\ API-S70 - Practice Exam #3 ‘Open Book V1. The most important items to be included in progressive records for a piping system \ \ are the date of installation, material used, original thickness measurements, and which of the following? a) Name of the individual determining the minimum design metal thickness b) Names of the original fabricators and nondestructive examination inspection records from the construction of the system ¢) Names of the original design organization and the material suppliers d) Location and dates of subsequent inspections and calculated retirement thickness 2. Welders may be qualified by radiographic examination of groove welds, with the exception of: a) SAW with silicone-based flux b) GMAW globular transfer ©) GMAW pulsed-are 3. A buried pipe designed for 100psi service is tested is tested at 125psig for cight hours. After four hours, the pressure dropped Spsig, and the system is pumped back up to 125psig. During the remaining four hours of the test, the pressure drops Spsig, According to instructions in API-570, the inspector should: b) Evacuate the pipe and conduct an external visual inspection c) Reject the test and conduct further inspection d) Visually inspect the pipe and find the leak 4, A 16-inch piping circuit originally 0.500 inch thick has a corrosion rate of 0.025 inch per year and a MAWP of 500psi. If the circuit’s current thickness is 0.375 inch, how thick will it be at the next planned inspection in 3.5 years? (Assume E ~ 1.0 and $ = 20,000psi) a a) 0.0875 inch yh b) 0.200 inch Sinch d) 0.350 inch 5. Re-heating of a hardened metal to a temperature below the transformation range to improve toughness is known as: i Stress relieving c) Annealing d) Normalizing BAY Technical Associates, Inc. 1API-570 - Practice Exam #3 Open Book \ 6. What is the maximum permissible height of weld reinforcement for a girth weld in service condition piping having a wall thickness of 3/8 inch? 2) sie ©) 5/32 inch 4) 3/16 inch \ 7. During the hydrostatic testing of 300 series stainless steel piping using potable water, the maximum chloride content should be nh b) 500 parts per million arty fe “iy! ©) 250 parts per billion eH v \ @) 500 parts per billion 8 \4 . Hydrogen cracking in carbon steel is commonly encountered when using: a) SMAW, GTAW, and SAW welding processes \¢, 9° b) SMAW, GMAW, and SA’ jing processes \ d) SMAW, FCAW, and GTAW welding processes 9 During fabrication, radiography reveals slag inclusion, undereut, and incomplete penetration (IP) in a butt weld joining two pieces of NPS 14 pipe. The pipe is 3/8 inch thick at the weld, and the three areas of IP are 0.06 inch, 0.03 inch, and 0,02 inch long, respectively. The maximum depth of IP is 1/32 inch. The one piece of slag is 1/4 inch long and 1/8 inch wide. The undercut is 1/32 inch deep. For normal fluid service, the weld is: a) Unacceptable due to the length of incomplete penetration b) Unacceptable due to undercut \ d) Unacee lag inclusion 10. Fora pipe exceeding 10” diameter, atest point is an area defined by a circle having a diameter no greater than: a) 1 inch b) 2 inches ¢) 2.5 inches d) inches — BAY Technical Associates, Inc. 2API-S70 - Practice Exam #3 Open Book \ 11. A welder has welded a 5/8-inch thick flat plate groove weld test coupon in the 3G position, Which bend test and how many of each type is required to qualify this welder? a) One side bend test b)_ Two face bend tests and one root bend test, or two side bend tests \ 4) One face bend test and two root bend tests 12. When performing liquid penetrant examination of nickel base alloys, austenitic stainless steels, and titanium, which of the following is correct for verifying acceptable penetrant materials? a) Obtain the certifications of contaminant content for liquid penetrant materials b) Obtain copies of identification and batch numbers from material containers \ ©) Obtain the certifications of penetrant and developer materials for sulfur content d) Obtain the certification of cleaner material for moisture content 13. A piping system has the following characteristics: Design