Type Series Booklet

1798.56/3-10 Movitec
High-pressure In-line Pumps
60 Hz

Movitec VE Movitec V Movitec LHS

Fields of Application Designation

Movitec VE are employed for general water supply, sprinkling, ir- Movitec V E S F 4 - 3
rigation and pressure boosting duties, for warm water and cooling Type-series
water recirculation. They are installed in domestic water supply Movitec V
systems, washing plants, water treatment and fire-fighting sys- Movitec VE (close-coupled design)
tems. Material variant
Movitec V(S) and LHS are employed for general water supply, Flange variant
sprinkling, irrigation and pressure boosting duties, for warm water, Pump size
hot water and cooling water recirculation, and condensate trans- Number of stages
port. They are installed in boiler feed circuits, domestic water sup-
ply systems, washing plants, water treatment and filter systems. Movitec LHS 6 - 10
They are used for degreaser baths/alkaline cleaning baths, alka- Type-series
lines and oils/emulsions, as well as for fire-fighting, reverse osmo- Pump size
sis and surface treatment applications. Number of stages
Material variants: blank or S, see page 3
Design Flange variants/connections: blank = oval flange
Multi-stage, vertical (horizontal installation see page 5) high-pres- F = round flange
sure centrifugal pumps, with suction and discharge nozzles of V = Victaulic coupling
identical nominal diameters arranged opposite to each other (in- E = thread (male)
line design).
Operating Data
Materials Movitec VE
Capacities Q up to 9.7 m3/h, (2.7 l/s)
Standard variants:
Heads H up to 57 m
VE, V: All hydraulic components are made of stainless steel
Operating pressures pd up to 10 bar 1)
AISI 304
VS, LHS: All hydraulic components are made of stainless steel Operating temperatures t - 15 _C to +60 _C
AISI 316 Movitec V(S)
Capacities Q up to 90 m3/h, (25 l/s)
Bearings Heads H up to 258 m
All V, VS and LHS pumps are supplied with tungsten carbide plain Operating pressures pd up to 25 bar 1)
bearing at the hydraulic rotor. Operating temperatures t - 15 _C to +120 _C
Movitec VE is supplied without bearing at the hydraulic rotor. Movitec LHS
Capacities Q up to 8.6 m3/h, (2.4 l/s)
Shaft Seal Heads H up to 415 m
Single-acting, uncooled mechanical seal in accordance with Operating pressures pd up to 40 bar 1)
EN 12756. Operating temperatures t - 15 _C to +120 _C
1) The sum of inlet pressure and head at zero flow point must not ex-
Drive ceed the value stated.
Electric motor, 50 Hz, air-cooled, 2- and 4-pole, standard KSB
motor with main dimensions to IEC. Other motor makes subject to Conformity Marks
prior consultation with KSB. CE
Movitec V, VS, LHS with PTC resistors for 3 kW and above. ACS (Movitec VE / V)
Variants: single-phase a.c. motor, frequency-controlled drives. ATEX group II, cat. 2 and 3 on request
 Movitec

Selection Charts
n [ 3500 1/min

LHS 6

V(S) 2

V(S) 4

V(S) 10 V(S) 18 V(S) 32 V(S) 45

V(S) 65

VE 2

VE 4

n [ 1750 1/min

2
 Movitec

Materials
Part No. Description Material
Movitec VE Movitec V Movitec VS Movitec LHS
101 Pump casing 1.4308 1.4301 1.4401 1.4408
108 Stage casing 1.4301 1.4404
160 Cover 1.4301 1.4404
171 Diffuser - 1.4301 1.4404 -
10-6 Pump shroud 1.4301 1.4404
210 Shaft 1.4305 1.4401
230 Impeller 1.4301 1.4404
341 Motor stool JL 1040 1.4408
412 O-ring EPDM VITON
525 Spacer sleeve 1.4301 1.4404
529 Bearing sleeve - Tungsten-carbide
1) Bearing - Ceramic
890 Baseplate JL 1040 -
905 Tie bolt 1.4057
920 Nut 1.4301 1.4404
932 Circlip 1.4571
1) Rigidly connected to stage casing 108 or diffuser 171

Legend of materials
Description Code and material no. Standard to ASTM

Cast iron JL1040 / GJL-250 EN 1561 A48:40B

Nickel chrome steel 1.4301 / X5CrNi18-10 EN 10088 A276:304
Nickel chrome molybdenum steel 1.4404 / X2CrNiMo 17-12-2 EN 10088 A276:316L
Carbon nickel chromium molybdenum steel 1.4408 / GX5CrNiMo19-11-2 EN 10213 A743CF8M
Nickel chrome molybdenum steel 1.4571 / X6CrNiMoTi17-12-2 EN 10088 A276:316
Nickel chrome steel 1.4057+QT800 / EN 10088-3 A276:431
X17CrNi16-2- QT800
1.4305 / X8CrNiS 18-9 EN 10088 A276:303
1.4401 / X5CrNiMo 17-12-2 EN 10088 A276:316
1.4308 / GX5CrNi 19-10 EN 10283 A743:CF8

Please note: The indication of the material designations to ASTM / AISI is not binding.

3
 Movitec

Material Codes
Mechanical seal Description Code letter to Material
EN 12756
Spring-loaded ring Q1 Silicon carbide (sintered pressure less)
U3 Tungsten carbide (CrNiMo-binder)
Seat ring B Resin-impregnated carbon graphite
U3 Tungsten carbide (CrNiMo-binder)
Elastomer E EPDM (Ethylene Propylene rubber)
V Fluorcarbon rubber (Viton)
X4 HNBR
Spring G CrNiMo steel
Other metal parts G CrNiMo steel
Code number 13 Q1BEGG Silicon carbide/Carbon/EPDM
14 Q1BVGG Silicon carbide/Carbon/Viton
15 U3U3X4GG Tungsten carbide/Tungsten carbide/HNBR
16 U3U3VGG Tungsten carbide/Tungsten carbide/Viton
17 U3BVGG Tungsten carbide/Carbon/Viton
(40 bar seal; only for Movitec LHS)

Pressure and Temperature Limits

Temperature
p of Flange
g variant / Material variant Max. operating
p g Code number Mechanical seal 5)
medium
di pumped d t 3) C
Connection
ti pressure ps 1) standard optional
– 15 _C to + 60 _C VE = thread Movitec VE up to 10 bar 13 -
– 15 _C to + 120 _C V = oval flange Movitec V up to 16 bar 13 14, 15, 16
Movitec VS up to 16 bar 14 13, 15, 16
– 15 _C to + 120 _C VF = round flange 2) Movitec VF 16 up to 25 bar 13 14, 15, 16
Movitec VSF 16 up to 25 bar 14 13, 15, 16
– 15 _C to + 120 _C VSV = Victaulic coupling Movitec VV up to 25 bar 13 14, 15, 16
Movitec VSV up to 25 bar 14 13, 15, 16
– 15 _C to + 120 _C LHS = round flange 4) Movitec LHS up to 40 bar 17 -
1) The sum of inlet pressure and head at zero flow point must not exceed the value stated.
2) Drilled to EN 1092-2 PN 25 (optional ASME B 16.1 Class 250 or JIS B2238 16K)
3) Subject to application limits (see List of Media Handled)
4) Drilled to EN 1092-2 PN 40
5) Movitec 24, 32 and 45 from 11 kW with cartridge seal; Movitec 65 generally with cartridge seal

4
 Movitec

Horizontal installation

The Movitec can be installed horizontally in systems where the Dimensions Movitec V, VS 2, 4, 10, 14, 18, 24, 32, 45, 65
installation conditions do not allow vertical installation.
Motor rating C 1) H A B Ident No.
Motor flange B14 (0.37 to 4.0 kW) set 2)
[kW] [mm] [mm] [mm] [mm]
Movitec V(S) (F) (V) 2, 4 - 2-pole
0.37 - 1.1 F2 + 47 120 100 100 47 116 958
1.5 - 2.2 F2 + 47 120 100 100 47 116 986
3.0 - 4.0 F2 + 39 120 100 100 47 116 959
5.5 - 7.5 F2 - 17 170 100 210 47 116 960
Movitec V(S) (F) (V) 10, 18 - 2-pole
0.55 - 1.1 F2 + 47 140 130 130 47 116 961
Motor flange B5 (5.5 and 7.5 kW) 1.5 - 2.2 F2 + 47 140 130 130 47 116 987
3.0 - 4.0 F2 + 39 140 130 130 47 116 962
5.5 - 7.5 F2 - 17 170 130 210 47 116 963
Movitec V(S) (F) (V) 14 - 4-pole
0.55 - 0.75 F2 + 47 140 130 130 47 116 964
1.1 - 1.5 F2 + 47 140 130 130 47 116 988
2.2 - 4.0 F2 + 39 140 130 130 47 116 965
Movitec VF, VSF 24 - 4-pole
The set for horizontal installation contains 2 stainless steel 1.1 - 1.5 F2 + 47 170 180 180 47 116 969
holding brackets and the required bolts.
2.2 - 4.0 F2 + 39 170 180 180 47 116 970
Foundation bolts must be supplied by the operator.
5.5 - 7.5 F2 - 17 170 180 180 47 116 971
Movitec VF, VSF 32, 45, 65 - 2-pole
1.5 - 2.2 F2 + 47 170 180 180 47 116 972
3.0 - 4.0 F2 + 39 170 180 180 47 116 973
5.5 - 7.5 F2 - 17 170 180 180 47 116 974
1) Height F2 based on stages, see type series booklet Movitec pp 39
2) Not available for Movitec VE and LHS

max. Ø 13 mm for M12

Holding bracket (pump) Holding bracket (motor)

