q/L (Ethernet)

Supported Series: Mitsubishi Q series (Q03UDE, Q04UDEH, Q06UDEH, Q10UDEH,
Q13UDEH, Q20UDEH, Q26UDEH), Mitsubishi L series, MELSEC-Q protocol application
to CPU of Ethernet interface or Ethernet module.
Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi MELSEC-Q/L (Ethernet)
PLC I/F Ethernet
Set identically to the PLC
Port no. Adviced to set port no. to 4999
setting
Networking no. (Set
Parameter 1 0~255 Q13UDEH has to be set to 0
identically to PLC setting)
Set identically to the PLC Q13UDEH has to be set to
PLC sta. no. 255
setting 255

PLC Setting:
MITSUBISHI Q/L series Ethernet module setting:
Note: If using QJ71E71 module, please refer to MITSUBISHI QJ71E71 connection guide.

291
PLC Connection Guide
1. Click [PLC parameter].
2. [Built-in Ethernet port].
3. Click [Open settings] and then set the IP address and communication data code
4. Set the MC protocol-TCP Port No.1387 (Hex) and in EasyBuilder, TCP port is 4999
(Dec).

Note: In EasyBuilder, please fill in [Network No.] in Parameter 1 as PLC setting.

For example below, the Network No. is 2.

Set to 2 for Parameter 1 in EasyBuilder.

292
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
B SM DDDD 0 ~ 2047 Special Relay
B X HHHH 0 ~ 1fff Input Relay
B Y HHHH 0 ~ 1fff Output Relay
B M DDDDD 0 ~ 61439 Internal Relay
B L DDDDD 0 ~ 32767 Latch Relay
B F DDDDD 0 ~ 32767 Annunciator
B V DDDDD 0 ~ 32767 Edge Relay
B B HHHH 0 ~ efff Link Relay
B TS DDDDD 0 ~ 25471 Timer Contact
B TC DDDDD 0 ~ 25471 Timer Coil
B SS DDDDD 0 ~ 25471 Retentive Timer Contact
B SC DDDDD 0 ~ 25471 Retentive Timer Coil
B CS DDDDD 0 ~ 25471 Counter Contact
B CC DDDDD 0 ~ 25471 Counter Coil
B SB HHHH 0 ~ 7fff Special Link Relay
B S DDDD 0 ~ 8191 Step relay
B DX HHHH 0 ~ 1fff Direct Input
B DY HHHH 0 ~ 1fff Direct Output
B D_Bit DDDDDDDh 0 ~ 4184063f Data Register bit
B SD_bit DDDDh 0 ~ 2047f Special register Bit
B ZR_bit HHHHHHh 0 ~ 3fd7fff File Register Bit
B R_bit DDDDDh 0 ~ 32767f File Register Bit
B SW_bit HHHh 0 ~ 7fff Special Link Register Bit
B W_bit HHHHHHh 0 ~ 3fd7fff Link Register Bit
W SD DDDD 0 ~ 2047 Special register
W D DDDDDDD 0 ~ 4184063 Data Register
W W HHHHHH 0 ~ 3fd7ff Link Register
W TN DDDDD 0 ~ 25471 Timer Current value
Retentive Timer Current
W SN DDDDD 0 ~ 25471
value
W CN DDDDD 0 ~ 25471 Counter Current value
W SW HHH 0 ~ 7ff Special Link Register
W Z DD 0 ~ 20 Index Register
W R DDDDD 0 ~ 32767 File Register
W ZR HHHHHH 0 ~ 3fd7ff File Register

293
PLC Connection Guide
Note: Each model of CPU is different, it is recommended to refer to MITSUBISHI
MELSEC-Q Manual Device List.

Driver Version:
Version Date Description
V1.30 Jan/14/2011

294
PLC Connection Guide

Mitsubishi MR J3 A
Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi MR J3 A
PLC I/F RS485 4W RS232/RS485
Baud rate 9600 9600~115200
Parity Even
Data bits 8
Stop bits 1
PLC sta. no. 0 0~31

Device Address:
Bit/Word Device type Format Range Memo
B EIP DD 0 ~ 31 External input pin status read**
B EOP DD 0 ~ 31 External output pin status read**
W PA DD 1 ~ 19 Basic Setting
W PB DD 1 ~ 45 Gain / Filter Setting
W PC DD 1 ~ 50 Extension Setting
W PD DD 1 ~ 30 Input / Output Setting
W Status DD 0 ~ 17 Amplifier Status
W Alarm D 0~6 Alarm
W Alarm_T D 0~6 Alarm Time (Hour)
W Mode D 1~4 Write Only, Mode Setting*
W Speed D 0~1 Write Only, Set Current Speed *
W Acc D 0~1 Write Only, Set Acceleration*
W Rotation D 0~1 Write Only, Rotation Direction*
W End D 0~1 Write Only, End*
W M_dist D 0~1 Write Only, Moving Distance*
W Rot_P D 0~1 Write Only, Rotation Position*
W P_start D 0~1 Write Only, Start Positioning*
Note: 1.* represents the write-only registers. The usage of this kind of registers is to run
Jog Mode and Positioning Mode.
2.** represents the read-only registers.

295
PLC Connection Guide
EIP:

EOP:

296
PLC Connection Guide
How to use EasyBuilder8000/Easy BuilderPro to run Jog and Positioning Mode

*Jog Mode
To run Jog Mode, please follow the steps listed sequentially:
(1) Set Jog Mode
(2) Set rotation speed
(3) Set acceleration
(4) Set forward / reverse rotation direction
(5) End

The following shows how to run the steps above using Macro in
EasyBuilder8000/Easy BuilderPro.

On the editing window of EasyBuilder8000/Easy BuilderPro, the write address of

“speed” is set to Local HMI LW0 (the address can be user-defined), and set “Acc”
(Acceleration) to LW1.
To run Jog Mode, the communication with the device must be continuous which only
allows an interval less than 0.5 seconds, otherwise the motor will be locked. Therefore,
in this example, only one register PA_1 is set to read device value.

Macro Demonstration:
a. Start Macro
macro_command main()
short speed
short acc
short mode
mode = 1 // This represents Jog Mode.

SetData(mode, "MITSUBISHI MR J3 A", Mode, 1, 1) // Set driver mode to Jog.

GetData(speed, "Local HMI", LW, 0, 1) // Save LW0 value to speed.

SetData(speed, "MITSUBISHI MR J3 A", Speed, 0, 1) // Set motor operating speed.

297
PLC Connection Guide

GetData(acc, "Local HMI", LW, 1, 1) //

SetData(acc, "MITSUBISHI MR J3 A", Acc, 0, 1) // Set motor acceleration.

short motion
motion = 0x0801 // Special code, see Note 1.

SetData(motion, "MITSUBISHI MR J3 A", Rotation, 0, 1) // Rotate.

end macro_command

Note 1. Original Factory Manual:

b. End Macro
macro_command main()

short stop
stop = 1 // See Note 2.

SetData(stop, "MITSUBISHI MR J3 A", End, 1, 1)

end macro_command

Note 2. Original Factory Manual:

298
PLC Connection Guide
*Positioning Mode

On the editing window of EasyBuilder8000/Easy BuilderPro, the write address of

“Speed” is set to Local HMI LW2 (the address can be user-defined), and set “Acc”
(Acceleration) to LW3, “Move distance” to LW4 (DW format).

Macro Demonstration:
macro_command main()

short mode
mode = 0x2 // Positioning Mode
SetData(mode, "MITSUBISHI MR J3 A", Mode, 1, 1)

short speed
GetData(speed, "Local HMI", LW, 2, 1)
SetData(speed, "MITSUBISHI MR J3 A", Speed, 0, 1)

short acc
GetData(acc, "Local HMI", LW, 3, 1)
SetData(acc, "MITSUBISHI MR J3 A", Acc, 0, 1)

short dist
GetData(dist, "Local HMI", LW, 4, 1)
SetData(dist, "MITSUBISHI MR J3 A", M_dist, 0, 1)

short rot_P
rot_P = 1 // Set to 0: Forward Rotation 1: Reverse Rotation
SetData(rot_P, "MITSUBISHI MR J3 A", Rot_P, 0, 1)

short rotat
rotat = 1 // See Note 3.

299
PLC Connection Guide
SetData(rotat, "MITSUBISHI MR J3 A", Rotation, 0, 1)

SetData(rot_P, "MITSUBISHI MR J3 A", P_start, 0, 1) // Start Positioning.

end macro_command

Note 3. Original Factory Manual

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 4W CN3 RS485 4W RJ45
9P D-Sub Male Male
1 RX- 4 TX-
2 RX+ 5 TX+
3 TX- 6 RX-
4 TX+ 3 RX+
5 GND 7 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W CN3 RS485 4W RJ45
9P D-Sub Male Male
1 RX- 4 TX-
2 RX+ 5 TX+
3 TX- 6 RX-
4 TX+ 3 RX+
5 GND 7 GND

300
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W CN3 RS485 4W RJ45
9P D-Sub Female Male
1 RX- 4 TX-
2 RX+ 5 TX+
3 TX- 6 RX-
4 TX+ 3 RX+
5 GND 7 GND

Driver Version:
Version Date Description
V1.00 Sep/01/2011 Driver released.
V1.10 Jan/13/2012 Added register: EIP and EOP.

301
PLC Connection Guide

Mitsubishi MR-MQ100 (Ethernet)

Supported Series: Mitsubishi MR-MQ100-Ethernet
Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi MR-MQ100 (Ethernet)
PLC I/F Ethernet
Set identically to the PLC Adviced to set port no. to
Port no.
setting 4999
Parameter1 1 Network No.
PLC sta. no. 255

PLC Setting:

302
PLC Connection Guide
1. Click [Basic Setting].
2. [Built-in Ethernet Port Setting].
3. Click [Open Setting] and then set the IP address and communication data code.
4. Set the MC Protocol-TCP Port No. (Hex)

Device Address:
Bit/Word Device type Format Range Memo
B SM DDDD 0 ~ 2255 Special Relay
B X HHHH 0 ~ 1fff Input
B Y HHHH 0 ~ 1fff Output
B M DDDDD 0 ~ 61439 Internal Relay
B F DDDDD 0 ~ 32767 Annunciator
B B HHHH 0 ~ efff Link Relay
B D_Bit DDDDDDDh 0 ~ 4184063f
W SD DDDD 0 ~ 2255 Special Register
W D DDDDDDD 0 ~ 4184063 Data Register
W W HHHHHH 0 ~ 3fd7ff Link Register
W # DDDDD 0 ~ 12287 Motion Register
Note: ddd: Decimal, hhh: Hexadecimal, ooo: Octal.

303
PLC Connection Guide
Through a hub:
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 1 TX+
2 TX- Orange 2 TX-
3 RX+ White/Green 3 RX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 6 RX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Driver Version:
Version Date Description
V1.10 Jun/08/2011 Added register: D_Bit

304
PLC Connection Guide

Mitsubishi Q00/Q00UJ/Q01/QJ71
Supported Series: Mitsubishi Q series PLC with QJ71C24 communication module, Q00,
Q00J, Q00UJ, Q01, Q02H, Q06H, Q12H, Q25H, Q12PH, Q25PH CPU port.

Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi Q00/Q00UJ/Q01/QJ71
PLC I/F RS232 RS485 4W, RS232
Baud rate 9600 9600~115200
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. 0

Online simulator YES

Extend address mode NO

PLC Setting:
Q00, Q01 CPU port setting:
1. In GX Developer “PLC data list” click [PLC parameter].
2. In “PLC parameter” go to [Serial] page.
3. Select [Use serial communication].
4. Set [Transmission speed] to 9600~115200.
5. Select [Sum check].
6. Set [Transmission wait time] to 10ms.
7. Permit [RUN write setting].
8. Click [End] to close the dialog.
9. Write the PLC Parameter to PLC.
10. Reset PLC, the parameter will be actived.

305
PLC Connection Guide

QJ71 setting:

306
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
B X HHHH 0 ~ 1fff Input Relay
B Y HHHH 0 ~ 1fff Output Relay
B M DDDD 0 ~ 8191 Internal Relay
B L DDDD 0 ~ 8191 Latch Relay
B F DDDD 0 ~ 2047 Annunciator
B V DDDD 0 ~ 2047 Edge Relay
B B HHHH 0 ~ 1fff Link Relay
B TC DDDD 0 ~ 2047 Timer Coil
B SS DDDD 0 ~ 2047 Retentive Timer Contact
B SC DDDD 0 ~ 2047 Retentive Timer Coil
B CS DDDD 0 ~ 1023 Counter Contact
B CC DDDD 0 ~ 1023 Counter Coil
B SB HHH 0 ~ 7ff Special Link Relay
B S DDDD 0 ~ 8191 Step Relay
B DX HHHH 0 ~ 1fff Direct Input
B DY HHHH 0 ~ 1fff Direct Output
B TS DDDD 0 ~ 2047 Timer Contact
B SM DDDD 0 ~ 2047
B D_Bit DDDDDh 0 ~ 12287f
W W HHHH 0 ~ 2fff Link Register
W TN DDDD 0 ~ 2047 Timer Current Value
W SN DDDD 0 ~ 2047 Retentive Timer Current Value
W CN DDDD 0 ~ 1023 Counter Current Value
W R DDDDD 0 ~ 32767 File Register
W SW HHH 0 ~ 7ff Special Link Register
W Z DD 0 ~ 15 Index Register
W ZR HHHH 0 ~ ffff File Register
W D DDDDD 0 ~ 12287 Data Register
W SD DDDD 0 ~ 2047

307
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
QJ71C24 CH.2 RS422 Terminal
eMT3000 series
COM1 RS485 4W QJ71C24 CH.2 RS422
9P D-Sub Male Terminal
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W QJ71C24 CH.2 RS422
9P D-Sub Male Terminal
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

308
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W QJ71C24 CH.2 RS422
9P D-Sub Female Terminal
1 RX- SDB
2 RX+ SDA
3 TX- RDB
4 TX+ RDA
5 GND GND

The following represents the cable end connector.

QJ71C24 CH.2 RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P QJ71C24 CH.1 RS232
D-Sub Female D-Sub Female 9P D-Sub Male
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
1 DCD
4 DTR circuit
6 DSR
7 RTS
circuit
8 CTS

309
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P QJ71C24 CH.1 RS232
D-Sub Female D-Sub Female D-Sub Male 9P D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND
1 DCD
4 DTR circuit
6 DSR
7 RTS
circuit
8 CTS

MT6050i/MT8050i
COM1 RS232 9P QJ71C24 CH.1 RS232
D-Sub Female 9P D-Sub Male
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
1 DCD
4 DTR circuit
6 DSR
7 RTS
circuit
8 CTS

310
PLC Connection Guide
The following represents the cable end connector.
9P D-Sub to 6P Mini-DIN: Q00, Q01 CPU port RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 6P Mini-DIN
D-Sub Female D-Sub Female Male
2 RX 8 RX 3 TXD
3 TX 7 TX 4 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 6P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 6P Mini-DIN
D-Sub Female Male
9 RX 3 TXD
6 TX 4 RXD
5 GND 5 GND

311
PLC Connection Guide
The following represents the cable end connector.
9P D-Sub to 6P Mini-DIN: Q00UJ CPU port RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 6P Mini-DIN
D-Sub Female D-Sub Female Male
2 RX 8 RX 3 TXD
3 TX 7 TX 4 RXD
5 GND 5 GND 5 GND
1 RTS
circuit
6 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 6P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 5 GND
1 RTS
circuit
6 CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 6P Mini-DIN
D-Sub Female Male
9 RX 3 TXD
6 TX 4 RXD
5 GND 5 GND
1 RTS
circuit
6 CTS

312
PLC Connection Guide

Driver Version:
Version Date Description
V1.80 Jun/08/2011 Added register: D_Bit
V1.90 Sep/23/2011 Fixed bit communication incorrect.

313
PLC Connection Guide

Mitsubishi Q00J
Supported Series: Mitsubishi Q00J CPU

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi Q00J
PLC I/F RS232 CPU port
9600,19200,38400,
Baud rate 115200
57600,115200
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no.

Device Address:
Bit/Word Device type Format Range Memo
B SM DDDD 0 ~ 1023
B X HHH 0 ~ 7ff
B Y HHH 0 ~ 7ff
B M DDDD 0 ~ 8191
B L DDDD 0 ~ 2047
B F DDDD 0 ~ 1023
B V DDDD 0 ~ 1023
B B HHH 0 ~ 7ff
B SB HHH 0 ~ 3ff
B D_Bit DDDDDh 0 ~ 11135f
W SD DDDD 0 ~ 1023
W D DDDDD 0 ~ 11135
W W HHH 0 ~ 7ff
W SW HHH 0 ~ 3ff
W Z D 0~9
W C DDD 0 ~ 511
W T DDD 0 ~ 511

314
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 6P Mini-DIN: Q00 CPU port RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 6P Mini-DIN
D-Sub Female D-Sub Female Male
2 RX 8 RX 3 TXD
3 TX 7 TX 4 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 6P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 6P Mini-DIN
D-Sub Female Male
9 RX 3 TXD
6 TX 4 RXD
5 GND 5 GND

MT8-Mitsubishi-Q-3M cable can connect MT8000 with Mitsubishi Q series directly.

Driver Version:
Version Date Description
V1.20 Jun/08/2011 Added register D_bit
315
PLC Connection Guide

Mitsubishi Q00U/Q01U/Q02U/QnUD/QnUDH
Supported Series: Mitsubishi Q00U, Q01U, Q02U, Q03UD, Q04UDH, Q06UDH, Q10UDH,
Q13UDH, Q20UDH, Q26UDH CPU.

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi Q00U/Q01U/Q02U/QnUD/QnUDH
PLC I/F RS232 RS485 4W, RS232 CPU port direct connect
9600,19200,38400,57600,115200
Baud rate 115200 115200 only
For Q00UJ, only 9600 is available
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. No

Device Address:
Bit/Word Device type Format Range Memo
B SM DDDD 0 ~ 2047
B X HHHH 0 ~ 1fff Input Relay
B Y HHHH 0 ~ 1fff Output Relay
B M DDDD 0 ~ 8191 Internal Relay
B L DDDD 0 ~ 8191 Latch Relay
B F DDDD 0 ~ 2047 Annunciator
B V DDDD 0 ~ 2047 Edge Relay
B B HHHH 0 ~ 1fff Link Relay
B SB HHH 0 ~ 7ff Special Link Relay
B D_Bit DDDDDh 0 ~ 12287f
W SD DDDD 0 ~ 2047
W D DDDDD 0 ~ 12287 Data Register
W W HHHH 0 ~ 1fff Link Register
W SW HHH 0 ~ 7ff Special Link Register
W Z DD 0 ~ 19 Index Register
W R DDDDD 0 ~ 32767
W C DDDD 0 ~ 1023 Counter Current Value
W T DDDD 0 ~ 2047 Timer Current Value

316
PLC Connection Guide

Note:
EasyBuilder doesn’t support MITSUBISHI Q02U CPU to do on-line simulation on PC.
When using Q02U driver, HMI needs 10 seconds to initiate PLC Q02U driver. Before the
completion of initiation, it is recommended not to wrire data to PLC, this could cause “PLC
no response”； Incorrect wiring or data could cause PLC to be locked. If PLC is locked,
please restart PLC or reinstall PLC module.

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 6P Mini-DIN: Q02 CPU port RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 6P Mini-DIN
D-Sub Female D-Sub Female Male
2 RX 8 RX 3 TXD
3 TX 7 TX 4 RXD
5 GND 5 GND 5 GND
1 RTS
circuit
6 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 6P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 5 GND
1 RTS
circuit
6 CTS

317
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 6P Mini-DIN
D-Sub Female Male
9 RX 3 TXD
6 TX 4 RXD
5 GND 5 GND
1 RTS
circuit
6 CTS

Driver Version:
Version Date Description
V1.60 Jun/08/2011 Added register D_bit

318
PLC Connection Guide

Mitsubishi Q00UJ/QnU/QnUD/QnUDH/QnUDEH
(mini USB)
Supported Series: Mitsubishi Q00UJ, Q00U, Q01U, Q02U, Q03UDE, Q03UD, Q04UDEH,
Q04UDH, Q06UDEH, Q06UDH, Q10UDEH, Q10UDH, Q13UDEH, Q13UDH, Q20UDEH,
Q20UDH, Q26UDEH, Q26UDH USB Port.

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi Q00UJ/QnU/QnUD/QnUDH/QnUDEH (mini USB)
PLC I/F USB CPU port direct connect

319
PLC Connection Guide

Driver Version:
Version Date Description
V1.30 Jun/08/2011 Added register D_bit

320
PLC Connection Guide

Mitsubishi Q02/02H
Supported Series; Mitsubishi Q02/Q02H CPU port.

Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi Q02/02H
PLC I/F RS232 RS485 4W, RS232
Baud rate 115200 115200 only
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. 0

Online simulator YES Extend address mode NO

Broadcast command NO

321
PLC Connection Guide
Bit/Word Device type Format Range Memo
B DX HHHH 0 ~ 1fff Direct Input
B DY HHHH 0 ~ 1fff Direct Output
B TS DDDD 0 ~ 2047 Timer Contact
B D_Bit DDDDDh 0 ~ 12287f
W W HHHH 0 ~ 1fff Link Register
W TN DDDD 0 ~ 2047 Timer Current Value
W SN DDDD 0 ~ 2047 Retentive Timer Current Value
W CN DDDD 0 ~ 1023 Counter Current Value
W R DDDDD 0 ~ 32767 File Register
W SW HHH 0 ~ 7ff Special Link Register
W Z DD 0 ~ 15 Index Register
W ZR HHHH 0 ~ ffff File Register
W D DDDDD 0 ~ 12287 Data Register

322
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 6P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 5 GND
1 RTS
circuit
6 CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 6P Mini-DIN
D-Sub Female Male
9 RX 3 TXD
6 TX 4 RXD
5 GND 5 GND
1 RTS
circuit
6 CTS

Driver Version:
Version Date Description
V1.60 Jun/08/2011 Added register D_bit

323
PLC Connection Guide

Mitsubishi Q06H
Supported Series: Mitsubishi Q06H CPU port.

Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi Q06H
PLC I/F RS232 RS485 4W, RS232
Baud rate 115200 115200 only
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. 0

Online simulator YES Extend address mode NO

Broadcast command NO

324
PLC Connection Guide
Bit/Word Device type Format Range Memo
B DX HHHH 0 ~ 1fff Direct Input
B DY HHHH 0 ~ 1fff Direct Output
B TS DDDD 0 ~ 2047 Timer Contact
B D_Bit DDDDDh 0 ~ 12287f
W W HHHH 0 ~ 1fff Link Register
W TN DDDD 0 ~ 2047 Timer Current Value
W SN DDDD 0 ~ 2047 Retentive Timer
W CN DDDD 0 ~ 1023 Current Value
Counter Current Value
W R DDDDD 0 ~ 32767 File Register
W SW HHH 0 ~ 7ff Special Link Register
W Z DD 0 ~ 15 Index Register
W ZR HHHH 0 ~ ffff File Register
W D DDDDD 0 ~ 12287 Data Register

325
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 6P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 5 GND
1 RTS
circuit
6 CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 6P Mini-DIN
D-Sub Female Male
9 RX 3 TXD
6 TX 4 RXD
5 GND 5 GND
1 RTS
circuit
6 CTS

Driver Version:
Version Date Description
V1.60 Jun/08/2011 Added register D_bit

326
PLC Connection Guide

Mitsubishi QJ71E71 (Ethernet)

Supported Series ; Mitsubishi Q type, MELSEC-Q series PLC (Q00J, Q00, Q01, Q02,
Q02H, Q06H, Q12H, Q25H, Q12PH, Q25PH) QJ71E71-100 Ethernet module.

Website: http://www.mitsubishi-automation.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Mitsubishi QJ71E71 (Ethernet)
PLC I/F Ethernet
Port no. 5002
PLC sta. no. 2 1~99

Note: MITSUBISHI QJ71E71 only supports PLC Network No. 1.

If PLC Network No. is not 1, please use “MISTSUBISHI MELSEC-Q(Ethernet)” driver and
fill in the Network No. in Parameter 1. Please refer to MISTSUBISHI MELSEC-Q(Ethernet)
for further information.

PLC Setting:
QJ71E71-100 Ethernet module settings:
1. Use USB or RS232 of Q-CPU for setting PLC parameters.

327
PLC Connection Guide
2. Click [Operational settings] to set IP information.

328
PLC Connection Guide
3. Select Ethernet (2.0) for communicating with HMI.

4. Click [Open settings] to set the system.

329
PLC Connection Guide
5. Press [END] to finish settings.

6. Restart PLC software and select [READ FROM PLC], select [QCPU(Qmode)]
and press [OK].

7. In [PC side I/F Ethernet board setting] set Network No. and Station No.
(Station No.1 is PC Station No. not Ethernet module Station No., ranged
from 2~64, the Network No. can not be the same as that of PC)

330
PLC Connection Guide
8. Select “Ethernet module” in PLC Side I/F to set QJ71E71 IP address.(IP
address = Network Parameter IP address)

9. For “Other station”, click [Other station(Single network)”] for setting [Check
at communication time] and [Retry times].

10. After finishing the settings above, click [Connection test] for testing the
communication and sending the PLC program.

331
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
B SM DDDD 0 ~ 2047
B X HHHH 0 ~ 1fff Input Relay
B Y HHHH 0 ~ 1fff Output Relay
B M DDDD 0 ~ 8191 Internal Relay
B L DDDD 0 ~ 8191 Latch Relay
B F DDDD 0 ~ 2047 Annunciator
B V DDDD 0 ~ 2047 Edge Relay
B B HHHH 0 ~ 1fff Link Relay
B TS DDDD 0 ~ 2047
B TC DDDD 0 ~ 2047
B SS DDDD 0 ~ 2047
B SC DDDD 0 ~ 2047
B CS DDDD 0 ~ 1023
B CC DDDD 0 ~ 1023
B SB HHH 0 ~ 7ff Special Link Relay
B S DDDD 0 ~ 8191
B DX HHHH 0 ~ 1fff Direct Input
B DY HHHH 0 ~ 1fff Direct Output
B D_Bit DDDDDh 0 ~ 12287f
W SD DDDD 0 ~ 2047
W D DDDDD 0 ~ 12287 Data Register
W W HHHH 0 ~ 1fff Link Register
W TN DDDD 0 ~ 2047
W SN DDDD 0 ~ 2047
W CN DDDD 0 ~ 1023
W SW HHH 0 ~ 7ff Special Link Register
W Z DD 0 ~ 15 Index Register
W R DDDDD 0 ~ 32767 File Register
W ZR HHHHH 0 ~ fe7ff File Register

332
PLC Connection Guide

Driver Version:
Version Date Description
V2.20 Jun/08/2011 Added register: D_bit

333
PLC Connection Guide

MODBUS ASCII
Supported Series: MODBUS ASCII CONTROLLER

Website: http://www.modbus.org

HMI Setting:
Parameters Recommended Options Notes
PLC type MODBUS ASCII
PLC I/F RS485 RS232/RS485
9600/19200/38400/
Baud rate 9600
57600/115200
Data bits 8 7,8
Parity Even Even, Odd, None
Stop bits 1 1,2
PLC sta. no. 1 0-255

Online simulator YES Broadcast command YES

Extend address mode YES

PLC Setting:
Communication mode Modbus ASCII protocol

Device Address:
Bit/Word Device type Format Range Memo
B 1x DDDDD 1 ~ 65535 Input bit (read only)
B 0x DDDDD 1 ~ 65535 Output bit
B 3x_Bit DDDDDdd 100 ~ 6553515 Input Register bit (read only)
B 4x_Bit DDDDDdd 100 ~ 6553515 Output Register bit
W 3x DDDDD 1 ~ 65535 Input Register (read only)
W 4x DDDDD 1 ~ 65535 Output Register
W 6x DDDDD 1 ~ 65535

334
PLC Connection Guide
Modbus RTU function code:
0x 0x01 Read coil 0x05 write single coil
1x 0x02 Read discrete input N/A for write operation
3x 0x04 Read input register N/A for write operation
4x 0x03 Read holding register 0x10 write multiple registers
3xbit is equivalent to 3x
4xbit is equivalent to 4x

Wiring Diagram:
The following represents the cable end connector.
Modbus ASCII Controller : RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female Female
2 RX 8 RX TXD
3 TX 7 TX RXD
5 GND 5 GND GND
RTS
circuit
CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Female
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND
RTS
circuit
CTS

335
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub
D-Sub Female Female
9 RX TXD
6 TX RXD
5 GND GND
RTS
circuit
CTS

The following represents the cable end connector.

Modbus ASCII Controller : RS485 4W
eMT3000 series
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

336
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Female Female
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

The following represents the cable end connector.

Modbus ASCII Controller : RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

337
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Female
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND GND

Driver Version:
Version Date Description
V1.40 Apr/17/2009

338
PLC Connection Guide

MODBUS ASCII Server

HMI Setting:
Parameters Recommended Options Notes
PLC type MODBUS ASCII Server
PLC I/F RS232 RS232, RS485
Baud rate 9600 9600~115200
Data bits 8 7,8
Parity Even Even, Odd, None
Stop bits 1 1
PLC sta. no. 1 1-31 HMI Modbus Station No.

Online simulator YES Extend address mode NO

Broadcast command NO

PLC Setting:
Communication mode Modbus ASCII protocol

Device Address:
Bit/Word Device type Format Range Memo
B LB dddd 0 ~ 9998 Mapping to 0x/1x 1 ~ 9999
W LW dddd 0 ~ 9998 Mapping to 3x/4x 1 ~ 9999
W RW ddddd 0 ~ 55536 Mapping to 3x/4x 10000 ~ 65536

LB0 = 0x0001, LB1 = 0x0002, LW0 = 3x0001, LW1 = 3x0002

Modbus RTU Server doesn’t support function code 06(preset single register), please use
function code 16(0x10, preset multiple registers).

Modbus Server Function Code:

339
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female Female
2 RX 8 RX TXD
3 TX 7 TX RXD
5 GND 5 GND GND
RTS
circuit
CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Female
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND
RTS
circuit
CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub
D-Sub Female Female
9 RX TXD
6 TX RXD
5 GND GND
RTS
circuit
CTS

340
PLC Connection Guide
The following represents the cable end connector.
RS485 4W
eMT3000 series
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Female Female
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

341
PLC Connection Guide
The following represents the cable end connector.
RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND GND

Note: Setting more than one Modbus ASCII Server in HMI Device List is of no effect.

Driver Version:
Version Date Description
V1.00 Feb/19/2009 Driver released

342
PLC Connection Guide

MODBUS RTU
Supported Series : MODBUS RTU CONTROLLER
Website : http://www.modbus.org

HMI Setting:
Parameters Recommended Options Notes
PLC type MODBUS RTU
PLC I/F RS485 RS232/RS485
Baud rate 9600 9600~115200
Data bits 8 7, 8
Parity Even Even, Odd, None
Stop bits 1 1, 2
PLC sta. no. 1 0-255

Online simulator YES Broadcast command YES

Extend address mode YES

PLC Setting:
Communication mode Modbus RTU protocol

Device Address:
Bit/Word Device type Format Range Memo
B 0x DDDDD 1 ~ 65535 Output bit
B 1x DDDDD 1 ~ 65535 Input bit (read only)
B 3x_Bit DDDDDdd 100 ~ 6553515 Input Register bit (read only)
B 4x_Bit DDDDDdd 100 ~ 6553515 Output Register bit
B 6x_Bit DDDDDdd 100 ~ 6553515 Output Register bit
B 0x_multi_coils DDDDD 1 ~ 65535 Write multiple coils
W 3x DDDDD 1 ~ 65535 Input Register (read only)
W 4x DDDDD 1 ~ 65535 Output Register
DW 5x DDDDD 1 ~ 65535 4x double word swap
W 6x DDDDD 1 ~ 65535 4x single word write
W 4x_32Bit* DDDDD 1 ~ 65535 Output Register
4x_32Bit will only read / write 2 words for each package, for continuous addresses, it will
be divided into several packages.
343
PLC Connection Guide

NOTE:
Address type “5x” is mapping to Hold Reg. The communication protocol of 5x is almost the
same as “4x” except that “5x” swaps double word.
If 4x contains the following information:
Address 1 2 3 4 5 6 ...
Data in word 0x1 0x2 0x3 0x4 0x5 0x6
Data 0x20001 0x40003 0x60005

For 5x, it will be:

Address 1 2 3 4 5 6 ...
Data in word 0x2 0x1 0x4 0x3 0x6 0x5
Data 0x10002 0x30004 0x50006

Modbus RTU function code:

0x 0x01 Read coil 0x05 write single coil
0x_multi_coils 0x01 Read coil 0x0f write multiple coils
1x 0x02 Read discrete input N/A for write operation
3x 0x04 Read input register N/A for write operation
4x 0x03 Read holding register 0x10 write multiple registers
5x 0x03 Read holding register 0x10 write multiple registers
(Note: reverse word order in double word format)
3xbit is equivalent to 3x
4xbit is equivalent to 4x
6x 0x03 Read holding register 0x06 write single register
(Note: 6x is limited to device of one word only)

344
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
MODBUS RTU CONTROLLER : RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female FeMale
2 RX 8 RX TXD
3 TX 7 TX RXD
5 GND 5 GND GND
RTS
circuit
CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male FeMale
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND
RTS
circuit
CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub
D-Sub Female FeMale
9 RX TXD
6 TX RXD
5 GND GND
RTS
circuit
CTS

345
PLC Connection Guide

The following represents the cable end connector.

MODBUS RTU CONTROLLER : RS485 4W
eMT3000 series
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Female Female
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

346
PLC Connection Guide
The following represents the cable end connector.
MODBUS RTU CONTROLLER : RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Female
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND GND

Driver Version:
Version Date Description
Fixed when receiving data over 8 bytes from MODBUS RTU,
V1.90 May/05/2010
LW-9570 fails to calculate correctly.