pressure/temperature TO0psil/300°F Pipe deseri NPS 10, A-106 Gr. B Outside diameter of pipe “D” 10.75 inches Allowable stress “S” 20000psi Longitudinal weld efficiency “E” 10 Thickness determined by inspection 0.30 inch Observed corrosion rate: 0.02 inch per year Next planned inspection 5 years Given this data, what is the maximum allowable working pressure for this system? b) 744psi ©) 967psi d) 1050psi 14, Of the following, which is the height of the raised face of a Class 400 flange? a) 0.06 inch b) 0.100 inch ©) 0.125 inch —— d) 0.250 inch BAY Technical Associates, IncAPI-570 - Practice Exam #3 Open Book 15, A scamless NPS 10 (10 % inch OD) pipe of ASTM A-106 Gr. B material operates at a maximum of 750psi and 700°F. Considering only pressure design thickness for straight pipe, what minimum thickness is required? a) 0.195 inch \ 16. A comprehensive picture of the general condition of any pi determined by: 1g system can be a) API inspection guideline b) Complete and accurate inspection records: ¢) Original design drawings and isometries \ 4) Field thickness measurement location (TML) readings 17 Flanged joints and flanged fittings may be subjected to a system hydrostatic test at a pressure that is: a) 1.25 times the 100°F rating rounded down to the next lower 25psi. b) 1.25 times the 100°F rating rounded up to the next higher 2Spsi ©) 1,5 times the 100°F rating rounded down to the next lower 25psi d) 1.5 times the 100°F rating rounded up to the next higher 25psi. \ 18, What type of insulation is recommended for 300 Series stainless steel to minimize the risk of pitting and chloride stress corrosion cracking (SSC)? a) Asbestos b) Cellulose based with water resistant binder ©) High chloride base (greater than 250PPM) d) Low chloride \ 19, When performing weld repairs, the preheat temperature shall be in accordance with the code requirements except in which case? a) Adding a support attachment plate b) Temporary repairs, with the approval of the inspector ¢) Temporary repairs, with the approval of the piping engineer d) Adding a non-pressure bearing attachment plate BAY Technical Associates, Inc 4API-570 - Practice Exam #3 ‘Open Book \y What is the recommended maximum inspection interval for thickness measurements of an off-site gasoline piping system? a) lyear b) 3 years ©) 5S years d) 10 years A piping system made of mixed grades of piping including A-S3 carbon steel with silicon killed elbows and fittings has recently been re-rated from 400°F to 450°F. The process fluid contains 0.52% weight sulfur. The unit inspector should: ao b) Continue monitoring the system utilizing existing TMLs if they have pe ‘more than 0,002 inch per year corrosion rates ©) Relocate the TMLs to the fittings 4) Not be concerned with the 50°F change ‘What is the maximum Brinell hardness number (BHN) allowed when welding pipe using P-6 material? a) BHN 200 b) BHN 225 -¢) BHN241 \ 4) Hames testing is not required for this material 23. A final closure weld in a modified piping system consists of a full penetration butt weld between two sections of pipe that have been miter cut. ‘The closure weld is acceptable only if: a) 100% radiographic examination is performed b) The root and surface passes are fully examined using the magnetic particle method ©) Ultrasonically tested with an ee beam 24, What is the nominal thickness of a permanent blank made of A-36 material for a flange connection with a design pressure of 300psi at 650°F, with a 0.125 inch corrosion allowance, and a gasket inside diameter of 12.5 inches? a) 0.625 inch b) 0.750 inch ~¢) 0.846 inch 4) 1.000 inch Ww BAY Technical Associates, Inc. 5API-570 - Practice Exam #3 Open Book \ 25. What is the maximum pressure rating for a Class 400 flange that has ¢ maximum design temperature of 850°F? (The flange material is A-182 Gr. F316) 26. What is the minimum required thickness (including corrosion allowance) for a 4-inch standard pipe system (4.5-inch OD) if it operates at 52Spsi at 400°F? The pipe material is API-SL A25 ERW and the corrosion allowance is 1/16”. a) 0.0989 inch b) 0.1468 inch \ ©) 0.1589 inch ~ d) 