89-11.01 89-11.02

5
 Movitec

Design Features Movitec VE

Universal pump up to 10 bar

• - 15 _C to 60 _C
Space-saving vertical design

Easy-to service, robust motor

• multi-range voltage / frequency
• type of enclosure IP 55
• insulation class F

Leak-free and resistant

to thermal shocks
Reliable, easy-to- • thanks to pump shroud
service shaft seal • due to confined O-rings
• standardized
mechanical seal
to EN 12756

Corrosion-resistant:
Special shaft of high- • hydraulic parts and pump
alloy steel with two flat shroud of high-alloy stainless steel
faces for strong
shaft/impeller
construction

High operating reliability

ensured by torsion-proof pump
Low noise, since the flow shroud
noise is dampened by • no partition lines on the outside
water-filled shroud • only 2 seal elements

Simple installation and piping layout

thanks to in-line design with thread
• insusceptible to outside nozzle
forces and moments
Integrated
non-return valve

6
 Movitec

Design Features Movitec V(S)

Universal high-pressure pump

up to 25 bar
• - 15 _C to 120 _C
• also for chemically aggressive
media
Space-saving vertical design

Easy-to service, robust

three-phase motor
• multi-range voltage /
frequency
• type of enclosure IP 55
• insulation class F
• with PTC resistor for
3 kW and above

Leak-free and resistant

to thermal shocks
• thanks to pump shroud
• due to confined O-rings

Reliable,
easy-to-service shaft seal
• standardized mechanical seal
to EN 12756

Easy-to-fit shaft of high-alloy

steel with two flat faces for
strong shaft/impeller construction
Corrosion-resistant:
• hydraulic parts and pump
shroud of high-alloy stainless
steel
• variant Movitec V features a
Low noise, since the flow pump of CrNi steelplate
noise is dampened by • variant Movitec VS features a
water-filled shroud pump of CrNiMo steelplate

High operating
reliability
ensured by torsion-
proof pump shroud
• no partition lines on
the outside
• only 2 seal elements

Simple installation
Highly wear-resistant and and piping layout
maintenance-free plain bearing of thanks to in-line design
tungsten carbide / ceramic • insusceptible to
lubricated by the medium outside nozzle
• self-cleaning by forced flushing forces and moments

7
 Movitec

Design Features Movitec LHS

Universal high–pressure pump

up to 40 bar
• - 15 _C to 120 _C
• also for chemically aggressive
media
Easy-to service, robust
Space-saving vertical design three-phase motor
• multi-range voltage / frequency
• type of enclosure IP 55
• insulation class F
• with PTC resistor for
3 kW and above

Leak-free and resistant

to thermal shocks
• thanks to pump shroud
• due to confined O-rings

Reliable, easy-to-service
shaft seal
• standardized mechanical seal
to EN 12756
Corrosion-resistant:
• hydraulic parts and
pump shroud of high-alloy
stainless CrNiMo steelplate
Easy-to-fit shaft of high-alloy
steel with two flat faces for
strong shaft/impeller construction
High operating
reliability
ensured by torsion-proof
pump shroud
Low noise, since the flow • no partition lines on the outside
noise is dampened by • only 2 seal elements
water-filled shroud

Simple installation and

Highly wear-resistant and piping layout
maintenance-free plain bearing of thanks to in-line design
tungsten carbide / ceramic • insusceptible to
lubricated by the medium outside nozzle
• self-cleaning by forced flushing forces and moments

8
 Movitec

Casing In the certificate of compliance with the order the manufacturing

Pump casing with suction and discharge nozzles of identical or processing works confirms by way of an informal report with-
nominal diameters arranged opposite to each other (in-line de- out specifying test results that the delivery complies with the sti-
sign). pulations of the purchase order (certificate to 2.2 and 3.1 avail-
Movitec VE and V(S): stainless steel pump casing and base- able upon request).
plate made of cast iron with powder coating.
Movitec LHS: stainless steel pump casing. Characteristic Curves 2)
The characteristic curves are based on the following principles:
Shaft Seal
F Tolerances to ISO 9906, Class 2 / Annex A.
The shaft seal is an uncooled, maintenance-free mechanical
seal to EN 12756. F The motors used for the measurements are standard KSB
motors 1).
Drive F The characteristic curves were obtained with deaerated water
Standard for V(S) and LHS: at a temperature of 20 _C and a density of 1.0 kg/dm3 1).
- Electric motor, 50 Hz, air-cooled, 2- and 4-pole, standard F The characteristic curves are valid for a kinematic viscosity
KSB motor with main dimensions to IEC. Other motor makes
of 1 mm2/s (1 cst) 1).
subject to prior consultation with KSB,
up to 2.2 kW 220 - 240 V/380 - 420 V, F A minimum permissible flow must be maintained to prevent
3 kW and above 380 - 420 V/660 - 725 V, the pump from overheating (see graph).
type of enclosure IP 55,
insulation class F, Movitec V Qmin in m3/h
up to 4 kW design V18,
2 0.3
5.5 kW and above design V1, 4 0.6
all motors with PTC resistor for 3 kW and above. 10 1.2
Approved variants: 14 1.0
- Explosion-proof motor II 2 G Eexd/Eexe T3/T4, 18 2.4
design V1/V18, make acc. to our choice. 24 2.2
- Motor for 500 V mains voltage, design V1/V18, make acc. to 32 4.0
our choice. 45 4.6
- Motor make acc. to customer’s choice (upon request). 65 6.1
- PTC thermistor for motors < 3 kW LHS 6 0.8
Standard for VE:
The following curve shows the minimum flow, corresponding
– Electric motor, 50 Hz, air-cooled, 2- and 4-pole, standard
KSB motor with main dimensions to IEC up to 2.2 kW to a percentage of the optimum flow Qopt, as a function of the
220 - 240 V/380 - 420 V, type of enclosure IP 55, insulation temperature of the medium pumped (flow rate at best effi-
class F. Motors with extended shaft. ciency point).
Direction of rotation: Minimum flow
Clockwise, seen from the drive side (see arrow indicating direc-
30
tion of rotation on the motor stool).
25
Q min [%]

Coupling (not on Movitec VE):

20
- All pump sizes: rigid coupling
- The couplings are in accordance with the EC Machinery 15
Safety Directive. 10
5
Installation
0
Vertical installation (horizontal installation see page 5) 40 50 60 70 80 90 100 110 120

Coating Temperature [5C]

Movitec VE and V(S): Cast iron motor stool and baseplate with
F Maximum pressure at the discharge nozzle:
powder coating.
10 bar – head at zero flow point with thread flange (VE).
Movitec V(S): Cast iron slide flanges protected by sheradising
16 bar – head at zero flow point with oval flange (V).
process.
25 bar – head at zero flow point with round flange (VF) and
All pumps: Stainless steel parts without any additional protec-
Victaulic coupling (VSV).
tive coating.
40 bar – head at zero flow point with round flange (LHS)
Tests F NPSH
Standard: The NPSH values of the individual characteristic curves are
Pressure test according to EN 809. minimum values corresponding to the cavitation limit; they
Leak test with water. refer to deaerated water.
A safety allowance of at least 0.5 m must be added when se-
Approved variant (upon request):
Hydraulic test evidenced by test report. This test is always car- lecting the pump to compensate for measuring inaccuracies
ried out using the original motor. and minor manufacturing deviations. The NPSH curve re-
The NPSH or the suction head are not measured. flects mean values.
1) In case of different parameters, the performance data must be cor-
Materials testing
Certificate of Compliance with the Order (corresponds to rected accordingly.
EN 10204) 2) See example on the following page.

9
 Movitec

Example

Number
of stages 12

Motor 7.5 kW / 10 HP
size

Qmin

NPSH required. A safety allowance of 0.5 m

must be added to the NPSH value of the
characteristic curve when selecting the system.