347
PLC Connection Guide

MODBUS RTU (0x/1x Range Adjustable)

Supported Series : MODBUS RTU CONTROLLER
Website : http://www.modbus.org

HMI Setting:
Parameters Recommended Options Notes
PLC type MODBUS RTU (0x/1x Range Adjustable)
PLC I/F RS485 RS232/RS485
Baud rate 9600 9600~115200
Data bits 8 7,8
Parity Even Even, Odd, None
Stop bits 1 1,2
PLC sta. no. 1 0-255

Online simulator YES

Extend address mode YES

PLC Setting:
Communication mode Modbus RTU protocol

348
PLC Connection Guide

NOTE:
Address type “5x” is mapping to Hold Reg. The communication protocol of “5x” is almost
the same as “4x” except that “5x” swaps double words.
If 4x contains the following information:
Address 1 2 3 4 5 6 ...
Data in 0x1 0x2 0x3 0x4 0x5 0x6
word
Data 0x20001 0x40003 0x60005

For 5x, it will be:

Address 1 2 3 4 5 6 ...
Data in 0x2 0x1 0x4 0x3 0x6 0x5
word
Data 0x10002 0x30004 0x50006

Modbus RTU function code:

0x 0x01 Read coil 0x05 Write single coil
0x_multi_coils 0x01 Read coil 0x0f Write multiple coils
1x 0x02 Read discrete input N/A for writing operation
3x 0x04 Read input register N/A for writing operation
4x 0x03 Read holding register 0x10 Write multiple registers
5x 0x03 Read holding register 0x10 Write multiple registers
(Note: reverse word order in double words format)
3xbit is equivalent to 3x
4xbit is equivalent to 4x
6x 0x03 Read holding register 0x06 Write single register
(Note: 6x is limited to device of one word only)

349
PLC Connection Guide

Setting Instructions:

1. Go to [System Parameter Settings] ，click [New] to add a new device -Modbus

RTU (0x 1x range adjustable)，as shown below:

2. After adding Modbus RTU (0x 1x Range Adjustable) driver, [Add Address Range Limit]
button will be enabled as below. Users can set maximum read/write command size
here.

 Max.read-command size (words): Pull down to select PLC reading range.

 Max.write-command size (words): Pull down to select PLC writing range.

Note: Setting [Add Address Range Limit] is enabled only when bit address is not a multiple
of 16bit.

350
PLC Connection Guide

3. Click [Add Address Range Limit] button, Users can define 0x and 1x address range in
[0x 1x Address Range] dialog box, referring to bit range of the device used.

351
PLC Connection Guide
Add：Set [Station No.], [Device Type], [Min. Address], [Max. Address] then click [OK] to
finish adding as below:

Delete：The selected items will be deleted.

Settings：Set [Station No.], [Device Type], [Min. Address], [Max. Address] then click [OK]
to finish adding as below:

Example：
Take D2 and D8 of SCON as example, the settings depend on bit range of different PLC
types. Set [Station No.] and address first.
For D2, set [Station No.] to 20, [Device Type] 0x, [Max. Address] 36.
For D8, set [Station No.] to 2, [Device Type] 0x, [Max. Address] 51.

352
PLC Connection Guide

Note: If communicating with a RS-485 2W PLC, the [Turn around delay] setting may need
to be adjusted according to the reply speed of the device. Please click [Settings] in [Device
Properties], and set the [Turn around delay (ms)] parameter as shown:

After completing all settings above, the communication is enabled.

353
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
MODBUS RTU CONTROLLER : RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female Female
2 RX 8 RX TXD
3 TX 7 TX RXD
5 GND 5 GND GND
RTS
circuit
CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Female
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND
RTS
circuit
CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub
D-Sub Female Female
9 RX TXD
6 TX RXD
5 GND GND
RTS
circuit
CTS

354
PLC Connection Guide
The following represents the cable end connector.
MODBUS RTU CONTROLLER : RS485 4W
eMT3000 series
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Female Female
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

355
PLC Connection Guide
The following represents the cable end connector.
MODBUS RTU CONTROLLER : RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Female
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND GND

Driver Version:
Version Date Description
V1.10 Aug/25/2010
V1.20 Mar/2/2012 Allow modifying the Minimum address of 0x、1x Address Range.

356
PLC Connection Guide

MODBUS RTU (Adjustable)

Supported Series : MODBUS RTU CONTROLLER
Website : http://www.modbus.org

HMI Setting:
Parameters Recommended Options Notes
PLC type MODBUS RTU (Adjustable)
PLC I/F RS485 RS232/RS485
9600/19200/3840
Baud rate 9600
0/57600/115200
Data bits 8 7,8
Parity Even Even, Odd, None
Stop bits 1 1,2
PLC sta. no. 1 0-255

Online simulator YES

Extend address mode YES

PLC Setting:
Communication mode Modbus RTU protocol

Device Address:
Bit/Word Device type Format Range Memo
B 0x DDDDD 1 ~ 65535 Output bit
B 1x DDDDD 1 ~ 65535 Input bit (read only)
B 3x_Bit DDDDDdd 100 ~ 6553515 Input Register bit (read only)
B 4x_Bit DDDDDdd 100 ~ 6553515 Output Register bit
B 0x_multi_coils DDDDD 1 ~ 65535 Write multiple coils
W 3x DDDDD 1 ~ 65535 Input Register (read only)
W 4x DDDDD 1 ~ 65535 Output Register
W 5x DDDDD 1 ~ 65535 4x double word swap
DW 5x (32-bit) DDDDD 1 ~ 65535 4x double word
W 6x DDDDD 1 ~ 65535 4x single word write

357
PLC Connection Guide

For 5x, it will be:

Address 1 2 3 4 5 6 ...
Data in 0x2 0x1 0x4 0x3 0x6 0x5
word
Data 0x10002 0x30004 0x50006

Modbus RTU function code:

358
PLC Connection Guide

Setting Instructions:

1. Go to [System Parameter Settings] ，click [New] to add a new device - MODBUS

RTU (Adjustable)，as shown below:

2. After adding MODBUS RTU (Adjustable) driver, [Add Address Range Limit] button will
be enabled as below. Users can set maximum read/write command size here.

 Max.read-command size (words): Pull down to select PLC reading range.

 Max.write-command size (words): Pull down to select PLC writing range.

359
PLC Connection Guide

Note:
MODBUS RTU (adjustable) usage
Users can decide the address range via setting value on Parameter 1. For example, when
users set 5 to Parameter 1, the address range will be 5 ~ 65535.

360
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
MODBUS RTU CONTROLLER : RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female Female
2 RX 8 RX TXD
3 TX 7 TX RXD
5 GND 5 GND GND
RTS
circuit
CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Female
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND
RTS
circuit
CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub
D-Sub Female Female
9 RX TXD
6 TX RXD
5 GND GND
RTS
circuit
CTS

361
PLC Connection Guide
The following represents the cable end connector.
MODBUS RTU CONTROLLER : RS485 4W
eMT3000 series
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Female Female
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

362
PLC Connection Guide
The following represents the cable end connector.
MODBUS RTU CONTROLLER : RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Female
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND GND

Driver Version:
Version Date Description
V1.40 Jun/14/2011

363
PLC Connection Guide

MODBUS RTU (zero-based addressing)

Supported Series : MODBUS RTU CONTROLLER

Website : http://www.modbus.org

HMI Setting:
Parameters Recommended Options Notes
PLC type MODBUS RTU (zero-based addressing)
PLC I/F RS485 RS232/RS485
Baud rate 9600 9600~115200
Data bits 8 7,8
Parity Even Even, Odd, None
Stop bits 1 1,2
PLC sta. no. 1 0-255

Online simulator YES Broadcast command YES

Extend address mode YES

PLC Setting:
Communication mode Modbus RTU protocol

Device Address:
Bit/Word Device type Format Range Memo
B 0x DDDDD 0 ~ 65535 Output bit
B 1x DDDDD 0 ~ 65535 Input bit (read only)
B 3x_Bit DDDDDdd 0 ~ 6553515 Input Register bit (read only)
B 4x_Bit DDDDDdd 0 ~ 6553515 Output Register bit
B 0x_multi_coils DDDDD 0 ~ 65535 Write multiple coils
W 3x DDDDD 0 ~ 65535 Input Register (read only)
W 4x DDDDD 0 ~ 65535 Output Register
DW 5x DDDDD 0 ~ 65535 4x double word swap
W 6x DDDDD 0 ~ 65535 4x single word write

364
PLC Connection Guide

NOTE:
Address type “5x” is mapping to Hold Reg. The communication protocol of 5x is almost the
same as “4x” except that “5x” swaps double words.
If 4x contains the following information:
Address 1 2 3 4 5 6 ...
Data in word 0x1 0x2 0x3 0x4 0x5 0x6
Data 0x20001 0x40003 0x60005

For 5x, it will be:

Address 1 2 3 4 5 6 ...
Data in word 0x2 0x1 0x4 0x3 0x6 0x5
Data 0x10002 0x30004 0x50006

Modbus RTU function code:

365
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
MODBUS RTU CONTROLLER : RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female Female
2 RX 8 RX TXD
3 TX 7 TX RXD
5 GND 5 GND GND
RTS
circuit
CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Female
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND
RTS
circuit
CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub
D-Sub Female Female
9 RX TXD
6 TX RXD
5 GND GND
RTS
circuit
CTS

366
PLC Connection Guide
The following represents the cable end connector.
MODBUS RTU CONTROLLER : RS485 4W
eMT3000 series
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Female Female
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

367
PLC Connection Guide
The following represents the cable end connector.
MODBUS RTU CONTROLLER : RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Female
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND GND

Driver Version:
Version Date Description
V1.30 Aug/26/2009

368
PLC Connection Guide

MODBUS Server (COM/Ethernet)

HMI Setting:
Parameters Recommended Options Notes
PLC type MODBUS Server (COM/Ethernet)
PLC I/F RS232 RS232, RS485
9600~115200 Ethernet supports UDP or TCP/IP
Baud rate 9600
Ethernet protocol
Data bits 8 8
Parity Even Even, Odd,
Stop bits 1 None
1
PLC sta. no. 1 1-31 HMI Modbus Station No.
Port no. 502

Online simulator YES Extend address mode NO

Broadcast command NO

PLC Setting:
Communication mode Modbus RTU protocol

Modbus Server UDP Protocol Setting:

MODBUS Server (Ethernet) supports UDP communication protocol. To use UDP mode,
go to [System Parameter Settings] in editing software, in [Device list] click [New], for [PLC
type] select “Modbus Server”, [PLC I/F] set to [Ethernet], and select [Use UDP (User
Datagram Protocol)] to finish setting.

369
PLC Connection Guide

Modbus Server Port No. can be changed by clicking [Settings].

Modbus Server Port No. can not be set identically to HMI Port No. When doing so, the
warning message below will be shown requesting users to change setting.

Note:
A maximum of 64 Clients can be connected simultaneously.
Modbus Server Port No. can’t be identical to HMI Port No.

370
PLC Connection Guide

Modbus Server TCP/IP Protocol Setting:

MODBUS Server (Ethernet) supports TCP/IP communication protocol. Go to [System
Parameter Settings] in editing software, in [Device list] click [New], for [PLC type] select
“Modbus Server”, [PLC I/F] set to [Ethernet] to finish setting.

For Modbus Server TCP/IP, HMI Port No. is the same as Modbus Server Port No. To
change Prot No. go to [System Parameter Settings] / [Model], the default Port No. is
“8000”, and it is allowed to change Modbus Server Port No. here.

371
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
B LB dddd 0 ~ 9998 Mapping to 0x/1x 1 ~ 9999
W LW dddd 0 ~ 9998 Mapping to 3x/4x 1 ~ 9999
W RW ddddd 0 ~ 55536 Mapping to 3x/4x 10000 ~ 65536

LB0 = 0x0001, LB1 = 0x0002, LW0 = 3x0001, LW1 = 3x0002

Modbus RTU Server doesn’t support function code 06(preset single register), please use
function code 16(0x10, preset multiple registers).

Modbus Server Function Code:

Wiring Diagram:
The following represents the cable end connector.
MODBUS SERVER : RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female Female
2 RX 8 RX TXD
3 TX 7 TX RXD
5 GND 5 GND GND
RTS
circuit
CTS

372
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Female
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND
RTS
circuit
CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub
D-Sub Female Female
9 RX TXD
6 TX RXD
5 GND GND
RTS
circuit
CTS

The following represents the cable end connector.

MODBUS SERVER : RS485 4W
eMT3000 series
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

373
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Female Female
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

The following represents the cable end connector.

MODBUS SERVER : RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

374
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND GND

MODBUS SERVER : Ethernet

Direct connect (crossover cable):
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 3 RX+
2 TX- Orange 6 RX-
3 RX+ White/Green 1 TX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 2 TX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

375
PLC Connection Guide
Through a hub:
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 1 TX+
2 TX- Orange 2 TX-
3 RX+ White/Green 3 RX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 6 RX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Note: Setting more than one Modbus Server in HMI Device List is of no effect.

Driver Version:
Version Date Description
V1.00 Dec/30/2008 Driver released

376
PLC Connection Guide

MODBUS TCP/IP
Supported Series: Modbus RTU TCP/IP device.

Website: http://www.modbus.org

HMI Setting:
Parameters Recommended Options Notes
PLC type MODBUS TCP/IP
PLC I/F Ethernet
Port no. 502
PLC sta. no. 1 0~255

Device Address:
Bit/Word Device type Format Range Memo
B 0x DDDDD 1 ~ 65535 Input bit
B 1x DDDDD 1 ~ 65535 Output bit
B 3x_bit DDDDDdd 100 ~ 6553515 Input Register bit(read only)
B 4x_bit DDDDDdd 100 ~ 6553515 Output Register bit
B 6x_bit DDDDDdd 100 ~ 6553515 Output Register bit
B 0x_multi_coils DDDDD 1 ~ 65535 Write multiple coils
W 3x DDDDD 1 ~ 65535 Input Register
W 4x DDDDD 1 ~ 65535 Output Register
DW 5x DDDDD 1 ~ 65535 4x double word swap
W 6x DDDDD 1 ~ 65535 4x single word write
4x string
W central DDDDD 1 ~ 65535
europe rev

377
PLC Connection Guide

Driver Version:
Version Date Description
V1.50 Aug/26/2009

378
PLC Connection Guide

MODBUS TCP/IP (0x/1x Range Adjustable)

Supported Series : Modbus RTU TCP/IP device.
Website : http://www.modbus.org

HMI Setting:
Parameters Recommended Options Notes
PLC type MODBUS TCP/IP (0x/1x Range Adjustable)
PLC I/F Ethernet
Port no. 502
PLC sta. no. 1 0~255

Online simulator YES

Extend address mode YES

379
PLC Connection Guide

For 5x, it will be:

Address 1 2 3 4 5 6 ...
Data in 0x2 0x1 0x4 0x3 0x6 0x5
word
Data 0x10002 0x30004 0x50006

Modbus RTU function code:

380
PLC Connection Guide

Setting Instructions:

1. Go to [System Parameter Settings] ，click [New] to add a new device -MODBUS

TCP/IP (0x/1x Range Adjustable)，as shown below:

2. Click [Add Address Range Limit] button, Users can define 0x and 1x address range in
[0x 1x Address Range] dialog box, referring to bit range of the device used.

381
PLC Connection Guide

Add：Set [Station No.], [Device Type], [Max. Address] then click [OK] to finish adding as
below:

Delete：The selected items will be deleted.

Settings：Set [Station No.], [Device Type], [Max. Address] then click [OK] to finish adding
as below:

382
PLC Connection Guide
Example：
Take 0x and 1x as example, the settings depend on bit range of different PLC types.
For 0x, [Device Type] 0x, [Min. Address]5,[Max. Address] 20.
For 1x, [Device Type] 0x, [Min. Address]1,[Max. Address] 10.

After completing all settings above, the communication is enabled.

383
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 NOV/2/2011 Driver released.
V1.10 MAR/14/2012 Allow modifying the Minimum address of 0x、1x Address Range.

384
PLC Connection Guide

MODBUS TCP/IP (zero-based addressing)

Supported Series : Modbus RTU TCP/IP device.

Website: http://www.modbus.org

HMI Setting:
Parameters Recommended Options Notes
PLC type MODBUS TCP/IP (zero-based addressing)
PLC I/F Ethernet
Port no. 502
PLC sta. no. 1 0~255

Device Address:
Bit/Word Device type Format Range Memo
B 0x DDDDD 0 ~ 65535 Input bit
B 1x DDDDD 0 ~ 65535 Output bit
B 3x_Bit DDDDDdd 0 ~ 6553515 Input Register bit (read only)
B 4x_Bit DDDDDdd 0 ~ 6553515 Output Register bit
B 6x_Bit DDDDDdd 0 ~ 6553515 Output Register bit
B 0x_multi_coils DDDDD 0 ~ 65535 Write multiple coils
W 3x DDDDD 0 ~ 65535 Input Register
W 4x DDDDD 0 ~ 65535 Output Register
DW 5x DDDDD 0 ~ 65535 4x double word swap
W 6x DDDDD 0 ~ 65535 4x single word write

385
PLC Connection Guide

Driver Version:
Version Date Description
V1.40 Aug/27/2009

386
PLC Connection Guide

MODBUS TCP/IP 32Bit

Supported Series: Modbus RTU TCP/IP device.

Website: http://www.modbus.org

HMI Setting:
Parameters Recommended Options Notes
PLC type MODBUS TCP/IP 32Bit
PLC I/F Ethernet
Port no. 502
PLC sta. no. 1 0~255

Device Address:
Bit/Word Device type Format Range Memo
B 0x DDDDD 1 ~ 65535 Input bit
B 1x DDDDD 1 ~ 65535 Output bit
B 3x_Bit DDDDDdd 100 ~ 6553515 Input Register bit (read only)
B 4x_Bit DDDDDdd 100 ~ 6553515 Output Register bit
B 6x_Bit DDDDDdd 100 ~ 6553515 Output Register bit
B 0x_multi_coils DDDDD 1 ~ 65535 Write multiple coils
W 3x DDDDD 1 ~ 65535 Input Register
W 4x DDDDD 1 ~ 65535 Output Register
DW 5x DDDDD 1 ~ 65535 4x double word swap
W 6x DDDDD 1 ~ 65535 4x single word write
W 4x_32Bit* DDDDD 1 ~ 65535
4x_32Bit will only read / write 2 words for each package, for continuous addresses, it will
be divided into several packages.

387
PLC Connection Guide

Driver Version:
Version Date Description
V1.10 Aug/27/2009 Driver released.

388
PLC Connection Guide

Moeller XC-CPU101
Supported Series: MOELLER XC100/200 series

Website: http://www.moeller.net

HMI Setting:
Parameters Recommended Options Notes
PLC type Moeller XC-CPU101
PLC I/F RS232
Baud rate 38400 4800 ~ 57600
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Note
B QX DDo 0 ~ 157
B IX DDo 0 ~ 157
W MW DDDD 0 ~ 4095
W QW DD 0 ~ 15
W IW DD 0 ~ 15

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 8P RJ45 Male
D-Sub Female D-Sub Female
2 RX 8 RX 5 TD
3 TX 7 TX 8 RD
5 GND 5 GND 4 GND

389
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 8P RJ45 Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 5 TD
3 TX 4 TX 7 TX 8 RD
5 GND 5 GND 5 GND 4 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 8P RJ45 Male
D-Sub Female
9 RX 5 TD
6 TX 8 RD
5 GND 4 GND

Driver Version:
Version Date Description
1.00 Apr/01/2010 Driver released.

390
PLC Connection Guide

OHJX

Website: http://www.ohjx.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type OHJX
PLC I/F RS-232
Baud rate 9600 9600,19200
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
B R100 Dh 0 ~ 1f
B R101 Dh 0 ~ 1f
B R102 Dh 0 ~ 1f
B R103 Dh 0 ~ 1f
B R104 Dh 0 ~ 1f
B R105 Dh 0 ~ 1f
B R106 Dh 0 ~ 1f
B R107 Dh 0 ~ 1f
B R108 Dh 0 ~ 1f
B R109 Dh 0 ~ 1f
B R110 Dh 0 ~ 1f
B R210 Dh 0 ~ 1f
B R310 Dh 0 ~ 1f
W SV DDDD 0 ~ 9999
W EV DDDDD 0 ~ 65535
W DT DDDDD 0 ~ 9999
W LD DDDD 0 ~ 8447
W WX DDDD 0 ~ 9999

391
PLC Connection Guide
Bit/Word Device type Format Range Memo
W WY DDDD 0 ~ 9999
W WR DDDD 0 ~ 9999
W WL DDDD 0 ~ 9999
W FL DDDDD 0 ~ 99999

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P 4P Mini-DIN Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TX
3 TX 7 TX 2 RX
5 GND 5 GND 1 GND
circuit
4 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P 4P Mini-DIN Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TX
3 TX 4 TX 7 TX 2 RX
5 GND 5 GND 5 GND 1 GND
circuit
4 GND

392
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P 4P Mini-DIN Male
D-Sub Female
9 RX 3 TX
6 TX 2 RX
5 GND 1 GND
circuit
4 GND

Driver Version:
Version Date Description
V1.00 Nov/22/2011 Driver released.

393
PLC Connection Guide

OMRON C/CQM1 Series

Supported Series: OMRON C, CPM, CPL, CQM Series (Host Link Protocol)
Website: http://oeiweb.omron.com/oei/Products-PLC.htm

HMI Setting:
Parameters Recommended Options Notes
PLC type OMRON C/CQM1 Series
PLC I/F RS232 RS232, RS422, RS485
Baud rate 9600 9600, 19200
Data bits 7 7 or 8
Parity Even Even, Odd, None
Stop bits 2 1 or 2
PLC sta. no. 0 0-31 Host Link Station No.

Online simulator YES Broadcast command YES

Extend address mode YES

PLC Setting:
Communication mode Host Link Protocol

Device Address:
Bit/Word Device type Format Range Memo
B IR DDDDdd 0 ~ 409515 I/O and Internal Relay
B HR DDDDdd 0 ~ 409515 Hold Relay
B LR DDDDdd 0 ~ 409515 Link Relay
B IR (Force Set/Reset) DDDDdd 0 ~ 409515
B HR (Force Set/Reset) DDDDdd 0 ~ 409515
B LR (Force Set/Reset) DDDDdd 0 ~ 409515
B AR DDDDdd 0 ~ 409515 Auxiliary Relay
W AR_W DDDD 0 ~ 4095
W IR_W DDDD 0 ~ 4095
W HR_W DDDD 0 ~ 4095
W LR_W DDDD 0 ~ 4095
W TC DDD 0 ~ 255
W DM DDDD 0 ~ 9999 Data Register

394
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
CPU Port (CPM2A,CQM1/1H,C200H/HS/ALPHA series)
Communication Module:
CPM1-CIF01 adapter (for CPM1/CPM1A/CPM2A series, CQM1/CQM1H series)
CPM1H-SCB41 communication module (for CQM1H-CPU51/61)
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 2 SD
3 TX 7 TX 3 RD
5 GND 5 GND 9 GND
4 RS
circuit
5 CS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 2 SD
3 TX 4 TX 7 TX 3 RD
5 GND 5 GND 5 GND 9 GND
4 RS
circuit
5 CS

395
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 2 SD
6 TX 3 RD
5 GND 9 GND
4 RS
circuit
5 CS

The following represents the cable end connector.

C200h-LK201,3G2A6-LK201 communication module
C200HW-COM02/03/04/05/06 communication module
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 2 SD
3 TX 7 TX 3 RD
5 GND 5 GND 7 GND
4 RS
circuit
5 CS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 2 SD
3 TX 4 TX 7 TX 3 RD
5 GND 5 GND 5 GND 7 GND
4 RS
circuit
5 CS

396
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 2 SD
6 TX 3 RD
5 GND 7 GND
4 RS
circuit
5 CS

Driver Version:
Version Date Description
V1.80 Apr/14/2010

397
PLC Connection Guide

OMRON CJ/CS/CP
Supported Series: OMRON CP1L, CP1H, CJ1M, CJ2M, CJ1H, CJM1G, CS1H and CS1G.
(Host Link Protocol FINS command), this driver supports Extend Addressing Mode.

Website: http://oeiweb.omron.com/oei/Products-PLC.htm

HMI Setting:
Parameters Recommended Options Notes
PLC type OMRON CJ/CS/CP
PLC I/F RS232 RS232, RS422, RS485
Baud rate 9600 9600~115200
Data bits 7 7 or 8
Parity Even Even, Odd, None
Stop bits 2 1 or 2
PLC sta. no. 0 0-31 Host Link Station No.

Online simulator YES Extend address mode YES

Broadcast command NO

PLC Setting:
Communication mode Host Link Protocol

Device Address:
Bit/Word Device type Format Range Memo
B CIO_Bit DDDDDdd 0 ~ 3276715 Channel I/O (CIO)
B W_Bit DDDDDdd 0 ~ 3276715 Work Area (WR)
B H_Bit DDDDDdd 0 ~ 3276715 Holding Area (HR)
B D_Bit DDDDDdd 0 ~ 3276715 Data Memory (DM)
B A_Bit DDDDDdd 0 ~ 3276715 Auxiliary Relay (AR)
B T_Bit DDDDDdd 0 ~ 3276715 Timer (TIM)
B C_Bit DDDDDdd 0 ~ 3276715 Counter (CNT)
B C_flag DDDD 0 ~ 4095
B T_flag DDDD 0 ~ 4095
B LR_Bit DDDdd 0 ~ 19915
398
PLC Connection Guide
Bit/Word Device type Format Range Memo
W T DDDDD 0 ~ 32767 Timer (TIM)
W H DDDDD 0 ~ 32767 Holding Area (HR)
W D DDDDD 0 ~ 32767 Data Memory (DM)
W A DDDDD 0 ~ 32767 Auxiliary Relay (AR)
W W DDDDD 0 ~ 32767 Work Area (WR)
W C DDDDD 0 ~ 32767 Counter (CNT)
W CIO DDDDD 0 ~ 32767 Channel I/O (CIO)
W EM0 ~ EMC DDDDD 0 ~ 32767 Extend Memory
W LR DDD 0 ~ 199

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 2 SD
3 TX 4 TX 7 TX 3 RD
5 GND 5 GND 5 GND 9 GND
4 RS
circuit
5 CS

399
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 2 SD
6 TX 3 RD
5 GND 9 GND
4 RS
circuit
5 CS

The following represents the cable end connector.

CP1H/CP1L CP1W-CIF11 RS485 4W : 9P D-Sub to Termainals:
eMT3000 series
COM1 RS485 4W CP1W-CIF11 RS485
9P D-Sub Male 4W Terminal
1 RX- SDA
2 RX+ SDB
3 TX- RDA
4 TX+ RDB
5 GND FG

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W CP1W-CIF11 RS485
9P D-Sub Male 4W Terminal
1 RX- SDA
2 RX+ SDB
3 TX- RDA
4 TX+ RDB
5 GND FG

400
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W CP1W-CIF11 RS485
9P D-Sub Female 4W Terminal
1 RX- SDA
2 RX+ SDB
3 TX- RDA
4 TX+ RDB
5 GND FG

CP1W-CIF11: SW1 ON, others OFF.

Driver Version:
Version Date Description
V1.90 Feb/01/2011 Added registers: LR, LR_Bit

401
PLC Connection Guide

OMRON CJ1/CS1 (Ethernet)

Supported Series: OMRON CJ Series, CS Series, CP Series +Ethernet Module. (Ethernet
FINS)
Website: http://oeiweb.omron.com/oei/Products-PLC.htm
*On initialization, switch from RUN MODE to MONITOR MODE.

HMI Setting:
Parameters Recommended Options Notes
PLC type OMRON CJ1/CS1 (Ethernet)
PLC I/F Ethernet
Port no. 9600
PLC sta. no. 0

PLC Setting:
Communication mode FINS Ethernet protocol

Device Address:
Bit/Word Device type Format Range Memo
B CIO_Bit DDDDDdd 0 ~ 3276715 Channel I/O (CIO)
B W_Bit DDDDDdd 0 ~ 3276715 Work Area (WR)
B H_Bit DDDDDdd 0 ~ 3276715 Holding Area (HR)
B A_Bit DDDDDdd 0 ~ 3276715 Auxiliary Relay (AR) (Read only)
B D_Bit DDDDDdd 0 ~ 3276715 Data Memory (DM)
B T_Bit DDDDDdd 0 ~ 3276715 Timer (TIM)
B C_Bit DDDDDdd 0 ~ 3276715 Counter (CNT)
B C_Flag DDDD 0 ~ 4095
B T_Flag DDDD 0 ~ 4095
W CIO DDDDD 0 ~ 32767 Channel I/O (CIO)
W W DDDDD 0 ~ 32767 Work Area (WR)
W H DDDDD 0 ~ 32767 Holding Area (HR)
W A DDDDD 0 ~ 32767 Auxiliary Relay (AR) (Read only)
W C DDDDD 0 ~ 32767 Counter (CNT)
W T DDDDD 0 ~ 32767 Timer (TIM)
W D DDDDD 0 ~ 32767 Data Memory (DM)
W EM0 ~ EMC DDDDD 0 ~ 32767 Extend Memory

402
PLC Connection Guide

Driver Version:
Version Date Description
V1.50 Jun/30/2010

403
PLC Connection Guide

OMRON E5CN/E5EZ/E5ZN
Supported Series: OMRON E5CN series temperature controller with communication
options. E5EN/CN/GN/EZ/ZN series.

Website: http://oeiweb.omron.com

HMI Setting:
Parameters Recommended Options Notes
PLC type OMRON E5CN
PLC I/F RS485 2W
9600/19200/38400/
Baud rate 9600
57600/115200
Data bits 7 7,8
Parity Even Even, Odd, None
Stop bits 2 1,2
PLC sta. no. 0 0-99

Online simulator YES Broadcast command YES

Extend address mode YES

Device Address:
Bit/Word Device type Format Range Memo
B Status_CH1 DD 0 ~ 31 Page40
B Status_CH2 DD 0 ~ 31
DW C0 HHHH 0 ~ 270f Read only (Hex) Page34
DW C1 HHHH 0 ~ 270f Read/Write (Hex) Page35
DW C2 HHHH 0 ~ 270f Read/Write (Hex) Page35
DW C3 HHHH 0 ~ 270f Read/Write (Hex) Page36
W Code00_00 H 0 Communications writing OFF (disabled)
W Code00_01 H 0 Communications writing ON(enabled)
W Code01_00 H 0 Run
W Code01_01 H 0 Stop
W Code02_00 H 0 Multi-SP Set point 0
W Code02_01 H 0 Multi-SP Set point 1
W Code02_02 H 0 Multi-SP Set point 2

404
PLC Connection Guide

Bit/Word Device type Format Range Memo

W Code02_03 H 0 Multi-SP Set point 3
W Code03_00 H 0 AT cancel
W Code03_01 H 0 AT execute
W Code04_00 H 0 Write mode (Backup)
W Code04_01 H 0 Write mode (Ram)
W Code05_00 H 0 Save RAM data
W Code06_00 H 0 Software reset
W Code07_00 H 0 Move to setup area 1
W Code08_00 H 0 Move to protect level
W Code01_10 H 0
W Code01_11 H 0
W Code01_F0 H 0
W Code01_F1 H 0
W Code02_10 H 0
W Code02_11 H 0
W Code02_F0 H 0
W Code02_F1 H 0
W Code03_10 H 0
W Code03_11 H 0
W Code03_F0 H 0
W Code03_F1 H 0
W Code09_00 H 0
W Code09_01 H 0
W Code09_10 H 0
W Code09_11 H 0
W Code09_F0 H 0
W Code09_F1 H 0
W Code0A_00 H 0
W Code0B_00 H 0
W Code0C_00 H 0
W Code0C_01 H 0
W Code0C_02 H 0
W Code0C_0F H 0
W Code0C_10 H 0
W Code0C_11 H 0
W Code0C_12 H 0
W Code0C_1F H 0
W Code0C_F0 H 0
W Code0C_F1 H 0
W Code0C_F2 H 0

405
PLC Connection Guide

Bit/Word Device type Format Range Memo

W Code0C_FF H 0

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W OMRON E5CN
9P D-Sub Male 9P D-Sub Male Terminal
1 RX- 6 Data- 12 B
2 RX+ 9 Data+ 11 A
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W OMRON E5CN
9P D-Sub Male 9P D-Sub Male Terminal
1 RX- 6 Data- 12 B
2 RX+ 9 Data+ 11 A
5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W OMRON E5CN
9P D-Sub Female 9P D-Sub Female Terminal
1 RX- 7 Data- 12 B
2 RX+ 8 Data+ 11 A
5 GND 5 GND GND

Note:
For communication with OMRON E5EZ, please set communication settings to 9600, E, 7,
2, station no. 1.
406
PLC Connection Guide

Driver Version:
Version Date Description
V1.21 Dec/21/2010

407
PLC Connection Guide

OMRON FINS (Ethernet)

Supported Series: Non OMRON PLC . (Ethernet FINS)

HMI Setting:
Parameters Recommended Options Notes
PLC type OMRON FINS (Ethernet)
PLC I/F Ethernet
Port no. 9600
PLC sta. no. 0

PLC Setting:
Communication mode FINS Ethernet protocol

Device Address:
Bit/Word Device type Format Range Memo
B CIO_Bit DDDDDdd 0 ~ 3276715 Channel I/O (CIO)
B W_Bit DDDDDdd 0 ~ 3276715 Work Area (WR)
B H_Bit DDDDDdd 0 ~ 3276715 Holding Area (HR)
B A_Bit DDDDDdd 0 ~ 3276715 Auxiliary Relay (AR) (Read only)
B D_Bit DDDDDdd 0 ~ 3276715 Data Memory (DM)
B T_Bit DDDDDdd 0 ~ 3276715 Timer (TIM)
B C_Bit DDDDDdd 0 ~ 3276715 Counter (CNT)
B C_Flag DDDD 0 ~ 4095
B T_Flag DDDD 0 ~ 4095
W CIO DDDDD 0 ~ 32767 Channel I/O (CIO)
W W DDDDD 0 ~ 32767 Work Area (WR)
W H DDDDD 0 ~ 32767 Holding Area (HR)
W A DDDDD 0 ~ 32767 Auxiliary Relay (AR) (Read only)
W C DDDDD 0 ~ 32767 Counter (CNT)
W T DDDDD 0 ~ 32767 Timer (TIM)
W D DDDDD 0 ~ 32767 Data Memory (DM)
W EM0 ~ EMC DDDDD 0 ~ 32767 Extend Memory

408
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 May/26/2011 Driver released.

409
PLC Connection Guide

OMRON Host Link

Supported Series: OMRON C, CPM, CPL, CQM Series (Host Link Protocol)
Website: http://oeiweb.omron.com/oei/Products-PLC.htm

HMI Setting:
Parameters Recommended Options Notes
PLC type OMRON Host Link
PLC I/F RS232 RS232, RS422, RS485
Baud rate 9600 9600, 19200
Data bits 7 7 or 8
Parity Even Even, Odd, None
Stop bits 2 1 or 2
PLC sta. no. 0 0-31 Host Link Station No.

Online simulator YES Broadcast command YES

Extend address mode YES

PLC Setting:
Communication mode Host Link Protocol

410
PLC Connection Guide

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 2 SD
3 TX 4 TX 7 TX 3 RD
5 GND 5 GND 5 GND 9 GND
4 RS
circuit
5 CS

411
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 2 SD
6 TX 3 RD
5 GND 9 GND
4 RS
circuit
5 CS

The following represents the cable end connector.