0.1614 inch 27. The gage used to monitor the pressure during a sensitive leak test shall have a pressure range of at least 2) 0.5 times the test pressure, but no higher than two times the test pressure —- ¢) 2 times the test pressure, but no higher than four times the test pressure 4) 2 times the test pressure, but no higher than five times the test pressure ‘28. What is the total number of face and root bend tests required to qualify a welder on a 0.75-inch groove weld? a0 b) 2 ) 3 \ a4 29. Which of the following is not an acceptable temporary repair patch for an NPS 12 carbon-steel pipe with localized corrosion? a) Eight in circular patch b)_ Six inch by six inch square patch with comer radius of one inch ¢)_ Six inch circular patch 4) Six inch by six inch square patch with comer radius of two inches BAY Technical Associates, Inc. 6API-570 - Practice Exam #3 ‘Open Book \s0. Incomplete penetration when welding austenitic stainless steel is commonly \ encountered when welding using: a) SAW, FCAW, and GMAW welding processes only b) SMAW, FCAW, and GMAW welding processes only _¢) Any of the welding processes d) SMAW, GTAW, and GMAW welding processes only 31. When selecting low-strength bolting for a set of Class 300 flanges in a piping system designed for a maximum temperature of 460°F, which of the following ASTM specifications should not be used? a) ASTM A-193 Gr. B8C CL. —b) ASTMA307Gr. B ©) ASTM A-320 Gr. B8 CLI @) ASTM A-320 Gr. BST CL.1 32. A piping system constructed of A-106 Gr. B (A-234 Gr. WPB fittings) is designed for 325psi at 750°F, At what pressure should the system be tested if 70°F steam condensate is used as the test medium? a) 325psi b) 488psi ¢) 650psi ay 750psi 33. All of the following should be integral parts of safety procedures conceming pipe inspection except: a) Segregating piping ) Installing blinds ©) Leak testing -d) Locating TMLs 34, Magnetic Flux Leakage (MFL) examination can detect discontinuities on which of the following materials? a) Austenitic materials from one side om ©) Plastic reinforced fiberglass vessels 4) Non-metallic piping and piping lined with nonmetals BAY Technical Associates, Inc. 7API-570 - Practice Exam #3 Open Book '35. In a piping repair, the base metal is P-8 material and the pipe wall thickness is 1 % inches, What is the minimum hold time for heat treatment? a) 1 Hour is b) 1 Hour 15 minutes ¥ uy yey c) 2Hours mer pl yt t -d) None wt fi om 36. An NPS 8 pipe operates at a maximum of 67Spsi and 650°F. The pipe is A-106 Gr. B ‘material. What allowable stress should be used to determine the pipe’s minimum required thickness? a) 16500psi — by 17000psi ©) 17300psi 4) 20000psi \. 37. Caustic stress comosion cracking ean occur at low caustic levels ia concentrating mechanism is present. In such cases, caustic concentrations of $0_PPM to (0 PPM are sufficient to cause cracking, a) 10,20 _ b) 50,100 ) 100, 150 4) 150,200 38. Given the following in a carbon steel piping system constructed in accordance with ASME B31.3, what is the minimum required thickness? Design pressure 600psi Design temperature 650°F Diameter NPS 12 Schedule 40 Allowable stress | 19000psi Joint efficiency Ej ||, 1.0 Wo a) 0.187 inch fr b) 0.189 inch —e) 0.199 inch — 4) 0.217 inch BAY Technical Associates, Inc. 8API-S70 - Practice Exam #3 \ Open Book \ 39. When a locally thinned area (exceeding the corrosion allowance) is being evaluated for acceptability, the evaluation should be in accordance with the principles of: a) ASME Section VIII a ‘ ‘b) API Recommended Practice API-579» (0 tgasad_ptiwiarlom® c) ASME Section IX a ae d) ASME B31.3 40. Of the following, which is not a precaution to take when local post weld heat treatment (PWHT) is substituted for 360° banding? a) Overall and local strains and distortions of the piping wall shall be considered _) A piping engineer must determine is the PWHT is in accordance with ASME “Section VII | ©) A preheat of 300°F or higher is maintained while welding, as specified by the specific weld procedure d) The PWHT is performed for Code compliance and not for resistance to \ environmental