Power input per stage

at a density of ρ = 1 kg/dm3

Combination of Hydraulics
Movitec VE 2, 4

01 108.01 Stage casing

02 108.02 Stage casing with ceramic bearing
03 108.03 Stage casing without vanes
04 108.04 Stage casing bottom
05 108.05 Stage casing upper
06 108.06 Stage casing upper without vanes
Impeller location

no. of stages
7 05
6 05 01
5 05 01 01
4 05 01 01 01
3 06 05 01 01 01 01
2 03 01 01 01 01 01
1 04 04 04 04 04 04

Movitec VE 2 1 2 3 4 5 6
Movitec VE 4 1 2 3 4 5 6

10
 Movitec

Combination of Hydraulics
Movitec V 2, 4, 10, 14

01 108.01 Stage casing

02 108.02 Stage casing with ceramic bearing
03 108.03 Stage casing without vanes
04 108.04 Stage casing bottom
05 108.05 Stage casing upper
06 108.06 Stage casing upper without vanes
Impeller location

no. of casings

26 05
25 01
24 05 01
23 01 02
22 01 01
21 05 02 01
20 02 01 01
19 05 01 01 01
18 01 01 01 01
17 05 01 01 01 01
16 05 01 01 01 01 01
15 05 01 01 01 01 01 01
14 05 01 01 01 02 01 01 01
13 05 01 01 01 01 01 01 01 02
12 05 01 01 01 02 02 01 01 02 01
11 05 01 01 01 02 01 01 01 02 01 01
10 05 01 01 02 02 01 01 01 01 01 01 01
9 05 01 02 02 01 01 01 01 01 01 01 01 01
8 05 01 01 01 01 01 01 01 01 01 01 01 01 01
7 05 01 01 01 01 01 01 01 01 01 01 01 01 01 01
6 05 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01
5 05 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01
4 05 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01
3 06 05 01 01 01 01 02 02 02 01 01 01 01 01 01 01 01 01 01 01
2 02 02 02 02 02 02 01 01 01 02 02 02 02 02 02 02 02 02 02 02
1 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04

Movitec V 2- 1 2 3 4 5 6 7 8 9 10 11 13 15 16 18 20 23 25
Movitec V 4- 1 2 3 4 5 6 7 8 9 10 11 13 15 16 18 20 23 25
Movitec V 10 - 1 2 3 4 5 6 7 8 9 10 12 14 16 18 20
Movitec V 14 - 2 4 6 8 10 12 14 16 18 20

11
 Movitec

Combination of Hydraulics
Movitec V 18

01 108.01 Stage casing

02 108.02 Stage casing with ceramic bearing
04 108.04 Stage casing bottom
05 108.05 Stage casing Upper
06 108.06 Stage casing Upper without vanes
Impeller location

no. of casings
17 05
16 02
15 05 01
14 02 01
13 05 01 01
12 02 01 02
11 05 01 01 01
10 05 02 01 01 01
9 05 02 01 01 01 01
8 05 02 01 01 01 02 01
7 05 02 01 01 01 02 01 02
6 05 02 01 01 02 02 01 01 01
5 05 01 01 01 01 01 01 01 01 01
4 05 01 01 01 01 01 01 01 01 01 01
3 06 05 01 01 01 01 01 01 01 01 01 01 01
2 02 02 02 02 01 02 02 02 02 02 02 02 02
1 04 04 04 04 04 04 04 04 04 04 04 04 04

Movitec V 18 - 1 2 3 4 5 6 7 8 9 10 12 14 16

Movitec VF 24, 32, 45

01 171.01 Diffuser
02 171.02 Diffuser with ceramic bearing
03 171.03 Diffuser Upper
04 108.04 Stage casing bottom
Impeller location

no. of diffusers
17 03
16 02
15 01
14 01
13 03 01
12 03 02 01
11 03 02 01 02
10 03 02 01 01 01
9 03 02 01 01 02 01
8 03 02 01 01 01 01 01
7 03 02 01 01 02 02 01 02
6 03 02 01 01 01 01 01 01 01
5 03 02 01 01 02 02 01 01 02 01
4 03 01 01 01 01 01 01 01 01 01 01
3 03 01 01 01 01 01 01 01 01 01 01 01
2 02 02 02 02 01 02 02 02 02 02 02 02 02
1 04 04 04 04 04 04 04 04 04 04 04 04 04

Movitec VF 24 - 1 2 3 4 5 6 7 8 9 10 11 12 16
Movitec VF 32 - 1 2 3 4 5 6 7 8 9 10 11 12
Movitec VF 45 - 1 2 3 4 5 6 7 8 9 10

12
 Movitec

Combination of Hydraulics
Movitec VF 65

01 171.01 Diffuser
02 171.02 Diffuser with ceramic bearing
550 550 Disc Bottom
Impeller location

no. of diffusers
10 01
9 01 02
8 01 02 01
7 01 02 01 02
6 01 02 01 02 01
5 01 02 01 02 01 02
4 01 02 01 02 01 02 01
3 01 02 01 01 01 01 01 01
2 02 02 01 02 01 02 02 02 02
1 550 550 550 550 550 550 550 550 550

Movitec VF 65 - 1 2 3 4 5 6 7 8 9

Movitec LHS 6

01 108.01 Stage casing

02 108.02 Stage casing with ceramic bearing
04 108.04 Stage casing bottom
05 108.05 Stage casing Upper
Impeller location

no. of casings
21 05
20 02
19 05 01
18 02 01
17 05 01 01
16 02 01 01
15 05 01 01 01
14 02 01 01 02
13 05 01 01 01 01
12 02 01 01 01 01
11 05 01 01 01 01 01
10 02 01 01 01 02 01
9 01 01 01 02 01 01
8 01 01 02 01 01 02
7 01 02 01 01 01 01
6 01 01 01 01 01 01
5 01 01 01 01 01 01
4 01 01 01 01 01 01
3 01 01 01 01 01 01
2 02 02 02 02 02 02
1 04 04 04 04 04 04

Movitec LHS 6 - 10 12 14 16 18 20

13
 Movitec

Recommended Spare Parts Stock for 2 Years’ Continuous Operation

Number of pumps of identical size
(including stand-by pumps) -> 2 3 4 5 6 and 7 8 and 9 10 and more
Part No. Description Quantity of spare parts %
10-5 Stage casing compl. with bearing Kit 1 set 2 sets 3 sets 30
Stage casing with bearing (108.02) +
bearing sleeve (529) + impeller (230) +
spacer sleeve, short (525.01)
433 1 Mechanical seal 433 1 set 2 sets 3 sets 30
2 O-rings 412.01
2 Gasket (Oval) 400 (only for pumps with
V flange variant)
1 O-ring 412.05 (only for cartridge seal)
1 O-ring 412.06 (only for cartridge seal)

14
 Movitec

List of Media Handled

The data refer to the materials’ chemical resistance. Relevant regulations / standards for pump applications have to be complied
with.
The actual operating conditions must always be checked (concentration, temperature, solids content).
The penetration of air into the system must be avoided by all means.
If the operating conditions differ from the data given (e.g. mixed products) or if the media are not included in the table below, please
contact KSB.
Basic data:
- Temperature ranges:
D The reference temperature is 20 °C.
D In the case of temperatures <0 °C, please contact KSB.
D If the temperature exceeds > 50 °C, check and observe the fluid’s vapour pressure.
D Max. temperature = 120 °C, unless indicated otherwise.
- Max. concentration = 100 %, unless indicated otherwise.
- Mechanical seal of silicon carbide / carbon (Q1B): not suitable for media containing solids; this rule also covers particles develo-
ping as a result of salt crystallization at low fluid temperatures.
- Mechanical seal of tungsten carbide / tungsten carbide (U3U3): solids content max. 20 ppm (depending of particle size), with
the exception of corrosive media. Media with a higher abrasive solids content are as a rule not permitted. (ppm = 1 mg/kg).
- Please note: High temperatures will increase corrosion (reference temperature = 20 °C).
- Under unfavorable conditions (increased temperature, deposits, long periods of standstill) chloride contents of more than
300 mg/l may result in local corrosion.

Medium handled Content Temperature Mechanical seal variant

(see special conditions given at the end of max. max % max in °C
max.
the table) 13 14 15 16 17
Alcaline (bottle rinsing) (pH <9,5) 10 80 - - V 1) - -
Alcaline (metal degreasing) (pH <9,5) 10 80 - - V 1) - -
Alcohol (ethanol) 60 V/VE - - - -
Alum 3 80 - VS - - LHS
Aluminium sulphate 5 60 - - - V 1) -
Ammonium chloride (salmiac) 25 30 VS - - - -
Ammonium sulphate 20 60 V1)/VE1) - - - -
Antifreeze (glycol base), salt-free min. 20 V/VE - - - LHS
Antifreeze (halogen-free) 4) V/VE - - - -
Bicarbonate of ammonia 10 40 V1)/VE1) - - - -
Buttermilk 80 V1)/VE1) - - - LHS
Butyl alcohol (butanol) 60 V/VE - - - -
Calcium acetate 10 60 VS - - - -
Calcium nitrate (non-acidic) 10 60 - - - V 1) -
Cider 40 V1)/VE1) - - - LHS
Citric acid 25 30 - V 1) - - -
Copper sulphate 10 80 - - V 1) - -
Crude oil condensate 4) - V 1) - - LHS
Crude oil 4) 80 - V 1) - - LHS
Deionised water (demineralised) V1)/VE1) - - - -
Diesel oil (light, extra-light) 80 - V - - LHS
Ethanol (alcohol) 60 V/VE - - - -
Ethylene glycol/diethylene glycol (salt-free) 100 V/VE - - - LHS
Ferric sulphate (II) 10 80 - - - V -
Fruit juices pH neutral (6.5) 60 - V - - LHS
Fuel oil (light) (without antifreeze for - 20 °C
80 - V - - LHS
and below)
Glycerin 40 V/VE - - - LHS
Glycol (salt-free) (see Ethylene glycol) 100 V/VE - - - LHS
Hexan 40 - V - - LHS
Isopropyl alcohol (2-propanol) 80 V/VE - - - -
Kerosene 100 - V - - LHS
Lactic acid 40 60 - V 1) - - LHS
Liqueur 60 - V - - LHS
Magnesium sulphate 10 80 - V - - LHS
Maleic acid 10 60 - VS - - -
Miscellaneous 4) 60 - V 1) - - LHS