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 2 SD
3 TX 4 TX 7 TX 3 RD
5 GND 5 GND 5 GND 7 GND
4 RS
circuit
5 CS

412
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 2 SD
6 TX 3 RD
5 GND 7 GND
4 RS
circuit
5 CS

Driver Version:
Version Date Description
V1.30 OCT/21/2010

413
PLC Connection Guide

Panasonic FP
Supported Series: NAIS (Matsushita) FP series include FP-X, FP-Σ, FP0, FP1, FP2,
FP2SH, FP10SH and FP3 Ethernet support FP-X with AFPX-COM5.

Website:http://pewa.panasonic.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Panasonic FP
PLC I/F RS232 RS232/RS485
Baud rate 9600 9600, 19200, 38400,
Data bits 8 57600,
7 or 8 115200
Parity Odd Even, Odd, None
Stop bits 1 1 or 2
Must match the PLC port
PLC sta. no. 1 0-255 setting.
FP3 must set to 0.

Device Address:
Bit/Word Device type Format Range Memo
B X DDDDh 0 ~ 9999f Input (X)
B Y DDDDh 0 ~ 9999f Output (Y)
B R DDDDh 0 ~ 9999f Internal Relay (R)
B L DDDD 0 ~ 9999 Link Relay (L)
B L_Bit DDDDh 0 ~ 9999f
B T DDDD 0 ~ 9999 Timer (T)
B C DDDD 0 ~ 9999 Counter (C)
W SV DDDD 0 ~ 9999 Timer/Counter Set Value (SV)
W EV DDDDD 0 ~ 65535 Timer/Counter Elapse Value (EV)
W DT DDDDD 0 ~ 99999 Data Register (DT)
W LD DDDD 0 ~ 8447 Link Register (LD)
W WX DDDD 0 ~ 9999 Input (WX) (read only)
W WY DDDD 0 ~ 9999 Output (WY)
W WR DDDD 0 ~ 9999 Internal Relay (WR)
W WL DDDD 0 ~ 9999 Link Relay (WL)
W FL DDDDD 0 ~ 99999 File Register (FL)

414
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
FP0, FP2, FP2SH, FPM CPU : 9P D-Sub to 5P Mini-DIN
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 5P Mini-DIN
D-Sub Female D-Sub Female Male
2 RX 8 RX 2 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 1 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 5P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 2 TXD
3 TX 4 TX 7 TX 3 RXD
5 GND 5 GND 5 GND 1 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 5P Mini-DIN
D-Sub Female Male
9 RX 2 TXD
6 TX 3 RXD
5 GND 1 GND

415
PLC Connection Guide
The following represents the cable end connector.
FP0 CPU : 9P D-Sub to 3P Terminal:
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 3P Terminal
D-Sub Female D-Sub Female
2 RX 8 RX S
3 TX 7 TX R
5 GND 5 GND G

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 3P Terminal
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX S
3 TX 4 TX 7 TX R
5 GND 5 GND 5 GND G

MT6050i/MT8050i
COM1 RS232 9P RS232 3P Terminal
D-Sub Female
9 RX S
6 TX R
5 GND G

416
PLC Connection Guide
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 2 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 7 GND
4 RTS
circuit
5 CTS
8 CD
circuit
9 ER

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 2 TXD
3 TX 4 TX 7 TX 3 RXD
5 GND 5 GND 5 GND 7 GND
4 RTS
circuit
5 CTS
8 CD
circuit
9 ER

417
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 2 TXD
6 TX 3 RXD
5 GND 7 GND
4 RTS
circuit
5 CTS
8 CD
circuit
9 ER

The following represents the cable end connector.

FP1 CPU : 9P D-Sub to 8P MiniDIN
eMT3000 series
COM1 RS485 4W RS485 4W 8P Hirose
9P D-Sub Male Male
1 RX- 2 TXDA
2 RX+ 5 TXDB
3 TX- 3 RXDA
4 TX+ 6 RXDB
5 GND 1 GND

418
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 4W RS485 4W 8P Hirose
9P D-Sub Male Male
1 RX- 2 TXDA
2 RX+ 5 TXDB
3 TX- 3 RXDA
4 TX+ 6 RXDB
5 GND 1 GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 8P Hirose
9P D-Sub Female Male
1 RX- 2 TXDA
2 RX+ 5 TXDB
3 TX- 3 RXDA
4 TX+ 6 RXDB
5 GND 1 GND

419
PLC Connection Guide
The following represents the cable end connector.
FP3 CPU : 9P D-Sub to 15P D-Sub
eMT3000 series
COM1 RS485 4W RS485 4W 15P D-Sub
9P D-Sub Male Male
1 RX- 9 TXDA
2 RX+ 2 TXDB
3 TX- 10 RXDA
4 TX+ 3 RXDB
5 GND 7 GND
4 RTS+
circuit
5 CTS+
11 RTS-
circuit
12 CTS-

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 15P D-Sub
9P D-Sub Male Male
1 RX- 9 TXDA
2 RX+ 2 TXDB
3 TX- 10 RXDA
4 TX+ 3 RXDB
5 GND 7 GND
4 RTS+
circuit
5 CTS+
11 RTS-
circuit
12 CTS-

420
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W RS485 4W 15P D-Sub
9P D-Sub Female Male
1 RX- 9 TXDA
2 RX+ 2 TXDB
3 TX- 10 RXDA
4 TX+ 3 RXDB
5 GND 7 GND
4 RTS+
circuit
5 CTS+
11 RTS-
circuit
12 CTS-

Driver Version:
Version Date Description
V1.80 Apr/09/2010 Added registers: FL

421
PLC Connection Guide

Panasonic FP (Ethernet)
Supported Series: NAIS (Matsushita) FP series include FP-X, FP-Σ, FP0, FP1, FP2,
FP2SH, FP10SH and FP3 Ethernet support FP-X with AFPX-COM5.

Website: http://pewa.panasonic.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Panasonic FP (Ethernet)
PLC I/F Ethernet
Port no. 9094
PLC sta. no. 1 0~255

422
PLC Connection Guide

Ethernet Connection TCP Port: 9094

Ethernet RS232

MT8000 AFPX-COM5
FP-X

423
PLC Connection Guide

Driver Version:
Version Date Description
V1.80 Apr/12/2010

424
PLC Connection Guide

Panasonic FP2 (Ethernet)

Supported Series: NAIS (Matsushita) FP2 series include FP2, FP2SH, and FP10SH CPU.

Website: http://pewa.panasonic.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type Panasonic FP2 (Ethernet)
PLC I/F Ethernet
Port no. 8500
PLC sta. no. 2 0~255

425
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 Mar/11/2010 Driver released.

426
PLC Connection Guide

Panasonic MINAS A4
Supported Series: Panasonic MINAS A4 series Servo Drive.

HMI Setting:
Parameters Recommended Options Notes
PLC type Panasonic MINAS A4
PLC I/F RS232
Baud rate 9600
Data bits 8
Parity None
Stop bits 1
Axis no. 0 (master station only) 0 ~ F (slave)

Device Address:
Bit/Word Device type Format Range Memo
B Command 20 D 0~7 States (Note 3)
B Command 27 DD 0 ~ 31 Input Signal (Note 3)
B Command 28 DD 0 ~ 31 Output Signal (Note 3)
CPU Version (Numeric
W Command 01 D 0
format:16-bit Hex)
W Command 05 DD 0 ~ 11 Driver Version (ASCII / 12 words)
W Command 06 DD 0 ~ 11 Motor Version (ASCII / 12 words)
command pulse counter
W Command 21 D 0~1
(Numeric format: 32-bit Signed)
feedback pulse counter
W Command 22 D 0~1
(Numeric format: 32-bit Signed)
present speed
W Command 24 D 0
(Numeric format: 16-bit Unsigned)
present torque
W Command 25 D 0
(Numeric format: 16-bit Unsigned)
present deviation counter
W Command 26 D 0~1
(Numeric format: 32-bit Signed)
write parameter to EEPROM
W Command 84 D 0
(Note 1)

427
PLC Connection Guide
Bit/Word Device type Format Range Memo
present Alarm Data
W Command 90 D 0
(Numeric format: 16-bit Unsigned)
Alarm History (Note 4)
W Command 91 DD 1 ~ 14
(Numeric format: 16-bit Unsigned)
Batch Alarm (Note 4)
W Command 92 DD 1 ~ 14
(Numeric format: 16-bit Unsigned)
clear Alarm History (include
W Command 93 D 0
EEPROM) (Note 1)
W Command 94 D 0 Alarm Clear (Note 1)
W Command 9B D 0 Absolute Clear (Note 1)
Individual Parameter (range: 0x00
W Parameter HH 0 ~ 7f
~ 0x7F) (Note 2)

Note:
1. Command 84, Command 93, Command 94, and Command 9B are write only. (These
commands are able to use Set Bit Object and execute the write command after
triggering Set Bit Object.). Commands other than these four are read only.
2. Parameter read/write: Use device type to define address control from 00~7F.
For example: “address_00” is mapping to “Parameter_00”.
(Please refer to Panasonic MINAS A4 Series User Manual.)
3. Device address type can define MINAS A4 Driver’s command list.
Command 20, Command 27, and Command 28 are Bit type, use “Operating range” to
map communication order status.
For example: “Command 20_3” means “Read state_CCW”.
(Please refer to Panasonic MINAS A4 Series User Manual.)
4. Command 91 and Command 92 are word type, use “Operating range” to map the
record of 14 alarms.
For example: “Command 91_1” means “Read alarm data_First alarm”.

428
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
MINAS A4 Driver CNX4 Port
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 8P Mini-DIN
D-Sub Female D-Sub Female Male
2 RX 8 RX 3 TXD
3 TX 7 TX 5 RXD
5 GND 5 GND 4 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 8P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 5 RXD
5 GND 5 GND 5 GND 4 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 8P Mini-DIN
D-Sub Female Male
9 RX 3 TXD
6 TX 5 RXD
5 GND 4 GND

429
PLC Connection Guide
The following represents the cable end connector.
MINAS A4 Driver CNX3/CNX4 Port
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P Mini-DIN
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 7 D-
2 RX+ 9 Data+ 8 D+
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 8P Mini-DIN
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 7 D-
2 RX+ 9 Data+ 8 D+
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P Mini-DIN
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 7 D-
2 RX+ 8 Data+ 8 D+
5 GND 5 GND

430
PLC Connection Guide

MINAS A4 Driver MINAS A4 Driver

CNX3 Port CNX4 Port
7 D- 3 TX
8 D+ 5 RX
4 GND 4 GND
8P Mini-Din Female
MINAS A4 Driver 7 D-
CNX3 / CNX4 Port
8 D+

RS485 cable / DVOP1970-005

MINAS A4 Driver MINAS A4 Driver
8p Mini-DIN Male 8p Mini-DIN Male
7 D- 7 D-
8 D+ 8 D+
4 GND 4 GND

RS232 cable / DVOP1960

MINAS A4 Driver MINAS A4 Driver
9P D-SUB Female 8p Mini-DIN Male
3 RXD 5 RXD
2 TXD 3 TXD

5 GND ` 4 GND

HMI connect with one Device

Weintek HMI
Panasonic
Com RS232 MINAS A4
Driver X4

Station No. 0
HMI connect with multi devices

431
PLC Connection Guide

Weintek HMI
Com RS232 Panasonic
MINAS A4 Driver X3
Driver X4 Driver X3 Driver X4
RS232
RS485 RS485

Station No. 1 Station No. F

Station No. 0

Driver Version:
Version Date Description
V1.10 Jan/11/2010

432
PLC Connection Guide

Panasonic MINAS A5
Supported Series: Panasonic MINAS A5 series Servo Drive.

HMI Setting:
Parameters Recommended Options Notes
PLC type Panasonic MINAS A5
PLC I/F RS232 RS232/RS485 2W
Baud rate 9600 2400~115200
Data bits 8
Parity None
Stop bits 1
Axis no. 0 (master station only) 0 ~ 127 (slave)
* When connecting with more than two devices, it is recommended to set timeout to more
than 4 seconds. Set a longer timeout when connecting with more devices to maintain good
communication.

433
PLC Connection Guide
Bit/Word Device type Format Range Memo
present deviation counter
W Command 26 D 0~1
(Numeric format: 32-bit Signed)
write parameter to EEPROM
W Command 72 D 0
(Note 1)
present Alarm Data
W Command 90 D 0
(Numeric format: 16-bit Unsigned)
Batch Alarm (Note 4)
W Command 92 DD 1 ~ 14
(Numeric format: 16-bit Unsigned)
clear Alarm History (include
W Command 93 D 0
EEPROM) (Note 1)
W Command 94 D 0 Alarm Clear (Note 1)
W Command 9B D 0 Absolute Clear (Note 1)
Individual Parameter (range: 0x000
W Parameter HHH 0 ~ 639
~ 0x639) (Note 2)

Note:
1. Command 72, Command 93, Command 94, and Command 9B are write only. (These
commands are able to use Set Bit Object and execute the write command after
triggering Set Bit Object.). Commands other than these four are read only.
2. Parameter read/write: Use device type to define address control from 000~639.
For example: “address_000” is mapping to “Parameter_000”.
(Please refer to Panasonic MINAS A5 Series User Manual.)
3. Device address type can define MINAS A5 Driver’s command list.
Command 20, Command 27, and Command 28 are Bit type, use “Operating range” to
map communication order status.
For example: “Command 20_3” means “Read state_CCW”.
(Please refer to Panasonic MINAS A5 Series User Manual.)
4. Command 92 are word type, use “Operating range” to map the record of 14 alarms.

434
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
MINAS A5 Driver X2 Port RS232 Signal
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 8P Connector
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 4 RXD
5 GND 5 GND 1 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 8P Connector
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 1 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 8P Connector
D-Sub Female
9 RX 3 TXD
6 TX 4 RXD
5 GND 1 GND

435
PLC Connection Guide
The following represents the cable end connector.
MINAS A5 Driver X2 Port RS485 Signal
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P
9P D-Sub Male 9P D-Sub Male Connector
1 RX- 6 Data- 5,7 485-
2 RX+ 9 Data+ 6,8 485+
5 GND 5 GND 1 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 8P
9P D-Sub Male 9P D-Sub Male Connector
1 RX- 6 Data- 5,7 485-
2 RX+ 9 Data+ 6,8 485+
5 GND 5 GND 1 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P
9P D-Sub Female 9P D-Sub Female Connector
1 RX- 7 Data- 5,7 485-
2 RX+ 8 Data+ 6,8 485+
5 GND 5 GND 1 GND

Driver Version:
Version Date Description
V1.00 May/23/2012 Driver released.

436
PLC Connection Guide

Parker ACR9000
Supported Series: Parker ACR9000.

Website: http://www.parkermotion.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Parker ACR9000
PLC I/F RS232 RS485 4W / RS232
Baud rate 38400 1200 - 38400
Data bits 8 7,8
Parity None Even, Odd, None
Stop bits 1 1,2
PLC sta. no. 0

Online simulator YES Extend address mode

Device Address:
Bit/Word Device type Format Range Memo
B P_Low16bit DDDDDdd 0 ~ 9999915
B P_High16bit DDDDDdd 0 ~ 9999915
W P_Int32 DDDDD 0 ~ 99999
W P_Float DDDDD 0 ~ 99999

437
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P Parker AC9000 RS232
D-Sub Female D-Sub Female 9P D-Sub Male
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P Parker AC9000 RS232
D-Sub Female D-Sub Female D-Sub Male 9P D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P Parker AC9000 RS232
D-Sub Female 9P D-Sub Male
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Dec/30/2008 Driver released.

438
PLC Connection Guide

Parker Compax3
Supported Series: Parker Compax3 Servo Drive.

Website: http://www.parker.com

HMI Setting:

RS232
Parameters Recommended Options Notes
PLC type Parker Compax3
PLC I/F RS232
Baud rate 115200
Data bits 8 7 or 8
Parity None Even, Odd, None
Stop bits 1 1 or 2
PLC sta. no. 0 0 Must be 0 for RS232

RS485
Parameters Recommended Options Notes
PLC type Parker Compax3
PLC I/F RS485 2W
Baud rate 9600
Data bits 8 7 or 8
Parity None Even, Odd, None
Stop bits 1 1 or 2
Range from 1 to 99 for
PLC sta. no. 1 1-99 RS485, according to the
PLC setting.

439
PLC Connection Guide

PLC Setting:
How to set Compax 3 servo to RS485 mode?
1. Open C3 ServoManager2, select “Communication” => “RS-485 Settings”.

2. Click to Configure “RS-485/POP Settings”.

3. Set parameters as below:

440
PLC Connection Guide
4. Download settings to Compax3 Servo.

5. Set EasyBuilder system parameter and connect with PLC for communication of HMI
and Servo.

Device Address:
Bit/Word Device type Format Range Memo
B R_Low16bit DDDDDDDDh 0 ~ 99999999f
B R_High16bit DDDDDDDDh 0 ~ 99999999f
DW Register_Int DDDDDD 0 ~ 999999 For Register INT32, U32
DW Register_float DDDDDD 0 ~ 999999 For Register INT32, U32
W Register_Short DDDDDD 0 ~ 999999 For Register INT16, U16

Wiring Diagram:
The following represents the cable end connector.
Parker Compax3 PLC X10 : RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND

441
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND

The following represents the cable end connector.

Parker Compax3 PLC X10 : RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 3 RXD
2 RX+ 9 Data+ 7 TXD
5 GND 5 GND 5 GND
1 nable RS485
circuit
9 +5V

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 3 RXD
2 RX+ 9 Data+ 7 TXD
5 GND 5 GND 5 GND
1 nable RS485
circuit
9 +5V

442
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 3 RXD
2 RX+ 8 Data+ 7 TXD
5 GND 5 GND 5 GND
1 nable RS485
circuit
9 +5V

Driver Version:
Version Date Description
V1.70 Mar/30/2009

443
PLC Connection Guide

Parker Compumotor 6K Series

HMI Setting:
Parameters Recommended Options Notes
PLC type Parker Compumotor 6K Series
PLC I/F RS232
Baud rate 9600
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B VARB(L) DDDdd 1 ~ 125 The lower 16 bits data of VARB
B VARB(H) DDDdd 1 ~ 125 The higher 16 bits data of VARB
D RUN_PRG D 0
DW VARI DDD 1 ~ 125
Must select single float data
DW VAR DDD 1 ~ 125
mode.

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P PLC RS232 9P D-Sub
D-Sub Female D-Sub Female Male
2 RX 8 RX 3 TX
3 TX 7 TX 2 RX
5 GND 5 GND 5 GND

444
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P PLC RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 3 TX
3 TX 4 TX 7 TX 2 RX
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P PLC RS232 9P D-Sub
D-Sub Female Male
9 RX 3 TX
6 TX 2 RX
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Apr/7/2011 Driver released.

445
PLC Connection Guide

Parker SLVD Series

Supported Series : Parker SLVD Servo, SLVD1N, SLVD2N, SLVD5N, SLVD7N,
SLVD10N, SLVD15N, SLVD17N.

Website: http://www.parker.com/portal/site/PARKER/

HMI Setting:
Parameters Recommended Options Notes
PLC type Parker SLVD Series
PLC I/F RS485 4W
Baud rate 9600 9600/19200
Data bits 8 7,8
Parity Even Even, Odd, None
Stop bits 1 1,2
PLC sta. no. 0 0-31

Online simulator YES Extend address mode

Device Address:
Bit/Word Device type Format Range Memo
B Par_Binary DDDDdd 0 ~ 999915 Set bit parameter
W Par_One_Word DDDD 0 ~ 9999 Set 2 bytes parameter
DW Par_Two_Word DDDD 0 ~ 9999 Set 4 bytes parameter
W Par_One_Byte DDDD 0 ~ 9999 Set 1 byte prarmeter
W RESET D 0
W RUN D 0

446
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
Parker SLVD Servo Serial Link X1
eMT3000 series
COM1 RS485 4W RS485 4W 15P D-Sub
9P D-Sub Male Male
1 RX- 7 TX-
2 RX+ 12 TX+
3 TX- 2 RX-
4 TX+ 1 RX+
circuit
6 TER
5 GND 3 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 15P D-Sub
9P D-Sub Male Male
1 RX- 7 TX-
2 RX+ 12 TX+
3 TX- 2 RX-
4 TX+ 1 RX+
circuit
6 TER
5 GND 3 GND

447
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W RS485 4W 15P D-Sub
9P D-Sub Female Male
1 RX- 7 TX-
2 RX+ 12 TX+
3 TX- 2 RX-
4 TX+ 1 RX+
circuit
6 TER
5 GND 3 GND

Driver Version:
Version Date Description
V1.00 Jan/27/2010 Driver released.

448
PLC Connection Guide

Rockwell CompactLogix - Free Tag Names

Website: http://www.ab.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Allen-Bradley CompactLogix – Free Tag Names
PLC I/F RS232
Baud rate 19200 9600, 19200, 38400
Data bits 8 8
Parity None Even, Odd, None
Stop bits 1 1
HMI sta. no. 0
PLC sta. no. 1 1-31

PLC Setting:
DF1 Full Duplex protocol 19200, None, 8, 1 (default)
Communication mode
Error Check: BCC, Station Address: 1

Device Address:
PLC Data EasyBuilder Data
Bit/Word Memo
Type Name Format

BOOL Boolean Bit object

BitArray

SINT

16-bit signed,
INT Integer -32768 ~ 32767
ASCII

DINT Double Integer 32-bit signed -231 ~ (231-1)

REAL Single Precision Float 32-bit Float IEEE 754

449
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female D-Sub Female
2 RX 8 RX 3 TD
3 TX 7 TX 2 RD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female D-Sub Male D-Sub Female
2 RX 6 RX 8 RX 3 TD
3 TX 4 TX 7 TX 2 RD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female
9 RX 3 TD
6 TX 2 RD
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 June/2/2011 Driver released.

450
PLC Connection Guide

Rockwell CompactLogix/FlexLogix
Supported Series: Rockwell ControlLogix, CompactLogix, FlexLogix CH0 DF1.

Website: http://www.ab.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Allen-Bradley CompactLogix/FlexLogix
PLC I/F RS232
Baud rate 19200 9600, 19200, 38400
Data bits 8 8
Parity None Even, Odd, None
Stop bits 1 1
HMI sta. no. 0
PLC sta. no. 1 1-31

PLC Setting:
DF1 Full Duplex protocol 19200, None, 8, 1 (default)
Communication mode
Error Check: BCC, Station Address: 1

451
PLC Connection Guide
ControlLogix, CompactLogix CPU CH0 setting:

Create a Tag:
The name format must be 4 chars. For example: B003, T004, C005, N007, and F008.
Two or three chars are not available. For example: B03 or B3.

452
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
B B_BOOL FFFDDDdd 0 ~ 25525515 Bit data file
Integer data file bit level (N7, 10 ~
B N_BOOL FFFDDDdd 0 ~ 25525515
255)
Timer Accumulator Value (T4, T10
DW Tx.ACC FFFDDD 0 ~ 255255
~ 255)
Timer Preset Value
DW Tx.PRE FFFDDD 0 ~ 255255
(T4, T10 ~ 255)
Integer data file
DW Nx_INT FFFDDD 0 ~ 255255
(N7, 10 ~ 255)
W Bx_INT FFFDDD 0 ~ 255255 Bit data file word level
Counter Accumulator Value (C5,
DW Cx.ACC FFFDDD 0 ~ 255255
C10 ~ 255)
Counter Preset Value
DW Cx.PRE FFFDDD 0 ~ 255255
(C5, C10 ~ 255)
Floating point data file
W F8_REAL DDD 0 ~ 255
(F8)
Floating point data file (F008, F010
W Fx_REAL FFFDDD 0 ~ 255255
~ F255)

453
PLC Connection Guide

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female D-Sub Male D-Sub Female
2 RX 6 RX 8 RX 3 TD
3 TX 4 TX 7 TX 2 RD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female
9 RX 3 TD
6 TX 2 RD
5 GND 5 GND

Driver Version:
Version Date Description
V1.50 Dec/30/2008

454
PLC Connection Guide

Rockwell DF1
Supported Series: Rockwell MicroLogix 1000, 1100, 1200, 1400, 1500, SLC 5/03, 5/04,
5/05.

Website: http://www.ab.com
Note: Allen-Bradley DF1 driver uses CRC checksum.

HMI Setting:
Parameters Recommended Options Notes
PLC type Allen-Bradley DF1
PLC I/F RS232
Baud rate 9600 9600, 19200, 38400
Data bits 8 8
Parity None Even, Odd, None
Stop bits 1 1
HMI sta. no. 0
PLC sta. no. 1 1-31

PLC Setting:
DF1 Full Duplex protocol 19200, None, 8, 1 (default)
Communication mode
Error Check: CRC

Device Address:
Bit/Word Device type Format Range Memo
B I1 DDDdd 0 ~ 25515 Input (I)
B O0 DDDdd 0 ~ 25515 Output (O)
B B3 DDDdd 0 ~ 25515 Bit data file (B3)
B B10 ~ 13 DDDdd 0 ~ 25515 Bit data file (B10 ~ 13)
B S_Bit DDDdd 0 ~ 25515 Status (S) bit level
B Bfn FFFDDDdd 0 ~ 25525515 Bit data file (B3, 10 ~ 254)
Integer data file bit level
B NfnBit FFFDDDdd 0 ~ 25525515
(N7, 10 ~ 254)
W T4SV DDD 0 ~ 255 Timer Preset Value (T4)
W T4PV DDD 0 ~ 255 Timer Accumulator Value (T4)

455
PLC Connection Guide
Bit/Word Device type Format Range Memo
W C5SV DDD 0 ~ 255 Counter Preset Value (C5)
W C5PV DDD 0 ~ 255 Counter Accumulator Value (C5)
W TfnSV FFFDDD 0 ~ 255255 Timer Preset Value
W TfnPV FFFDDD 0 ~ 255255 Timer Accumulator Value
W CfnSV FFFDDD 0 ~ 255255 Counter Preset Value
W CfnPV FFFDDD 0 ~ 255255 Counter Accumulator Value
W N7 DDD 0 ~ 255 Integer data file (N7)
W N10 ~ 15 DDD 0 ~ 255 Integer data file (N10 ~ 15)
Integer data file
W Nfn FFFDDD 0 ~ 255255
(N7, 10 ~ 254)
W S DDD 0 ~ 255 Status (S)
W F8 DDD 0 ~ 255 Floating point data file (F8)
W Ffn FFFDDD 0 ~ 255255
W Lfn FFFDDD 0 ~ 255255

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 8P Mini-DIN: MicroLogix 1000, 1100, 1200, 1400, 1500
eMT3000 series
COM1 RS232 9P COM3 RS232 9P MicroLogix RS232 8P
D-Sub Female D-Sub Female Mini-DIN Male
2 RX 8 RX 7 TXD
3 TX 7 TX 4 RXD
5 GND 5 GND 2 GND

456
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P MicroLogix RS232 8P
D-Sub Female D-Sub Female D-Sub Male Mini-DIN Male
2 RX 6 RX 8 RX 7 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 2 GND

MT6050i/MT8050i
COM1 RS232 9P MicroLogix RS232 8P
D-Sub Female Mini-DIN Male
9 RX 7 TXD
6 TX 4 RXD
5 GND 2 GND

The following represents the cable end connector.

9P D-Sub to 9P D-Sub: SLC5/03, 04, 05 CH0
eMT3000 series
COM1 RS232 9P COM3 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female D-Sub Female
2 RX 8 RX 3 TD
3 TX 7 TX 2 RD
5 GND 5 GND 5 GND

457
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female D-Sub Male D-Sub Female
2 RX 6 RX 8 RX 3 TD
3 TX 4 TX 7 TX 2 RD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female
9 RX 3 TD
6 TX 2 RD
5 GND 5 GND

Driver Version:
Version Date Description
V2.20 Jan/05/2010

458
PLC Connection Guide

Rockwell DF1 (BCC)

Supported Series: Rockwell MicroLogix 1000, 1100, 1200, 1500, SLC 5/03, 5/04, 5/05.

Website: http://www.ab.com
Note: Allen-Bradley DF1 (BCC) and Allen-Bradley DF1 are the same; the only difference is
the use of BCC checksum.

HMI Setting:
Parameters Recommended Options Notes
PLC type Allen-Bradley DF1 (BCC)
PLC I/F RS232
Baud rate 19200 9600, 19200, 38400
Data bits 8 8
Parity None Even, Odd, None
Stop bits 1 1
HMI sta. no. 0
PLC sta. no. 1 1-31

PLC Setting:
DF1 Full Duplex protocol 19200, None, 8, 1 (default)
Communication mode
Error Check: CRC

459
PLC Connection Guide
Bit/Word Device type Format Range Memo
W C5SV DDD 0 ~ 255 Counter Preset Value (C5)
W C5PV DDD 0 ~ 255 Counter Accumulator Value (C5)
W TfnSV FFFDDD 0 ~ 255255 Timer Preset Value
W TfnPV FFFDDD 0 ~ 255255 Timer Accumulator Value
W CfnSV FFFDDD 0 ~ 255255 Counter Preset Value
W CfnPV FFFDDD 0 ~ 255255 Counter Accumulator Value
W N7 DDD 0 ~ 255 Integer data file (N7)
W N10~15 DDD 0 ~ 255 Integer data file (N10 ~ 15)
Integer data file
W Nfn FFFDDD 0 ~ 255255 (N7, 10 ~ 254)
W S DDD 0 ~ 255 Status (S)
W F8 DDD 0 ~ 255 Floating point data file (F8)
W Ffn FFFDDD 0 ~ 255255
W Lfn FFFDDD 0 ~ 255255

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 8P Mini-DIN: MicroLogix 1000, 1100, 1200, 1500
eMT3000 series
COM1 RS232 9P COM3 RS232 9P MicroLogix RS232 8P
D-Sub Female D-Sub Female Mini-DIN Male
2 RX 8 RX 7 TXD
3 TX 7 TX 4 RXD
5 GND 5 GND 2 GND

460
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P MicroLogix RS232 8P
D-Sub Female D-Sub Female D-Sub Male Mini-DIN Male
2 RX 6 RX 8 RX 7 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 2 GND

MT6050i/MT8050i
COM1 RS232 9P MicroLogix RS232 8P
D-Sub Female Mini-DIN Male
9 RX 7 TXD
6 TX 4 RXD
5 GND 2 GND

The following represents the cable end connector.

9P D-Sub to 9P D-Sub: SLC5/03, 04, 05 CH0
eMT3000 series
COM1 RS232 9P COM3 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female D-Sub Female
2 RX 8 RX 3 TD
3 TX 7 TX 2 RD
5 GND 5 GND 5 GND

461
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female D-Sub Male D-Sub Female
2 RX 6 RX 8 RX 3 TD
3 TX 4 TX 7 TX 2 RD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female
9 RX 3 TD
6 TX 2 RD
5 GND 5 GND

Driver Version:
Version Date Description
V2.30 Apr/26/2010

462
PLC Connection Guide

Rockwell DH485
Supported Series: Rockwell MicroLogix 1000, 1100, 1200, 1500, SLC 5/03, 5/04, 5/05.

Website: http://www.ab.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Allen-Bradley DH485
PLC I/F RS485 2W RS232
Baud rate 19200 9600, 19200
Data bits 8
Parity Even
Stop bits 1
HMI sta. no. 0 2
PLC sta. no. 1 1-31

Online simulation YES

Extend address mode NO

PLC Setting:
DH485 protocol 19200 (default)
Communication mode
Set the Max. Node Address to the number of PLCs in use.

463
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
B I1 DDDdd 0 ~ 25515 Input (I)
B O0 DDDdd 0 ~ 25515 Output (O)
B B3 DDDdd 0 ~ 25515 Bit data file (B3)
B B10 ~ 13 DDDdd 0 ~ 25515 Bit data file (B10 ~ 13)
B Bfn FFFDDDdd 0 ~ 25525515 Bit data file (B3, 10 ~ 254)
Integer data file bit level (N7,10 ~
B NfnBit FFFDDDdd 0 ~ 25525515
254)
B S_Bit DDDdd 0 ~ 25515 Status file
W T4SV DDD 0 ~ 255 Timer Preset Value (T4)
W T4PV DDD 0 ~ 255 Timer Accumulator Value (T4)
W C5SV DDD 0 ~ 255 Counter Preset Value (C5)
W C5PV DDD 0 ~ 255 Counter Accumulator Value (C5)
W TfnSV FFFDDD 0 ~ 255255 Timer Preset Value
W TfnPV FFFDDD 0 ~ 255255 Timer Accumulator Value
W CfnSV FFFDDD 0 ~ 255255 Counter Preset Value
W CfnPV FFFDDD 0 ~ 255255 Counter Accumulator Value
W F8 DDD 0 ~ 255 Floating point data file (F8)
W N7 DDD 0 ~ 255 Integer data file (N7)
W N10 ~ 15 DDD 0 ~ 255 Integer data file (N10 ~ 15)
Integer data file
W Nfn FFFDDD 0 ~ 255255
(N7,10 ~ 254)
W S DDD 0 ~ 255 Status file

464
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
RS-485: SLC500 Fixed type, SLC5/01, 02, 03 CH1.
HMI can’t connect to 1747-AIC peripheral port.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W AB SLC500 DH485
9P D-Sub Male 9P D-Sub Male RJ8 Male
1 RX- 6 Data- 2 SDB
2 RX+ 9 Data+ 1 SDA
5 GND 5 GND 7 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W AB SLC500 DH485
9P D-Sub Male 9P D-Sub Male RJ8 Male
1 RX- 6 Data- 2 SDB
2 RX+ 9 Data+ 1 SDA
5 GND 5 GND 7 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W AB SLC500 DH485
9P D-Sub Female 9P D-Sub Female RJ8 Male
1 RX- 7 Data- 2 SDB
2 RX+ 8 Data+ 1 SDA
5 GND 5 GND 7 GND

465
PLC Connection Guide
9P D-Sub to 8P Mini-DIN: MicroLogix 1000, 1100, 1200, and 1500 must set DH485
protocol.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P MicroLogix RS232 8P
D-Sub Female D-Sub Female Mini-DIN Male
2 RX 8 RX 7 TXD
3 TX 7 TX 4 RXD
5 GND 5 GND 2 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P MicroLogix RS232 8P
D-Sub Female D-Sub Female D-Sub Male Mini-DIN Male
2 RX 6 RX 8 RX 7 TXD
3 TX 4 TX 7 TX 4 RXD
5 GND 5 GND 5 GND 2 GND

MT6050i/MT8050i
COM1 RS232 9P MicroLogix RS232 8P
D-Sub Female Mini-DIN Male
9 RX 7 TXD
6 TX 4 RXD
5 GND 2 GND

466
PLC Connection Guide
9P D-Sub to 9P D-Sub: SLC5/03, 04, 05 CH0 must set DH485 protocol.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female D-Sub Female
2 RX 8 RX 3 TD
3 TX 7 TX 2 RD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female D-Sub Male D-Sub Female
2 RX 6 RX 8 RX 3 TD
3 TX 4 TX 7 TX 2 RD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P AB CPU CH0 RS232 9P
D-Sub Female D-Sub Female
9 RX 3 TD
6 TX 2 RD
5 GND 5 GND

Driver Version:
Version Date Description
V1.20 Apr/17/2009

467
PLC Connection Guide

Rockwell EtherNet/IP (CompactLogix)

Supported Series: Rockwell ControlLogix, CompactLogix, FelxLogix Ethernet.

