Scribd
Upload
433 views2 pages

BS1400 HTB1

1. The document describes the material properties of high tensile brass BS 1400 HTB1, which conforms to British and European standards for a copper-zinc alloy containing manganese, aluminum, and iron. 2. It is commonly used for commercial plumbing fittings and water valves due to its high tensile strength. 3. The document provides information on the alloy's chemical composition, fabrication properties, physical properties, melting points, density, electrical and thermal conductivity, coefficient of thermal expansion, modulus of elasticity, and magnetic permeability.

Uploaded by

Atul Kulkarni
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
433 views2 pages

BS1400 HTB1

1. The document describes the material properties of high tensile brass BS 1400 HTB1, which conforms to British and European standards for a copper-zinc alloy containing manganese, aluminum, and iron. 2. It is commonly used for commercial plumbing fittings and water valves due to its high tensile strength. 3. The document provides information on the alloy's chemical composition, fabrication properties, physical properties, melting points, density, electrical and thermal conductivity, coefficient of thermal expansion, modulus of elasticity, and magnetic permeability.

Uploaded by

Atul Kulkarni
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

HIGH TENSILE BRASS BS: 1400 HTB1

A high tensile strength brass conforming to BS 1400 HTB1


CuZn35AlFeMn and BS EN 1982-2008 CC765S
CuZn35Mn2Al1Fe1-C. It is generally used for commercial
plumbing fittings and other fairly standard water type valves.
Copper Alloys specializes in producing large-section forgings in
this alloy.

C52480 Phosphorus Bronze


:: Send Enquiry

Equivalent Specifications:

Specifications BS EN IS JIS DIN ISO Russian

Designation HTB1 CC765S - - 2.034 CuZn35Mn2AlFe1-C -

Chemical Composition:

Cu Pb Sn Zn Si Ni Fe Al Mn Other
Min 55 - - - - - 0.7 0.5 0.1 -
Max Rem. 0.5 1 Rem. 0.1 1.0 2.0 2.5 3.0 0.2

Fabrication Properties:

Joining Technique Suitability


Soldering Fair
Brazing Fair
Oxyacetylene Welding Poor
Gas Shielded Arc Welding Poor
Coated Metal Arc Welding Poor
Machinability Rating 26
Physical Properties:

Melting Point – Liquidus °F 1616


Melting Point – Solidus °F 1583
Density lb/cu in. at 68°F 0.301
Specific Gravity 8.33
Electrical Conductivity% IACS at 68°F 22
Thermal Conductivity Btu/ sq ft/ ft hr/ °F at 68°F 49.6
Coefficient of Thermal Expansion 68-21210⁻⁶ per °F (68 – 212°F) 11.3
Specific Heat Capacity Btu/ lb /°F at 68°F 0.09
Modulus of Elasticity in Tension ksi 15000
Magnetic Permeability* 1.09

Sizes Available:

TUBES 6.35 mm to 110mm


ROUND WIRES 1 mm to 11mm
ROUND RODS 1.2 to 250 mm
HEX RODS Min. 5 mm to Max. 60 mm
SQUARE RODS Min. 4 mm to Max. 60 mm
FLATS Min. 4 mm thickness and max width of 120mm
PROFILES As per customer drawings
HOLLOW RODS Min Bore Size 20mm and Max OD 130mm

You might also like