15
 Movitec

Medium handled Content Temperature Mechanical seal variant

(see special conditions given at the end of max %
max. max in °C
max.
the table) 13 14 15 16 17
Oil/water mixtures (without solids) - V - - LHS
Oils (without abrasive solids):
Corn oil 100 - V1)3) - - LHS
Cutting oil 4) 100 - - - V 3) -
Hydraulic oil 4) 80 - V 3) - - LHS
Linseed oil 60 - V 3) - - LHS
Linseed oil + 3 % H2SO4 60 - VS - - -
Lubricating oil 4) 100 - V 3) - - LHS
Mineral oil 4) 80 - V 3) - - LHS
Peanut oil - V 3) - - LHS
Rapeseed oil 100 - V 3) - - LHS
Salad oil 4) 100 - V 3) - - LHS
Silicon fluid 4) 60 - V 3) - - LHS
Soybean oil 100 - V 1)3) - - LHS
Turpentine oil 4) 60 - V 3) - - LHS
Turbine oil (no SDF oils) 4) 100 - V 3) - - LHS
Vegetable oils (free from H2SO4) 4) - V 3) - - LHS
Paraffin(s) 4) - V - - LHS
Petroleum (without solids) 80 - V - - LHS
Phosphoric acid 5 20 - V - - -
Polyethylene glycol 4) 80 V/VE - - - LHS
Polyglycols 4) 80 - V - - LHS
Potassium bicarbonate 10 60 - - V 1) - -
Potassium carbonate 25 60 - - V 1) - -
Potassium hydroxide 5 60 - - V 1) - -
Potassium nitrate 10 30 - - V 1) - -
Potassium sulphate 3 20 - VS - - LHS
Propyl alcohol (see isopropyl alcohol) 80 - - - - -
Soda lye (see sodium hydroxide) - - - - -
Sodium carbonate 6 60 V1)/VE1) - - - -
Sodium hydroxide (soda lye) 10 60 - - V 1) - -
Sodium nitrate (non-acidic) 10 60 V1)/VE1) - - - -
Sodium sulphate (non-acidic) 5 60 V1)/VE1) - - - -
Spirits 60 V/VE - - - -
Sulphuric acid 5 30 - VS 3) - - -
Tannic acid 20 80 - V 1) - - LHS
Tartaric acid 8 60 - V 1) - - LHS
Trisodium phosphate 4 80 - - V 1) - -
Turpentine (oil) (see oil; turpentine) 4) 60 - V - - LHS
Vinegar (wine vinegar) 10 60 VS - - - -

16
 Movitec

Medium handled Content Temperature Mechanical seal variant

(see special conditions given at the end of max %
max. max in °C
max.
the table) 13 14 15 16 17
Water/glycol mixture (salt-free with inhibi-
min. 20 V/VE - - - -
tors)
Water:
condensate VS 2) - - - -
cooling water - - - V 1) -
decarbonised water - - V 1) - -
deionised water V1)/VE1) - - - -
distilled water V1)/VE1) - - - -
drinking water V/VE - - - -
fire-fighting water - - V 1) - -
fully desalinated water (see deionised water) - - - - -
heating water V/VE - - - -
partly desalinated water (see
- - - - -
decarbonised water)
pure water (chemically neutral,
V1)/VE1) - - - -
no ultra pure water)
rinsing water - - - V 1) -
seawater (continuous operation) 25 - - - VS -
softened water (see decarbonised water) - - - - -
swimming pool water (no brine) - VS - - LHS
tap water V/VE - - - -
untreated water (suspended solids <20 ppm) - - V - -
Wine (white, red) 40 V1)/VE1) - - - LHS
1) Only valid if all standard (brass) plugs of the Movitec V are replaced by stainless steel plugs. Otherwise use a Movitec VS pump with the right
seal.
2) The water treatment shall be in accordance with the VdTÜV guidelines for feed and boiler water in steam plants of up to 64 bar.
The penetration of air into the system must be avoided by all means.
3) Pure media containing no abrasive solids.
4) Please contact KSB with detailed information on the fluid to be handled !

17
 Movitec

Movitec VE with standard KSB motor 3~230/400 V

Pump size Number Seal Motor Rated Thread
of code rating current Movitec VE
stages
kW Inom in A Ident No. kg
2 poles
Movitec VE 2 1 13 0.37 2.4 / 1.4 47 109 651 12.7
Movitec VE 2 2 13 0.37 2.4 / 1.4 47 109 652 12.7
Movitec VE 2 3 13 0.55 2.6 / 1.5 47 109 653 15.2
Movitec VE 2 4 13 0.75 3.7 / 2.1 47 109 654 18.3
Movitec VE 4 1 13 0.37 2.4 / 1.4 47 109 770 12.7
Movitec VE 4 2 13 0.55 2.6 / 1.5 47 109 771 14.7
Movitec VE 4 3 13 0.75 3.7 / 2.1 47 109 772 17.8
Movitec VE 4 4 13 1.1 5.8 / 3.3 47 109 773 19.6

18
 Movitec

Movitec V with standard KSB motor 3~230/400 V

Pump size Number Seal Motor Rated Oval flange Round flange Victaulic coupling
of code rating current Movitec V Movitec VF Movitec VV
stages
kW Inom in A Ident No. kg Ident No. kg Ident No. kg
2 poles
Movitec V 2 1 13 0.37 2.4 / 1.4 47 109 656 13.3 *) - 47 109 707 13.3
Movitec V 2 2 13 0.37 2.4 / 1.4 47 109 657 13.3 *) - 47 109 708 13.3
Movitec V 2 3 13 0.55 2.6 / 1.5 47 109 658 15.7 *) - 47 109 709 15.7
Movitec V 2 4 13 0.75 3.7 / 2.1 47 109 659 19.0 *) - 47 109 710 19.0
Movitec V 2 5 13 1.1 5.8 / 3.3 47 109 660 20.8 *) - 47 109 711 20.8
Movitec V 2 6 13 1.1 5.8 / 3.3 47 109 661 21.3 *) - 47 109 712 21.3
Movitec V 2 7 13 1.5 7.8 / 4.5 47 109 662 25.3 *) - 47 109 713 25.3
Movitec V 2 8 13 1.5 7.8 / 4.5 47 109 663 25.8 *) - 47 109 714 25.8
Movitec V 2 9 13 1.5 7.8 / 4.5 47 109 664 26.3 *) - 47 109 715 26.3
Movitec V 2 10 13 2.2 10.9 / 6.3 47 109 665 29.7 *) - 47 109 716 29.7
Movitec V 2 11 13 2.2 10.9 / 6.3 - - 47 109 666 30.8 47 109 717 30.2
Movitec V 2 13 13 2.2 10.9 / 6.3 - - 47 109 667 31.8 47 109 718 31.1
Movitec V 2 15 13 3 12.4 / 7.2 - - 47 109 668 42.7 47 109 719 42.0
Movitec V 2 16 13 3 12.4 / 7.2 - - 47 109 669 43.1 47 109 720 42.5
Movitec V 2 18 13 4 16.0 / 9.2 - - 47 109 670 53.1 47 109 721 52.4
Movitec V 4 1 13 0.37 2.4 / 1.4 47 109 774 13.3 *) - 47 109 824 13.3
Movitec V 4 2 13 0.55 2.6 / 1.5 47 109 775 15.3 *) - 47 109 825 15.3
Movitec V 4 3 13 0.75 3.7 / 2.1 47 109 776 18.6 *) - 47 109 826 18.6
Movitec V 4 4 13 1.1 5.8 / 3.3 47 109 777 20.3 *) - 47 109 827 20.3
Movitec V 4 5 13 1.5 7.8 / 4.5 47 109 778 24.4 *) - 47 109 828 24.4
Movitec V 4 6 13 1.5 7.8 / 4.5 47 109 779 24.9 *) - 47 109 829 24.9
Movitec V 4 7 13 2.2 10.9 / 6.3 47 109 780 28.3 *) - 47 109 830 28.3
Movitec V 4 8 13 2.2 10.9 / 6.3 47 109 781 28.8 *) - 47 109 831 28.8
Movitec V 4 9 13 3 12.4 / 7.2 47 109 782 39.3 *) - 47 109 832 39.3
Movitec V 4 10 13 3 12.4 / 7.2 47 109 783 39.7 *) - 47 109 833 39.7
Movitec V 4 11 13 3 12.4 / 7.2 - - 47 109 784 40.2 47 109 834 40.2
Movitec V 4 13 13 4 16.0 / 9.2 - - 47 109 785 50.1 47 109 835 50.1
Movitec V 4 15 13 4 16.0 / 9.2 - - 47 109 786 51.0 47 109 836 51.0
Movitec V 4 16 13 5.5 21.0 / 12.1 - - 47 109 787 59.2 47 109 837 57.6
Movitec V 10 1 13 0.75 3.7 / 2.1 47 109 874 23.2 *) - 47 109 915 23.2
Movitec V 10 2 13 1.5 7.8 / 4.5 47 109 875 28.2 *) - 47 109 916 28.2
Movitec V 10 3 13 2.2 10.9 / 6.3 47 109 876 31.9 *) - 47 109 917 31.9
Movitec V 10 4 13 3 12.4 / 7.2 47 109 877 42.8 *) - 47 109 918 42.8
Movitec V 10 5 13 3 12.4 / 7.2 47 109 878 43.5 *) - 47 109 919 43.5
Movitec V 10 6 13 4 16.0 / 9.2 47 109 879 53.2 *) - 47 109 920 53.2
Movitec V 10 7 13 5.5 21.0 / 12.1 47 109 880 60.0 *) - 47 109 921 60.0
Movitec V 10 8 13 5.5 21.0 / 12.1 47 109 881 60.7 *) - 47 109 922 60.7
Movitec V 10 10 13 7.5 26.8 / 15.5 - - 47 109 882 68.7 47 109 923 66.1
Movitec V 10 12 13 7.5 26.8 / 15.5 - - 47 109 883 70.1 47 109 924 67.5
Movitec V 10 14 13 11 53.7 / 31.0 - - 47 109 884 137.7 47 109 925 135.0
4 poles
Movitec V 14 2 13 0.55 4.5 / 2.6 47 109 944 22.3 *) - 47 109 968 22.3
Movitec V 14 4 13 1.1 4.8 / 2.8 47 109 945 29.0 *) - 47 109 969 29.0
Movitec V 14 6 13 1.5 6.5 / 3.7 47 109 946 33.1 *) - 47 109 970 33.1
Movitec V 14 8 13 2.2 8.4 / 4.9 47 109 947 44.4 *) - 47 109 971 44.4
Movitec V 14 10 13 3 14.5 / 8.4 47 109 948 47.0 *) - 47 109 972 47.0
Movitec V 14 12 13 4 17.5 / 10.1 47 109 949 56.6 *) - 47 109 973 56.6
Movitec V 14 14 13 4 17.5 / 10.1 47 109 950 58.2 *) - 47 109 974 58.2
Movitec V 14 16 13 5.5 19.8 / 11.5 47 109 951 92.9 *) - 47 111 954 92.9
Movitec V 14 18 13 5.5 19.8 / 11.5 47 109 952 94.5 *) - 47 109 975 94.5
Movitec V 14 20 13 7.5 27.0 / 15.6 47 109 953 107.1 *) - 47 109 976 107.1