Website: http://www.ab.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Allen-Bradley EtherNet/IP (CompactLogix)
PLC I/F Ethernet
Port no. 44818
PLC sta. no. 1

PLC Setting:
RSLogix 5000 setting
Create a Tag:
The name format must be 4 chars. For example: B003, T004, C005, N007, and F008.
Two or three chars are not available. For example: B03 or B3.

468
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
B Bx_BOOL FFFDDDdd 0 ~ 25525515 Bit data file
Integer data file bit level (N7, 10
B Nx_BOOL FFFDDDdd 0 ~ 25525515
~ 99)
W Bx_INT FFFDDD 0 ~ 255255 Bit data file word level
Integer data file
W Nx_INT FFFDDD 0 ~ 255255
(N7, 10 ~ 99)
DW (F) F8_REAL DDD 0 ~ 255 Floating point data file (F8)
DW (F) Fx_REAL FFFDDD 0 ~ 255255 Floating point data file (F8)
Counter Accumulator Value (C5,
DW Cx.ACC FFFDDD 0 ~ 255255
C10 ~ 255)
Counter Preset Value
DW Cx.PRE FFFDDD 0 ~ 255255
(C5, C10 ~ 255)
Timer Accumulator Value (T4,
DW Tx.ACC FFFDDD 0 ~ 255255
T10 ~ 255)
Timer Preset Value
DW Tx.PRE FFFDDD 0 ~ 255255
(T4, T10 ~ 255)
DW Lx.DINT FFFDDD 0 ~ 255255

469
PLC Connection Guide

Wiring Diagram:
Driv Direct connect (crossover cable):
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 3 RX+
2 TX- Orange 6 RX-
3 RX+ White/Green 1 TX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 2 TX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Driver Version:
Version Date Description
V1.30 Dec/30/2008
V1.50 Mar/6/2012 Added register: Lx.DINT

470
PLC Connection Guide

Rockwell EtherNet/IP (CompactLogix) – Free Tag

Names

Supported Series: Rockwell CompactLogix, FelxLogix Ethernet

Website: http://www.ab.com

HMI Setting:
Parameters Recommended Options Notes
Allen-Bradley EtherNet/IP
PLC type
(CompactLogix) – Free Tag Names
PLC I/F Ethernet
Port no. 44818
PLC sta. no. 1

PLC Setting:
1. Set PLC IP address.

471
PLC Connection Guide
2. Create Tags.

3. Export Tag data to CSV file.

Note: The List Separator of the exported CSV file must be “,” otherwise it may not work.

The directory of changing system settings: Control Panel / Date, Time, Language, and
Regional Options / Change the format of numbers, dates, and times / Customize /
List separator. Please select “,” and export CSV file after setting.

472
PLC Connection Guide
4. In EasyBuilder, add Allen-Bradley EtherNet/IP (CompactLogix)- Free Tag Names driver.
Input PLC IP address. On System Parameter Settings dialog click [Import Tag…] button.

5. On object dialog, select PLC, click Tag and select a Controller Tag.

Device Address:
PLC data type EasyBuilder data
Bit/Word Memo
name format
BOOL Boolean Bit object
BitArray
SINT
INT Integer 16-bit signed, ASCII -32768 ~ 32767
DINT Double Integer 32-bit signed -231 ~ (231-1)
REAL Single Precision Float 32-bit Float IEEE 754

473
PLC Connection Guide

Driver Version:
Version Date Description
V1.10 Aug/25/2010

474
PLC Connection Guide

Rockwell EtherNet/IP (ControlLogix) – Free Tag

Names

Supported Series: Rockwell ControlLogix, CompactLogix, FelxLogix Ethernet.

Website: http://www.ab.com

HMI Setting:
Parameters Recommended Options Notes
Allen-Bradley EtherNet/IP
PLC type
(ControlLogix) – Free Tag Names
PLC I/F Ethernet
Port no. 44818
PLC sta. no. The same as CPU Slot No.

PLC Setting:
1. Set PLC IP address.

475
PLC Connection Guide
2. Create Tags.

3. Export Tag data to CSV file.

476
PLC Connection Guide
4. In EasyBuilder , add Allen-Bradley EtherNet/IP (ControlLogix) – Free Tag Names driver.
Input PLC IP address. On System Parameter Settings dialog click [Import Tag…] button.

5. On object dialog, select PLC, click Tag and select a Controller Tag.

477
PLC Connection Guide

478
PLC Connection Guide

Driver Version:
Version Date Description
V1.10 Oct/05/2010

479
PLC Connection Guide

Rockwell EtherNet/IP (DF1)

Supported Series: Rockwell MicroLogix 1100, 1400, SLC5/05 Ethernet port.
MicroLogix1000, 1200, 1500, SLC 5/03, 5/04 with 1761-NET-ENI

Website: http://www.ab.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Allen-Bradley EtherNet/IP (DF1)
PLC I/F Ethernet
Port no. 44818
HMI sta. no. 0
PLC sta. no. 1

PLC Setting:
Communication mode Port Setting: 10/100 Mbps Full Duplex/Half Duplex

Device Address:
Bit/Word Device type Format Range Memo
B I1 DDDdd 0 ~ 25515 Input (I)
B O0 DDDdd 0 ~ 25515 Output (O)
B B3 DDDdd 0 ~ 25515 Bit data file (B3)
B S_Bit DDDDDDdd 0 ~ 25525515 Status file
B Bfn FFFDDDdd 0 ~ 25525515 Bit data file (B3, 10 ~ 254)
Integer data file bit level (N7, 10 ~
B NfnBit FFFDDDdd 0 ~ 25525515
254)
W T4SV DDD 0 ~ 255 Timer Preset Value (T4)
W T4PV DDD 0 ~ 255 Timer Accumulator Value (T4)
W C5SV DDD 0 ~ 255 Counter Preset Value (C5)
W C5PV DDD 0 ~ 255 Counter Accumulator Value (C5)
W TfnSV FFFDDD 0 ~ 255255
W TfnPV FFFDDD 0 ~ 255255
W CfnSV FFFDDD 0 ~ 255255

480
PLC Connection Guide
Bit/Word Device type Format Range Memo
W CfnPV FFFDDD 0 ~ 255255
W S DDD 0 ~ 255
W N7 DDD 0 ~ 255 Integer data file (N7)
Integer data file
W Nfn FFFDDD 0 ~ 255255
(N7, 10 ~ 254)
DW (F) F8 DDD 0 ~ 255 Floating point data file (F8)
Floating point data file
DW (F) Ffn FFFDDD 0 ~ 255255
(F8, 10 ~ 254)
Driver version 2.00 or later
DW Lfn FFFDDD 0 ~ 255255
supported

Wiring Diagram:
Direct connect (crossover cable):

COM CPU PWR

RS232 DF1
Ethernet
Crossover cable

MT8000 MicroLogix 1000, 1200,

1761-NET-ENI 1500, SLC 5/03, 5/04

HMI RJ45 Male Wire Color PLC RJ45 Male

1 TX+ White/Orange 3 RX+
2 TX- Orange 6 RX-
3 RX+ White/Green 1 TX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 2 TX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

481
PLC Connection Guide
Through a hub:

Switch Hub

MT8000

SLC 500 SLC 500 SLC 500

HMI RJ45 Male Wire Color PLC RJ45 Male

1 TX+ White/Orange 1 TX+
2 TX- Orange 2 TX-
3 RX+ White/Green 3 RX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 6 RX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Driver Version:
Version Date Description
V2.00 Dec/21/2009 Add Lfn register.

482
PLC Connection Guide

Rockwell PLC5

Website: http://www.ab.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Allen-Bradley PLC5
PLC I/F RS232
Baud rate 19200 9600, 19200
Data bits 8 8
Parity Even Even, Odd, None
Stop bits 1 1
HMI sta. no. 0
PLC sta. no. 1 1-31

PLC Setting:
Communication mode DF1 Full Duplex protocol 19200, None, 8, 1 (default)

Allen-Bradley PLC-5 Family PLCs use DF1 Full Duplex protocol.

For PLC-5/10, PLC-5/15 and PLC-5/25, MT8000 should be connected to the DF1 port on
the 1785-KE module.
For PLC-5/11, PLC-5/20, PLC-5/30 and PLC-5/40, MT8000 should be connected to the
Channel 0 Port on the PLC.

Device Address:
Bit/Word Device type Format Range Memo
B I1 DDDdd 0 ~ 25515 Input (I)
B O0 DDDdd 0 ~ 25515 Output (O)
B B3 DDDdd 0 ~ 99915 Bit data file (B3)
B B10 ~ 13 DDDdd 0 ~ 99915 Bit data file (B10 ~ 13)
B S_Bit DDDDDDdd 0 ~ 25599915
B Bfn FFFDDDdd 0 ~ 25599915
B NfnBit FFFDDDdd 0 ~ 25599915
W T4SV DDD 0 ~ 999 Timer Preset Value (T4)

483
PLC Connection Guide
Bit/Word Device type Format Range Memo
W T4PV DDD 0 ~ 999 Timer Accumulator Value (T4)
W C5SV DDD 0 ~ 999 Counter Preset Value (C5)
W C5PV DDD 0 ~ 999 Counter Accumulator Value (C5)
W TfnSV FFFDDD 0 ~ 255999
W TfnPV FFFDDD 0 ~ 255999
W CfnSV FFFDDD 0 ~ 255999
W CfnPV FFFDDD 0 ~ 255999
W N7 DDD 0 ~ 999 Integer data file (N7)
W N10 ~ 15 DDD 0 ~ 999 Integer data file (N10 ~ 15)
Integer data file
W Nfn FFFDDD 0 ~ 255999
(V2.5.0 or newer)
W S DDD 0 ~ 255
W F8 DDD 0 ~ 999 Floating point data file (F8)
Floating point data file
W Ffn FFFDDD 0 ~ 255999
(V2.5.0 or newer)

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 25P D-Sub: PLC5 CPU CH0
eMT3000 series
COM1 RS232 9P COM3 RS232 9P AB CPU CH0 RS232
D-Sub Female D-Sub Female 25P D-Sub Male
2 RX 8 RX 3 TD
3 TX 7 TX 2 RD
5 GND 5 GND 7 GND

484
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P AB CPU CH0 RS232
D-Sub Female D-Sub Female D-Sub Male 25P D-Sub Male
2 RX 6 RX 8 RX 3 TD
3 TX 4 TX 7 TX 2 RD
5 GND 5 GND 5 GND 7 GND

MT6050i/MT8050i
COM1 RS232 9P AB CPU CH0 RS232
D-Sub Female 25P D-Sub Male
9 RX 3 TD
6 TX 2 RD
5 GND 7 GND

Note:
The default error checking of AB PLC5 is BCC, whereas our driver is CRC.

485
PLC Connection Guide
Access [Channel Configuration] from RSLogix5, under Channel 0 tab, please select “CRC”
for [Error Detect].

Driver Version:
Version Date Description
V1.20 Apr/17/2009

486
PLC Connection Guide

RS Automation OEMAX Series

Supported Series: OEMax NX7/NX7s Controllers.

Website: http://www.oemax.co.kr

HMI Setting:
Parameters Recommended Options Notes
PLC type RS Automation OEMAX Series
PLC I/F RS232
Baud rate 9600 9600, 19200, 38400
Data bits 8 8
Parity None Even, Odd, None
Stop bits 1 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B R DDDdd 0 ~ 25515
B L DDDdd 0 ~ 25515
B M DDDDdd 0 ~ 199915
B K DDDdd 0 ~ 25515 Keep Contact
B F DDDdd 0 ~ 99115 Special Contact
B TC DDD 0 ~ 255 Timer/Counter
W W DDDD 0 ~ 7999 Data Register
W SV DDD 0 ~ 255 Timer/Counter Set Value
W PV DDD 0 ~ 255 Timer/Counter Preset Value
W SR DDD 0 ~ 255 Special Register
W WR DDD 0 ~ 255
W WL DDD 0 ~ 255
W WM DDDD 0 ~ 1999
W WK DDD 0 ~ 255
W WF DDD 0 ~ 991

487
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P Port1 RS232 9P D-Sub
D-Sub Female D-Sub Female Male
2 RX 8 RX 2 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P Port1 RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 2 TXD
3 TX 4 TX 7 TX 3 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P Port1 RS232 9P D-Sub
D-Sub Female Male
9 RX 2 TXD
6 TX 3 RXD
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Dec/30/2008 Driver released.

488
PLC Connection Guide

SAIA PCD PGU Mode

Supported Series : SAIA PCD series PGU mode.

Website :http://www.saia-burgess.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type SAIA PCD PGU Mode PDS driver
PLC I/F RS232 RS232, RS485
Baud rate 9600 9600, 19200
Data bits 7 7,8
Parity Even Even, Odd, None
Stop bits 1 1
PLC sta. no. 1 0-255

Device Address:
Bit/Word Device type Format Range Memo
B Flag DDDD 0 ~ 8191
B Output DDD 0 ~ 511
B Input DDD 0 ~ 511
W Register DDDD 0 ~ 4095
W Counter DDDD 0 ~ 1599
W Timer DDDD 0 ~ 1599
W Reg_Float DDDD 0 ~ 4095 support single float point
W Reg_Word DDDD 0 ~ 4095

489
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
2 RX 3 TXD
3 TX 2 RXD
5 GND 5 GND
7 RTS 6 DSR
7 RTS circuit
8 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
2 RX 3 TXD
3 TX 2 RXD
5 GND 5 GND
7 RTS 6 DSR
7 RTS circuit
8 CTS

6 DSR (Of PGU Port): PGU connected.

Driver Version:
Version Date Description
V1.02 Dec/30/2008

490
PLC Connection Guide

SAIA PCD S-BUS Mode

Supported Series: SAIA PCD series S-Bus mode.

Website: http://www.saia-burgess.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type SAIA PCD S-BUS Mode PDS driver
PLC I/F RS232 RS232, RS485
Baud rate 9600 9600, 19200, 38400
Data bits 8 7,8
Parity None Even, Odd, None
Stop bits 1 1
PLC sta. no. 0 0-255

PLC Setting:
Communication mode 9600,N,8,1 (default)
RS232 Port 0-Type: RS232
RS485 2W S-BUS Mode: Data(S2), Port 1-Type: RS485

1. Open Saia Project Manager SP2.0.150 and create a new project.

491
PLC Connection Guide
2. Give a project name.

3. Create a new project as below.

4. Go to “Online Setting”.

492
PLC Connection Guide
5. Select “PGU”.

6. Go to ”Device Configurator”.

493
PLC Connection Guide
7. Click ” Change Device Type” to select your PLC model.

8. Select RS232 (PGU) in Type and then right click mouse on Onboard
Communications and select ” Properties”.

494
PLC Connection Guide
9. Select “Yes” in Series S-Bus Port: Enabled.

10. Set parameters in S-Bus Mode and Timing then upload to PLC.

495
PLC Connection Guide
11. Go to Online Settings >> Open to select S-Bus for finishing the PLC settings.

Device Address:
Bit/Word Device type Format Range Memo
B Flag DDDD 0 ~ 8191
B Output DDDD 0 ~ 1023
B Input DDDD 0 ~ 1023
B Reg_Bit DDDDdd 0 ~ 1638331 dd: Bit no. (00~31)
DW Register DDDDD 0 ~ 16383
DW Counter DDDD 0 ~ 1599
DW Timer DDDD 0 ~ 1599
DW Reg_Float DDDDD 0 ~ 16383 support single float point
DW DBn DDDDDDDDD 0 ~ 536016383
496
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
SAIA PCD PGU Port
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
7 RTS
circuit
8 CTS

497
PLC Connection Guide
The following represents the cable end connector.
SAIA PCD1 Port #1 (Port #0) Terminal
eMT3000 series
COM1 RS485 2W COM3 RS485 2W SAIA PCD1 Port #1
9P D-Sub Male 9P D-Sub Male (Port #0) Terminal
1 RX- 6 Data- 11 (29)
2 RX+ 9 Data+ 12 (28)
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W SAIA PCD1 Port #1
9P D-Sub Male 9P D-Sub Male (Port #0) Terminal
1 RX- 6 Data- 11 (29)
2 RX+ 9 Data+ 12 (28)
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W SAIA PCD1 Port #1
9P D-Sub Female 9P D-Sub Female (Port #0) Terminal
1 RX- 7 Data- 11 (29)
2 RX+ 8 Data+ 12 (28)
5 GND 5 GND

Driver Version:
Version Date Description
V1.40 Jun/21/2012 DBn address types are added.

498
PLC Connection Guide

SAIA S-BUS (Ethernet)

Supported Series : SAIA PCD series Ethernet-TCP/IP.

Website : http://www.saia-burgess.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type SAIA S-BUS (Ethernet)
PLC I/F Ethernet
Port no. 5050
PLC sta. no. 0

PLC Setting:

499
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
B Flag DDDD 0 ~ 8191
B Output DDDD 0 ~ 1023
B Input DDDD 0 ~ 1023
B Reg_Bit DDDDdd 0 ~ 1638331 dd: Bit no. (00 ~ 31)
DW Register DDDDD 0 ~ 16383
DW Counter DDDD 0 ~ 1599
DW Timer DDDD 0 ~ 1599
DW Reg_Float DDDDD 0 ~ 16383 support single float point
DW DBn DDDDDDDDD 0 ~ 536016383

500
PLC Connection Guide

Driver Version:
Version Date Description
V1.40 Jun/21/2012 DBn address types are added.

501
PLC Connection Guide

Samsung SPC-10
Supported Series: Samsung SPC-10

Website: http://www.samsungelectronics.com/factory_automation/controller/plc/

HMI Setting:
Parameters Recommended Options Notes
PLC type Samsung SPC-10
PLC I/F RS485 2W
Baud rate 9600
Data bits None
Parity 8
Stop bits 1
PLC sta. no. 192

Device Address:
Bit/Word Device type Format Range Memo
B R DDDDdd 0 ~ 999915
B K DDDDdd 0 ~ 999915
B M DDDDdd 0 ~ 999915
B F DDDDdd 0 ~ 999915
W W DDDD 0 ~ 9999

502
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P Mini-DIN
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 6 TR-
2 RX+ 9 Data+ 7 TR+
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 8P Mini-DIN
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 6 TR-
2 RX+ 9 Data+ 7 TR+
5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P Mini-DIN
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 6 TR-
2 RX+ 8 Data+ 7 TR+
5 GND 5 GND 5 GND

Driver Version:
Version Date Description
V1.00 May/19/2009

503
PLC Connection Guide

SCENE6 Controller

HMI Setting:
Parameters Recommended Options Notes
PLC type SCENE6 Controller
PLC I/F RS232
Baud rate 9600
Data bits 8
Parity None
Stop bits 2
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
W Word DD 0 ~ 99

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 Terminal
D-Sub Female D-Sub Female
2 RX 8 RX TD
3 TX 7 TX RD
5 GND 5 GND GND

504
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 Terminal
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX TD
3 TX 4 TX 7 TX RD
5 GND 5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS232 9P RS232 Terminal
D-Sub Female
9 RX TD
6 TX RD
5 GND GND

Driver Version:
Version Date Description
V1.00 Aug/24/2009

505
PLC Connection Guide

Schleicher XCS 20C

Supported Series: Schleicher XCx-Systems Ethernet port. Schleicher XCS series, 20C
model.

Website: http://www.schleicher-electronic.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Schleicher XCS 20C
PLC I/F RS232
Baud rate 38400
Data bits 8
Parity N
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B IX DDDDDo 0 ~ 655357 Input %IX
B QX DDDDDo 0 ~ 655357 Output %QX
B MX DDDDDo 0 ~ 655357 %MX
W IW DDDDD 0 ~ 65535 %IW
W QW DDDDD 0 ~ 65535 %QW
W MW DDDDD 0 ~ 65535 %MW
DW ID DDDDD 0 ~ 65535 %ID
DW QD DDDDD 0 ~ 65535 %QD
DW MD DDDDD 0 ~ 65535 %WD
 Word address must be even.

506
PLC Connection Guide

Wiring Diagram:

The following represents the cable end connector.

eMT3000 series
COM1 RS232 9P COM3 RS232 9P Schleicher XCS20
D-Sub Female D-Sub Female RS232 9P D-Sub Male
2 RX 8 RX 3 TD
3 TX 7 TX 2 RD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P Schleicher XCS20
D-Sub Female D-Sub Female D-Sub Male RS232 9P D-Sub Male
2 RX 6 RX 8 RX 3 TD
3 TX 4 TX 7 TX 2 RD
5 GND 5 GND 5 GND 5 GND

507
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P Schleicher XCS20
D-Sub Female RS232 9P D-Sub Male
9 RX 3 TD
6 TX 2 RD
5 GND 5 GND

Driver Version:
Version Date Description
V1.10 Feb/26/2010

508
PLC Connection Guide

Schleicher XCX 300

Website: http://www.schleicher-electronic.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Schleicher XCX 300
PLC I/F Ethernet RS232, RS422, Ethernet
Port no. 20547
PLC sta. no. 2

PLC Setting:
A variable must be created for HMI access.

510
PLC Connection Guide
The following represents the cable end connector.
Schleicher XCX300 RS232 Port
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Female
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub
D-Sub Female Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND

511
PLC Connection Guide
The following represents the cable end connector.
Schleicher XCX300 RS485 4W Terminal
eMT3000 series
COM1 RS485 4W RS485 4W Terminal
9P D-Sub Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W Terminal
9P D-Sub Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W Terminal
9P D-Sub Female
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

512
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 Nov/30/2009 Driver released.
V1.10 Jun/28/2010 Support RS232, RS422 interface connection.

513
PLC Connection Guide

Schneider MODBUS RTU

Supported Series : Schneider MODBUS RTU CONTROLLER

Website: http://www.schleicher-electronic.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Schneider MODBUS RTU
PLC I/F RS485 RS232/RS485
Baud rate 9600 9600~115200
Data bits 8 7,8
Parity Even Even, Odd, None
Stop bits 1 1,2
PLC sta. no. 1 0-255

Online simulator YES Broadcast command YES

Extend address mode YES

PLC Setting:
Communication mode Modbus RTU protocol

Device Address:
Bit/Word Device type Format Range Memo
B %M DDDDD 0 ~ 65535 Output bit
B 1x DDDDD 0 ~ 65535 Input bit (read only)
B 3x_Bit DDDDDdd 0 ~ 6553515 Input Register bit (read only)
B 4x_Bit DDDDDdd 0 ~ 6553515 Output Register bit
B 0x_multi_coils DDDDD 0 ~ 65535 Write multiple coils
W 3x DDDDD 0 ~ 65535 Input Register (read only)
W %MW DDDDD 0 ~ 65535 Output Register
DW 5x DDDDD 0 ~ 65535 4x double word swap
W 6x DDDDD 0 ~ 65535 4x single word write

514
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female Female
2 RX 8 RX 2 B-
3 TX 7 TX 1 A+
5 GND 5 GND 5 DTP

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub
D-Sub Female D-Sub Female D-Sub Male Female
2 RX 6 RX 8 RX 3 TX
3 TX 4 TX 7 TX 2 RX
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub
D-Sub Female Female
9 RX 3 TX
6 TX 2 RX
5 GND 5 GND

515
PLC Connection Guide
The following represents the cable end connector.
9P D-Sub to 8P Mini-DIN : RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P Mini-DIN
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 2 B-
2 RX+ 9 Data+ 1 A+
5 GND 5 GND 5 DTP
circuit
7 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 8P Mini-DIN
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 2 B-
2 RX+ 9 Data+ 1 A+
5 GND 5 GND 5 DTP
circuit
7 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P Mini-DIN
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 2 B-
2 RX+ 8 Data+ 1 A+
5 GND 5 GND 5 DTP
circuit
7 GND

516
PLC Connection Guide
The following represents the cable end connector.
9P D-Sub to Terminal : RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 3P Terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- B-
2 RX+ 9 Data+ A+
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 3P Terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- B-
2 RX+ 9 Data+ A+
5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 3P Terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- B-
2 RX+ 8 Data+ A+
5 GND 5 GND GND

Driver Version:
Version Date Description
V1.30 Aug/26/2009

517
PLC Connection Guide

Schneider MODBUS TCP/IP

Supported Series : Schneider Modbus RTU TCP/IP Device.
Website: http://www.schleicher-electronic.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Schneider MODBUS TCP/IP
PLC I/F Ethernet
Port no. 502
PLC sta. no. 1 0~255

Device Address:
Bit/Word Device type Format Range Memo
B %M DDDDD 0 ~ 65535 Input bit
B 1x DDDDD 0 ~ 65535 Output bit
B 3x_Bit DDDDDdd 0 ~ 6553515 Input Register bit (read only)
B 4x_Bit DDDDDdd 0 ~ 6553515 Output Register bit
B 6x_Bit DDDDDdd 0 ~ 6553515 Output Register bit
B 0x_multi_coils DDDDD 0 ~ 65535 Write multiple coils
W 3x DDDDD 0 ~ 65535 Input Register
W %MW DDDDD 0 ~ 65535 Output Register
DW 5x DDDDD 0 ~ 65535 4x double word swap
W 6x DDDDD 0 ~ 65535 4x single word write

518
PLC Connection Guide

Driver Version:
Version Date Description
V1.40 Aug/27/2009

519
PLC Connection Guide

Schneider UniTelway
Supported Series: Modicon TSX Micro&Nano&Neza series PLC.

Website: http://www.modicon.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Schneider UniTelway
PLC I/F RS485 2W RS232/RS485
Baud rate 19200 9600~115200
Data bits 8 7,8 Must set to 8 for this protocol
Parity Odd Even, Odd, None
Stop bits 1 1, 2
HMI sta. no. 5 1-8
PLC sta. no. 0 0-3

Online simulator YES Extend address mode YES

Broadcast command NO

PLC Setting:
Communication mode UniTelWay protocol, set PLC as master

Device Address:
Bit/Word Device type Format Range Memo
B S DDDDD 0 ~ 32767 Internal relay
B M DDDDD 0 ~ 32767 Auxiliary relay
B MW.B DDDDDdd 0 ~ 3276715 Data register bit
W MW DDDDD 0 ~ 32767 Data register

520
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
TSX37-XX/TSX07-XX CPU : 9P D-Sub to 9P D-Sub
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P Mini-DIN
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 2 D-
2 RX+ 9 Data+ 1 D+
5 GND 5 GND 7 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 8P Mini-DIN
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 2 D-
2 RX+ 9 Data+ 1 D+
5 GND 5 GND 7 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P Mini-DIN
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 2 D-
2 RX+ 8 Data+ 1 D+
5 GND 5 GND 7 GND

Driver Version:
Version Date Description
V1.30 Sep/24/2009
521
PLC Connection Guide

SEW Movilink
Supported Series: SEW Eurodrive series, model MOVITRAC-07 inverter, MovitracB.
Website: http://sg.sew-eurodrive.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type SEW Movilink
PLC I/F RS485 2W
Baud rate 9600
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 0 0~255

Device Address:
Bit/Word Device type Format Range Memo
B INDEX_Bit DDDDDDDDdd 0 ~ 2552500031
W INDEX DDDDDDDD 0 ~ 25525000
● The MOVITRAC-07 doesn’t support Sub index（other series may support）, please input
000.
● When input D and d, the correct format：Sub index 15, Index 8359, Format is
01508359.

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W Movitrac-07 RS485 2W
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- D- (Green)
2 RX+ 9 Data+ D+ (Red)
5 GND 5 GND

522
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W Movitrac-07 RS485 2W
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- D- (Green)
2 RX+ 9 Data+ D+ (Red)
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W Movitrac-07 RS485 2W
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- D- (Green)
2 RX+ 8 Data+ D+ (Red)
5 GND 5 GND

Driver Version:
Version Date Description
V1.31 Jun/25/2010

523
PLC Connection Guide

SEW MOVITRAC LTE

Website : http://www.seweurodrive.com/index.php

HMI Setting:
Parameters Recommended Options Notes
PLC type SEW MOVITRAC LTE
PLC I/F RS-485 2W
Baud rate 115200
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 1

Online simulator YES Extend address mode NO

Device Address:
Bit/Word Device type Format Range Memo
W P-1 D 0~1 Max. speed limit
W P-2 D 0~1 Min. speed limit
W P-3 D 0~1 Acceleration ramp time
W P-4 D 0~1 Deceleration ramp time
W P-5 D 0~1 Stop mode select
W P-6 D 0~1 Energy optimizer
W P-7 D 0~1 Motor rated voltage
W P-8 D 0~1 Motor rated current
W P-9 D 0~1 Motor rated frequency
W P-10 D 0~1 Motor rated speed
W P-11 D 0~1 Voltage boost
W P-12 D 0~1 Terminal / Keypad control
W P-13 D 0~1 Trip log
W P-14 D 0~1 Extended menu access code
W P-15 D 0~1 Digital input function set
W P-16 D 0~1 Analog input V / mA
W P-17 D 0~1 Output switching frequency

524
PLC Connection Guide
Bit/Word Device type Format Range Memo
W P-18 D 0~1 User relay output select
W P-19 D 0~1 User relay output limit
W P-20 D 0~1 Preset speed 1
W P-21 D 0~1 Preset speed 2
W P-22 D 0~1 Preset speed 3
W P-23 D 0~1 Preset speed 4
W P-24 D 0~1 Deceleration ramp time 2
W P-25 D 0~1 Analog output function select
W P-26 D 0~1 Skip frequency hysteris band
W P-27 D 0~1 Skip frequency
W P-28 D 0~1 V/F characteristic adjustment voltage
W P-29 D 0~1 V/F characteristic adjustment frequency
W P-30 D 0~1 Terminal mode restart function
W P-31 D 0~1 Keypad mode restart function
W P-32 D 0~1 DC injection enable / duration
W P-33 D 0~1 Spin start
W P-34 D 0~1 Brake chopper enable
W P-35 D 0~1 Analog input scaling factor
Comms address; SBus enable/baudrate
W P-36 D 0~1
select; Trip enable / delay
W P-37 D 0~1 Access code definition
W P-38 D 0~1 Parameter access lock
W P-39 D 0~1 Analog input off-set
W P-40 D 0~1 Display speed scaling factor
W P-00-01 D 0~1 Analog input 1 value
W P-00-02 D 0~1 Analog input 2 value
W P-00-03 D 0~1 Speed reference input
W P-00-04 D 0~1 Digital input status
W P-00-05 D 0~1 Reserved
W P-00-06 D 0~1 Reserved
W P-00-07 D 0~1 Applied motor voltage
W P-00-08 D 0~1 DC bus voltage log
W P-00-09 D 0~1 Heatsink temperature
W P-00-10 D 0~1 Hours run meter
W P-00-11 D 0~1 Run time since last trip (1)
W P-00-12 D 0~1 Run time since last trip (2)
W P-00-13 D 0~1 Run time since last disable

525
PLC Connection Guide
Bit/Word Device type Format Range Memo
W P-00-14 D 0~1 Reserved
W P-00-15 D 0~1 DC bus voltage log
W P-00-16 D 0~1 Thermistor temperature log
W P-00-17 D 0~1 Motor current
W P-00-18 D 0~1 Software ID,IO and motor control
W P-00-19 D 0~1 Drive serial number
W P-00-20 D 0~1 Drive identifier
P-00-01 ~ P-00-20 read only.

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W PLC RS485 2W 8P
9P D-Sub Male 9P D-Sub Male RJ45 Male
1 RX- 6 Data- 4-
2 RX+ 9 Data+ 5+
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W PLC RS485 2W 8P
9P D-Sub Male 9P D-Sub Male RJ45 Male
1 RX- 6 Data- 4-
2 RX+ 9 Data+ 5+
5 GND 5 GND

526
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W PLC RS485 2W 8P
9P D-Sub Female 9P D-Sub Female RJ45 Male
1 RX- 7 Data- 4-
2 RX+ 8 Data+ 5+
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 May/19/2011 Driver released.

527
PLC Connection Guide

SHIMADEN MR13/FP93
Supported Series: MR13, FP93 devices

Website: http://www.shimaden.co.jp

HMI Setting:

Parameters Recommended Options Notes

PLC type SHIMADEN MR13/FP93
PLC I/F RS485
Baud rate 9600 1200-19200
Data bits 7 7 or 8
Parity E None/Even
Stop bits 1 1
PLC sta. no. 1 1~255
0, 1 : STX_ETX_CR
Start Character Mode Select 3：@_:_CR 2 : STX_ETX_CR LF For FP93, select 0,1
3 : @_:_CR
0, 1 : Addition
2 : Addition +2’s
BCC Operation Method Select 3：XOR complement
3 : XOR
4 : None

Note：
Address 018C is a communication control register, only when it is set to 1 can this register
be allowed to write to other registers.