cracking \v a1, the maximum depth of undercut permitted for a girth weld made in normal fluid service piping of 14" thickness is: a) No visible undercut db) 1/32 inch ) 1/16 inch \ d) 1/8 inch 42. A pipe must have what specified minimum yield strength (SMYS) before temporary localized repairs can be made? 2) 7000psi ~-b) $40000psi- ‘ c) >40000psi 4) <40000 kilopaseals 43. What are the total number of test coupons (tension and bend) that must be tested to qualify a4” groove weld procedure? a) 2 b) 4 ome a8 BAY Technical Associates, Inc.API-570 - Practice Exam #3 Open Book 4, In a piping system with a design pressure of SO0psi and a design temperature of 90°F, what is the minimum acceptable flange class if the flange material is A-182 Gr. F2? WS ae ie a) casing x pk c) Class 600 d) Class 900 45, What is the minimum thickness for an NPS 6 seamless pipe fabricated of A-106 Gr.B and used in a 400psi, 500°F process? °) d) 0.132 inch \ 46. The recommended upstream limit of the injection point circuit is a: 2) Minimum of 12 inches or 3 pipe diameters, whichever is less b) Maximum of 12 inches or 3 pipe diameters, whichever is greater ©) Maximum of 12 inches or 3 pipe diameters, whichever is less \ 4) Minimum of 12 inches or 3 pipe diameters, whichever is greater _ \ 47. A pipe without cathodic protection is buried in soil with a resistivity of 1500 ohm-em. ‘The maximum interval between external inspections is: a) 2.5 years Bb) Syears ©) 10 years d) 15 years 48. The yoke technique of Magnetic Particle testing shall only be used to detect what type of discontinuities? a) Slight sub-surface discontinuities b) Laminations \ @) Lack of penetration 49. A miter bend for severe cyclic service should have an angle of no more than Xie ays ys, b) 30.0° ue ©) 375° a 4s BAY Technical Associates, Inc. 10API-570 - Practice Exam #3 Open Book 50. A piece of NPS 12 A-106 Gr. B pipe is needed for a modification in a piping system designed for 500psi at 500°F with no corrosion allowance. To be sure the actual thickness of the pipe is sufficient, what is the minimum thickness that must be ordered to account for the 12 ¥% % mill under-tolerance? a) 0.159 inch b) 0.167 inch ©) 0.182 inch d) 0.188 inch For Questions 51 through 53, refer to the attached Welding Procedure \ Specification and Procedure Qualification Record ‘51. Regarding the joint shown, the Welding Procedure Specification: a) Includes all required information b) Should specify uphill or downhill progression ©) Must show the weld layers 4) Should address the joint angle \ so, Regarding the mechanical tests shown, the Procedure Qualification Record qualifications: a) Have not been met because one of the guided bend tests failed b) Have not been met because on tensile test failed €} Have not been met because face and root bends were not performed 53. Regarding the thickness range shown on the Welding Procedure Specification, a correct statement is that the: a) Upper limit could be cight inches b) Lower limit could be 1/16 inch c) Lower limit could be 1/8 inch _ d) Range is accurate as shown BAY Technical Associates, Inc. uAPI-570 - Practice Exam #3 Open Book ‘Welding Procedure Specification (WPS) Front Company Name BAY Tech By: _Chip Beaph C Welding Procedure Specification No” S21 Date _10/0303_~ Supporting PQR Now) ST] Revision No. 0 Date _—— Welding Process(es) _SMAW Type) Manual ~ ‘Automate, Manual, Machine, Semi-Auto) Joints (QW-402) Details Joint Design Single V Groove * Backing Ges) Ch wo) Deere Backing Material (Type): Weld : Cutan dee) DB Nonmetai ote are Sketches, Production Drawings, Weld Symbols or Wren Descipton should sow the general rangement of he ars tobe welded. Root spacing and wel roove tie ‘nay be spectid where applicable “The joint designs above ae typical for sroove weds, chesk the production drawing for weld joint design andra, *Base Metals (QW-403) PNo. 1 GroupNo, 1 ToP-No _ Group No or Specification type and grade ‘To Specification type and grade OR Chem, Analysis and Mech, Prop. To Chem, Analysis and Mech, Prop. Thickness Range: Base Metal: Groove: 1875 to ,8640 All Pipe