*) available as factory option

19
 Movitec

Movitec V with standard KSB motor 3~230/400 V

Pump size Number Seal Motor Rated Oval flange Round flange Victaulic coupling
of code rating current Movitec V Movitec VF Movitec VV
stages
kW Inom in A Ident No. kg Ident No. kg Ident No. kg
2 poles
Movitec V 18 1 13 2.2 10.9 / 6.3 47 109 986 31.6 47 110 017 36.1 47 110 052 31.6
Movitec V 18 2 13 4 16.0 / 9.2 47 109 987 50.8 47 110 018 55.4 47 110 053 50.8
Movitec V 18 3 13 5.5 21.0 / 12.1 47 109 988 57.8 47 110 019 62.3 47 110 054 57.8
Movitec V 18 4 13 7.5 26.8 / 15.5 47 109 989 62.7 47 110 020 67.2 47 110 055 62.7
Movitec V 18 5 13 7.5 26.8 / 15.5 47 109 990 63.6 47 110 021 68.1 47 110 056 63.6
Movitec V 18 6 13 11 53.7 / 31.0 47 109 991 130.6 47 110 022 135.2 47 110 057 130.6
Movitec V 18 7 13 11 53.7 / 31.0 47 109 992 131.5 47 110 023 136.1 47 110 058 131.5
Movitec V 18 8 13 15 56.3 / 32.5 - - 47 110 024 151.0 47 110 059 146.4
Movitec V 18 9 13 15 56.3 / 32.5 - - 47 110 025 151.9 47 110 060 147.3
Movitec V 18 10 13 18.5 72.1 / 41.6 - - 47 110 026 167.8 47 110 061 163.2
Movitec V 18 12 13 18.5 72.1 / 41.6 - - 47 110 027 169.6 47 110 062 165.0
4 poles
Movitec V 24 1 13 1.1 4.8 / 2.8 - - 47 110 084 56.8 - -
Movitec V 24 2 13 1.5 6.5 / 3.7 - - 47 110 085 61.6 - -
Movitec V 24 3 13 2.2 8.4 / 4.9 - - 47 110 086 72.5 - -
Movitec V 24 4 13 3 14.5 / 8.4 - - 47 110 087 75.8 - -
Movitec V 24 5 13 4 17.5 / 10.1 - - 47 110 088 86.2 - -
Movitec V 24 6 13 5.5 19.8 / 11.5 - - 47 110 089 122.1 - -
Movitec V 24 7 13 5.5 19.8 / 11.5 - - 47 110 090 124.4 - -
Movitec V 24 8 13 7.5 27.0 / 15.6 - - 47 110 091 137.8 - -
Movitec V 24 9 13 7.5 27.0 / 15.6 - - 47 110 092 140.1 - -
Movitec V 24 10 13 7.5 27.0 / 15.6 - - 47 110 093 142.5 - -
Movitec V 24 11 11 7.5 27.0 / 15.6 - - 47 110 094 144.8 - -
Movitec V 24 12 13 11 44.0 / 25.3 - - 47 110 095 194.8 - -
Movitec V 24 16 13 15 57.4 / 33.0 - - 47 110 096 216.2 - -
2 poles
Movitec V 32 1 13 3 12.4 / 7.2 - - 47 110 120 69.9 - -
Movitec V 32 2 13 7.5 26.8 / 15.5 - - 47 110 121 91.2 - -
Movitec V 32 3 13 11 53.7 / 31.0 - - 47 110 122 162.5 - -
Movitec V 32 4 13 15 56.3 / 32.5 - - 47 110 123 178.8 - -
Movitec V 32 5 13 15 56.3 / 32.5 - - 47 110 124 181.1 - -
Movitec V 32 6 13 18.5 72.1 / 41.6 - - 47 110 125 198.4 - -
Movitec V 32 7 13 22 78.8 / 45.5 - - 47 110 126 236.7 - -
Movitec V 45 1-1 13 3 12.4 / 7.2 - - 47 110 160 70.9 - -
Movitec V 45 1 13 5.5 21.0 / 12.1 - - 47 110 161 86.0 - -
Movitec V 45 2-1 13 11 53.7 / 31.0 - - 47 110 162 161.3 - -
Movitec V 45 2 13 11 53.7 / 31.0 - - 47 110 163 161.4 - -
Movitec V 45 3-1 13 15 56.3 / 32.5 - - 47 110 164 177.7 - -
Movitec V 45 3 13 18.5 72.1 / 41.6 - - 47 110 165 192.8 - -
Movitec V 45 4-1 13 22 78.8 / 45.5 - - 47 110 166 230.9 - -
Movitec V 65 1 13 5.5 21.0 / 12.1 - - 47 110 185 93.1 - -
Movitec V 65 2 13 11 53.7 / 31.0 - - 47 110 186 166.7 - -
Movitec V 65 3 13 15 56.3 / 32.5 - - 47 110 187 184.1 - -
Movitec V 65 4 13 18.5 72.1 / 41.6 - - 47 110 188 202.5 - -
Movitec V 65 5 13 22 78.8 / 45.5 - - 47 110 189 241.9 - -

20
 Movitec

Movitec V with standard KSB motor 3~400/692 V

Pump size Number Seal Motor Rated Round flange
of code rating current Movitec VF
stages
kW Inom in A Ident No. kg
2 poles
Movitec V 32 8 13 30 56.1 / 32.4 47 111 940 358.8
Movitec V 32 9 13 30 56.1 / 32.4 47 111 941 365.1
Movitec V 45 4 13 30 56.1 / 32.4 47 111 944 355.0
Movitec V 45 5-1 13 30 56.1 / 32.4 47 111 945 357.4
Movitec V 45 5 13 30 56.1 / 32.4 47 111 946 357.4
Movitec V 45 6-1 13 37 65.5 / 37.8 47 111 947 359.8
Movitec V 45 6 13 37 65.5 / 37.8 47 111 948 359.8