528
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
W Channel 1 HHHH 0 ~ ffff Read/Write 1st Channel Register
W Channel 2 HHHH 0 ~ ffff Read/Write 2nd Channel Register
W Channel 3 HHHH 0 ~ ffff Read/Write 3rd Channel Register

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W MR13/FP93 RS485 2W
9P D-Sub Male 9P D-Sub Male Terminal
1 RX- 6 Data- 25 -
2 RX+ 9 Data+ 24 +
5 GND 5 GND 23 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W MR13/FP93 RS485 2W
9P D-Sub Male 9P D-Sub Male Terminal
1 RX- 6 Data- 25 -
2 RX+ 9 Data+ 24 +
5 GND 5 GND 23 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W MR13/FP93 RS485 2W
9P D-Sub Female 9P D-Sub Female Terminal
1 RX- 7 Data- 25 -
2 RX+ 8 Data+ 24 +
5 GND 5 GND 23 GND

529
PLC Connection Guide
MR13 Communication Parameter Settings

Data
Address Parameter Details of Parameter R /W
(hex)
0100 PV Value Within measuring range R
E_SV Execution SV
0101 Within setting range R
Value
OUT Control Output
0102 Within range 0.0～100.0% R
Value
0103 Reserved
0104 Action Flag （See detailed explanation below.） R
0105 Event Output Flag （See detailed explanation below.） R
0106 Reserved
0107 Reserved
0108 REM Value Within setting range R
0109 Reserved
010A Reserved
010B DI Input State Flag （See detailed explanation below.） R

Data
Address Parameter Details of Parameter R /W
(hex)
Refer to the measuring range code
0111 RANGE R
list.
0112 Reserved
DP Position of decimal point（0:Without
0113 R
Decimal Point decimal point 1:With decimal point）
PV Sc_L Lower
0114 For Linear Imput:-1999～9999 unit R
Limit
For Thermocouple, and RTD Input:
PV Sc_H Higher
0115 Measuring range to be displayed. R
Limit

Data
Address Parameter Details of Parameter R/W
(hex)
0120 E_PRG Program Action Flag R
0121 Reserved

530
PLC Connection Guide
0122 Reserved
The number of execution patterns
0123 E_PRT （When program is reset, R
value=7FFEH）
Execution step number
0124 E_STP （When program is reset, R
value=7FFEH）
Remaining time of execution step
0125 E_TIM （When program is reset, R
value=7FFEH）
Execution PID number
0126 E_PID （When program is reset, R
value=7FFEH）

Data
Address Parameter Details of Parameter R/W
(hex)
0184 AT Auto Tuning 0:No execution 1:Execution W

018C Operation 0:Local 1:COM W

PROG RUN/RST 0：RST, 1：RUN

0190 W
Program Run/Reset （Writing is possible only in CH1）

PROG HLD 0：Release, 1：HLD

0191 W
Program Hold （Writing is possible only in CH1）

0300 SV Local SV Value, within set value limiter R/W

Data
Address Parameter Details of Parameter R/W
(hex)

SV Limt_L Lower
030A Within measuring range,
Limit
On condition that SV Limt_L<SV R/W
SV Limt_h Higher
030B Limt_H
Limit

531
PLC Connection Guide
0314 REM SC_L Within measuring range
R/W
On condition that REM SC_L≠REM
0315 REM SC_H
SC_H
0316 REM Bias Range: -1999～5000 unit R/W
0317 REM Filt Range: 0～100 seconds R/W

Remote channel assignment

031A REM-CH 0 ： OFF ，1 ： CH1 ，2 ： CH2 ，3 ： R/W
CH3

Data
Address Parameter Details of Parameter R/W
(hex)
CH2 & CH3 SV follow setting flag 1:
0320 SV Follow SW R/W
Follow 0:No
Follow type deviation SV set value:
0321 SV Follow R/W
1999～5000 unit

0400 FIX P Control Output Proportional Baud R/W

Range: 0.0～999.9%(0.0:OFF)
0401 FIX I Control Output Integral Time R/W
Range: 0～6000 Seconds (0.0:OFF)
0402 FIX D Control Output Derivative Time R/W
Range 0～3600 Seconds (0.0:OFF)
0403 FIX MR Manual Reset Range: -50.0～50.0% R/W
0404 FIX DF Hysteresis Range: 1～999 unit R/W
0405 FIX OUT Limt_L Control Output Lower Limit Output R/W
Limiter Range: 0.0～99.9%
0406 FIX OUT Limt_H Control Output Higher Limit Output R/W
Limiter Range: 0.1～100.0%
0407 FIX SF Control Output Target Value Function R/W
Range: OFF，0.01～1.00
0408 Prog P1 PROG mode PB1 R/W
Range: 0.0～999.9% (0.0:OFF)
0409 Prog I1 PROG mode IT1 R/W
Range: 0～6000 seconds (0.0:OFF)
040A Prog D1 PROG mode DT1 R/W
Range: 0～3600 seconds (0.0:OFF)

532
PLC Connection Guide
040B Prog MR1 PROG mode MR1 R/W
Range: -50.0～50.0%
PROG mode DF1
040C Prog DF1 R/W
Range: 1～999 unit
Prog O_Lmt_L1 PROG mode lower limit side output
040D R/W
limiter 1 Range: 0.0～99.9%
PROG mode higher limit side output
040E Prog O_Lmt_H1 limiter 1 R/W
Range: 0.1～100.0%
PROG mode target value function 1
040F Prog SF1 R/W
Range: OFF,0.01～1.00
PROG mode PB2
0410 Prog P2 R/W
Range: 0.0～999.9% (0.0:OFF)
PROG mode IT2
0411 Prog I2 R/W
Range: 0～6000 seconds (0.0:OFF)
PROG mode DT2
0412 Prog D2 R/W
Range: 0～3600 seconds (0.0:OFF)
PROG mode MR2
0413 Prog MR2 R/W
Range: -50.0～50.0%
PROG mode DF2
0414 Prog DF2 R/W
Range: 1～999 unit
PROG mode lower limit side output
0415 Prog O_Lmt_L2 R/W
limiter 2 Range: 0.0～99.9%
PROG mode higher limit side output
0416 Prog O_Lmt_H2 limiter 2 R/W
Range: 0.1～100.0%
PROG mode target value function 2
0417 Prog SF2 R/W
Range: OFF,0.01～1.00
PROG mode PB3
0418 Prog P3 R/W
Range: 0.0～999.9% (0.0:OFF)
Prog I3 PROG mode IT3
0419 R/W
Range: 0～6000 seconds (0.0:OFF)
PROG mode DT3
041A Prog D3 R/W
Range: 0～3600 seconds (0.0:OFF)
Prog MR3 PROG mode MR3
041B R/W
Range: -50.0～50.0%
PROG mode DF3
041C Prog DF3 R/W
Range: 1～999 unit
041D Prog O_Lmt_L3 PROG mode lower limit side output R/W
533
PLC Connection Guide
limiter 3 Range: 0.0～99.9%
PROG mode higher limit side output
Prog O_Lmt_H3
041E limiter 3 R/W
Range: 0.1～100.0%
PROG mode target value function 3
041F Prog SF3 R/W
Range: OFF,0.01～1.00

0:Not assigned 1:Higher limit

deviation value
2:Lower limit deviation value
3:Out of range between higher &
lower limits
4:Within range between higher &
EV1_MODE R/W
0500 lower limits
5:Higher limit absolute value
6:Lower limit absolute value
7:Scaleover
8:Program RUN 9:Program END
10:Program STEP
Only when Subaddress=EV1_CH.
1. Higher limit deviation value
alarm: 0～1999 unit
2. Lower limit deviation value alarm: 0
～-1999 unit
3. Out of range between higher &
lower limits value alarm: 0～1999
unit
EV1 Set Point R/W
0501 4. Within range between higher and
lower limits value alarm: 0～1999
unit
5. Higher limit absolute value alarm:
Within measuring range
6. Lower limit absolute value alarm:
Within measuring range
Only when Subaddress=EV1_CH.
Alarm hysteresis 1～999 unit
0502 EV1 Diffrnt R/W
Only when Subaddress=EV1_CH.
Alarm stand by 1～4
0503 EV1 Inhibit R/W
Only when Subaddress=EV1_CH.
534
PLC Connection Guide
Alarm delay time 0～9999 seconds
0504 EV1 Delay R/W
Only when Subaddress=EV1_CH.

Channel number setting

0506 EV1_CH R/W
1:CH1, 2:CH2, 3:CH3

0:Not assigned 1:Higher limit

deviation value
2:Lower limit deviation value
3:Out of range between higher &
lower limits
4:Within range between higher &
0510 EV2_MODE lower limits R/W
5:Higher limit absolute value
6:Lower limit absolute value
7:Scaleover
8:Program RUN 9:Program END
10:Program STEP
Only when Subaddress=EV2_CH.
1. Higher limit deviation value
alarm: 0～1999 unit
2. Lower limit deviation value alarm: 0
～-1999 unit
3. Out of range between higher &
lower limits value alarm: 0～1999
unit
0511 EV2 Set Point 4. Within range between higher and R/W
lower limits value alarm: 0～1999
unit
5. Higher limit absolute value alarm:
Within measuring range
6. Lower limit absolute value alarm:
Within measuring range
Only when Subaddress=EV2_CH.
Alarm hysteresis 1～999 unit
0512 EV2 Diffrnt R/W
Only when Subaddress=EV2_CH.
Alarm stand by 1～4
0513 EV2 Inhibit R/W
Only when Subaddress=EV2_CH.
0514 EV2 Delay Alarm delay time 0～9999 seconds R/W
535
PLC Connection Guide
Only when Subaddress=EV2_CH.

Channel number setting

0516 EV2_CH R/W
1:CH1, 2:CH2, 3:CH3

0:Not assigned 1:Higher limit

deviation value
2:Lower limit deviation value
3:Out of range between higher &
lower limits
4:Within range between higher &
0520 EV3_MODE lower limits R/W
5:Higher limit absolute value
6:Lower limit absolute value
7:Scaleover
8:Program RUN 9:Program END
10:Program STEP
Only when Subaddress=EV3_CH.
1. Higher limit deviation value
alarm: 0～1999 unit
2. Lower limit deviation value alarm: 0
～-1999 unit
3. Out of range between higher &
lower limits value alarm: 0～1999
unit
R/W
0521 EV3 Set Point 4. Within range between higher and
lower limits value alarm: 0～1999
unit
5. Higher limit absolute value alarm:
Within measuring range
6. Lower limit absolute value alarm:
Within measuring range
Only when Subaddress=EV3_CH
Alarm hysteresis 1～999 unit
0522 EV3 Diffrnt R/W
Only when Subaddress=EV3_CH.
Alarm stand by 1～4
0523 EV3 Inhibit R/W
Only when Subaddress=EV3_CH.
Alarm delay time 0～9999 seconds
0524 EV3 Delay R/W
Only when Subaddress=EV3_CH.
536
PLC Connection Guide

0526 EV3_CH Channel number setting R/W

1:CH1, 2:CH2, 3:CH3

DI setting flag
0580 DI 0:NON 1:FLW 2:RUN 3:HLD R/W
4:ADV

MEM 1:EEP Program Memory

05B0 R/W
0:RAM Random Memory

Output characteristic setting flag

0600 Out Actn R/W
0:Rev Act. 1:Dir Act
Control output cycle
0601 Out Cyc (Unit:0.5 seconds) Range: 0.5～ R/W
120.0 seconds
0602 Reserved
Soft start setting flag
0603 SOFTSW
0:OFF 1:ON

0610 AT Point AT pointer Range: 0～5000 unit R/W

0:OFF 1:LOCK1 2:LOCK2
0611 Key Lock R/W
3:LOCK3

● When Out_Cyc is written, writing data is adjusted to 0.5 sec as one unit.
● The write command lock by keylock is the same as the screen lock. (Refer to the
manual of the instrument.)
● If there is a change in EV1_CH,EV2_CH,EV3_CH, the related parameters are
initialized.

0701 PV Bias PV bias Range: -1999～1999 unit R/W

0702 PV Filt PV filter Range: 0～100 seconds R/W

Setting of CH2, CH3 PV input follow

0710 PFLW R/W
0:OFF 1:ON
Selection of CH2, CH3 PV display or
not
0711 CH_P R/W
0-0 Window
0: Without 1: With
537
PLC Connection Guide

Selection between FIX and PROG

0800 FP_MOD 0:FIX 1:PROG R/W
(Writing possible only in CH1)
Setting of PV start 0:OFF 1:ON
0801 PV_ST R/W
(Writing possible only in CH1)

STP The number of steps 1～9

0882 R/W
(Writing possible only in CH1)
The number of execution repetitions 1
0883 RPT ～9999 R/W
(Writing possible only in CH1)
Start SV
0884 ST_SV R/W
(Writing possible only in CH1)

● For CH1, PFLW (window 1~30), CH_P (window1-29）display- - - -.The read value is:
7FFEH, To a write command, error（0BH）is returned.

Step No. 1 SV Value

08A0 Step1 SV R/W
(Writing possible only in CH1)
Step No. 1 Step Time
08A1 Step1 Time R/W
(Writing possible only in CH1)
08A2 Step1 PID No Step No. 1 PID No. R/W
08A3 Reserved
Step No. 2 SV Value
08A4 Step2 SV R/W
(Writing possible only in CH1)
Step No. 2 Step Time
08A5 Step2 Time R/W
(Writing possible only in CH1)
08A6 Step2 PID No Step No. 2 PID No. R/W
08A7 Reserved
Step No. 3 SV Value
08A8 Step3 SV R/W
(Writing possible only in CH1)
Step No. 3 Step Time
08A9 Step3 Time R/W
(Writing possible only in CH1)
08AA Step3 PID No Step No. 3 PID No. R/W
08AB Reserved
Step No. 4 SV Value
08AC Step4 SV R/W
(Writing possible only in CH1)
08AD Step4 Time Step No. 4 Step Time R/W
538
PLC Connection Guide
(Writing possible only in CH1)
08AE Step4 PID No Step No. 4 PID No. R/W
08AF Reserved
Step No. 5 SV Value
08B0 Step5 SV R/W
(Writing possible only in CH1)
Step No. 5 Step Time
08B1 Step5 Time R/W
(Writing possible only in CH1)
08B2 Step5 PID No Step No. 5 PID No. R/W
08B3 Reserved
Step No. 6 SV Value
08B4 Step6 SV R/W
(Writing possible only in CH1)
Step No. 6 Step Time
08B5 Step6 Time R/W
(Writing possible only in CH1)
08B6 Step6 PID No Step No. 6 PID No. R/W
08B7 Reserved
Step No. 7 SV Value
08B8 Step7 SV R/W
(Writing possible only in CH1)
Step No. 7 Step Time
08B9 Step7 Time R/W
(Writing possible only in CH1)
08BA Step7 PID No Step No. 7 PID No. R/W
08BB Reserved
Step No. 8 SV Value
08BC Step8 SV R/W
(Writing possible only in CH1)
Step No. 8 Step Time
08BD Step8 Time R/W
(Writing possible only in CH1)
08BE Step8 PID No Step No. 8 PID No. R/W
08BF Reserved
Step No. 9 SV Value
08C0 Step9 SV R/W
(Writing possible only in CH1)
Step No. 9 Step Time
08C1 Step9 Time R/W
(Writing possible only in CH1)
08C2 Step9 PID No Step No. 9 PID No. R/W

Driver Version:
Version Date Description
V1.20 Apr/08/2011

539
PLC Connection Guide

SHJ-A

HMI Setting:
Parameters Recommended Options Notes
PLC type SHJ-A
PLC I/F RS485 2W
Baud rate 9600
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
W Word DD 0 ~ 89

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND

540
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Oct/18/2011 Driver released.

541
PLC Connection Guide

SICK FLEXI SOFT

HMI Setting:
Parameters Recommended Options Notes
PLC type SICK FLEXI SOFT
PLC I/F RS232
9600,19200,3840
Baud rate 115200
0,57600,115200
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 0

Device Address:
Bit/Word Device type Format Range Memo
B I DDo 0 ~ 967 Input
B Q DDo 0 ~ 487 Output
B Logic result DDo 0 ~ 327 Logic Result
B RS-232 DDo 0 ~ 327 RS-232

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P FLEXI soft CPU0 Port0
D-Sub Female D-Sub Female 4P Mini-DIN Male
2 RX 8 RX 3 TX
3 TX 7 TX 2 RX
5 GND 5 GND 4 GND

542
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P FLEXI soft CPU0 Port0
D-Sub Female D-Sub Female D-Sub Male 4P Mini-DIN Male
2 RX 6 RX 8 RX 3 TX
3 TX 4 TX 7 TX 2 RX
5 GND 5 GND 5 GND 4 GND

MT6050i/MT8050i
COM1 RS232 9P FLEXI soft CPU0 Port0
D-Sub Female 4P Mini-DIN Male
9 RX 3 TX
6 TX 2 RX
5 GND 4 GND

Driver Version:
Version Date Description
V1.00 Apr/6/2011 Driver released.

543
PLC Connection Guide

Siemens LOGO (Ethernet)

Supported Series: Siemens LOGO! 0BA7

Website: http://www.siemens.com/entry/cc/en/

HMI Setting:
Parameters Recommended Options Notes
PLC type Siemens S7/200 (Ethernet)
PLC I/F Ethernet
Port no. 102
PLC sta. no. 1 1~99
Local TSAP 1000 Must be greater than 1000
Remote TSAP 2100 Range:2000~2700
★ For TSAP settings please refer to PLC Setting below.

PLC Setting:
Siemens LOGO! multi connection setting requires LOGO! Soft Comfort software to set
PLC to identify the connected devices. The following introduces LOGO! Soft Comfort
settings.

Step 1. Tools -> Ethernet Connections

544
PLC Connection Guide
Step 2. Right click on ”Ethernet Connections” and click ”Add connections” to add a
connection, up to eight connections are allowed.

Step 3. Setting Server

I. Double click on Connection1, then select ”Server Connection”.
II. Local TSAP is system default and can’t be modified. Tick ”Accept all connection
requests” to connect to any IP.
III. Remote TSAP set to ”10.00”.
IV. Connection 2~8 can all be set as above.

Note: The value of Local TSAP and Remote TSAP must be set oppositely in EasyBuilder
for communication.

545
PLC Connection Guide

Step 4. Complete settings, download connection to Siemens LOGO!

Device Address:
Bit/Word Device type Format Range Memo
B I DD 1~24 Read Only
B Q DD 1~16
B M DD 1~27
B V DDDDo 0~1023 VW_Bit
W AI D 1~8
W AQ D 1~2
W AM DD 1~16
W VW DDDD 0~1023 See Table 1 Address Mapping

546
PLC Connection Guide
Table 1 Address Mapping
I VW Q VW M VW AI VW AQ VW AM VW
I1 V923.0 Q1 V942.0 M1 V948.0 AI1 VW926 AQ1 VW944 AM1 VW952
I2 V923.1 Q2 V942.1 M2 V948.1 AI2 VW928 AQ2 VW946 AM2 VW954
I3 V923.2 Q3 V942.2 M3 V948.2 AI3 VW930 AM3 VW956
I4 V923.3 Q4 V942.3 M4 V948.3 AI4 VW932 AM4 VW958
I5 V923.4 Q5 V942.4 M5 V948.4 AI5 VW934 AM5 VW960
I6 V923.5 Q6 V942.5 M6 V948.5 AI6 VW936 AM6 VW962
I7 V923.6 Q7 V942.6 M7 V948.6 AI7 VW938 AM7 VW964
I8 V923.7 Q8 V942.7 M8 V948.7 AI8 VW940 AM8 VW966

I9 V924.0 Q9 V943.0 M9 V949.0 AM9 VW968

I10 V924.1 Q10 V943.1 M10 V949.1 AM10 VW970
I11 V924.2 Q11 V943.2 M11 V949.2 AM11 VW972
I12 V924.3 Q12 V943.3 M12 V949.3 AM12 VW974
I13 V924.4 Q13 V943.4 M13 V949.4 AM13 VW976
I14 V924.5 Q14 V943.5 M14 V949.5 AM14 VW978
I15 V924.6 Q15 V943.6 M15 V949.6 AM15 VW980
I16 V924.7 Q16 V943.7 M16 V949.7 AM16 VW982

I17 V925.0 M17 V950.0

I18 V925.1 M18 V950.1
I19 V925.2 M19 V950.2
I20 V925.3 M20 V950.3
I21 V925.4 M21 V950.4
I22 V925.5 M22 V950.5
I23 V925.6 M23 V950.6
I24 V925.7 M24 V950.7

M25 V951.0
M26 V951.1
M27 V951.2

547
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 DEC/7/2011 Driver released.

548
PLC Connection Guide

Siemens S7-1200 (Ethernet)

Supported Series: Siemens S7-1200 series Ethernet.
Website: http://www.siemens.com/entry/cc/en/

HMI Setting:
Parameters Recommended Options Notes
SIEMENS S7-1200 Siemens S7-400
PLC type
(Ethernet) (Ethernet)
PLC I/F Ethernet Ethernet
Port no. 102 102
PLC sta. no. 2 2
Rack - 0
CPU slot - 1

On-line simulator Yes Multi-PLC connect Yes

PLC Setting:
1. In S7-1200 program software create PLC program and tag and then download to
PLC.
2. Select Go offline, EasyBuilder will connect to PLC and get tag data. In PLC type
select “SIEMENS S7-1200 (Ethernet)”.

549
PLC Connection Guide
3. Click “Settings…”, input PLC IP address.

4. Check the PLC that is not connected to any PC. Click “Get tag info…”.

550
PLC Connection Guide
5. If the software used is a version later than TIA Portal V11，SP2, a dialog of
FunctionBlock directory will be shown, users have to define the mapping from FB to
DB in this directory then click “Check OK”. The tag information will be gained and
a successful message is shown.

551
PLC Connection Guide
6. Create an object and click read address “Setting…”

7. In PLC name select S7-1200 then click Tag.

8. Select PLC tag.

552
PLC Connection Guide

Support Device Type:

S7-1200 data type EasyBuilder data format Memo
Bool bit
16-bit BCD, Hex, Binary,
Byte 8-bit
Unsigned
16-bit BCD, Hex, Binary,
SInt 8-bit
Signed
16-bit BCD, Hex, Binary,
USInt 8-bit
Unsigned
16-bit BCD, Hex, Binary,
Word 16-bit
Unsigned
16-bit BCD, Hex, Binary, 16-bit
Int Signed
16-bit BCD, Hex, Binary, 16-bit
UInt Unsigned
32-bit BCD, Hex, Binary,
DWord 32-bit
Unsigned
32-bit BCD, Hex, Binary,
DInt 32-bit
Signed
Real 32-bit Float 32-bit
32-bit BCD, Hex, Binary,
UDInt 32-bit
Unsigned
Word array for ASCII input
Array Length=word
and ASCII display

553
PLC Connection Guide
Through a hub:
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 1 TX+
2 TX- Orange 2 TX-
3 RX+ White/Green 3 RX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 6 RX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Driver Version:
Version Date Description
V1.70 Oct/7/2011 Add data type: Byte,SInt,UInt,UDInt
V1.90 Apr/26/2012 Add data type: USInt

554
PLC Connection Guide

Siemens S7-200
Supported Series: Siemens S7-200 series PLC
(CPU212/214/215/216/221/222/224/226/226XM)
Website: http://www.siemens.com/entry/cc/en/

HMI Setting:
Parameters Recommended Options Notes
PLC type SIEMENS S7-200
PLC I/F RS485 2w RS485 2w
The HMI which has a sticker
Baud rate 9600 9600, 19200, 187.5K “MPI187.5” on the rear
cover supports 187.5K
Data bits 8 7,8
Parity Even Even, Odd, None
Stop bits 1 1, 2
PLC sta. no. 2 1 ~ 126
Turn around
5
delay (ms)
Reserved 1 30 ACK delay time

Online simulator YES Extend address mode NO

Broadcast command NO

PLC Setting:
Communication mode Set station number to 2

555
PLC Connection Guide
Bit/Word Device type Format Range Memo
W VW DDDDD 0 ~ 10239 V Memory
W VW_Odd DDDDD 0 ~ 10239 V Memory
DW VD DDDDD 0 ~ 10239 V Memory Double Word
DW VD_Odd DDDDD 0 ~ 10239 V Memory Double Word
W VW_String DDDDD 0 ~ 10239 String
W VW_String_Odd DDDDD 0 ~ 10239 String
DW VD_String DDDDD 0 ~ 10239 String
DW VD_String_Odd DDDDD 0 ~ 10239 String
Byte MB DDDDD 0 ~ 10239 Byte Memory
W MW DDDDD 0 ~ 10239 Word Memory
DW MD DDDDD 0 ~ 10239 Word Memory
W MW_Odd DDDDD 0 ~ 10239 Word Memory
W T DDD 0 ~ 127 Timer
W C DDD 0 ~ 127 Counter
 Double word and floating point value must use VD device type.

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 8 D-
2 RX+ 9 Data+ 3 D+
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 8 D-
2 RX+ 9 Data+ 3 D+
5 GND 5 GND 5 GND

556
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 8 D-
2 RX+ 8 Data+ 3 D+
5 GND 5 GND 5 GND

Driver Version:
Version Date Description
V2.30 Aug/17/2009
V2.40 Nov/1/2011 Add device type : MD

557
PLC Connection Guide

Siemens S7-200 (Ethernet)

Supported Series: Siemens S7/200 Ethernet Series PLC
(CPU212/214/215/216/221/222/224/226/226XM) with CP243-1 Ethernet module

Website: http://www.siemens.com/entry/cc/en/

HMI Setting:
Parameters Recommended Options Notes
PLC type SIEMENS S7-200 (Ethernet)
PLC I/F Ethernet
Port no. 102
PLC sta. no. 1 0-31

PLC Setting:
S7/200 Ethernet Multi-Connection Settings
Step 1: Launching the Ethernet Wizard
1. In the Micro/WIN main menu, click Tools / Ethernet Wizard.

558
PLC Connection Guide
2. Then, click Next.

3. Click Yes to proceed.

Step 2: Setting CP243-1 Module Position

1. Click Read Modules.

559
PLC Connection Guide
2. To view the results of Read Modules, select the Ethernet module. Click Next.

Step 3: Assigning Module Address

1. Click Next.

560
PLC Connection Guide
2. Enter the number of desired available connections for this device. If 0 is entered,
the only connection available will be the PG mode. The image below shows there
are 4 connections for this module.

3. Connection0 -> Select This is a Server Connection....

Notice the Local TSAP automatically incremented to 10.00.

561
PLC Connection Guide
4. Connection1，Select This is a Server Connection....
Notice the Local TSAP automatically incremented to 11.00.

5. Upon completion of the settings above, set parameters in EasyBuilder. Set the
value of Local TSAP here to the value of Remote TSAP in Micro/WIN and vice
versa to realize multi-connection.

562
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
B I DDDDo 0 ~ 40957 Input (I)
B Q DDDDo 0 ~ 40957 Output (O)
B M DDDDo 0 ~ 40957 Bit Memory
B VW_Bit DDDDDo 0 ~ 102397 V Memory Bit Address
W VW DDDDD 0 ~ 10239 V Memory
DW VD DDDDD 0 ~ 10239 V Memory Double Word
W VW_String DDDDD 0 ~ 10239 String
DW VD_String DDDDD 0 ~ 10239 String
DW MD DDDDD 0 ~ 10239 Word Memory
 Double word and floating point value must use VD device type.

563
PLC Connection Guide
Through a hub:
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 1 TX+
2 TX- Orange 2 TX-
3 RX+ White/Green 3 RX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 6 RX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Driver Version:
Version Date Description
V1.20 Dec/30/2008
V1.40 Nov/15/2011 Add device type : MD

564
PLC Connection Guide

Siemens S7-200 (VD any address)

Supported Series: Siemens S7-200 series PLC
(CPU212/214/215/216/221/222/224/226/226XM)
Website: http://www.siemens.com/entry/cc/en/

HMI Setting:
Parameters Recommended Options Notes
PLC type Siemens S7-200 (VD any address)
PLC I/F RS485 2w RS485 2w
The HMI which has a sticker
Baud rate 9600 9600, 19200, 187.5K “MPI187.5” on the rear
cover supports 187.5K
Data bits 8 7,8
Parity Even Even, Odd, None
Stop bits 1 1, 2
PLC sta. no. 2 1 ~ 126
Turn around
5
delay (ms)
Reserved 1 30 ACK delay time

Online simulator YES Extend address mode NO

Broadcast command NO

PLC Setting:
Communication mode Set station number to 2

565
PLC Connection Guide

Bit/Word Device type Format Range Memo

DW VD DDDDD 0 ~ 10239 V Memory Double Word
W VW_String DDDDD 0 ~ 10239 String
DW VD_String DDDDD 0 ~ 10239 String
W MW DDDDD 0 ~ 10239 Word Memory
W T DDD 0 ~ 127 Timer
W C DDD 0 ~ 127 Counter
DW MD DDDDD 0 ~ 10239 Word Memory
 Double word and floating point value must use VD device type.
 VD register can set to any value, not necessarily a multiple of 4.

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 8 D-
2 RX+ 9 Data+ 3 D+
5 GND 5 GND 5 GND

566
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 8 D-
2 RX+ 8 Data+ 3 D+
5 GND 5 GND 5 GND

Driver Version:
Version Date Description
V1.20 Nov/16/2011 Add device type : MD

567
PLC Connection Guide

Siemens S7-200 PPI

Supported Series: Siemens S7-200 series PLC
(CPU212/214/215/216/221/222/224/226/226XM)
Website: http://www.siemens.com/entry/cc/en/

HMI Setting:
Parameters Recommended Options Notes
PLC type SIEMENS S7-200 PPI
PLC I/F RS485 2w RS485 2w
9600, 19200, Only MT6000/8000V2 support
Baud rate 9600
187.5K baud rate 187.5 K
Data bits 8 7,8
Parity Even Even, Odd, None
Stop bits 1 1, 2
Turn around
5
delay (ms)
ACK delay
30
time (ms)
PLC sta. no. 2 1 ~ 126

Online simulator YES Extend address mode YES

Broadcast command NO

PLC Setting:
PLC setting PLC sta. no. can not be the same as HMI sta. no.

Device Address:
Bit/Word Device type Format Range Memo
B I DDDDo 0 ~ 40957 Input (I)
B Q DDDDo 0 ~ 40957 Output (O)
B M DDDDo 0 ~ 40957 Bit Memory
B VW_Bit DDDDDo 0 ~ 102397 V Memory Bit Address
Byte VB DDDDD 0 ~ 10239
W VW DDDDD 0 ~ 10239 V Memory
568
PLC Connection Guide
Bit/Word Device type Format Range Memo
W VW_Odd DDDDD 0 ~ 10239 V Memory
DW VD DDDDD 0 ~ 10239 V Memory Double Word
DW VD_Odd DDDDD 0 ~ 10239 V Memory Double Word
W VW_String DDDDD 0 ~ 10239 String
W VW_String_Odd DDDDD 0 ~ 10239 String
DW VD_String DDDDD 0 ~ 10239 String
DW VD_String_Odd DDDDD 0 ~ 10239 String
Byte MB DDDDD 0 ~ 10239 Byte Memory
W MW DDDDD 0 ~ 10239 Word Memory
W MW_Odd DDDDD 0 ~ 10239 Word Memory
W T DDD 0 ~ 127 Timer
W C DDD 0 ~ 127 Counter
DW MD DDDDD 0 ~ 10239 Word Memory
 Double Word and floating point value must use VD device type.

Multi-HMIs-Multi-PLCs Communication Setting:

For S7-200 PLC, Multi-HMIs-Multi-PLCs communication can be achieved using S7/200

PPI driver, please refer to the settings below.

569
PLC Connection Guide
IN EasyBuilder COM Port Settings, two important parameters must be set:

1. [High station address (HSA)]:

Setting Max. Station Number of HMI in PPI network.
For the effectiveness of system operation, it is highly recommended that the HMI station
number starts from zero and go on sequentially. If there are 4 HMI in PPI network, set
station no. from 0~3, and [High station address (HSA)] to 3.
Set HMI station number in [System Parameters] / [Model] / [HMI station no.]:

2. [Gap update factor(GUF)]:

The condition to pass a Token. In PPI network only HMI can hold a Token, PLC can only
be controlled.
When the HMI that holds Token communicates with PLC for a number of times that equals
to the value set here, HMI will pass the Token (control of PLC) to the next HMI. For
example, if GUF is set to “1”, HMI will pass the control of PLC to the next HMI when read
or write the value in an address.
If GUF is set to a bigger value, the HMI that holds Token will control the PLC for a longer
time and therefore the Token won’t be passed to another HMI and cause failure in
communicating with PLC.
A complete communication means HMI reads / writes PLC value for one time.

570
PLC Connection Guide

Note:
 HMI sta. no. can not be the same as PLC sta. no.
 Highly recommended that HMI sta. no. starts from 0 and go on sequentially for the
effectiveness of operation.
 Available for EasyBuilder V4.50 and later.

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 8 D-
2 RX+ 9 Data+ 3 D+
5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 8 D-
2 RX+ 8 Data+ 3 D+
5 GND 5 GND 5 GND

571
PLC Connection Guide

Driver Version
Version Date Description
V1.00 Aug/15/2011 Driver released.
V1.10 Nov/17/2011 Add device type : MD

572
PLC Connection Guide

Siemens S7-300
Supported Series: Siemens S7-300 series PLC

Website: http://www.siemens.com/entry/cc/en/

HMI Setting:
Parameters Recommended Options Notes
PLC type SIEMENS S7-300
PLC I/F RS232
Must be same as the PLC setting.
The HMI which has a sticker
Baud rate 19200 9600~187.5K
MPI187.5 on the rear cover
supports 187.5K.
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. 2 Must be same as the PLC setting.

Device Address:
Bit/Word Device type Format Range Memo
B I DDDDo 0 ~ 40957 Input (I)
B Q DDDDo 0 ~ 40957 Output (O)
B M DDDDo 0 ~ 40957 Bit Memory
B DBnBit FFFFDDDDo 0 ~ 409681927 Data Register Bit
DB0Bit ~
B DDDDo 0 ~ 81927
DB99Bit
W IW DDDD 0 ~ 4095 Input (I)
W QW DDDD 0 ~ 4095 Output (O)
W MW DDDD 0 ~ 4095 Bit Memory
DW MD DDDD 0 ~ 4094
Byte MB DDDD 0 ~ 4095 Bit Memory Byte
Byte DBBn FFFFDDDD 0 ~ 40968192 Data Register Byte
Data Register
W DBn FFFFDDDD 0 ~ 40968192
(must be even)

573
PLC Connection Guide
Bit/Word Device type Format Range Memo
Data Register Double Word
DW DBDn FFFFDDDD 0 ~ 40968192
(must be multiple of 4)
Data Register Double Word
W DBn_String FFFFDDDD 0 ~ 40968192
(must be multiple of 4)
Data Register Double Word
DW DBDn_String FFFFDDDD 0 ~ 40968192
(must be multiple of 4)
Data Register
W DB0-DB99 DDDD 0 ~ 8192
(must be even)
* Double word and floating point value must use DBDn device type.

How to Import Tag:

SIEMENS STEP 7 program allows building files of user-defined tag (*.dif file and *.AWL
file), and import these files in EasyBuilder8000/EasyBuilderPro -> System Parameter
Settings. The following describes how to build and import these two types of files.
1. Building *.dif File
a、 In “Symbols” create user-defined tag.

574
PLC Connection Guide
b、 Click Export to export the edited file and click Save.

2. Building *.AWF File

a、 In Blocks create items as shown below:

b、 Open LAD/STL, FBD – Programming S7 Blocks, click File -> Generate

Source.

575
PLC Connection Guide
c、 Select Sources as storage path, specify the file name then click OK.

d、 Select the objects to be exported then click OK.

576
PLC Connection Guide
e、 Under Sources there will be names of the saved files, select Export Source
to build *.AWL file.

The generated .dif and .AWL files can be imported in EasyBuilder8000/EasyBuilderPro

System Parameter Settings, by clicking Import Tag.

Tag information successfully imported.

577
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
Siemens S7-300 PC Adapter : 9P D-Sub to 9P D-Sub:
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
7 RTS
circuit
8 CTS

578
PLC Connection Guide
The following represents the cable end connector.
Systeme Helmholz SSW7-TS : 9P D-Sub to 9P D-Sub
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS
4 DTR
circuit
6 DSR

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS
4 DTR
circuit
6 DSR

579
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
7 RTS
circuit
8 CTS
4 DTR
circuit
6 DSR

Driver Version:
Version Date Description
V3.10 May/24/2011 Added registers: MB & DBBn.