Dia. Range: Groove: All All Other: * Filler Metals (QW-404), Root Balance Spee. No. (SFA) _5.1 ‘AWS No. (Class) EOI Root Balance FNo Fa 4 ANo. Al Al Size of Filler Metals _1/8 & 5732 Weld Metal Thickness Range: Groove 1875 10 8640 let 10 3/4 throat Electrode-Flux (Class) Flux Trade Name ‘Consumable Insert Other Bach base metal - filler metal combination should be recorded individually. BAY Technical Associates, In. 2[ Positions (QW=40s API-570 - Practice Exa Open Book mn #3 Welding Procedure Specification (WPS) (Back) ] Postweld Heat Treatment (QW-407) | Position(s) of Groove _All Temperature Range _None Welding Progression: “Up _®¥ Down XX Time Range _None Position of Fillet AIL Preheat (QW-406) Gas (QW-408) Percent Composition Preheat Temp. Min, _S0 Deg. F Gasles) __tMixtte) Flow Rate Interpass Temp. Max. 550 Deg, F Preheat Maintenance “None Shielding ‘Cominuows or special heating where apie sould be esarded} Trailing Wa Backin Wa Electrical Characteristics (QW-409) Current AC or DC _DC_ Polarity ‘Amps (Range) _90-220_ Volts (Range) (Amps and volts range should be recorded for each Blectrode size, position, and thickness, ele ‘This information may be listed in a tabular form Reverse “Tungsten Electrode Size and Type ‘are Tongs, 2 Thawed, ie) ‘Mode of Metal Transfer for GMAW (Siay a, son ceaing we ie) Electrode Wire feed speed range ‘Technique (QW-410) ‘String or Weave Bead Orifice or Gas Cup Size Initial and Tnterpass Cleaning (Brushing, Grinding, ete) ishing or grinding [Both sides oF weldjont | Method of Back Gouging Grinding Oscillation NA Contact Tube to Work Distance WA Multiple or Single Pass (per side) Multiple Multiple or Single Electrode Single Travel Speed (Range) Faris Peening None Other: — ~ Travel Other Weld | Process | Filler Metal Current Volt | Speed | (ee Remarks Comments ot ser Range | SF tin wc, Tork ‘All__[-SMAW_|_E-7018 |W" | DCRP | 90-160 |~ ‘All__| SMaW | _E-7018_| 5/32" | DcRP | 130-220 BAY Technical Associates, Inc. BAPI-S70 - Practice Exam #3 Open Book Procedure Qualification Report (PQR) (QW-200.2 of Section IX, ASME B & PV Code) Company Name BAY Tech Procedure Qualification Record Number Sai Date WPS Number _$21 Welding Process(es)___SMAW. "Type@)_ | Manual (Manual, Automatic, Semi-Auto) Toints (QW-403) 1 Coupon thighs 2330 Root ace: 3/32 Root spacing: VIG for combination qualifications. the deposited weld metal thickness shall be resol for each filler metal or process used) Base Metals (QW-403) Postweld Heat Treatment (QW-407) Material Specification SA-516 Temperature None Type or Grade Grade 70 Time No. 1 TP No. T Other ‘Thickness of Test Coupon 520 Diameter of Test Coupon Plate Gas (QW-408) Other Percent Composition Gas(es) Mixture Flow Rate Filler Metals (QW-404) Shielding “WA SFA Specification Ea ‘Trailing WA AWS Classification E7018 Backing “WA Filler Metal F-No. Fa Electrical Characteristics (QW-409) ‘Weld metal analysis A-No, A Current Size of Filler Metal 1" Polarity Other Amps Vos Deposited Weld Metal 5a ‘Tungsten Electrode Size Position (QW-405) Other Position of Groove Flat Technique (QW-410) Weld Progression (uphill, down Flat___| Travel Speed Other String or Weave Bead Preheat (QW-406) Oscillation Preheat Temp. 50 Deg. F Multiple or Single Pass (per side) Interpass Temp. 350 Deg: F Single or Multiple Electrodes Other Other BAY Technical Associates, Inc.API-570 - Practice Exam #3 Open Book (QW-483 (Back) Procedure Qualification Report (PQR) ‘Tensile Test (QW-150) Ultimate Unimate Type of Specimen Total Load Unit Stress failure & No. __Width | Thickness | Arca tb psi location 1 0.996 0350, 0.349 23250 (66,620__[ Base Metal 2 1.002 0350, 0351 24600 85 Base Metal Guided Bend Tests (QW-160) Type and Figure No. Results Side Bend, QW-462.2 No Defects Side Bend, QW-462.2 No Defects Side Bend, QW-462.2 1/8" defect in heat affected zone Side Bend, QW-462.2 No Defect Toughness Tests (QW-170) Specimen Noich, Noich |" Test_]_ Impact Lateral Exp Drop Weight ‘No. Location |" Type | Temp | Values | % Shear Mills | Break _[” No Break Results Satisfactory Macro - Results Type of Test Fillet Weld Tests (QW-180) Deposit Analysis Other Welder’s Name Yes _[]_ No _[]_ Penetration into Parent Metal: Yes O) No Other Tests Slim Picki Clock No. 99 Stamp No. sp. BAY Tech Laboratory Test No. 17e2 Tests conducted by We certify thatthe statements inthis record are correct and thatthe test welds were prepared, welded, and tested in accordance with the requirements of Section IX of the ASME Code, Date: 10/03/03 Manufacturer _BAY Tech Signature Cp Bae BAY Technical Associates, Inc.10. WL 12. 