21
 Movitec

Movitec VS with standard KSB motor 3~230/400 V

Pump size Number Seal Motor Rated Oval flange Round flange Victaulic coupling
of code rating current Movitec VS Movitec VSF Movitec VSV
stages
kW Inom in A Ident No. kg Ident No. kg Ident No. kg
2 poles
Movitec VS 2 1 14 0.37 2.4 / 1.4 47 110 249 13.3 *) - 47 110 300 13.3
Movitec VS 2 2 14 0.37 2.4 / 1.4 47 110 250 13.3 *) - 47 110 301 13.3
Movitec VS 2 3 14 0.55 2.6 / 1.5 47 110 251 15.7 *) - 47 110 302 15.7
Movitec VS 2 4 14 0.75 3.7 / 2.1 47 110 252 19.0 *) - 47 110 303 19.0
Movitec VS 2 5 14 1.1 5.8 / 3.3 47 110 253 20.8 *) - 47 110 304 20.8
Movitec VS 2 6 14 1.1 5.8 / 3.3 47 110 254 21.3 *) - 47 110 305 21.3
Movitec VS 2 7 14 1.5 7.8 / 4.5 47 110 255 25.3 *) - 47 110 306 25.3
Movitec VS 2 8 14 1.5 7.8 / 4.5 47 110 256 25.8 *) - 47 110 307 25.8
Movitec VS 2 9 14 1.5 7.8 / 4.5 47 110 257 26.3 *) - 47 110 308 26.3
Movitec VS 2 10 14 2.2 10.9 / 6.3 47 110 258 29.7 *) - 47 110 309 29.7
Movitec VS 2 11 14 2.2 10.9 / 6.3 - - 47 110 259 30.8 47 110 310 30.2
Movitec VS 2 13 14 2.2 10.9 / 6.3 - - 47 110 260 31.8 47 110 311 31.1
Movitec VS 2 15 14 3 12.4 / 7.2 - - 47 110 261 42.7 47 110 312 42.0
Movitec VS 2 16 14 3 12.4 / 7.2 - - 47 110 262 43.1 47 110 313 42.5
Movitec VS 2 18 14 4 16.0 / 9.2 - - 47 110 263 53.1 47 110 314 52.4
Movitec VS 4 1 14 0.37 2.4 / 1.4 47 110 351 13.3 *) - 47 110 401 13.3
Movitec VS 4 2 14 0.55 2.6 / 1.5 47 110 352 15.3 *) - 47 110 402 15.3
Movitec VS 4 3 14 0.75 3.7 / 2.1 47 110 353 18.6 *) - 47 110 403 18.6
Movitec VS 4 4 14 1.1 5.8 / 3.3 47 110 354 20.3 *) - 47 110 404 20.3
Movitec VS 4 5 14 1.5 7.8 / 4.5 47 110 355 24.4 *) - 47 110 405 24.4
Movitec VS 4 6 14 1.5 7.8 / 4.5 47 110 356 24.9 *) - 47 110 406 24.9
Movitec VS 4 7 14 2.2 10.9 / 6.3 47 110 357 28.3 *) - 47 110 407 28.3
Movitec VS 4 8 14 2.2 10.9 / 6.3 47 110 358 28.8 *) - 47 110 408 28.8
Movitec VS 4 9 14 3 12.4 / 7.2 47 110 359 39.3 *) - 47 110 409 39.3
Movitec VS 4 10 14 3 12.4 / 7.2 47 110 360 39.7 *) - 47 110 410 39.7
Movitec VS 4 11 14 3 12.4 / 7.2 - - 47 110 361 40.2 47 110 411 40.2
Movitec VS 4 13 14 4 16.0 / 9.2 - - 47 110 362 50.1 47 110 412 50.1
Movitec VS 4 15 14 4 16.0 / 9.2 - - 47 110 363 51.0 47 110 413 51.0
Movitec VS 4 16 14 5.5 21.0 / 12.1 - - 47 110 364 59.2 47 111 955 57.6
Movitec VS 10 1 14 0.75 3.7 / 2.1 47 110 444 23.2 *) - 47 110 485 23.2
Movitec VS 10 2 14 1.5 7.8 / 4.5 47 110 445 28.2 *) - 47 110 486 28.2
Movitec VS 10 3 14 2.2 10.9 / 6.3 47 110 446 31.9 *) - 47 110 487 31.9
Movitec VS 10 4 14 3 12.4 / 7.2 47 110 447 42.8 *) - 47 110 488 42.8
Movitec VS 10 5 14 3 12.4 / 7.2 47 110 448 43.5 *) - 47 110 489 43.5
Movitec VS 10 6 14 4 16.0 / 9.2 47 110 449 53.2 *) - 47 110 490 53.2
Movitec VS 10 7 14 5.5 21.0 / 12.1 47 110 450 60.0 *) - 47 110 491 60.0
Movitec VS 10 8 14 5.5 21.0 / 12.1 47 110 451 60.7 *) - 47 110 492 60.7
Movitec VS 10 10 14 7.5 26.8 / 15.5 - - 47 110 452 68.7 47 110 493 66.1
Movitec VS 10 12 14 7.5 26.8 / 15.5 - - 47 110 453 70.1 47 110 494 67.5
Movitec VS 10 14 14 11 53.7 / 31.0 - - 47 110 454 137.7 47 110 495 135.0
4 poles
Movitec VS 14 2 14 0.55 4.5 / 2.6 47 110 510 22.3 *) - 47 110 534 22.3
Movitec VS 14 4 14 1.1 4.8 / 2.8 47 110 511 29.0 *) - 47 110 535 29.0
Movitec VS 14 6 14 1.5 6.5 / 3.7 47 110 512 33.1 *) - 47 110 536 33.1
Movitec VS 14 8 14 2.2 8.4 / 4.9 47 110 513 44.4 *) - 47 110 537 44.4
Movitec VS 14 10 14 3 14.5 / 8.4 47 110 514 47.0 *) - 47 110 538 47.0
Movitec VS 14 12 14 4 17.5 / 10.1 47 110 515 56.6 *) - 47 110 539 56.6
Movitec VS 14 14 14 4 17.5 / 10.1 47 110 516 58.2 *) - 47 110 540 58.2
Movitec VS 14 16 14 5.5 19.8 / 11.5 47 110 517 92.9 *) - 47 110 541 92.9
Movitec VS 14 18 14 5.5 19.8 / 11.5 47 110 518 94.5 *) - 47 110 542 94.5
Movitec VS 14 20 14 7.5 27.0 / 15.6 47 110 519 107.1 *) - 47 110 543 107.1

*) available as factory option

22
 Movitec

Movitec VS with standard KSB motor 3~230/400 V

Pump size Number Seal Motor Rated Oval flange Round flange Victaulic coupling
of code rating current Movitec VS Movitec VSF Movitec VSV
stages
kW Inom in A Ident No. kg Ident No. kg Ident No. kg
2 poles
Movitec VS 18 1 14 2.2 10.9 / 6.3 47 110 552 31.6 47 110 583 36.1 47 110 618 31.6
Movitec VS 18 2 14 4 16.0 / 9.2 47 110 553 50.8 47 110 584 55.4 47 110 619 50.8
Movitec VS 18 3 14 5.5 21.0 / 12.1 47 110 554 57.8 47 110 585 62.3 47 110 620 57.8
Movitec VS 18 4 14 7.5 26.8 / 15.5 47 110 555 62.7 47 110 586 67.2 47 110 621 62.7
Movitec VS 18 5 14 7.5 26.8 / 15.5 47 110 556 63.6 47 110 587 68.1 47 110 622 63.6
Movitec VS 18 6 14 11 53.7 / 31.0 47 110 557 130.6 47 110 588 135.2 47 110 623 130.6
Movitec VS 18 7 14 11 53.7 / 31.0 47 110 558 131.5 47 110 589 136.1 47 110 624 131.5
Movitec VS 18 8 14 15 56.3 / 32.5 - - 47 110 590 151.0 47 110 625 146.4
Movitec VS 18 9 14 15 56.3 / 32.5 - - 47 110 591 151.9 47 110 626 147.3
Movitec VS 18 10 14 18.5 72.1 / 41.6 - - 47 110 592 167.8 47 110 627 163.2
Movitec VS 18 12 14 18.5 72.1 / 41.6 - - 47 110 593 169.6 47 110 628 165.0
4 poles
Movitec VS 24 1 14 1.1 4.8 / 2.8 - - 47 110 650 56.8 - -
Movitec VS 24 2 14 1.5 6.5 / 3.7 - - 47 110 651 61.6 - -
Movitec VS 24 3 14 2.2 8.4 / 4.9 - - 47 110 652 72.5 - -
Movitec VS 24 4 14 3 14.5 / 8.4 - - 47 110 653 75.8 - -
Movitec VS 24 5 14 4 17.5 / 10.1 - - 47 110 654 86.2 - -
Movitec VS 24 6 14 5.5 19.8 / 11.5 - - 47 110 655 122.1 - -
Movitec VS 24 7 14 5.5 19.8 / 11.5 - - 47 110 656 124.4 - -
Movitec VS 24 8 14 7.5 27.0 / 15.6 - - 47 110 657 137.8 - -
Movitec VS 24 9 14 7.5 27.0 / 15.6 - - 47 110 658 140.1 - -
Movitec VS 24 10 14 7.5 27.0 / 15.6 - - 47 110 659 142.5 - -
Movitec VS 24 11 14 7.5 27.0 / 15.6 - - 47 110 660 144.8 - -
Movitec VS 24 12 14 11 44.0 / 25.3 - - 47 110 661 194.8 - -
Movitec VS 24 16 14 15 57.4 / 33.0 - - 47 110 662 216.2 - -
2 poles
Movitec VS 32 1 14 3 12.4 / 7.2 - - 47 110 686 69.9 - -
Movitec VS 32 2 14 7.5 26.8 / 15.5 - - 47 110 687 91.2 - -
Movitec VS 32 3 14 11 53.7 / 31.0 - - 47 110 688 162.5 - -
Movitec VS 32 4 14 15 56.3 / 32.5 - - 47 110 689 178.8 - -
Movitec VS 32 5 14 15 56.3 / 32.5 - - 47 110 690 181.1 - -
Movitec VS 32 6 14 18.5 72.1 / 41.6 - - 47 110 691 198.4 - -
Movitec VS 32 7 14 22 78.8 / 45.5 - - 47 110 692 236.7 - -
Movitec VS 45 1-1 14 3 12.4 / 7.2 - - 47 110 725 70.9 - -
Movitec VS 45 1 14 5.5 21.0 / 12.1 - - 47 110 726 86.0 - -
Movitec VS 45 2-1 14 11 53.7 / 31.0 - - 47 110 727 161.3 - -
Movitec VS 45 2 14 11 53.7 / 31.0 - - 47 110 728 161.4 - -
Movitec VS 45 3-1 14 15 56.3 / 32.5 - - 47 110 729 177.7 - -
Movitec VS 45 3 14 18.5 72.1 / 41.6 - - 47 110 730 192.8 - -
Movitec VS 45 4-1 14 22 78.8 / 45.5 - - 47 110 731 230.9 - -
Movitec VS 65 1 14 5.5 21.0 / 12.1 - - 47 110 750 93.1 - -
Movitec VS 65 2 14 11 53.7 / 31.0 - - 47 110 751 166.7 - -
Movitec VS 65 3 14 15 56.3 / 32.5 - - 47 110 752 184.1 - -
Movitec VS 65 4 14 18.5 72.1 / 41.6 - - 47 110 753 202.5 - -
Movitec VS 65 5 14 22 78.8 / 45.5 - - 47 110 754 241.9 - -