580
PLC Connection Guide

Siemens S7-300 MPI

Supported Series: Siemens S7-300 series PLC
Website: http://www.siemens.com/entry/cc/en/

HMI Setting:
Parameters Recommended Options Notes
PLC type SIEMENS S7-300 MPI
PLC I/F RS-485 2W
Only HMI with a sticker “MPI 187.5K”
Baud rate 187.5K on the rear cover supports MPI
communication.
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 2 2 ~ 31

Online simulator NO Extend address mode Yes

Broadcast command NO

W DBn FFFFDDDD 0 ~ 40969999 Data Register (must be even)

581
PLC Connection Guide
Bit/Word Device type Format Range Memo

Data Register Double Word

DW DBDn FFFFDDDD 0 ~ 40969999
(multiple of 4)

W DBn_String FFFFDDDD 0 ~ 40969999

DW DBDn_String FFFFDDDD 0 ~ 40969999
W DB0 ~ DB99 DDDDD 0 ~ 65532 Data Register (must be even)
 Double word and floating point value must use DBDn device type.

Multi-HMIs-Multi-PLCs Communication Setting:

For SIEMENS S7-300 MPI driver in Multi-HMIs-Multi-PLCs communication, [Max. station

no. (MPI network)] parameter must be correctly set. This setting is relevant to the station
no. of the devices, as shown, two HMI (station no. 0, 1) and two PLC (station no. 2, 3) are
in MPI network, Max. Station No. should be set to 3.

582
PLC Connection Guide
For the effectiveness of communication, users may set PLC device in STEP 7 as shown
below. In Properties MPI / Network Settings, set Highest MPI address to the number
closest to the actual device station number.

Note:
■ HMI sta. no. can not be the same as PLC sta. no.
■ Highly recommended that the device station numbers start from 0 sequentially and
correctly set [Max. station no. (MPI network)].
■ Available for EasyBuilder V4.50 and later.

How to Import Tag:

583
PLC Connection Guide
1. Building *.dif File
a、 In “Symbols” create user-defined tag.

b、 Click Export to export the edited file and click Save.

584
PLC Connection Guide
2. Building *.AWF File
a、 In Blocks create items as shown below:

b、 Open LAD/STL, FBD – Programming S7 Blocks, click File -> Generate

Source.

c、 Select Sources as storage path, specify the file name then click OK.

585
PLC Connection Guide
d、 Select the objects to be exported then click OK.

e、 Under Sources there will be names of the saved files, select Export
Source to build *.AWL file.

586
PLC Connection Guide
The generated *.dif and *.AWL files can be imported in EasyBuilder8000/EasyBuilderPro
System Parameter Settings, by clicking Import Tag.

Tag information successfully imported.

587
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
S7-200 PPI , S7-300 MPI :RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 8 D-
2 RX+ 9 Data+ 3 D+
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 8 D-
2 RX+ 9 Data+ 3 D+
5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 8 D-
2 RX+ 8 Data+ 3 D+
5 GND 5 GND 5 GND

Driver Version:
Version Date Description
V1.90 May/26/2011 Added registers: MB & DBBn
i Series HMI support Multi HMIs-Multi PLCs
V2.00 Aug/19d/2011
communication.

588
PLC Connection Guide

Siemens S7-300/ET200S (Ethernet)

Supported Series: Siemens S7-300 Ethernet Series PLC, Ethernet module CP-343-1,
CPU315-2 PN/DP, CPU317-2 PN/DP, CPU319-3 PN/DP, and ET200S.
Website: http://www.siemens.com/entry/cc/en/

HMI Setting:
Parameters Recommended Options Notes
PLC type SIEMENS S7-300/ET200S (Ethernet)
PLC I/F Ethernet
Port no. 102
PLC sta. no. 1 0-31

Device Address:
Bit/Word Device type Format Range Memo
B I DDDDo 0 ~ 40957 Input (I)
B Q DDDDo 0 ~ 40957 Output (O)
B M DDDDo 0 ~ 40957 Bit Memory
B DBnBit FFFFDDDDo 0 ~ 409699997
B DB0Bit-DB99Bit DDDDDo 0 ~ 655327 Data Register Bit
W IW DDDD 0 ~ 4095 Input (I)
W QW DDDD 0 ~ 4095 Output (O)
W MW DDDD 0 ~ 4095 Bit Memory
DW MD DDDD 0 ~ 4094 Bit Memory Double Word
Bit Memory Double Word
DW MD_Anyaddr DDDD 0 ~ 4094
(must be even)
Data Register
W DBn FFFFDDDD 0 ~ 40969999
(must be even)
Data Register Double Word
DW DBDn FFFFDDDD 0 ~ 40969999
(must be multiple of 4)
Data Register Double Word
DW DBDn_Anyaddr FFFFDDDD 0 ~ 40969999
(must be even)
W DBn_String FFFFDDDD 0 ~ 40969999
DW DBDn_String FFFFDDDD 0 ~ 40969999
W DB0 ~ DB99 DDDDD 0 ~ 65532 Data Register

589
PLC Connection Guide
Bit/Word Device type Format Range Memo
(must be even)
Byte MB DDDD 0 ~ 4095 Bit Memory Byte
Byte DBBn FFFFDDDD 0 ~ 40969999 Data Register Byte
 Double word and floating point value must use DBDn device type.

How to Import Tag:

1. Building *.dif File

a、 In “Symbols” create user-defined tag.

590
PLC Connection Guide
b、 Click Export to export the edited file and click Save.

2. Building *.AWF File

a、 In Blocks create items as shown below:

b、 Open LAD/STL, FBD – Programming S7 Blocks, click File -> Generate

Source.

591
PLC Connection Guide
c、 Select Sources as storage path, specify the file name then click OK.

d、 Select the objects to be exported then click OK.

592
PLC Connection Guide
e、 Under Sources there will be names of the saved files, select Export Source
to build *.AWL file.

The generated .dif and .AWL files can be imported in EasyBuilder8000/EasyBuilderPro

System Parameter Settings, by clicking Import Tag.

Tag information successfully imported.

593
PLC Connection Guide

Driver Version:
Version Date Description
V2.10 May/21/2011 Added registers: MB & DBBn.
V2.20 Apr/25/2012 Added registers: MD_Anyaddr & DBDn_Anyaddr.

594
PLC Connection Guide

Siemens S7-400 (Ethernet)

Supported Series: Siemens S7-400/1200 Ethernet PLC.
Website: http://www.siemens.com/entry/cc/en/

HMI Setting:
Parameters Recommended Options Notes
PLC type Siemens S7-400 (Ethernet)
PLC I/F Ethernet
Port no. 102
Link type PG PC, OP
Rack 0 0-7
To Connect with S7-1200,slot 1
CPU slot 3 1-31
must be selected.
PLC sta. no. 0 0-31

Device Address:
Bit/Word Device type Format Range Memo
B I DDDDo 0 ~ 40957 Input (I)
B Q DDDDo 0 ~ 40957 Output (O)
B M DDDDo 0 ~ 40957 Bit Memory
B DBnBit FFFFDDDDo 0 ~ 409699997
B DB0Bit-DB99Bit DDDDDo 0 ~ 655327 Data Register Bit
W IW DDDD 0 ~ 4095 Input (I)
W QW DDDD 0 ~ 4095 Output (O)
W MW DDDD 0 ~ 4095 Bit Memory
DW MD DDDD 0 ~ 4094
Data Register
W DBn FFFFDDDD 0 ~ 40969999
(must be even)
Data Register Double Word
DW DBDn FFFFDDDD 0 ~ 40969999
(must be multiple of 4)
W DBn_String FFFFDDDD 0 ~ 40969999
DW DBDn_String FFFFDDDD 0 ~ 40969999
Data Register
W DB0 ~ DB99 DDDDD 0 ~ 65532
(must be even)
Byte MB DDDD 0 ~ 4095 Bit Memory Byte
Byte DBBn FFFFDDDD 0 ~ 40969999 Data Register Byte
* Double word and floating point value must use DBDn device type.

595
PLC Connection Guide

596
PLC Connection Guide

EasyBuilder Device Setting Steps

1. Open EasyBuilder, File/NEW, select HMI model and press [OK].

2. ”System Parameter Settings” window is shown, click [New].

3. Select “SIEMENS S7-400(ETHERNET)”.

4. Press [Settings].

597
PLC Connection Guide
5. Set S7-400 IP, Port no., Link type, Rack and CPU slot. (must match PLC settings)

6. The setting will be finished as below.

598
PLC Connection Guide

How to Import Tag:

b、 Click Export to export the edited file and click Save.

599
PLC Connection Guide
2. Building *.AWF File
a、 In Blocks create items as shown below:

b、 Open LAD/STL, FBD – Programming S7 Blocks, click File -> Generate

Source.

c、 Select Sources as storage path, specify the file name then click OK.

600
PLC Connection Guide
d、 Select the objects to be exported then click OK.

e、 Under Sources there will be names of the saved files, select Export Source
to build *.AWL file.

601
PLC Connection Guide
The generated *.dif and *.AWL files can be imported in EasyBuilder8000/EasyBuilderPro
System Parameter Settings, by clicking Import Tag.

Tag information successfully imported.

Driver Version:
Version Date Description
V1.40 May/25/2011 Added registers: MB & DBBn

602
PLC Connection Guide

Siemens TI505
Supported Series: SIMATIC TI505 Series PLCs: TI520, TI525, TI530, TI535, TI545, TI555,
TI560, TI565, TI575. Use NITP protocol in a point-to-point, single master, single slave
format.

Website: http://www.siemens.com/entry/cc/en/

HMI Setting:
Parameters Recommended Options Notes
PLC type SIMATIC TI505 NITP protocol
PLC I/F RS232 RS232,
Baud rate 19200 RS485(4W)
19200
Data bits 7 7
Parity Odd Odd
Stop bits 1 1
PLC sta. no. 0 Does not apply

Device Address:
Bit/Word Device type Format Range Memo
B CR DDDDD 1 ~ 65535 Internal Relay
B X DDDDD 1 ~ 65535 Discrete Input Coils
B Y DDDDD 1 ~ 65535 Discrete Output Coils
W V DDDDD 1 ~ 65535 User Data Registers
W STW DDDDD 1 ~ 65535 Status Word Registers
W TCP DDDDD 1 ~ 65535 Timer/Counter Preset Values
W TCC DDDDD 1 ~ 65535 Timer/Counter Current Values
W WX DDDDD 1 ~ 65535 Word Discrete Inputs
W WY DDDDD 1 ~ 65535 Word Discrete Outputs

603
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
SIMATIC TI505 RS232 : 9P D-Sub to 25P D-Sub
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 25P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 2 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 7 GND
4 RTS
circuit
5 CTS
6 DSR
8 DCD circuit
20 DTR

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 25P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 2 TXD
3 TX 4 TX 7 TX 3 RXD
5 GND 5 GND 5 GND 7 GND
4 RTS
circuit
5 CTS
6 DSR
8 DCD circuit
20 DTR

604
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 25P D-Sub Male
D-Sub Female
9 RX 2 TXD
6 TX 3 RXD
5 GND 7 GND
4 RTS
circuit
5 CTS
6 DSR
8 DCD circuit
20 DTR

The following represents the cable end connector.

SIMATIC TI505 RS232 : 9P D-Sub to 9P D-Sub
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS
1 DCD
4 DTR circuit
6 DSR

605
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND
7 RTS 7 RTS
8 CTS 8 CTS
1 DCD 1 DCD
4 DTR 4 DTR
6 DSR

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
7 RTS
circuit
8 CTS
1 DCD
4 DTR circuit
6 DSR

606
PLC Connection Guide
The following represents the cable end connector.
SIMATIC TI505 RS485 4W : 9P D-Sub to 9P D-Sub
eMT3000 series
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- 7 DO (-)
2 RX+ 1 DO (+)
3 TX- 8 DI (-)
4 TX+ 5 DI (+)
5 GND 6 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- 7 DO (-)
2 RX+ 1 DO (+)
3 TX- 8 DI (-)
4 TX+ 5 DI (+)
5 GND 6 GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Female Male
1 RX- 7 DO (-)
2 RX+ 1 DO (+)
3 TX- 8 DI (-)
4 TX+ 5 DI (+)
5 GND 6 GND

607
PLC Connection Guide

Driver Version:
Version Date Description
V1.10 Apr/22/2009

608
PLC Connection Guide

Siemens TI565/C400

Website: http://www.siemens.com/entry/cc/en/

HMI Setting:
Parameters Recommended Options Notes
PLC type SIMATIC TI565/C400
PLC I/F RS232 RS232, RS485(4W)
Baud rate 19200 19200
Data bits 7 7
Parity Odd Odd
Stop bits 1 1
PLC sta. no. 0 Does not apply

Device Address:
Bit/Word Device type Format Range Memo
B CR DDDDD 1 ~ 65535 Internal Relay
B X DDDDD 1 ~ 65535 Discrete Input Coils
B Y DDDDD 1 ~ 65535 Discrete Output Coils
B V_Bit DDDDDdd 100 ~ 6553515 User Data Registers
W V DDDDD 1 ~ 65535 User Data Registers
W STW DDDDD 1 ~ 65535 Status Word Registers
W TCP DDDDD 1 ~ 65535 Timer/Counter Preset Values
W TCC DDDDD 1 ~ 65535 Timer/Counter Current Values
W WX DDDDD 1 ~ 65535 Word Discrete Inputs
W WY DDDDD 1 ~ 65535 Word Discrete Outputs

609
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 25P D-Sub: RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 25P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 2 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 7 GND
4 RTS
circuit
5 CTS
6 DSR
8 DCD circuit
20 DTR

MT6000/8000 series except MT6050i/MT8050i

610
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 25P D-Sub Male
D-Sub Female
9 RX 2 TXD
6 TX 3 RXD
5 GND 7 GND
4 RTS
circuit
5 CTS
6 DSR
8 DCD circuit
20 DTR

The following represents the cable end connector.

9P D-Sub to 9P D-Sub: RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS
1 DCD
4 DTR circuit
6 DSR

611
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS
1 DCD
4 DTR circuit
6 DSR

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
7 RTS
circuit
8 CTS
1 DCD
4 DTR circuit
6 DSR

612
PLC Connection Guide
The following represents the cable end connector.
9P D-Sub to 9P D-Sub: RS-485 4W
eMT3000 series
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- 7 DO (-)
2 RX+ 1 DO (+)
3 TX- 8 DI (-)
4 TX+ 5 DI (+)
5 GND 6 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- 7 DO (-)
2 RX+ 1 DO (+)
3 TX- 8 DI (-)
4 TX+ 5 DI (+)
5 GND 6 GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Female Male
1 RX- 7 DO (-)
2 RX+ 1 DO (+)
3 TX- 8 DI (-)
4 TX+ 5 DI (+)
5 GND 6 GND

613
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 Aug/31/2011 Driver released.

614
PLC Connection Guide

SSTC SSD Series

Supported Series: SSTC SSD Series

HMI Setting:
Parameters Recommended Options Notes
PLC type SSTC SSD Series
PLC I/F RS232 RS232/RS485 2W
Baud rate 19200 9600~115200
Data bits 8 8
Parity None None,Odd
Stop bits 1 1
PLC sta. no. 1 1~32

Device Address:
Bit/Word Device Type Format Range Memo
W ID DDDDD 0 ~ 99999
W ID_35000 DDDDD 35000 String
W ID_35001 DDDDD 35001 String

ID Address List:
ID No. Data Length Data Type Write / Read Decimal Place*
1 BYT2 UDEC Yes/Yes 1
30 BYT4 HEX No/Yes Hex
36 BYT4 SDEC Yes/Yes 0.0001
38 BYT4 UDEC Yes/Yes 0.0001
39 BYT4 SDEC Yes/Yes 0.0001
40 BYT4 SDEC No/Yes 0.0001
41 BYT4 SDEC No/Yes 0.0001
43 BYT2 UDEC Yes/Yes 1
47 BYT4 SDEC Yes/Yes 1
48 BYT4 SDEC Yes/Yes 1
49 BYT4 SDEC Yes/Yes 1
50 BYT4 SDEC Yes/Yes 1
615
PLC Connection Guide
ID No. Data Length Data Type Write / Read Decimal Place*
51 BYT4 SDEC Yes/Yes 1
53 BYT4 SDEC Yes/Yes 1
55 BYT2 UDEC Yes/Yes 1
57 BYT4 UDEC Yes/Yes 1
80 BYT2 SDEC Yes/Yes 0.1
82 BYT2 UDEC Yes/Yes 0.1
83 BYT2 SDEC Yes/Yes 0.1
84 BYT2 SDEC No/Yes 0.1
85 BYT2 UDEC Yes/Yes 1
100 BYT2 UDEC Yes/Yes 1
101 BYT2 UDEC Yes/Yes 0.1
102 BYT2 UDEC Yes/Yes 0.1
103 BYT4 SDEC Yes/Yes 1
104 BYT2 UDEC Yes/Yes 1
109 BYT4 UDEC Yes/Yes 0.001
110 BYT4 UDEC No/Yes 0.001
111 BYT4 UDEC Yes/Yes 0.001
112 BYT4 UDEC No/Yes 0.001
113 BYT4 UDEC Yes/Yes 0.0001
116 BYT4 UDEC Yes/Yes 1
124 BYT4 SDEC Yes/Yes 0.0001
125 BYT4 SDEC Yes/Yes 0.0001
126 BYT2 SDEC Yes/Yes 0.1
136 BYT4 SDEC Yes/Yes 1
137 BYT4 SDEC Yes/Yes 1
147 BYT2 HEX Yes/Yes Hex
150 BYT4 SDEC Yes/Yes 1
153 BYT4 SDEC Yes/Yes 1
154 BUT2 HEX Yes/Yes Hex
157 BYT4 SDEC Yes/Yes 0.0001
159 BYT4 UDEC Yes/Yes 1
173 BYT4 SDEC Yes/Yes 1
193 BYT2 UDEC Yes/Yes 1
209 BYT4 UDEC Yes/Yes 0.0001

616
PLC Connection Guide
ID No. Data Length Data Type Write / Read Decimal Place*
210 BYT4 UDEC Yes/Yes 0.0001
211 BYT2 UDEC Yes/Yes 0.1
212 BYT2 UDEC Yes/Yes 0.1
222 BYT4 SDEC Yes/Yes 1
225 BYT2 HEX Yes/Yes Hex
228 BYT4 UDEC Yes/Yes 1
230 BYT4 UDEC Yes/Yes 1
268 BYT4 UDEC Yes/Yes 1
278 BYT4 UDEC Yes/Yes 1
32768 BYT2 UDEC Yes/Yes 0.1
32769 BYT4 UDEC Yes/Yes 0.001
32770 BYT4 UDEC Yes/Yes 0.001
32771 BYT2 UDEC Yes/Yes 0.1
32772 BYT4 UDEC Yes/Yes 0.0001
32773 BYT4 HEX Yes/Yes Hex
32774 BYT2 UDEC Yes/Yes 0.1
32775 BYT2 UDEC Yes/Yes 1
32776 BYT2 UDEC Yes/Yes 1
32777 BYT2 SDEC Yes/Yes 0.1
32778 BYT4 SDEC Yes/Yes 0.0001
32779 BYT4 SDEC Yes/Yes 0.0001
32780 BYT4 UDEC Yes/Yes 0.1
32781 BYT4 UDEC Yes/Yes 0.1
32782 BYT4 UDEC Yes/Yes 0.1
32783 BYT2 UDEC Yes/Yes 1
32784 BYT4 SDEC Yes/Yes 1
32785 BYT2 UDEC Yes/Yes 1
32786 BYT4 SDEC Yes/Yes 1
32787 BYT4 UDEC Yes/Yes 1
32788 BYT4 SDEC Yes/Yes 1
32789 BYT4 UDEC Yes/Yes 1
32790 BYT4 SDEC Yes/Yes 1
32791 BYT4 UDEC Yes/Yes 1
32792 BYT4 SDEC Yes/Yes 1

617
PLC Connection Guide
ID No. Data Length Data Type Write / Read Decimal Place*
32793 BYT4 UDEC Yes/Yes 1
32794 BYT4 SDEC Yes/Yes 1
32797 BYT4 HEX No/Yes Hex
32798 BYT4 HEX No/No Hex
32799 BYT4 HEX No/No Hex
32800 BYT4 HEX Yes/Yes Hex
32801 BYT4 HEX Yes/Yes Hex
32802 BYT4 HEX Yes/Yes Hex
32803 BYT4 HEX Yes/Yes Hex
32804 BYT4 HEX Yes/Yes Hex
32805 BYT4 HEX Yes/Yes Hex
32806 BYT4 UDEC Yes/Yes 1
32807 BYT4 UDEC Yes/Yes 1
32808 BYT4 UDEC Yes/Yes 1
32809 BYT4 UDEC Yes/Yes 1
32836 BYT2 UDEC No/Yes 1
32845 BYT2 UDEC Yes/Yes 1
32846 BYT2 SDEC Yes/Yes 1
32847 BYT2 SDEC Yes/Yes 1
32848 BYT2 UDEC Yes/Yes 1
32849 BYT2 SDEC Yes/Yes 1
32850 BYT2 SDEC Yes/Yes 1
32851 BYT2 SDEC Yes/Yes 1
32852 BYT2 SDEC Yes/Yes 1
32853 BYT2 SDEC Yes/Yes 1
32854 BYT2 SDEC Yes/Yes 1
32865 BYT2 UDEC Yes/Yes 1
32866 BYT2 UDEC Yes/Yes 1
32867 BYT2 UDEC Yes/Yes 1
32868 BYT2 UDEC Yes/Yes 1
32874 BYT2 UDEC Yes/Yes 1
32875 BYT2 UDEC Yes/Yes 1
32876 BYT2 UDEC Yes/Yes 1
32877 BYT2 UDEC Yes/Yes 1

618
PLC Connection Guide
ID No. Data Length Data Type Write / Read Decimal Place*
32880 BYT2 UDEC Yes/Yes 1
32881 BYT2 UDEC Yes/Yes 1
32882 BYT2 UDEC Yes/Yes 1
32883 BYT2 UDEC Yes/Yes 1
32891 BYT2 UDEC Yes/Yes 1
32892 BYT4 UDEC Yes/Yes 1
32893 BYT4 UDEC Yes/Yes 1
32922 BYT2 UDEC Yes/Yes 1
32925 BYT2 HEX Yes/Yes Hex
32926 BYT2 HEX Yes/Yes Hex
32927 BYT2 HEX Yes/Yes Hex
32928 BYT2 UDEC Yes/Yes 0.1
32929 BYT2 UDEC Yes/Yes 0.1
32934 BYT2 UDEC Yes/Yes 1
32935 BYT2 UDEC Yes/Yes 0.1
32936 BYT4 HEX Yes/Yes Hex
32940 BYT4 SDEC Yes/Yes 1
32947 BYT4 UDEC Yes/Yes 1
32952 BYT4 UDEC Yes/Yes 1
32953 BYT2 HEX Yes/Yes Hex
32956 BYT2 UDEC Yes/Yes 1
32958 BYT2 UDEC Yes/Yes 1
32959 BYT2 UDEC Yes/Yes 1
32964 BYT2 UDEC Yes/Yes 1
32966 BYT2 SDEC Yes/Yes 1
32967 BYT2 UDEC Yes/Yes 1
32968 BYT2 UDEC Yes/Yes 0.1
32978 BYT2 UDEC Yes/Yes 1
32979 BYT2 UDEC Yes/Yes 1
32980 BYT2 UDEC Yes/Yes 1
32981 BYT2 UDEC Yes/Yes 1
32992 BYT2 UDEC Yes/Yes 0.1
32993 BYT2 UDEC Yes/Yes 0.1
33700 BYT2 UDEC Yes/Yes 1

619
PLC Connection Guide
ID No. Data Length Data Type Write / Read Decimal Place*
33701 BYT2 UDEC Yes/Yes 1
33702 BYT2 UDEC Yes/Yes 1
33703 BYT2 UDEC Yes/Yes 1
33704 BYT2 UDEC Yes/Yes 1
33705 BYT2 UDEC Yes/Yes 1
33706 BYT2 UDEC Yes/Yes 1
33707 BYT2 UDEC Yes/Yes 1
33708 BYT2 UDEC Yes/Yes 1
33709 BYT2 UDEC Yes/Yes 1
33710 BYT2 UDEC Yes/Yes 1
33711 BYT2 UDEC Yes/Yes 1
33712 BYT2 UDEC Yes/Yes 1
33713 BYT2 UDEC Yes/Yes 1
33714 BYT2 UDEC Yes/Yes 1
33721 BYT2 UDEC Yes/Yes 1
33722 BYT2 UDEC Yes/Yes 1
33724 BYT2 UDEC Yes/Yes 1
33725 BYT2 UDEC Yes/Yes 1
33729 BYT2 UDEC Yes/Yes 1
33730 BYT2 UDEC Yes/Yes 1
33731 BYT2 UDEC Yes/Yes 1
33732 BYT2 UDEC No/Yes 1
33800 BYT2 UDEC Yes/Yes 1
33801 BYT2 UDEC Yes/Yes 1
33802 BYT2 UDEC Yes/Yes 1
33803 BYT2 UDEC Yes/Yes 1
33804 BYT2 UDEC Yes/Yes 1
33805 BYT2 UDEC Yes/Yes 1
33806 BYT2 UDEC Yes/Yes 1
33807 BYT2 UDEC Yes/Yes 1
33808 BYT2 UDEC Yes/Yes 1
33809 BYT2 UDEC Yes/Yes 1
33810 BYT2 UDEC Yes/Yes 1
33811 BYT2 UDEC Yes/Yes 1

620
PLC Connection Guide
ID No. Data Length Data Type Write / Read Decimal Place*
33812 BYT2 UDEC Yes/Yes 1
33813 BYT2 UDEC Yes/Yes 1
33814 BYT2 UDEC Yes/Yes 1
33815 BYT2 UDEC Yes/Yes 1
33816 BYT2 UDEC Yes/Yes 1
33817 BYT2 UDEC Yes/Yes 1
33818 BYT2 UDEC Yes/Yes 1
33819 BYT2 UDEC Yes/Yes 1
33820 BYT2 UDEC Yes/Yes 1
33839 BYT2 UDEC Yes/Yes 1
33840 BYT2 UDEC Yes/Yes 1
33859 BYT2 UDEC Yes/Yes 1
33860 BYT2 UDEC Yes/Yes 1
33869 BYT2 UDEC Yes/Yes 1
33880 BYT2 UDEC Yes/Yes 1
33889 BYT2 UDEC Yes/Yes 1
33890 BYT2 UDEC Yes/Yes 1
33899 BYT2 UDEC Yes/Yes 1
34000 BYT2 UDEC Yes/Yes 1
34001 BYT2 UDEC Yes/Yes 1
34002 BYT2 UDEC Yes/Yes 1
34003 BYT2 UDEC Yes/Yes 1
34004 BYT2 UDEC Yes/Yes 1
34005 BYT2 UDEC Yes/Yes 1
34006 BYT2 UDEC Yes/Yes 1
34007 BYT2 UDEC Yes/Yes 1
34008 BYT2 UDEC Yes/Yes 1
34009 BYT2 UDEC Yes/Yes 1
34010 BYT2 UDEC Yes/Yes 1
34011 BYT2 UDEC Yes/Yes 1
34012 BYT2 UDEC Yes/Yes 1
34013 BYT2 UDEC Yes/Yes 1
34014 BYT2 UDEC Yes/Yes 1
34015 BYT2 UDEC Yes/Yes 1

621
PLC Connection Guide
ID No. Data Length Data Type Write / Read Decimal Place*
34016 BYT2 UDEC Yes/Yes 1
34017 BYT2 UDEC Yes/Yes 1
34018 BYT2 UDEC Yes/Yes 1
34019 BYT2 UDEC Yes/Yes 1
34023 BYT2 UDEC Yes/Yes 1
34025 BYT2 UDEC Yes/Yes 1
34042 BYT2 UDEC Yes/Yes 1
34043 BYT2 UDEC Yes/Yes 0.01
34044 BYT2 UDEC Yes/Yes 0.01
34045 BYT2 UDEC Yes/Yes 0.01
34046 BYT2 UDEC Yes/Yes 0.01
34047 BYT2 UDEC Yes/Yes 0.01
34048 BYT2 UDEC Yes/Yes 0.01
34049 BYT2 UDEC Yes/Yes 0.01
34050 BYT2 UDEC Yes/Yes 0.1
34051 BYT2 UDEC Yes/Yes 0.01
34052 BYT2 UDEC Yes/Yes 0.1
34053 BYT2 UDEC Yes/Yes 1
34054 BYT2 UDEC Yes/Yes 0.1
34055 BYT2 UDEC Yes/Yes 0.1
34056 BYT2 UDEC Yes/Yes 1
34070 BYT2 UDEC Yes/Yes 1
34148 BYT2 UDEC Yes/Yes 0.001
34149 BYT2 UDEC Yes/Yes 0.1
34164 BYT2 UDEC Yes/Yes 0.01
34167 BYT2 UDEC Yes/Yes 0.01
34177 BYT2 UDEC Yes/Yes 1
34178 BYT2 UDEC Yes/Yes 1
34179 BYT2 UDEC Yes/Yes 1
34180 BYT2 UDEC Yes/Yes 1
34182 BYT4 SDEC Yes/Yes 1
35000 /* Depends on Text */ 0 ASCI No/Yes ASCII
35001 /* Depends on Text */ 0 ASCI No/Yes ASCII
35002 BYT4 HEX No/Yes 1

622
PLC Connection Guide
ID No. Data Length Data Type Write / Read Decimal Place*
35003 BYT2 HEX No/Yes Hex
35004 BYT2 UDEC No/Yes 0.1
35005 BYT2 UDEC No/Yes 0.1
35006 BYT2 UDEC No/Yes 0.1
35007 BYT2 UDEC No/Yes 0.1
35008 BYT2 UDEC No/Yes 0.1
35009 BYT2 UDEC No/Yes 0.1
35010 BYT2 UDEC No/Yes 0.1
35011 BYT2 UDEC No/Yes 1
36000 BYT2 UDEC No/Yes 1
36001 BYT2 UDEC No/Yes 1
36002 BYT4 SDEC No/Yes 1
36003 BYT4 SDEC No/Yes 1
36004 BYT4 UDEC No/Yes 1
36005 BYT4 UDEC No/Yes 1
36006 BYT2 UDEC No/Yes 1
36007 BYT2 UDEC No/Yes 1
36008 BYT2 UDEC No/Yes 1
36009 BYT2 UDEC No/Yes 1
36010 BYT2 UDEC No/Yes 1
36011 BYT2 UDEC No/Yes 1
36012 BYT4 UDEC No/Yes 1
36013 BYT4 UDEC No/Yes 1
36019 BYT2 UDEC Yes/Yes 1
36020 BYT2 UDEC Yes/Yes 1
36021 BYT2 UDEC Yes/Yes 1
36022 BYT2 UDEC Yes/Yes 1
36023 BYT2 UDEC Yes/Yes 1
36100 BYT4 UDEC Yes/Yes 1
36101 BYT4 UDEC Yes/Yes 1
36102 BYT4 UDEC Yes/Yes 1
36103 BYT4 UDEC Yes/Yes 1
36104 BYT4 UDEC Yes/Yes 1

623
PLC Connection Guide
*Note: If the decimal place of ID is 0.0001, please set [Right of decimal Pt.] of the object to
“4”.

Wiring Diagram:
The following represents the cable end connector.
RS-232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P X5 Port RS232 9P
D-Sub Female D-Sub Female D-Sub Male
2 RX 8 RX 2 TX
3 TX 7 TX 3 RX
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P X5 Port RS232 9P
D-Sub Female D-Sub Female D-Sub Male D-Sub Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 3 RX
5 GND 5 GND 5 GND 5 GND

624
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P X5 Port RS232 9P
D-Sub Female D-Sub Male
9 RX 2 TX
6 TX 3 RX
5 GND 5 GND

The following represents the cable end connector.

RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W X5 Port RS485 2W 9P
9P D-Sub Male 9P D-Sub Male D-Sub Male
1 RX- 6 Data- 4 RS485-
2 RX+ 9 Data+ 1 RS485+
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W X5 Port RS485 2W 9P
9P D-Sub Male 9P D-Sub Male D-Sub Male
1 RX- 6 Data- 4 RS485-
2 RX+ 9 Data+ 1 RS485+
5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W X5 Port RS485 2W 9P
9P D-Sub Female 9P D-Sub Female D-Sub Male
1 RX- 7 Data- 4 RS485-
2 RX+ 8 Data+ 1 RS485+
5 GND 5 GND 5 GND

625
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 Mar/27/2012 Driver released.
The newly supported software SSTS_PAS_V2.2 supports ID
V1.10 May/14/2012
address.

626
PLC Connection Guide

TECHSOFT Intelligent Servo

Supported Series: Intelligent Servo supports IDM640, IDM240.

Website: http://www.techsoftmotion.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Intelligent Servo
PLC I/F RS232
Baud rate 9600 9600~115200
Data bits 8 7 or 8
Parity None Even, Odd, None
Stop bits 1 1 or 2
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
W Register_32bit HHHH 0 ~ 270f 32bit signed
DW Register_H HHHH 0 ~ 270f 32bit Hex
W UPD HHHHH 0 ~ 1869f Send UDP command
W STOP HHHHH 0 ~ 1869f Send STOP command

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P Servo RS232 D-Sub
D-Sub Female D-Sub Female Male
2 RX 8 RX 2 TD
3 TX 7 TX 3 RD
5 GND 5 GND 5 GND

627
PLC Connection Guide

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P Servo RS232 D-Sub
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 2 TD
3 TX 4 TX 7 TX 3 RD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P Servo RS232 D-Sub
D-Sub Female Male
9 RX 2 TD
6 TX 3 RD
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Nov/06/2009 Driver released.

628
PLC Connection Guide

TECO Inverter
Supported Series: TECO Inverter series, 7300CV model.

HMI Setting:
Parameters Recommended Options Notes
PLC type TECO Inverter
PLC I/F RS232 RS232/RS485
Baud rate 38400
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
B 0x DDDDD 1 ~ 65535 Output Bit
B 1x DDDDD 1 ~ 65535 Input Bit (read only)
B 3x_Bit DDDDDdd 100 ~ 6553515 Input Register Bit (read only)
B 4x_Bit DDDDDdd 100 ~ 6553515 Output Register Bit
B 6x_Bit DDDDDdd 100 ~ 6553515
B 0x (0x0f) DDDDD 1 ~ 65535 Write Multiple Coils
W 3x DDDDD 1 ~ 65535 Input Register (read only)
W 4x DDDDD 1 ~ 65535 Output Register
DW 5x DDDDD 1 ~ 65535 4x Double Word Swap
W 6x DDDDD 1 ~ 65535 4x Single Word Write

629
PLC Connection Guide

Wiring Diagram:

The following represents the cable end connector.