1B 14 15, 16. 7 18, 19, API-S70 Practice Exam #3 Answer Guide Open Book . d) Location and dates of subsequent inspections and calculated retirement thickness API-570 Paragraph 7.6 4) GMAW short-circuiting ASME Section IX QW-304 a) Accept the test as successful. API-S70 Paragraph 9.2.6 c) 0.2875 inch b) Tempering ASME B31.3 b) 1/8 inch API-570 Paragraph 8.2 => B31.3 Table 3413.2 ) 250 parts per million => API-S70 Paragraph 5.7 and Note c) SMAW, FCAW, and SAW welding processes Reference: API-577 Table 6 ©) Acceptable > B31.3 Table 341.3.2 d) 3 inches = API-570 Paragraph 3.46 ©) Two side bend tests => Section IX QW-452.1(a) a) Obtain the certifications of contaminant content for liquid penetrant materials content. ASME Section V T-641 a) 372psi => t = 0.30 - (5)(.02)(2) = 0.10 API-570 Paragraph 7.2 4) 0.250 inch => B16.5 Paragraph 6.4.1 PD 062 aoe a te ee 2(SE+PY) 33600 b) Complete and accurate inspection records => API-574 Paragraph 12.1 b) 0.240 inch = API-570 7.3 => ¢= = 23995" 4) 1.5 times the 100°F rating rounded up to the next higher 25psi. => B16.5 => 2.6 4d) Low chloride Reference: API-571 Paragraph 4.3.3.7(4) ©) Temporary repairs, with the approval of the piping engineer => API-570 8.2.2.1 BAY Technical Associates, Ine.API-570 Practice Exam #3 Answer Guide Open Book 20.) $ years => API-570—6.2.1 & Table 6-1 21. a) Increase the number of thickness measurement locations (TMLs) on the system => API-S70 Paragraph $.3.5(f) 22.) BHN 241 = B31.3 Table 331.1.1 23. d) A pressure test is applied to the entire system => API-570 Paragraph 8.2.6 [ae (83800) 155 4, eee ee = 51 Tere 900 24.¢) 0.846 inch = B31.3 = 304.5,3 fa = 25.) SS5psig => B16.5 Table F-2-2.2 26.4) 0.1614 inch => API-570 => 7.3 and B31.3 => 304.1 2(a)r = ———_©25)(4.5)_ : " 2[(03800)(.85) + (525\.4)] 27.b) 1.5 times the test pressure, but no higher than four times the test pressure => Section V Article 10 Paragraph T 1031 0625 28.a) 0 => ASME Section IX QW-452.1(2) (2 side bends are required) 29. a) Eight in circular patch => API-570 Appendix C Figure C-2 30.) Any of the welding processes Reference: API-S77 Table 6 31.b) ASTM A-307 Gr. B => BI6.5 Table 1B Note 12 (1.5325)(20000) 32. d) 750psi = B31.3 = 345.4.2 (Stress values are same for both materials, aba 33. d) Locating TMLs => API-570 => 5.2 (leak test may be part of the inspection) 34. b) Coated and uncoated ferromagnetic materials from one side Reference: Section V, Article 16, T-1610 35.) None => B31.3 Table 331.1.1 36.b) 17000psi => B31.3 Table A-I 37. b) 50, 100 Reference: API-S71 Paragraph 4.5.3.3(c) 38.¢) 0.199 inch => B31.3 Paragraph 304.1.2(a) (600)012.75) 2[(19000)(1) + (600)(.4)] BAY Technical Associates, Ine 239. 40. 4. 42. 43. 4, 45. 46. 47. 48. 49. 50. 51. 52. API-570 Practice Exam #3 Answer Guide Open Book b) API Recommended Practice API-579 = API-570 Paragraph 7.4 b) A piping engineer must determine is the PWHT is in accordance with ASME, Section VIII = API-570 => 8.2.2.2 b) 1/32 inch = B31.3 Table 341.3.2 b) <40000psi => API-570 Paragraph 8.1.3.1 ¢) 6 => ASME Section IX = QW-451.1 b) Class 400 = B16.5 Table F- 2-1.7 b) 0.070 inch => B31.3 => 304.1.2 @) Minimum of 12 inches or 3 pipe diameters, whichever is greater => API-570 => 5.3.1 b) 5 years => API-S70 Paragraph 9.2.6 and Table 9-1 ©) REF: Section V, Article T-755.1 a) 22.5° => B31.3 Paragraph 306.3.3 ($000275) t ~ 4) .188inch => B31.3 => 304.1.2 21089000) + 600(4)] (1.125)(.167)=.188" a) Includes all required information => Section IX => QW-253 & QW-402 c) Have all be met => Section IX QW-153(d) & QW-163 d) Range is accurate as shown => Section IX QW-451.1 BAY Technical Associates, In.