23
 Movitec

Movitec VS with standard KSB motor 3~400/692 V

Pump size Number Seal Motor Rated Round flange
of code rating current Movitec VSF
stages
kW Inom in A Ident No. kg
2 poles
Movitec VS 32 8 14 30 56.1 / 32.4 47 111 942 358.8
Movitec VS 32 9 14 30 56.1 / 32.4 47 111 943 365.1
Movitec VS 45 4 14 30 56.1 / 32.4 47 111 949 355.0
Movitec VS 45 5-1 14 30 56.1 / 32.4 47 111 950 357.4
Movitec VS 45 5 14 30 56.1 / 32.4 47 111 951 357.4
Movitec VS 45 6-1 14 37 65.5 / 37.8 47 111 952 359.8
Movitec VS 45 6 14 37 65.5 / 37.8 47 111 953 359.8

24
 Movitec

Movitec LHS with standard KSB motor 3~230/400 V

Pump size Number Seal Motor Rated Round flange
of code rating current Movitec LHS
stages
kW Inom in A Ident No. kg
2 poles
Movitec LHS 6 8 17 7.5 26.8 / 15.5 47 110 762 96.1
Movitec LHS 6 10 17 11 53.7 / 31.0 47 110 763 165.2
Movitec LHS 6 12 17 11 53.7 / 31.0 47 110 764 168.2
Movitec LHS 6 14 17 15 56.3 / 32.5 47 110 765 185.2

25
*) Qmin up to 40 _C, temperatures >40 _C see table page 9
26
*) Qmin up to 40 _C, temperatures >40 _C see table page 9
27
*) Qmin up to 40 _C, temperatures >40 _C see table page 9
28
*) Qmin up to 40 _C, temperatures >40 _C see table page 9
29
 *) Qmin up to 40 _C, temperatures >40 _C see table page 9
30
*) Qmin up to 40 _C, temperatures >40 _C see table page 9
31
 *) Qmin up to 40 _C, temperatures >40 _C see table page 9
32
*) Qmin up to 40 _C, temperatures >40 _C see table page 9
33
 *) Qmin up to 40 _C, temperatures >40 _C see table page 9
34
*) Qmin up to 40 _C, temperatures >40 _C see table page 9
35
 *) Qmin up to 40 _C, temperatures >40 _C see table page 9
36
*) Qmin up to 40 _C, temperatures >40 _C see table page 9
37
 Movitec

Dimension Tables
Movitec VE 2 3500 1/min

VE 2

No. of stages E1 E2 F1
1 134 107 413
2 134 107 413
3 134 107 458
4 150 115 470
Dimensions in mm

Movitec VE 4 3500 1/min

VE 4

No. of stages E1 E2 F1
1 134 107 413
2 134 107 437
3 150 115 449
4 150 115 500
Dimensions in mm

Terminal Box Position for all pump sizes see page 48

38
 Movitec

Dimension Tables
Movitec V 2 3500 1/min
Oval flange Round flange
V2
Victaulic flange
No. of stages E1 E2 F1 F2 F1 F2
1 134 107 451 232 476 257
2 134 107 451 232 476 257
3 134 107 496 253 521 278
4 150 115 518 284 543 309
5 150 115 569 305 594 330
6 150 115 590 326 615 351
7 176 136 632 357 657 382
8 176 136 653 378 678 403
9 176 136 674 399 699 424
10 176 136 695 420 720 445
11 176 136 716 441 741 466
13 176 136 758 483 783 508
15 194 147 851 535 876 560
16 194 147 872 556 897 581
18 233 162 922 598 947 623
Dimensions in mm

Flange Variants
Oval flange PN 16 Round flange PN 25 Victaulic PN 25
Movitec V(S) Movitec V(S) F Movitec V(S) V

Terminal Box Position for all pump sizes see page 48

39
 Movitec

Dimension Tables
Movitec V 4 3500 1/min
Oval flange Round flange
V4
Victaulic
No. of stages E1 E2 F1 F2 F1 F2
1 134 107 451 232 476 257
2 134 107 475 232 500 257
3 150 115 497 263 522 288
4 150 115 548 284 573 309
5 176 136 590 315 615 340
6 176 136 611 336 636 361
7 176 136 632 357 657 382
8 176 136 653 378 678 403
9 194 147 725 409 750 434
10 194 147 746 430 771 455
11 194 147 767 451 792 476
13 233 162 817 493 842 518
15 233 162 859 535 884 560
16 233 162 885 556 910 581
Dimensions in mm

Flange Variants
Oval flange PN 16 Round flange PN 25 Victaulic PN 25
Movitec V(S) Movitec V(S) F Movitec V(S) V

Terminal Box Position for all pump sizes see page 48

40
 Movitec

Dimension Tables
Movitec V 10 3500 1/min

V 10

No. of stages E1 E2 F1 F2
1 150 115 556 322
2 176 136 607 332
3 176 136 634 359
4 194 147 712 396
5 194 147 739 423
6 233 162 774 450
7 233 162 826 497
8 233 162 853 524
10 233 162 935 578
12 233 162 989 632
14 315 206 1218 716
Dimensions in mm

Flange Variants
Oval flange PN 16 Round flange PN 25 Victaulic PN 25
Movitec V(S) Movitec V(S) F Movitec V(S) V

Terminal Box Position for all pump sizes see page 48

41
 Movitec

Dimension Tables
Movitec V 14 1750 1/min

V 14

No. of stages E1 E2 F1 F2
2 156 119 556 322
4 173 112 643 386
6 173 136 720 440
8 200 151 817 504
10 198 150 872 558
12 225 168 935 612
14 225 168 989 666
16 255 181 1100 740
18 255 181 1154 794
20 255 181 1248 848
Dimensions in mm

Flange Variants
Oval flange PN 16 Victaulic PN 25
Movitec V(S) Movitec V(S) V

Terminal Box Position for all pump sizes see page 48

42
 Movitec

Dimension Tables
Movitec V 18 3500 1/min

V 18

No. of stages E1 E2 F1 F2
1 176 136 632 357
2 233 162 691 367
3 233 162 750 421
4 233 162 813 456
5 233 162 847 490
6 315 206 1057 555
7 315 206 1091 589
8 315 206 1126 624
9 315 206 1160 658
10 315 206 1239 693
12 315 206 1308 762
Dimensions in mm

Flange Variants
Oval flange PN 16 Round flange PN 25 Victaulic PN 25
Movitec V(S) Movitec V(S) F Movitec V(S) V

Terminal Box Position for all pump sizes see page 48

43
 Movitec

Dimension Tables
Movitec VF 24 1750 1/min

VF 24

No. of stages E1 E2 F1 F2
1 176 136 738 458
2 176 136 786 506
3 194 147 871 555
4 194 147 919 603
5 233 162 976 652
6 266 179 1103 720
7 266 179 1152 769
8 266 179 1238 817
9 266 179 1287 866
10 266 179 1335 914
11 266 179 1384 963
12 312 230 1553 1116
16 312 230 1787 1310
Dimensions in mm