9P D-Sub to 9P D-Sub:
eMT3000 series
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
2 RX 2 TX
3 TX 3 RX
5 GND 5 GND
7 RTS 7 VCC

630
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
2 RX 2 TX
3 TX 3 RX
5 GND 5 GND
7 RTS 7 VCC

Driver Version:
Version Date Description
V1.00 Jul/27/2009 Driver released.

631
PLC Connection Guide

TECO TP02 Series

Supported Series: TAIAN TP02 series
Website: http://www.taian-technology.com

HMI Setting:
Parameters Recommended Options Notes
PLC type TECO TP02 Series
MMI 422 port: 4W; RS485
PLC I/F RS485 4W/2W RS485 4W/2W
terminals: 2W
Baud rate 19200 9600, 19200, 38400
Data bits 7 7, 8
Parity Even Even, Odd, None
Stop bits 2 1, 2
PLC sta. no. 1 0-255

PLC Setting:
RS422 port: WS041=120, WS042=1;
RS485 terminals: WS044=120, WS045=1.

Device Address:
Bit/Word Device type Format Range Memo
B X DDD 1 ~ 384 Input relay
B Y DDD 1 ~ 384 Output relay
B C DDDD 1 ~ 2048 Auxiliary relay

X DDD Input register (must be 1 or a

W 1 ~ 369
multiple of plus 1)
Output register (must be 1 or
W Y DDD 1 ~ 369
a multiple of plus 1)
W V DDDD 1 ~ 1024 Auxiliary register
W D DDDD 1 ~ 2048 Auxiliary register
W WS DDD 1 ~ 128 System register
Auxiliary relay register (must
W C DDDD 1 ~ 2033
be 1 or a multiple of plus 1)
W WC DDD 1 ~ 912 Constant register

632
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
TP02 Series MMI RS422 port : 9P D-Sub to 9P D-Sub
eMT3000 series
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- 8 TX-
2 RX+ 3 TX+
3 TX- 7 RX-
4 TX+ 2 RX+
5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- 8 TX-
2 RX+ 3 TX+
3 TX- 7 RX-
4 TX+ 2 RX+
5 GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Female Male
1 RX- 8 TX-
2 RX+ 3 TX+
3 TX- 7 RX-
4 TX+ 2 RX+
5 GND

633
PLC Connection Guide
The following represents the cable end connector.
TP02 Series RS485 Terminal : 9P D-Sub to 9P D-Sub
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W Terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- T/R-
2 RX+ 9 Data+ T/R+
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W Terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- T/R-
2 RX+ 9 Data+ T/R+
5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W Terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- T/R-
2 RX+ 8 Data+ T/R+
5 GND 5 GND

Driver Version:
Version Date Description
V1.10 Jan/25/2010

634
PLC Connection Guide

TECO TP03 Series

Supported Series: TECO (TAIAN TP03) series PLC.

Website: http://www.teco.com.tw/sa/en/

HMI Setting:
Parameters Recommended Options Notes
PLC type TECO TP03 Series
PLC I/F RS485 4W
Baud rate 19200 9600, 19200
Data bits 8 8
Parity None Even, Odd, None
Stop bits 2 1
PLC sta. no. 1 1-31

Device Address:
Bit/Word Device type Format Range Memo
B C DDDD 0 ~ 9999
B M DDDD 0 ~ 9999
B S DDDD 0 ~ 9999
B T DDDD 0 ~ 9999
B X OOO 0 ~ 377
B Y OOO 0 ~ 377
W D DDDD 0 ~ 9999
W V DDDD 0 ~ 9999
W Z DDDD 0 ~ 9999
W T_Curent DDDD 0 ~ 9999
W C_Curent DDDD 0 ~ 9999
W T_Preset DDDD 0 ~ 9999
W C_Preset DDDD 0 ~ 9999

635
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 4W RS485 4W 8P Mini-DIN
9P D-Sub Male Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 8P Mini-DIN
9P D-Sub Male Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 8P Mini-DIN
9P D-Sub Female Male
1 RX- 4 TX-
2 RX+ 7 TX+
3 TX- 1 RX-
4 TX+ 2 RX+
5 GND 3 GND

636
PLC Connection Guide

Driver Version:
Version Date Description
V1.10 Nov/13/2009

637
PLC Connection Guide

TINHAO

Website: www.chinastrand.com

HMI Setting:
Parameters Recommended Options Notes
PLC type TINHAO
PLC I/F RS485 2W
Baud rate 19200
Data bits 8
Parity None
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
W Commend1 DDD 0 ~ 255
W Commend2 DDD 0 ~ 255
W Commend3 DDD 0 ~ 255
W Commend4 DDD 0 ~ 255
W Commend5 DDD 0 ~ 255
W Commend6 DDD 0 ~ 255
W Commend7 DDD 0 ~ 255
W Commend8 DDD 0 ~ 255
W Commend9 DDD 0 ~ 255
W Commend10 DDD 0 ~ 255
W Commend11 DDD 0 ~ 255
W Commend12 DDD 0 ~ 255
W Commend13 DDD 0 ~ 255
W Commend14 DDD 0 ~ 255
W Commend15 DDD 0 ~ 255
W Commend16 DDD 0 ~ 255
W Commend17 DDD 0 ~ 255
W Commend18 DDD 0 ~ 255

638
PLC Connection Guide

Bit/Word Device type Format Range Memo

W Commend19 DDD 0 ~ 255
W Commend20 DDD 0 ~ 255
W Commend21 DDD 0 ~ 255
W Commend22 DDD 0 ~ 255

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND

639
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Oct/14/2011 Driver released.

640
PLC Connection Guide

Toptek Topvert
Supported Series: TOPVERT G1/H1/P1 series.

Website: http://www.toptek.biz/

HMI Setting:
Parameters Recommended Options Notes
PLC type Toptek Topvert
PLC I/F RS485 2W
Baud rate 9600
Data bits 7
Parity None
Stop bits 2
PLC sta. no. 1

Online simulator YES Broadcast command YES

Extend address mode YES Broadcast station no. 0

PLC Setting:
Communication mode Pr 7-15 = 0 (7, N, 2 ASCII)

Device Address:
Bit/Word Device type Format Range Memo
G=Groups, F=Function no.
B PR_Bit DDDDDdd 0 ~ 6553515 dd=0~15 bit no.

W PR DDDDD 0 ~ 65535 G=Groups, F=Function no.

641
PLC Connection Guide

Note:
Max.read-command size (words): 16
Max.write-command size (words): 1
For G1/H1/P1 Series Inverter, if standard parameter address is in decimal= 100*G+F:
G=Group (parameter group code0~9); F=Function no. (parameter number 0~99)
For example: Pr5-20 (decimal Dec.) parameter address is expressed as 100*5+20=520.

Parameter (PrX-XX) Address (decimal)

0-00 0*100+0=0
0-14 0*100+14=14
1-00 1*100+0=100

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W Terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- SG-
2 RX+ 9 Data+ SG+
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W Terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- SG-
2 RX+ 9 Data+ SG+
5 GND 5 GND

642
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W Terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- SG-
2 RX+ 8 Data+ SG+
5 GND 5 GND

Driver Version:
Version Date Description
V1.00 Dec/08/2010 Driver released.

643
PLC Connection Guide

TOSHIBA T Series
Supported Series: Toshiba T series, S2E.

Website: http://www.tic.toshiba.com

HMI Setting:
Parameters Recommended Options Notes
PLC type TOSHIBA T Series
PLC I/F RS232 RS232/RS485 In accordance with PLC port
9600, 19200, 38400,
Baud rate 9600
57600, 115200
Data bits 8 7,8
Parity Odd Even, Odd, None
Stop bits 1 1, 2
Must be same as the PLC
PLC sta. no. 0 0-255
setting

Online simulator YES Extend address mode YES

PLC Setting:
Communication mode Must set PLC node ID

Device Address:
Bit/Word Device type Format Range Memo
B X DDDDh 0 ~ 4095f Input Bit
B Y DDDDh 0 ~ 4095f Output Bit
B R DDDDh 0 ~ 8191f Auxiliary Bit
B S DDDDh 0 ~ 4095f Special Bit
B L DDDDh 0 ~ 4095f
B Z DDDDh 0 ~ 8191f
W T DDD 0 ~ 999 Timer Register
W C DDD 0 ~ 511 Counter Register
W D DDDD 0 ~ 8191 Data Memory

644
PLC Connection Guide
Bit/Word Device type Format Range Memo
W SW DDD 0 ~ 255 Special Register
W XW DDD 0 ~ 255 Input Register
W YW DDD 0 ~ 255 Output Register
W RW DDD 0 ~ 999 Auxiliary Register
W LW DDD 0 ~ 255
W W DDDD 0 ~ 1023
W F DDDD 0 ~ 8191

Wiring Diagram:
The following represents the cable end connector.
Toshiba T1 PRG RS232 : 9P D-Sub to 8P Mini-DIN
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 8P Mini-DIN
D-Sub Female D-Sub Female Male
2 RX 8 RX 6 TXD
3 TX 7 TX 8 RXD
5 GND 5 GND 5 GND
4 RTS
circuit
7 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 8P Mini-DIN
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 6 TXD
3 TX 4 TX 7 TX 8 RXD
5 GND 5 GND 5 GND 5 GND
4 RTS
circuit
7 CTS

645
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 8P Mini-DIN
D-Sub Female Male
9 RX 6 TXD
6 TX 8 RXD
5 GND 5 GND
4 RTS
circuit
7 CTS

The following represents the cable end connector.

Toshiba T2 PRG RS232 : 9P D-Sub to 9P D-Sub
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

646
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
7 RTS
circuit
8 CTS

The following represents the cable end connector.

Toshiba T2 LINK Port RS485 4W : 9P D-Sub to 15P D-Sub
eMT3000 series
COM1 RS485 4W RS485 4W 15P D-Sub
9P D-Sub Male Male
1 RX- 11 TXB
2 RX+ 3 TXA
3 TX- 10 RXB
4 TX+ 2 RXA
5 GND 7 SG
5 RTSA
circuit
4 CTSA
13 RTSB
circuit
12 CTSB

647
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 4W RS485 4W 15P D-Sub
9P D-Sub Male Male
1 RX- 11 TXB
2 RX+ 3 TXA
3 TX- 10 RXB
4 TX+ 2 RXA
5 GND 7 SG
5 RTSA
circuit
4 CTSA
13 RTSB
circuit
12 CTSB

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 15P D-Sub
9P D-Sub Female Male
1 RX- 11 TXB
2 RX+ 3 TXA
3 TX- 10 RXB
4 TX+ 2 RXA
5 GND 7 SG
5 RTSA
circuit
4 CTSA
13 RTSB
circuit
12 CTSB

Driver Version:
Version Date Description
TOSHIBA T Series driver can now correctly read and write
V1.20 May/13/2011
“L”, “LW”, “F” address types.

648
PLC Connection Guide

TOSHIBA VF-S11
Supported Series: Toshiba Invertor Protocol (ASCII code).

HMI Setting:
Parameters Recommended Options Notes
PLC type TOSHIBA VF-S11
PLC I/F RS485 2W RS422, RS485
Baud rate 9600 9600, 19200
Data bits 8 7 or 8
Parity Even Even, Odd, None
Stop bits 1 1 or 2
PLC sta. no. 0 0-99

Online simulator YES Extend address mode YES

Broadcast command YES

Device Address:
Bit/Word Device type Format Range Memo
B Cmd. No B HHHHdd 0 ~ 270f15
W Cmd. No HHHH 0 ~ ffff Parameters and data memory

Wiring Diagram:
Note:
Before connecting with VF-S11, make sure the SW1 of both sides are in the correct
position. (SW1: wiring method selector switch)

649
PLC Connection Guide

RS-485
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P RJ45
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 5 Data-
2 RX+ 9 Data+ 4 Data+
5 GND 5 GND 8 Gnd

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 8P RJ45
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 5 Data-
2 RX+ 9 Data+ 4 Data+
5 GND 5 GND 8 Gnd

650
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 8P RJ45
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 5 Data-
2 RX+ 8 Data+ 4 Data+
5 GND 5 GND 8 Gnd

Driver Version:
Version Date Description
V1.20 Aug/31/2009

651
PLC Connection Guide

TOSHIBA MACHINE Provisor TC200

Supported Series: TOSHIBA MACHINE CO., JAPAN

WebSite: http://www.toshiba-machine.co.jp

HMI Setting:
Parameters Recommended Options Notes
PLC type TOSHIBA MACHINE Provisor TC200
PLC I/F RS232 RS232 In accordance with PLC port
Baud rate 9600 9600, 19200
Data bits 8 7,8
Parity None Even, Odd, None
Stop bits 1 1, 2

Device Address:
Bit/Word Device type Format Range Memo
B R_bit HHHh 0 ~ ffff h : Bit no.(0~f)
B X_bit HHHh 0 ~ ffff h : Bit no.(0~f)
B Y_bit HHHh 0 ~ ffff h : Bit no.(0~f)
B L_bit HHHh 0 ~ ffff h : Bit no.(0~f)
W P HHH 0 ~ fff
W V HHH 0 ~ fff
W X HHH 0 ~ fff
W Y HHH 0 ~ fff
W D HHH 0 ~ fff
W R HHH 0 ~ fff
W L HHH 0 ~ fff

652
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P TC mini series RS232
D-Sub Female D-Sub Female 9P D-Sub Male
2 RX 8 RX 2 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 5 GND
7 RTS
circuit
9 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P TC mini series RS232
D-Sub Female D-Sub Female D-Sub Male 9P D-Sub Male
2 RX 6 RX 8 RX 2 TXD
3 TX 4 TX 7 TX 3 RXD
5 GND 5 GND 5 GND 5 GND
7 RTS
circuit
9 CTS

MT6050i/MT8050i
COM1 RS232 9P TC mini series RS232
D-Sub Female 9P D-Sub Male
9 RX 2 TXD
6 TX 3 RXD
5 GND 5 GND
7 RTS
circuit
9 CTS

653
PLC Connection Guide

Trio MODBUS RTU, TCP/IP

Website : http://www.triomotion.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Trio MODBUS RTU, TCP/IP
PLC I/F RS485 RS232/RS485/Ethernet
Baud rate 9600 9600~115200
Data bits 8 7, 8
Parity Even Even, Odd, None
Stop bits 1 1, 2
Port no. 502
PLC sta. no. 1 0-255

Online simulator YES Broadcast command YES

Extend address mode YES

PLC Setting:
Communication mode Modbus RTU protocol
PLC Mode 4 (16bit signed integer)

Device Address:
Bit/Word Device type Format Range Memo
B VR_Bit DDDDdd 0 ~ 102315
B Table_Bit DDDDDdd 0 ~ 3199915
W VR DDDD 0 ~ 1023
W Table DDDDD 0 ~ 31999

654
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.3
Trio : RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX TXD
3 TX 7 TX RXD
5 GND 5 GND GND
RTS
circuit
CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND
RTS
circuit
CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX TXD
6 TX RXD
5 GND GND
RTS
circuit
CTS

655
PLC Connection Guide
The following represents the cable end connector.
Trio : RS485 4W
eMT3000 series
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Female Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

656
PLC Connection Guide
The following represents the cable end connector.
Trio : RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND GND

657
PLC Connection Guide
Direct connect (crossover cable):
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 3 RX+
2 TX- Orange 6 RX-
3 RX+ White/Green 1 TX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 2 TX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Driver Version:
Version Date Description
V1.00 May/27/2011 Driver released.

658
PLC Connection Guide

Trio MODBUS RTU, TCP/IP (Mode 7)

Website : http://www.triomotion.com

HMI Setting:
Parameters Recommended Options Notes
PLC type Trio MODBUS RTU, TCP/IP (Mode 7)
PLC I/F RS485 RS232/RS485/Ethernet
Baud rate 9600 9600~115200
Data bits 8 7, 8
Parity Even Even, Odd, None
Stop bits 1 1, 2
Port no. 502
PLC sta. no. 1 0-255

Online simulator YES Broadcast command YES

Extend address mode YES

PLC Setting:
Communication mode Modbus RTU protocol
PLC 模式 7 (IEEE floating point)

Device Address:
Bit/Word Device type Format Range Memo
B VR_Bit DDDDdd 0 ~ 102331
B Table_Bit DDDDDdd 0 ~ 3199931
W VR DDDD 0 ~ 1023
W Table DDDDD 0 ~ 31999

659
PLC Connection Guide

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX TXD
3 TX 4 TX 7 TX RXD
5 GND 5 GND 5 GND GND
RTS
circuit
CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX TXD
6 TX RXD
5 GND GND
RTS
circuit
CTS

660
PLC Connection Guide
The following represents the cable end connector.
Trio : RS485 4W
eMT3000 series
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Male Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 9P D-Sub
9P D-Sub Female Male
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND GND

661
PLC Connection Guide
The following represents the cable end connector.
Trio : RS485 2W
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- D-
2 RX+ 9 Data+ D+
5 GND 5 GND GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- D-
2 RX+ 8 Data+ D+
5 GND 5 GND GND

662
PLC Connection Guide
Direct connect (crossover cable):
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 3 RX+
2 TX- Orange 6 RX-
3 RX+ White/Green 1 TX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 2 TX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Driver Version:
Version Date Description
V1.00 Apr/20/2012 Driver released.

663
PLC Connection Guide

VIGOR
Supported Series: VIGOR M Series and VB Series.

Website: http://www.vigorplc.com.tw/

HMI Setting:
Parameters Recommended Options Notes
PLC type VIGOR
PLC I/F RS232 RS232, RS485 4W
Baud rate 19200
Data bits 7
Parity Even
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
B X OOO 0 ~ 377
B Y OOO 0 ~ 377
B M DDDD 0 ~ 7999
B T DDD 0 ~ 255
B C DDD 0 ~ 255
B SM DDDD 9000 ~ 9255
W TV DDD 0 ~ 255
W CV DDD 0 ~ 199
W D DDDD 0 ~ 9255
W CV2 DDD 200 ~ 255
W SD DDDD 9000 ~ 9255

664
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
Vigor M series : RS485 4W Terminal
eMT3000 series
COM1 RS485 4W Vigor M series RS485
9P D-Sub Male 4W 6P Terminal
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND SG

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 4W Vigor M series RS485
9P D-Sub Male 4W 6P Terminal
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND SG

665
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 4W Vigor M series RS485
9P D-Sub Female 4W 6P Terminal
1 RX- TX-
2 RX+ TX+
3 TX- RX-
4 TX+ RX+
5 GND SG

The following represents the cable end connector.

Vigor M series : RS232
eMT3000 series
COM1 RS232 9P COM3 RS232 9P Vigor M series RS232
D-Sub Female D-Sub Female 9P D-Sub Male
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P Vigor M series RS232
D-Sub Female D-Sub Female D-Sub Male 9P D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND

666
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P Vigor M series RS232
D-Sub Female 9P D-Sub Male
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND

Driver Version:
Version Date Description
V1.10 Dec/30/2008

667
PLC Connection Guide

VIPA 200
HMI Setting:
Parameters Recommended Options Notes
PLC type VIPA 200
PLC I/F RS485 2w RS485 2w
The HMI which has a sticker
Baud rate 9600 9600, 19200, 187.5K “MPI187.5” on the rear
cover supports 187.5K
Data bits 8 7,8
Parity Even Even, Odd, None
Stop bits 1 1, 2
PLC sta. no. 2 1 ~ 126
Turn around
5
delay (ms)
Reserved 1 30 ACK delay time

Online simulator YES Extend address mode NO

Broadcast command NO

PLC Setting:
Communication mode Set station number to 2

668
PLC Connection Guide
Bit/Word Device type Format Range Memo
W VW_String DDDDD 0 ~ 10239 String
W VW_String_Odd DDDDD 0 ~ 10239 String
DW VD_String DDDDD 0 ~ 10239 String
DW VD_String_Odd DDDDD 0 ~ 10239 String
Byte MB DDDDD 0 ~ 10239 Byte Memory
W MW DDDDD 0 ~ 10239 Word Memory
DW MD DDDDD 0 ~ 10239 Word Memory
W MW_Odd DDDDD 0 ~ 10239 Word Memory
W T DDD 0 ~ 127 Timer
W C DDD 0 ~ 127 Counter
 Double word and floating point value must use VD device type.

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 8 D-
2 RX+ 9 Data+ 3 D+
5 GND 5 GND 5 GND

669
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 8 D-
2 RX+ 8 Data+ 3 D+
5 GND 5 GND 5 GND

Driver Version:
Version Date Description
V2.30 Aug/17/2009
V2.40 Nov/1/2011 Add device type : MD

670
PLC Connection Guide

VIPA 200 (VD any address)

HMI Setting:
Parameters Recommended Options Notes
PLC type VIPA 200 (VD any address)
PLC I/F RS485 2w RS485 2w
The HMI which has a
9600, 19200, sticker “MPI187.5” on
Baud rate 9600
187.5K the rear cover supports
187.5K
Data bits 8 7,8
Parity Even Even, Odd, None
Stop bits 1 1, 2
PLC sta. no. 2 1 ~ 126
Turn around delay 5
Reserved 1 30 ACK delay time

Online simulator YES Extend address mode NO

Broadcast command NO

PLC Setting:
Communication mode Set station number to 2

671
PLC Connection Guide

Bit/Word Device type Format Range Memo

W MW DDDDD 0 ~ 10239 Word Memory
W T DDD 0 ~ 127 Timer
W C DDD 0 ~ 127 Counter
DW MD DDDDD 0 ~ 10239 Word Memory
 Double word and floating point value must use VD device type.
 VD register can set to any value, not necessarily a multiple of 4.

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 8 D-
2 RX+ 9 Data+ 3 D+
5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 8 D-
2 RX+ 8 Data+ 3 D+
5 GND 5 GND 5 GND

672
PLC Connection Guide

Driver Version:
Version Date Description
V1.20 Nov/16/2011 Add device type : MD

673
PLC Connection Guide

VIPA 200, for ex. 214-2BT10 (Ethernet)

HMI Setting:
Parameters Recommended Options Notes
PLC type VIPA 200, for ex. 214-2BT10 (Ethernet)
PLC I/F Ethernet
Port no. 102
PLC sta. no. 1 0-31

Device Address:
Bit/Word Device type Format Range Memo
B I DDDDo 0 ~ 40957 Input (I)
B Q DDDDo 0 ~ 40957 Output (O)
B M DDDDo 0 ~ 40957 Bit Memory
B VW_Bit DDDDDo 0 ~ 102397 V Memory Bit Address
W VW DDDDD 0 ~ 10239 V Memory
DW VD DDDDD 0 ~ 10239 V Memory Double Word
W VW_String DDDDD 0 ~ 10239 String
DW VD_String DDDDD 0 ~ 10239 String
DW MD DDDDD 0 ~ 10239 Word Memory
 Double word and floating point value must use VD device type.

674
PLC Connection Guide

Driver Version:
Version Date Description
V1.20 Dec/30/2008
V1.40 Nov/15/2011 Add device type : MD

675
PLC Connection Guide

VIPA 300

HMI Setting:
Parameters Recommended Options Notes
PLC type VIPA 300
PLC I/F RS232
Must be same as the PLC setting.
19200, 38400, The HMI which has a sticker
Baud rate 9600~187.5K
187.5K MPI187.5 on the rear cover
supports 187.5K.
Data bits 8
Parity Odd
Stop bits 1
PLC sta. no. 2 Must be same as the PLC setting.

Device Address:
Bit/Word Device type Format Range Memo
B I DDDDo 0 ~ 40957 Input (I)
B Q DDDDo 0 ~ 40957 Output (O)
B M DDDDo 0 ~ 40957 Bit Memory
B DBnBit FFFFDDDDo 0 ~ 409681927 Data Register Bit
B DB0Bit ~ DDDDo 0 ~ 81927
W DB99Bit
IW DDDD 0 ~ 4095 Input (I)
W QW DDDD 0 ~ 4095 Output (O)
W MW DDDD 0 ~ 4095 Bit Memory
DW MD DDDD 0 ~ 4094
Byte MB DDDD 0 ~ 4095 Bit Memory Byte
Byte DBBn FFFFDDDD 0 ~ 40968192 Data Register Byte
Data Register
W DBn FFFFDDDD 0 ~ 40968192
(must be even)
Data Register Double Word
DW DBDn FFFFDDDD 0 ~ 40968192
(must be multiple of 4)
Data Register Double Word
W DBn_String FFFFDDDD 0 ~ 40968192
(must be multiple of 4)

676
PLC Connection Guide

Bit/Word Device type Format Range Memo

Data Register Double Word
DW DBDn_String FFFFDDDD 0 ~ 40968192
(must be multiple of 4)
Data Register
W DB0-DB99 DDDD 0 ~ 8192
(must be even)
* Double word and floating point value must use DBDn device type.

How to Import Tag:

677
PLC Connection Guide
b、 Click Export to export the edited file and click Save.

2. Building *.AWF File

a、 In Blocks create items as shown below:

b、 Open LAD/STL, FBD – Programming S7 Blocks, click File -> Generate

Source.

678
PLC Connection Guide
c、 Select Sources as storage path, specify the file name then click OK.

d、 Select the objects to be exported then click OK.

679
PLC Connection Guide
e、 Under Sources there will be names of the saved files, select Export Source
to build *.AWL file.

The generated .dif and .AWL files can be imported in EasyBuilder8000/EasyBuilderPro

System Parameter Settings, by clicking Import Tag.

Tag information successfully imported.

680
PLC Connection Guide

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
7 RTS
circuit
8 CTS

681
PLC Connection Guide
The following represents the cable end connector.
Systeme Helmholz SSW7-TS : 9P D-Sub to 9P D-Sub
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS
4 DTR
circuit
6 DSR

MT6000/8000 series except MT6050i/MT8050i

682
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
7 RTS
circuit
8 CTS
4 DTR
circuit
6 DSR

Driver Version:
Version Date Description
V3.10 May/24/2011 Added registers: MB & DBBn.

683
PLC Connection Guide

VIPA 300 MPI

HMI Setting:
Parameters Recommended Options Notes
PLC type VIPA 300 MPI
PLC I/F RS-485 2W
Only HMI with a sticker “MPI 187.5K” on the
Baud rate 187.5K
rear cover supports MPI communication.
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 2 2 ~ 31

Online simulator NO Extend address mode Yes

Broadcast command NO

Device Address:
Bit/Word Device type Format Range Memo
B I DDDDo 0 ~ 40957 Input (I)
B Q DDDDo 0 ~ 40957 Output (O)
B M DDDDo 0 ~ 40957 Bit Memory
B DBnBit FFFFDDDDo 0 ~ 409699997 Data Register Bit
DB0Bit ~
B DDDDDo 0 ~ 655327 Data Register Bit
DB99Bit
W IW DDDD 0 ~ 4095 Input (I)
W QW DDDD 0 ~ 4095 Output (O)
W MW DDDD 0 ~ 4095 Bit Memory
DW MD DDDD 0 ~ 4094
Byte MB DDDD 0 ~ 4095 Bit Memory Byte
Byte DBBn FFFFDDDD 0 ~ 40969999 Data Register
W DBn FFFFDDDD 0 ~ 40969999 Data Register (must be even)
DW DBDn FFFFDDDD 0 ~ 40969999 Data Register Double Word
W DBn_String FFFFDDDD 0 ~ 40969999
DW DBDn_String FFFFDDDD 0 ~ 40969999
W DB0 ~ DB99 DDDDD 0 ~ 65532 Data Register (must be even)
* Double word and floating point value must use DBDn device type.

684
PLC Connection Guide

Multi-HMIs-Multi-PLCs Communication Setting:

For SIEMENS S7-300 MPI driver in Multi-HMIs-Multi-PLCs communication, [Max. station

685
PLC Connection Guide
For the effectiveness of communication, users may set PLC device in STEP 7 as shown
below. In Properties MPI / Network Settings, set Highest MPI address to the number
closest to the actual device station number.

How to Import Tag:

1. Building *.dif File

a、 In “Symbols” create user-defined tag.

686
PLC Connection Guide

687
PLC Connection Guide
b、 Click Export to export the edited file and click Save.

2. Building *.AWF File

a、 In Blocks create items as shown below:

b、 Open LAD/STL, FBD – Programming S7 Blocks, click File -> Generate

Source.

688
PLC Connection Guide
c、 Select Sources as storage path, specify the file name then click OK.

d、 Select the objects to be exported then click OK.

689
PLC Connection Guide
e、 Under Sources there will be names of the saved files, select Export Source
to build *.AWL file.

The generated .dif and .AWL files can be imported in EasyBuilder8000/EasyBuilderPro

System Parameter Settings, by clicking Import Tag.

Tag information successfully imported.

690
PLC Connection Guide

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Male 9P D-Sub Male Male
1 RX- 6 Data- 8 D-
2 RX+ 9 Data+ 3 D+
5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W 9P D-Sub
9P D-Sub Female 9P D-Sub Female Male
1 RX- 7 Data- 8 D-
2 RX+ 8 Data+ 3 D+
5 GND 5 GND 5 GND

Driver Version:
Version Date Description
V1.90 May/26/2011 Added registers: MB & DBBn
i Series HMI support Multi HMIs-Multi PLCs
V2.00 Aug/19d/2011
communication.

691
PLC Connection Guide

VIPA 300S (Ethernet)

HMI Setting:
Parameters Recommended Options Notes
PLC type VIPA 300S (Ethernet)
PLC I/F Ethernet
Port no. 102
Link type PG PC, OP
Rack 0 0-7
CPU slot 3 2-31
PLC sta. no. 0 0-31

Device Address:
Bit/Word Device type Format Range Memo
B I DDDDo 0 ~ 40957 Input (I)
B Q DDDDo 0 ~ 40957 Output (O)
B M DDDDo 0 ~ 40957 Bit Memory
B DBnBit FFFFDDDDo 0 ~ 409699997
B DB0Bit-DB99Bit DDDDDo 0 ~ 655327 Data Register Bit
W IW DDDD 0 ~ 4095 Input (I)
W QW DDDD 0 ~ 4095 Output (O)
W MW DDDD 0 ~ 4095 Bit Memory
DW MD DDDD 0 ~ 4094
Data Register
W DBn FFFFDDDD 0 ~ 40969999
(must be even)
Data Register Double Word
DW DBDn FFFFDDDD 0 ~ 40969999
(must be multiple of 4)
W DBn_String FFFFDDDD 0 ~ 40969999
DW DBDn_String FFFFDDDD 0 ~ 40969999
W DB0 ~ DB99 DDDDD 0 ~ 65532 Data Register
Byte MB DDDD 0 ~ 4095 (must
Bit be even)
Memory Byte
Byte DBBn FFFFDDDD 0 ~ 40969999 Data Register Byte
* Double word and floating point value must use DBDn device type.

692
PLC Connection Guide

693
PLC Connection Guide

EasyBuilder Device Setting Steps

1. Open EasyBuilder, File/NEW, select HMI model and press [OK].

2. ”System Parameter Settings” window is shown, click [New].

3. Select “SIEMENS S7-400(ETHERNET)”.

4. Press [Settings].
5. Set S7-400 IP, Port no., Link type, Rack and CPU slot. (must match PLC settings)

694
PLC Connection Guide
6. The setting will be finished as below.

How to Import Tag:

695
PLC Connection Guide
b、 Click Export to export the edited file and click Save.

2. Building *.AWF File

a、 In Blocks create items as shown below:

b、 Open LAD/STL, FBD – Programming S7 Blocks, click File -> Generate

Source.

696
PLC Connection Guide
c、 Select Sources as storage path, specify the file name then click OK.

d、 Select the objects to be exported then click OK.

697
PLC Connection Guide
e、 Under Sources there will be names of the saved files, select Export Source
to build *.AWL file.

The generated .dif and .AWL files can be imported in EasyBuilder8000/EasyBuilderPro

System Parameter Settings, by clicking Import Tag.

Tag information successfully imported.

Driver Version:
Version Date Description
V1.40 May/25/2011 Added registers: MB & DBBn

698
PLC Connection Guide

VIPA 300S, for ex. 315-4NE12 (Ethernet)

HMI Setting:
Parameters Recommended Options Notes
PLC type VIPA 300S, for ex. 315-4NE12 (Ethernet)
PLC I/F Ethernet
Port no. 102
PLC sta. no. 1 0-31

Device Address:
Bit/Word Device type Format Range Memo
B I DDDDo 0 ~ 40957 Input (I)
B Q DDDDo 0 ~ 40957 Output (O)
B M DDDDo 0 ~ 40957 Bit Memory
B DBnBit FFFFDDDDo 0 ~ 409699997
B DB0Bit-DB99Bit DDDDDo 0 ~ 655327 Data Register Bit
W IW DDDD 0 ~ 4095 Input (I)
W QW DDDD 0 ~ 4095 Output (O)
W MW DDDD 0 ~ 4095 Bit Memory
DW MD DDDD 0 ~ 4094 Bit Memory Double Word
Data Register
W DBn FFFFDDDD 0 ~ 40969999
(must be even)
Data Register Double Word
DW DBDn FFFFDDDD 0 ~ 40969999
(must be multiple of 4)
W DBn_String FFFFDDDD 0 ~ 40969999
DW DBDn_String FFFFDDDD 0 ~ 40969999
Data Register
W DB0 ~ DB99 DDDDD 0 ~ 65532
(must be even)
Byte MB DDDD 0 ~ 4095 Bit Memory Byte
Byte DBBn FFFFDDDD 0 ~ 40969999 Data Register Byte
 Double word and floating point value must use DBDn device type.

699
PLC Connection Guide

How to Import Tag:

1. Building *.dif File

a、 In “Symbols” create user-defined tag.

700
PLC Connection Guide
b、 Click Export to export the edited file and click Save.

2. Building *.AWF File

a、 In Blocks create items as shown below:

b、 Open LAD/STL, FBD – Programming S7 Blocks, click File -> Generate

Source.

701
PLC Connection Guide
c、 Select Sources as storage path, specify the file name then click OK.

d、 Select the objects to be exported then click OK.

702
PLC Connection Guide
e、 Under Sources there will be names of the saved files, select Export Source
to build *.AWL file.

The generated .dif and .AWL files can be imported in EasyBuilder8000/EasyBuilderPro

System Parameter Settings, by clicking Import Tag.

Tag information successfully imported.

703
PLC Connection Guide

Driver Version:
Version Date Description
V2.10 May/21/2011 Added registers: MB & DBBn.