Flange Variants
Round flange PN 25
Movitec V(S) F

Terminal Box Position for all pump sizes see page 48

44
 Movitec

Dimension Tables
Movitec VF 32 3500 1/min

VF 32

No. of stages E1 E2 F1 F2
1 194 147 774 458
2 233 162 883 526
3 315 206 1182 680
4 315 206 1230 728
5 315 206 1279 777
6 315 206 1371 825
7 350 225 1469 874
8 398 323 1572 922
9 398 323 1621 971
Dimensions in mm

Flange Variants
Round flange PN 25
Movitec V(S) F

Terminal Box Position for all pump sizes see page 48

45
 Movitec

Dimension Tables
Movitec VF 45 3500 1/min

VF 45

No. of stages E1 E2 F1 F2
1-1 194 147 774 458
1 233 162 807 478
2-1 315 206 1133 631
2 315 206 1133 631
3-1 315 206 1182 680
3 315 206 1226 680
4-1 350 225 1323 728
4 398 323 1378 728
5-1 398 323 1427 777
5 398 323 1427 777
6-1 398 323 1475 825
6 398 323 1475 825
Dimensions in mm

Flange Variants
Round flange PN 25
Movitec V(S) F

Terminal Box Position for all pump sizes see page 48

46
 Movitec

Dimension Tables
Movitec VF 65 3500 1/min

Round flanges
VF 65
PN 16
No. of stages E1 E2 F1 F2
1 233 162 919 590
2 315 206 1211 709
3 315 206 1300 798
4 315 206 1433 887
5 350 225 1571 976
Dimensions in mm

Flange Variants
Round flanges PN 16

Terminal Box Position for all pump sizes see page 48

47
 Movitec

Dimension Tables
Movitec LHS 6 3500 1/min

LHS 6

No. of stages E1 E2 F1 F2
8 233 162 896 539
10 315 206 1131 629
12 315 206 1190 688
14 315 206 1250 748
Dimensions in mm

Terminal Box Position for all Pump Sizes

Terminal box position

(plant view)

Flange Variants
Round flange PN 40

Position 3
(Standard Movitec V, VS, LHS)

Position 9
(Standard Movitec VE)

Position 6

Position 12
(not for Movitec VE)

48
Movitec

49
 Movitec

Sectional Drawing
Movitec VE 2, 4

20030219-B

50
 Movitec

Part No. Description

10-6 Pump shroud

101 Pump casing
108.01 Stage casing
108.04 Stage casing, bottom
108.05 Stage casing, upper
160 Cover
230 Impeller
341 Motor stool
411.01 Joint ring
411.03 Joint ring
411.04 Joint ring
412.01 O-ring
412.03 O-ring
433 Mechanical seal
525.03 Spacer sleeve, long
525.04 Spacer sleeve, end
525.05 Spacer sleeve, seal
554.01 Washer
742 Non-return valve
802 Motor for close coupling
890 Baseplate, cast
903.01 Screwed plug
903.02 Screwed plug
903.03 Screwed plug
905 Tie bolt
914.02 Hexagon socket head cap screw
920.02 Nut lock with non metallic insert
920.03 Nut
930 Safety device nord-lock
932 Circlip

51
 Movitec

Sectional Drawing
Movitec V 2, 4, 10, 14, 18

95000589-F

52
 Movitec

Part No. Description

10-6 Pump shroud

101 Pump casing
108.01 Stage casing
108.02 Stage casing, with ceramic bearing
108.04 Stage casing, bottom
108.05 Stage casing, upper
160 Cover
210 Shaft
230 Impeller
341 Motor stool
400 Gasket, oval
411.01 Joint ring
411.02 Joint ring EPDM
412.01 O-ring
412.02 O-ring
412.03 O-ring
412.04 O-ring
433 Mechanical seal
525.01 Spacer sleeve, short
525.03 Spacer sleeve, long
525.04 Spacer sleeve, end
525.05 Spacer sleeve, seal
529 Bearing sleeve
554.01 Washer
554.02 Washer
554.03 Washer
560 Pin
681 Coupling guard
723 Flange, oval
800 Motor (> 5,5 kW 801 Flange motor)
862 Coupling shell
890 Baseplate, cast
901.01 Hexagon head bolt
901.02 Hexagon head bolt
901.03 Hexagon head bolt
903.01 Screwed plug
903.02 Screwed plug
905 Tie bolt
914.01 Hexagon socket head cap screw
920.01 Nut
920.02 Nut lock, with non metallic insert
920.03 Nut
930 Safety device, nord-lock
932 Circlip (1/1)

53
 Movitec

Sectional Drawing
Movitec VF 24, 32, 45

20010712-E

54
 Movitec

Part No. Description Detail cartridge seal

10-6 Pump shroud

101 Pump casing
108.04 Stage casing, bottom
160 Cover
171.01 Diffuser
171.02 Diffuser, with ceramic bearing
171.03 Diffuser, upper
210 Shaft
230 Impeller (for Movitec VF 24 and 32)
230.01 Impeller (for Movitec VF 45)
230.02 Impeller, half head (for Movitec VF 45)
341 Motor stool
411.01 Joint ring
412.01 O-ring
412.02 O-ring
412.03 O-ring
412.04 O-ring
412.05 O-ring
412.06 O-ring
433 Mechanical seal
471 Seal cover
500 Ring, cartridge
509.01 Intermediate ring
509.02 Intermediate ring, upper
525.01 Spacer sleeve, short
525.03 Spacer sleeve, long
525.04 Spacer sleeve, end
525.05 Spacer sleeve, seal
525.06 Spacer sleeve, seal extention
525.07 Spacer sleeve, cartridge
529 Bearing sleeve
554.01 Washer
560 Pin
681 Coupling guard
800 Motor (> 5,5 kW 801 Flange motor)
862 Coupling shell
890 Baseplate, cast
901.01 Hexagon head bolt
903.01 Screwed plug
903.02 Screwed plug
904 Grub screw
905 Tie bolt
914.01 Hexagon socket head cap screw
914.02 Hexagon socket head cap screw
914.03 Hexagon socket head cap screw
920.01 Nut
920.02 Nut, lock with non metallic insert
920.03 Nut
930 Safety device, nord-lock
932 Circlip (1/2)

55
 Movitec

Sectional Drawing
Movitec VF 65

20000752-F

56
 Movitec

Part No. Description

10-6 Pump shroud

101 Pump casing
160 Cover
171.01 Diffuser
171.02 Diffuser, with ceramic bearing
210 Shaft
230 Impeller
341 Motor stool
411.01 Joint ring
412.01 O-ring
412.02 O-ring
412.04 O-ring
412.05 O-ring
412.06 O-ring
433 Mechanical seal
471 Seal cover
500 RingCartridge
509.01 Intermediate ring
509.02 Intermediate ring, upper
509.03 Intermediate ring, lower
525.01 Spacer sleeve, short
525.02 Spacer sleeve, middle
525.03 Spacer sleeve, long
525.04 Spacer sleeve, end
525.05 Spacer sleeve, seal
525.07 Spacer sleeve, cartridge
529 Bearing sleeve
550 Disc Bottom
554.01 Washer
554.04 Washer
560 Pin
681 Coupling guard
722 Tap piece, flanged
801 Flange motor
862 Coupling shell
890 Baseplate, cast
901.01 Hexagon head bolt
901.04 Hexagon head bolt
903.01 Screwed plug
903.02 Screwed plug
904 Grub screw
905 Tie bolt
914.01 Hexagon socket head cap screw
914.02 Hexagon socket head cap screw
914.03 Hexagon socket head cap screw
920.01 Nut
920.02 Nut lock with non metallic insert
920.03 Nut
920.05 Nut
930 Safety device, nord-lock
932 Circlip (1/2)

57
 Movitec

Sectional Drawing
Movitec LHS 6

20030238-B

58
 Movitec

Part No. Description

10-6 Pump shroud

101 Pump casing
108.01 Stage casing
108.02 Stage casing with ceramic bearing
108.04 Stage casing, bottom
108.05 Stage casing, upper
210 Shaft
230 Impeller
341 Motor stool
411.01 Joint ring
411.04 Joint ring
412.01 O-ring
412.03 O-ring
433 Mechanical seal
525.01 Spacer sleeve, short
525.02 Spacer sleeve, middle
525.03 Spacer sleeve, long
525.04 Spacer sleeve, end
525.05 Spacer sleeve, seal
529 Bearing sleeve
554.01 Washer
554.02 Washer
554.04 Washer
560 Pin
681 Coupling guard
722 Tap piece, flanged
801 Motor
862 Coupling shell
901.01 Hexagon head bolt
901.02 Hexagon head bolt
901.04 Hexagon head bolt
903.01 Screwed plug
903.02 Screwed plug
905 Tie bolt
914.01 Hexagon socket head cap screw
920.01 Nut
920.02 Nut lock with non metallic insert
920.03 Nut
920.05 Nut
930 Safety device nord-lock
932 Circlip

59
 Movitec

Subject to technical modifications without prior notice.

1.7.2005
1798.56/3-10

KSB Aktiengesellschaft
67225 Frankenthal • Johann-Klein-Str. 9 • 67227 Frankenthal (Germany)
Tel. +49 6233 86-0 • Fax +49 6233 86-3401 • www.ksb.com