704
PLC Connection Guide

XINJE XC Series
Supported Series: XINJE XC Series

Website: http://www.xinje.com/0/index.html

HMI Setting:
Parameters Recommended Options Notes
PLC type XINJE XC Series
PLC I/F RS232 RS232
Baud rate 19200
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 1 0-255

Device Address:
Bit/Word Device type Format Range Memo
B M DDDD 0 ~ 8511
B X OOOO 0 ~ 1037
B Y OOOO 0 ~ 1037
B S DDDD 0 ~ 1023
B T DDD 0 ~ 618
B C DDD 0 ~ 634
W D DDDD 0 ~ 8511
W TD DDD 0 ~ 618
W CD DDD 0 ~ 634
W FD_1 DDDD 0 ~ 5000
W FD_2 DDDD 8000 ~ 8511

705
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
Driver Version: eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 8P Mini-Din
D-Sub Female D-Sub Female Male
2 RX 8 RX 5 TX
3 TX 7 TX 4 RX
5 GND 5 GND 8 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 8P Mini-Din
D-Sub Female D-Sub Female D-Sub Male Male
2 RX 6 RX 8 RX 5 TX
3 TX 4 TX 7 TX 4 RX
5 GND 5 GND 5 GND 8 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 8P Mini-Din
D-Sub Female Male
9 RX 5 TX
6 TX 4 RX
5 GND 8 GND

Version Date Description

V1.00 Jul/02/2009 Driver released.

706
PLC Connection Guide

YAMAHA ERCD

HMI Setting:

Parameters Recommended Options Notes

PLC type YAMAHA ERCD
PLC I/F RS232
Baud rate 9600 1200-19200
Data bits 8 7 or 8
Parity Odd None/Even/Odd
Stop bits 1 1 or 2
PLC sta. no. 0 Needn’t to set the station No.

Device Address:
Bit/Word Device type Format Range Memo
Word P DDD 0 ~ 999 Read/Write, PNT point data
Write only，RW0=program
Word SWI D 0 number，Switches program number
to run
Word ORG D 0 Write only，returns to origin
Word RESET D 0 Write only，reset program
Write only，starts automatic
Word RUN D 0
operation
Word X_ADD D 0 Write only，X＋ command
Word X_SUB D 0 Write only，X－ command
Write only，directly moves to
specified position
Word MOVD D 0
RW1=X-axis position(mm),
RW2=speed

707
PLC Connection Guide

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TX
3 TX 4 TX 7 TX 2 RX
5 GND 5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TX
6 TX 2 RX
5 GND 5 GND
7 RTS
circuit
8 CTS

708
PLC Connection Guide

Driver Version:
Version Date Description
V1.30 Jan/04/2010

709
PLC Connection Guide

YASKAWA CCMEP
Supported Series: YASKAWA CCMEP-100/ CCMEP-200
Website http://www.yaskawa.co.jp

HMI Setting:
Parameters Recommended Options Notes
PLC type YASKAWA CCMEP
PLC I/F RS485 4W
Baud rate 38400
Data bits 8
Parity Even
Stop bits 1
PLC sta. no. 1

Device Address:
Bit/Word Device type Format Range Memo
B 4_Bit DDDDDdd 100 ~ 6553515
W 4 DDDDD 1 ~ 65535

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 4W RS485 4W 8P RJ45
9P D-Sub Male Male
1 RX- 4 TX-
2 RX+ 3 TX+
3 TX- 2 RX-
4 TX+ 1 RX+
5 GND 8 GND

710
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 4W RS485 4W 8P RJ45
9P D-Sub Male Male
1 RX- 4 TX-
2 RX+ 3 TX+
3 TX- 2 RX-
4 TX+ 1 RX+
5 GND 8 GND

MT6050i/MT8050i
COM1 RS485 4W RS485 4W 8P RJ45
9P D-Sub Female Male
1 RX- 4 TX-
2 RX+ 3 TX+
3 TX- 2 RX-
4 TX+ 1 RX+
5 GND 8 GND

Driver Version:
Version Date Description
V1.00 Jun/14/2012 Driver released.

711
PLC Connection Guide

YASKAWA Memobus (MP Series Controllers)

Supported Series: YASKAWA MP2200, MP2300, MP2300S, MP9xx communication
module.
Website: http://www.yaskawa.com/

HMI Setting:
Parameters Recommended Options Notes
PLC type YASKAWA Memobus (MP Series Controllers)
RS232/RS485 2w/4w,
PLC I/F RS485/Ethernet
Ethernet
Baud rate 19200 9600~57600
Data bits 8
Parity Even
Stop bits 1
Port no. 502 default Ethernet Module Only
PLC sta. no. 1 1-31

PLC Setting:
Communication mode MEMOBUS, Slave, RTU

PLC Ethernet Setting:

1. Use MPE720 program software, open Module Configuration, double click “218IFA”.

712
PLC Connection Guide
2. In Transmision Parameters input MP2300S IP address, Subnet Mask, Gateway IP.
In Connection Parameter, CNO -1 input: Local Port=502, Node IP
address=000.000.000.000, Node Port=00000, Connect Type=TCP, Protocol
Type=MEMOBUS, Code=RTU.

3. Click MECHATROLINK to set up MP2300S PLC as Master.

4. Close all dialogs and save to MP2300S.

713
PLC Connection Guide

Note:
1. Only CNO 01 can auto communicate with one HMI. Other CNO need a ladder program
created for communication.
2. DIP SW2-2 of MP2300S must be set to OFF position during normal communication,
otherwise, IP address will be erased after reset power, and it will be unable to
communicate with HMI when set to ON position.

Device Address:
Bit/Word Device type Format Range Memo
B MB_1 DDDDh 0 ~ 9999f MB 0 ~ 9999
B MB_2 DDDDDh 100000 ~ 65534f MB 10000 ~ 65535
B IB HHHHH 0 ~ a7ff0 Read only
B IW_Bit HHHHdd 0~ a7ff15
W IW HHHH 0 ~ a7ff Read only
DW IL HHHH 0 ~ a7ff Read only
DW (F) IF HHHH 0 ~ a7ff Read only
W MW DDDDD 0 ~ 65534 Holding register
DW ML DDDDD 0 ~ 65533 Double word
DW (F) MF DDDDD 0 ~ 65533 Floating point
*: When connect via Ethernet interface the max range of IW, IL and IF would be restricted.

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 9P D-Sub: 217IF-01, 218IF-01
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 2 TX
3 TX 7 TX 3 RX
5 GND 5 GND 7 GND

714
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 2 TX
3 TX 4 TX 7 TX 3 RX
5 GND 5 GND 5 GND 7 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 2 TX
6 TX 3 RX
5 GND 7 GND

The following represents the cable end connector.

217IF-01 RS485 2W:
eMT3000 series
COM1 RS485 2W COM3 RS485 2W 217IF-01 RS485 14P
9P D-Sub Male 9P D-Sub Male Connector
1 RX- 6 Data- 2, 4 D-
2 RX+ 9 Data+ 1, 3 D+
5 GND 5 GND 14 GND

715
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W 217IF-01 RS485 14P
9P D-Sub Male 9P D-Sub Male Connector
1 RX- 6 Data- 2, 4 D-
2 RX+ 9 Data+ 1, 3 D+
5 GND 5 GND 14 GND

MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W 217IF-01 RS485 14P
9P D-Sub Female 9P D-Sub Female Connector
1 RX- 7 Data- 2, 4 D-
2 RX+ 8 Data+ 1, 3 D+
5 GND 5 GND 14 GND

The following represents the cable end connector.

217IF-01 RS4854W:
eMT3000 series
COM1 RS485 4W 217IF-01 RS422 14P
9P D-Sub Male Connector
1 RX- 2 TX-
2 RX+ 1 TX+
3 TX- 4 RX-
4 TX+ 3 RX+
5 GND 14 GND

716
PLC Connection Guide
MT6000/8000 series except MT6050i/MT8050i
COM1 RS485 4W 217IF-01 RS422 14P
9P D-Sub Male Connector
1 RX- 2 TX-
2 RX+ 1 TX+
3 TX- 4 RX-
4 TX+ 3 RX+
5 GND 14 GND

MT6050i/MT8050i
COM1 RS485 4W 217IF-01 RS422 14P
9P D-Sub Female Connector
1 RX- 2 TX-
2 RX+ 1 TX+
3 TX- 4 RX-
4 TX+ 3 RX+
5 GND 14 GND

Direct connect (crossover cable):

HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 3 RX+
2 TX- Orange 6 RX-
3 RX+ White/Green 1 TX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 2 TX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

717
PLC Connection Guide
Through a hub:
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 1 TX+
2 TX- Orange 2 TX-
3 RX+ White/Green 3 RX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 6 RX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Driver Version:
Version Date Description
V1.70 Dec/20/2010

718
PLC Connection Guide

YASKAWA MP Series Ethernet (Extension)

HMI Setting:
Parameters Recommended Options Notes
PLC type YASKAWA MP Series Ethernet (Extension)
PLC I/F Ethernet (UDP)
Port no. 10000
PLC sta. no. 1

PLC Setting:
Yaskawa PLC Communication Parameter Settings
(1) PLC Factory Communication Parameter Settings:

Item Set
IP Address 192.168.1.1
Subnet Mask 255.255.255.0
Gateway IP Address 0.0.0.0
System Port No. 10000 (UDP)
TCP Zero Window Timer Value 3 (s)
TCP Retry Time 500 (ms)
TCP Close Time 60 (s)
IP Assemble Time 30 (s)
Max. Packet Length 1500 (bytes)

(2) Setting Steps:

1. Set IP for PLC.

719
PLC Connection Guide
2. Communication parameter setting.

3. Go to Module Details and select [218IFA] for setting relevant parameters for Ethernet
transmission.

4. The settings are shown below, PLC IP can’t be repeated.

720
PLC Connection Guide
5. Download PLC communication parameters to PLC, and restart the controller.

(3) HMI Settings:

1. Select Ethernet for PLC I/F.
2. Tick [UDP].
3. Set PLC IP and Port, the default Port is 10000.

721
PLC Connection Guide

Device Address:
Bit/Word Device type Format Range Memo
B SB DDDDh 0 ~ 8191f
B IB HHHHh 0 ~ fffff
B OB HHHHh 0 ~ fffff
B MB DDDDDh 0 ~ 65534f
W SW DDDD 0 ~ 8191
W IW HHHH 0 ~ ffff
W OW HHHH 0 ~ ffff
W MW DDDDD 0 ~ 65534

722
PLC Connection Guide
Through a hub:
HMI RJ45 Male Wire Color PLC RJ45 Male
1 TX+ White/Orange 1 TX+
2 TX- Orange 2 TX-
3 RX+ White/Green 3 RX+
4 BD4+ Blue 4 BD4+
5 BD4- White/Blue 5 BD4-
6 RX- Green 6 RX-
7 BD3+ White/Brown 7 BD3+
8 BD3- Brown 8 BD3-

Driver Version:
Version Date Description
V1.10 Jul/21/2011 Driver released.

723
PLC Connection Guide

YASKAWA MP2300Siec

Website: http://www.yaskawa.com/site/home.nsf/home/home.html

HMI Setting:
Parameters Recommended Options Notes
PLC type YASKAWA MP2300Siec
PLC I/F Ethernet
Port no. 44818
Assembly Input::101 Input::101~106
instance Output:111 Output:111~116
PLC sta. no. 1

PLC Setting:
MP2300Siec-Motion Works IEC Express (YASKAWA) Settings:

Step 1. Before HMI communicates with MP2300Siec using Ethernet/IP, the Instance Input
and Instance Output of MP2300Siec device must be set correctly. Multiple Instances are
allowed to be built at one time, please click [Save] after setting.

Fig. 1 Assembly Instances

724
PLC Connection Guide
Step 2.Global Variables will automatically add in E/IP Input and Output data, Input and
Output data name and address type can be user-defined.

Fig. 2 Global Variables

Step 3. When download Project to device (MP2300Siec), please go to (Fig. 3)

Resource->Settings to access setting dialog (Fig. 4) for setting MP2300Siec IP address.

Fig. 3 Motion Works IEC Express – Settings

725
PLC Connection Guide

Fig. 4 Resource Settings

Step 4. Start compilation.

Fig. 5 Editing Screen

726
PLC Connection Guide
Step 5. Download project to device- MP2300Siec, and execute Cold.

Fig. 6 Project Downloading

EasyBuilder8000/EasyBuilder Pro Settings:

Step 1. System Parameter Settings

Open EasyBuilder8000/EasyBuilder Pro project, as shown in Fig. 7, Assembly Instance
and Size must match the software default factory settings, and please don’t select UDP.
Fig.8 below shows how HMI Input / Output address is mapped to MP2300Siec device.

Fig. 7 Instance Setting

727
PLC Connection Guide

Fig.8 HMI and MP2300Siec I/O Mapping

Step 2. Address Setting:

Instance 101 and Instance 111 are defined as 128Bytes, on the project window , WORD
objects can be used, with data typed defined as 32-Bit Unsigned, Input addresses set to
0、2、4、6…..62 for reading Instance 101 data.

Fig. 9 Address Setting

EasyBuilder8000/EasyBuilder Pro-Allen Bradley CompactLogix Tag

Data Importing and Module Defined:

Step 1. In EasyBuilder8000/EasyBuilder Pro project, when using Allen Bradley EIP driver
to import CSV file (as in Fig. 10), please open AB Data Type Editor (Fig. 11), and right click
on Module Defined to add New Data Type.

728
PLC Connection Guide

Fig. 10 RSLogix 5000 (Allen Bradley Software) Export Free Tag CSV File

Fig.11 AB Data Type Editor

Step 2. As in Fig 12, in AB Data Type Editor add Name of the new data type. The Name
must be set identically to the Data Type in Free Tag CSV file. As in Fig 14, Data Member
Name must be set identically to the AB software (as Data in Fig. 13), then click [Save] (Fig.
15).

729
PLC Connection Guide

Fig.12 AB Data Type Editor

Fig.13 Tag Information

Fig.14 Add Data Member - Name Tag Information

730
PLC Connection Guide

Fig. 15 Add Data Member-Settings - Save

Step 3. Import CSV file, Tag Information can be viewed from object address.

Fig.16 Tag Information

Device Address:
Bit/Word Device type Format Range Memo
B Input_Bit DDDDDdd 0 ~ 6553515
B Output_Bit DDDDDdd 0 ~ 6553515
DW Input DDDDD 0 ~ 65535
DW Output DDDDD 0 ~ 65535

731
PLC Connection Guide

Note: The wiring diagrams above are drawn based on MT8100i structure, the actual
placement of pins may vary according to HMI module.

Driver Version:
Version Date Description
V1.00 Aug/24/2011 Driver released.

732
PLC Connection Guide

YASKAWA SMC 3010

Supported Series: YASKAWA SMC Series Servo Motor Controller.

HMI Setting:
Parameters Recommended Options Notes
PLC type YASKAWA SMC 3010
PLC I/F RS232
Baud rate 19200 9600, 19200
Data bits 8
Parity None
Stop bits 1

Device Address:
Bit/Word Device type Format Range Memo
B AF D 0~1
B BN D 0~1 Write only
B BP D 0~1 Write only
B BV D 0~1 Write only
B CB DDDD 0 ~ 9999 Write only
B CM D 0~1 Read only
B DV D 0~1
B EB D 0~1
B OE D 0~1
B RS D 0~1 Write only
B ST D 0~1 Write only
B TB Do 0 ~ 17 Read only
B V_Bit DDDdd 0 ~ 99931 *2
B D_arr_Bit DDDdd 0 ~ 99931
DW AC D 0~4
DW DC D 0~4
DW BL D 0~4
W CD D 0~2 Write only
W CE D 0~2

733
PLC Connection Guide
Bit/Word Device type Format Range Memo
DW DE D 0~4
DW DP D 0~4
W DT D 0~2
W EC D 0~2
DW EM D 0~4
W ER D 0~2
W FA D 0~2
DW FL D 0~4
W FV D 0~2
DW GR D 0~4
DW JG D 0~4
DW MM D 0~4
W MT D 0~2
W NA D 0~2
W OP D 0~2
DW PA D 0~4 Write only
DW PR D 0~4
DW SP D 0~4
W TC D 0~2 Read only
W TM D 0~2
W TW D 0~2
DW VA D 0~4
DW VD D 0~4
DW VS D 0~4
DW IL D 0~4
DW IT D 0~4
DW KD D 0~4
DW KI D 0~4
DW KP D 0~4
DW OF D 0~4
DW TL D 0~4
DW VR D 0~4
DW VT D 0~4
DW PF D 0~4 *1
DW VF D 0~4
734
PLC Connection Guide
Bit/Word Device type Format Range Memo
DW V DDD 0 ~ 999 *2
F F DDD 0 ~ 999 *2
W D_array DDD 0 ~ 999
W R_array DDD 0 ~ 999

Note:
*1 PF is the communication parameter of SMC_3010, the default is 10.4, if the value is not 10.4, all values
will be displayed incorrectly.
*2 User defined integer variable V000~V999, floating point variable F000~F999.

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS232 9P COM3 RS232 9P SMC3010 CN6 RS232
D-Sub Female D-Sub Female 9P D-Sub Male
2 RX 8 RX 2 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P SMC3010 CN6 RS232
D-Sub Female D-Sub Female D-Sub Male 9P D-Sub Male
2 RX 6 RX 8 RX 2 TXD
3 TX 4 TX 7 TX 3 RXD
5 GND 5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

735
PLC Connection Guide
MT6050i/MT8050i
COM1 RS232 9P SMC3010 CN6 RS232
D-Sub Female 9P D-Sub Male
9 RX 2 TXD
6 TX 3 RXD
5 GND 5 GND
7 RTS
circuit
8 CTS

Driver Version:
Version Date Description
V1.30 Mar/29/2010

736
PLC Connection Guide

YASKAWA SMC 3010 (Ethernet)

Supported Series: YASKAWA SMC Series Servo Motor Controller.

HMI Setting:
Parameters Recommended Options Notes
PLC type YASKAWA SMC 3010 (Ethernet)
PLC I/F Ethernet
Port no. 23

737
PLC Connection Guide
Bit/Word Device type Format Range Memo
DW EM D 0~4
W ER D 0~2
W FA D 0~2
DW FL D 0~4
W FV D 0~2
DW GR D 0~4
DW JG D 0~4
DW MM D 0~4
W MT D 0~2
W NA D 0~2
W OP D 0~2
DW PA D 0~4 Write only
DW PR D 0~4
DW SP D 0~4
W TC D 0~2 Read only
W TM D 0~2
W TW D 0~2
DW VA D 0~4
DW VD D 0~4
DW VS D 0~4
DW IL D 0~4
DW IT D 0~4
DW KD D 0~4
DW KI D 0~4
DW KP D 0~4
DW OF D 0~4
DW TL D 0~4
DW VR D 0~4
DW VT D 0~4
DW PF D 0~4 *1
DW VF D 0~4
DW V DDD 0 ~ 999 *2
W F DDD 0 ~ 999 *2
W D_array DDD 0 ~ 999
W R_array DDD 0 ~ 999

738
PLC Connection Guide

Note:
*1 PF is the communication parameter of SMC_3010, the default is 10.4, if the value is not
10.4, all values will be displayed incorrectly.
*2 User defined integer variable V000~V999, floating point variable F000~F999.

Driver Version:
Version Date Description
V1.10 Mar/29/2010

739
PLC Connection Guide

YOKOGAWA FA-M3
Supported Series : FA-M3 CPU SP35-5N, SP55-5N CPU port, F3LC11 Computer Link
module.

Website : http://www.yokogawa.com/itc/itc-index-en.htm

HMI Setting:
Parameters Recommended Options Notes
PLC type YOKOGAWA FA-M3
PLC I/F RS232
Baud rate 19200 9600, 19200
Data bits 8 8
Parity Even Even, Odd, None
Stop bits 1 1
PLC sta. no. 1 1-31

PLC Setting:
Use Personal Communication Link
Communication mode Use checksum
Use End Character

WideField communication setting:

For WideField communication setting, select [Tool]/ [Set Environment], the default is
[Automatic]. Using the Automatic Recognition, WideField software will connect the current
PLC and get the PLC communication setting. If the PLC communication configuration is
already known, select the [Fixed] mode, It will connect with the PLC quickly.

740
PLC Connection Guide

P.S Since Personal Computer link is used, when connecting to PLC it will delay about
20sec for testing communication.

YOKOGAWA PLC Communcation Setting:

YOKOGAWA FA-M3
CPU SP55-5N (same SP35-5N)
[File] /[New Project] to create a new project.

741
PLC Connection Guide
Click [Configuration] to set up communication.

Device Address:
Bit/Word Device type Format Range Memo
B X DDDDD 0 ~ 71664
B Y DDDDD 0 ~ 71664
B I DDDDD 1 ~ 16384
B M DDDD 1 ~ 9984
B L DDDDD 0 ~ 78192
W D DDDDD 1 ~ 16384
W B DDDDD 1 ~ 32768
W V DDD 1 ~ 256
W W DDDDD 1 ~ 71024
W Z DDDD 1 ~ 1024

742
PLC Connection Guide

Wiring Diagram:
The following represents the cable end connector.
9P D-Sub to 9P D-Sub: Cable KM11
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 2 TXD
3 TX 7 TX 3 RXD
5 GND 5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 2 TXD
3 TX 4 TX 7 TX 3 RXD
5 GND 5 GND 5 GND 5 GND

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 2 TXD
6 TX 3 RXD
5 GND 5 GND

743
PLC Connection Guide
The following represents the cable end connector.
9P D-Sub to 9P D-Sub: LC11
eMT3000 series
COM1 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female
2 RX 8 RX 3 TXD
3 TX 7 TX 2 RXD
5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

MT6000/8000 series except MT6050i/MT8050i

COM1 RS232 9P COM2 RS232 9P COM3 RS232 9P RS232 9P D-Sub Male
D-Sub Female D-Sub Female D-Sub Male
2 RX 6 RX 8 RX 3 TXD
3 TX 4 TX 7 TX 2 RXD
5 GND 5 GND 5 GND 5 GND
7 RTS
circuit
8 CTS

MT6050i/MT8050i
COM1 RS232 9P RS232 9P D-Sub Male
D-Sub Female
9 RX 3 TXD
6 TX 2 RXD
5 GND 5 GND
7 RTS
circuit
8 CTS

744
PLC Connection Guide

Driver Version:
Version Date Description
V1.20 Oct/23/2009
V1.30 May/31/2012 Extended address L range up to 78192.

745
PLC Connection Guide

YOKOGAWA FA-M3 (Ethernet)

Supported Series : FA-M3 CPU SP35-5N, SP55-5N with F3LE01-5T/F3LE11-0T Ethernet
module.
Website: http://www.yokogawa.com/itc/itc-index-en.htm

HMI Setting:
Parameters Recommended Options Notes
PLC type YOKOGAWA FA-M3 (Ethernet)
PLC I/F Ethernet
Port no. 12289
PLC sta. no. 1

PLC Setting:
Communication mode Set IP Address, and set all condition setup switch to OFF.

Device Address:
Bit/Word Device type Format Range Memo
B X DDDDD 0 ~ 71664
B Y DDDDD 0 ~ 71664
B I DDDDD 1 ~ 16384
B M DDDD 1 ~ 9984
B L DDDDD 0 ~ 78192
W D DDDD 1 ~ 8192
W B DDDDD 1 ~ 32768
W V DD 1 ~ 64
W W DDDDD 1 ~ 71024
W Z DDD 1 ~ 512

746
PLC Connection Guide

Driver Version:
Version Date Description
V1.00 Dec/30/2008 Driver released.
V1.10 May/31/2012 Extended address L range up to 78192.

747
PLC Connection Guide

YUDIAN AIBUS
Supported Series: UDIAN Automation AI-501, AI-518, AI-519, AI-701, AI-702M, AI-704M,
AI-706M, AI-719.

Website: http://www.yudian.us

HMI Setting:
Parameters Recommended Options Notes
PLC type AIBUS
PLC I/F RS485 2W RS232
Baud rate 9600 9600, 19200
Data bits 8
Parity None
Stop bits 2
HMI sta. no. 0
PLC sta. no. 1 0-100

On-line simulation YES

Extend address mode NO

Device Address:
AI-518

Bit/Word Device type Format Range Memo

W 0 00H DD SV/STEP
W 1 01H DD -1999 ~ 9999 HIAL
W 2 02H DD -1999 ~ 9999 LoAL
W 3 03H DD 0 ~ 9999 dHAL
W 4 04H DD 0 ~ 9999 dLAL
W 5 05H DD 0 ~ 2000 dF
W 6 06H DD 0~4 CtrL
W 7 07H DD 0 ~ 9999 M5
W 8 08H DD 1 ~ 9999 P
W 9 09H DD 0 ~ 2000 t

748
PLC Connection Guide

Bit/Word Device type Format Range Memo

W 10 0AH DD 0 ~ 125 CtI
W 11 0BH DD 0 ~ 37 Sn (read only)
W 12 0CH DD 0~3 dIP (read only)
W 13 0DH DD -1999 ~ 9999 dIL
W 14 0EH DD -1999 ~ 9999 dIH
W 15 0FH DD 0 ~ 9999 ALP
-1999 ~ 4000
W 16 10H DD Sc
0.1℃
W 17 11H DD 0 ~ 48 Op1
W 18 12H DD -110 ~ 110% oPL
W 19 13H DD 0 ~ 110% oPH
W 20 14H DD 0 ~ 127 CF (read only)
Baud rate（bAud）
/808Pstatus word:
W 21 15H DD 0 ~ 19.2K
run: 0 suspend: 4 stop: 12
(read only)
W 22 16H DD 0 ~ 100 ADDR
W 23 17H DD 0 ~ 20 dL
W 24 18H DD 0 ~ 127 Run
W 25 19H DD 0 ~ 9999 Loc

AI-701
Bit/Word Device type Format Range Memo
W 1 01H DD -9990 ~ 30000 HIAL
W 2 02H DD -9990 ~ 30000 LoAL
W 3 03H DD -9990 ~ 30000 HdAL
W 4 04H DD -9990 ~ 30000 LdAL
W 5 05H DD 0 ~ 2000 AHYS
W 11 0BH DD 0 ~ 37 InP (read only)
W 12 0CH DD 0~3 dPt
W 13 0DH DD -9999 ~ 30000 SCL
W 14 0EH DD -9999 ~ 30000 SCH
W 15 0FH DD 0 ~ 4444 AOP
-1999 ~ 4000
W 16 10H DD Scb
0.1℃

749
PLC Connection Guide
Bit/Word Device type Format Range Memo
W 17 11H DD 0 ~ 48 Opt
Baud rate（bAud）
/808P status word
W 21 15H DD 0 ~ 19.2K
run: 0 suspend: 4 stop: 12
(read only)
W 22 16H DD 0 ~ 80 ADDR
W 23 17H DD 0 ~ 40 FILt
W 25 19H DD 0 ~ 255 Loc

Wiring Diagram:
The following represents the cable end connector.
eMT3000 series
COM1 RS485 2W COM3 RS485 2W RS485 2W terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 4 COMM A
2 RX+ 9 Data+ 3 COMM B
5 GND 5 GND

MT6000/8000 series except MT6050i/MT8050i

COM1 RS485 2W COM3 RS485 2W RS485 2W terminal
9P D-Sub Male 9P D-Sub Male
1 RX- 6 Data- 4 COMM A
2 RX+ 9 Data+ 3 COMM B
5 GND 5 GND

750
PLC Connection Guide
MT6050i/MT8050i
COM1 RS485 2W COM3 RS485 2W RS485 2W terminal
9P D-Sub Female 9P D-Sub Female
1 RX- 7 Data- 4 COMM A
2 RX+ 8 Data+ 3 COMM B
5 GND 5 GND

Driver Version:
Version Date Description
V1.20 Dec/30/2008

751
PLC Connection Guide

MT6050i/MT8050i Com Port Pin Assignment

C O M C P U P W R

Bottom View

Front View
MT6050i/MT8050i
Pin assignment of the 9 Pin, Male,
Pin assignment of the 9 Pin, Male, SUB-D, COM1 [RS-232]/ [RS-485], COM3 [RS-485] Port. Only
Com1[RS485 2W] support MPI 187.5K.
Pin# Symbol Com1[RS485] Com1[RS232] Com3[RS485]
4 wire R e s e t
D I P S W
2 wire
Cutout dimensions:
1 Rx- Rx- Data- MT-6050i:
119mm [4.685"] W x 93mm [3.661"] H
2 Rx+ Rx+ Data+
3 Tx-
+ --
--
Tx- C O M

4 Tx+ Tx+
Rear View
5 GND GND
6 TxD Transmit
7 Data- Data-
8 Data+ Data+
9 RxD Receive

752
PLC Connection Guide

Wiring Diagram:
MT6050i COM1 [RS-232] PLC RS-232
9P D-SUB Female Communication Com Port interface
9 RXD TXD
6 TXD RXD
5 GND GND

MT6050i COM1 [RS-485 2w] PLC RS-485 2w

9P D-SUB Female Communication Com Port interface
1 Data- Data-
2 Data+ Data+

MT6050i COM3* [RS-485 2w] PLC RS-485 2w

9P D-SUB Female Communication Com Port interface
7 Data- Data-
8 Data+ Data+
*RS485 2W COM3 is only available for MT6050iv2

MT6050i COM1 [RS-485 4w] PLC RS-485 2w

9P D-SUB Female Communication Com Port interface
1 RX- TX-
2 RX TX+
3 TX- RX-
4 TX+ RX+

753

Руководство По Подключению к ПЛК Англ Язык
No ratings yet
Руководство По Подключению к ПЛК Англ Язык
801 pages
PLC Connection Guide1
No ratings yet
PLC Connection Guide1
1,044 pages
PLC Connection Guide
No ratings yet
PLC Connection Guide
1,163 pages
PLC Connection Guide 4
No ratings yet
PLC Connection Guide 4
1,119 pages
PLC Connection Guide
100% (2)
PLC Connection Guide
520 pages
PLC Connection Guide (Unlockplc - Com)
90% (10)
PLC Connection Guide (Unlockplc - Com)
1,163 pages
PLC Connection Guide
No ratings yet
PLC Connection Guide
436 pages
PLC Connection Guide Weintek (Hmivietnam - Com) PDF
No ratings yet
PLC Connection Guide Weintek (Hmivietnam - Com) PDF
1,128 pages
PLC Connection Guide
No ratings yet
PLC Connection Guide
1,158 pages
PLC Connection Guide
100% (1)
PLC Connection Guide
1,142 pages
PLC Connection Guide Weintek
100% (3)
PLC Connection Guide Weintek
1,370 pages
PLC Connection Guide PDF
No ratings yet
PLC Connection Guide PDF
1,508 pages
PLC Connection Manual
No ratings yet
PLC Connection Manual
317 pages
Conect Diagram
No ratings yet
Conect Diagram
336 pages
DELTA Dop W en 20100809
No ratings yet
DELTA Dop W en 20100809
232 pages
CAS CI-1580A: HMI Setting
No ratings yet
CAS CI-1580A: HMI Setting
6 pages
Dop W Eng 20110516
No ratings yet
Dop W Eng 20110516
234 pages
HMI Delta Connection Manual
No ratings yet
HMI Delta Connection Manual
234 pages
EMERSON Charge Module: HMI Setting
No ratings yet
EMERSON Charge Module: HMI Setting
3 pages
Schneider_MODBUS_RTU
No ratings yet
Schneider_MODBUS_RTU
4 pages
Vigor
No ratings yet
Vigor
5 pages
MODBUS RTU 0x 1x Range Adjustable
No ratings yet
MODBUS RTU 0x 1x Range Adjustable
13 pages
Motrona CT 150
No ratings yet
Motrona CT 150
3 pages
Device 3 Connection Guide
No ratings yet
Device 3 Connection Guide
9 pages
Koyo Direct
No ratings yet
Koyo Direct
22 pages
MODBUS_Server_COM_Ethernet
No ratings yet
MODBUS_Server_COM_Ethernet
12 pages
HMI Connecting Guide PDF
No ratings yet
HMI Connecting Guide PDF
382 pages
XINJE XC Series: HMI Setting
No ratings yet
XINJE XC Series: HMI Setting
3 pages
P5_HMI_ConnectionManual_en_v1-0-2
No ratings yet
P5_HMI_ConnectionManual_en_v1-0-2
286 pages
HMI Connection Manual_en
No ratings yet
HMI Connection Manual_en
385 pages
HMI and PLC Connecting Guide
No ratings yet
HMI and PLC Connecting Guide
392 pages
Kinco HMI and PLC Connecting Guide en 1506
No ratings yet
Kinco HMI and PLC Connecting Guide en 1506
403 pages
Kinco HMI and PLC Connecting Guide en 1506
100% (1)
Kinco HMI and PLC Connecting Guide en 1506
403 pages
DL-BCM Server: HMI Setting
No ratings yet
DL-BCM Server: HMI Setting
6 pages
Modbus Rtu PDF
No ratings yet
Modbus Rtu PDF
10 pages
Mitsubishi FX2N: HMI Setting
No ratings yet
Mitsubishi FX2N: HMI Setting
4 pages
EdgeLink Driver List 2
No ratings yet
EdgeLink Driver List 2
11 pages
GE RX3i
No ratings yet
GE RX3i
6 pages
HMI and PLC Connecting Guide Dtool 20200330
No ratings yet
HMI and PLC Connecting Guide Dtool 20200330
507 pages
Fuji NB Series: HMI Setting
No ratings yet
Fuji NB Series: HMI Setting
3 pages
Delta DVP: HMI Setting
No ratings yet
Delta DVP: HMI Setting
6 pages
Schneider MODBUS TCP IP
No ratings yet
Schneider MODBUS TCP IP
2 pages
Fatek Fb/Fbs/B1/B1Z Series: Hmi Setting
No ratings yet
Fatek Fb/Fbs/B1/B1Z Series: Hmi Setting
12 pages
MODBUS RTU (Adjustable) : HMI Setting
No ratings yet
MODBUS RTU (Adjustable) : HMI Setting
11 pages
HMI and PLC Connecting Guide PDF
No ratings yet
HMI and PLC Connecting Guide PDF
427 pages
MODBUS RTU Zero Based Addressing
No ratings yet
MODBUS RTU Zero Based Addressing
9 pages
Panasonic FP KW
No ratings yet
Panasonic FP KW
15 pages
Artrich Inverter AR100 Series
No ratings yet
Artrich Inverter AR100 Series
4 pages
Mitsubishi QJ71E71 Ethernet
No ratings yet
Mitsubishi QJ71E71 Ethernet
7 pages
Rockwell DH485
No ratings yet
Rockwell DH485
9 pages
Mitsubishi QJ71E71 (Ethernet) : HMI Setting
No ratings yet
Mitsubishi QJ71E71 (Ethernet) : HMI Setting
7 pages
Mitsubishi QJ71E71 Ethernet
No ratings yet
Mitsubishi QJ71E71 Ethernet
7 pages
HMI and PLC Connecting Guide
100% (3)
HMI and PLC Connecting Guide
384 pages
Coolmay Catalog
No ratings yet
Coolmay Catalog
16 pages